Scribd Logo
Upload

Welcome to Scribd!

  • 454 views

    2ch Mixer Eng

    Uploaded by

    george1
    This document provides circuit diagrams and part lists for a 2-channel stereo mixer with a microphone channel. Figure 1 shows the input circuits for the two stereo channels and microphone channel. It includes phono, line level inputs and controls for gain, balance and tone for each channel. Figure 2 shows how the channel signals are mixed and includes crossfader, master volume and headphone controls. Figure 3 is the power supply circuit. Figure 4 is the VU meter driver circuit. Specifications for inputs, controls and outputs are also provided. Block diagrams illustrate the signal flow through the mixer.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    2ch Mixer Eng

    Uploaded by

    george1
    454 views7 pages
    This document provides circuit diagrams and part lists for a 2-channel stereo mixer with a microphone channel. Figure 1 shows the input circuits for the two stereo channels and microphone channel. It includes phono, line level inputs and controls for gain, balance and tone for each channel. Figure 2 shows how the channel signals are mixed and includes crossfader, master volume and headphone controls. Figure 3 is the power supply circuit. Figure 4 is the VU meter driver circuit. Specifications for inputs, controls and outputs are also provided. Block diagrams illustrate the signal flow through the mixer.

    Original Description:

    2 channel mixer circuit

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides circuit diagrams and part lists for a 2-channel stereo mixer with a microphone channel. Figure 1 shows the input circuits for the two stereo channels and microphone channel. It includes phono, line level inputs and controls for gain, balance and tone for each channel. Figure 2 shows how the channel signals are mixed and includes crossfader, master volume and headphone controls. Figure 3 is the power supply circuit. Figure 4 is the VU meter driver circuit. Specifications for inputs, controls and outputs are also provided. Block diagrams illustrate the signal flow through the mixer.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    454 views7 pages

    2ch Mixer Eng

    Uploaded by

    george1
    This document provides circuit diagrams and part lists for a 2-channel stereo mixer with a microphone channel. Figure 1 shows the input circuits for the two stereo channels and microphone channel. It includes phono, line level inputs and controls for gain, balance and tone for each channel. Figure 2 shows how the channel signals are mixed and includes crossfader, master volume and headphone controls. Figure 3 is the power supply circuit. Figure 4 is the VU meter driver circuit. Specifications for inputs, controls and outputs are also provided. Block diagrams illustrate the signal flow through the mixer.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 7

    2Channel + Microphone Stereo Mixer

    A lot of friends me asked to draw a more shrunk circuit 2-ch mixer, which will contain also, operation CROSSFADER. The circuits can be modified and
    added also other channels, repeating basic that I give. It can are added channels stereo PHONO/line or even channels microphone with proportional
    modification of next stages. In the Fig.1 exist the input circuits of two channels and input of microphone channel. The two basic channels she is same
    between them. Thus that its go for a channel, the he is also go for the other. In each stereo channel exist two inputs, classic stereo input PHONO that is
    practical a correction filter RIAA and concerns the signal amplification of sound that emanates from the classic reproduction heads of classic disks LP.
    Exist also a stereo input of LINE high level for signals that emanate from CD players, Tuners, DVD, etc. The exits of this two stages are selected with
    switch S1 or S2 and they are applied in the next stage which is constituted from adder IC3. Here is regulated the BALANCE with the RV5 and GAIN with
    the RV1. In the next stage round the IC4 exist a classic 3-band regulation of tone circuit, the regulation of which becomes with the RV2-3-4. The exit of
    IC4 drive the RV6 that is at preference pontesometer [FADER]. By points 1-2-5-6 the signals connected to next stage [Fig.2]. In the Fig.1 exist also the
    microphone input, which is in electronic Balance connection, round the IC9A. Here exist the regulation of GAIN with the RV13. It follows a stage of tone
    two-band regulation, round the IC9B and a stage of parametric regulation of mid band with RV16 [Gain] and RV17 [Frequency Band]. With the RV19 we
    regulate VOLUME [FADER] and with the RV18 we regulate the BALANCE. By points 9-10-11 the signal is connected to the corresponding points that are
    found in the Fig. 2.
    Part List [Fig.1]
    R1-7-15-16-41-48-55-56=47 Kohms C1-13-37-45=150pF mylar-ceramic IC1-5-9-10= NE5532-LM833
    R2-8-42-49=150 ohms C2-3-15-16-20-21-27-28-38-39=47nF IC2-3-4-67-8= TL072
    R3-5-9-11-43-45-50-52=180 Kohms C4-5-9-11-42-44-47-48=18nF RV1-7= 22 Kohms Log. pot.*
    R4-6-10-12-44-46-51-53=15 Kohms C6-10-41-46=3.9nF RV2-3-8-9=2X100 Kohms Lin. pot.*
    R13-14-17-18-47-54-57-58-95=100 Kohms C7-12-43-49-82-83=5.6nF RV4-10=2X470 Kohms Lin. pot.*
    R19-22-59-62-98-100=4.7 Kohms C8-14-17-18-40-50-53-54-88=10uF 16V RV5-11-18=10 Kohms Lin. pot.*
    RV6-12=2X22 Kohms Log. pot. 45mm Slider
    R20-23-60-63-21-24-61-64=10 Kohms C19-30-55-66-89=22pF
    [FADER]
    R25-26-33-34-65-66-70-71=10 Kohms C22-31-58-67=47nF RV13=10 Kohms Log. pot.*
    R27-35-67-73-74-75-78-79-96=10 Kohms C23-32-59-68-25-34-61-70-85=4.7nF RV14-15-16=47 Kohms Lin. pot.*
    R28-29-36-37-68-69-76-77=3.3 Kohms C24-33-60-69=22nF RV17=2X100 Kohms Log.pot.*
    R30-31-38-39-70-71-78-79=1.8 Kohms C26-35-62-71=1.2nF RV19=10 Kohms Log. pot. 45mm Slider [FADER]
    R32-40-72-80=330 ohms C29-36-65-72-80-90=10uF 16V J1-2-5-6=4pin conn. 2.54mm pin step
    R81-83=2.2 Kohms C56-57-63-64=47nF J3-4-7-8-9-10=3pin conn. 2.54mm pin step
    R82-97=6.8 Kohms C73-74=1uF 100V MKT Jf1....8=RCA female Jack
    R84-88-93-94=22 Kohms C75-76=68pF ceramic or mylar JF9=3pin XLR male
    R85=100 ohms C77-78-86-87=47nF
    R86-87=2.7 Kohms C79=47uF 16V
    R89-90=5.6 Kohms C81=2.2nF *ALPS or PIHER type Potentiometer
    R91-92=3.9 Kohms C84=10nF All the Resistors is 1/4W 1% metal film
    R99-101=10 Kohms S1-2=2X2 0N/ON SW All the [nF] capacitors is 63-100v 5% MKT
    In the Fig.2 abut the various signals that emanate from the Fig.1. Switches S3-4-5 execute the operation of pre-Fader-listen [PFL] of proportional
    channels. If some switch functions then turns on corresponding diode led D4-5-6. Simultaneous turn-on the relay RL1 disconnect the program in the
    headphone and supply with the PFL signal. Round the IC14 exist the amplifier circuits of headphone drive. Round the IC12 exist the addition circuit of the
    signals from the two channels and the mic channel, as well the RV20 which function as CROSSFADER between the two stereo channels. The RV21 is
    final MASTER VOLUME [FADER] and adjust the final percentage of signal to the output. This role undertake the IC13 that has the leading possibility via
    the outputs Jf13-14 a power amplifier, simultaneously from the exits Jf11-12 we can take signal for recording.

    Part List [Fig.2]


    RV20=2X22 Kohms Log. pot. 45mm Slider
    R102-103-106-107-113-114=10 Kohms Q2-4=BD140
    [FADER]
    RV21=2X10 Kohms Log. pot. 45mm Slider
    R104-108-117-122-125-126=22 Kohms S3-4=3X2 PDT 0N/ON SW
    [FADER]
    R105-109=1 Mohms RV22=2X10 Kohms Log. pot.* S5=2X2 PDT ON/ON SW
    R110-111-112=1 Kohms C91-95-97-101-103-106-111-114=22pF RL1=12V Relay 2X2 SW
    R115-118-120-123-127=10 Kohms C92-93-98-99-104-105-109-110=47nF JF10=Jack female stereo 6.3mm
    R116-119-121-124-130=10 Kohms C94-96-100-102=10uF 16V JF11....14=RCA female Jack
    R128-131=27 Kohms C107-108-113-116=470uF 25V J11....14-17=3pin conn. 2.54mm pin ste
    R129-132-137-138-140-146=100 ohms C112-115=47uF 16V J16-17=4pin conn. 2.54mm pin step
    R133-135-139-145=100 Kohms IC11-12=TL072 RV20=2X47 Kohms Lin. Slider [FADER]*
    R134-136=47 ohms IC13-14=NE5532 - LM833 RV21=2X10 Kohms Log. Slider [FADER]*
    R141-147=10 ohms D1-2-3=1N4002
    R142-148=4.7 Kohms D4-5-6=LED 3 or 5mm RED *ALPS or PIHER type Potentiometer
    R143-149=820 ohms D7=1N4148 All the Resistors is 1/4W 1% metal film
    R144-150=47 Kohms Q1-3=BD139 All the [nF] capacitors is 63-100v 5% MKT
    In the Fig.3 exist a classic supply circuit and stabilization of various voltages that needs the various circuits of mixer as +/-15V for the Audio department
    and + 12V for the RL1 and VU meter supplying. The regulators IC18-19-20 good its they are placed on small heatsinks. Transformer T1 its placed in a
    separate box, far from the remainder circuit, so that is not created problem of influence of rests circuits, from noise, unless its toroidal. In the Fig.4 is found
    the indication circuit of level. This becomes with two classic circuits round the IC16-17 that drive the diodes Led D12..D31, that portrays the level in steps
    of 3dB. The IC15 functions as precision rectifier.

    Part List [Fig.3-4]


    R151-152-156-157=10 Kohms BR1= 80V/3A BRIDGE RECTIFIER IC20=7915 on Heatsink
    R153-154-155-158-159=1 Kohms D8-9-10-11=1N4148 T1=230V//2X15Vac >30VA
    R160=2.7 Kohms D12.......31-32=RED LED F1=500mA SLOW BLOW FUSE
    C117-118-124-125-127-128-130-131=100nF D33=12V 0.5W ZENER S6=2X2 ON-OFF SWITCH
    C119-121=1uF 25V IC15=TL072 J18=3pin conn. 3.96mm pin step
    C120=10uF 25V IC16-17=LM3516
    C122-123=4700uF 40V IC18=7812 on Heatsink All the Resistors is 1/4W 1% metal film
    C126-129-132=19uF 25V IC19=7815 on Heatsink All the [nF] capacitors is 63-100v 5% MKT
    SPECIFICATIONS
    PHONO INPUT [Unbalaced RCA]

    Sensitivity 2.5mV rms


    Impedance 47K//150pF
    LINE INPUT [Unbalaced RCA]
    Sensitivity 1V rms
    Impedance 47K
    Gain X1 until X3
    50HZ, 1KHZ, 10KHZ
    3-band EQ
    [18dB/oct]
    MIC INPUT [Balanced XLR]
    Sensitivity -56dB
    Impedance 2K
    Gain 36dB
    EQ. Section
    High 18db at 20KHZ
    Mid. Freq. 200HZ - 6KHZ
    Mid. Gain 15db
    Low 18db at 20HZ
    HEADPHONE OUT
    impedance 100 ohms min.

    FREQUENCY RESPONSE 20HZ-20KHZ -2dB

    DISTROTION T.H.D 0.01% A 1KHZ


    OUTPUT LEVEL +4db Typ.

    Block Diagram
    In the Fig.5 appears the block diagram of circuit, which it will help in the comprehension of logic of circuit.

    Sam Electronic Circuits 10/02


    [ Home ] [ My Database ]

    You might also like