Disclosure to Promote the Right To Information

Whereas the Parliament of India has set out to provide a practical regime of right to
information for citizens to secure access to information under the control of public authorities,
in order to promote transparency and accountability in the working of every public authority,
and whereas the attached publication of the Bureau of Indian Standards is of particular interest
to the public, particularly disadvantaged communities and those engaged in the pursuit of
education and knowledge, the attached public safety standard is made available to promote the
timely dissemination of this information in an accurate manner to the public.

1 +, 1 + 01 ' 5
Mazdoor Kisan Shakti Sangathan Jawaharlal Nehru
The Right to Information, The Right to Live Step Out From the Old to the New

IS 7002 (2005): Prevailing Torque Type Hexagon Nuts (With

Non-Metallic Insert), Style 1 - Property Classes 5,8 and 10
[PGD 31: Bolts, Nuts and Fasteners Accessories]

! $ ' +-
Satyanarayan Gangaram Pitroda
Invent a New India Using Knowledge

! > 0 B


BharthariNtiatakam
Knowledge is such a treasure which cannot be stolen
 r

IS 7002:2005
1s0 7040:1997

WURKIwwJ i& WtiJ fPTfM?i?

Indian Standard
PREVAILING TORQUE TYPE HEXAGON NUTS
(WITH NON-METALLIC INSERT),
STYLE 1 PROPERTY CLASS 5,8 ANDI0
(Second Revision )

ICS 21.060.20

G 61S 2005

BUREAU OF INDIAN STANDARDS

MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
August 2005 Price Group 2
Bolts, Nuts and Fasteners Accessories Sectional Committee, MGP 33

NATIONAL FOREWORD

This Indian Standard (Second Revision) which is identical with ISO 7040:1997 Prevailing torque type
hexagon nuts (with non-metallic insert), style 1 Property class 5, 8 and 10 issued by the International
Organization for Standardization (ISO) was adopted by the Bureau of Indian Standards on the
recommendations of the Bolts, Nuts and Fasteners Accessories Sectional Committee and approval of the
Medical Instruments, General and Production Engineering Division Council.

The original version of this standard was published in 1972 revised in 1991. The earlier edition was based
on ISO 7040:1983. This second revision has been harmonized with ISO 7040:1997 by adoption to make
pace with the latest developments taken place at international level.

The text of ISO Standard has been approved as suitable for publication as an Indian Standard without
deviations. Certain terminology and conventions are, however, not identical to those used in Indian
Standards. Attention is drawn especially to the following:

a) Wherever the words International Standard appear, referring to this standard, they should be
read as Indian Standard.
.

b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice
is to use a point (.) as the decimal marker.

In this adopted standard, reference appears to certain International Standards for which hcfian Standards
also exist. The corresponding Indian Standards, which are to bq substitded in .Wir plaoes, m listed
below along with their degree of equivalence for the editions indicated:

Inter flational Standard Corresponding Indian Standaizf . DegnM of Equivalence

ISO 225:1983 Fasteners Bolts, IS 8536 : 1987 Fasteners Bolts, Identical

screws, studs and nuts Symbols screws, studs and nuts Svmbols
and designations of dimensions and designation of dimension~ (first
revision)

ISO 261: 19731) ISO general purpose IS 4218 (Part 2) :2001 ISO geqeral Technically
metric screw threads General plan purposes metric screws threads : equivalent
Part 2 General plan (second revision)

ISO 965-2: 1980) ISO general purpose IS 14962 (Part 2) :2001 ISO general do
metric screw threads Tolerances purpose metric screw threads
Part 2: Limits of sizes for general Tolerances: Part 2 Limits of sizes for
purpose bolt and nut threads general purpose external and internal
Medium quality screw threads Medium quality

II Since revised in 1998.

(Continued on third cover)

 IS 7002:2005
1s0 7040: 1997

Indkm standard
PREVAILING TORQUE TYPE HEXAGON NUTS
(WITH NON-METALLIC INSERT),
STYLE 1 PROPERTY CLASS 5,8 AND 10
(Second Revision )
1 scope

This International Standard specifies the characteristics of prevailing torque type hexagon nuts (with
non-metallic insert), style 1, with threads from M3 up to and including M36, in product grade A for tkireadsup
to and including M16 and product grade B for threads above M 16, and with property classes 5,8 and 10.

NOTE The dimensions of the nuts correspond to those given in ISO 4032 plus prevailing torque feature.

If other specifications are required, they should be selected from existing International Standards, for example
ISO 261, ISO 965-2, ISO 2320 and ISO 4759-1.

2 Normative references

The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO
maintain registers of currently valid International Standards.

ISO 225:1983, Fasteners - Bolts, screws, studs and nuts Symbols and designations of dimensions

ISO 261:-, ISO general purpose metric screw threads - Genera\ plan.

ISO 965-2:-2, ISO general purpose metric screw threads - Tolerances - Part 2: Limits of sizes for general
purpose bolt and nut threads - /bledium quality.

ISO 2320:1997, Prevailing torque type steel hexagon nuts - Mechanical and performance propeflies.

ISO 3269:1988, Fasteners - Acceptance inspection.

ISO 4042:-3, Fasteners - Electroplated coatings.

ISO 4759-1 :, Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts Product grades A, B and C.

ISO 6157-2:1995, Fasteners - Surface discontinuities - Part 2: Nuts.

ISO 8992:1986, Fasteners - General requirements for bolts, screws, studs and nuts.

1) TO be published. (Revision of ISO 261:1973)

2) TO be published. (Revision of ISO 965-2: 1980)
3) To be published. (Revision of ISO 4042:1989)
4) To be published. (Revision of ISO 4759-1:1978)
IS 7002:2005
1s0 7040:1997

3 Dimensions

See figure 1 and table 1.

Symbols and designations of dimensions are specified in ISO 225.

.+.
@
mW
/32)

m
&

L--J--J

1) Prevailing torque element,

shape optional
2) p=15to 30

3) @= 90 to 120

Figure 1

Table 1 Dimensions
Dimension in mil netre

lhread (d) M3 M4 M5 M6 ME M1O Ml 2 (M14) M16 M20 M24 M30 M36

P 2 0,5 0,7 0,8 1 1,25 1,5 1,75 2 2 2,5 3 3,5 4

da max. 3,45 4,6 5,75 6,75 8,75 10,8 13 15,1 17,3 21,6 25,9 32,4 38,9

min. 3,00 4,0 5,00 6,00 8,00 10,0 12 14,0 16,0 20,0 24,0 30,0 36,0
.
dw min. 4,57 5,88 6,88 8,88 11,63 14,63 16,63 19,64 22,49 27,7 33,25 42,75 51,11

e min. 6,01 7,66 6,79 11,05 14,38 17,77 20,03 23,36 26,75 32,95 39,55 50,85 60,79

h max. 4,5 6,00 6,80 8,00 9,50 11,9 14,9 17,0 19,1 22,8 27,1 32,6 38,9

min. 4,02 5,52 6,22 7,42 8,92 11,2 14,2 15,9 17,8 20,7 25,0 30,1 36,4

m min. 2,15 2,9 4,4 4,9 6,44 8,04 10,37 12,1 14,1 16,9 20,2 24,3 29,4

%/4 min. 1,72 2,32 3,52 3,92 5,15 6,43 8,3 9,68 11,28 13,52 16,16 19,44 23,52

.T max. 5,50 7,00 8,00 10,00 13,00 16,00 18,00 21,00 24,00 30,00 36 46 55,0

min. 5,32 6,78 7,78 9,78 12,73 15,73 17,73 20,67 23,67 29,16 35 45 53,8

1) The size in brackets should be avoided if possible.

2) P is the pitch of the thread.
3) Minimum thread height.
4) Minimum wrenching height.

2
 IS 7002:2005
1s0 7040:1997

4 Requirements andreference international Standards

See table 2.

Table 2 Requirements and reference lntemational Standards

I
flaterial Nut body Steel

Insert For example, polyamid

;eneral requirements International Standard ISO 8992

bread Tolerance 6H

International Standards ISO 261, ISO 965-2

vlechanical and Property class 5 8 10

]erforrnance properties
Style decisive for style 1 style 1 style 1
mechanical properties

International Standard ISO 2320

[olerances Product grade Ford SM16:A

Ford> M16:B

International Standard 1s0 4759-1

Finish As processed

Requirements for electroplated coatings are

covered in ISO 4042.

If different electroplating requirements are

desired or if requirements are needed for
other finishes, they should be negotiated
between customer and supplier.
$,3

Limits for surface discontinuities are

covered in ISO 6157-2.

Acceptability For acceptance procedure, see ISO 3269.

%
5 Designation

EXAMPLE
A prevailing torque type hexagon nut, style 1, with non-metallic insert, thread M12 and property class 8 is
designated as follows:

Prevailing torque type hexagon nut ISO 7040- M12 -8

IS 7002:2005
Iso 7040:1997
NATIONAL ANNEX A
(National Foreword)

A-1 PACKAGING
The packaging of Prevailing torque type hexagon nuts shall be done in accordance with
IS 1367 (Part 18) :1996 Industrial fasteners Threaded steel fasteners Technical supply conditions:
Part 18 Packaging (third revision).

A-2 BIS CERTIFICATION MARKING

Details available with the Bureau of Indian Standards.

4
 F

(Continued from second cover)

International Standard Corresponding Indian Standard Degree of Equivalence

ISO 2320:1997 Prevailing torque type IS 1367 (Part 8): 2002 Technical supply Identical
steel hexagon nuts Mechanical and conditions for threaded steel fasteners:
performance properties Part 8 Prevailing torque type steel
hexagon nuts Mechanical and
performance properties (third revision)

ISO 3269 : 1988) Fasteners IS 1367 (Part 17) :2005 Technical Technically
Acceptance inspection supply conditions for threaded steel equivalent
fasteners: Part 17 Inspection, sampling
and acceptance procedure (fourth
revision)
.

ISO 4042 : 19892) Threaded IS 1367 (Part 11) :2002 Technical do

components Electroplated coatings supply conditions for threaded steel
fasteners: Part 11 Electroplated
coatings (third revision)

ISO 4759-1 : 19781) Tolerances for IS 1367 (Paf12): 2002 Technical supply do
fasteners Part 1: Bolts, screws, conditions for threaded steel fasteners:
studs and nuts Product grades A, Pait 2 Product grades and tolerances
B and C (third revisior$

ISO 6157-2 : 1995 Fasteners IS 1367 (Part 10) :2002 Technical Identical
Surface discontinuities Part 2: Nuts supply conditions for threaded steel
fasteners: Part 10 Surface
discontinuities Nuts (third revision)

ISO 8992:1986 Fasteners General IS 1367 (Part 1): 2002 Technical supply do
requirements for bolts, screws, studs conditions for threaded steel fasteners:
and nuts Part 1 General requirement for bolts,
screws and studs (third revision)

As decided by the Committee additional requirements of packaging and BIS Certification Marking are
given in National Annex A. These additional requirements are part of this Standard.

For the purpose of deciding whether a particular requirement of this standard is complied with, the final
value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in
accordance with IS 2:1960 Rules for rounding off numerical values (revised). The number of significant
places retained in the rounded off value should be the same as that of the specified value in this standard.

I I) since revised in 2000.

4 Since revised in 1999.

fj
,,
Bureau of Indian Standards

BIS is a statutory institution established under the Bureau of /ndian Standards Act, 1986 to promote
harmonious development of the activities of standardization, marking and quality certification of goods
and attending to connected matters in the country.

Copyright

BIS has the copyright of all its publications. No part of these publications maybe reproduced in any form
without the prior permission in writing of BIS. This does not preclude the free use, in the course of
implementing the standard, of necessary details, such as symbols and sizes, type or grade designations.
Enquiries relating to copyright be addressed to the Director (Publications), BIS.

Review of indian Standards

Amendments are issued to standards as the need arises on the basis of comments. Standards are also
reviewed periodically; a standard along with amendments is reaffkmed when such review indicates that
no changes are needed; if the review indicates that changes are needed, it is taken up for revision.
Users of Indian Standards should ascertain that they are in possession of the latest amendments or
edition by referring to the latest issue of BIS Catalogue and Standards: Monthly Additions.

This Indian Standard has been developed from Doc: No. MGP/BP 33 (041 O).

Amendments Issued Since Publication

Amend No. Date of Issue Text Affected

BUREAU OF INDIAN STANDARDS

Headquarters :
\
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002 Telegrams: Manaksanstha
Telephones: 23230131,23233375,23239402 (Common to all offices)

/
Regional Offices : Telephone
,,
Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg 23237617
NEW DELHI 110002 /. { 23233841

Eastern : 1/14 C.I.T. Scheme Vll M, V. 1. P. Road, Kankurgachi 23378499,23378561

KOLKATA 700054 { 23378626,23379120
Northern : SCO 335-336, Sector 34-A, CHANDIGARH 160022 2603843
{ 2609285
Southern : C.I.T. Campus, IV Cross Road, CHENNAI 600113 22541216,22541442
{ 22542519,22542315
Western : Manakalaya, E9 MlDC, Marol, Andheri (East) ~283292 95,28327858
MUMBAI 400093 128327891,28327892

Branches : AHMEDABAD. BANGALORE. BHOPAL. BHUBANESHWAR. COIMBATORE. FARID,ABAD.

GHAZIABAD. GUWAHATI. HYDERABAD. JAIPUR. KANPUR. LUCKNOW. NAdPUR. I
NALAGARH. PATNA. PUNE. RAJKOT. THIRUVANANTHAPU RAM. VISAKHAPATNAM.

Printed at Prebhat Offset Press, New Delhi-2