Tachogenerators

Solid shaft with EURO flange B10

With own bearings

TDP 0,2, TDPZ 0,2

Features
Low response time
Open circuit voltage 10150mV per rpm
Redundant output (TDPZ)
EURO-flange B10 / solid shaft 11 mm
Very high resistance to shock
High signal quality due to patented LongLife
technology
Recognition of sense of rotation possible via control

Optional
Marine air protected/tropicalized
TDP 0,2 Second shaft end (B14) / Housing foot (B3)

Technical data - electrical ratings Technical data - mechanical design

Reversal tolerance 0.1% Size (flange) 115 mm
Linearity tolerance 0.15% Shaft type 11mm solid shaft
Temperature coefficient 0.05%/K (open-circuit) 7mm solid shaft (optional)
14mm solid shaft (optional)
Isolation class B
Flange EURO flange B10
Calibration tolerance 1%
Protection DINEN60529 IP55, IP56(option)
Climatic test Humid heat, constant
(IEC 60068-2-3, Ca) Operating speed 10000rpm
Interference immunity EN 61000-6-2 Torque 1.5Ncm
Emitted interference EN 61000-6-3 Shaft loading 60N axial
80N radial
TDP 0,2 Materials Housing: aluminium die-cast
Performance 12 W (speed 3000 rpm) Shaft: stainless steel
Armature-circuit <75s Operating temperature -30...+130C
time-constant Resistance DIN EN 60068-2-6
Open-circuit voltage 10...150 mV per rpm Vibration 10g, 10-2000 Hz

Subject to modification in technic and design. Errors and omissions excepted.

IEC 60068-2-27
TDPZ 0,2
Shock 300 g, 1 ms
Performance 2x 3 W (speed 3000 rpm)
Connection Terminal box
Armature-circuit <40s
time-constant TDP 0,2
Open-circuit voltage 20...100 mV per rpm Rotor moment of inertia 1.1kgcm
Weight approx. 2.4kg
TDPZ 0,2
Rotor moment of inertia 1.2kgcm
Weight approx. 2.9kg
4/12/2013

1 www.baumer.com/motion
 Tachogenerators
Solid shaft with EURO flange B10
With own bearings

TDP 0,2, TDPZ 0,2

Part number
Tachogenerator Twin tachogenerator

TDP0,2LT- TDPZ0,2LT-

Open-circuit voltage Open-circuit voltage

6 10 mV per rpm 7 20 mV per rpm
7 20 mV per rpm 5 40 mV per rpm
10 30 mV per rpm 4 60 mV per rpm
5 40 mV per rpm 3 100 mV per rpm
4 60 mV per rpm
3 100 mV per rpm
1 150 mV per rpm

Data according to type

Open-circuit Minimum load required depending Maximum Armature Armature

Type
voltage on speed range [rpm] operating speed resistance inductance
0-3000 0-6000 0-nmax
U0 RL RL RL nmax R A (20C) LA
[mV/rpm] [k] [k] [k] [rpm] [] [mH]
TDP0,2LT-6 10 0.1 0.3 0.9 10000 3 6
TDP0,2LT-7 20 0.3 1.2 3.3 10000 11 23
TDP0,2LT-10 30 0.7 2.7 7.5 10000 26 50
TDP0,2LT-5 40 1.2 5 13.5 10000 47 90
TDP0,2LT-4 60 2.7 11 30 10000 99 200
TDP0,2LT-3 100 7.5 30 30 6000 271 550
TDP0,2LT-1 150 16 --- 30 4000 630 1260
Twin tachogenerator with redundant output
(The data refer to each of the two tachogenerator outputs)
TDPZ0,2LT-7 20 1.2 4.8 14 10000 19 45
TDPZ0,2LT-5 40 4.8 20 54 10000 70 170
TDPZ0,2LT-4 60 11 44 120 10000 160 390
TDPZ0,2LT-3 100 30 120 --- 6000 445 1080
Superimposed ripple (for RC = 0.7 ms): 0.5% (peak-peak) 0.2% (rms)

Subject to modification in technic and design. Errors and omissions excepted.

Replacement switching diagram
Polarity for positive rotating direction: A1 (TDPZ: 1A1, 2A1): + (VDE)
A2 (TDPZ: 1A2, 2A2): - (VDE)
RA LA R U(n)
A1

U0 (n) U(n) RL C
-n n
Tachogenerator A2
LA RL
RC R C A -U(n) U(n) = U0(n) U0 (n) for R > R L >> R A
RL R A + RL
4/12/2013

2 www.baumer.com/motion
Tachogenerators
Solid shaft with EURO flange B10
With own bearings

TDP 0,2, TDPZ 0,2

Terminal assignment Accessories

View A - Connecting terminal TDP 0,2 Carbon brushes
Polarity for positive direction of rotation Mounting accessories
K 35 Spring disk coupling
for solid shaft 6...12 mm
K 50 Spring disk coupling
A2
- K 60
for solid shaft 11...16 mm
Spring disk coupling
A1
+ for solid shaft 11...22 mm

View A - Connecting terminal TDPZ 0,2

Polarity for positive direction of rotation

- 2A2 1A2
-
+ 2A1
1A1
+

Subject to modification in technic and design. Errors and omissions excepted.

4/12/2013

3 www.baumer.com/motion
 Tachogenerators
Solid shaft with EURO flange B10
With own bearings

TDP 0,2, TDPZ 0,2

Dimensions

TDP 0,2 (TDPZ 0,2) - Version with Euro flange (B10)

d L1 L2
7 8.3 3
11 12.6 4
14 16.1 5

M20x1.5

TDPZ 0,2 TDP 0,2

M16x1.5
Positive rotating
direction

TDP 0,2 (TDPZ 0,2) - Version with housing foot (B3)

Positive rotating direction
M20x1.5
A
M16x1.5

TDPZ 0,2
TDP 0,2
d L1 L2
7 8.3 3

Subject to modification in technic and design. Errors and omissions excepted.

11 12.6 4
14 16.1 5 4/12/2013

4 www.baumer.com/motion