DD Cen Iso TS 12780-2-2007

DRAFT FOR DEVELOPMENT DD CEN ISO/TS
12780-2:2007
Geometrical Product
Specifications (GPS)
Straightness
Part 2: Specification operators (ISO/TS
12780-2:2003)
ICS 17.040.01
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

Copyright European Committee for Standardization
Provided by IHS under license with CEN Licensee=FMC Technologies /5914950002
No reproduction or networking permitted without license from IHS Not for Resale, 08/30/2009 17:25:31 MDT
DD CEN ISO/TS 12780-2:2007
National foreword
This Draft for Development is the UK implementation of CEN ISO/TS

12780-2:2007. It is identical to ISO/TS 12780-2:2003.
This publication is not to be regarded as a British Standard.
It is being issued in the Draft for Development series of publications and
is of a provisional nature. It should be applied on this provisional basis,
so that information and experience of its practical application can be
obtained.
Comments arising from the use of this Draft for Development are
requested so that UK experience can be reported to the international
organization responsible for its conversion to an international standard.
A review of this publication will be initiated not later than 3 years after
its publication by the international organization so that a decision can be
taken on its status. Notification of the start of the review period will be
made in an announcement in the appropriate issue of Update Standards.
According to the replies received by the end of the review period,
the responsible BSI Committee will decide whether to support the
conversion into an international Standard, to extend the life of the
Technical Specification or to withdraw it. Comments should be sent to
the Secretary of the responsible BSI Technical Committee at British
Standards House, 389 Chiswick High Road, London W4 4AL.
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---
The UK participation in its preparation was entrusted to Technical

Committee TDW/4, Technical product realization (TPR).
A list of organizations represented on this committee can be obtained on
request to its secretary.
This publication does not purport to include all the necessary provisions
of a contract. Users are responsible for its correct application.
Compliance with a British Standard cannot confer immunity
from legal obligations.
This Draft for Development Amendments/corrigenda issued since publication

was published under the
authority of the Standards
Policy and Strategy Date Comments
Committee on 31 August
2008
BSI 2008
ISBN 978 0 580 57991 2

TECHNICAL SPECIFICATION CEN ISO/TS 12780-2
SPCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION December 2007
ICS 17.040.01
English Version
Geometrical product specifications (GPS) - Straightness - Part

2: Specification operators (ISO/TS 12780-2:2003)
Spcification gomtrique des produits (GPS) - Rectitude - Geometrische Produktspezifikation (GPS) - Geradheit - Teil
Partie 2: Oprateurs de spcification (ISO/TS 12780- 2: Spezifikationsoperatoren (ISO/TS 12780-2:2003)
2:2003)
This Technical Specification (CEN/TS) was approved by CEN on 8 October 2007 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMIT EUROPEN DE NORMALISATION
EUROPISCHES KOMITEE FR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 12780-2:2007: E
worldwide for CEN national Members.
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---

DD CEN ISO/TS 12780-2:2007
CEN ISO/TS 12780-2:2007(E)
Foreword
The text of ISO/TS 12780-2:2003 has been prepared by Technical Committee ISO/TC 213 "Dimensional and
geometrical product specifications and verification of the International Organization for Standardization (ISO)
and has been taken over as CEN ISO/TS 12780-2:2007 by Technical Committee CEN/TC 290 Dimensional
and geometrical product specification and verification the secretariat of which is held by AFNOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO/TS 12780-2:2003 has been approved by CEN as a CEN ISO/TS 12780-2:2007 without any
modification.
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---

3
DD CEN ISO/TS 12780-2:2007
ISO/TS 12780-2:2003(E)
Contents Page
Foreword ............................................................................................................................................................ iv
Introduction ........................................................................................................................................................ v
1 Scope...................................................................................................................................................... 1
2 Normative references ........................................................................................................................... 1
3 Terms and definitions........................................................................................................................... 1
4 Complete specification operator ......................................................................................................... 1
5 Compliance with specification ............................................................................................................ 3
Annex A (informative) Harmonic content of nominally straight workpiece ................................................. 4
Annex B (informative) Relation to the GPS matrix model .............................................................................. 6
Bibliography ....................................................................................................................................................... 8
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---
Copyright European Committee for Standardization ISO 2003 All rights reserved iii
DD CEN ISO/TS 12780-2:2007
ISO/TS 12780-2:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of normative document:
an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting
a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 12780-2 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.
ISO/TS 12780 consists of the following parts, under the general title Geometrical Product Specifications
(GPS) Straightness:
Part 1: Vocabulary and parameters of straightness
Part 2: Specification operators
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---
iv Committee for Standardization

Copyright European ISO 2003 All rights reserved
DD CEN ISO/TS 12780-2:2007
ISO/TS 12780-2:2003(E)
Introduction
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---
This part of ISO/TS 12780 is a geometrical product specification (GPS) Technical Specification and is to be
regarded as a general GPS standard (see ISO/TR 14638). It influences chain link 3 of the chain of standards
on form of line independent of datum.
For more detailed information on the relation of this part of ISO/TS 12780 to other standards and the GPS
matrix model, see Annex B.
This part of ISO/TS 12780 specifies the specification operators according to ISO/TS 17450-2 for straightness
of integral features.
At the current state of development, ISO/TC 213 has not been able to reach a consensus on defaults for filter
cut-off, probe tip radius and method of association (reference line). This means that a straightness
specification must explicitly state which values are to be used for these specification operations in order for it
to be unique.
Consequently, if a specification does not explicitly state which values are to be used for one or more of these
operators, the specification is uncertain (see ISO/TS 17450-2) and a supplier can use any value for the
operator(s) not specified when proving conformance.
Extracting data will always involve applying a certain filtering process. An additional filtering of the extracted
data may or may not be applied. This additional filter can be a mean line filter (Gaussian, spline, wavelet, etc.)
or a non-linear filter (e.g. morphological filter). The type of filtering will influence the definition of straightness
and the specification operators and, therefore, needs to be stated unambiguously.
NOTE 1 Stylus filtering is not sufficient on its own to smooth a profile. In certain circumstances it can create spurious
high-frequency content, thus giving incorrect values. To correct this, a longwave-pass filter is employed. A Gaussian filter
is used, since this is the current state-of-the-art in ISO standards. This filter has some shortcomings, e.g. it can distort,
rather than eliminate some roughness features and it can distort, rather than transmit correctly some waviness features. It
is envisioned that new filters under development within ISO will provide better solutions for several of these issues.
NOTE 2 If a smaller tip radius than the one specified is used for a given cut-off length, the resulting measured value will
generally be higher. This effect is usually insignificant. If a larger tip radius is used, the resulting measured value will
generally be lower. The amount of change is heavily dependent on the surface measured.
NOTE 3 The measuring force of 0 N is chosen to eliminate effects of elastic deformation of the workpiece from the
specification operator. On metal surfaces with adequate thickness, the effect of normally occurring measuring forces will
be negligible.
NOTE 4 Aliasing and other problems during extraction (see Annex A) due to the higher harmonic content of the skin
model, in the straightness directions, can cause specification uncertainty.
This part of ISO/TS 12780 is not intended to disallow any means of measuring straightness.
ISO 2003 All rights reserved

Copyright European Committee for Standardization v
DD CEN ISO/TS 12780-2:2007
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---

DD CEN ISO/TS 12780-2:2007
TECHNICAL SPECIFICATION ISO/TS 12780-2:2003(E)
Geometrical Product Specifications (GPS) Straightness
Part 2:
Specification operators
1 Scope
This part of ISO/TS 12780 specifies the complete specification operator for straightness of integral features
only and covers complete straightness profiles only, i.e. geometrical characteristics of features of type line.
NOTE Straightness of an extracted median line of a cylinder is defined in ISO/TS 12180-1 and ISO/TS 12180-2.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 11562:1996, Geometrical Product Specifications (GPS) Surface texture: Profile method Metrological
characteristics of phase correct filters
ISO/TS 12780-1:2003, Geometrical Product Specifications (GPS) Straightness Part 1: Vocabulary and
parameters of straightness
ISO 14253-1:1998, Geometrical Product Specifications (GPS Inspection by measurement of workpieces

and measuring equipment Part 1: Decision rules for proving conformance or non-conformance with
specifications
ISO/TS 17450-2:2002, Geometrical Product Specifications (GPS) General concepts Part 2: Basic tenets,
specifications operators and uncertainties
3 Terms and definitions

For the purposes of this part of ISO/TS 12780, the terms and definitions given in ISO/TS 12780-1 and
ISO/TS 17450-2 apply.
4 Complete specification operator
4.1 General
The complete specification operator (see ISO/TS 17450-2) is a full ordered set of unambiguous specification
operations in a well-defined order. The complete specification operator defines the transmission band for the
straightness profile, together with an appropriate stylus tip geometry.
1
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---

DD CEN ISO/TS 12780-2:2007
ISO/TS 12780-2:2003(E)
4.2 Transmission band
4.2.1 Longwave-pass filter
The longwave-pass filter shall be a phase correct filter (according to ISO 11562) transmitting waves of infinite
length and attenuating profile undulations progressively in the undulation region around the cut-off length (see
Figure 1).
Key
X wavelength, mm
Y transmission, %
NOTE Other filter values than those shown in Figure 1 can be used if necessary for the application.
Figure 1 Transmission characteristic for longwave-pass filter having

cut-off lengths c = 0,08 mm; 0,25 mm; 0,8 mm; 2,5 mm; 8 mm
The attenuation function is given by
2
c

a1
=e
a0
where
ln ( 2 )
= = 0,469 7

a0 = amplitude of sine wave undulation before filtering;
a1 = amplitude of this sine wave undulation after filtering;

--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---
c = cut-off length of the longwave-pass filter;
= wavelength of the sine wave.
2
Copyright European Committee for Standardization ISO 2003 All rights reserved
DD CEN ISO/TS 12780-2:2007
ISO/TS 12780-2:2003(E)
4.2.2 Cut-off wavelengths
The profile filter determines the range of periodic sinusoidal undulations of the feature included in the
straightness assessment. The range is terminated by values taken from Table 1. Table 1 also gives the
maximum sample point spacing to be used for the extracted line and the stylus tip radius needed to avoid
distortion of the straightness profile from the influence of the stylus tip.
Table 1 Cut-off values
Dimensions in millimetres
Longwave-pass filters
Filter transmitting from infinite Maximum stylus tip radiusa

Maximum sample point spacing
wavelength down to R
8 1,14 5
2,5 0,357 1,5
0,8 0,114 0,5
0,25 0,035 7 0,15
0,08 0,011 4 0,05
a When the maximum stylus tip radius requirement is fulfilled, the radius of the stylus tip is of comparable size to
the wavelength of the shortest undulations transmitted by the profile filter. This is consistent with the stylus tip radius
requirements for surface texture measuring instruments (see ISO 3274).
NOTE The required number of points corresponds to 7 sample points for each cut-off, which is the minimum number
of points to be assessed.
4.3 Probing system
4.3.1 Probing method
A contacting probing system with a stylus tip defined in 4.3.2 is part of the specification operator.
4.3.2 Stylus tip geometry
The theoretically exact stylus tip geometry is a sphere.
4.3.3 Probing force
The probing force is 0 N.
5 Compliance with specification

For proving conformance or non-conformance with specification, ISO 14253-1 applies.
3
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---

DD CEN ISO/TS 12780-2:2007
ISO/TS 12780-2:2003(E)
Annex A
(informative)
Harmonic content of nominally straight workpiece
A.1 Harmonic content

A finite length signal can be decomposed into a number of sinusoidal components called a Fourier series. A
Fourier series consists of a fundamental sinusoid whose wavelength is the length of the signal and harmonic
sinusoids whose wavelengths divide into the fundamental wavelength a whole number of times. The
fundamental sinusoid is called the first harmonic of the signal. The sinusoid whose wavelength is half the
fundamental wavelength is called the second harmonic. The sinusoid whose wavelength is one-third the
fundamental wavelength is called the third harmonic, etc. (see Figure A.1). Thus the nth harmonic is that
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---
sinusoid whose wavelength divides into the fundamental wavelength exactly n times. A straightness profile
can be decomposed into its harmonic components in this manner.
a) 1st harmonic
b) 2nd harmonic
c) 3rd harmonic
Figure A.1 First three harmonics of a signal
A.2 Aliasing and the Nyquist criterion

Recording digital data from a signal involves sampling that signal. The separation of the sampling points (the
sampling interval) must be chosen so that the digitized signal is representative of the original signal for the
method by which the signal will be analysed.
4
DD CEN ISO/TS 12780-2:2007
ISO/TS 12780-2:2003(E)
If the original signal is bandwidth limited, in that there is a shortest wavelength present (highest harmonic) in
the signal, then the Nyquist theorem imposes a limitation on the maximum sampling interval possible. The
Nyquist theorem states:
If it is known that an infinitely long signal contains no wavelengths shorter than a specified wavelength
then the signal can be reconstructed from the values of the signal at regularly spaced intervals provided
that the interval is smaller than half of the specified wavelength.
Strictly, the Nyquist theorem only applies to infinitely long signals. In practice, the Nyquist criterion of sampling
less than half of the shortest wavelength present is still useful even though signals are finite in length.
If a longer sampling interval than the Nyquist criterion is specified, the digitized signal will suffer from aliasing
distortion. Aliasing is when a short wavelength sinusoid appears to be a longer wave sinusoid due to the
sampling interval being too large to define the true shape of the signal (see Figure A.2). Thus, if too large a
sampling interval is chosen, the higher harmonics appear to be lower harmonics and distort any subsequent
analysis.
Key
A true signal
B alias signal
C sampling interval
NOTE The sampling interval is too large to define the true shape of the signal.
Figure A.2 Aliasing
In practice many measuring instruments impose an artificial band limitation on the signal to overcome the
problem of aliasing. There are many ways to achieve this artificial band limitation. Three common approaches
are using the natural band limitation of the probe, analog filters and digital filters or any combinations of
these. Usually it is a combination of all three. Once the signal has a band limitation, the Nyquist criterion can
be used to impose a theoretical maximum sampling interval as follows:
Assume all wavelengths less than the 0,02 % point of the Gaussian filter transmission curve can be
ignored, by applying the Nyquist theorem, means at least 7 sampling points per cut-off are required. This
represents the theoretical minimum number of sampling points per cut-off.
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,
Copyright European Committee for Standardization ISO 2003 All rights reserved 5
DD CEN ISO/TS 12780-2:2007
ISO/TS 12780-2:2003(E)
Annex B
(informative)
Relation to the GPS matrix model
For full details about the GPS matrix model, see ISO/TR 14638.
B.1 Information about this part of ISO/TS 12780 and its use
This part of ISO/TS 12780 specifies the complete specification operator for straightness i.e. geometrical
characteristics of features of type line.
B.2 Position in the GPS matrix model

This part of ISO/TS 12780 is a general GPS document, which influences chain link 3 of the chain of standards
on form of line independent of datum in the general GPS matrix, as graphically illustrated in Figure B.1.
Global GPS standards
General GPS standards
Chain link number 1 2 3 4 5 6

Size
Distance
Radius
Angle
Form of line independent of datum
Form of line dependent on datum
Fundamental Form of surface independent of datum
GPS
standards Form of surface dependent on datum
Orientation
Location
Circular run-out
Total run-out
Datums
Roughness profile
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---
Waviness profile
Primary profile
Surface imperfections
Edges
Figure B.1
6
DD CEN ISO/TS 12780-2:2007
ISO/TS 12780-2:2003(E)
B.3 Related International Standards

The related International Standards are those of the chains of standards indicated in Figure B.1.
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---

Copyright European Committee for Standardization 7
DD CEN ISO/TS 12780-2:2007
ISO/TS 12780-2:2003(E)
Bibliography
[1] ISO 3274:1996, Geometrical Product Specifications (GPS) Surface texture: Profile method
Nominal characteristics of contact (stylus) instruments
[2] ISO 4287:1997, Geometrical Product Specifications (GPS) Surface texture: Profile method
Terms, definitions and surface texture parameters
[3] ISO 4288:1996, Geometrical Product Specifications (GPS) Surface texture: Profile method Rules
and procedures for the measurement of surface texture
[4] ISO 10360-1:2000, Geometrical Product Specifications (GPS) Acceptance and reverification tests
for coordinate measuring machines (CMM) Part 1: Vocabulary
[5] ISO/TS 12180-1:2003, Geometrical Product Specifications (GPS) Cylindricity Part 1: Vocabulary
and parameters of cylindrical form
[6] ISO/TS 12180-2:2003, Geometrical Product Specifications (GPS) Cylindricity Part 2:

Specification operators
[7] ISO/TR 14638:1995, Geometrical Product Specifications (GPS) Masterplan
[8] ISO 14660-1:1999, Geometrical Product Specifications (GPS) Geometrical features Part 1:
General terms and definitions
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---
8
DD CEN ISO/TS 12780-2:2007
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---

DD CEN ISO/TS
12780-2:2007
BSI - British Standards Institution
BSI is the independent national body responsible for preparing British
Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of British
Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover. Tel:
+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996
7001 Email: [email protected] You may also buy directly using a debit/credit
card from the BSI Shop on the Website http://www.bsigroup.com/shop
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which
give details on all its products and services. Contact Information Centre. Tel:
+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: [email protected]
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration. Tel: +44 (0)20
8996 7002 Fax: +44 (0)20 8996 7001 Email: [email protected]
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsigroup.com/BSOL
Further information about BSI is available on the BSI website at http://
www.bsigroup.com.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may
be reproduced, stored in a retrieval system or transmitted in any form or by any
means electronic, photocopying, recording or otherwise without prior written
BSI Group permission from BSI.
Headquarters 389 This does not preclude the free use, in the course of implementing the standard,
Chiswick High Road, of necessary details such as symbols, and size, type or grade designations. If
London, W4 4AL, UK these details are to be used for any other purpose than implementation then the
Tel +44 (0)20 8996 9001 prior written permission of BSI must be obtained.
Fax +44 (0)20 8996 7001
www.bsigroup.com/ Details and advice can be obtained from the Copyright and Licensing Manager.
standards Tel: +44 (0)20 8996 7070 Email: [email protected]
--`,`,,,,,`,``,```,``,`,,,`,`,,`-`-`,,`,,`,`,,`---


DD Cen Iso TS 12780-2-2007

Uploaded by

Copyright:

Available Formats

DD Cen Iso TS 12780-2-2007

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DD Cen Iso TS 12780-2-2007

Uploaded by

Copyright:

Available Formats

What is the document about?

What is the document about?

What standards does it reference?

What standards does it reference?

DRAFT FOR DEVELOPMENT DD CEN ISO/TS

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

This Draft for Development is the UK implementation of CEN ISO/TS

The UK participation in its preparation was entrusted to Technical

This Draft for Development Amendments/corrigenda issued since publication

ISBN 978 0 580 57991 2

Copyright European Committee for Standardization

Geometrical product specifications (GPS) - Straightness - Part

EUROPEAN COMMITTEE FOR STANDARDIZATION

Management Centre: rue de Stassart, 36 B-1050 Brussels

Copyright European Committee for Standardization

Copyright European Committee for Standardization

Part 1: Vocabulary and parameters of straightness

Part 2: Specification operators

iv Committee for Standardization

ISO 2003 All rights reserved

Copyright European Committee for Standardization

Geometrical Product Specifications (GPS) Straightness

ISO 14253-1:1998, Geometrical Product Specifications (GPS Inspection by measurement of workpieces

3 Terms and definitions

4 Complete specification operator

ISO 2003 All rights reserved

4.2 Transmission band

4.2.1 Longwave-pass filter

Figure 1 Transmission characteristic for longwave-pass filter having

The attenuation function is given by

a0 = amplitude of sine wave undulation before filtering;

a1 = amplitude of this sine wave undulation after filtering;

c = cut-off length of the longwave-pass filter;

= wavelength of the sine wave.

4.2.2 Cut-off wavelengths

Table 1 Cut-off values

Filter transmitting from infinite Maximum stylus tip radiusa

4.3 Probing system

4.3.1 Probing method

4.3.2 Stylus tip geometry

The theoretically exact stylus tip geometry is a sphere.

4.3.3 Probing force

The probing force is 0 N.

5 Compliance with specification

ISO 2003 All rights reserved

Harmonic content of nominally straight workpiece

A.1 Harmonic content

Figure A.1 First three harmonics of a signal

A.2 Aliasing and the Nyquist criterion

Figure A.2 Aliasing

Relation to the GPS matrix model

B.2 Position in the GPS matrix model

Global GPS standards

General GPS standards

Chain link number 1 2 3 4 5 6

B.3 Related International Standards

ISO 2003 All rights reserved

[6] ISO/TS 12180-2:2003, Geometrical Product Specifications (GPS) Cylindricity Part 2:

[7] ISO/TR 14638:1995, Geometrical Product Specifications (GPS) Masterplan