BioStar 1 8 Administrator Guide - EN PDF

f
BioStar 1.8
Administrator Guide
BioStar 1.8 Administrator Guide
Suprema Warranty Policy ................................................................................... vii
Disclaimers................................................................................ vii
Copyright Notice ..................................................................... viii
01 About the BioStar System ..................................................... 9
1.1 Logical Configuration ....................................................................... 12
1.2 Access Control Features ................................................................... 14
1.2.1 User Authentication ............................................................................... 14
1.2.2 User Management ................................................................................. 16
1.2.3 Access Group Management ................................................................... 16
1.2.4 Device Management .............................................................................. 16
1.2.5 Door and Elevator (Lift) Management .................................................... 17
1.2.6 Zone Management ................................................................................ 17
1.2.7 Time and Attendance ............................................................................. 17
1.2.8 IP Camera and NVR Server Management ............................................... 17
02 Install the BioStar Software .................................................. 19

2.1 System Requirements ....................................................................... 19
2.2 Run the BioStar Installer ................................................................... 20
2.3 Install the BioStar Server Application ............................................... 23
2.3.1 Configure the MySQL Database ............................................................. 25
2.3.2 Configure the BioStar Server .................................................................. 25
2.4 Install the BioStar Client Application ................................................ 27
2.4.1 Log in to BioStar for the First Time ......................................................... 29
2.4.2 BioStar Interface .................................................................................... 30
2.5 Customize the BioStar Interface ....................................................... 31
2.5.1 Change the Theme ................................................................................ 31
2.5.2 Customize the Toolbar ........................................................................... 32
2.5.3 Change Event Views ............................................................................... 33
2.6 Migrate a Database from BioAdmin to BioStar ................................ 33
03 Setup the BioStar System ..................................................... 35

3.1 Create Administrative Accounts ....................................................... 35
3.1.1 Administrative Levels ............................................................................. 35
Copyright 2014, Suprema Inc. On the web: www.supremainc.com ii

3.1.2 Add and Customize Administrative Accounts ......................................... 36

3.2 Setup Devices ................................................................................... 39
3.2.1 Search for and Add Devices ................................................................... 39
3.2.2 Search for and Add Slave Devices .......................................................... 41
3.2.3 Add an RF Device................................................................................... 42
3.2.4 Connect a Device via Wireless LAN ........................................................ 43
3.2.5 Configure a BioStation Device ................................................................ 45
3.2.6 Configure a BioEntry Plus or BioEntry W Device ..................................... 47
3.2.7 Configure a BioLite Net Device .............................................................. 49
3.2.8 Configure an Xpass or Xpass Slim Device ............................................... 50
3.2.9 Configure a D-Station Device ................................................................. 52
3.2.10 Configure an X-Station Device ............................................................... 54
3.2.11 Configure a BioStation T2 Device ........................................................... 55
3.2.12 Configure a FaceStation Device .............................................................. 58
3.2.13 Change Wiegand Formats ...................................................................... 59
3.3 Setup Doors ..................................................................................... 63
3.3.1 Add a Door ............................................................................................ 63
3.3.2 Associate a Device With a Door ............................................................. 63
3.3.3 Configure a Door ................................................................................... 64
3.3.4 Create a Door Group.............................................................................. 64
3.4 Setup Elevators (Lifts) ....................................................................... 65
3.4.1 Add an Elevator ..................................................................................... 65
3.4.2 Associate a Device With an Elevator ....................................................... 65
3.4.3 Configure an Elevator............................................................................. 66
3.4.4 Add Users to an Elevator ........................................................................ 66
3.4.5 Transfer Settings to an Elevator .............................................................. 67
3.5 Setup Zones ..................................................................................... 68
3.5.1 Determine Which Zones to Use.............................................................. 68
3.5.2 Add and Configure Zones ...................................................................... 70
3.6 Setup Users ...................................................................................... 75
3.6.1 Create a User Account ........................................................................... 76
3.6.2 Register Fingerprints .............................................................................. 77
3.6.3 Capture Face Images .............................................................................. 80
3.6.4 Issue Access Cards ................................................................................. 82
3.6.5 Transfer User Data.................................................................................. 90
3.6.6 User Data Encryption ............................................................................. 93
Copyright 2014, Suprema Inc. On the web: www.supremainc.com iii

3.7 Setup Timezones .............................................................................. 94

3.7.1 Create a Timezone ................................................................................. 94
3.7.2 Create a Holiday Schedule ..................................................................... 95
3.8 Setup Access Groups ........................................................................ 97
3.8.1 Add an Access Group ............................................................................. 97
3.8.2 Add Users to Access Groups .................................................................. 98
3.8.3 Assign Access Groups to Users............................................................... 98
3.8.4 Transfer Access Groups to Devices ......................................................... 99
3.8.5 Check for Access Rules by Device........................................................... 99
3.9 Setup Time and Attendance ........................................................... 100
3.9.1 Add a Time Category ........................................................................... 100
3.9.2 Add a Daily Schedule ........................................................................... 102
3.9.3 Add a Shift ........................................................................................... 104
3.9.4 Assign Users to Shifts .......................................................................... 105
3.9.5 Choose a Device for T&A ..................................................................... 107
3.10 Setup Alarms .................................................................................. 108
3.10.1 Configure Alarm Settings and Sounds .................................................. 109
3.10.2 Configure email notifications ............................................................... 111
3.10.3 Configure Settings for External Devices ................................................ 113
3.11 Setup Cameras ............................................................................... 115
3.11.1 Add an NVR Server .............................................................................. 116
3.11.2 Add an IP Camera ................................................................................ 118
3.11.3 Configure an IP Camera ....................................................................... 120
04 Manage the BioStar System .............................................. 121

4.1 Monitor Events in Real Time ........................................................... 121
4.1.1 Monitor Muster Zones in Real Time ..................................................... 123
4.1.2 Monitor Areas with Cameras in Real Time ............................................ 124
4.2 View Event Logs ............................................................................. 124
4.2.1 Upload Logs to BioStar ........................................................................ 125
4.2.2 View Logs in User, Door, and Zone Panes ............................................. 126
4.2.3 View Logs from the Monitoring Pane ................................................... 126
4.2.4 View Access Logs ................................................................................. 127
4.3 Monitor Door Events via a Visual Map ........................................... 128
4.3.1 Create a Visual Map ............................................................................. 128
Copyright 2014, Suprema Inc. On the web: www.supremainc.com iv

4.3.2 Monitor Doors on a Visual Map ........................................................... 129

4.4 Control Doors, Alarms, and Devices Remotely ............................... 132
4.4.1 Open or Close Doors ........................................................................... 132
4.4.2 Release Alarms..................................................................................... 132
4.4.3 Lock or Unlock Devices ........................................................................ 132
4.5 Manage Users ................................................................................ 135
4.5.1 Delete Users ........................................................................................ 135
4.5.2 Transfer Users to Other Departments ................................................... 137
4.5.3 Customize User Information Fields ....................................................... 137
4.5.4 Export User Data .................................................................................. 138
4.5.5 Import User Data ................................................................................. 139
4.6 Manage Time and Attendance ....................................................... 140
4.6.1 Monitor T&A Status via the IO Board ................................................... 140
4.6.2 Generate T&A Reports ......................................................................... 141
4.6.3 Modify T&A Reports ............................................................................ 144
4.6.4 Print or Export T&A Report Data .......................................................... 145
4.7 Manage Devices ............................................................................. 146
4.7.1 Remove Devices ................................................................................... 146
4.7.2 Upgrade Device Firmware .................................................................... 146
4.7.3 Downgrade Device Firmware ............................................................... 147
4.8 Activate Fingerprint Encryption ...................................................... 147
4.9 Change the Fingerprint Template ................................................... 148
05 Customize Settings ............................................................ 149

5.1 Customize Device Settings ............................................................. 149
5.1.1 Customize Settings for BioStation Devices ........................................... 149
5.1.2 Customize Settings for BioEntry Plus or BioEntry W Devices ................ 162
5.1.3 Customize Settings for BioLite Net Devices .......................................... 173
5.1.4 Customize Settings for Xpass Devices .................................................. 186
5.1.5 Customize Settings for Xpass Slim Devices........................................... 197
5.1.6 Customize Settings for D-Station Devices ............................................ 207
5.1.7 Customize Settings for X-Station Devices ............................................. 221
5.1.8 Customize Settings for BioStation T2 Devices....................................... 232
5.1.9 Customize Settings for FaceStation Devices ......................................... 248
Copyright 2014, Suprema Inc. On the web: www.supremainc.com v

5.2 Customize Door Settings ................................................................ 262

5.2.1 Details tab ........................................................................................... 262
5.2.2 Alarm tab ............................................................................................. 264
5.3 Customize Zone Settings................................................................ 265
5.3.1 Customize Settings for Anti-Passback Zones ........................................ 265
5.3.2 Customize Settings for Entrance Limit Zones ....................................... 267
5.3.3 Customize Settings for Alarm Zones .................................................... 269
5.3.4 Customize Settings for Fire Alarm Zones .............................................. 271
5.3.5 Customize Settings for Access Zones ................................................... 273
5.3.6 Customize Settings for Muster Zones................................................... 274
5.3.7 Customize Settings for Interlock Zones ................................................ 276
5.4 Customize User Settings ................................................................ 276
5.4.1 Details Tab ........................................................................................... 277
5.4.2 Fingerprints Tab ................................................................................... 278
5.4.3 Face Tab ............................................................................................... 278
5.4.4 Face (Fusion) Tab.................................................................................. 279
5.4.5 Card Tab .............................................................................................. 279
5.4.6 T&A Tab ............................................................................................... 280
06 Technical Support .............................................................. 281

Glossary .................................................................................. 282
Copyright 2014, Suprema Inc. On the web: www.supremainc.com vi

Warranty and Disclaimers
Suprema Warranty Policy

Suprema warrants to Buyer, subject to the limitations set forth below, that each product shall operate
in substantial accordance with the published specifications for such product for a period of one (1)
year from the date of shipment of products ("Warranty Period"). If Buyer notifies Suprema in writing
within the Warranty Period of any defects covered by this warranty, Suprema shall, at its option, repair
or replace the defective product that is returned to Suprema within the Warranty Period, with freight
and insurance prepaid by Buyer. Such repair or replacement shall be Suprema's exclusive remedy for
breach of warranty with respect to the Product. This limited warranty shall not extend to any product
that has been: (i) subject to unusual physical or electrical stress, misuse, neglect, accident or abuse, or
damaged by any other external causes; (ii) improperly repaired, altered or modified in any way unless
such modification is approved in writing by the Supplier; (iii) improperly installed or used in violation
of instructions furnished by Suprema.
Suprema shall be notified in writing of defects in the RMA (Return Material Authorization) report
supplied by Suprema not later than thirty days after such defects have appeared and at the latest one
year after the date of shipment of the Product. The report should include full details of each defective
product, model number, invoice number, and serial number. No product without an RMA number
issued by Suprema may be accepted and all defects must be reproducible for warranty service.
Except as expressly provided herein, the products are provided "as is" without warranty of any kind,
either express or implied, including, but not limited to, warranties or merchantability and fitness for a
particular purpose.
Disclaimers
The information in this document is provided in connection with Suprema products. No license,
express or implied, by estoppels or otherwise, to any intellectual property rights is granted by this
document, except as provided in Supremas Terms and Conditions of Sale for such products.
Suprema assumes no liability whatsoever and Suprema disclaims any express or implied warranty,
relating to sale and/or use of Suprema products, including liability or warranties relating to fitness for a
particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual
property right.
Suprema products are not intended for use in medical, lifesaving, or life sustaining applications or
other applications in which the failure of the Suprema product could create a situation where personal
injury or death may occur. Should Buyer purchase or use Suprema products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Suprema and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Suprema was
negligent regarding the design or manufacture of the part.
Copyright 2014, Suprema Inc. On the web: www.supremainc.com vii

Suprema reserves the right to make changes to specifications and product descriptions at any time
without notice to improve reliability, function, or design. Designers must not rely on the absence or
characteristics of any features or instructions marked "reserved" or "undefined." Supreme reserves
these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities
arising from future changes to them.
Please contact Suprema, local Suprema sales representatives or local distributors to obtain the latest
specifications before placing your order.
Copyright Notice
This document is copyrighted 2008-2013 by Suprema, Inc. All rights reserved. All other product
names, trademarks, or registered trademarks are property of their respective owners.
Copyright 2014, Suprema Inc. On the web: www.supremainc.com viii

01
About the BioStar
System
BioStar is Suprema's next-generation access control system, based on IP connectivity and biometric
security. Most system devices integrate fingerprint scanners and card readers for multiple levels of user
authentication. However, Suprema's biometric devices, installed at each door, work not only as card or
fingerprint scanners and card readers, but also as intelligent access controllers.
The licensed standard edition of BioStar is unlocked by a USB dongle. Without the dongle, BioStar
functions as a free, but limited-capability version. With the dongle, BioStar offers greater versatility and
additional features, as shown in the table below:
Standard Edition Free Version
Maximum # of doors 512 20
Maximum # of clients 32 2
Zone support Yes No
Email notifications Yes No
Server matching Yes No
Shift types Daily and Weekly Weekly only
IO board Yes No
Visual Map Yes No
Copyright 2014, Suprema Inc. On the web: www.supremainc.com 9

1. About the BioStar System
BioStar V1.8 supports the following devices:
BioStation (V1.5 or later): BioStation is a multifunctional terminal with a

keypad and a 2.5-inch color LCD monitor that allows you to perform user
enrollment and administration functions directly from the device. BioStation
can be connected to a network via a wireless LAN or Ethernet and includes
USB host and device interfaces for easy data transfer. BioStation MIFARE
(BSM) models also support entry control via smart cards.
BioStation T2: BioStation T2 is a multifunctional, IP-based access control

terminal with a camera, 5-inch touchscreen, fingerprint scanner, card reader,
and built-in video phone feature.
D-Station: D-Station is a multifunctional, IP-based access control terminal

with a camera, touchscreen, and dual fingerprint scanners that allows for
multiple authorization combinations via fingerprint recognition (single or
dual), MIFARE access cards, user IDs, and face detection. D-Station can be
powered directly via an Ethernet connection to eliminate the need for
additional wiring or power connections.
FaceStation: FaceStation is a multifunctional, IP-based access control

terminal with an LCD touchscreen and a camera for face recognition and
videophone functions. FaceStation supports multiple interfaces for
connecting to computers or networks and access controls via Wiegand and
I/O ports. In addition, the device allows for authorization via multiple access
cards.
BioEntry Plus (V1.2 or later): BioEntry Plus is an IP-based access control

device that includes both fingerprint recognition and entry via access card.
The device can be controlled independently via command cards or managed
entirely via the BioStar interface. BioEntry Plus can be connected to electric
door strikes via an internal relay or used with the Secure I/O device for extra
security and expanded capability.

BioEntry W : The BioEntry W includes all of the features of the BioEntry Plus
in a vandal-resistant, IP65-rated structure. BioEntry W is ideal for outdoor
installation, with exceptional durability in harsh environments. It features
extensive communication interfaces and PoE cabability.
BioLite Net (V1.0 or later): BioLite Net is IP-based fingerprint terminal

designed specifically for outdoor use. With a rugged, IP65-rated waterproof
structure, it offers extra durability to withstand the elements. As either a
simple door control or part of a complex, networked environment, BioLite
Net supports the full functionality of BioStars time and attendance and
access control features.
Xpass: Xpass is an IP-based access reader/controller designed exclusively for

use with RF cards. It provides many similar functions to the BioEntry Plus
device, but is waterproof for outdoor use and can be connected and
powered by a single CAT5/6 cable.
Xpass Slim: The XPass Slim device is a slimmer version of the Xpass that
supports FeliCa and ISO 15693 cards. Its low profile allows it to be installed
in tight spaces and it features access control to floors when connected with
a LIFT I/O device via RS485 slave.
X-Station: X-Station is an easy-to-use smart IP terminal with a 3.5-inch

touchscreen LCD that supports ID and card access only. The device supports
face detection with a built-in camera. X-Station allows you to store up to
200,000 users with 1GB of internal flash memory and 256MB of RAM.
BioMini/BioMini Plus: The BioMini and BioMini Plus devices are fingerprint
scanners that can be used for convenient user enrollment. Installing the
device is simple: plug them into a USB connection on any computer that is
connected to the BioStar server and install a driver.

Secure I/O: The Secure I/O device provides a convenient way to increase the
security of externally mounted devices or expand the capabilities of your
system. When doors are controlled by a secure I/O device, intruders cannot
open doors even if they succeed in uninstalling external devices. To further
increase security, the secure I/O device provides encrypted communications
between door components. The Secure I/O device has four input switches
and two output relays to allow control of multiple components with a single
device.
LIFT I/O: The LIFT I/O supports 0-9 device IDs and 12 output ports (12 input
ports are not currently supported). Each output can be connected to an
elevator button to control access to floors. The LIFT I/O can be connected
via RS485 as a slave to Xpass and Xpass Slim devices. Up to 10 LIFT I/O
devices can be connected to an Xpass or Xpass Slim device to control up to
120 floors.
1.1 Logical Configuration

BioStar is a distributed intelligence system. Instead of the complex wiring and centralized
control required by conventional access control systems, Suprema's access control devices
can be connected via TCP/IP or wirelessly to a local area network or connected directly via
serial connections. User information, access rules, and other data can be distributed to each
device to speed up authorization time and provide continual operation even when the
connection to the network is lost.
As the following graphic illustrates, the BioStar system does not require separate access
controllers. This feature provides a distinct advantage over other access control systems,
because BioStation, BioEntry Plus, or BioEntry W devices act simultaneously as both a
controller and a reader. As a result, Suprema's distributed intelligence approach requires less
hardware and less wiring than conventional, centralized access control systems.

BioStar is a server-client application that supports up to 32 clients (2 clients maximum in the

free version). A typical configuration consists of numerous access control devices connected
to a central server via Ethernet, WLAN, and/or RS485. BioStar is compatible with MS SQL
Server and MySQL databases.

Overall, the system supports a maximum of 512 doors and 512 devices (20 doors and
devices in the free version). Networked devices can be easily grouped together to create
various combinations of anti-passback or alarm zones, as illustrated by the graphic that
follows.
1.2 Access Control Features

The BioStar system goes a step beyond conventional access control systems, by combining unique
biometric identification with configurable access card capabilities.
1.2.1 User Authentication

Suprema's access control devices incorporate advanced, award-winning fingerprint
recognition algorithms to provide secure access control. When used with the numerical
keypads on BioStation terminals or the face detection features of the D-Station, X-Station,
BioStation T2, and FaceStation devices, the system allows for a wide variety of user
authentication modes:
Fingerprint or access card: either a fingerprint scan or access card may be used to gain
entry.
Fingerprint + access card: both fingerprint scan and access card are required for
access.
User ID + fingerprint: a user ID and fingerprint scan are used in combination; the user
ID identifies the user and the fingerprint scan is used for authorization.
User ID + password: a user ID and password are used in combination; the user ID
identifies the user and the password is used for authorization.

User ID + card + fingerprint: a user ID, access card, and fingerprint scan are used in
combination.
Fingerprint only: authentication via a fingerprint scan is the only method to gain entry.
Card only: authentication via an access card is the only method to gain entry.
[D-Station Only]
Fingerprint + fingerprint: dual fingerprints are used in fusion.
Fingerprint + face detection: a fingerprint and face detection are used in fusion.
Fingerprint + fingerprint + face detection: dual fingerprints and face detection are
used in fusion.
[FaceStation Only]
Face: authentication via face recognition is the only method to gain entry.
Face + Password: authentication via face recognition plus password.
Face + Card: authentication via face recognition plus access card.
Face + Card or Password: authentication via face recognition plus access card or
password.
Face + Card + Password: authentication via face recognition plus card plus password.
User ID + Face: authentication via user ID plus face recognition.
User ID + Face or Password: authentication via user ID plus face regognition or
password.
User ID + Face + Password: authentication via user ID plus face recognition plus
password.
[D-Station, X-Station, BioStation T2, and FaceStation]

Detect face: upon successful authentication, a face image is captured.
BioStar stores two templates of each fingerprint and up to two fingerprints per user (four
templates total). If desired, one fingerprint can be used as a duress signal, to activate alarms
or send alerts in situations where a user is required to gain access under duress. Duplicate
templates of each print enhance authentication performance by reducing the likelihood of
false rejections. For more information about registering fingerprints, see section 3.6.2.
BioStar also provides administrators with the ability to read EM4100 and HID proximity cards
and read, issue, and format MIFARE and iCLASS access cards. For more information
about access cards, see section 3.6.4.

D-Station devices allow the system to store images of users and control access via face
detection, in addition to fingerprint, access card, and user ID authentication. D-Station, X-
Station, BioStation T2 and FaceStation devices are equipped with cameras to allow for face
detection and recording of face images for enhanced security. For more information about
face detection, see section 3.6.3.
1.2.2 User Management

BioStar supports both manual and automatic modes for user management. Manual
synchronization is available for enrolling different subsets of users to particular devices or
when the total number of users in the BioStar database exceeds the limits of a BioStation,
BioEntry Plus, BioEntry W, BioLite Net, Xpass, Xpass Slim, D-Station, X-Station, BioStation T2
or FaceStation device. Automatic synchronization is available when managing user records at
the device is not required or desired.
BioStar collects log records from devices and allows the data to be exported to a delimited
text file (.CSV) for custom reporting. The software supports an unlimited number of user
recordsthe maximum amount of data stored is subject only to the capabilities of the
underlying database and hardware configuration. For more information about user
management, see sections 4.1, 4.2, 4.3, 4.5, and 4.6.
1.2.3 Access Group Management

BioStar allows administrators to build custom access groups by combining permissions for
timezones and doors. With this capability, BioStar provides customizable, scheduled access
control.
BioStar supports up to 128 timezones that consist of a seven day schedule, plus two holiday
schedules. Each day in a timezone can include as many as five distinct time periods.
In total, BioStar supports up to 128 access groups that can be transferred to all connected
devices. For more information about access groups, see section 3.8.
1.2.4 Device Management

Administrators can control multiple aspects of devices via the BioStar software. In addition to
authentication behaviors, BioStar supports the configuration of inputs, output relays, actions,
and sounds. The system includes options for customizing sound and display settings for
BioStation, D-Station, X-Station, BioStation T2 and FaceStation devices, and LED & Buzzer
settings for other devices.
The system provides configuration options for controlling external devices, such as door
strikes and alarm sirens. BioStar can also connect to and communicate with third-party
devices via a Wiegand interface. For more information about device management, see
sections 3.2 and 4.7.

1.2.5 Door and Elevator (Lift) Management

BioStar allows for comprehensive control of doors and connected devices, such as door
relays, alarm relays, door sensors, and exit switches. Each door can be operated by up to two
devices and, when two devices are connected to a door, administrators can apply anti-
passback controls. BioStar also allows for control of elevators (lifts) via Xpass and Xpass Slim
devices, with Secure I/O devices connected as slaves.
BioStar allows specific configuration of alarm events for doors that are forced open or held
open longer than a specified interval, including activating alarm sounds from individual
devices, sending signals to external alarm sirens, displaying warnings in the BioStar user
interface, and sending e-mail notifications (not available in the free version). In addition,
administrators or operators can remotely lock and unlock doors or reset alarms. For more
information about door management, see sections 3.3, 4.3, and 4.4. For more information
about elevator management, see section 3.4.
1.2.6 Zone Management

The BioStar system gives administrators complete control of various zones (not available in
the free version). Zones can be created with devices connected via Ethernet or RS485 and
can include a master device and up to 65 member devices. In addition, individual devices
can be included in up to four zones.
BioStar supports zones for increased access control, such as anti-passback and entrance limit
zones, as well as zones that provide control for alarm or fire alarm outputs and actions.
BioStar also allows administrators to synchronize time, event logs, and user data for all
devices in a specified zone. For more information about zone management, see section 3.5.
1.2.7 Time and Attendance

BioStar versions 1.2 and higher include time and attendance features to allow administrators
to define time categories, shifts, daily schedules, and holiday settings. The T&A capabilities
of BioStar can be used to enforce compliance with check-in and check-out procedures,
restrict access to off-duty personnel, and report attendance data.
BioStar allows administrators to customize T&A functions for BioStation, D-Station, X-
Station, BioStation T2 and FaceStation devices and to specify how events are recorded. The
BioStar interface also allows administrators to monitor a user s check-in and check-out
status in real time. For more information about time and attendance, see sections 3.9 and
4.6.
1.2.8 IP Camera and NVR Server Management

BioStar versions 1.5 and higher support internet protocol (IP) cameras and network video
recorder (NVR) servers, to allow administrators to monitor areas and be notified of specific

events with real-time still images transferred from the IP cameras. By interoperating with the
NVR servers, the BioStar system can also display time-sorted event logs, together with
recorded videos stored on the servers. From the BioStar interface, administrators can add
and customize IP cameras and their functions. For more information about the IP cameras
and NVR servers, see sections 3.11 and 4.1.

Install the BioStar Software
02
Install the BioStar
Software
Installing BioStar is a fairly simplistic process, provided that you address a few prerequisites before
beginning the installation:
First, you must select a PC that can remain running constantly to function as the BioStar server. The
server will receive and store log data from connected devices in real time.
Second, you must choose a type of database to use. The BioStar server supports either MySQL or
MS SQL Server (including the scaled-down, free MS SQL Server Express). Regardless of which
database you choose, you must have sufficient access rights and privileges to connect to the
database and create new tables.
Third, ensure that the PCs you will use for both server and client applications meet the minimum
requirements listed in section 2.1.
The BioStar installation CD includes the BioStar installer. By default, the installer will install both the
server and client applications with minimal input (see section 2.2). However, you may choose to install
the server and client applications independently if you need to specify additional database options or
desire to install the applications on separate PCs (see sections 2.3 and 2.4).
2.1 System Requirements

BioStar supports the following operating systems:
Windows 8 (32-bit and 64-bit system)
Windows 7 (32-bit or 64-bit platform)
Windows Server 2008 R2
Windows Vista
Windows XP, Service Pack 1 or later

2. Install the BioStar Software
Windows Server 2003
Windows 2000, Service Pack 4 or later
The minimum system requirements for installing and operating the BioStar software include
the following:
CPU: Intel Pentium or similar processor, capable of processing speeds of 1GHz or faster
RAM: 512MB
HDD: 5GB
However, Suprema recommends the following hardware configuration for optimal

performance:
CPU: Intel Pentium Dual Core or similar processor, capable of processing speeds of
2GHz or faster
RAM: 1GB for Windows XP; 2GB for other operating systems
HDD: 10GB
2.2 Run the BioStar Installer

You should run the BioStar installer when you desire to install both the server and client
applications on the same PC and are willing to use the MS SQL Server Express database with
default settings. You will be required to intervene in the express installation process only
when MS SQL Server or a variation is already installed. In this case, you will be asked
whether or not you wish to install MS SQL Server Express. If you choose not to install the
express version, you will be required to provide the correct authentication details, as
described in step 7 of section 2.3.
!
Attention: If you have installed a previous installation on the machine with BioStar
installer, remove the old version before runninng the BioStar Installer.
The installer will install the following components:

BioStar server application
Auxiliary libraries: OpenSSL and Microsoft Visual C++ Redistributable
MS SQL Server Express
BioStar client application
BADB Conv (database migration tool)

Before you run the BioStar installer, close all other open applications. If you have previously
installed BioAdmin on the same machine, ensure that you stop the BioAdmin server before
beginning the installation.

To run the installer:

1. Insert the BioStar installation CD into a compatible media drive.
2. Locate the installation directory and run BioStar 1.8 Setup.
3. Follow the on-screen prompts to begin the installation.
4. During the installation, you will be asked to select the language of your preference.
Select a language, then click Next to proceed.
5. Make sure that both the Server and Client applications are selected in the Select
Features dialog box, then click Next to proceed.
6. Follow the instructions on the screen to finish the installation.

Note: BioStar versions 1.3 and higher include drivers for connecting BioStation and D-
Station devices via USB in Windows 7. These drivers will not work with older versions of
BioStar. If you are using an older version of BioStar be sure to install the correct USB drivers.

2.3 Install the BioStar Server Application

If you do not choose to install the BioStar server and client applications together, you need
to select only the application you would like to install at the Select Features dialog box
during the installation of the Biostar Setup. After you ensure that your system meets the
minimum requirements listed in section 2.1 and address the prerequisites mentioned in the
introduction to this chapter, close all other open applications. If you have previously installed
BioAdmin on the same machine, ensure that you stop the BioAdmin server before beginning
the installation.
!
Attention: If you have installed a previous installation on the machine with BioStar
installer, remove the old version before runninng the BioStar Installer.
The installer includes the following components:

To install the BioStar server application:

2. Locate the installation directory and run BioStar 1.8 Setup.
3. Follow the on-screen prompts to begin the installation.

5. At the Select Features dialog box, click the Client checkbox to uncheck it and exclude
the Biostar client application in the installation (both the server and slient applications
are checked by default), then click Next to proceed.

7. During the installation, you will be required to accept the OpenSSL license agreement
and select a destination folder for the OpenSSL program files.
8. You will also be asked whether or not you wish to install the MS SQL Server Express
edition. If you will use a pre-installed version of MS SQL Server, MySQL or Oracle, you
may click No when this message appears. If you decide to use the express edition in
this step, you can skip to step 10. The database setup process will be automated when
you install the express edition.
9. When the Create Database [BioStar] dialog box appears, select a database type (MS
SQL Server, MySQL or Oracle). The database server address and port numbers will be
automatically populated, but you should verify that they are correct.
Note: The default name for the database is always BioStar, to prevent unintentional
installation of multiple databases on the same system or database server. The database

name can be changed by editing the DBSetup.exe file. When patching the database server,
you will have the option to manually select a datbase.
10. If you choose MS SQL Server, you must configure the authentication method as well
(MySQL allows only server authentication):
Server authentication: this option uses login IDs and passwords to authenticate
users that are created by and stored on the SQL Server. These credentials are not
based on Windows user accounts. Users connecting via server authentication must
provide their credentials every time that they connect.
Windows authentication: this option uses Windows users accounts for
authentication. When users connect through a Windows user account, the SQL
Server validates the account name and password using the Windows principal
token in the operating system. The SQL Server does not ask for a password and
does not independently validate user identification. Windows authentication is the
default authentication mode for MS SQL Server.
Note: You must choose the authentication mode that is supported by the database. You
must also provide the proper credentials to create new tables in the database.
11. Click Setup to create the SQL database.

12. When the SQL database setup is complete, click Finish.
13. The setup program will perform a few remaining processes before the
server installation is complete. Click Finish.
2.3.1 Configure the MySQL Database

BioStar cannot use the MySQL database if the maximum packet size is less than 16MB. To
configure the maximum packet size n MySQL server, locate and open a configuration file for
the MySQL server (my.ini for a Windows system or my.cnf for a Linux system). Under
[mysqld], add or edit the packet size to 16M or bigger (for example:
max_allowed_packet=16M). After you have changed and saved the file, restart the BioStar
Server for the changes to take effect.
2.3.2 Configure the BioStar Server

In some cases, you may require manual configuration of the BioStar server. If you are having
trouble connecting to the server from the client application, for example, you may need to
alter your server settings. In addition, you must stop and restart the server application to
apply any changes you have made to server configurations or database settings.

On desktop, click BioStar Server Config to start BioStar Server setting program. Or, in
Windows, Start > All programs > BioStar 1.8 > Server Service > BioStar Server Config
- Server matching: When matching servers, system is supported to be improved according to

numbers of the system CPU cores as matcher features have been enhanced. So, the more
core numbers, it is able to expect the faster matching speed. Server matching item of BioStar
Server Config supports the settings as belows:
- Number of Core shows the numbers of cores to be used by matcher, and default is 2.
The server configuration utility allows you to monitor and control the following:
Status: view and modify the current status of the BioStar server (Stopped or Started).
You can stop and start the server by clicking the Start or Stop button on the right.
Connection: view and modify the details for the connection between the server and
devices.
TCP Port: enter the port that devices and client applications use to connect to the
server. You should use a port that is not shared with any other software
applications. In most cases, you can use the default port (1480).

Thread Count: enter the maximum thread count that the BioStar server can create.
You can enter any number between 32 and 512; however, keep in mind a larger
thread count will consume more system resources.
Client List: click this button to view a list of devices that are connected to the
BioStar server. The list shows the IP address of each device and whether or not a
SSL certificate has been issued to the device. You can issue or remove SSL
certificates directly from the utility.
Database: view and modify database settings. For more information about how to alter
these settings, see the procedure for setting up the BioStar server in section 2.3.
Max Connection: specify the maximum number of connections between the server
and the database. In most cases, the default value (1) is appropriate.
SSL: view or modify the settings for OpenSSL. Click Browse to locate the path for the
OpenSSL application or click Change to change the pass phrase.
2.4 Install the BioStar Client Application

If you do not choose to install the BioStar server and client applications together, you need
to select only the application you would like to install at the Select Features dialog box
during the installation of the Biostar Setup.
Before you install the BioStar client application, close all other running applications.
The installer includes the following components:
To install BioStar client application:

2. Run BioStar 1.8 Setup to launch the installation wizard.
3. Follow the on-screen prompts to install the BioStar Client.


5. At the Select Features dialog box, click the Server checkbox to uncheck it and exclude
the Biostar server application in the installation (both the server and client applications
are checked by default), then click Next to proceed.

2.4.1 Log in to BioStar for the First Time

If you restarted the system after installation, the BioStar server should run automatically in
the background. If you have not restarted the system, you may be required to manually
connect to the server before proceeding (see section 2.3.2). When logging in to BioStar for
the first time, you will be prompted to create an administrator account.
To log in for the first time:

1. Launch the BioStar program. If BioStar successfully connects to the server, the Add
New Administrator dialog box will open. In this case, skip to step 6. If BioStar cannot
connect to the server, the Login dialog box will open and display the message Cannot
connect to server.

2. Click Server Setting. This will open the Connect Server dialog box.
3. Enter the IP address and port number of the BioStar server.

4. Click Test to verify the connection.
5. Click Save to store the connection settings. This will open the Add New Administrator
dialog box.
6. Enter an Admin ID and password, confirm the password, and choose an administration
level from the drop-down level.
7. Click OK. This will return you to the Login dialog box.
8. Enter a User ID and password and click Login.
2.4.2 BioStar Interface

BioStar is composed of various interface elements. Each element uses a standard name, please
check names of each element before you read this manual.

Each element is named as what is displayed in the title. For example, it is called User window,
Customize dialog box, Additional Infomation tab, Basic Information area.
2.5 Customize the BioStar Interface

You do not have to make any changes to the interface to use the BioStar systemthe
default settings are sufficient for setup and operation. However, BioStar allows you to
customize various settings to control the appearance and functionality of the interface.
2.5.1 Change the Theme

The BioStar interface includes two preset themes based on MS Office styles:
Office 2003
Office 2007
To change the theme, click Theme from the menu bar and select a theme.

2.5.2 Customize the Toolbar

The BioStar interface includes a standard toolbar near the top left of the screen. Standard
toolbar buttons provide functions similar to a typical web browser: Back, Forward, Refresh,
Find User (search), and Print.
To customize the toolbar:

1. Click the drop-down arrow at the right of the toolbar.
2. Click Add or Remove Buttons > Customize. This will open the Customize dialog box.
3. Click the Commands tab.
4. Click All Commands to display a list of available buttons.
5. Drag a command to the toolbar. This will add a new button for the command.

2.5.3 Change Event Views

BioStar allows you to change the default period of events to show in the Event tab for users
or doors and zones. You can set the interface to show event details for 1 day, 3 days, or 1
week by default.
To change the event view:
1. From the menu bar, click View > Event View.
2. Click type of event view to change (User or Doors/Zone).
3. Click a default event period (1 day, 3 day, or 7 day).
2.6 Migrate a Database from BioAdmin to BioStar

The BioStar installation program includes a database migration tool called BADB Conv. This
tool allows you to migrate an existing BioAdmin database to your new BioStar system.
When migrating a database, any identical information that exists in the BioStar database will
be overwritten. For example, if you have added a user to BioStar that previously existed in
BioAdmin, the user data will be overwritten with the information from the BioAdmin
database. For this reason, you should migrate your old database to BioStar before creating
new user accounts.
To migrate your information from BioAdmin to BioStar:

1. Locate and run the migration program, BADBConv.exe. The location of this program is
Windows Start > All Programs > BioStar 1.8 > Server Service > BADBConv.
2. Click Yes to acknowledge the warning dialogue that appears to remind you that
identical information in BioStar will be overwritten.
3. Click Start to begin the migration. When the process is complete, the Convert DB
dialog box will show the types of data that have been migrated.

4. Click Close to exit the migration tool.

03
3. Setup the BioStar System
Setup the BioStar

System
This section describes how to add administrator accounts, devices, doors, zones, departments, users,
and access groups and setup time and attendance within the BioStar software. This administrator's
guide does not cover procedures for installing physical components, wiring doors and devices, or
connecting devices to networks. For more information about hardware installation and physical
configuration of your access control system, please refer to the installation guides that accompany
your access control devices.
3.1 Create Administrative Accounts

Before adding users, it is a good idea to add and configure accounts for system
administrators and operators. It is also useful to understand some general concepts
regarding administration of the BioStar system.
3.1.1 Administrative Levels

BioStar allows for multiple levels of administration, operation, and interaction with the
system. Each administrative level has varying degrees of privileges and access to the system
menus (User, Doors, Visual Map, Access Control, Monitoring, Devices, and Time &
Attendance). The BioStar system includes three preset administrator levels in addition to
custom administrator levels:
Administrator
Operator
Manager
Custom administrator levels

Administrators are capable of adding and configuring devices, users, doors, zones, and
access groups. They also can manage time and attendance functions, including setting up
time categories, daily schedules, shifts, holiday rules, and leave periods, as well as creating,
modifying, and viewing time and attendance reports. In addition, administrators can create
custom administrator levels that are granted various privileges for the BioStar system menus.
Operators can monitor and manage the BioStar system via a remote client terminal.
Operators have the same privileges with administrators, other than the privileges to create
and delete other administrator or operator accounts. Like administrators, operators are
capable of adding and configuring devices, users, doors, zones, and access groups. They also
can manage time and attendance functions, including setting up time categories, daily
schedules, shifts, holiday rules, and leave periods, as well as creating, modifying, and viewing
time and attendance reports.
Managers have privileges to read all information in the menus. However, they cannot create,
modify, or delete anything in the menus. Depending on your organizations requirements,
the capability to view events may be useful for other management purposes.
The custom administrator level can be assigned full or limited privileges on the seven
menus. On each menu, you can assign one of three privileges: All Rights, Modify, or Read.
Depending on your organizations requirements, the BioStar system can be managed more
effectively by adding custom administrator levels.
A typical setup will consist of one administrator (or more, depending on the size of your
organization) who has full access to the system. Below the administrator level, several
operators may perform various functions, such as remotely controlling doors and locks,
adding users, registering fingerprints, issuing access cards, adding access groups, defining
timezones, and configuring alarm events.
3.1.2 Add and Customize Administrative Accounts

By default, BioStar includes one administrator account, which is added when you install the
software (see section 2.3). You may choose to use this account as the sole administrator and
grant operator privileges to all other users who will manage the system or you may choose
to add multiple administrators to the system.
3.1.2.1 Add an administrative account

To add an administrative account:
1. From the menu bar, click Administrator > Admin Account to open the
Admin Account List dialog box.
2. Click Add New Administrator.
3. In the Add New Administrator dialog box, enter an Admin ID and password.
4. Confirm the password by retyping it and select an Admin Level from the drop-
down list:

Administrator: all privileges.

Operator: all privileges, other than creating or deleting administrator or
operator accounts.
Manager: privilege to read all information.
5. Click OK.
3.1.2.2 Change an administrative account level or password

If you accidentally set the wrong level for an administrative account or need to
change or reset a password, you can do so from the Administrator menu.
To change an administrative level or password:

2. Click an admin account in the list on the left side of the dialog box.
3. Click Modify Level/Password. This will open the Modify Administrator
dialog box.
4. Edit the account information as required:

To change the administrative level, choose a new level from the drop-
down list.
To change the password, type a new password in both the New Password
and Confirm boxes.
5. Click OK to save the changes.
3.1.2.3 Create a custom administration level

If you need to define a specific administrator role with particular privileges, you can
add a custom administrator level. You can allow full or limited access to any of
BioStars seven menus for the custom administrator level: User, Doors, Visual Map,
Access Control, Monitoring, Devices, and Time & Attendance.

The custom administrator level can be assigned privileges for specific users and
devices. A custom administrator will have the privileges you assign (All Rights,
Modify, or Read) only for those users or devices that you specify and will not be
allowed to view or modify other users or devices. While you are creating a custom
administrator level, in the User menu, you can grant privileges for users in a
department and its sub departments. However, ensure that you do not select
individual users, but rather the first-level or second-level departments they belong
to.
In the Device menu, you can grant privileges for specific devices. If a device has a
slave device connected, the privileges for the host device will also apply to the slave
device. Users and devices that are not selected in the User and Device menus will
not appear in the Doors, Visual Map, Access Control, Monitoring, and Time and
Attendance menus. If a door or zone is associated with devices that are not granted
privileges, the door or zone will not appear in the Door menu.
To create a custom administrator level:

2. Click Custom Level Setting.
3. From the Custom Level List dialog box, click Add Custom Level. This will
open the Add/Modify Custom Level dialog box.

4. Type a name for the custom level in the Name field.

5. If desired, add an additional description in the Description field.
6. Select a menu from the drop-down list.
7. When selecting the User Menu or Device Menu, select users or devices to
grant access privileges by clicking the checkboxes in the users or devices list.
8. Select a permission level (All Rights, Modify, or Read) by clicking the checkbox
next to an option.
9. Click Add to include the permission in the custom level.
10. Repeat steps 6-9 as necessary to add other permissions.
11. When you are finished customizing the level, click Save.
You can now create new administrative accounts with any of the custom
administrator levels you have created.
3.2 Setup Devices

This section describes how to use BioStar's device wizard to search for and add new devices,
as well as how to add 3rd party RF devices. In addition, the procedures that follow describe
basic configuration of devices within the BioStar system. For more information about
configuring devices, see sections 3.10.3 and 5.1.
3.2.1 Search for and Add Devices

BioStar includes a handy wizard for finding and adding devices. Before starting a search for
new devices, verify the device connections. If you have multiple devices to add, it may be
helpful to prepare a list of device locations, IDs, and IP addresses prior to adding them.
To search for devices and add them to the BioStar system:

1. Click Device in the shortcut pane.
2. In the Task pane, click Add Device.
3. When the wizard appears, click the radio button next to a connection type:
LAN: Choose this option to search for devices connected via Ethernet or Wireless
LAN.
Serial: Choose this option to search for devices connected to a client PC via RS485
and RS232 or slave devices connected via RS485 to another device that is
connected to a client PC (see section 3.2.2).
USB Device: Choose this option to search for devices connected via USB ports.
Note: BioStar versions 1.3 and higher include drivers for connecting BioStation
and D-Station devices via USB in Windows 7. These drivers will not work with

older versions of BioStar. If you are using an older version of BioStar be sure to
install the correct USB drivers.
Virtual USB Device: choose this option to search for virtual devices that you have
added to a USB drive.
4. Click Next.
5. For USB or Virtual USB searches, skip to step 7. If you are searching for devices
connected via LAN or serial ports, set advanced search criteria:
LAN: Select whether to search for devices using TCP or UDP protocols. When you
select TCP, you can specify an IP address range, the type of device you are
searching for (BioStation/D-Station/X-Station/BioStation T2/FaceStation: 1470,
BioEntry Plus/BioEntry W/BioLite Net/
Xpass/Xpass Slim: 1471, or Custom: enter manually), and the port to search with.
If you select UDP, you can search for devices only in the same subnet.
Serial: Specify a COM port (or select All port) and a baud rate. You can connect up
to 31 devices per COM port via RS485. If the RS485 cable is too long, the signal
may be weakened. In this case, you should install a terminating resistance at both
ends of the bus by turning on the Dip Switch on your device for normal signal
transmission. On the other hand, if the cable is too short, the resistance may
interrupt signal transmission. Therefore, by considering the length of the cable
and the signal status, select whether to turn on or off the terminating resistance
switch.
6. Click Next.
7. When BioStar completes the search, you can specify network settings as described
below. Click a device name in the list on the left and then configure the settings as
required:
Note: If you change the network settings for a device at this point, the device will be
removed from the device list. To add the device in the following steps, you must search for
the device again.
You need not and should not add devices with server mode. The devices will connect to the
server by themselves, and will be listed under the BioStar Server on the Device Tree dialog
box. If you are trying to add devices with server mode, the process will fail.
DHCP or Static IP: If you choose to use the DHCP option, the device will
automatically acquire network settings from the DHCP server. If you do not use
DHCP, you must configure the network settings manually.
Direct connection: This is the default connection option. With this option, the
BioStar client will connect directly to the device. If you choose this type of
connection, the BioStar client must be running to retrieve the log records from the
device.

Server connection: If you choose this option, the device will automatically
connect to the BioStar server. If you configure the server IP address and port
correctly, log records from the device will be gathered at the server, regardless of
whether or not the BioStar client is online. This option may also be useful if your
network configuration requires you to connect devices with private IP addresses
(for example, over a WAN) to a server with a public IP address. This option also
provides SSL encryption for BioStation devices.
8. Click Next.
9. Select the device or devices to add by clicking the checkboxes next to the device IDs.
10. Click Add to add the devices to the BioStar system.

11. Close the confirmation message that appears and click Finish to exit the wizard.
Note: You can manage devices by group by creating a tree hierarchy of named groups and
assigning devices into one of the groups. Groups are created by right-clicking on the desired
poision in the device tree and selecting Add Group. You can drag and drop devices between
different locations of groups. Groups can be nested four levels deep and a pair of host-slave
devices moves together.
3.2.2 Search for and Add Slave Devices

A distinctive feature of BioStar is that it supports host and slave devices in RS485 networks.
With this feature, only the host device must be connected to a PC via the LAN. The network
can then be easily expanded by adding slave devices via RS485 connections. This feature
also allows for controlling elevator (lift) access with Xpass and Xpass Slim devices that are
connected to LIFT I/O devices.
If your configuration includes slave devices, you must perform an additional search to locate
and add those devices.
First, configure the host device:
1. Search for and add the host device as described in section 3.2.1.

3. In the navigation pane, click the host device.

4. In the device pane, click the Network tab.
5. Change the RS485 serial setting by selecting Host from the Mode drop-down list.
6. Click Apply to save the change.
Next, search for and add slave devices:
1. In the navigation pane, right-click the host device and click Add Device (Serial). This
will open the Search and Add Device dialog box.
2. Click Next to begin the search.

3. When BioStar completes the search, click Next.
4. Select the device or devices to add by clicking the checkboxes next to the device IDs.
5. Click Add to add the device
6. Close the confirmation message that appears and click Finish to exit the wizard.
7. In the navigation pane, click the slave device.
8. In the device pane, click the Network tab.
9. Change the RS485 serial setting by selecting Slave from the Mode drop-down list.
10. Click Apply to save the change.
3.2.3 Add an RF Device

Prior to BioStar 1.2, third-party RF devices connected to Suprema devices (BioStation,
BioEntry Plus, BioEntry W, and BioLite Net devices), operated only as physical extensions to
the Suprema devices. As of BioStar 1.2, third-party RF devices connected to Suprema devices
function independently and can be associated with doors and included in zones.
To add an RF device:
1. Connect the RF device to a Suprema device.
2. Ensure that the Suprema device is added to the BioStar system (see section 3.2.1).


4. In the navigation pane, click the Suprema device name.
5. Click the Wiegand tab and specify Wiegand settings as described below.
b. Select Extended in the Wiegand Mode drop-down list.

c. Select Wiegand (Card) in the Wiegand Input drop-down list.
d. Click Apply at the bottom of the pane.
6. In the navigation pane, right-click the BioStation device name and then click Add RF
Device.
Note: For more information about using your third-party RF device, consult the user
guidance for the RF device. The Wiegand format must be configured properly to ensure
compatibility with third-party RF devices.
3.2.4 Connect a Device via Wireless LAN

Certain BioStation devices (BSTW-OC, BSTW-TC, BSRW-OC, BSRW-TC) and
BioStation T2, D-Station, FaceStation support wireless LAN connections.
To configure the settings for a wireless LAN connection:

2. Click a device name in the navigation pane.
3. Click the Network tab in the Device pane.
4. Select Wireless LAN in the Lan Type drop-down list.
5. Select one of the preset configurations in the WLAN section (Preset #1 ~
Preset #4).

6. Click Change Setting in the WLAN section. If you choose to use Preset #1 or
#2, the following figures will appear.
[Wireless LAN-supported BioStation models and D-Station]
[BioStation T2 and FaceStation]

7. Optional: If you choose to configure your own wireless LAN by selecting

Preset #3 or #4, then specify the following options.
Preset Name: Enter a name for the wireless LAN that the device will be
connected to.
ESSID: Enter the unique ID of the access point.
Network Authentication: Select a network authentication mode from the
drop-down list (Open System, Shared Key, or WPA-PSK). The authentication
mode must be the same for the device and the access point.
Encryption Strength: Select an encryption strength from the drop-down
list (available options depend on network authentication setting).
Network Key: Enter the network key. _suprema_wpa_ is a pre-defined
value for Preset #1 networks (biostation_wpa, biostar_wpa), and
_suprema_wep_ is for Preset #2 networks (biostation_wep, biostar_wep).
Confirm Key: re-enter the network key.
8. Click OK to save your changes.
3.2.5 Configure a BioStation Device

This section provides an overview of configuring BioStation devices to work with the BioStar
software. For more information, refer to the installation guides that accompany your devices.

To configure a BioStation device:

2. Double-click a BioStation device name in the navigation pane. This will open a Device
pane similar to the one below:
3. Configure device information on the following tabs. For an explanation of device

settings, please see section 5.1.1.
Operation mode: Use this tab to set the device time or retrieve it from a host PC
and adjust settings for operation modes.
Fingerprint: Use this tab to specify security, quality, matching, and timeout
settings for fingerprint recognition.
Network: Use this tab to specify settings for LAN or serial connections.
Access Control: Use this tab to specify entrance limits and default access groups
for an individual device.
Input: Use this tab to add, modify, or delete input settings for the device.
Output: Use this tab to add, modify, or delete output settings for the device.
Black List: Use this tab to block access through a particular card, e.g. a card which
has been stolen or used by a former employee. You can use this feature only when
the card mode of the device is set to 'Template on Card'. Adding a user ID or card
ID denies access from the users with the matching ID or card.
Display/Sound: Use this tab to adjust display or sound settings and add
background images and sounds.
T&A: Use this tab to configure time and attendance settings.
Wiegand: Use this tab to configure the Wiegand format. For more information
about Wiegand formats, see section 3.2.133.
4. When you are finished configuring the device, click Apply to save your changes.

5. To apply the same settings to other devices, click Apply to Others and select other
devices from the Device Tree dialog box.
3.2.6 Configure a BioEntry Plus or BioEntry W Device

To configure a BioEntry Plus or BioEntry W device:
2. Double-click a device name in the navigation pane. This will open a Device pane similar
to the one below:

settings, see section 5.1.2.
Operation mode: Use this tab to set the device time or retrieve it from a host PC,
adjust settings for operation modes, and adjust options for fingerprint
recognition.
Access Control: Use this tab to specify entrance limits, access groups, and time
and attendance mode settings.
Input: Use this tab to add or modify inputs to the device.
Output: Use this tab to add or modify outputs from the device.

Command Card: Use this tab to issue command cards that can control BioEntry
Plus or BioEntry W devices. For more information about issuing command cards,
see section 3.2.6.1.
Display/Sound: Use this tab to configure LED & Buzzer settings according to the
event or status.
3.2.6.1 Issue command cards

Command cards allow you to enroll and delete users directly from a BioEntry Plus
or BioEntry W device. For more information about enrolling users via command
cards, see section 3.6.2.3. For more information about delete an individual or all
users via command cards, see section 4.5.1.1 and 4.5.1.2.
To issue command cards:

2. In the navigation pane, click the name of a BioEntry Plus or BioEntry W device.
3. Click the Command Card tab in the Device pane.
4. Click Read Card.

5. Place a command card on the device.

6. Select a command type from the drop-down list.

7. If desired, set the command card to require administrator authentication by
clicking the checkbox next to the option.
8. Click Add.
3.2.7 Configure a BioLite Net Device

To configure a BioLite Net device:
to the one below:

adjust settings for operation modes, and adjust options for fingerprint
recognition.
Access Control: Use this tab to specify entrance limits and access groups.

Display/Sound: Use this tab to configure LED & Buzzer according to the event or
status.
5. To apply the same settings to other devices, click Apply to Others, select other devices
from the Device Tree dialog box, and click Apply.
3.2.8 Configure an Xpass or Xpass Slim Device

To configure an Xpass or Xpass Slim device:
to the one below:

settings, see section 5.1.4 (Xpass) or 5.1.5 (Xpass Slim).

adjust settings for operation modes, and adjust settings for card ID formats. Xpass
Slime devices do not support the Mifare template cards.
Access Control: Use this tab to specify entrance limits and access groups.
Command Card: Use this tab to issue command cards that can control Xpass or
Xpass Slim devices. For more information about issuing command cards, see
section 3.2.8.1.
Display/Sound: Use this tab to configure LED & Buzzer according to the event or
status.
5. To apply the same settings to other devices, click Apply to Others, select other devices
from the Device Tree dialog box, and click Apply.
3.2.8.1 Issue command cards

Command cards allow you to enroll and delete users directly from an Xpass or
Xpass Slim device. For more information about enrolling users via command cards,
see section 3.6.2.3. For more information about deleting an individual or all users
via command cards, see section 4.5.1.1 and 4.5.1.2.
To issue command cards:

2. In the navigation pane, click the name of an Xpass device.
3. Click the Command Card tab in the Device pane.

4. Click Read Card.

5. Place a command card on the device.
6. Select a command type from the drop-down list.
7. If desired, set the command card to require administrator authentication by
clicking the checkbox next to the option.
8. Click Add.
3.2.9 Configure a D-Station Device

To configure a D-Station device:
to the one below:


Camera: Use this tab to assign events, by timezone, that can be performed via the
camera and the face detection feature.

3.2.10 Configure an X-Station Device

To configure an X-Station device:
to the one below:


3.2.11 Configure a BioStation T2 Device

To configure a BioStation T2 device:
to the one below:


Interphone: Use this tab to set the device to act as an interphone which allows
communication between people on either side of the door.


3.2.12 Configure a FaceStation Device

To configure a FaceStation device:
to the one below:

Face Use this tab to specify security level and enrollment sensitivity settings for
face recognition.
Interphone : Use this tab to set the device to act as an interphone which allows

3.2.13 Change Wiegand Formats

From the BioStar interface, you can configure the Wiegand format of a device to control
device inputs and outputs.
To configure the Wiegand format:

2. In the navigation pane, click a device name.
3. Click the Wiegand tab in the Device pane.
4. Click Change Format. This will open the Wiegand Configuration wizard.
5. Click a radio button to select one of the following formats:
26-bit Standard: This format is the most widely used and consists of an 8-bit FC
code and a 16-bit ID. You cannot change the bit definition of the format or the
parity bits of this format.

Pass-through: Use this format to customize only the ID bits. During verification, if
the ID is recognized, the Wiegand input string will pass through in its original
form. You cannot set the parity bits or alternative values of this format. By
definition, the pass-through format is useful only when the operation mode is
one-to-one (1: 1). In one-to-many (1: N) mode, non-ID bits are set to 0.
Custom: With a custom format, you can define the ID bits, parity bits, and
alternative values.
6. Use the Wiegand Configuration wizard to customize the Wiegand format to your
specifications (see the subsections that follow for more information).
7. When you have completed making changes with the wizard, click Apply to save your
changes.
3.2.13.1 Configure a 26-bit Wiegand format

When you select a 26-bit format, the only thing you can customize is the FC Code:
1. After selecting the format in the wizard, click Next until you reach the
Alternative Value dialog box.
2. Click the FC Code checkbox and enter a new FC Code.

3. Click Finish to close the wizard.

3.2.13.2 Configure a pass-through Wiegand format

When you select a pass-through format, you can alter the total number of bits and
assign the ID bits:
1. After selecting the format in the wizard, click Next to advance to the
Wiegand Configuration - Format dialog box.
2. If desired, enter a new total number of bits and click Apply.

3. Click the User ID button (I) on the right.
4. Assign ID bits by clicking the appropriate squares.
5. Click Next until you reach the Wiegand Configuration - Alternative Value
dialog box.
3.2.13.3 Configure a custom Wiegand format

It is able to change entire bit numbers and parity bit numbers, allocate ID bit and
custom ID bit section, define parity bit, and set alternative values for specific output
data section by selecting user custom Wiegand type.
Configure a custom Wiegand format
1. After selecting the format in the wizard, click Next to advance to the
Wiegand Configuration - Format dialog box.
2. If desired, enter a new total number of bits and click Apply.

3. If parity settings have changed, click the Reset parity button.

4. Click the User ID button (I) on the right and assign ID bits by clicking the
appropriate squares.
5. Click the Custom ID button on the right, and then click the square, and set the
area for custom ID bit.
6. Click the Even Parity button (E) on the right and assign an even parity bit by
clicking on the appropriate squares.
7. Click the Odd Parity button (O) on the right and assign an odd parity bit by
clicking on the appropriate squares.
8. Click Next.
9. In the Wiegand Configuration - Parity dialog box, select the bits that will be
used to calculate the first parity bit.
10. As necessary, click >> and select the bits that will be used to calculate
additional parity bits. You must perform this step for each parity bit you
assigned in steps 4 and 5. If necessary, you can click Initialize to reset the
selection.
11. Click Next.
12. In the Wiegand Configuration - Alternative Value dialog box, select a field
to customize (non-ID bits only).
13. Click the Alt Value checkbox and enter a new value for the output string.
14. Repeat steps 10-11 as necessary to customize the rest of the output string.

3.3 Setup Doors

This section describes how to setup doors within the BioStar system. For information about
installing physical devices and integrating them with door components, refer to the user
guide that accompanies each device.
3.3.1 Add a Door

To add a door:
1. Click Doors in the shortcut pane.
2. In the task pane, click Add New Door.
3. Right-click New Door, click Rename, and type a name for the door.
3.3.2 Associate a Device With a Door

BioStar allows you to associate a maximum of two devices with each door. When using two
devices on a door, the devices should be connected to each other via RS485. See section 5.2
for an explanation of door settings.
To associate a device with a door:

2. Right-click a door and click Add Device.
3. Select a device from the Device Tree dialog box by clicking the checkbox next to a
device name.
4. Click OK.

3.3.3 Configure a Door

2. Click the name of a door in the navigation pane. This will open a Doors pane similar to
the one below:
3. Configure door information on the following tabs. For an explanation of door settings,
see section 5.2.
Details: Use this tab to control the interaction between doors, devices, locks, and
exit buttons. If you add two devices to a door, you can also use this tab to
configure anti-passback settings.
Alarm: Use this tab to specify what actions to take when the door is forced open
or held open.
Zone: Use this tab to see the zones associated with a door.
Access Control: Use this tab to see the access groups associated with a door.
Event: Use this tab to retrieve and monitor an event log for the door.
3.3.4 Create a Door Group

You can create groups of doors for easier management.
2. In the navigation pane, right-click Doors and click Add Door Group.
3. Type a name for the group and press Enter.
4. To add a door to the group, click and drag a door to the group.

3.4 Setup Elevators (Lifts)

This section describes how to setup elevators within the BioStar system. For information
about installing physical devices and integrating them with elevator components, refer to
the user guide that accompanies each device. BioStar supports up to 128 elevators (lifts).
3.4.1 Add an Elevator

To add an elevator:
1. Click Lift in the shortcut pane.
2. In the task pane, click Add New Lift.
3. Right-click New Lift, click Rename, and type a name for the elevator.
3.4.2 Associate a Device With an Elevator

BioStar allows you to associate Xpass or Xpass Slim devices with a LIFT I/O device to control
access to elevators. The LIFT I/O device must be connected to the Xpass or Xpass Slim device
via RS485.
To associate an Xpass or Xpass Slim device with an elevator:

1. Click Lifts in the shortcut pane.
2. Right-click an elevator name and click Add Reader.
3. Select an Xpass or Xpass Slim device from the Device Tree dialog box by clicking the
checkbox next to a device name.
4. Click OK.

3.4.3 Configure an Elevator

2. Click the name of an elevator in the navigation pane. This will open a Lifts pane similar
to the one below:
3. Configure elevator information in the following fields:

LIFT IO: Select a LIFT I/O device to view and change settings.
Relay Duration: Relay Duration is supported in the Detail tab of Lift IO. Default
setting range is 10 seconds, and you can set min. 1 second to max. 60 seconds.
Supported by latest regular firmware among Xpass and BioEntry Plus supporting
LIFT IO.
Note: Supported Firmware Versions: BioEntry Plus 1.6, Xpass 1.3
OUTPUT: This field lists the avaialble outputs of the LIFT I/O device.
Floor: Use this tab to see the zones associated with a door.
Not use: Select the checkbox when you do not use the output port of the LIFT I/O
device. Clear the checkbox to control aceess to floors by associating outputs with
floors.
4. When you are finished configuring the elevator, click Apply to save your changes.
3.4.4 Add Users to an Elevator


2. Click the name of an elevator in the navigation pane.

3. Click Lift Manage Users in the shortcut pane. This will open the Lift Manage User
dialog box.
4. In the left pane, click a users name.

5. In the right pane, click the checkboxes next to floors that you wish to assign the user to.
6. Click Apply to save your chagnes.
3.4.5 Transfer Settings to an Elevator
!
Attention: When using Xpass or Xpass Slim devices as lift readers, transferring settings
to the device with the User menu will reset all of the settings and user data stored on the
device. To preserve the settings, use the Transfer to Device function in the Lift menu
instead.
To send settings and user data to an Xpass or Xpass Slim device:

2. Click Transfer to Device in the task pane. This will open the Lift Tree dialog box.

3. In the lift tree, select a device or devices by clicking the checkboxes next to device
names.
4. Click Apply to send the elevator settings to the selected devices.
3.5 Setup Zones

BioStar allows you to provide sophisticated access control with multiple zones. Zones can be
used to control the behavior of devices, doors, and other components. In addition, zones
can be configured to provide different types of restrictions, such as anti-passback, timed
anti-passback, and entrance limits. The sections below describe how to determine which
zones to use and how to add and configure zones.
3.5.1 Determine Which Zones to Use

In total, the BioStar system supports seven types of zones:
Access zone: Use this zone to synchronize user or log information. If you select the user
synchronization option, user data enrolled at the devices will be automatically
propagated to other connected devices. If you select the log synchronization option, all
log records will be written to the master device (in addition to the server), so that you
can check log records of member devices. For information about customizing access
zones, see section 5.3.5.
Anti-passback zone: Use this zone to prevent a user from passing his or her card back
to another person or using his or her fingerprint to allow someone else to gain entry.
The zone supports two types of anti-passback restrictions: soft and hard. When a user
violates the anti-passback protocol, the soft restriction will record the action in the
user's log. The hard restriction will deny access and record the event in the log when the
anti-passback protocol is violated. For information about customizing anti-passback
zones, see section 5.3.1.

Entrance limit zone: Use this zone to restrict the number of times a user can enter an
area. The entrance limit can be tied to a timezone, so that a user is restricted to a
maximum number of entries during a specified time span. You can also set time limits
for reentry to enforce a timed anti-passback restriction. For information about
customizing entrance limit zones, see section 5.3.2.
Alarm zone: Use this zone to group inputs from multiple devices into a single alarm
zone. Devices in the alarm zone can be simultaneously armed or disarmed via an arm or
disarm card or a key. For more information about configuring alarm zones, see sections
3.5.2.4, 3.5.2.5, 3.5.2.6 and 5.3.3.
Fire alarm zone: Use this zone to control how doors will respond during a fire. External
inputs can be fed into the BioStar system to automatically trigger door releases or
perform other actions. For more information about customizing fire alarm zones, see
section 5.3.4.

Muster zone: Use this zone to monitor and track employees during an emergency or to
perform a roll call where employees are required to be present in a particular area at a
particular time. Muster zone allows administrators to determine if any employee has not
reported to the muster area and, if any employee is unaccounted for, take the necessary
actions to locate them. For more information about customizing muster zone, see
section 5.3.6.
Interlock zone: Use this zone to create an interlock area with two doors equipped with
devices. When an external input indicates that one door is open, the other door is
automatically locked to provide a secure interlock area. A reader-equipped door that
does not belong to any other zone can be used to create up to four interlock zones
(four zones maximum per reader). For more information about configuring an interlock
zone, see section 5.3.7.
3.5.2 Add and Configure Zones

When you add a zone, you can use the four tabs in the Zone pane to configure the zone. For
an explanation of zone settings, see section 5.3.
Details: Add devices and specify inputs or other parameters for a zone.
Alarm: Specify alarm actions and outputs.
Access Group: Apply access groups to a zone (not available for fire alarm zones).
Event: View events associated with a zone.
3.5.2.1 Add a zone

To add a new zone:
2. In the navigation pane, right-click Zone.
3. Click Add Zone.
4. Type a name for the zone in the Name field.
5. Select a zone type from the drop-down list (see section 3.5.1 for zone
descriptions).
6. Press OK. The Zone pane will appear on the right side of the screen.

3.5.2.2 Add a device to a zone

To implement the protocols of a zone, you must associate devices with the zone.
The Details tab (in the Zone pane) contains a Device List that shows each device
associated with a zone (see below).
To add a device to a zone:

2. In the navigation pane, click the name of a zone.
3. In the Zone tab, at the bottom of the Device List, click Add Device. This will
open the Add Device dialog box.
4. Select a device (or multiple devices) from the list and click >.
Anti-passback zones: When the Select Zone Attribute pop-up appears,
select an attribute from the drop-down list (In Device or Out Device).
Alarm zones: When the Select Zone Attribute/Type pop-up appears,
select a device attribute from the drop-down list (General, Arm, Disarm, or
Arm/Disarm). If you select an arm or disarm attribute (or Arm/Disarm),
click the Card or Key radio button to specify how to arm or disarm zones,
and then press OK. For more information about arming or disarming
zones, see section 3.5.2.5.
5. Press Save to add the devices to the list.

3.5.2.3 Configure zone inputs

When adding devices to an alarm or fire alarm zone, you must also configure the
zone inputs.
To configure inputs:
2. In the navigation pane, click the name of a zone.
3. In the Zone tab, at the bottom of the Device List, click Add Input. This will
open the Add Zone Input dialog box.
4. Type a name for the input in the Name field.

5. Select a device from the drop-down list.
6. Select one of the available inputs by clicking the checkbox next to the
appropriate input.
7. Select the normal position of the input (N/O-normally open or N/C-normally
closed).
8. Set the duration (in milliseconds) of the input signal.
9. Click OK to add the input to the Input List.
3.5.2.4 Configure alarm actions and outputs

Configure alarm actions to specify what alerts to receive, if any, and which ports
and relays to use for alarm outputs. The Alarm tab (in the Zone pane) offers the
following options for all zones except access zones. For more information about
alarms, see sections 3.5.2.5 and 3.10.
Program Sound: Set a sound to be emitted by the software (at the host
computer or BioStar Server). To add custom sounds, please see section
3.10.1.2.
Device Sound: Set a sound to be emitted by a particular device.

Send Email: Create an email alert to send when an alarm is activated and
select recipients or email alerts. For more information about email alerts,
see section 3.10.2.
Output Device: Specify a device that will send an alarm signal to an external
device, such as an alarm siren.
Output Port: Specify the port to use for an output signal.
Output Signal: Specify a type of output signal.
3.5.2.5 Configure arm and disarm settings

After adding an alarm zone, you can configure the actions that will arm and disarm
the zone.
To configure arm and disarm settings:

2. In the navigation pane, click the name of an alarm zone.
3. Click the Details tab in the Zone pane.
4. Click Setup to the right of Arm/Disarm Type. This will open the Arm/Disarm
Setting dialog box.
5. To configure cards for arming or disarming zones:

a. Select a device from the Read Device drop-down list.
b. Click Read Card. The LED on the device you selected will begin to flash.
c. Place the card on the device.
d. When the card has been read, click Add. The card can now be used to
arm or disarm devices in the alarm zone.
6. To configure device keys for arming or disarming zones (BioStation devices
only):
a. Select a key that will arm devices from the first drop-down list.
b. Select a key that will disarm devices from the second drop-down list.
7. When you are finished configuring the arm and disarm settings, click OK.

3.5.2.6 Configure external input/output settings

Instead of manually arming or disarming alarm zones, you can configure the
BioStar system to automatically determine when to arm or disarm alarm zones
based on the status of a specified input. You can also prevent the BioStar system
from arming an alarm zone when a monitored input is in a not-ready position.
Finally, you can configure the system to send a specified signal to an external
output when it arms or disarms alarm zones. External input/output settings are
available in BioStation V1.8, BioEntry Plus V1.4, BioEntry W V1.0, BioLite Net V1.2,
Xpass and Xpass Slim V1.0, D-Station V1.0, X-Station V1.0, BioStation T2 and
FaceStation V1.0 or higher.
To configure external input/output settings:

2. In the navigation pane, click the name of an alarm zone.
3. Click the Details tab in the Zone pane.
4. Click Setup to the right of External Input/Out. This will open the External I/O
Setting dialog box.
5. Configure the following input/output settings as desired:

To prevent the BioStar system from arming an alarm zone:
a. Under External Sensor Status, select a device from the Device drop-down
list.
b. Select an input from the Input drop-down list.
c. Select the position of the input (N/O normally open or N/C normally
closed) that will prevent the system from arming the alarm zone.
To allow the BioStar system to automatically arm or disarm an alarm zone:

a. Under External Arm/Disarm, select a device from the Device drop-down

list.
b. Select an input from the Input drop-down list.
c. Select the position of the input (N/O normally open or N/C normally
closed) that will allow the system to arm the alarm zone. The other
position will allow the system to disarm the alarm zone.
To send an arm signal to an external device, such as an alarm signal:
a. Under Arm Status, select a device from the Device drop-down list.
b. Select a relay from the Relay drop-down list.
c. Select a type of signal from the Signal drop-down list.
d. Specify a priority level in the Priority field.
To send a disarm signal to an external device, such as an alarm signal:
a. Under Disarm Status, select a device from the Device drop-down list.
b. Select a relay from the Relay drop-down list.
c. Select a type of signal from the Signal drop-down list.
d. Specify a priority level in the Priority field.
6. When you are finished configuring the external input/output settings, click
OK.
3.5.2.7 Select access groups

The Access Group tab (in the Zone pane) allows you to specify access groups that
can bypass the normal restrictions set for the zone. For example, you may choose a
particular access group to be exempt from the restrictions of an anti-passback
zone. For alarm zones, this tab allows you to specify access groups that can arm
and disarm alarms. To select an access group, please click the checkbox next to a
group name and then click Apply.
3.5.2.8 View zone events

The Event tab (in the Zone pane) provides a listing of log events for a particular
zone. You can set a date range with the drop-down calendars and view a report of
events by clicking Get Log. For more information about monitoring and viewing
event logs, see section 4.1.
3.6 Setup Users

You will need to use a fingerprint scanner to capture each user's fingerprints. For this reason,
it may be helpful to have a terminal connected to the system at a registration center, such as
a human resources or security office. BioStation, BioEntry Plus, BioEntry W, BioLite Net, or D-
Station devices can be used for fingerprint scanning when networked to the BioStar server,
or the BioMini USB device can be connected directly to a BioStar client to provide
convenient fingerprint scanning at a registration location.

When adding users, you will first need to create a user account. Once the account has been
created, you can register fingerprints and access cards or edit user details as desired.
3.6.1 Create a User Account

User data is controlled via a user account. You can create new accounts for users or retrieve
user data from a device. To retrieve user data from a device, please see section 3.6.5.3. To
migrate user data from an existing BioAdmin database, see section 2.4.
To create new user accounts:

1. Click User in the shortcut pane.
2. In the navigation pane, right-click User or a department name and click Add User. This
will open a User pane similar to the one below.
3. Add details of the user's account in the User pane:

Name: Enter the users name.
Department: Enter a department or click the ellipsis button (...) to select from
departments you have added to the BioStar system.
Telephone: Enter the users telephone number (digits onlyno characters are
allowed in this field).
E-mail: Enter the users email address.
Password: Enter the users password, if desired.
Note: Passwords saved in FaceStation devices are not compatible with other

devices. When transferring data from a FaceStation device to another type of

device, you must create new passwords for the other device.
Admin Level: Select the users BioStar administration level (Normal User or Admin
User).
ID: Enter an identification number for the user.
Start Date: Set a beginning date that the user can obtain authorization via the
BioStar system.
Expiry Date: Set a date that the user's account will expire (you can also specify
the hour that the account will expire).
Title: Select a title for the user (Guest, President, Director, General Manager, Chief,
Assistant Manager, or custom title).
Mobile: Enter a mobile telephone number for the user.
Genders: Select the user's gender.
Date of Birth: Select the user's date of birth from the drop-down calendar.
Note: You can add a photo of the user or a private message by clicking Modify Private
Information.
4. Register fingerprints (see section 3.6.2), face images (see section 3.6.3), and access
cards (see section 3.6.4) as necessary.
5. When you are finished adding details to the users account, click Apply.
3.6.2 Register Fingerprints

BioStar provides an option for encrypting fingerprint templates. If you choose to use this
option, you should set the encryption before capturing fingerprint scans. Any previously-
captured fingerprint templates will be rendered unusable when you activate the encryption.
For more information about encrypting fingerprints, see section 4.7.
When registering fingerprints, it is important to capture quality images. Before registering
fingerprints, ensure that the candidate's fingers are clean and dry. You may need to ask the
candidate to clean his or her fingers just prior to registration. If a candidate has excessively
dry skin, ask him or her to moisten the fingertips slightly by breathing warm air on them just
prior to registration.
When registering fingerprints, keep the following tips in mind:
You must register the same finger twice (two templates). You can register a total of two
fingers (a total of four templates) per user.
Fingers with scars, worn fingerprints, or other physical damage may be poor choices for
registration.
It may be necessary to delete and recapture an image of a fingerprint if the candidate
experiences low acceptance rates.

3.6.2.1 Place fingers on the sensor

To ensure good quality fingerprints, candidates must place as much of the finger
pad (the soft part opposite the fingernail) on the sensor as possible. Suprema
recommends using index or middle fingers, because they are typically easier for
users to correctly place on the sensor. To properly place a finger on the sensor,
candidates should lay the finger flat, so that the pad side covers most of the sensor
and the finger is nearly perpendicular to the sensor.
The image below illustrates both correct and incorrect placement of a finger on the
sensor.
3.6.2.2 Register fingerprints

BioStar allows you to register up to ten fingerprints per user. However, some
devices can only store a limited number of fingerprints:
Device Number of Fingerprints
BioEntry Plus 2
BioEntry W
BioLite Net
BioStation 5
BioStation T2 10
D-Station
When fingerprints are distributed from BioStar, the device will receive the maximum
number of fingerprints, beginning with the first stored fingerprint scan.
If desired, one of the fingerprints can be used as a duress signal that will trigger
alarms when a candidate is forced to access an area. When registering duress
fingerprints, keep the following tips in mind:
A duress finger cannot be used for normal access
The duress finger should appear to be a natural choice (i.e., the little finger is
an unusual choice and may indicate to a perpetrator that the candidate is
triggering an alarm)
Candidates should be educated about what occurs when the duress finger is
used (e.g., the duress finger may trigger automatic door locks or silent
alarms).

To register fingerprints:
2. In the navigation pane, click a users name.
3. Click the Fingerprints tab in the User pane.
4. Select the device you will use for scanning fingerprints from the Enroll Device
drop-down list.
5. Select a security level from the 1: 1 Security Level drop-down list.
6. Specify any of the following options, as desifred:
Enroll Quality: Set the quality of fingerprints to be enrolled to increase
authentification efficiency. The quality of a fingerprint is determined by
multiple factors incluing data on its minutiae distribution. You can specify
four values (20, 40, 60, 80) and selecting the higher numbers will improve
the quality of a fingerprint but can reduce the chances of a fingerprint
being enrolled. Please note that this option is only avaiable on BioStar
Standard Edition.
Show Fingerprint Image: Specify whether to display a fingerprint image
on the screen. Fingerprint images are not saved in the database of BioStar
server and you can only save individual images on your PC if necessary.
7. Click Add at the bottom right of the User pane to create an empty slot for
registering a fingerprint.
8. In an empty finger slot, press Scan and then have the user place his or her
finger on the scanner twice, as prompted by the BioStar interface.
9. If desired, click the checkbox next to the Duress option to set this fingerprint
as the duress signal.
10. Repeat steps 6-8 to register the rest of fingerprints.
11. Click Apply to save your changes.
12. Validate the submitted fingerprints by clicking either one or both of the
following two options:
Verification Test: Compare a newly-scanned fingerprint to only the
stored fingerprint templated collected from a prior enrollment.

1: N Auth Test: Match a newly-scanned fingerprint against multiple

fingerprint templates stored in the server.
3.6.2.3 Enroll users via command cards

After issuing command cards, you can enroll users directly from a BioEntry Plus,
BioEntry W, or Xpass device. For more information about issuing command cards,
please see section 3.2.6.1 and 3.2.8.1.
To enroll a user on a BioEntry Plus or BioEntry W device via a command card:

1. Place an enroll card (command card) on a BioEntry Plus or BioEntry W device.
2. If authorization is required, an administrator must scan his or her fingerprint
to continue.
3. To capture only fingerprints, have the user place his or her finger on the
scanner two times (as prompted by the device).
4. To capture fingerprints and issue an access card, place the card on the device
first. Then, have the user place his or her finger on the scanner two times (as
prompted by the device).
To enroll a user on an Xpass device via a command card:

1. Place an enroll card (command card) on an Xpass device.
2. If authorization is required, an administrator must place his or her access card
on the device to continue.
3. Place the users access card on the device.
4. Place the enroll card again on the device to confirm the action.
3.6.3 Capture Face Images

With camera-equipped devices, such as the D-Station and FaceStation, you can capture
images of users faces and use those images for authentication via BioStars face detection
technology. BioStar matches a still image of the users face during authentication with
captured face images in the BioStar server database. Face detection can be used
simultaneously with fingerprint recognition for highly secure biometric access control. For
more information about face detection settings, please see section 5.4.3.

To capture face images with FaceSation devices:

3. Click the Face tab in the User pane.
4. Select the Enrollment Device you will use for capturing face images from the drop-
down list.
5. Click Add at the bottom right of the screen to add face(from the 1st Face to the 5th
Face).
Note: FaceStation supports up to 5 different user faces to ensure the most accurate face
detection at all times, regardless of the different hair styles, make-ups or eye glasses the user
might wear.
6. Click the newly added face, click Capture, then follow the instructions prompted by the
enrollment device. Repeat steps 5~6 to add more faces.
7. Click Use Profile Img to use the currently registered and selected face image as the
users profile image in the User pane.

To capture face images with D-Station devices:

3. Click the Face (Fusion) tab in the User pane.
4. Select the enrollment device you will use for capturing face images from the drop-
down list.
5. In the 1st Face section, click Capture, and then have the user align his or her face with
the camera, as prompted by the device.
6. If desired, click Use Profile Img to use the image assigned to the users profile instead
of capturing a new image.
7. Repeat steps 5-7 in the 2nd Face and 3rd Face sections to capture additional face
images.
3.6.4 Issue Access Cards

Suprema manufactures access control devices that support multiple types of access cards, as
listed below:
EM4100: BioStation, BioEntry Plus, and BioLite Net
MIFARE: BioStation Mifare, BioEntry Plus Mifare, BioEntry W Mifare, BioLite Net, D-
Station, and FaceStation
iCLASS: BioEntry Plus iCLASS
FeliCa: BioEntry Plus iCLASS
HID proximity: BioStation HID and BioEntry Plus HID

EM4100 and HID cards require only a card ID to complete card registration, while MIFARE
and iCLASS cards support two operation modes: Card Serial Number (CSN) and Template-
on-Card modes. FeliCa cards support only the CSN mode. When using the CSN mode, you
can read the serial number just as you would for an EM4100 or HID card. When using
Template-on-Card mode, you must record the user information, including fingerprint
templates, directly to the card.
Follow the procedures below to issue the appropriate type of card and then add it to the
user's account.
3.6.4.1 Issue EM4100 cards

To register a EM4100 card for a user:
2. In the navigation pane, click a user's name.
3. In the User pane, click the Card tab.
4. Select a EM4100 from the Card Type drop-down list.
5. Click Card Management. This will open the Card Management dialog box.
6. Select a Device ID from the drop-down list.

7. Enter a card ID (32 bits) and custom ID (8 bits) either manually or by reading
from the card (you can also click Use User ID to insert the users ID in these
fields):
To enter the data manually, type the card ID and custom ID in the
corresponding fields, click OK, and then skip to step 8.
To read the data from the card, click Read Card (the LED on the device
you selected will begin flashing) and then place the card on the device.
After the card has been read, click OK.
8. Click Apply to save the card to the user's account.
3.6.4.2 Issue HID proximity cards

To register a HID proximity card for a user:


4. Select HID Prox from the Card Type drop-down list.
6. Select a Device ID from the drop-down list.

7. Enter a card ID and facility code (FC) either manually or by reading from the
card (you can also click Use User ID to insert the users ID in these fields):
To enter the data manually, type the ID and facility code in the
To read the data from the card, click Read Card (the LED on the device you
selected will begin flashing) and then place the card on the device. After
the card has been read, click OK.
3.6.4.3 Issue FeliCa cards

To register a FeliCa card for a user:
4. Select FeliCa from the Card Type drop-down list.
6. Select a device or Smart Card Reader from the Device ID drop-down list.

7. Enter a card ID and custom ID either manually or by reading from the card
(you can also click Use User ID to insert the users ID in these fields):
To enter the data manually, type the card ID and custom ID in the
3.6.4.4 Issue MIFARE or iCLASS CSN cards

MIFARE and iCLASS CSN cards work much like EM4100 and HID cards, in that they
store an uneditable card serial number (CSN) for a user.
To register a card for a user:

4. Select Mifare CSN or iCLASS CSN from the Card Type drop-down list.
6. Select a Device ID or Smart Card Reader from the drop-down list.

7. Enter a card ID either manually or by reading from the card (you can also click
Use User ID to insert the users ID in these fields):
To enter the data manually, type the ID and facility code in the
8. Click Apply to issue the card to the user's account.

3.6.4.5 Issue MIFARE or iCLASS template cards

MIFARE and iCLASS template cards allow you to store user information and
fingerprint templates directly on the card.
To register a card for a user:

4. Select Mifare Template or iCLASS Template from the drop-down list.
6. Select a Device ID or USB MIFARE device (if connected) from the drop-down
list.
7. If desired, click Bypass Card to allow the user to bypass the fingerprint
authentication.
8. Click Read Card. The LED on the device that you selected will begin flashing.
9. Place the card on the device.
10. After the card is read, click OK.
11. Click Apply to issue the card to the user's account.
Note: iCLASS 2000, 2002 and 2004 cards are not supported as template cards.
3.6.4.6 Change the MIFARE or iCLASS site key

Data encryption for MIFARE and iCLASS cards is governed by a 48-bit site key. Only
those cards with appropriate site keys can be read by connected devices. BioStar
allows you to define up to two MIFARE and iCLASS site keys (primary and
secondary), so that you can change the site key for existing cards.

Note: This feature is only supported for template-on-cards. Also, please note that
site keys must be carefully guarded. If the site key is revealed, your security system
can be bypassed.
To change the MIFARE or iCLASS site key:

1. From the menu bar, click Option > Mifare Card or iCLASS Card > Mifare
Sitekey or iCLASS Sitekey . This will open the Mifare Sitekey or iCLASS
Sitekey dialog box.
2. Enter a new primary key in the New Primary Key field.

3. Enter the key again in the Retype Primary Key field.
4. Click the Use radio button to activate the secondary key function. This allows
cards with the old site key to be read and rewritten with the new key:
a. Enter the old site key in the New Secondary Key field.
b. Enter the old site key again in the Retype Secondary Key field.
5. When you are finished editing the site key, click OK.
Note: When all cards have been rewritten with the new site key, Suprema advises
disabling the secondary key function to prevent old cards from being used for
access.
3.6.4.7 Edit the MIFARE layout

BioStar allows you to customize the layout that is used to record user information
and fingerprint templates. This layout will be applied to all new MIFARE cards
issued with the devices you specify (BioStation Mifare, BioEntry Plus Mifare,
BioEntry W Mifare, BioLite Net, D-Station, or FaceStation devices).
MIFARE 1K cards are organized into 16 sectors with 4 blocks of 16 bytes each.
MIFARE 4K cards are organized into 32 sectors with 4 blocks and 8 sectors with 16
blocks. The following constraints apply to the MIFARE layout:
The first sector (block 0 through block 3) is reserved and cannot be used for
other data.

The last block of each sector (blocks 3, 7, 11, and so on) is reserved for site
key information.
The card information sector (CIS) occupies three contiguous blocks and
should start at the first available block of a sector (blocks 4, 8, 12, and so
on).
There should be no overlap between each templates data.
To edit the MIFARE layout:

1. From the menu bar, click Option > Mifare Card > Mifare Layout. This will
open the Mifare Layout dialog box.
2. Use the drop-down lists and input fields to configure the following
parameters of the MIFARE layout:
CIS Index Block: Select the block index to use for header information (4,
8, 12, or 16).
Number of Templates: Select the number of templates to include in the
layout (0 to 4).
Template Size: Select the number of bytes to use in the template. The
default size is 334 bytes.
Template 1-4 Start Block: Enter the starting block for each fingerprint
template.
3. To use the custom layout, click Apply to Devices and select the appropriate
device numbers from the Device Tree dialog box.
4. To save your changes, click Save.
Note: To reset any changes you have made, click Default. To exit the dialog box
without saving changes, click Close.
3.6.4.8 Edit the iCLASS layout

BioStar allows you to customize the layout that is used to record user information
and fingerprint templates. This layout will be applied to all new iCLASS cards issued
with BioEntry Plus iCLASS devices.

BioEntry Plus iCLASS devices support 16k bit (2k Byte) and 32k bit (4k Byte) iCLASS
cards. The 16k bit (2k Byte) cards are available with either 2 or 16 application areas
and are organized into 237 blocks of 8 bytes each. The 32k bit (4k Byte) cards are
available with either 2 or 16 application areas, plus an additional 16k user
configurable memory, and are organized into 8 pages with 26 blocks of 8 bytes
each.
To edit the iCLASS layout:

1. From the menu bar, click Option > iCLASS Card > iCLASS Layout. This will
open the iCLASS Layout dialog box.
2. Enter the following parameters of the iCLASS layout:

CIS Index Block: Select the block index to use for header information
(default value is 13).
Number of Templates: Select the number of templates to include in the
layout (default is 2).
Template Size: Select the number of bytes to use in the template. The
default size is 382 bytes.
Template 1-4 Start Block: Enter the starting block for each fingerprint
template (Template 1 default value is 19; Template 2 default value is 67).
3. To use the custom layout, click Apply to Devices and select the appropriate
device numbers from the Device Tree dialog box.
4. To save your changes, click Save.
Note: To reset any changes you have made, click Default. To exit the dialog box
without saving changes, click Close.

3.6.4.9 Read card information from USB-based readers

You can specify options to read information from USB-based contactless readers
like a DE-620 by clicking Option > Card > USB Reader > Card ID Format.
Format: Set the type of pre-processing on the card ID data to Normal,

allowing the data to be processed in its original form. Wiegand type is not
supported.
Byte Order: Specify whether to swap ID card data between cards and
devices by most significant byte (MSB) or least significant byte (LSB).
Bit Order: Specify whether to swap ID card data between cards and
devices by most significant bit (MSB) or least significant bit (LSB).
3.6.5 Transfer User Data

BioStar allows you to automatically transfer user information to devices, by selecting the
Auto setting from the menu bar (Option > User > Transfer Mode > Auto). However, you
can also manually transfer data to devices. When doing so, you can either transfer selected
users to selected devices or synchronize all users at once. BioStar also allows you to retrieve
data from a device and transfer it to the BioStar server.
3.6.5.1 Transfer a user to a device

To transfer a single user or selected users to a device or devices:
2. In the task pane, click Transfer Users to Device. This will open the Select a
Device dialog box.

3. Select a device or devices from the list on the left by clicking the checkboxes
next to device names.
4. Click a user name (you can hold down the Ctrl key while selecting multiple
users).
5. If desired, click the checkbox to overwrite users with different information.
6. Click Transfer to Device to send the user information to the selected devices.
Note: You can also delete users from devices with this menu. This action cannot be
undone, so use this feature with caution. To delete users from a device, click a
users name and then click Delete Users.
When using Xpass or Xpass Slim devices as lift readers, transferring settings to the
device with the User menu will reset all of the settings and user data stored on the
device. To preserve the settings, use the Transfer to Device function in the Lift menu
instead.
3.6.5.2 Synchronize all users

To synchronize all user information between the BioStar server and connected
devices,
2. In the task pane, click Transfer Users to Device. This will open the Select a
Device dialog box (see section 3.6.5.1).
3. Select a device or devices from the list on the left by clicking the checkboxes
next to device names.
4. Click Synchronize All Users.
3.6.5.3 Retrieve user data from a device

To retrieve data from a device:
2. In the task pane, click Manage Users in Device. This will open the Select
Target Device dialog box.

3. Click a device name in the list on the left to display user templates contained
in the device.
4. Click a user in the Template Information list (new users will be highlighted in
yellow).
5. Click Get From Device.
Note: You can also delete users from devices with this menu. This action cannot be
undone, so use this feature with caution. To delete users from a device, click a
users name and then click Delete (or click Delete All to delete all user records at
once).
In the template information, Template Num is the number of fingerprint

templates stored in the device and Face Num is the number of face templates
stored in the device. Face images captured on D-Station devices are not counted in
the Template Num total.
!
Caution: If there are the same users on the BioStar database when you retrieve
user data from Xpass devices, the data will be overwritten without fingerprint
data because Xpass devices do not store fingerprint data.
3.6.5.4 Merge user data imported from the device

This is to protect the existing data in the server, but import only changed or added
user data from the device. If you choose Overwrite, this will delete the entire user
data previously saved and replace with the user data imported from the device.
To protect important user data, the following 5 items will not be merged and saved
to the server DB.
Admin Level (Changed only if admin level is Normal User in the server
database and Admin User in the device.)
Authentication mode
Number of Authentication
Authentication time limit
Password2
MERGE AND IMPORT USER DATA

1. Click Option > User > Manage Users in Device. Check the Merge option. (Default)

2. In the shortcut pane, click User.

3. In the task pane, click Manage Users in Device. This will open the Manage Users in
Device window.
4. Click the device name in the device list on the left and display user information in the
device.
5. With color information, compare user data between the device and server and select
users.
6. Click Get from Device.
3.6.6 User Data Encryption

BioStar provides AES256 user data encryption. User data encryption helps protect valuable
private information against crimes such as identity theft upon any accidental or intentional
data breach.
To encrypt user data:

1. Click Option > User > Personal Information Encryption.
2. In the Personal Information Encryption dialog box, click the check box beside Use
Personal Information Encryption a pop-up window will appear.
3. Read the message then click Yes to accept it.
4. Click Change Encryption Key then enter the encryption key.

Note You can use Personal Information Encryption without encryption keys. Any
combination of letters, numbers and special characters up to 32 characters can be used as
the encryption key.
5. Click Change to close the window then click Save to save changes.
3.7 Setup Timezones

In the BioStar system, timezones are used to schedule permissions and restrictions. You can
apply timezones to restrict the hours that a user is permitted to access a door by combining
doors and timezones in access groups (see section 3.8).
3.7.1 Create a Timezone

To create a timezone schedule:
1. Click Access Control in the shortcut pane.
2. In the task pane, click New Timezone.
3. Enter a name for the timezone.
4. In the Timezone pane, create a weekly schedule by highlighting the effective hours for
each day. You can copy a schedule from one day to the next by clicking the arrow to
the right of the day.

5. If desired, you can add up to two holiday schedules to the timezone. To create holiday
schedules, see section 3.7.2.
6. When you are finished creating the timezone, click Apply.
7. Next, transfer the timezone data to devices:
8. In the task pane, click Transfer to Device. This will open the Device Tree dialog box.
9. Select a device or devices by clicking the checkboxes in the Device Tree dialog box.
10. Click OK.
You can now combine the timezone with door permissions to create an access group (see
section 3.8).
3.7.2 Create a Holiday Schedule

To create a holiday schedule:
2. In the task pane, click New Holiday.
3. Enter a name for the holiday.
4. In the Holiday pane, set the date the holiday begins with the drop-down calendar.

5. If the holiday recurs every year, click the checkbox below the drop-down list.
6. Set the duration of the holiday (in days).
7. Click Add to add the holiday to the list.
8. Click Apply.

3.8 Setup Access Groups

Access groups allow you to define sets of access permissions that can include doors, users,
and timezones. Before adding an access group, you must setup doors (see section 3.3) and
timezones (see section 3.7). After creating access groups, you must manually transfer the
data to affected devices (see section 3.8.4).
3.8.1 Add an Access Group

To add an access group:
2. In the task pane, click New Access Group.
3. Type a name for the new access group in the box that appears in the navigation pane
and press Enter.
4. In the Access Control tab (in the Access Group pane), click Add. This will open the
Access Group dialog box.
5. Select doors to add to the group by clicking the checkboxes next to door groups or
individual doors.
6. Select a timezone to apply to the group from the drop-down list at the bottom of the
dialog box.
7. Repeat steps 5 and 6 as necessary to add multiple sets of doors and timezones to the
access group.
8. Click OK to add your selections to the group.

3.8.2 Add Users to Access Groups

After adding access group, you must add users to the group. You can add users to access
groups from the User tab, as described below or by assigning access groups to a user from
the User pane, as described in 3.8.3. You can assign a user to a maximum of four access
groups.
To add users to access groups:

2. From the User tab (in the Access Group pane), click Add.
3. In the Add New User dialog box, select users to add to the group by checking user
groups or individual users.
4. Click OK.
If you have setup user groups, users will appear under their respective groups.
3.8.3 Assign Access Groups to Users

You can also define which access groups a user will belong to (up to four total) from the
User pane.
To assign an access group to a user:

3. Click the Access Control tab in the User pane.

4. Click Add. This will open the User Access Group dialog box.
5. Click the name of an access group from the list on the left and then click >.
6. Repeat step 5 as needed to assign additional access groups.
7. When you are finished assigning access groups, click OK.
3.8.4 Transfer Access Groups to Devices

To transfer access group data to devices:
2. In the task pane, click Transfer to Device. This will open the Device Tree dialog box.
3. Select a device or devices by clicking the checkboxes in the Device Tree dialog box.
4. Click OK.
3.8.5 Check for Access Rules by Device

You can check the access rules applied for devices by viewing access groups, timezone, and
holiday schedules by device. You can also maintain the idential configuration data across the
server and devices by either transferring or deleting the data that is inconsistent between
them.

To check access groups configured in each device:

2. In the task pane, click Manage Access Group in Device. This will open the Device Tree
dialog box.
3. Select a device in the Device tree pane.
4. Select Access Group, Timezone, or Hoilday Schedule below the Device tree pane to
view how they are configured in each device. The configuration data to the
corresponding options will be displayed in the right pane. The data will be highlited in
the following colors depending on whether they are applied in the server, a device, or
both.
Yellow: Indicates that the configuration data in both the device and the server are
identical.
Red: Indicates that the configuration data in the device and the server are
different.
Green: Indicates that the configuration data are applied to the device only.
Blue: Indicates that the configuration data are applied to the server only.
5. Optional: Select the data that you want to delete from the device and click Delete
from Device in the lower-right corner of the screen.
6. Optional: Select the data that you want to transfer from the server to a device and click
Send to Device in the lower-right corner of the screen.
3.9 Setup Time and Attendance

BioStars time and attendance features allow you to define time categories, shifts, and
holiday rules. Refer to the procedures in this section as well as the steps in section 3.7.2 to
configure time and attendance options.
3.9.1 Add a Time Category

To add a time category:
1. Click Time and Attendance in the shortcut pane.
2. In the task pane, click Add Time Category. This will open a Time Category pane similar
to the one below.

3. Enter a name and description for the time category.

4. Add details for the time category:
Time Rate: Enter the rate at which time is calculated for this time category.
Rounding Unit(Min): Specify in minutes how to round a users work time (for
example, a entry of 5 will round a users work time to the nearest 5-minute
decrement).
Display Color: Set how the time category will appear in the daily schedule.
5. Click Apply to save the time category.

3.9.2 Add a Daily Schedule

BioStar versions 1.35 and higher support a maximum of 256 daily schedules.
To add a daily schedule:

2. In the task pane, click Add Daily Schedule. This will open a Daily Schedule pane similar
to the one below.
3. Enter a name and description for the daily schedule.

4. Set the start time for the daily schedule and, if desired, click the checkbox to the right
to let the BioStar to record workers first come-in and last go-out activities via the
BioStar system as their check-in and check-out activities for the day.
5. Define the daily schedule by adding one or more time slots:
b. Specify the details for the time slot:
- Start time: Set the beginning time for the time slot. If the time slot begins in
the following calendar day, click the checkbox (Next) to the right.
- End time: set the ending time for the time slot. If the time slot ends in the
following calendar day, click the checkbox (Next) to the right.
- Time Category: Select one a time category from the drop-down list. See
section 3.9.1 to define the time categories that will appear in this list.

- Minimum Duration: Set the minimum duration for the time slot (in minutes).
Workers must be checked in for at least the minimum duration, or the system
will record no time worked for the time slot.
- Grace (Start): Activate and set a grace period for checking in late at the
beginning of the time slot (in minutes). Click the checkbox to enable the grace
period and then specify the length of the grace period in the corresponding
field. Workers who check in within the grace period will be considered to have
checked in right at the start of the time slot.
- Grace (End): Activate and set a grace period for checking out early at the end
of the time slot (in minutes). Click the checkbox to enable the grace period and
then specify the length of the grace period in the corresponding field. Workers
who check out within the grace period will be considered to checked out right
at the end of the time slot.
- Rounding (In): Specify in minutes how to round a users check-in time (for
example, a entry of 5 will round a users time to the nearest 5-minute
decrement).
- Rounding (Out): Specify in minutes how to round a users check-out time (for
example, an entry of 5 will round a users time to the nearest 5-minute
decrement).
- Auto Check IN: Enable or disable this feature to automatically check-in a user
who has failed to check-in for the time slot.
- Auto Check OUT: Enable or disable this feature to automatically check-out a
user who has failed to check-out for the time slot.
- Affect Result: Allow or disallow data from this time slot to be used to
determine overall time and attendance result per one daily schedule.
c. Click Add to add the time slot to the daily schedule.
6. Click Apply to save the daily schedule.

3.9.3 Add a Shift

To add a shift:
2. In the task pane, click Add Shift. This will open a Shift pane similar to the one below.
3. Click one of the radio buttons to set the shift as a part of a daily or weekly cycle. If you
select weekly, a calendar week will constitute a cycle. If you select daily, you can
specify any number of consecutive days (e.g., 5, 10, or 20 days) to constitute a cycle.
Note: Daily cycle is available only with the Standard Edition of BioStar.
4. Select start and end dates from the drop-down calendars.

5. Activate days of the cycle by clicking the checkboxes on the left.

6. Click the ellipsis button (...) to select a daily schedule. This will open the T&A Tree
dialog box. See section 3.9.2 to define the daily schedules that will appear in this dialog
box.
7. Select a daily schedule and click OK to apply the daily schedule to the shift.
8. Repeat steps 5-7 as needed.
Note: You can copy a schedule from one day to the next by clicking the arrow to the right
of the day. In addition, you can add up to 1,024 daily schedules to the list.
9. Click Apply to save the shift.
3.9.4 Assign Users to Shifts

Assign users to shifts to enable BioStar to record time and attendance data. You can assign
individual users to shifts via the User pane or assign multiple users to a shift via the Time
and Attendance pane.
To assign individual users to shifts via the User pane:

2. In the navigation pane, click a user name.
3. In the User pane, click the T&A tab.

4. Click the radio button next to Shift Management and then click Add at the bottom of
the User pane. This will open the T&A Tree dialog box.
5. Select a shift and click OK.

6. Click Apply to save the T&A settings for the user.
To assign multiple users to a shift via the Time and Attendance pane:
2. In the navigation pane, click a shift name.
3. In the Shift pane, click the User tab and then click Add at the bottom of the pane. This
will open the Add New User dialog box.
4. Select one or more users and click OK.

5. Click Apply to save the T&A settings for the shift.

To add a T& A rule by user:

2. Click Individual Shift in the task pane. This will open the Individual Shift dialog box.
3. Click Add Leave to define a custom leave.

4. Enter the Name and Description of the leave that you want to add and click OK. A
new leave will be added to the list.
5. Click Close.
3.9.5 Choose a Device for T&A

Devices can be chosen for the T&A report. If Default is selected, all devices are used for T&A
report. But when T&A devices are selected, T&A report is created using event logs in the
selected devices. And if it is not included as a T&A device, T&A event keys applied to the
device will not be displayed from the T&A report.

Select and deselect with >, >> or <, <<, and check selected devices and unselected devices through
the panel. Manual Add can be made through direct device ID and name input when a device is no
longer able to be found from the server but used before.
3.10 Setup Alarms

BioStar can provide multiple levels of alarm notification. The system can activate system
alarms by emitting sounds from devices and connected computers. The system can also be
configured to send email notifications to specified recipients. In addition, you can configure

the system to receive inputs from external devices (such as fire warning devices) or send
outputs to external devices (such as alarm sirens).
3.10.1 Configure Alarm Settings and Sounds

BioStar allows you to customize how the system responds to events. You can configure
alarm settings by creating customized priority levels and selecting the action to take when
an event occurs. You can also add your own alarm sounds to further customize the system.

3.10.1.1 Customize alarm actions

To customize alarm actions:
1. From the menu bar, click Option > Event > Alarm Setting. This will open the
Alarm Setting dialog box.
2. Select a priority level from the drop-down list and click Add. This will open a
list of events.
3. Select the events to include in the priority level and click OK.
4. Select an action or actions by clicking the checkboxes on the right.
Program Sound: Choose a sound from the drop-down list and then
specify the duration (play count) of the sound in seconds. If you set the
Play Count to 0, the specified sound will play until someone with
administrative privileges manually stops the sound via the Realtime
Monitoring tab in the Monitoring pane. To add custom sounds to the list,
please see section 3.10.1.2.
Send Email: Click the ellipsis button () to the right to select an email
recipient. To configure email notifications, please see section 3.10.2.
Acknowledge: Activate pop-up alerts on client PCs.
Color: Specify the color of text and background on any event raised by
priority in the Alert Window.
5. Repeat steps 2-4 as desired to customize other priority levels.
6. When you are finished, click Save.
3.10.1.2 Add custom alarm sounds

To add custom alarm sounds:
1. From the menu bar, click Option > Event > Sound Setting. This will open the
Sound Setting dialog box.

2. Click Add.
3. Locate a waveform (.wav) file on your computer or network and click Open.
4. If desired, click a sound and then click Play to hear the sound.
3.10.2 Configure email notifications

BioStar sends email notifications when an alarm event occurs (not available in the free
version). As explained in 3.10.1.1, you can customize which events will trigger an automatic
email alert. BioStar supports email notification through TLS or SSL secured mail servers.
To configure an email notification:

1. From the menu bar, click Option > Event > E-mail Setting. This will open the Email
Setting dialog box.
2. Type the email address, SMTP server, port number, SMTP ID, and SMTP password in the
Sender Info section, then choose one of the options(NO SECURITY, TLS or SSL) in the
Security Type drop-down list.
3. Type the email address in the Recipient Info section.
4. Click Add to add the configuration to the list.
5. Repeat steps 2-4 as necessary to add other email configurations.

E-mail setting
Using Alarm setting, you can send an e-mail with user-customized format.
1. Click Option > Event > Alarm Setting > Send Email > The button, then the Select
Admin & Contents window will open.
2. Click the Setup button and the Email Setting window will open.
3. Fill in Sender Info and click the Add button.
4. Click the Add button.
5. Click the Contents button and you can modify the e-mail contents settings.
6. Email contents can be applied to each Priority by using >> button.

7. Click Add to open Email Format window.
8. Select among six items in Add Real Data section to be added to Message. These items
are allocated to the actual data at the designated location when email is sent out. For
example, ##DATE## is changed to the actual date and time of the event, and ##USER##
is changed to the actual user name. Message items can be deleted manually.

3.10.3 Configure Settings for External Devices

When using external devices with BioStar, you must configure settings to determine what
actions will occur in response to input signals. For more information about configuring
devices and device settings, see sections 3.2 and 5.1.
3.10.3.1 Configure outputs to external devices

You may choose to have certain devices send signals to external devices, such as
alarm sirens, when selected events occur.
To configure outputs:
3. In the Device pane, click the Output tab.
4. Click Add at the bottom of the pane. This will open the Output Setting dialog
box.

5. Configure actions that will activate (send a signal to) a specified output relay:
a. In the Alarm On Event section, select an event from the first drop-down
list.
b. Select the device number or All Device from the second drop-down list.
c. Select a signal setting from the third drop-down list.
d. Enter a priority for the event. Only an event with an equal or higher
priority (1 is the highest) can override a previous event. For example, an
alarm on (activate) event with a priority of 2 can be canceled only by an
alarm off (deactivate) event with a priority of 1 or 2.
e. Click Add.
6. Configure actions that will turn off (stop sending a signal to) an activated
output relay:
a. In the Alarm Off Event section, select an event from the first drop-down
list.
b. Select the device number or All Device from the second drop-down list.
c. Enter a priority for the event.
d. Click Add.
3.10.3.2 Configure inputs from external devices

To integrate BioStar's door control with other alarm systems, such as fire warning
systems, you can specify the actions BioStar will take when receiving an input. You
can also configure inputs to work with manual door releases (exit buttons) and
other types of external devices.
To configure inputs:


3. In the Device pane, click the Input tab.
4. Click Add at the bottom of the pane. This will open the Input Setting dialog
box.
5. Select an input port from the second drop-down list.

6. Select the normal position of the input switch (N/O-normally open or N/C-
normally closed).
7. Select a Function to be triggered (Generic Input, Emergency Open, Release All
Alarm, Restart Device, Disable Device, LED Green Input, LED Red Input, Buzzer
Input, Access Granted Input, and Access Denied Input).
Note: With BioStar 1.8v, LED Green Input, LED Red Input, Buzzer Input, Access
Granted Input, and Access Denied Input were newly added. And these input
options are available only with BioStation (FW 1.93v), BioStation T2 (FW 1.3v),
FaceStation (FW 1.3v), BioEntry Plus (FW 1.6v), BioEntry W (FW 1.2v), BioLite
Net (FW 1.4v), and Xpass (FW 1.3v).
8. Select a function for the input (Not Use, Generic Input, Emergency Open,
Release All Alarms, Restart Device, or Disable Device).
9. Select a schedule for applying the function (Always, Disable, or custom
schedules).
10. Set the minimum duration (in milliseconds) an input signal must last to trigger
the specified action.
11. Click OK.
3.11 Setup Cameras

This section describes how to add IP cameras and network video recorder (NVR) servers to
the Biostar system. Once you have properly set up the IP cameras and NVR servers, you can
monitor areas in real time and view event logs with still images or recorded videos. BioStar
supports the following IP cameras and NVR servers:

Model Name Developer
AXIS PTZ 215 AXIS
Internet Protocol (IP) Camera AXIS M3203-V AXIS
SNP-3120VH Samsung Techwin
Network Video Recorder (NVR) AXIS Camera Station AXIS

Server NET-I Ware Samsung Techwin
3.11.1 Add an NVR Server

Network video recorder (NVR) servers store video streams transferred from all connected
cameras and allow you to view the videos when you check event logs.
To add an NVR server to the BioStar system:

1. Click Camera in the shortcut pane.
2. Click Setup Camera in the Task pane.

3. In the Task pane, click Add New Camera Server. This will open a Camera (Setup Mode)
pane similar to the one below.
4. In the Basic Information section, enter a name, type, model, IP address, and port
number for the NVR server, and then enter the BioStar user name and password
required to access the NVR server.
5. Click Detect to view cameras that are currently connected to the NVR server.
6. Click Apply at the bottom right of the Camera (Setup Mode) pane. This will add the
detected cameras under the NVR server in the navigation pane, as illustrated below.

7. In the navigation pane, click a camera name. This will open the Camera (Setup Mode)
pane.
8. Click Add at the bottom right of the Device List to open the Device Tree dialog box.
9. Click a checkbox next to a device name, and then click OK.

10. Click Apply at the bottom right to apply the changes to the BioStar system.
3.11.2 Add an IP Camera

BioStar allows you to add an IP camera, assoicate it with an access control device, and
specify the events that will trigger the IP camera to send captured still images to the BioStar
system.

To add an IP camera to the BioStar system:

2. Click Setup Camera in the Task pane (if desired).
3. In the Task pane, click Add New Camera. This will open a Camera (Setup Mode) pane
similar to the one below.
4. In the Basic Information section, enter a name, type, model, IP address, and port
number for the IP camera and enter a user name and password for the BioStar to acess
the IP camera.
5. In the Details tab, click Add at the bottom right of the Device List section to open the
Device Tree dialog box.

6. Select a device to associate the IP camera with and click OK.

7. Click Add at the bottom right of the Event List section and select an event that will
trigger the IP camera to send a captured still image to the BioStar system.
8. Click Apply at the bottom right to apply the changes to the BioStar system.
3.11.3 Configure an IP Camera

BioStar can control the movement of pan-tilt-zoom (PTZ) cameras. When you use an IP
camera that supports the PTZ feature, you can aim it at a spot you want to surveil.
To control the movement of a PTZ camera:

2. Click a PTZ camera in the navigation pane.
3. In the Camera (Setup Mode) pane, click the Setup tab.
4. Use the controls in the Pan & Tilt and the Zoom sections to aim the PTZ camera at the
desired spot.

04
Manage the BioStar
System
Once you have properly set up the BioStar system, management is fairly simple. BioStar allows you to
monitor events in real-time and view event logs by date, control parts of the system remotely, manage
users, and upgrade device firmware directly from the BioStar interface. In addition, you can activate
fingerprint encryption, if necessary, to provide an additional level of security and privacy.
4.1 Monitor Events in Real Time

The BioStar system records events from all connected devices. To monitor events in real
time, please click Monitoring in the shortcut pane, then click the Realtime Monitoring tab.

4. Manage the BioStar System
This tab shows all events that have occurred since you last logged into the system. The
tab shows the current monitoring status (Monitoring Started or Monitoring Paused) and
includes buttons for starting (play) or stopping (pause) real-time monitoring. The sound
bar icon on the right shows whether an alarm sound is currently playing (green bars) or
not (grey bars). To stop an alarm sound, click the sound bars icon.
BioStar displays the following camera icons at the front of the event logs:
Icon Description
The event log includes a still image. Click the event log to view the
image.
The event log includes a video. Double-click the event log to view the
video.
When both camera icons are displayed, single-click the icon to view the still image and
double-click the icon to view the recorded video. When you double-click the video icon, a
video playback window will appear that is similar to the one below.
Coupled with the face detection features of D-Station, X-Station, BioStation T2, or
FaceStation, administrators can verify users identity by clicking Show Image (to view the
users stored face image) and Auto Image Reflect (to view the most recent face image
captured by the local device). Clicking Show Image also opens a window at the bottom
where the user image will be displayed. Click Real Size to view the full-sized (640 x 480)
stored image, instead of a thumbnail version and click Show Popup to open the image in a
new window that can be repositioned on the screen.

To see a users photos upon successful authentication events, click Option > Event > Profile
Image Setting in the menu bar, select event types, and then click the checkbox next to
Show Image Profile. The users image will appear on the realtime monitoring tab when he or
she successfully completes one of the authentication events specified in the Profile Image
Setting dialog box.
As of BioStar V1.3, administrators can monitor users locations and authentication status via
a Roll Call (muster) feature. This feature allows administrators to determine whether users
are present, missing, or have gained entry to areas for which they are not authorized.
4.1.1 Monitor Muster Zones in Real Time

BioStar allows you to monitor and track employees during an emergency and determine
whether or not all employees have reported to the muster area.
To monitor and track employees:

1. Click Monitoring in the shortcut pane.
2. Click a muster zone in the Monitoring pane.
3. In the Task pane, click Roll Call. This will open the Roll Call dialog box.

4. Click View Report to open the Roll Call Report.
To save the report data as a comma delimited file, click Save as CSV. To print the report,
click the printer icon. To export the report, click the export icon.
4.1.2 Monitor Areas with Cameras in Real Time

BioStar allows you to monitor specified areas with the connected camera in real time.
To monitor specified areas in real time:

2. Click Monitor Camera in the Task pane (if desired).
3. Click a camera in the navigation pane.
4.2 View Event Logs

BioStar allows you to view event logs for users, doors, and zones. You can access pre-defined
logs from the Event tabs in user, door, and zone panes or view access logs from the
Administrator menu. You can also use the Log List tab in the Monitoring pane to specify log
parameters.
BioStar automatically collects log information from connected devices as long as the server
is running. However, if you have devices that are not connected to the BioStar server, you
must manually upload logs before viewing them.

4.2.1 Upload Logs to BioStar

For devices that are not connected to the BioStar server, you must manually upload logs
before viewing them.
To upload logs to BioStar:

2. Click the Log List tab in the Monitoring pane.
3. In the Task pane, click Upload Log. This will open the Upload Log dialog box.
4. Select an upload option by clicking the corresponding box:

a. Upload Log: Use this option to upload logs for a specific time period. Specify the
period with the drop-down calendars.
b. Upload All Log: Use this option to upload all logs.
c. Get Recent Log: Use this option to upload logs written since the previous upload.
d. Device Type: Specify a device type that you wan to upload log data from, either a
reader or USB.
5. Select the devices from which to upload logs by clicking the checkboxes next to the
device numbers.
6. Click OK. BioStar will download log records from the selected devices and display the
activities in the log list.
7. Note: Log upload is only supported for D-Station, X-Station, BioStation T2, and
FaceStation.

4.2.2 View Logs in User, Door, and Zone Panes

To view pre-defined logs:
1. Click User or Doors in the shortcut pane.
2. In the navigation pane, click a user, door, or zone name.
3. In the User, Doors, or Zone panes, click the Event tab.
4. Set an event period (beginning and ending dates) with the drop-down calendars.
5. Click Get Log. This will generate a list of the relevant events for the period you
specified.
4.2.3 View Logs from the Monitoring Pane

To specify log filters or view logs for groups of users, doors, or zones:
2. In the Monitoring pane, click the Log List tab.
4. Set the parameters to generate a log:
To show events by alarm priority, click the Event checkbox and select an event
priority from the drop-down list. To add a new alarm priority, click the ellipsis
button (...) to open the Alarm Priority dialog box.
To show events by user, click the User checkbox and then click the ellipsis button
() to select a user or users from the User Tree or Department Tree dialog box.
You can select all users by selecting the top level of the user tree.
To show events for a particular device, click the Device ID checkbox and then click
the ellipsis button (...) to select a device from the Device Tree dialog box. To show
only network events for a device, you can also click the Only Network History
checkbox.
To show all events, leave all the checkboxes unchecked.
To show the users image at the bottom of the tab, click Show Image. For more
information about viewing user images, see section 4.1.

5. Click Get Log to display the events.
4.2.4 View Access Logs

From the Administrator menu, you can view histories of system access and record
modification by type of user.
To view access logs:

1. From the menu bar, click Administrator > Access Log. This will open the Access Log
dialog box.
2. Click a radio button to select either administrators or users.

4. Select a type of access or modification event with the Access drop-down list.

5. If desired, specify a particular admin or user by clicking the checkbox next to the Admin
ID, Admin IP, or User ID fields, and then entering the appropriate identification.
6. Click Get Log. This will generate a list of the relevant events for the period you
specified.
4.3 Monitor Door Events via a Visual Map

BioStar allows you to conveniently manage doors on a visual representation of your actual
floor plan. On the Visual Map, you can customize your floor plan, add doors, and monitor
door status and activity (for example, whether the door is open or closed, authentication
events, and door alarms). If you have more than one floor plan, you can create additional
Visual Maps for each floor. The Visual Map feature is available only in the Standard Edition.
4.3.1 Create a Visual Map

In the setup mode, you can add the floor plan of your building and place doors.
To add the floor plan and place doors on the plan:

1. In the shortcut pane, click Visual Map.
2. In the task pane, click Setup Mode. Monitor Mode will appear in the title bar of the
Visual Map window.
3. In the task pane, click Add Visual Map. This will open a new Visual Map window on the
right.
4. In the Visual Map window, type a name for the new Visual Map.

5. At the bottom of the Visual Map window, click Set Background to add a floor plan.
The BioStar supports images larger than resolution 730x470 in jpg, bmp, gif, or png
format only.
6. Choose an image and click Open.
7. Click Add Door to add doors. This will open a window with a list of doors.
8. From the door list, click the checkboxes next to doors to add and click Apply. Door
icons will appear on the floor plan.
9. Click and drag the door icon to the desired location on the floor plan. You can
individually relocate a door icon or name by double-clicking the door icon or name.
10. To remove a door from the floor plan, click the door and then click Remove Door.
11. Repeat steps 7-10 as necessary to add additional doors.
12. When you are finished adding doors, click Apply.
Note: To remove all doors from the plan and start over, click Reset.
4.3.2 Monitor Doors on a Visual Map

In the monitor mode, you can view the status and activities for each door on the visually
enhanced map.

To monitor doors:
1. In the task pane, click Monitor Visual Map. Monitor Mode will appear in the title bar
of the Visual Map window.
2. Monitor door status and activities on the visual map, as represented by the following
icons. Door activities, such as successful authentication or alarms will appear on the
door icons:
Icon Activity
Door is closed / Door alarm is clear
Door is open
Successful authentication while door is closed
Successful authentication while door is open
Failed authentication while door is closed
Failed authentication while door is open
Held or forced open door / Held or forced open door

alarm

Note: Door icons will change only when door sensors have been assigned in the door
settigns and detect the door status. In other words, door icons change only when the door
actually opens or closes and not when you click Open Door or Close door. For more
information about door settings, see section 5.2.1.
3. To open or close a door, click a door and then click Open Door or Close Door. To
change settings for a door, click a door and then click Setup Door.
4. The current relay status can be checked through Visual Map in Monitoring.
5. Show Event Tooltip for Selected Door option is added to indicate the details of the
current door status.
6. Event or door name font size can be enlarged or reduced by selecting font size in
Setup Visual Map and Monitor Visual.

4.4 Control Doors, Alarms, and Devices Remotely

BioStar allows administrators or operators to control doors, alarms, and devices remotely.
You can open or close doors via a computer connected to the BioStar system. You can also
release (cancel) alarms remotely and lock or unlock devices.
4.4.1 Open or Close Doors

In some situations, an administrator or operator may need to open or close a door remotely.
To open or close doors:

2. The Door/Zone Monitoring tab lists door names and their statuses. To change the
status (open or closed) of a door, click the door name and then click either Open Door
or Close Door.
You can also open and close doors while monitoring a Visual Map. For more information,
see section 4.3.2.
4.4.2 Release Alarms

When an event triggers an alarm, administrators or operators can release the alarm
remotely.
To release alarms:
2. The Door/Zone Monitoring tab lists doors names and alarm events. To release (cancel)
an alarm, click the door name and then click Release Alarm.
4.4.3 Lock or Unlock Devices

BioStar allows you to lock and unlock devices to prevent unauthorized access when BioStar
is not running. This action blocks communication from devices. You can either lock devices
manually from the BioStar interface or automatically when you exit the BioStar software. All
connected devices can be simultaneously locked or unlocked, but you cannot lock or unlock
devices that are connected directly to the BioStar server.
4.4.3.1 Lock or unlock connected devices

To lock all connected devices, from the menu bar, click Option > Device > Lock All
Devices.
To unlock all connected devices:

1. From the menu bar, click Option > Device > Unlock All Devices.
2. If necessary, enter a password in the Enter Locking Password dialog box and
click OK (if you have not created a locking password, simply click OK). See
section 4.4.3.2 to create a locking password.
4.4.3.2 Set automatic device locking

To set automatic device locking:
1. From the menu bar, click Option > Device > Automatic Locking. This will
open the Auto Locking dialog box.
2. Click the first checkbox to lock all devices when exiting BioStar.
3. If desired, click the second checkbox to change the lock password:
a. Enter the old password
b. Enter the new password
c. Retype the new password to confirm.

4.4.3.3 Reset a device lock

If you have forgotten the locking password for a device, Supremas technical
support team can send you an unlock code.
To request the code:

1. From the menu bar, click Option > Device > Automatic Locking. This will
open the Auto Locking dialog box.
2. Click the Initialize Password checkbox to activate the buttons at the bottom of
the screen.
3. Click Get Challenge Code. This will open the Get Challenge Code dialog box.
4. Select the appropriate device from the drop-down list and click Get.
5. Click Save as File to save the challenge code to your computer.
6. Email the challenge code to Suprema ([email protected]). Supremas
technical support personnel will return an unlocking code to you via email.
7. When you receive the code from Suprema, open the Auto Locking dialog box
and activate the buttons (see steps 1-2).

8. Click Unlock Device and Password to Default. This will open the Write
Challenge Code dialog box.
9. Click Open Code File and locate the file sent to you by Suprema.
10. When you have opened the file, click Write. This will unlock the device and
reset the locking password to the default (no password).
4.5 Manage Users

With the BioStar system, you can delete users, transfer users to other departments, and
customize user information fields. You can also export or import user data for creating
custom reports, batch editing, or other needs.
4.5.1 Delete Users

If the occasion arises, you can easily remove users from the BioStar system.
To delete a user:
2. Right-click a user's name.
3. Click Delete User.
4. Click OK to confirm the deletion.
4.5.1.1 Delete an individual user via command cards

After issuing command cards, you can delete an individual user directly from a
BioEntry Plus, BioEntry W, Xpass, or Xpass Slim device. For more information about
issuing command cards, please see section 3.2.6.1 and 3.2.8.1.

To delete users directly from a BioEntry Plus or BioEntry W device via command
cards:
1. Place a delete card (command card) on a BioEntry Plus or BioEntry W device.
2. If authorization is required, an administrator must scan his or her fingerprints
to continue.
3. Place the user's access card on the device and then have the user place his or
her finger on the scanner (as prompted by the device).
To delete users directly from an Xpass or Xpass Slim device via command cards:
1. Place a delete card (command card) on an Xpass or Xpass Slim device.
3. Place the user's access card on the device.
4. Place the delete card on the device again to confirm the action.
4.5.1.2 Delete all users via command cards

After issuing command cards, you can delete all users directly from a BioEntry Plus,
BioEntry W, Xpass, or Xpass Slim device. For more information about issuing
command cards, see section 3.2.6.1 and 3.2.8.1.
To delete all users directly from a BioEntry Plus or BioEntry W device via command
cards:
1. Place a delete all card (command card) on a BioEntry Plus or BioEntry W
device.
2. If authorization is required, an administrator must scan his or her fingerprints
to continue.
3. Place the delete all card on the device again to confirm the action.
To delete all users directly from an Xpass or Xpass Slim device via command cards:
1. Place a delete all card (command card) on an Xpass or Xpass Slim device.
3. Place the delete all card on the device again to confirm the action.

4.5.2 Transfer Users to Other Departments

BioStar makes moving users to other departments very simple. Before transferring a user,
you must create a department.
To create a department:
2. In the navigation pane, right-click User.
3. Click Add Department.
4. Enter a name for the department.
To transfer users to a department, simply click and drag a user name onto a department
name.
4.5.3 Customize User Information Fields

BioStar allows you to customize user information fields. This can be useful for altering the
default information fields or for creating new fields.
4.5.3.1 Add new information fields

To add new information fields:
1. From the menu bar, click Option > User > Custom Field Setting. This will
open the Custom Fields Management dialog box.
2. Select an order number from the first drop-down list (choose a number that is
not already in use).

3. Select a field type from the second drop-down list. To restrict the field to
numerical values, click the Only Digit checkbox.
4. Enter item data (for example, items to appear in a combo box) and a name for
the item.
5. Click Add.
6. Repeat steps 2-5 as desired to create additional information fields.
4.5.3.2 Modify existing information fields

To modify existing information fields:
1. From the menu bar, click Option > User > Custom Field Setting. This will
open the Custom Fields Management dialog box (see section 4.5.3.1).
2. Click the item you want to modify in the list at the bottom. The data will
appear in the fields at the top of the screen.
Note: Items 1-4 are required fields and cannot be modified or deleted.
3. Modify the data as desired.

4. Click Modify.
5. Repeat steps 2-4 as desired to modify additional information fields.
4.5.4 Export User Data

Exported user data is formatted as a comma-delimited file (CSV), which can be edited with a
text editor or Microsoft Excel.
To export user data:

2. In the task pane, click Export User. This will open the Exporting dialog box.

3. Select types of user data to export by clicking items in the list on the left and then
clicking >.
4. Optional: Click Show Column Name below the selected filed list to include a fields
column name with its data in an exported file.
5. After selecting all the types of user data to export, click Next.
6. Type a path and filename for the user data or click Browse to select a location to save
the file.
7. Click Next.
8. Click Export to begin exporting the user data.
9. When the export is complete, click Finish.
4.5.5 Import User Data

User data in comma-delimited format (CSV) can be imported to BioStar.
To import user data:

2. In the task pane, click Import User. This will open the Importing dialog box.
3. Type a path and filename where the user data is located or click Browse to select a file.
4. Click Next. The raw data types will be displayed and the User list field will default to
Not use. Click here to change.
5. Click the cell to the right of a data sample. This will open the Setup Field dialog box,
which allows you to map the raw data to a user information field in BioStar.

6. Map the data to a field by selecting a field label from the drop-down list and then click
OK.
Note: Up to four department levels can be displayed in BioStar. In the CSV file, include
department levels in the same cell, separated by slashes (for example, Department
1/Department 2/Department 3), and then map the cell to the Department field in BioStar.
7. Repeat steps 5-6 as necessary to map additional data.

8. Click Next after matching data value and filed name correctly.
If the CSV column type exported from BioStar has not been changed, you can drop 5-7
steps by the auto select button which enables to connect the column and field
automatically.
9. Click Import.
10. If you map data to fields in an existing user account, you will prompted to confirm that
you wish to overwrite the existing data. Click Yes or Yes to All to confirm or click No or
No to All to deny.
11. Click Finish.
4.6 Manage Time and Attendance

BioStar allows you to monitor the time and attendance status of users and generate reports
of T&A events, which you can edit or export as needed.
4.6.1 Monitor T&A Status via the IO Board

The IO Board displays time and attendance events only for entrance and exit events
performed via the T&A function keys of access control devices. This feature is available only
in the Standard Edition of BioStar.
You can use the board to verify recent T&A activities or to quickly determine which users are
checked in or out. Users can use the board to view their own T&A activities.

To monitor the time and attendance status of users:

2. From the task pane, click IO Board. This will open the IO Board dialog box.
3. Click User, a user name, or a department name in the pane on the left. This will display
the corresponding T&A status in the pane on the right.
4. To close the dialog box, click Close.
4.6.2 Generate T&A Reports

You can generate T&A reports to view various time and attendance events for users. You can
also modify and print time and attendance data for other uses, such as calculating payrolls.
To generate a T&A report:


2. In the task pane, click Report. This will open the T&A Report dialog box.
3. Click a radio button to select a report type:

Daily Report: A report of all activities for the specified date range sorted by date.
Individual Report: A report of activities for the specified date range sorted by user
ID.
Result Report: A report of activities that you specify via the drop-down list.
Edit History: A report of edited entries.
Daily Summary: A summary of activities for the specified date range sorted by
date.
Individual Summary: A summary of activities for the specified date range sorted
by user ID.
Note: In case a simple hh: mm format is desired in your Daily Report and Individual
Report rather than the original hh: mm(person) or hh: mm(day) style, click Option > TA
> Format then click Display person/day.
4. Specify the detail options in the Option area.

Display Person/Day: Determine whether Person/Day appears with data in the
report.
Time Format(1.0h): Display times in decimal dotted notation, for example, 1 Hr 7
Mins is expressed in 1.11.
In/Out Report: Display the times (up to the first 10 in and out times) when people
are authenticated to enter and exit an office or a building.
Paper Size: Select A4 or Letter size paper.

5. Select a date range by clicking the drop-down calendars.

6. Click View Report to retrieve and display the results.
Note: Click Upload Log to retrieve data from all networked devices. Click Update Report
to refresh the report with any data you have modified (see section 4.5.3).
You can sort report data by clicking any column header (the sort will toggle between
ascending and descending orders). You can also rearrange the columns by dragging and
dropping column headers in a new location. Furthermore, you can add or remove columns
by using the menu that appears when you right-click on any column header:
To add a column to the report:

1. Right-click on any column header.
2. Click Column and select a column to add to the report.
To remove a column from the report:

1. Right-click on the column you want to remove.
2. Click Remove column.
To display overtime hours in the report:

1. Click Option > T&A > Overtime Rule Setting. This will open the Overtime Rule Setting
dialog box.
2. Select a period unit which regular work hours are based on, and enter the amount of
regular work corresponding to the period. The work hours that have exceeded the
regular time would be considered overtime work and reported.
3. Click OK.
Note: To successfully display overtime hours in a report, you should set the start day
of the periold to Sunday of the week that you want to check for.

4.6.3 Modify T&A Reports

Time and attendance data can be modified for time reporting or payroll purposes. After
generating a T&A report, you can locate cells that you want to modify and then click the cell
and enter a new value or select an option from the drop-down list. This will save the
modification to the report, but it will not overwrite the original data collected from access
control devices. If you want to reproduce the report with the original data, click the
checkbox next to Rebuild and then click Update Report.
To perform detailed modifications on report data:

1. Generate a T&A report as described in 4.5.2.
2. Right-click a cell and click Detailed editing. This will open the Edit Data dialog box.
3. To edit an event, change the following event properties as necessary and then click
Edit Event. To add an event, change the following event properties as necessary and
then click Add Event. To delete the event, click Delete Event.
Date: Select whether the event occurred on this day or the next day.
Event: Select the type of event.
Time: Set the time of the event.
Device: Set the device where the event occurred.
4. When you are finished modifying the event data, click the X in the top right corner to
close the dialog box.
5. In the T&A Report window, ensure that the Rebuild checkbox is NOT checked.

6. Click Update Report. The report will show the changes you have made. The changes
you have made via the detailed editing will not be restored to the original data even if
you click the check box next to Rebuild and click Update Report. If you want to
reproduce the report with the original data, click the checkboxes next to Rebuild and
Rebuild All and then click Update Report.
Note: You can sort report data by clicking any column header (the sort will toggle between
ascending and descending orders). You can also rearrange the columns by dragging and
dropping column headers in a new location.
4.6.4 Print or Export T&A Report Data

To print or export T&A report data:
1. Generate a T&A report as described in 4.5.2 and make any necessary modifications as
described in 4.5.3.
2. Click View Report. This will open a preview window similar to the one below.
3. To print the report, click the print icon on the toolbar.

4. To export report data, click the export icon on the toolbar and then select an export
format and a destination. You can export data in the following formats:
Adobe Acrobat (PDF)
Crystal Report (RPT)
HTML 3.2 or 4.0
Microsoft Excel 97-2000 or Microsoft Excel 97-2000data only (XLS)
Microsoft Word or Microsoft Wordeditable (RTF)
Open Database Connectivity (ODBC)
Record StyleColumns with spaces (REC)

Report Definition (TXT)

Rich Text Format (RTF)
Comma Separated Values (CSV)
Tab Separated Text (TTX)
Text (TXT)
XML
Note: You can refresh the report data by clicking the refresh icon on the toolbar. You can
also search for text in the report by clicking the search (binoculars) icon on the toolbar.
4.7 Manage Devices

You can easily remove devices, if necessary, and upgrade the device firmware directly from
the BioStar interface. When removing devices, first ensure that any new data that may have
been added at the terminal has been transferred to the BioStar server.
4.7.1 Remove Devices

If you need to remove a device from the BioStar system, click Device in the shortcut pane,
then right-click the device name and click Remove Device.
4.7.2 Upgrade Device Firmware

On occasion, it is necessary to upgrade your devices to the latest firmware version.
To upgrade device firmware:

1. From the menu bar, click Option > Device > Firmware Upgrade. This will open the
Firmware Upgrade dialog box.

2. Click the radio button next to the type of device you want to upgrade.
3. Click Select Device and select a device or devices from the Device Tree dialog box.
4. Click OK to close the Device Tree dialog box.
5. Click Select Firmware.
6. Locate the firmware file on your computer or network and click Open.
7. Click Upgrade.
8. When the firmware upgrade is complete, wait for the device to restart, and then click
Close.
4.7.3 Downgrade Device Firmware

Devices may not work properly if downgraded or reverted back to an older version of
firmware. Suprema does not recommend a downgrade. If your devices require a downgrade,
please contact Suprema Technical Support (Email: [email protected]), your
Suprema distributor, or a local Suprema dealer.
4.8 Activate Fingerprint Encryption

By default, additional fingerprint encryption is turned off. In most cases, activating this
encryption is unnecessary. However, you may choose to turn on the encryption to provide
extra security or privacy. Keep in mind that activating fingerprint encryption requires
management of encryption keys and should be performed only by advanced users.
Activating fingerprint encryption will render all previously saved templates unusable. As a
result, it is best to activate the encryption prior to registering users.
To activate fingerprint encryption:

1. From the menu bar, click Option > Fingerprint. This will open the Fingerprint dialog
box.

2. Click the checkbox under Security Option to activate the fingerprint template
encryption.
3. Click Yes to acknowledge the warning statement.

4. If desired, you may also change the encryption key:
a. Click Encryption Key. This will open the Change Encryption Key dialog box.
b. Enter a new encryption key in the first field.

c. Confirm the key by entering it in the second field.
d. Click Change.
5. Click Save. The option you have chosen will appear on the Fingerprint tab in the Device
pane.
4.9 Change the Fingerprint Template

BioStar offers three types of fingerprint templates: ISO 19794-2, ANSI378, or Supremas
proprietary format. Supremas format is active by default. Changing fingerprint template
options will render all previously saved templates unusable. As a result, it is best to choose a
template option prior to registering users.
To change the fingerprint template option:

1. From the menu bar, click Option > Fingerprint. This will open the Fingerprint dialog
box.
2. Click the checkbox under Use ISO Format Template to select the ISO format or Use
ANSI378 Format Template to select the ANSI format.
3. Click Yes to acknowledge the warning statement.
4. Click Save.

05
5. Customize Settings
Customize Settings
This section describes the settings available in the BioStar software. BioStar provides precise control
and customization of the access control system via settings for device functions, door and zone
behaviors, and user accounts.
5.1 Customize Device Settings

While most device settings are similar for BioStation, BioEntry Plus, BioEntry W, BioLite Net,
Xpass, Xpass Slim, D-Station, and X-Station devices, the devices provide slightly different
capabilities. The sections that follow describe the settings for each device separately. To
access the tabs described below, click Device in the shortcut pane, then click a device name.
5.1.1 Customize Settings for BioStation Devices

The sections that follow describe the settings available for BioStation devices. Customize the
way BioStation devices function by changing these settings to suit your particular
environment and operational needs.

5.1.1.1 Operation Mode tab

The Operation Mode tab allows you to customize time and various operation
modes settings for BioStation devices.
BioStation Time
Date: Manually set the device date with a drop-down calendar.
Time: Manually set the device time.
Sync with Host PC Time: Check this box to get the time of the lcoal
PC which BioStar client program is installed on. The time will be
displayed in the Date and Time spin boxes right below this option
and you can set the devices time to match this time by clicking Set
Time.
Get Time: Get the current time displayed by the device.
Set Time: Set the time on the device.
1: 1 Operation Mode: the drop-down lists in this area allow you to control
the authentication mode by schedule. For example, you can choose a normal
authentication mode for working hours and a more strict authentication mode
for hours outside the normal schedule. You can specify authentication modes
either by device or by user (see section 5.4.1). Unless a particular mode is
specified for a user, the device authentication mode will apply.
ID/Card + Fingerprint: Set the device to require ID or card plus
fingerprint authorization (Always, Disable, or custom schedule).
ID/Card + Password: Set the device to require ID or card plus
password authorization (Always, Disable, or custom schedule).
ID/Card + Fingerprint/Password: Set the device to require ID or card
plus fingerprint or password authorization (Always, Disable, or custom
schedule).

Card Only: Set the device to require only card authorization (Always,
Disable, or custom schedule).
ID/Card + Fingerprint + Password: Set the device to require ID or
card plus fingerprint plus password authorization (Always, Disable, or
custom schedule).
Mifare (available only on BioStation Mifare devices)
Not use Mifare: Check this box to disable MIFARE card authorization.
Use Template on Card: Check this box to use the template on the
MIFARE card for authorization.
View Mifare Layout: Click this button to view the MIFARE layout used
by the device. For more information about configuring MIFARE
layouts, please see section 3.6.4.7.
Card ID Format
Format Type: Set the type of pre-processing to occur on card ID data
(Normal or Wiegand). If Normal is selected, the card ID data will be
processed in its original form. If Wiegand is selected, devices will
interpret card ID data according to the Wiegand format settings.
Other options
1: N Schedule: Set a schedule for using fingerprint only
authentication (Always, Disable, or custom schedule).
1: N Operation Mode: Set a method for activating the fingerprint
sensor (Auto, Ok/Function Key, or None).
Private Auth: Set the device to allow a private authorization method
(Disable or Enable). If enabled, the authentication mode of the user will
be determined by a users Authorization setting, which is located on
the Details tab. If disabled, the authentication mode will be
determined by operation mode settings of the device.
Double Mode: Set the device to require authentication of two users
access cards or fingerprints (Always, Disable, or custom schedule). The
timeout for presenting the second authentication is 15 seconds.
Fast ID Matching: Set the device to allow quicker authentication, by
requiring users to input only the first two digits of the user ID and
scan a single fingerprint (Enable or Disable). This option attempts
authentication for a smaller subset of users (only those with the same
first two digits in their user IDs) to increase matching speed.
Note: This option does not support server matching (see 5.1.1.2). When
using function keys for T&A events (see 5.1.1.8), only keys F1-F4 are
supported (BioStation V1.7 and higher).

Interphone: Set the device to act as an interphone to allow

communication between people on either side of the door (Not Use or
Use).
In Double mode, setting option which includes an admin user is supported.
In Double mode, door relay will not open unless an admin user authenticates
within 15 seconds after a normal user authenticates. If this option is not
activated, the door relay will open when other two users, regardless of
whether being a normal user or an admin user.
Note:This feature is supported from the FW versions, BioStation 1.93,
BioStation T2 1.3, FaceStation 1.3,
BioEntry Plus 1.6, BioEntry W 1.2, BioLite Net 1.4, Xpass 1.3.
- Use Wiegand Card Bypass: By Wiegand setting in BioStar, this feature exports
CSN regardless of whether the authentication is successful or not. This is
designed to be used as a dummy reader that doesnt have a door control
feature. When a card data input is made, the device sends out the data through
Wiegand without going through a matching process.
Note:This feature is supported from the FW versions, BioStation 1.93, BioStation
T2 1.3, FaceStation 1.3,
BioEntry Plus 1.6, BioEntry W 1.2, BioLite Net 1.4, Xpass 1.3.

5.1.1.2 Fingerprint tab

The Fingerprint tab allows you to customize fingerprint authorization settings for
BioStation devices.
Fingerprint
Security Level: Set the security level to use for fingerprint
authorization (Normal, Secure, or Most Secure). Keep in mind that as
the security level is increased, so too is the likelihood of a false
rejection.
Image Quality: Set the strictness of the quality check for fingerprint
scans (Weak, Normal, or Strict). If a fingerprint image is below the
specified quality level, it will be rejected.

Sensitivity: Set the sensitivity of the fingerprint scanner (0 [Min] to 7

[Max]). A higher sensitivity setting will result in more easily captured
fingerprint scans, but also increases the sensitivity to external noise.
1: N Delay: Set the delay between scans when identifying fingerprints
(0 sec to 10 sec). This delay prevents the scanner from processing the
same fingerprint more than once if a user has not yet removed his or
her finger from the scanner.
1: N Fast Mode: Set the device to use Fast Mode to reduce the
amount of time required for matching fingerprints (Auto, Normal, Fast,
or Fastest). Setting Fast Mode to Auto will adjust the matching speed
according to the number of enrolled templates.
View Image: Set to show or hide fingerprint images on the BioStation
display (Yes or No).
Scan Timeout: Set the length of time before the fingerprint scanner
will timeout (1 sec to 20 sec). If a user does not place a finger on the
device within the timeout period, the authorization will fail.
Matching Timeout: Set the length of time before the device will
timeout when trying to identify a fingerprint match (0 [Infinite] to 10
sec).
Server Matching: Enable this setting to perform fingerprint or card ID
matching at the BioStar server, instead of the device. When this mode
is enabled, the devices will send the fingerprint template or card ID to
the server to verify a match. This mode is useful when you have more
users than can be downloaded to a device or user information cannot
be distributed due to security concerns.
Check Fake Finger: Set the device to detect the use of fake
fingerprints, such as those made from silicon or rubber, and prevent
unauthorized access.
Check Duplicate FP: Set the device to determine whether or not a scanned
fingerprint has been previously enrolled. If the device determines that a
fingerprint has been previously enrolled, the enrollment process will fail.
5.1.1.3 Network tab

The Network tab allows you to customize network and server settings for
BioStation devices.

TCP/IP Setting
LAN Type: Select a type of LAN connection from the drop-down list
(Disable, Ethernet, or Wireless LAN).
Port: Specify a port to use for the device.
WLAN: Select a preset WLAN configuration from the drop-down list.
This option is active only when WLAN is selected as the TCP/IP setting.
Change setting: Click to specify settings for a wireless local area
network (WLAN). This option is active only when WLAN is selected as
the TCP/IP setting. For more information about configuring settings
for a WLAN, please see section 3.2.4.
Use DHCP: Click this radio button to enable the dynamic host
configuration protocol (DHCP) for the device.
Not Use DHCP: Click this radio button to disable the dynamic host
configuration protocol (DHCP) for this device.
IP Address: Specify an IP address for the device.
Subnet: Specify a subnet address for the device.
Gateway: Specify a network gateway.
Max Conn.: Specify the maximum number of connections to allow.
Server
Use: Click this radio button to enable the server mode.
Not use: Click this radio button to disable server settings.
IP Address: Specify an IP address for the BioStar server.
Server Port: Specify the port used to connect to the server.
SSL: Displays the status of SSL for the server connection.
Time sync with Server: Check this box to synchronize the device time
with the server. The device polls for a time change on the server every
one hour and its time will be synchronized with the server when the
devices time and the servers time differ by more than 5 seconds.
RS485

Mode: Set the mode for a device connected via RS485 (Disable, Host,
Slave, or PC Connection). For more information about RS485 modes,
see sections 3.2.1 and 3.2.2.
Baudrate: Set the baud rate for a device connected via RS485 (9600 to
115200).
RS232: Set the baud rate for a device connected via RS232 (9600 to 115200).
USB Setting: Click the radio buttons to enable or disable the USB port on
the BioStation device.
5.1.1.4 Access Control tab

The Access Control tab allows you to customize entrance limit settings and default
access groups for a BioStation device.
Entrance Limit Setting

Timed APB (min): Set the duration (in minutes) that a user will be
unable to regain entry to an area via the device. Once a user has
gained entry, the device will reject the users card or fingerprint
authorization for the time period specified here.
Option 1-4: Click the checkbox to enable an entrance limit setting,
and then specify the effective hours for the entrance limit.
Max Number of Entrance: Set the maximum number of entries
allowed during the specified time limit.
Default Group Setting: Select a default access group to be applied to new
users who have not been assigned to another access group.
5.1.1.5 Input tab

The input tab lists input settings you have specified for a BioStation device. Buttons
at the bottom of the tab allow you to add, modify, or delete input settings. To add
or modify settings, you must specify them from the Input Setting dialog box. For
more information about configuring input settings, see section 3.10.3.2.

Device: Select the BioStation (or Secure I/O) device for which you will add or
modify settings.
Port: Select an input port (Input 0, Input 1, or Tamper). For Secure I/O
devices, these settings are available: Input 0, Input 1, Input 2, Input 3.
Switch: Click the radio buttons to specify the normal position of the input
switch (N/O: normally open or N/C: normally closed).
Function: Select an action to associate with the input:
Not Use: The input port will not be monitored.
Generic Input: The input port will be monitored for a triggering
action (For the events specified with Detect Input 0-3 in the Output
Setting dialog box, please see section 5.1.1.6).
Emergency Open: Open doors controlled by this device. The normal
door open period will be ignored and doors will remain open until an
operator sends a Close Door command via the Door/Zone
Monitoring tab (see section 4.4.1).
Release All Alarms: Cancel alarms associated with this device.
Restart Device: Restart the device.
Disable Device: Disable the device. A disabled device will not
communicate with the BioStar server or process fingerprints or card
inputs. To enable communication again, an administrator must enter
the master password for a BioStation device or provide authentication
locally for a BioEntry Plus or BioEntry W device.
With BioStar 1.8v, LED Green Input, LED Red Input, Buzzer Input, Access
Granted Input, and Access Denied Input were newly added. And these input
options are available only with BioStation (FW 1.93v), BioStation T2 (FW 1.3v),
FaceStation (FW 1.3v), BioEntry Plus (FW 1.6v), BioEntry W (FW 1.2v), BioLite
Net (FW 1.4v), and Xpass (FW 1.3v).
Schedule: Set the schedule during which the inputs will be monitored
(Always, Disable, or custom schedule).
Duration (ms): Set the duration (in milliseconds) an input signal must last to
trigger the specified action.

5.1.1.6 Output tab

The Output tab lists output settings you have specified for a BioStation device.
Buttons at the bottom of the tab allow you to add, modify, or delete output
settings. To add or modify settings, you must specify them from the Output
Setting dialog box. For more information about configuring output settings, please
see section 3.10.3.1.
Device Type: Select the device type for which you will add or modify
settings.
Port: Select an output port (Relay 0). For Secure I/O devices, these settings
are available: Relay 0 or Relay 1.
Alarm On Event: Specify settings and click Add to add the event to the
Alarm On Event list. These events will activate an alarm.
Event: Select an event that will activate an alarm (Auth Success, Auth
Fail, Auth Duress, Anti-passback Fail, Access Not Granted, Entrance
Limited, Admin Auth Success, Tamper On, Door Opened, Door Close,
Forced Open Door, Held Open Door, Detect Input #1-3).
Device: Select the device to monitor for an alarm event.
Signal Setting: Select a signal setting that you have previously
configured from the menu bar (Option > Event > Output Port
Setting).
Priority: set a priority for the event. Only an event with an equal or
higher priority (1 is the highest) can override a previous event. For
example, an alarm on (activate) event with a priority of 2 can be
canceled only by an alarm off (deactivate) event with a priority of 1 or
2.
Alarm Off Event: Specify settings and click Add to add the event to the
Alarm Off Event list. These events will deactivate an alarm.

Event: Select an event that will deactivate an alarm (Auth Success, Auth
Forced Open Door, Held Open Door, or Detect Input #1-3).
Priority: Set a priority for the event. Only an event with an equal or
example, a priority 2 alarm on event (activate) can be overridden
only by an alarm off (deactivate) event with a priority of 1 or 2.
5.1.1.7 Black List tab

The Black List tab allows you to register user IDs or access card numbers and
prevent them from being authenticated with the device.
Current Count: The total number of user IDs and access cards that have
been registered.
Reserved: The remaining number of user IDs and access cards that can be
registered.

5.1.1.8 Display/Sound tab

The Display/Sound tab allows you to customize the BioStation display and event
sounds. To save changes to display or sound settings, you must click Apply at the
bottom of the tab. You can also apply the same settings to other devices by clicking
Apply to Others.
Display/Sound
Language: Set the language to use on the display (Korean, English, or
Custom).
Sub Info: Set the info to display at the bottom of the BioStation
display (Time, or None).
Menu Timeout: Set the length of time before the display will return to
the idle screen (Infinite, 10 sec, 20 sec, or 30 sec).
Private Msg: Enable or disable the option to show a private message
on the BioStation display (Disable or Enable). You can add a private
message from the Event tab in the User pane: click Modify Private
Information, set options for display count and display duration, enter
text in the Private Message field, and then click Save.
Resource: Set the language resource file to use for the BioStar
interface (No Change, English, Korean, or Custom). To use a language
resource file other than English or Korean, select Custom and then
click the ellipsis () button to locate the resource file.
Background: Set the type of background for the BioStation display
(Logo, Notice, or Slide Show). Supported file types (JPG, GIF, BMP, and
PNG) cannot exceed 320x240 pixels each. Only one image at a time
can be used as a logo or notice, while up to 16 images can be
displayed (at a set interval) in a slide show.
Notice: Click this button to create a notice that will be shown on the
BioStation display. After creating a notice, you can click Apply to apply

the notice to the current device or Apply to Others to apply the

notice to additional devices.
Volume: Set the volume of the BioStation device (10% to 100%).
Msg Timeout: Set the length of time that a failure or confirmation
message will be displayed.
Background Image: Click this checkbox to upload new background images.
Click the plus sign (+) to locate and add a new image file.
Sound: Click this checkbox to enable and add custom event sounds. Click an
event from the list and then click the plus sign (+) to locate and add a new
sound file.
5.1.1.9 T&A tab

The T&A tab allows you to configure the mode and key settings for a BioStation
device. To save changes to time and attendance settings, you must click Apply at
the bottom of the tab. You can also apply the same settings to other devices by
clicking Apply to Others.
T&A Mode: Set the time and attendance mode:

Not Use: Disable the time and attendance functions for this device.
Manual: Users must press the specified key every time they enter or
leave to record their T&A events.
Manual Fix: When a T&A key is pressed, the device will remain in that
mode until a different T&A key is pressed.
Auto change: The device will automatically change T&A modes to
correspond with the functions specified for a time period.
Event Fix: The device will perform only the specified T&A function.
T&A Key: Specify which keys to use for T&A events and the event types
associated with them:

Function Key: Select a function key from the drop-down list to assign
a T&A event (F1-F4, 1-9, CALL, 0, or ESC). If you are using the Event Fix
mode, you can click the checkbox to the right to designate a fixed
event.
Event Caption: Enter a caption for the event.
Auto Mode Schedule: When using the Auto Change mode, you can
specify when the event will occur by selecting a timezone in the drop-
down list. For more information on creating a timezone, please see
section 3.7.1.
Event Type: Set the type of event to assign to the key (Not Use, Check
In, Check Out, In, or Out). In/Out indicates the general check in/out
events during a day whereas Check In/Out indicates the formal check
in/out events upon arrival and departure at workor the first checkin
and the last checkout events on that day. When you choose Check In
or Check Out, you can enable the Regard as normal check-in/check-
out event option. If this option is enabled, users who activate the
appropriate keys will be regarded as arriving or leaving on time at
work even though they actually arrive late or leave early. If you enable
the Only Result option, they appear being on time on T&A reports
but their work time will be calculated correctly based on their actual
check in/out time. If you choose Out, you can enable the Add work
time after this event option. If this option is enabled, users activating
the appropriate key will be considered working for the remainder of
the time slot even if they leave the office early.
5.1.1.10 Wiegand tab

The Wiegand tab allows you to configure the Wiegand format for a BioStation
device. Click Change Format to launch the Wiegand Configuration wizard. For
more information on configuring the Wiegand format, see section 3.2.13.
Wiegand Mode: Set the mode of Wiegand input to use when reading card
ID data (Legacy or Extended). The Legacy mode will treat connected RF

devices as part of their host devices (this is the typical function of previous
versions of BioStar). The Extended mode will allow RF card readers to
operate independently, which allows them to be associated with doors,
included in zones, and leave logs with their own device IDs.
Wiegand Input: Assign the Wiegand input:
Disabled: The input will not be used.
Wiegand [Card]: The ID field of the Wiegand string is interpreted as a
card ID.
Wiegand [User]: The ID field of the Wiegand string is interpreted as a
user ID.
Wiegand Output: Assign the Wiegand output:
Disabled: The output will not be used.
Wiegand [Card]: Inserts the card ID of the authenticated user in the
ID field of the Wiegand string.
Wiegand [User]: Inserts the user ID of the authenticated user in the
5.1.2 Customize Settings for BioEntry Plus or BioEntry W

Devices
The sections below describe the settings available for BioEntry Plus and BioEntry W devices.
Customize the way BioEntry Plus or BioEntry W devices function by changing these settings
to suit your particular environment and operational needs.

modes settings for BioEntry Plus or BioEntry W devices.
BioEntry Plus Time/BioEntry W Time


In Double mode, setting option which includes an admin user is supported. In

Double mode, door relay will not open unless an admin user authenticates
within 15 seconds after a normal user authenticates. If this option is not
activated, the door relay will open when other two users, regardless of
whether being a normal user or an admin user.
Note: This feature is supported from the FW versions, BioStation 1.93, BioStation
T2 1.3, FaceStation 1.3, BioEntry Plus 1.6, BioEntry W 1.2, BioLite Net 1.4,
Xpass 1.3.
- Use Wiegand Card Bypass: This feature makes the device to send out Card CSN
according to Wiegand setting of BioStar without having to conduct a matching.
This is designed to be used as a dummy reader in a connection with a third
party access control unit through Wiegand. When a card data input is made,
the device sends out the data through Wiegand without going through a
matching process.
Note: This feature is supported from the FW versions, BioStation 1.93,
BioStation T2 1.3, FaceStation 1.3, BioEntry Plus 1.6, BioEntry W 1.2, BioLite
Net 1.4, Xpass 1.3..)
Time.
Operation Mode: For each of the following options, click the corresponding
checkbox to enable Double Verification Mode, which requires verification of
two users credentials to gain entry to a door.
All: Set the device to allow all types of authorization (Always, Disable,
or custom schedule).
Card + Fingerprint: Set the device to require card plus fingerprint
authorization (Always, Disable, or custom schedule).
Only Fingerprint: Set the device to require only fingerprint
authorization (Always, Disable, or custom schedule).
Only CARD: Set the device to require only card authorization (Always,
be determined by a users authorization setting (Private Auth Mode),
which is located on the Details tab in the User pane. If disabled, the
authentication mode will be determined by the operation mode
settings of the device.
Double Verification Mode: Set the device to require verification from
two users during a selected schedule (Always, Disable, or custom
schedule).

Mifare/iCLASS (available on select models)

Bio Entry Plus Mifare devices:
Not use Card: Check this box to disable MIFARE card authorization.
Card Reading Mode: Set the tyupe of card authorization mode
(Mifare Template or Mifare CSN only)
View Mifare Layout: Click this button to configure the MIFARE layout
used by the device. For more information about configuring MIFARE
Bio Entry Plus iCLASS devices:
Not use Card: Check this box to disable iCLASS or FeliCa card
authorization.
Card Reading Mode: Set the type of card authorization mode (iCLASS
Template, iCLASS CSN only, or FeliCa CSN only).
View Card Layout: Click this button to configure the iCLASS layout
used by the device. For more information about configuring iCLASS

Card ID Format

BioEntry Plus or BioEntry W devices.
Fingerprint
rejection.
sec).

5.1.2.3 Network tab

The Network tab allows you to customize network and server settings for BioEntry
Plus or BioEntry W devices.
TCP/IP
Server
Use: Click this radio button to use specific server settings.
Support 100 Base-T: This option allows you to enable or disable a fast
Ethernet connection for the device. When enabled, the device will detect
the Ethernet network and automatically establish the best connection. If
you do not enable this option, the device will attempt to establish a
10Base-T Ethernet connection.

Use: Click this radio button to enable the 100base-T connection for
the device.
Not Use: Click this radio button to disable the 100base-T connection
for the device.
RS485
Slave, or PC Connection).
115200).
Support MTU Size setting
Devices affiliated with Black Fin support MTU Size setting. The supported
packet size is between 1078 and 1514, and the default is 1514.
Note: This feature is supported from the FW versions, BioEntry Plus 1.6,
BioEntry W 1.2, BioLite Net 1.4, Xpass 1.3.

access groups, and T&A mode settings for a BioEntry Plus or BioEntry W device.

Default Access Group Setting: Select a default access group to be applied
to new users who have not been assigned to another access group.
Automatic T&A Mode Change

T&A Mode: Set the time and attendance mode for the device
(Disable, Fixed In, Fixed Out, and Auto).
Fixed Entrance: When the Auto T&A mode is selected, specify when
to allow entrance events by selecting a timezone (Always, Disable, or
custom timezone) in the drop-down list. For more information on
creating a timezone, pleas see section 3.7.1.
Fixed Exit Time: When the Auto T&A mode is selected, specify when
to allow exit events by selecting a timezone (Always, Disable, or
creating a timezone, please see section 3.7.1.
In Event Caption: Set a caption for check-in.
Out Event Caption: Set a caption for check-out.
5.1.2.5 Input tab

The input tab lists input settings you have specified for a BioEntry Plus or BioEntry
W device. Buttons at the bottom of the tab allow you to add, modify, or delete
input settings. To add or modify settings, you must specify them from the Input
Setting dialog box. For more information about configuring input settings, see
section 3.10.3.2.
Device: Select the BioEntry Plus or BioEntry W (or Secure I/O) device for
which you will add or modify settings.
Generic Input: The input port will be monitored for a triggering
action (events specified with Detect Input 1-3 in the Output setting
dialog box see section 5.1.2.6).


Granted Input, and Access Denied Input were newly added. And these
input options are available only with BioStation (FW 1.93v), BioStation T2
(FW 1.3v), FaceStation (FW 1.3v), BioEntry Plus (FW 1.6v), BioEntry W (FW
1.2v), BioLite Net (FW 1.4v), and Xpass (FW 1.3v).
Schedule: Set the schedule for the input actions (Always, Disable, or custom
schedule).
5.1.2.6 Output tab

The Output tab lists output settings you have specified for a BioEntry Plus or
BioEntry W device. Buttons at the bottom of the tab allow you to add, modify, or
delete output settings. To add or modify settings, you must specify them from the
Output Setting dialog box. For more information about configuring output
settings, see section 3.10.3.1.
settings.

Setting).
2.
example, an alarm on event (activate) can be overridden only by an

been registered.
registered.

5.1.2.8 Command Card tab

The Command Card tab allows you to issue command cards. For more information
about command cards, see section 3.2.6.1.
Card ID: Enter the card ID or click Read Card and place a command card on
the reader to automatically populate the fields.
Command Type: Select a type of command card to issue (Enroll Card, Delete
Card, or Delete All Card).

The Display/Sound tab allows you to customize the LED and buzzer behaviors by
event. To save changes to these settings, you must click Update in the
corresponding section for each event.
Event: Specify the affected event by selecting it from the drop-down list.
LED: Set the LED behavior for a specified event.
Count: Enter a number of LED cycles for the specified event. Enter 0
to enable an infinite loop or -1 to disable the LED.

Colors: Specify up to three display colors from the drop-down list. The
LED will cycle through these colors in order, from top to bottom. Next
to each color, enter the duration (in milliseconds) that the LED should
display the selected color and the duration (in milliseconds) that the
LED should remain off before advancing to the next color in the cycle.
Buzzer: Set the buzzer behavior for a specified event.
Count: Enter a number of buzzer cycles for the specified event. Enter
0 to enable an infinite loop or -1 to disable the buzzer.
Volume: Set up to three tone volumes from the drop-down list (Low,
Middle, or High). The buzzer will cycle through these volumes in order,
from top to bottom. Next to each volume, enter the duration (in
milliseconds) that the buzzer should maintain the selected volume and
the duration (in milliseconds) that the buzzer should remain off before
advancing to the next volume in the cycle.
Fade Out: Set the tone volume to fade out before advancing to the
next volume in the cycle by clicking this checkbox.

The Wiegand tab allows you to configure the Wiegand format for a BioEntry Plus or
BioEntry W device. Click Change Format to launch the Wiegand Configuration
wizard. To activate the Wiegand feature for a BioEntry Plus or BioEntry W device,
click the checkbox at the top right of the tab. For more information on configuring
the Wiegand format, see section 3.2.13.

card ID.
user ID.
5.1.3 Customize Settings for BioLite Net Devices

The sections that follow describe the settings available for BioLite Net devices. Customize
the way BioLite Net devices function by changing these settings to suit your particular

modes settings for BioLite Net devices.
BioLiteNet Time


Time.
Sensor Mode
Always On: Set the device sensor to be always available on standby
(Always or Disable).
ID Entered: Set the device sensor to be available on standby only
after a valid ID is entered (Always or Disable).
OK Pressed: Set the device sensor to be available on standby only
after the OK key is pressed (Always or Disable).
Fingerprint Only: Set the device to require fingerprint only
authorization (Always, Disable, or Custom Schedule).
Password Only: Set the device to require password only authorization
(Always, Disable, or Custom Schedule).
Fingerprint/Password: Set the device to require fingerprint or
password authorization (Always, Disable, or Custom Schedule).
Fingerprint+Password: Set the device to require fingerprint plus
password authorization (Always, Disable, or Custom Schedule).
Disable, or Custom Schedule).
Mifare
View Mifare Layout: Click this button to configure the MIFARE layout
used by the device. For more information about configuring MIFARE
Card ID Format


In Double mode, setting option which includes an admin user is
supported. In Double mode, door relay will not open unless an admin
user authenticates within 15 seconds after a normal user
authenticates. If this option is not activated, the door relay will open
when other two users, regardless of whether being a normal user or an
admin user.
Net 1.4, Xpass 1.3..
Use Wiegand Card Bypass: This feature makes the device to send out Card
CSN according to Wiegand setting of BioStar without having to conduct a
matching. This is designed to be used as a dummy reader in a connection
with a third party access control unit through Wiegand. When a card data
input is made, the device sends out the data through Wiegand without
going through a matching process.
Net 1.4, Xpass 1.3.

BioLite Net devices.
Fingerprint
rejection.

sec).

5.1.3.3 Network tab

The Network tab allows you to customize network and server settings for BioLite
Net devices.

(This feature is supported from the FW versions, BioEntry Plus 1.6, BioEntry W
1.2, BioLite Net 1.4, Xpass 1.3.)
TCP/IP
Server
Time sync with Server: Check this box to synchronize the device
time with the server. The device polls for a time change on the server
every one hour and its time will be synchronized with the server when
the devices time and the servers time differ by more than 5 seconds.

the device.
for the device.

RS485
115200).

access groups for a BioLite Net device.


5.1.3.5 Input tab

The input tab lists input settings you have specified for a BioLite Net device.
Buttons at the bottom of the tab allow you to add, modify, or delete input settings.
To add or modify settings, you must specify them from the Input Setting dialog
box. For more information about configuring input settings, see section 3.10.3.2.
Device: Select the BioLite Net (or Secure I/O) device for which you will add
or modify settings.
Generic Input: The input port will be monitored for a triggering action
(For the events specified with Detect Input 1-3 in the Output setting
dialog box, please see section 5.1.3.6).
locally for a BioLite Net device.
With BioStar 1.8v, LED Green Input, LED Red Input, Buzzer Input,
Access Granted Input, and Access Denied Input were newly added.
And these input options are available only with BioStation (FW 1.93v),

BioStation T2 (FW 1.3v), FaceStation (FW 1.3v), BioEntry Plus (FW 1.6v),
BioEntry W (FW 1.2v), BioLite Net (FW 1.4v), and Xpass (FW 1.3v).
schedule).
5.1.3.6 Output tab

The Output tab lists output settings you have specified for a BioLite Net device.
Setting dialog box. For more information about configuring output settings, see
section 3.10.3.1.
settings.


Setting).
2.

been registered.
Reserved : The remaining number of user IDs and access cards that can be
registered.


The Display/Sound tab allows you to customize LED and buzzer behaviors by event.
To save changes to these settings, you must click Update in the corresponding
section for each event. You can also customize the language used on the device
display.
Custom).

Resource File: Set the language resource file to use for the BioStar interface
by clicking the ellipsis () button and locating the resource file.
5.1.3.9 T&A tab

The T&A tab allows you to configure the mode and key settings for a BioLite Net

a T&A event (*1-*15). If you are using the Event Fix mode, you can
click the checkbox to the right to designate a fixed event.
- Auto Mode Schedule: When using the Auto Change mode, you can
section 3.7.1.

out event option. If this option is enabled, users using the
appropriate keys will be regarded arriving or leaving on time at work
even though they actually come late or leave early. If you enable the
Only Result option, they appear being on time on T&A reports but
their work time will be calculated correctly based on their actual check
in/out time. If you choose Out, you can enable the Add work time
after this event option. If this option is enabled, users using the
appropriate key will be considered working for the remainder of the
time slot even though they leave the office early.

The Wiegand tab allows you to configure the Wiegand format for a BioLite Net
device. Unlike BioStation devices, only one Wiegand format can be configured at a
time (either input only or output only). You can click Change Format to launch the
Wiegand Configuration wizard. To activate the Wiegand feature for a BioLite Net
device, you can select the checkbox at the top right of the tab. For more
information on configuring the Wiegand format, pleaes see section 3.2.13.
ID data (Legacy or Extended). The Legacy mode will process ID data from
networked devices and RF card readers in the same way (this is the typical
function of previous versions of BioStar). The Extended mode will allow RF
card readers to operate independently, which allows them to be associated
with doors, included in zones, and leave logs with their own device IDs.


card ID.
user ID.
5.1.4 Customize Settings for Xpass Devices

The sections below describe the settings available for Xpass devices. Customize the way
Xpass devices function by changing these settings to suit your particular environment and
operational needs.

modes settings for Xpass devices.
Xpass Time
Time.


Server Matching: Enable this setting to perform card ID matching at
the BioStar server, instead of the device. When this mode is enabled,
the device will send card ID to the server to verify a match. This mode
is useful when you have more users than can be downloaded to a
device or user information cannot be distributed due to security
concerns.
Mifare
Use Data Card: Check this box to use the user data on the MIFARE
card for authorization. The user data card does not provide fingerprint
templates.
Card ID Format
In Double mode, setting option which includes an administrator is supported.
In Double mode, door relay will not open unless an administrator
authenticates within 15 seconds after a user authenticates. If this option is
not activated, the door relay will open when other two users, regardless of
whether being a user or an administrator, authenticate within 15 seconds.
Use Wiegand Card Bypass: This feature makes the device to send out Card
CSN according to Wiegand setting of BioStar without having to conduct a
matching. This is designed to be used as a dummy reader in a connection
with a third party access control unit through Wiegand. When a card data
input is made, the device sends out the data through Wiegand without
going through a matching process.



5.1.4.2 Network tab

The Network tab allows you to customize network and server settings for Xpass
devices.
TCP/IP
Note: This feature is supported from the FW versions, BioEntry Plus 1.6,
BioEntry W 1.2, BioLite Net 1.4, Xpass 1.3.
Server

the device.
for the device.
RS485
115200).

The Access Control tab allows you to customize entrance limit settings, default
access groups, and T&A mode settings for Xpass devices.



In Event Caption: Set a caption for check-in.
5.1.4.4 Input tab

The input tab lists input settings you have specified for an Xpass device. Buttons at
the bottom of the tab allow you to add, modify, or delete input settings. To add or
modify settings, you must specify them from the Input Setting dialog box. For
Device: Select the Xpass (or Secure I/O) device for which you will add or
modify settings.
(For the events specified with Detect Input 1-3 in the Output setting
dialog box, please see section 5.1.4.5).


Granted Input, and Access Denied Input were newly added. And these
input options are available only with BioStation (FW 1.93v), BioStation T2
(FW 1.3v), FaceStation (FW 1.3v), BioEntry Plus (FW 1.6v), BioEntry W (FW
1.2v), BioLite Net (FW 1.4v), and Xpass (FW 1.3v).
schedule).
5.1.4.5 Output tab

The Output tab lists output settings you have specified for an Xpass device. Buttons
at the bottom of the tab allow you to add, modify, or delete output settings. To add
or modify settings, you must specify them from the Output Setting dialog box. For
more information about configuring output settings, see section 3.10.3.1.
settings.

Port: select an output port (Relay 0). For Secure I/O devices, these settings
Setting).
2.
5.1.4.6 Blacklist
From BioStar 1.8, Blacklist feature is supported with Xpass.
(This feature is available only with FW 1.3v or higher.)

about command cards, please see section 3.2.8.1.


section for each event.


5.1.4.9 Wiegand tab

The Wiegand tab allows you to configure the Wiegand format for an Xpass device.
Click Change Format to launch the Wiegand Configuration wizard. To activate the
Wiegand feature for an Xpass device, click the checkbox at the top right of the tab.
For more information on configuring the Wiegand format, see section 3.2.13
card ID.
user ID.
5.1.5 Customize Settings for Xpass Slim Devices

The sections below describe the settings available for Xpass Slim devices. Customize the way
Xpass Slim devices function by changing these settings to suit your particular environment
and operational needs.


modes settings for Xpass Slim devices.
Xpass Slim Time

Time.
Server Matching: Enable this setting to perform card ID matching at
the BioStar server, instead of the device. When this mode is enabled,
the device will send card ID to the server to verify a match. This mode
is useful when you have more users than can be downloaded to a
device or user information cannot be distributed due to security
concerns.
Mifare: Mifare template cards are not supported in the Xpass slim device.
Card ID Format

5.1.5.2 Network tab

The Network tab allows you to customize network and server settings for Xpass
Slim devices.
TCP/IP
IP: Specify an IP address for the device.
Server
Time sync with Server: Check this box to synchronize the device
time with the server. The device polls for a time change on the server
every one hour and its time will be synchronized with the server when
the devices time and the servers time differ by more than 5 seconds.

the device.
for the device.
RS485
115200).

The Access Control tab allows you to customize entrance limit settings, default
access groups, and T&A mode settings for Xpass Slim devices.



In Event Caption: Seet a caption for check-in.
5.1.5.4 Input tab

The input tab lists input settings you have specified for an Xpass Slim device.
Device: Select the Xpass Slim (or Secure I/O) device for which you will add or
modify settings.
devices, the following options are available: Input 0, Input 1, Input 2, Input
3.
(events specified with Detect Input 1-3 in the Output Setting dialog
box see section 5.1.5.5).


schedule).
5.1.5.5 Output tab

The Output tab lists output settings you have specified for an Xpass device. Buttons
at the bottom of the tab allow you to add, modify, or delete output settings. To add
or modify settings, you must specify them from the Output Setting dialog box. For
more information about configuring output settings, see section 3.10.3.1.
settings.

Setting).
2.


about command cards, see section 3.2.8.1.

section for each event.

5.1.5.8 Wiegand tab

The Wiegand tab allows you to configure the Wiegand format for an Xpass device.
Click Change Format to launch the Wiegand Configuration wizard. To activate the
Wiegand feature for an Xpass device, click the checkbox at the top right of the tab.
For more information on configuring the Wiegand format, see section 3.2.13.


card ID.
user ID.
5.1.6 Customize Settings for D-Station Devices

The sections below describe the settings available for D-Station devices. Customize the way
D-Station devices function by changing these settings to suit your particular environment

modes settings for D-Station devices.

D-Station Time
Time.
1: 1 Operation Mode: The drop-down lists in this area allow you to control
the authentication mode by schedule. For example, you can choose a
normal authentication mode for working hours and a more strict
authentication mode for hours outside the normal schedule. You can
specify authentication modes either by device or by user (see section 5.4.1).
Unless a particular mode is specified for a user, the device authentication
mode will apply.
ID/Card + Fingerprint: Set the device to require ID or card plus
fingerprint authorization (Always, or No Time).
password authorization (Always, or No Time).
ID/Card + Fingerprint/Password: Set the device to require ID or card
plus fingerprint or password authorization (Always, or No Time).
or No Time).
ID/Card + Fingerprint + Password: Set the device to require ID or
card plus fingerprint plus password authorization (Always, or No Time).
1: N Operation
1: N Schedule: Set a schedule for using fingerprint only authentication
(Always, or No Time).
1: N Operation Mode: Set a method for activating the fingerprint sensor
(Auto, Ok/Function Key, or None).
Two Sensor Mode
Fast Mode: The device will provide the quickest authentication.
Fusion Mode: Authentication is provided by a fusion algorithm that
allowes users to scan either of two registered fingers and increases the
authentication rate for each finger.
Twin Mode: Each sensor works independently to authenticate up to
two users simultaneously.

Detect Face: Set the device to capture a face image. Upon successful
authentication, the captured image is stored in the event log and can be
used later for verification purposes.
Face Fusion: Set the device to use face fusion for authentication. This setting
can improve authentication rates for some users. This setting can be used
in conjunction with either the Fast Mode or the Fusion Mode in the Two
Sensor Mode setting.
Fusion Time out: Set the device to automatically time out after a specified
number of minutes, if authentication is unsuccessful (1-20).
Interphone: Set the device to act as an interphone to allow communication
between people on either side of the door (Not Use or Use).
Other options
access cards or fingerprints (Always, or No Time). The timeout for
presenting the second authentication is 15 seconds.
Mifare
Use Template on Card: Ceck this box to use the template on the
ISO Format


D-Station devices.
Fingerprint
rejection.
Image Quality: Set the strictness of the quality check for fingerprint
scans (Weak, Normal, or Strict). If a fingerprint image is below the
specified quality level, it will be rejected.
1: N Delay: Set the delay between scans when identifying fingerprints
(0 sec to 10 sec). This delay prevents the scanner from processing the
same fingerprint more than once if a user has not yet removed his or
her finger from the scanner.


display (Yes or No).
sec).
Template Option: Displays the global fingerprint template settings.
For more information about fingerprint templates, see section 4.9.
5.1.6.3 Camera tab

The Camera tab allows you to control how the camera is used for authorization
purposes. In the Timezone field, select a timezone for the specified event. Click Add
to select an event that will activate the camera. Click Apply to save your settings.

5.1.6.4 Network tab

The Network tab allows you to customize network and server settings for D-Station
devices.
TCP/IP Setting
WLAN
IP
Server
Not use: Click this radio button do disable server settings.
SSL: Displays the status of SSL for the server connection.

RS485 Network
or Slave). For more information about RS485 modes, please see
sections 3.2.1 and 3.2.2.
RS485
115200).
RS232
115200).
USB Setting: Click the radio buttons to enable or disable the USB port on
the D-Station device.

access groups for a D-Station device.


5.1.6.6 Interphone tab

The Interphone tab allows you to set the device to act as an interphone to allow
Type: Select one of the following options:

Aanlogue Interphone: Choose this option to enable the analogue
interphone.
IP Interphone: Choose this option to enable the VoIP feature. A
telephone is required.
BioStar Videophone: Choose this option to enable the videophone
feature that supports both video and voice calls. The supplied PC
software is required. The BioStar vidoephone works only with the
device firmware version of FaceStation V1.0 or later.
When you select IP Interphone in the Type drop-down list, specify the following
settings:
VOIP Server IP: Specify an IP address for VOIP server.
VoIP Display Name: Specify a name to use for communication through the
interphone.
VoIP Phone Number: Specify a phone number for the interphone.
VoIP ID: Specify a user name to access the VoIP server.
VoIP Password: Specify a password to access the VoIP server.
Speaker Gain: Specify the volume of the speaker.
Mic Gain: Specify the volume of the microphone.
When you select Videophone in the Type drop-down list, specify the following
settings:
Mode: Specify the videophone purpose (Single or Extension).
Door Control: Check this option if the videophone is used for door access.
Device Password: Enter the videophone device password.

5.1.6.7 Input tab

The input tab lists input settings you have specified for a D-Station device. Buttons
Device: Select the D-Station device for which you will add or modify settings.
(For the events specified with Detect Input 0-3 in the Output
inputs. To enable communication again, an administrator must provide
authentication at the device.
(Always or No Time).

5.1.6.8 Output tab

The Output tab lists output settings you have specified for a D-Station device.
section 3.10.3.1.
settings.
Setting).
2.


Current Count: Indicates the total number of user IDs and access cards that
have been registered.
Reserved: Indicates the remaining number of user IDs and access cards that
can be registered.


The Display/Sound tab allows you to customize the D-Station display and event
Apply to Others.
Display/Sound
the idle screen.
Backlight Timeout: Set the length of time before the display goes
dim.
Theme: Set a display theme.
Background: Set the type of background for the BioStation display
BioStation display. After creating a notice, you can click Apply to apply
Type: Set the type of background for the BioStation display (Logo or
Notice). Supported file types (JPG, GIF, BMP, and PNG) cannot exceed
800x427 pixels for Notices and 800x327 pixels for Logos. Only one
image at a time can be used as a logo or notice.

sound file. Click Add to add new sound files, Delete to remove sound files,
or Play to preview a selected sound file.
5.1.6.11 T&A tab

The T&A tab allows you to configure the mode and key settings for a D-Station

Event Fix: The device will perform only the specified T&A function. In
this mode, each sensor can work independently. You can set an event
for each sensor.
a T&A event (F1-F4, EXT01-EXT12). If you are using the Event Fix
event.


section 3.7.1.

The Wiegand tab allows you to configure the Wiegand format for a D-Station


Wiegand In/Out: Assign the Wiegand input or output:
Wiegand (User) In: The ID field of the Wiegand string is interpreted
as a user ID.
Wiegand (Card) In: The ID field of the Wiegand string is interpreted
as a card ID.
Wiegand (User) Out: Inserts the user ID of the authenticated user in
the ID field of the Wiegand string.
Wiegand (Card) Out: Inserts the card ID of the authenticated user in
5.1.7 Customize Settings for X-Station Devices

The sections below describe the settings available for X-Station devices. Customize the way
X-Station devices function by changing these settings to suit your particular environment

modes settings for X-Station devices.
X-Station Time

Time.
1: 1 Operation Mode: The drop-down lists in this area allow you to control
mode will apply.
Card Only: Set the device to require only card authorization (No Time,
First Shift, or Always).
password authorization (No Time, First Shift, or Always).
Private Auth: Set the device to allow a private authorization method (Disable
or Enable). If enabled, the authentication mode of the user will be
determined by a users Authorization setting, which is located on the
Details tab. If disabled, the authentication mode will be determined by
operation mode settings of the device.
Double Mode: Set the device to require authentication of two users access
cards or fingerprints (Always, or No Time). The timeout for presenting the
second authentication is 15 seconds.
Server Matching: Enable this setting to perform card ID matching at the
BioStar server, instead of the device. When this mode is enabled, the device
will send card ID to the server to verify a match. This mode is useful when
you have more users than can be downloaded to a device or user
information cannot be distributed due to security concerns.
Auth Timeout: Set the length of time before the device will timeout when
trying to identify an ID match (5, 10, 15, 20, or 30 sec).
authentication, the captured image is stored in the event log and can be
used later for verification purposes.
Mifare
Use Data Card: Check this box to use the template on the MIFARE
card for authorization.

Card ID Format
5.1.7.2 Camera tab

5.1.7.3 Network tab

The Network tab allows you to customize network and server settings for X-Station
devices.
TCP/IP Setting
(Disable, or Ethernet).
IP

Server
RS485 Network
RS485
115200).

access groups for an X-Station device.




interphone.
settings:
interphone.


settings:
5.1.7.6 Input tab

The input tab lists input settings you have specified for an X-Station device. Buttons
Device: Select the X-Station device for which you will add or modify settings.
(For the events specified with Detect Input 0-3 in the Output


(Always, First Shift, or No Time).
5.1.7.7 Output tab

The Output tab lists output settings you have specified for an X-Station device.
section 3.10.3.1.
settings.
Limited, Admin Auth Success, Tamper On, Door Opened, Door Closed,


Setting).
2.

The Black list tab allows you to register user IDs or access card numbers and
been registered.
registered.


The Display/Sound tab allows you to customize the X-Station display and event
Apply to Others.
Display/Sound
Custom).
the idle screen.
Back Light Timeout: Set the length of time before the display goes
dim (Infinite, 10, 20, 30, 40, 50, or 60 sec).
Theme: Set a display theme (Theme 1-3).
Resource File: Set the language resource file to use for the
X-Station interface (No Change, English, Korean, or Custom). To use a
language resource file other than English or Korean, select Custom and
then click the ellipsis () button to locate the resource file.
Background: Set the type of background for the X-Station display
X-Station display. After creating a notice, you can click Apply to apply
Volume: Set the volume of the X-Station device (0% to 100%).


Clock Display: Set to display the current time on the device (Enable or
Disable).
Click Add to locate and add a new image file. To delete an existing image,
click the image name and then click Delete.
Type: Set the type of background for the X-Station display (Logo,
Notice, or Slide Show). Supported file types (JPG, GIF, BMP, and PNG)
cannot exceed 240x320 pixels for Notices and 240x320 pixels for
Logos. Only one image at a time can be used as a logo or notice.
event from the list and then click Add to locate and add a new sound file.
Click Delete to remove custom sound files or Play to preview a custom
sound file.
5.1.7.10 T&A tab

The T&A tab allows you to configure the mode and key settings for an X-Station



a T&A event (*1-*15). If you are using the Event Fix mode, you can
click the checkbox to the right to designate a fixed event.
down list. For more information on creating a timezone, see section
3.7.1.
out event option. If this option is enabled, users using the
appropriate keys will be regarded arriving or leaving on time at work
even though they actually come late or leave early. If you enable the
Only Result option, they appear being on time on T&A reports but
their work time will be calculated correctly based on their actual check
in/out time. If you choose Out, you can enable the Add work time
after this event option. If this option is enabled, users using the
appropriate key will be considered working for the remainder of the
time slot even though they leave the office early.


The Wiegand tab allows you to configure the Wiegand format for an X-Station
more information on configuring the Wiegand format, please see section 3.2.13.
ID data (Legacy or Extended). The Legacy mode will process ID data from
networked devices and RF card readers in the same way (this is the typical
function of previous versions of BioStar). The Extended mode will allow RF
card readers to operate independently, which allows them to be associated
with doors, included in zones, and leave logs with their own device IDs.
Wiegand In/Out: Assign the function of the Wiegand input or output:
as a user ID.
as a card ID.
5.1.8 Customize Settings for BioStation T2 Devices

The sections below describe the settings available for BioStation T2 devices. Customize the
way BioStation T2 devices function by changing these settings to suit your particular


modes settings for BioStation T2 devices.
BioStation T2 Time
Time.
ID Operation Mode: The drop-down lists in this area allow you to control
mode will apply.
ID + Fingerprint: Set the device to require ID plus fingerprint
authorization (Always, or No Time).
ID + Password: Set the device to require ID plus password
ID + Fingerprint/Password: Set the device to require ID plus
fingerprint or password authorization (Always, or No Time).

ID + Fingerprint + Password: Set the device to require ID plus

fingerprint plus password authorization (Always, or No Time).
Card Operation Mode
or No Time).
Card + Fingerprint: Set the device to require card plus fingerprint
Card + Password: Set the device to require card plus password
Card + Fingerprint/Password: Set the device to require card plus
fingerprint or password authorization (Always, or No Time).
Card + Fingerprint + Password: Set the device to require card plus
fingerprint plus password authorization (Always, or No Time).
Fingerprint Operation Mode
Fingerprint: Set the device to require only fingerprint authorization
(Always, or No Time).
Fingerprint + Password: Set the device to require fingerprint plus
password authorization (Always, or No Time).
Func Key + Fingerprint: Set the device to require function key plus
fingerprint authorization (Always, or No Time).
Func Key + Fingerprint + Password: Set the device to require
function key plus fingerprint plus password authorization (Always, or
No Time).
Other options
IDs, access cards or fingerprints (Always, or No Time). The timeout for
presenting the second authentication is 15 seconds.
authentication, the captured image is stored in the event log.
Server Matching: Enable this setting to perform user ID, fingerprint or
card ID matching at the BioStar server, instead of the device. When this
mode is enabled, the devices will send the user ID, fingerprint
template or card ID to the server to verify a match. This mode is useful
when you have more users than can be downloaded to a device or
user information cannot be distributed due to security concerns.
timeout when trying to identify a fingerprint match within the device
itself or via the server (3, 7, 10, 15, 20, 30 sec).


Mifare
Card ID Format
Format Type: Set the type of pre-processing to occur on card ID
data (Normal or Wiegand). If Normal is selected, the card ID data
will be processed in its original form. If Wiegand is selected,
devices will interpret card ID data according to the Wiegand format
settings.
Byte Order: Specify whether to swap ID card data between cards
and devices by most significant byte (MSB) or least significant byte
(LSB).
In Double mode, setting option which includes an admin user is
supported. In Double mode, door relay will not open unless an
admin user authenticates within 15 seconds after a normal user
authenticates. If this option is not activated, the door relay will open
when other two users, regardless of whether being a normal user or
an admin user.
BioStation T2 1.3, FaceStation 1.3, BioEntry Plus 1.6, BioEntry W 1.2,
BioLite Net 1.4, Xpass 1.3.
Use Wiegand Card Bypass: This feature makes the device to send out
Card CSN according to Wiegand setting of BioStar without having to
conduct a matching. This is designed to be used as a dummy reader
in a connection with a third party access control unit through
Wiegand. When a card data input is made, the device sends out the
data through Wiegand without going through a matching process.
BioStation T2 1.3, FaceStation 1.3, BioEntry Plus 1.6, BioEntry W 1.2,
BioLite Net 1.4, Xpass 1.3.

BioStation T2 devices.

Fingerprint
rejection.
T2 display (Yes or No).
Template Option: Displays the global fingerprint template settings.
For more information about fingerprint templates, see section 4.9.
5.1.8.3 Camera tab


5.1.8.4 Network tab

BioStation T2 devices.

TCP/IP Setting
WLAN
for a WLAN, see section 3.2.4.
IP
Server
RS485 Network
RS485
115200).
RS232
115200).
USB: Click the radio buttons to enable or disable the USB port on the
BioStation T2 device.
USB Memory: Click the radio buttons to enable or disable the USB memory
on the BioStation T2 device.


access groups for a BioStation T2 device.

gained entry, the device will reject the users ID, access card, or
fingerprint authorization for the time period specified here.

Type select one of the following options:

interphone.


device firmware version of BioStation T2 V1.1 or later.
settings:
VoIP Server IP: Specify an IP address for the VoIP server.
interphone.
VoIP Speaker Gain: Specify the volume of the speaker.
VoIP Mic Gain: Specify the volume of the microphone.
5.1.8.7 Input tab

The input tab lists input settings you have specified for a BioStation T2 device.
Device: Select the BioStation T2 device for which you will add or modify
settings.

5.1.8.8 Output tab

The Output tab lists output settings you have specified for a BioStation T2 device.
section 3.10.3.1.
settings.


Setting).
2.
Priority: Set a priority for the event. Only an event with an equal or higher priority
(1 is the highest) can override a previous event. For example, a priority 2 alarm on
event (activate) can be overridden only by an alarm off (deactivate) event with a
priority of 1 or 2.


Current Count: The total number of the user IDs and access cards that have
been registered.
Reserved : The remaining number of user IDs and access cards to be
registered.

The Display/Sound tab allows you to customize the BioStation T2 display and event
Apply to Others.
Display/Sound
Custom).
the idle screen.
dim.
Theme: set a display theme.
Use Voice: Set the device to notify you with voice messages (Disable
or Enable).
Resource File: Set the language resource file to use for the BioStar
interface (No Change, English, Korean, or Custom). To use a language
Background: Set the type of background for the BioStation T2 display
(Logo, Notice, or Slide Show). Supported file types (JPG, GIF, BMP, PNG
and PDF) cannot exceed 480x800 pixels each. Only one image at a

time can be used as a logo or notice, while up to 16 images can be

Disable).
Type: Set the type of background for the BioStation display (Logo or
Notice). Supported file types (JPG, GIF, BMP, PNG and PDF) cannot
exceed 480x800 pixels for Notices and 480x800 pixels for Logos. Only
one image at a time can be used as a logo or notice.
5.1.8.11 T&A tab

The T&A tab allows you to configure the mode and key settings for a BioStation T2


event.
section 3.7.1.


The Wiegand tab allows you to configure the Wiegand format for a BioStation T2
as a user ID.
as a card ID.
5.1.9 Customize Settings for FaceStation Devices

The sections below describe the settings available for FaceStation devices. Customize the
way FaceStation devices function by changing these settings to suit your particular

modes settings for FaceStation devices.

FaceStation Time
Sync with Host PC Time: Check this box to automatically synchronize
the device time with the time of the host computer.
ID Operation Mode: The drop-down lists in this area allow you to control
mode will apply.
ID + Face: Set the device to require ID plus face recognition for
authorization (Always, New Time Zone, or No Time).
ID + Password: Set the device to require ID plus password
ID + Face/Password: Set the device to require ID plus face
recognition or password authorization (Always, New Time Zone, or No
Time).
ID + Face + Password: Set the device to require ID plus face
recognition plus password authorization (Always, New Time Zone, or
No Time).

Card Operation Mode

New Time Zone, or No Time).
Card + Face: Set the device to require card plus face recognition for
Card + Password: Set the device to require card plus password
Card + Face/Password: Set the device to require card plus face
recognition or password authorization (Always, New Time Zone, or No
Time).
Card + Face + Password: Set the device to require card plus face
recognition plus password authorization (Always, New Time Zone, or
No Time).
Face Operation Mode
Face: Set the device to require only face recognition for authorization
(Always, New Time Zone, or No Time).
Face + Password: Set the device to require face recognition plus
password authorization (Always, New Time Zone, or No Time).
Func Key + Face: Set the device to require function key plus face
recognition for authorization (Always, New Time Zone, or No Time).
Func Key + Face + Password: Set the device to require function key
plus face recognition plus password authorization (Always, New Time
Zone, or No Time).
Face + Func Key: Set the device to require face recognition plus
function key authorization, and then immediately proceed to T&A
functions (Always, New Time Zone, or No Time).
Face + Password + Func Key: Set the device to require face
recognition plus password plus function key authorization, and then
immediately proceed to T&A functions (Always, New Time Zone, or No
Time).
Other options
IDs, access cards or face recognitions (Always, New Time Zone, or No
Time). The timeout for presenting the second authentication is 15
seconds.
Detect Face: Set the device to capture a face image (Use or Not Use).
Upon successful authentication, the captured image is stored in the
event log.

timeout when trying to identify a fingerprint match within the device
itself or via the server (3, 7, 10, 15, 20, 30 sec).
Mifare
Use Template on Card: Not available with FaceSation devices.
View Mifare Layout: Not available with FaceSation devices.
Card ID Format
5.1.9.2 Face tab

The Face tab allows you to customize face recognition settings for FaceStation
devices.
Security Level: Set the security level to use for face recognition (Normal,
Secure, or Most Secure). Keep in mind that as the security level is increased,
so too is the likelihood of a false rejection.
Enroll Sensitivity: Set the sensitivity of the face recognition system (0 [Min]
to 9 [Max]). A higher sensitivity setting will result in easier face recognition,
but also increases the sensitivity to external visual noise.
Use Templete Image: Set whether or not to display user face template
images in the FaceStation device.
5.1.9.3 Camera tab


5.1.9.4 Network tab

FaceStation devices.
TCP/IP Setting
WLAN
IP

Server
RS485 Network
RS485
115200).
RS232
115200).
USB: Click the radio buttons to enable or disable the USB port on the
FaceStation device.
USB Memory: Click the radio buttons to enable or disable the USB memory
on the FaceStation device.


access groups for a FaceStation device.

gained entry, the device will reject the users ID, access card, or
fingerprint authorization for the time period specified here.



interphone.
settings:
interphone.
settings:

5.1.9.7 Input tab

The input tab lists input settings you have specified for a FaceStation device.
Device: Select the FaceStation device for which you will add or modify
settings.
communicate with the BioStar server or process face or card inputs. To
enable communication again, an administrator must provide

5.1.9.8 Output tab

The Output tab lists output settings you have specified for a FaceStation device.
section 3.10.3.1.
settings.
Fail, Anti-passback Fail, Access Not Granted, Entrance Limited, Admin
Auth Success, Tamper On, Door Opened, Door Close, Forced Open Door,
Held Open Door, Detect Input #1-3).
Setting).
2.

Fail, Anti-passback Fail, Access Not Granted, Entrance Limited, Admin
Auth Success, Tamper On, Door Opened, Door Close, Forced Open Door,
Held Open Door, or Detect Input #1-3).
Priority: Set a priority for the event. Only an event with an equal or higher
priority (1 is the highest) can override a previous event. For example, a
priority 2 alarm on event (activate) can be overridden only by an alarm
off (deactivate) event with a priority of 1 or 2.

The Display/Sound tab allows you to customize the FaceStation display and event
Apply to Others.
Display/Sound
Custom).
the idle screen (Infinite, 10 sec, 20 sec, or 30 sec).
dim (Infinite, 10 sec, 20 sec, 30 sec, 40 sec, 50 sec, or 60 sec).
Theme: set a display theme (Theme 1-4)

Use Voice: Set the device to notify you with voice messages (Disable
or Enable).
Resource File: Set the language resource file to use for the BioStar
interface (No Change, Korean, English, or Custom). To use a language
Background: Set the type of background for the FaceStation display
(Logo, Notice, Slide Show, or PDF). Supported file types (JPG, GIF, BMP,
PNG and PDF) cannot exceed 480x800 pixels each. Only one image at
a time can be used as a logo or notice, while up to 16 images can be
Volume: Set the volume of the FaceStation device (0% to 100%).
message will be displayed (0.5-5 sec).
Disable).
Type: Set the type of background for the FaceStation display (Logo,
Notice, Slide Show, or PDF). Supported file types (JPG, GIF, BMP, PNG
and PDF) cannot exceed 480x800 pixels for Notices and 480x800 pixels
for Logos. Only one image at a time can be used as a logo or notice.

5.1.9.10 T&A tab

The T&A tab allows you to configure the mode and key settings for a FaceStation

event.
down list. For more information on creating a timezone, see section
3.7.1.


The Wiegand tab allows you to configure the Wiegand format for a FaceStation
as a user ID.


as a card ID.
5.2 Customize Door Settings

The sections below describe the settings available for doors that have been added to the
BioStar system. Customize the way these doors function by changing settings to suit your
particular environment and operational needs. To access the tabs described below, click
Doors in the shortcut pane, then click a door name.
5.2.1 Details tab

The Details tab allows you to specify which devices are used on the inside or outside of a
door, how the devices control the door, and anti-passback features. When connecting two
devices to a single door, the devices should be connected to each other by RS485. In this
case, the I/O ports of only one device can be used. Specify which devices I/O ports to use in
the IO Device drop-down list.
Inside Device: Select a device to use on the inside of the door.

Outside Device: Select a device to use on the outside of the door.
Unlock Time: Select a schedule when the door should normally be unlocked. During
this time, door relays are active.
Lock Time: Select a schedule when the door should normally be locked. During this
time, door relays are inactive.

IO Device: When using two devices on a single door, specify which devices IO ports will
be used.
Door Relay: Select a door relay.
Exit Button: Select a device input to use for an exit button (Disable or Input 0 and Input
1 for each device added).
(Switch Type): Set the normal position of the input used for an exit button (N/O-
normally open or N/C-normally closed).
Door Status: set an input for a sensor that detects the current status of the door.
(Switch Type): Set the normal position of the input used for a door status sensor (N/O-
normally open or N/C-normally closed).
Door Open Period (sec): Set the duration (in seconds) that a door relay should be
activated when a door is opened. After this duration, the relay will stop sending the
signal to open the door. The default is three seconds.
Door Open Alarm (sec): Set the duration (in seconds) that a door can remain open
before an alarm will sound.
Driven by: Select types of events that will trigger associated devices to open the door.
All Events (default): Associated devices will open the door on any successful
authorization events.
TNA + AUTH: Associated devices will open the door on successful T&A or
credential authorization events or T&A authorization events. To use this option, you
must select the Use Relay checkbox in the T&A tab. This option is only available for
BioStation, BioLite Net, D-Station, X-Station, BioStation T2, and FaceStation devices.
For more information about configuring T&A settings, see section 5.1.1.9, 5.1.3.9,
5.1.6.11, 5.1.7.10, and 5.1.8.11.
AUTH: Associated devices will open the door only on successful credential
TNA: Associated devices will open the door only on successful T&A authorization
events. To use this option, you must select the Use Relay checkbox in the T&A tab.
This option is only available for BioStation, BioLite Net, D-Station, X-Station,
BioStation T2, and FaceStation devices. For more information about configuring
T&A settings, see section 5.1.1.9, 5.1.3.9, 5.1.6.11, 5.1.7.10, and 5.1.8.11.
Disabled: Associated devices will not open the door, regardless of the attempted
Closed by: Select an option for closing the door.
Open period: The BioStar system will close the door after the period specified in
the Door Open Period (sec) field.
Open period+Status: The BioStar system will attempt to close the door based on
door status (if you have connected door sensors and the system can detect that the
door is open). If door sensors are not connected or the system is unable to detect
the door status, the system will close the door after the period specified in the Door
Open Period (sec) field. This setting is useful when used with revolving doors, for

example, to prevent someone from following an authorized person through the

door.
Anti-passback: Click the checkbox to activate the anti-passback feature (only available
when using both an inside and an outside device).
Device Name: This field is populated automatically.
Device IP: This field is populated automatically.
APB Type: Set the type of anti-passback restriction to use (Soft or Hard).
Reset Time (min): Set the duration (in minutes) that must pass before the anti-
passback status is reset. The default reset time is 0at this setting, the anti-
passback status will not be reset.
Unlock Trigger Option
Unlock Trigger Option: Unlock Trigger is supported in the Details tab in the door
setting. This feature allows the door to be remained open during Unlock Time only
after an Admin User or Normal User identification.
Note: Supported Firmware Versions: BioStation 1.93, BioStation T2 1.3, FaceStation
1.3, BioEntry Plus 1.6, BioEntry W 1.2, BioLite Net 1.4, Xpass 1.3..
Note: Unlock Trigger is not supported when two devices (Host/Slave device or 3rd
Party Wiegand reader) are configured for one door and Unlock Trigger was made
from the slave device. And when the case that 3rd Party Wiegand reader is configured
for one door is not supported. And its supported only when a triger was made from
one Host device.
Minimum Input Duration
Minimum Input Duration: This feature can be activated from Details tab in the door
setting. When this option is in use, the device accepts input signal only when the
signal continues more than a certain period of time designated by the FW fix. This
option is activated with the latest FW and shown Use or Not Use.
Note: Supported Firmware Versions: BioStation 1.93, BioStation T2 1.3, FaceStation
1.3, BioEntry Plus 1.6, BioEntry W 1.2, BioLite Net 1.4, Xpass 1.3..
5.2.2 Alarm tab

The Alarm tab allows you to specify alarm actions for doors that are forced open or held
open. A forced open alarm occurs when a door is forcibly opened without any
authentication at the device. A held open alarm occurs when a door remains open longer
than the duration specified in the system settings.

Action
Program Sound: Activate and select a sound from the drop-down list to be
emitted by the BioStar program. Then, specify the duration (play count) of the
sound in seconds. If you set the Play Count to 0, the specified sound will play until
someone with administrative privileges manually stops the sound via the Realtime
Monitoring tab in the Monitoring pane. To add custom sounds to the list, see
section 3.10.1.2.
Device Sound: Activate and select a sound to be emitted by devices connected to
the door.
Send Email: Activate and setup emails to be sent by the system. For more
information about sending alert emails, see section 3.10.2.
Output Device: Activate and select a device to output an alarm signal.
Output Port: Select an output port to use when sending the alarm signal.
Output Signal: Select an output signal to send.
5.3 Customize Zone Settings

Customize the way zones function by changing the settings to suit your particular
environment and operational needs. To access the tabs described below, click Doors in the
shortcut pane, then click a zone name.
5.3.1 Customize Settings for Anti-Passback Zones

The sections below describe the settings available for anti-passback zones. Customize the
way the zone functions by changing these settings to suit your particular environment and
operational needs.

5.3.1.1 Details tab

The Details tab allows you to specify which anti-passback type to use for a zone
and the reset period for the anti-passback feature.
APB Type: Select a type of anti-passback restriction to apply (Soft or Hard).

Reset Time (min): Set the duration (in minutes) that must pass before the
anti-passback status is reset. The default reset time is 0at this setting, the
anti-passback status will not be reset.
In case of Disconnected: Set how doors in the zone should behave if
communication is lost between the master and member devices.
5.3.1.2 Alarm tab

The Alarm tab allows you to specify alarm actions and an output device for an anti-
passback zone.
Action
Program Sound: Activate and select a sound from the drop-down list
to be emitted by the BioStar program. Then, specify the duration
(play count) of the sound in seconds. If you set the Play Count to 0,
the specified sound will play until someone with administrative
privileges manually stops the sound via the Realtime Monitoring tab in
the Monitoring pane. To add custom sounds to the list, see section
3.10.1.2.
Device Sound: Activate and select a sound to be emitted by devices
connected to the door.
Send Email: Activate and setup emails to be sent by the system. For
more information about sending alert emails, see section 3.10.2.
Output Device: activate and select a device to output an alarm signal.

Output Port: Select an output port to use when sending the alarm
signal.
5.3.1.3 Access Group tab

The Access Group tab allows you to specify access groups that can bypass normal
restrictions for the zone. To grant bypass rights to an access group, select a group
and click Apply at the bottom right of the Zone pane.
5.3.2 Customize Settings for Entrance Limit Zones

The sections below describe the settings available for entrance limit zones. Customize the
operational needs.

5.3.2.1 Details tab

The Details tab allows you to specify entrance limits and a schedule for the zone
restrictions.
Entrance Limit Zone Setting: Click the checkbox to enable an entrance limit
setting, and then specify the effective hours for the entrance limit.
Max Number of Entrance: Set the maximum number of entries allowed
during the specified time limit.
Timed APB (min): Specify a time limit for re-entry into a zone.
In case of Disconnected: Set how doors in the zone should behave if
communication is lost between the master and member devices.
5.3.2.2 Alarm tab

The Alarm tab allows you to specify alarm actions and an output device for an
entrance limit zone.
Action
3.10.1.2.

signal.

The Access Group tab allows you to specify access groups that can bypass normal
restrictions for the zone. To grant bypass rights to an access group, select a group
and click Apply at the bottom right of the Zone pane.
5.3.3 Customize Settings for Alarm Zones

The sections below describe the settings available for alarm zones. Customize the way the
zone functions by changing these settings to suit your particular environment and
operational needs.
5.3.3.1 Details tab

The Details tab allows you to specify alarm delays and arm/disarm types for alarm
zones.

Delay (sec)
Arm: Set the length of time (in seconds) to delay before arming the
zone.
Disarm: Set the length of time (in seconds) to delay before disarming
the zone.
Arm/Disarm Type: Specify settings for arming or disarming zones. For more
information for configuring arm and disarm settings, see 3.5.2.5. For more
information on setting up alarms, see section 3.10.
External Input/Out: Specify settings for enabling the BioStar system to
antomatically arming or disarming zones. For more information on
configuring external input/output settings, see 3.5.2.6. For more
information on setting up alarms, see section 3.10.
5.3.3.2 Alarm tab

The Alarm tab allows you to specify alarm actions and an output device for an
alarm zone.
Action
3.10.1.2.
signal.


The Access Group tab allows you to specify access groups that can arm and disarm
zones. To grant disarm authorization to an access group, select a group and click
Apply at the bottom right of the Zone pane.
5.3.4 Customize Settings for Fire Alarm Zones

The sections below describe the settings available for fire alarm zones. Customize the way
the zone functions by changing these settings to suit your particular environment and
operational needs.
5.3.4.1 Details tab

The Details tab allows you to add or delete devices in the Device List and inputs to
the Input List. To add or delete devices, see section 3.5.2.2.

5.3.4.2 Alarm tab

The Alarm tab allows you to specify alarm actions and an output device for a fire
alarm zone.
Action
3.10.1.2.
signal.

5.3.5 Customize Settings for Access Zones

The sections below describe the settings available for access zones. These zones are used to
synchronize user data, so the Alarm and Access Group tabs are unavailable. Customize the
operational needs.
5.3.5.1 Details tab

The Details tab allows you to add devices to the Device List.
Synchronize User Info: Click this checkbox to automatically propagate user

information to other devices.
Synchronize Log Data: Click this checkbox to automatically write all log
records to the master device (for member devices in the zone).
Synchronize Time: Click this checkbox to synchronize the time of devices in
the zone.

5.3.6 Customize Settings for Muster Zones

The sections below describe the settings available for muster zones. These zones are used to
monitors user locations, so the Alarm tab is unavailable. Customize the way the zone
functions by changing these settings to suit your particular environment and operational
needs.
5.3.6.1 Details tab

The Details tab allows you to add devices to the Device List.
Muster Zone Type: By default, set to Manual. You can check for the people
who were present in a specified area for a specific time period. Please see
4.1.1 to see how to manually check attedance of people.
Tracking Time (hour): Specify how far (in hours) people are monitored for
their in/out activities in the zone. For example, if you set this value to 8, you
can track a record of attendace since 8 hours ago.


The Access Group tab allows you to specify access groups that belong to a muster
zone. To assign access groups to a muster zone, select a group and click Apply at
the bottom right of the Zone pane.

5.3.7 Customize Settings for Interlock Zones

The sections below describe the settings available for interlock zones. Customize the way the
zone functions by changing these settings to suit your particular environment and
operational needs.
Interlock zones works only with the following device firmware versions:
BioStation V1.9 or later, BioEntry Plus V1.5 or later, BioEntry W V1.0 or later, BioLite Net
V1.3 or later, and Xpass V1.2 or later.
Interlock zones are not supported for BioStation T2, X-Station, D-Station, and
FaceStation.
5.3.7.1 Details tab

The Details tab allows you to specify which doors to use for either side of the
interlock zone. Once added, the door names and device IDs will appear in the
Device List.
Door 1: Click the ellipsis () button to select door 1 of the interlock area.
Doors without associated devices cannot be added to the interlock zone.
Door 2: Click the ellipsis () button to select the device on door 2 of the
interlock area. Doors without associated devices cannot be added to the
interlock zone.
5.4 Customize User Settings

Customize various settings for users, including personal details, fingerprint information, and
access card information. To access the tabs described below, click Users in the shortcut
pane, then click a user name.

5.4.1 Details Tab

The Details tab allows you to specify personal information about a user and the valid dates
of a user account. To edit these fields, see section 4.4.3.
ID: Enter an identification number for a user.

Start Date: Set a beginning date that the user can obtain authorization via the BioStar
system.
Expiry Date: Set a date that the user's account will expire (you can also specify the hour
that the account will expire).
Private Auth Mode: Set the authorization method for the user (Device Default,
Fingerprint, Fingerprint + Password, Card Only, Card + Fingerprint, Card + Password,
Card + Fingerprint/Password, Card + Fingerprint + Password, ID + Fingerprint, ID +
Password, ID + Fingerprint/Password, ID + Fingerprint + Password). If you set the
method to Device Default, the authentication mode will be determined by operation
mode settings of the device.
Title: Select a title for the user (Guest, President, Director, General Manager, Chief,
Assistant Manager, or custom title).
Mobile: Enter a mobile telephone number for a user.
Genders: Select a user's gender.
Date of Birth: Select a user's date of birth from the drop-down calendar.

5.4.2 Fingerprints Tab

The Fingerprints tab allows you to specify which type of scanner to use for enrollment and
the security level to apply. This tab can also be used to test for fingerprint matches and
register duress fingerprints. For more information about registering fingerprints, see section
3.6.2.
Enroll Device: Select a device to use for scanning fingerprints.

1: 1 Security Level: Select a security level to use for fingerprint authorization (Device
Default and Lowest [1/1,000] to Highest [1/10,000,000]). Keep in mind that as the
security level is increased, so too is the likelihood of a false rejection.
Duress: set a fingerprint template to be used as a duress finger (the duress finger will
activate alarms when used to gain entry).
5.4.3 Face Tab

The Face tab allows you to specify a FaceStation device to use for storing face templates of
users. When you sucessfully capture faces(up to 5 per user), the FaceStation device transfers
25 face templates to the BioStar. During authentication, any face template that receives a
higher score than one of the registered face templates will replace the old one. For more
information about capturing face images, see section 3.6.3.
Enroll Device: Select a device to use for capturing face images.

5.4.4 Face (Fusion) Tab

The Face tab allows you to specify a D-Station device to use for capturing face images of
users. For more information about capturing face images, see section 3.6.3.
Enroll Device: Select a device to use for capturing face images.
5.4.5 Card Tab

The Card tab allows you to specify card types and IDs and issue cards to users. For more
information about issuing cards, see section 3.6.3.
Card Type: Select a type of access card to issue (Mifare CSN, Mifare Template, EM 4100,
HID Prox, iCLASS CSN, or iCLASS Template).
Card ID: Displays the card ID number when a card is issued.
Custom ID: Enter a custom ID for the card.

5.4.6 T&A Tab

The T&A tab allows you to specify which shifts, holiday rules, and leave periods apply to a
user. To add new details, click Add at the bottom of the tab. To save changes to time and
attendance settings, you must click Apply at the bottom of the tab. You can also remove
entries by highlighting the entry and clicking Delete. For more information about
configuring time and attendance, please see section 3.9.
Shift Management: Specify which shifts apply to the user.

Holiday Rules Management: Specify which holiday rules apply to the user.
Leave Management: Specify leave for the user.

06
Technical Support
If you have any questions regarding this document or BioStar software, please contact technical
support at [email protected].
Please provide the following information for prompt and easy assistance:
Contact information and available times
Version of BioStar and device model name (e.g. BioStar 1.8, BioStation)
Error messages and description on problems

ndex
Glossary
access card: A card that can be used to grant or restrict access to a specific area. BioStar supports
MIFARE, EM4100, HID proximity, iCLASS, and FeliCa cards. See also: proximity card.
access control system: A system of physical mechanisms and controls that permit or deny access to a
particular resource or physical area. BioStar is an IP-based biometric access control system.
alarm zone: A grouping of devices that is used to protect a physical area. BioStar monitors input
points in an alarm zone and triggers alarms when intrusion or tampering is detected.
anti-passback: A security protocol that prevents a user from providing unauthorized entrance to
another user via an access card or fingerprint. See also: timed anti-passback.
biometrics: Biometrics refers to the use of physical characteristics for verification or authorization.
BioStar incorporates Supremas award-winning fingerprint recognition technology to provide biometric
authentication of a user's identity and authorization to gain access to restricted areas.
bypass group: A group of users that can bypass normal restrictions for a zone.
client: BioStar client software allows an operator to connect remotely to the BioStar server and control
connected devices. An operator ID and password are required to access the system via a client.
department: A division of an organization used to group employees. The use of departments is not
necessary, but may be helpful to organize large numbers of employees.
device: In this guide, the word "device" refers to any Suprema product supported by the BioStar
system. Supported devices include BioStation, BioStation Mifare, BioStation HID, DStation, BioEntry
Plus/BioEntry W, BioEntry Plus Mifare/BioEntry W Mifare, BioEntry Plus iCLASS, BioEntry Plus HID,
BioLite Net, Xpass, and BioMini USB terminals, as well as the Secure I/O device.

Glossary
distributed intelligence: In the BioStar system, the authorization database is distributed to each
terminal, so that authorization is faster and can continue even when other parts of the system are
offline.
door: Doors are the physical barriers that provide entry into a building or space. At least one device
must be connected to a door to provide access control, but two devices can be connected to support
anti-passback and other features, such as door relays, alarm relays, exit switches, and sensors.
duress finger: This term refers to an enrolled fingerprint that will activate silent alerts when a
candidate is under duress. In the typical duress scenario, a perpetrator forces the candidate to gain
access by force or threat of harm. The candidate gains access by means of his or her "duress finger,"
which allows access and simultaneously triggers the alarm or alert actions you specify.
enrollment: The process of creating a user account and capturing images of fingerprints or issuing
access cards.
entrance limit: The maximum number of times a user can gain authorization to a specific area. The
entrance limit can be related to a time period so that users are limited to certain number of entries
during office hours, for example.
ESSID: Extended Service Set ID. The ESSID is the name of a wireless network access point. It allows one
wireless network to be clearly distinguishable from another. ESSID is one type of SSID (the other being
BSSID).
face recognition -The automated process of validating a claimed identity based on the image of a
face. BioStar extracts and analyzes the facial features such as the skin texture and the shapes of the
face, eyes, nose and mouth from a captured face image and compares them with those of all the
registered persons.
false acceptance rate: The false acceptance rate (FAR) is a measure of the likelihood that a biometric
security system will incorrectly accept an access attempt by an unauthorized user. A system's FAR
typically is stated as the ratio of the number of false acceptances to the number of identification
attempts.
false rejection rate: The false rejection rate (FRR) is a measure of the likelihood that a biometric
security system will incorrectly reject an access attempt by an authorized user. A system's FRR is
typically stated as the ratio of the number of false rejections to the number of identification attempts.
fingerprint recognition -The automated process of matching two human fingerprints: one previously
recorded and one being provided by a user for authentication. BioStar incorporates Suprema's award-
winning algorithms for recognizing fingerprints.
fingerprint sensor: A fingerprint sensor is an electronic device used to capture a digital image of the
fingerprint pattern. The captured image is called a live scan. This live scan is digitally processed to
create a biometric template (a collection of extracted features) which is stored and used for fingerprint
recognition.

Glossary
fire alarm zone: A zone that is used to interface with fire alarms and control doors when a fire is
detected.
host: A host is the device that serves as the master in a RS485 network. The host device relays data
packets between external devices (or a larger network) and slave devices connected to the RS485
network.
input signal: The signal sent to a device by an external object, such as an exit button.
operator: Operators are personnel who have rights to use BioStar clients. BioStar includes three pre-
defined classes for operators: administrators, operators, and managers. BioStar also supports a
maximum of 16 custom operator classes.
output signal: The signal sent to an external device, such as an alarm siren or electronic door strike.
proximity card: Proximity cards (or "prox" cards) are contactless integrated circuit devices used for
security access. BioStation, BioEntry Plus, and BioLite Net devices support EM4100 cards; BioStation
Mifare, BioEntry Plus Mifare, BioEntry W Mifare and BioLite Net, and DStation devices support MIFARE
and iCLASS cards; and BioStation HID and BioEntry Plus HID devices support HID proximity cards.
RF device: Short-range radio frequency devices used to gain access to doors. The BioStar system
allows 3rd party RF devices to be added to the system to incorporate existing hardware into the access
control configuration
security level: see: false acceptance rate.
time and attendance (T&A): This designation refers to the processes and functions that monitor and
report check-in and check-out activities by employees and allow administrators to define time slots
and schedules. The information collected by the BioStar system can be used in conjunction with
external systems for time reporting and payroll capabilities.
timed anti-passback: A security protocol that prevents reauthorization of a user for a specified period
of time. See also: anti-passback.
timezone: A customizable schedule that can be used to allow or restrict access during specified hours.
Timezones can combined with doors to create access groups.
user: A user is any person who has access rights. A user's access rights are comprised of individual
rights (user level), membership in access groups, and time restrictions.
Wiegand interface: The Wiegand interface is a wiring standard used to connect a card swipe
mechanism to the rest of an electronic entry system. The interface uses three wires, one of which is a
common ground and two of which are data transmission wires usually called DATA0 and DATA1, but
sometimes also labeled Data High and Data Low.
zone: A zone consists of two or more devices that are grouped together. BioStar includes seven types
of zone classifications.

Index
A
anti-passback zone
access cards Access Group tab, 236
issuing, 72 Alarm tab, 236
Details tab, 234
Access Control tab
B
BioEntry Plus, 147
BioEntry W, 147 BioEntry Plus
BioLite Net, 157 configuring, 40
BioStation, 136 overview, 11
BioStation T2, 209
BioEntry W
D-Station, 186
overview, 11
FaceStation, 223
Xpass, 166 BioLite Net
Xpass Slim, 175 configuring, 43
X-Station, 196 overview, 11
access groups BioMini

adding, 84 overview, 12
adding users, 84 BioMini Plus
assigning to users, 85 overview, 12
selecting, 66
BioStar Server
transferring to devices, 86
configuring, 23
access zone
BioStation
Details tab, 242
configuring, 38
administrative account connecting via wireless LAN, 39
adding, 32 overview, 10
changing level or password, 32
BioStation T2
alarm zone configuring, 48, 50
Access Group tab, 240
BioStation T2
Alarm tab, 240
overview, 10
Details tab, 239
Black list tab
alarms BioEntry Plus, 150
activation events, 138, 188, 198, 213, 226
BioEntry Plus W, 150
adding custom sounds, 96
BioStation, 139, 160
configuring actions, 63
D-Station, 189
configuring settings and sounds, 95
X-Station, 199
customizing actions, 95
deactivation events, 138, 188, 199, 213, 227 Black list tab
priority, 138, 188, 199, 213, 227 BioStation T2, 214
releasing, 115 C

Index
Camera tab customizing D-Station settings, 180

X-Station, 195 customizing FaceStation settings, 218
customizing Xpass settings, 164
Camera tab
D-Station, 184 customizing Xpass Slim settings, 173
customizing X-Station settings, 193
Camera tab DHCP, 36
BioStation T2, 208
downgrading, 129
Camera tab locking or unlocking, 116
FaceStation, 221 removing, 128
resetting locks, 117
card ID format, 145, 165, 173
setting automatic locking, 116
client list, 24 static IP, 36
Command Card tab upgrading firmware, 128
BioEntry Plus, 151
Display/Sound tab
BioEntry W, 151 BioLite Net, 160
Xpass, 170 BioStation T2, 214
Xpass Slim, 178 D-Station, 189
command cards FaceStation, 228
deleting all users, 119 X-Station, 199
deleting an individual user, 118
Display/Sound tab
enrolling users, 70 BioEntry Plus, 151
issuing, 42, 45 BioEntry W, 151
connection type, 35 BioStation, 140
D
Display/Sound tab
databases Xpass, 170
creating, 22
Display/Sound tab
mapping imported data, 122 Xpass Slim, 179
migrating from BioAdmin, 28
doors
Device pane, 40, 43, 44 adding, 55
devices Alarm tab, 233
adding, 35 associating with devices, 55
adding RF devices, 38 configuring, 56
adding slave devices, 37 creating door groups, 56
creating a direct connection, 36 Details tab, 232
creating a server connection, 36 opening and closing, 115
customizing BioEntry Plus settings, 143
Double Mode, 133, 182, 194, 205, 220
customizing BioEntry W settings, 143
customizing BioLite Net settings, 153 D-Station
configuring, 46
customizing BioStation settings, 131
overview, 11
customizing BioStation T2 settings, 203

Index
E changing template, 130

image quality, 134, 183
EM4100 cards, 73
registering, 69, 70
email notifications, 96 security level, 134, 183, 207, 221
entrance limit setting, 136, 186, 196, sensitivity, 134, 183, 207, 221
210, 211, 224 sensor placement, 68
server matching, 134, 146, 155, 184
entrance limit zone
Access Group tab, 238 fire alarm zone
Alarm tab, 238 Alarm tab, 241
Details tab, 237 Details tab, 241
H
event logs
viewing from the monitoring pane, 110, 111 HID proximity cards, 73
event views holiday schedules, 83
changing, 28
host device
events adding, 37
real-time monitoring, 105 I
uploading logs to BioStar, 109
iClass CSN cards, 75
viewing logs, 108
viewing logs in panes, 109 iClass layout
editing, 78
external devices
configuring inputs, 98 Input tab
configuring outputs, 97 BioEntry Plus, 148
F BioEntry W, 148
BioLite Net, 158
face image BioStation, 136
capture, 70
BioStation T2, 211
FaceStation D-Station, 187
overview, 11 FaceStation, 225
Xpass, 167
FeliCa cards, 72
Xpass Slim, 176
Fingerprint tab X-Station, 197
BioEntry Plus, 145
BioEntry W, 145 installation
BioStar Client, 25
BioLite Net, 155
BioStar Express, 19
BioStation, 133
BioStar server, 20
BioStation T2, 207
D-Station, 183 interlock zone
FaceStation, 221 Details tab, 244
fingerprints Interphone tab

activating encryption, 129 BioStation T2, 210

Index
FaceStation, 224 USB settings, 136

L O
Lift I/O operation mode

overview, 12 1 to 1, 132, 181, 193
1 to N, 133, 182
lifts
server matching, 165, 173, 194
adding, 57
adding users, 58 Operation mode tab
associating with devices, 57 X-Station, 193
configuring, 58
Operation Mode tab
setup, 57
BioEntry Plus, 144
logging in to BioStar, 26 BioEntry W, 144
M BioLite Net, 153
BioStation, 131
MIFARE CSN cards, 75
BioStation T2, 204
MIFARE layout D-Station, 181
editing, 77 FaceStation T2, 218
MIFARE template cards, 76 Xpass, 164
Xpass Slim, 173
monitoring, 105
Output tab
muster zone
BioEntry Plus, 149
Access Group tab, 243
BioEntry W, 149
Details tab, 243
BioLite Net, 159
roll call, 107
BioStation, 137
N
BioStation T2, 212
Network tab D-Station, 188
BioEntry Plus, 146 FaceStation, 226
BioEntry W, 146 Xpass, 169
BioLite Net, 156 Xpass Slim, 177
BioStation, 135 X-Station, 198
BioStation T2, 208 S
D-Station, 185
FaceStation, 222 Secure I/O
overview, 12
Xpass, 165
Xpass Slim, 174 Server Settings, 135, 185, 196, 209, 223
X-Station, 195
site keys
networking changing, 76
RS232 settings, 136, 186, 209, 223
support, 249
RS485 settings, 136, 186, 196, 209, 223
server settings, 135, 185, 196, 209, 223 system requirements, 18
T
TCP/IP settings, 135, 185, 196, 208, 209, 222

Index
T&A mode Details tab, 245

BioEntry Plus, 148 enrolling via command cards, 70
BioLite Net, 162 exporting data, 121
BioStation, 141 Face tab, 246, 247
D-Station, 191, 216, 229 Fingerprints tab, 246
Xpass, 167, 176 importing data, 122
X-Station, 202 modifying information fields, 121
registering fingerprints, 68
T&A tab
BioLite Net, 162 retrieving data from device, 80
BioStation, 141 synchronize all, 80
BioStation T2, 215 T&A tab, 248
D-Station, 191 transfer to device, 79
FaceStation, 229 transferring to other departments, 119
X-Station, 201 V
time and attendance visual map

adding a daily schedule, 88 creating, 112
adding a holiday rule, 93 monitoring doors, 113
adding a leave period, 94 W
adding a shift, 90 Wiegand format
adding a time category, 87 26-bit, 52
generating T&A reports, 124 custom, 53
modifying T&A reports, 125 pass-through, 53
monitoring T&A status via the IO Board, 123
Wiegand mode, 143, 192, 217, 231
overview, 17
printing or exporting T&A report data, 127 Wiegand tab
D-Station, 192
Timezone pane, 82
Wiegand tab
timezones BioEntry Plus, 152
adding holidays, 83
BioEntry W, 152
creating, 82
BioLite Net, 163
toolbar, 27 BioStation, 143
U Xpass, 172
Xpass Slim, 180
users
adding new information fields, 118, 119, 120 Wiegand tab
Card tab, 247 X-Station, 203
creating accounts, 66
Wiegand tab
customizing information fields, 119
BioStation T2, 217
deleting, 118
deleting all via command cards, 119 Wiegand tab
deleting an individual via command cards, FaceStation, 230
118 X

Index
Xpass zones
configuring, 44 adding, 61
overview, 11 adding devices, 61
bypassing restrictions, 66
Xpass Slim
configuring alarm actions, 63
overview, 11
configuring arm and disarm settings, 63
X-Station configuring external input/output settings,
configuring, 47 64
overview, 11 configuring inputs, 62
Z types, 60
viewing events, 66

Suprema Inc.
16F Parkview Office Tower, Jeongja, Bundang, Seongnam, Gyeonggi, 463-863 Korea
Tel: +82-31-783-4502 Fax: +82-31-783-4503
Email: [email protected] Homepage: www.supremainc.com

BioStar 1 8 Administrator Guide - EN PDF

Uploaded by

Copyright:

Available Formats

BioStar 1 8 Administrator Guide - EN PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BioStar 1 8 Administrator Guide - EN PDF

Uploaded by

Copyright:

Available Formats

f

Suprema Warranty Policy ................................................................................... vii

02 Install the BioStar Software .................................................. 19

03 Setup the BioStar System ..................................................... 35

Copyright 2014, Suprema Inc. On the web: www.supremainc.com ii

3.1.2 Add and Customize Administrative Accounts ......................................... 36

Copyright 2014, Suprema Inc. On the web: www.supremainc.com iii

3.7 Setup Timezones .............................................................................. 94

04 Manage the BioStar System .............................................. 121

Copyright 2014, Suprema Inc. On the web: www.supremainc.com iv

4.3.2 Monitor Doors on a Visual Map ........................................................... 129

05 Customize Settings ............................................................ 149

Copyright 2014, Suprema Inc. On the web: www.supremainc.com v

5.2 Customize Door Settings ................................................................ 262

06 Technical Support .............................................................. 281

Copyright 2014, Suprema Inc. On the web: www.supremainc.com vi

Warranty and Disclaimers

Suprema Warranty Policy

Copyright 2014, Suprema Inc. On the web: www.supremainc.com vii

Copyright 2014, Suprema Inc. On the web: www.supremainc.com viii

Standard Edition Free Version

Maximum # of doors 512 20

Zone support Yes No

Email notifications Yes No

Server matching Yes No

Shift types Daily and Weekly Weekly only

Visual Map Yes No

Copyright 2014, Suprema Inc. On the web: www.supremainc.com 9

1. About the BioStar System

BioStar V1.8 supports the following devices:

BioStation (V1.5 or later): BioStation is a multifunctional terminal with a

BioStation T2: BioStation T2 is a multifunctional, IP-based access control

D-Station: D-Station is a multifunctional, IP-based access control terminal

FaceStation: FaceStation is a multifunctional, IP-based access control

BioEntry Plus (V1.2 or later): BioEntry Plus is an IP-based access control

Copyright 2014, Suprema Inc. On the web: www.supremainc.com 10

1. About the BioStar System

BioLite Net (V1.0 or later): BioLite Net is IP-based fingerprint terminal

Xpass: Xpass is an IP-based access reader/controller designed exclusively for

X-Station: X-Station is an easy-to-use smart IP terminal with a 3.5-inch

Copyright 2014, Suprema Inc. On the web: www.supremainc.com 11

1. About the BioStar System

1.1 Logical Configuration

Copyright 2014, Suprema Inc. On the web: www.supremainc.com 12

1. About the BioStar System

BioStar is a server-client application that supports up to 32 clients (2 clients maximum in the

Copyright 2014, Suprema Inc. On the web: www.supremainc.com 13

1. About the BioStar System

1.2 Access Control Features

1.2.1 User Authentication

Copyright 2014, Suprema Inc. On the web: www.supremainc.com 14

1. About the BioStar System

[D-Station, X-Station, BioStation T2, and FaceStation]

Copyright 2014, Suprema Inc. On the web: www.supremainc.com 15

1. About the BioStar System

1.2.2 User Management

1.2.3 Access Group Management

1.2.4 Device Management

Copyright 2014, Suprema Inc. On the web: www.supremainc.com 16