PC BASED APPLIANCES CONTROLLER
Submitted by:
INTRODUCTION
This project can be used for the controlling of various appliances using PC. It consist a
circuit for using the printer port of a PC, for control application using software and some
interface hardware. The interface circuit along with the given software can be used with
the printer port of any PC for controlling up to eight equipment. Parallel port is a simple
and inexpensive tool for building computer controlled devices and projects. The
simplicity and ease of programming makes parallel port popular.
SCOPE OF PROJECT
This project can be used in industries as well as in houses to control the various
appliances through PC. Devices can be controlled from the desktop while working on it.
DESRIPTION OF PROJECT
BASIC COMPONENTS REQUIRED
1. Personal Computer
2. Optocoupler
3. ULN 2803
4. Electro-mechanical Relay(SPDT)
5. Transformer(15v)
6. Voltage Regulator 78XX
7. Diode(IN4007), Resistors, capacitors
BRIEF INTRODUCTION TO PARALLEL
PORT
Hardware
The pin outs of DB25 connector is shown in the picture below:
The lines in DB25 connector are divided into three groups, they are:
1. Data lines (data bus)
2. Control lines
3. Status lines.
As the name refers, data is transferred over data lines. Control lines are used to control
the peripheral, and of course, the peripheral returns status signals back to the computer
through Status lines. These lines are connected to Data, Control and Status registers
internally.
Parallel port registers
The Data, Control and Status lines are connected to there corresponding registers inside
the computer. So, by manipulating these registers in program, one can easily read or write
to parallel port with programming languages like 'C' and BASIC.
The registers found in a standard parallel port are:
1. Data register
2. Status register
3. Control register
POWER SUPPLY
REGULATOR IC (78XX)
It is a three pin IC used as a voltage regulator. It converts unregulated DC current into
regulated DC current.
BRIDGE RECTIFIER
A bridge rectifier makes use of four diodes in a bridge arrangement to achieve full-wave
rectification. This is a widely used configuration, both with individual diodes wired as
shown and with single component bridges where the diode bridge is wired internally.
CIRCUIT DIAGRAM OF POWER SUPPLY
OPTOCOUPLER
There are many situations where signals and data need to be transferred from one
subsystem to another within a piece of electronics equipment, or from one piece of
equipment to another, without making a direct ohmic contact electrical connection. Often
this is because the source and destination are (or may be at times) at very different
voltage levels, like a microprocessor which is operating from 5V DC but being used to
control a triac which is switching 240V AC. In such situations the link between the two
must be an isolated one, to protect the microprocessor from over-voltage damage.
HIGH VOLTAGE HIGH CURRENT
DARLINGTON TRANSISTOR ARRAY
(ULN2803):
The eight NPN Darlington connected transistors in this family of arrays are ideally suited
for interfacing between low logic level digital circuitry (such as TTL, CMOS or
PMOS/NMOS) and the higher current/voltage requirements of lamps, relays, printer
hammers or other similar loads for a broad range of computer, industrial, and consumer
applications. All devices feature open–collector outputs and free wheeling clamp diodes
for transient suppression.
The ULN2803 is designed to be compatible with standard TTL families while the
ULN2804 is optimized for 6 to 15 volt high level CMOS or PMOS
ULN 2803
RELAY:
A relay is an electrical switch that opens and closes under the control of another
electrical circuit. In the original form, the switch is operated by an electromagnet to open
or close one or many sets of contacts. It was invented by Joseph Henry in 1835. Because
a relay is able to control an output circuit of higher power than the input circuit, it can be
considered to be, in a broad sense, a form of an electrical amplifier.
Here relay is used for the isolation of various heavy appliances to the PC. Since the PC
operates on very low current, but the current in various appliances is in Amperes
therefore isolation is necessary and relay is required. Here we have used single pole dual
through relay for the purpose.
CIRCUIT DIAGRAM OF PROJECT
CONCLUSION
The greatest learning experience in this project comes from the design and construction of
“PC Based Appliance Controller” which answer a lot of questions regarding the real
implementation of Embedded system, Electro-mechanical relays and Opto-couper, ULN
2803, Parallel Port of PC .
During the development of our project we studied and analyzed many real world applications
of Electronics and Software Engineering. Some of the theoretical knowledge that was
inculcated in us within our engineering program, which we have applied practically, are:
1. Use of voltage regulation and filtering in power supply.
2. Study of parallel ports.
3. Study of C-Language.
4. Study of ULN.
5. Understanding of single pole dual through relay.
6. Study of Optocoupler.
