0% found this document useful (0 votes)
88 views1 page

O Ooo: Instructions For Setting Id# Instructions For Left Loop Options

The document provides instructions for setting up a security system polling loop including: 1) The total current consumption of the entire polling loop cannot exceed 64mA. 2) Avoid assigning too many contacts to a single sensor loop to make it easier to identify faulty sensors. 3) Instructions are given for setting dip switches and jumpers to configure the left loop options including response time, current, and use of end of line resistors.

Uploaded by

llllllluis
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
88 views1 page

O Ooo: Instructions For Setting Id# Instructions For Left Loop Options

The document provides instructions for setting up a security system polling loop including: 1) The total current consumption of the entire polling loop cannot exceed 64mA. 2) Avoid assigning too many contacts to a single sensor loop to make it easier to identify faulty sensors. 3) Instructions are given for setting dip switches and jumpers to configure the left loop options including response time, current, and use of end of line resistors.

Uploaded by

llllllluis
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

Tne current consumption of the entire polling loop c anno t exceed 64 mA.

Complete the rksheet in this sect.Lon by describing e acn protection point


and entering the current drain alongside each device.

Although any number of sensoa may be assigned to a transponder loop,


avo Ld assigning too many contacts to any sensor loop (left o r- right) as
this ma k e s it difficult for the end u se r or your service personnel to
identify a specific sensor that has been faulted.
See Below for DIP Switch
Settings

See Below f or -
Jumper Options

1
4190 4190 4190
+-
+
RIGHT LOOP: FOR N.C. SERIES
POLLING LOOP CIRCUITS ONL Y. USE SEALED
(REEO) CONT ACTS.
ALWAYS OBSERVE POLARITY.
ALWAYS CONNECT IN PARALLEL, LEFT LOOP: FOR N.C. CIRCUIT
SEE TEXT FOR WIRE GAUGE ANO (INTERNAL EOLR) OR N.C.
WIRE LENGTH REQUIREMENTS, AND/OR N.O. CIRCUIT (EXTER-
NAL EOLR). (See Left Loop
Jumper Options Below.)

INSTRUCTIONS FOR SETTING ID# INSTRUCTIONS FOR LEFT LOOP OPTIONS


CONVERT ID NUMBER TO DIP SWITCH
SETTINGS ACCORDING TO THIS TABLE 1. RED JUMPER SETS LOOP
ON 1 2 3 4 5 6 7 8 RESPONSE TIME
OFF 1 o oo o o CUT= 10 MSEC

7
I (\ RED
UNCUT = 400 MSEC
OFF OFF OFF OFF
OFF OFF OFF ON
ON =
OFF =
1
2
2. WHITE JUMPER SETS CUR- r. WHITE
LEAVE THESE IN OFF
POSITION. (REO
OFF OFF OFF ON
OFF OFF ON OFF
ON =
OFF =
3
4
RENT ON LOOP
CUT = 0.1 mA FOR REED
r. BLUE
EXPOSEO AT OFF) OFF OFF ON OFF ON = 5
OFF OFF ON ON
OFF OFF ON ON
OFF =
ON =
6
7
CONTACTS
OFF ON OFF OFF OFF = 8 UNCUT = 1 mA FOR
OFF ON OFF OFF ON = 9 MECHANICAL SWITCHES
YOU ONLY NEED TO SET THE OFF ON OFF ON OFF= 10
LEFT LOOP#. OFF ON OFF ON ON = 11 3._ BLUE JUMPER - CUT ONLY
OFF ON ON OFF OFF= 12 WHEN AN EOLR IS NOT USED
OFF ON ON OFF ON = 13
OFF ON ON ON OFF= 14 NOTE: IF YOU USE HIGH CUR-
WHEN BOTH LOOPS ARE USED, OFF ON ON ON ON = 15
ON OFF OFF OFF OFF= 16 RENT FOR MECHANICAL
THE TRANSPONOER WILL ON OFF OFF OFF ON = 11
ON OFF OFF ON OFF= 18 SWITCHES YOU MUST
AUTOMATICALLY ADD (+1) TO ON OFF OFF ON ON = 19 USE AN EOLR (DO NOT
SET THE RIGHT LOOP #. ON OFF ON OFF OFF= 20
CUT BLUE bR WHITE
ON OFF ON OFF ON = 21
ON OFF ON ON OFF = 22 JUMPERS)
IF ONLY ONE LOOP IS USED, ON OFFON ON ON = 23
ON ON OFF OFF OFF = 24
USE THE LEFT LOOP, SET THE ID ON ON OFF OFF ON = 25
ON ON OFF ON OFF= 26
1t. ANO USE THE NEXT CONSEC- ON ON OFF ON ON = 27
U'11VE # FOR THE NEXT ON ON ON OFF OFF " 28
ON ON ON OFF ON = 29
TAANSPONDER.

You might also like