Anodizing Presentation

ANODIZING
Small scale anodizing

In the home shop
Anodizing Benefits
Provides a hard surface
Approximately 80 on a Rockwell scale
Corrosion resistance
Variety of colors available
Repair over machined parts
Relatively thin finish compared to other options
L C D Anodizing Method
Low Current Density
Easily repeatable results in the home shop
Longer bath times than commercial methods
Weaker (safer) chemical concentrations
Less fumes
Equipment cost reduction
What is it?
The process itself is chemically complicated

But is extremely simple in actual practice
Most anodizing is more art form than science.

Industry methods are closely guarded
The process involves placing the part
To be anodized into a weak
Sulfuric acid electrolyte solution.
A low voltage current is then passed thru it.
Anodizing does not hide surface
Imperfections.
In most cases it greatly enhances any
imperfections.
Part preparation
CLEANLINESS is mandatory
Surface preparation defines final outcome
As machined parts will magnify any machining
marks left behind
Part must be clean and free of oils or other
surface contaminants
Part must pass water break test before
proceeding.
What happens in the tank?
The aluminum surface GROWS a layer of
aluminum oxide,which transforms into aluminum
hydroxide (anodize) and finally into hydroxide
monohydrate.
This layer is the equivalent to rust on steel.
It is non conductive.
(don't ask questions about this, I am no chemist. I

just know the process works)
Putting parts in the tank
Only aluminum or titanium should be in the tank
A strong electrical connection is required
As the part anodizes, this connection often fails as it is
stressed. Its the most common cause of anodizing failures.
Aluminum wire or rod works great.
It can be forced into threaded holes
Its possible to spot weld the wire in aplace not visible.
The spot where the connection is made will not be anodized
The wire used to hang the part will be anodized.
The LCD method uses a solution of 3 parts
Calculations
distilled water to one part sulfuric acid.
The current used is from 3 Amps square foot to 6
Amps a square foot.
The lower end of the amp range favors dyeing
quality and final color depth.
The upperend of the range favors surface
hardness.
The size of the pores is directly related to current
flow.
Larger pores are easier to dye,but to large and
the dye bleeds out during the finishing process.
Smaller pores makeforbetter surface hardness,
but can be hard to get the dye into.
Don't ask a lot of questions on the next slide!
I use an online calculator to do the math.
The link is provided.

http://ndhsubmersiblescience.com/ano/720rule.ht
ml The 720 rule
1 mil over 1 square foot will take 720 amp

minutes.
Rule of 720:
Minutes to anodize = (mils of coating desired
720) / Amps per ft2
The metric equivalent
Rule of 312:
Minutes to anodize = (microns of coating desired
3.12) / Amps per dm2
The parts are in the tank
What now?
Plan your next step
You have 90 minutes on average
Prepare the dye bath
Prepare the sealing bath
Have all this ready, it is imperative that the parts not
be allowed to dry out between steps from this point.
Out of the anodizing tank

You should notice a gold / bronze tint to the parts
If not,the anodizing most likely did not take
Immediately out of the tank rinse the parts
thoroughly in distilled water.
All the pores that have been created must be
flushed of acid solution.
Do not handle the parts! Anything that gets into the
pores will effect the final finish
Adding color
Commercial dyes are available
Rit brand dye works great in the homeshop
I have found the liquid dyes for synthetics give a more consistent finish
The parts can skip this process, if color is not needed.
Parts should still be on the racking devices used for the anodizing
Dye bath can last from a minute,to 30 minutes depending on color and finish
desired.
This is where more art form than science come in
The dye bath canbe heated, and aerated for more even finishes
The temperature must not exceed 140F
After the dye bath,the parts can be rinsed again.
I skip this step normally, and let the excess dye end up in thenext processing tank
Sealing the parts
Once dyed, the parts need sealed to keep out contaminants and keepthe dye in
the pores.
Boiling in water is the easiest and cheapest for the home shop.
Commercial nickel acetate sealants can be used at lower temps,and less sealing
time.
To prevent dye leaching out, the parts can be placed in steam for 10 to
15minutes,before being placed in the boiling water.
Time for a good seal is generally 30 minutes.
During the sealing the aluminum oxide pores are hydrated and grow shut
Commercial sealing, using nickel acetate. Full sealing occurs after 6 hours. The
part continues to harden on the surface after the process. Full hardness is
usually achieved by 30 days.
This can be sped up, by a 150f water rinse.

Anodizing Presentation

Uploaded by

Copyright:

Available Formats

Anodizing Presentation

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Anodizing Presentation

Uploaded by

Copyright:

Available Formats

ANODIZING

Small scale anodizing

The process itself is chemically complicated

Most anodizing is more art form than science.

(don't ask questions about this, I am no chemist. I

The link is provided.

1 mil over 1 square foot will take 720 amp

Out of the anodizing tank

You might also like