INTRODUCTION

A steel structure is an assemblage of a group of members expected to

sustain their share of applied forces and to transfer them safely to the
ground.
Depending on the orientation of the member in the structure and its
structural use, the member is subjected to forces either axial, bending or
torsion or a combination there of.
DESIGN OF STRUCTURAL ELEMENTS
The position of elements, namely beams, columns, trusses, purlins etc.
are marked on the plan provided by architects.
Various combinations of possible loads are ascertained and the members
are proportional on the basis of selected deign method.
Standard specifications and codes
The bureau of Indian standards has published a number of codes,
standard and handbooks
1S Handbook No.1- Properties of structural steel rolled
sections
1S 875-1987- Code of practice for design loads for building and
structure.
1S800-2007-Code of practice for use of structural steel in general
construction.
Advantages of steel as a structural material
They can be erected at faster rate
It is a recyclable material
Properly maintained steel structure has long life.
Disadvantage of steel as a structural material
Fatigue of steel is one of the major drawbacks.
 At the places of stress concentration in the steel sections, under
certain conditions, the steel may lose its ductility.
Steel structures needs fire proof treatments treatment, which
increases the cost.

UNIT-1 BEAM TO BEAM FRAMED CONNECTION

Two secondary beams ISLB-300@ 37.7kg/m and ISMB-500 are

connected to main beam ISMB-600

The size of cleat angle ISA 90*90*8mm provided

3- #20 bolts for angle and ISLB-300
4- # 20 bolts for angle and ISLB-300
3 # 20 bolts per cleat angle for main beam connection.
Use pitch= 60mm, edge distance=35mm
Soln:
ISLB-300 h=300, b=150, tf=9.4,tw=0.7mm,g1=60mm
ISLB-500 h=500, b=180, tf=17.2,tw=10.2 mm,g1=75mm
ISLB-600 h=600, b=210 tf=20.8,tw=12.0mm
Angle leg- 90mm
c=50mm
page 168 sp-6(hand book)
Beam to column framed connection
A beam ISMB-400 @ 61.6kg/m is connected to flange of a column
ISHB-400 @ 82,2kg/m using framed bolted connection size of cleat
angle ISA 150*115*12mm
6- # 20mm bolt in two rows is used to connect angle and beam.
3- # 20mm bolt for each angle to connect angle and column flange.
Use pitch=60mm, edge distance=35mm
Soln:
ISBH-400 h=400, b=250, tf=12.7,tw=10.6mm
ISBH-400 h=400, b=140, tf=16.0,tw=8.9mm,g1=70mm
BEAM TO COLUMN UNSTIFFENED SEAT CONNECTION
Column [email protected]/m
Beam- [email protected]/m
Seat angle- ISA 150*115*15mm
Cleat angle- 90*90*8mm
4# 22mm bolts for seat angle with column web
2# 20mm for remaining connections.
Soln:
ISHB-400 h=400, b=250, tf=12.7,tw=10.6mm
ISMB-400 h=400, b=140, tf=16.0,tw=8.9mm
Angle 150mm leg- a
115mm leg-c
90mm leg-c

Beam to column stiffened seat connection

Column [email protected]/m
Beam- [email protected]/m
Seat angle- ISA 100*100*10mm
Cleat angle- 90*90*8mm
Pair of stiffener: 2 ISA 90*90*8mm-500mm length.
8 # 20mm botts for stiffener to column in two rows.
2 # 20mm for remaining connection.
Framed connection
Beam ISMB-400 61.6kg/m, column [email protected]/m, plate- 50mm
width, 200mm depth and 12mm thick
b. Cross beam [email protected]/m
Main beam [email protected]/m
Plate-50mm width, 200mm depth and 10mm thick
a. Beam to column connection

b. Beam to beam connection

Beam-column shiftened seat connection:
Beam ISMB-400 @61.6 is connected to web of a column ISHB
[email protected] kg/m using stiffened seat connection.
Seat connection-180mm*150mm*16mm
Stiffened plate-180mm width,250mm depth and 10mm thick.
Cleat angle- ISA 80*80*8mm

Beam-column unstiffened seat connection

Beam [email protected]/m is connected to column ISHB-300@
58.8kg/m using seat angle ISA 150*150*15.
Provide seat angle ISA 80*80*8m.
Use 12mm fillet held for main connection.
Beam is connected to flange of a column.
 UNIT-2, UNIT-3
Part A: 1. Column with lacing
2. Battens
3. Column splices
4. Column gussetted base
5. Connection ( batted and welded)
(a) Beam to beam and beam to column
(b) Beam to column unstiffened seat connection
( c) Beam to column stiffened seat connection

Part B: Design and drawing

1. welded plate girder
2. bolted plate girder
3. Gantry plate girder
4. Roof truss ( welded and bolted)

Rolled steel section:

a. Rolled steel angles

b. Rolled steel channel section

C. Rolled steel beams

Rolled steel tee section

A. Column with single lacing :
Build up column consists of 2ISMC-400@ 49.4kg/m back to back with
a spacing 250mm
Lacing dimension-60mm*8mm
Inclination 45degree (w.r.t vertical)
Provide one # 20mm bolts at each end.

IMSC- [email protected]/m
h=400, b=100, tf=15.3, tw=8.6
Column with Double lacing :
Build up column consists of 2 ISHB-300@ 63kg/m spaced at 350mm c/c
Provide double lacing 60mm*10mm
Inclination of lacing-45degree
Provide 8mm size fillet weld for a length 50mm on either side.
Soln: ISHB- 300@63Kg/m
h=300, b=250, tf=10.6, tw=9.4

Beam to column framed connection

A beam ISMB-450 is connected to Flange of a column ISHB-

[email protected]/m by double angle framed connection.
The size of the angle is ISA 100*100*10
There are 3# 20 per angle to connect cleat angle with beam web
(pitch=6.5)
There are 3 # 20 per angle to connect cleat angle with column flange.
Soln: ISHB- 450
h=450, b=150, tf=17.4, tw=9.4,g=70
Soln: ISHB- 300
h=400, b=250, tf=12.7, tw=10.6
leg size=100 C=60mm

Beam to column un-stiffened seat connection

A secondary beam ISMB 400 @ 616N/m is connected to a flange of a
column.
ISMB 400 @ 872 N/m by using a unstiffened seat connection.
Cleat angle is an ISA 90*90*8mm and seat angle ISA 150*115*15mm.
1.2 # 20 is used to connect cleat angle with column flange and 2 # 20 is
used to connect seat angle with beam flange.
Beam to column stiffened seat connection
A secondary beam ISMB 400@ 616n/m is connected to the flange of the
column
ISHB 450@ 872n/m by using stiffened seat connection.
Cleat angle is ISA 90*90*8 mm and seat angle ISA 100*100*8mm.
Use 2# 20 for all these angle connection.
A pair of stiffener angle ISA 90*90*8mm and length 50cm
Stiffener angle are connected with two rows a # 20 rivts in each row.

Column bases
Slab base:
ISHB 400 @77.4 kg/cm2 is supported on slab base.
Size of the slab base 900mm*500mm*30mm
Size of the concrete base 1.5*1.5*1m
Size of the cleat angle ISA 150*115*10mm
Use 4- #24 di bolts between angle and column flange.
Provided 4 #20 dia anchor bolts.
Column with battens :
Build up columns consists of 2 ISMC 300 @ 35.8kg/m placed face to
face or toe 150m apart.
The column is connected to battens using welded connection size of the
battens = 250mm* 10mm spacing @ 700mm c/c.

Column with gusseted base

Column ISHB-400@ 82.2 with cover plates 320mm*16mm is supported
on gusseted base.
The size of the gussetled base-700mm*600mm*32mm
The thickness of gusselle plate-16mm
The cleat angle-ISA 150*75*12
 There are 12 #20 bolt arranged.
Two rows to connect pedestal 1m*1m*0.5m
4 # 16 anchor bolt are provided for connecting base plate with
concrete.

Column splices
1. Same column size: Column splice is provided for two columns
Ishb-250 @ 54.7 kg/m
a. Flange splice: 250mm*400*10mm
No of rivets 6 # 18 for each column on each side with pitch=
60mm and E.D= 40 mm
b. Web splice: 140mm*160*10mm
No of rivets 4 # 20 for each column

2. Differential column sizes :

Column ISHB-400 @ 77.4kg/m is supported an another column ISHB-
450 @ 87.2 kg/m
Provide suitable splices.
a. Depth of flange splices is 440mm and 10mm thickness.
b. Bearing plate of size 450mm*250mm*40 mm is provided in
between two columns
c. There are 6 # 20 rivets for each column on each side with
p=60mm and edge distance=40mm
UNIT -3 COLUMN BASE SUBJECTED TO MOMENT
Design a Slab base for a column ISHB-300@ 58.8 Kg/m to carry a load
of 600 KN and moment 10 KN.
Also design suitable pedestal and the welded connection. Take
compressive strength of concrete 20 N/mm2 and SBC of soil 200 KN/m2.

Solution: Given, P=600 KN & M=10 KN-m

Therefore, PU=900 KN & MU=15 KN-m

(a)Size of the plate :
For column ISHB- 300 @ 58.8 Kg/m
B=250 mm, h=300 mm
Provide plate width B=250+50mm projection on both sides

Therefore, B=350 mm

Length is calculated using

Bearing pressure,
 =364.2mm

Provide Slab Base

Hence with above dimensions, the Upward pressure

(C) Connection:Upward reaction on shaded area

Upward reaction on shaded area = ( avg upward pressure) (shaded area)

137200 N
Using 6 mm size fillet weld,

 Therefore, l = 175 mm

(d). Design of concrete base:

COLUMNS:
2). The top chord of a bridge truss having an effective length of 3.6m
has a c/s shown. Determine the compressive load this member can carry.
Properties of one channel
ISMC- 200 @ 22.1 Kg/m
area=
Ixx = 1819.3 * 104 mm4
Iyy = 140.4 * 104 mm4
Cyy =21.70 mm

Location of x-x axis :

y =132.24 mm
 [ ( ) ]

[ ( ) ]

IXX= 55.51 * 106

[ ( ) ] [ ]

 ( )

3) A built up column consist of 3-rolled steel I-beam ISWB-400 @ 66.7

kg/m and connected effectively to act as one column as shown. Take
le=4m. Determine safe load the column can carry.

soln :
[ ] [ ]

[ ( ) ] [ ]

UNIT-4 ROOF TRUSS
Points to remember:
Design totally 4 members(2-outer,2-inner)
Use equal angles
Minimum size of angle- ISA 50mmX5OmmX6mm
For outer members Double angles
Inner members Single angle
Take effective length le=0.85l
Provide a minimum of 2 bolts
Gusset plate thickness is same as angle thickness or more and it is
uniform throughout.

1) Line diagram of a roof truss with external load and forces in each
member along with nature are shown in fig. below. Design various
members of the roof truss along with their end connections with
gusset plate[welded or bolted].
Also design the supports consisting of angles and bearing plate for the
support reaction.
Also design anchor bolts for an uplift of 15KN at each support. Take
M20 concrete for the column. The right support may be considered as
anchoring with sliding provision.
The left support may be considered as only anchoring support.
Draw to a suitable scale
i)Elevation of truss greater than half span
ii)Enlarged view of apex joint of the truss
iii)Enlarged view of the left support joint.

A) Design of top chord member

{AB,BC & CD Members}

Taking maxium force = 240 KN(compression)

Factored force= 360 KN
Max length = 2.31m = l
Effective length le=0.85l=1.964m

a) Assume fcd=120N/mm2
Area = force/fcd = 360X103/120 = 3000mm2 = 30cm2

From steel table try 2ISA 80X80X10mm

Area = 30.10cm2 = 3010mm2
xx = 2.41cm, yy = 3.73cm
min = 24.1mm
= le/ min = 81.3
From table 9(c) P-42 IS 800
Fcd = 134.05 N/mm2
Design compressive load = Pd = fcd.Area
Pd= (134.05)(3010)= 403.4x103N>360KN (Safe)

b) Connection
Using M20 , property class 5.6 Black Bolt
i) Shear strength
Vdsb = Vnsb/mb [fy/3] No shank
= 113.18KN

ii) Bearing strength

P = 2.5d = 2.5X20= 50mm
e = 1.7do = 1.7 X 22 = 37.4 = 40mm
kb = (e/3do)= 0.61, (p/3d0-0.25)=0.51
(fub/fu)=500/410=1.22, 1.0
Kb=0.51
Vdpb= Vnsb/mb[2.5kb.d.t.fu]
1/1.25[2.5x0.51x20x10x410]=83.64KN
Bolt value = 83.64KN
No. of bolts = Forcw/BV = 360X103/83.64X103 = 5

B) Design of bottom chord member

[Members AL,LK and KJ]

Max. force = 207.84KN

Factored = 311.76KN
L= 2.0 m
Le= 0.85l = 1.7m

a) For preliminary sizing

Tdn=

= 0.8 Assuming no. of bolts more than 4

311.76X103 = 0.8XAnx410/1.25
An = 1188.1mm2
Increase approximately by 30%
= 1.30X1188.1= 1544.5mm2 = 15.44cm2

From steel tables try 2ISA 80X80X6mm

Area = 18.58cm2 = 1858mm2

b) Connection
Let us try M20 P Class 8.8 HSFG Bolts
Vdsf= Vnsf/ mf = 1/ mf [f.nekhFo]]

mf = 1.25, f=0.55, ne = 2
Kh= 1.0
FO = Ahb.fo = Ahb(0.7fub)

= 0.78 (0.7fub)

= 137.2X103
Vdsf = 1/1.25[(0.55)(2)(1)(13702x103)]
= 120.75KN
No.of bolts = 311.76/120.75 = 3

c) Check for rupture

w=80mm, t=6mm, bs=w+w1-t
bs=80+45-6= 119mm, Lc=100mm

= 1.4-0.076( ) )

= 0.665, Take min = 0.7

Ago= (B-t/2)t = (80 6/2)6 = 462

Anc = (A-do-t/2)t = (80-22-6/2)6 = 330

Tdn= 2[0.9 + ] = 334.4 KN > 311.76 KN (Safe)

d) Check for block shear

LV = 140mm, Lt = 35mm, t= 6mm

Avg = LV X t = 840
Avn = 840-2.5X22X6 = 510
Atg = Lt X t = 210
Atn = 210-0.5X22X6 = 144
Tdb = 305.46
Tdb = 269.00
Unsafe

Hence revise the angle section

Now try 2ISA 80x80X8mm, Area = 2442 mm2
Re check only Block shear
LV = 140 mm, Lt= 35mm, t = 8mm
Avg = Lt x t = 1120, Atg = Lt x t = 280
Avn = 1120-2.5X22X8 = 680 , Atn = 280-0.5X22X8 = 192
Tdb = 407.0 KN
Tdb = 359 KN > 311.76KN
Hence provide 2ISA 80X80X8mm with 3-M20 Bolts for bottom chord.

Design of Inner compression

[Member BK,CJ and DJ]

Max. compression = 66.05

Factored load = 99.07 KN
Max. length = l = 3.46m
Le = 0.85l = 2940mm

a) Assume fcd = 70N/mm2

Area = 99.07X103/70 = 1415.2 mm2 = 14.15cm2
From steel Tables Try single angle

ISA 80X80X10mm
Area = 1505 mm2
vv = 15.5 mm

Loaded through one leg

Refer Page 48
Assume more than two bolts and hinged
K1=0.7, k2=0.6, k3=5

vv =

= 2.13

= = 0.09

e = = 1.86

From Page 34

For buckling class c , = 0.49

= 0.5[1+(e-0.2)+e2] = 2.64

Fcd=
[ ]

= 50.35 N/mm2

Design compressive strength Pd = fcdXArea

Pd = (50.35)(1505) = 75.7X103 < 99.07KN (Unsafe)

Hence revise the section

Try ISA 100X100X10mm

Area= 1903mm2 ,VV = 19.4mm
vv = 1.70, = 0.112, e=1.58
= 2.08
Fcd= 66.20 N/mm2
Pd= FcdXArea= 66.20 X 1903 = 126KN> 99.07 (Safe)

b) Connection : Let us provide welded connection

Size of the weld

S=3/4 X Angle thickness
S = 3/4 X 10 = 7.5mm
Take s= 7mm
Force = strength of the weld

99.07 x 103 = 0.7 X S X l X

= (0.7 x 7)(l) [410/3 X 1.25]x 100

L1= 76.4mm
Provide l1= 80mm and l2 = 30mm
Hence provide ISA 100X100X10mm with welded connection.
C) Design of Inner tension members
Member CK
Force = 15 Kn
Factored = 22.5 KN
a) Since the force is very small, provide min. size of angle ISA
50X50X6mm
Area = 568mm2

b) Connection

Let us provide M16, P Class , 8.8 HSFG Bolts

UNIT- 4 GANTRY GIRDER

1) Design a simply supported gantry girder to carry an electricity
operation, travelling crane with the following data.
Span of crane bridge =25cm(c/c distance to gantry girder)
Column spacing =span of gantry girder=8m
Wheel base=3.5m
Crane capacity=200kn
Weight of crane bridge =150kn
Weight of trolley (crab)=75kn
Min. hook distance-1.0m
Weight of rail=0.30kn/m
Height of rail=105mm
SOLUTION:
a) Load calculation: maximum reaction in the crane bridge occurs,
when the trolley along with hook if it is towards left or right with a
minimum hook distance 1m.

MA=0, RA*25-150*12.5-275*24=0
RA=339kn
There are two wheels at each end of crane bridge .
Therefore load on each wheel = 12.5*169.5=211.87kn
Take 212kn
b) Now consider gantry girder:

The arrangement of wheel load for maximum BM is, the mid span is
equi-distance from resultant of two wheel loads and any one load.
ROLLING LOAD METHOD

later take moment under the wheel load 4 which is very close to mid
span.

md=0, rc*8-212*1.375-212(1.375+1.75+1.75)=0
RC=165.63kn
Therefore Mmax=RC*3.125=165.63*3.125=517.6kn
Therefore factored moment M=776.4kn-m

MAXIMUM SHEAR FORCE:

The arrangement of wheel load for maximum SF is two wheel loads is
placed either complete left or right side of the span.
MD=0
(RC*8)-(212*4.5)-(212*8)=0
Therefore Vmax=RC=331.25KN

c) Horizontal load and its moment.

A lateral load is developed due to the application of brakes or the sudden
acceleration of the trolley.
It is taken 10% of lifted weight and trolley weight.
Therefore Horizontal force = ((10/100)*(200+75))/4 wheels
=6.875KN
Therefore factored force=10.5KN
Therefore moment due to horizontal load = (776.4/212*1.5)*10.5
=25.64KN-M

d) Trial section:
The trial section is selected based on deflection condition .
The permissible deflection for electricity operated crane (upto
50t=500KN)
But actual deflection

)load+) self wt=10.67mm , E=2*10^5 N/mm*mm

using moment area method )load= (Area)x/EI2
= 10.67mm
IZ = 1.765X109 mm4
Increase the above value by 30% to 50% approximately
= 1.30 X 1.765 X 109 = 2.295 X 109 mm4
IZ =IX = 229500cm4
From steel table try suitable section
Try ISMB- 500 @ 95.2kg/m
ISMB- 400 @ 49.4kg/m
Top cover plate 320X20mm
Bottom cover plate 320X40mm
 Overall properties (P-36 steel
table)
IXX=IZZ= 230194.5X104mm4
Area = 376.15X100mm2
Cxx= 283.7mm (from top) and exx= 284.9mm(bottom)
r yy= 9.57cm= 95.7mm
(Page 6) ISMC-400 : Area= 6293mm2, Cyy = 24.2mm,tw=8.6mm
(Page 4)ISWB-500 : Area = 121.22X100mm2,
B= 250mm,tf=14.7mm
Location of equal area axis
Area of shaded portion = (Total area)
(9.9Xn)+(250X14.7)+(320X40)=1/2 [376.15X100]
n=235.61mm
Plastic modulus ZP=ay
= 9.05X106mm3
e) Check for moment of resistance:
For laterally unsupportedBeam
Design Bending strength= Md=BbZpfbd Page 54
E=2X105 N/mm2
LLT= 8m=8000mm (gantry girder span)
y=95.7mm for whole section.

Average or Mean Thickness of flange (P-63 steel table)

Top flange = 33.8mm = tf
Bottom flange= 51.5mm
Hf=c/c distance between flanges

Hf = overall depth-1/2 (Top and bottom mean thickness)

= 568.6-1/2(33.8+51.5)= 525.95mm

Fcrb= 1.1 [1+1/20( )]0.5

2
= 485.65 N/mm

From table 13a, P-55(IS-800)

Design bending compression stress=fbd=187.96N/mm2
Md=BdZpfcbd=1X9.05X106X187.96
Md=1701.3X106N-mm > (776.4 Kn-m moment + 25.64Kn-m)
Safe

f) Check for shear resistance

Design shear strength Vd=Vn/mo
AV=Shear area = hXtw for hot rolled
h=overall depth of the section
Av=568.6X9.9=5629.14
Vd=(5629.14)X250/(3)1/2X1.10
=738.63X103 N
>496.88 KN Safe
g) check for web crippling
Local capacity of the web = Fw(b1+n2)twfyw/mo
B1=100mm(assume)

H2=2.5[40+14.7] = 136.75mm

Fw=(100+136.75)x9.9x250/1.10
Fw=532.38KN > 496.88 KN(safe)
 h) Check for buckling of web
Buckling strength = (b1+n1)twXfcd
B1=100mm
H1=284.9mm=exx
Tw=9.9mm
=kL/ = le/min=0.7d/yy
= 3.44
From table 9(c) page 42
Fcd=227 N/mm2
Buckling strength = (100+284.9)X9.9X227
= 865X103N > 496.88KN (Safe)
Hence the above section can be used as a gantry girder.

Connection

The force at the junction = F=Vay/Iz N/mm2

F= 718.71N/mm
Equating the above force with strength of weld
718.71N/mm = 2[0.7XsX1X410/3X1.25]
S= 2.71mm
Provide min. 5mm weld , at top and bottom flange.

Design of bracket connection

a) No. of bolts = n =

l= No. of lines of bolts = 4

p= pitch= 2.5X20=50mm
R=bolt value = 60.38 KN
Moment M=PXe
P= Max. SF in GG= 496.88 Kn
Assume , e= 200mm
M= (496.88X103)(200)=99376X103 N-mm

n= = 8 per line

b) Check
i) Fa = P/N = 496.88X103/8X4
= 15.52KN
= = 190.39
2= 520X103 mm2
Fm= M/2 = 36.38KN

Resultant = R= cos
R= 44.82KN < Bolt value 60.38KN (Safe)