IC HDL Lab Manual

IC Applications and HDL Simulation Lab Manual
HOLY MARY INSTITUTE OF TECHNOLOGY & SCIENCE

(COLLEGE OF ENGINEERING)
Permanent affiliated to JNTU Hyderabad, Accredited by NAAC
Bogaram (v), Keesara (M), Ranga Reddy District.
IC APPLICATIONS & HDL SIMULATION LAB

LABORATORY STUDENTSMANUAL
For III year I semester ECE
A.Y.2015-16
DEPARTMENT
OF
ELECTRONICS & COMMUNICATION ENGINEERING
HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 1

VISION of Institute
To be a premier institute in the country and region for the study of engineering,
technology and management by maintaining high academic standards which promote
the analytical thinking and independent judgment among the prime stakeholders
enabling them to function responsibly in the globalized society.
MISSION of Institute
1. To impart quality professional education that meets the needs of present and
emerging technological world.
2. To strive for student achievement and success, preparing them for life and
leadership with ethics.
3. To provide a scholarly and vibrant learning environment that enables faculty,
staff and students achieve personal and professional growth.
4. To contribute to advancement of knowledge, in both fundamental and applied
areas of engineering, technology & management.
5. To undertake research and development works by forging alliances with
research institutes, government organizations, industries and alumni and
become a centre of excellence for quality professional educations and
research.
Vision of the Department
To be a world leader and renowned for Electronics & Communication Engineering

and research.
Mission of the Department
To educate graduates in the basic principles underlying the field of Electronics &
Communication Engineering and train our students to think independently in terms to
master systematic approach to problem solving and to have a keen awareness of the
role of engineering in the modern society.

LAB COURSE OUTCOMES:
CO1 Students will able to design circuits using

Linear ICs
CO2 Should able to simulate different
combinational and sequential circuits
using HDL

LAB INSTRUCTIONS
1. Do not handle any equipment without reading the instructions /Instruction

manuals.
2. Observe type of sockets of equipment power to avoid mechanical damage.
3. Do not insert connectors forcefully in the Sockets.
4. Strictly observe the instructions given by the Teacher/ Lab Instructor.
5. After the experiment is over, the students must hand over the Bread board, Trainer
kits, wires,CRO Probes and other Components to the lab assistant / teacher.
6. It is mandatory to come to lab in a formal dress (Shirts, Trousers, ID card, and
Shoes for boys). Strictly NO Jeans for both Girls and Boys
7. It is mandatory to come with observation book and lab record in which previous
experiment should be written in Record and the present labs experiment in
Observation book.
8. Observation book of the present lab experiment should be get corrected on the
same day and Record should be corrected on the next scheduled lab session.
9. Mobile Phones should be Switched OFF in the lab session.
10. Students have to come to lab in-time. Late comers are not allowed to enter the
lab.
11. Prepare for the viva questions. At the end of the experiment, the lab faculty will
ask the viva Questions and marks are allotted accordingly.
12. Bring all the required stationery like graph sheets, pencil & eraser, different color
pens etc. for the lab class.

List of Experiments
Experiment/ PAGE
NAME OF PROGRAM
week NO
1 OP AMP Applications Adder, Subtractor,Comparators
2 Integrator and Differentiator Circuits using IC 741.
3 Active Filter Applications LPF, HPF (first order)
4 IC 741 Waveform Generators - Sine, Squarewave and

Triangular waves.
5 IC 555 Timer - Monostable and AstableMultivibrator
Circuits.
6 Schmitt Trigger Circuits - Using IC 741
7 IC 565 - PLL Applications
8 Voltage Regulator using IC 723, Three Terminal Voltage

Regulators - 7805, 7809, 7912.
9 A) HDL code to realize all the logic gates
B) Design of 2-to-4 decoder

10 A) Design of 8-to-3 encoder (without and with Priority)
B) Design of 8-to-1 multiplexer and 1 x 8 demultiplexer.

11 A) Design of 4 bit binary to gray code converter
B) Design of 4 bit comparator

12 A) Design of Full adder using 3 modeling styles
B) Design of flip flops: SR, JK, T,D

13 Design of 4-bit binary,BCD counters
(synchronous/asynchronous reset)
14 Finite State Machine Design.
ADDITIONAL EXPERIMENTS
1 Wein Bridge Oscillator
2 RC Phase shift Oscillator

WEEK-1:
Experiment 1:
1. AIM: To study Adder, Subtractor& Comparator circuits using OP-AMP IC741
and verify theirtheoretical and practical output.
APPARATUS: Bread Board

IC741, Resistors
DC Supply
Function Generator
Multi meter
CRO
Probes, Connecting Wires
2. THEORY:
Adder: Op-amp can be used to design a circuit whose output is the sum of several
input signals. Such acircuit is called a summing amplifier or an adder. Summing
amplifier can be classified as inverting & non-inverting summer depending on the
input applied to inverting & non-inverting terminals respectively. Circuit Diagram
shows a non-inverting adder with n inputs. Here the output will be the linear
summation of input voltages. The circuit can be used either as summing amplifier,
scaling amplifier, or as averaging amplifier.
From the circuit of adder, it can be noted that at pin3
I1+I2+I3+.In=0
+ + + =0
=0
Va=
Vo Va
Vo ( )
Vo = (1+ )( )

(1+ (n-1))
) =n
Vo= V1+V2+V3++Vn
This means that the output voltage is equal to the sum of all the input voltages.
Subtractor: A subtractor is a circuit that gives the difference of the two inputs,
Vo=V2-V1, Where V1and V2 are the inputs. By connecting one input voltage V1 to
inverting terminal and another input voltage V2 to the non inverting terminal, we
get the resulting circuit as the Subtractor. This is also called as differential or
difference amplifier using op-amps.
Output of a differential amplifier (subtractor) is given as
Vo = (-Rf/R1) (V1-V2)
If all external resistors are equal in value, then the gain of the amplifier is equal to -1.
The output voltage of the differential amplifier with a gain of -1 is
Vo = (V2-V1)
Thus the output voltage Vo is equal to the voltage V2 applied to the non
inverting terminal minus the voltage V1 applied to the inverting terminal. Hence the
circuit is called a Subtractor.
Comparator: A Comparator is a non-linear signal processor. It is an open loop mode

application ofOp-amp operated in saturation mode. Comparator compares a signal
voltage at one input with a reference voltage at the other input. Here the Op-amp is
operated in open loop mode and hence the output is Vsat. It is basically classified as
inverting and non-inverting comparator. In a non-inverting
comparator Vin is given to +ve terminal and Vref to ve terminal. When Vin<Vref, the
output is Vsat and when Vin>Vref, the output is +Vsat (see expected waveforms). In an
inverting comparator input is given
to the inverting terminal and reference voltage is given to the non inverting terminal.
The output of the inverting comparator is the inverse of the output of non-inverting
comparator. The comparator can be used as a zero crossing detector, window
detector, time marker generator and phase meter.
3. CIRCUIT DIAGRAM:
Adder:

Subtractor:
Comparator:
4. PROCEDURE:
Adder:
1. Connect the components/equipment as shown in the circuit diagram.
2. Switch ON the power supply.
3. Apply dc voltages at each input terminal for V1 and V2 from the dc supply
and check the output voltage Vo at the output terminal.
4. Tabulate 3 different sets of readings by repeating the above step.
5. Compare practical Vo with the theoretical output voltage Vo =V1+V2.
Subtractor:

3. Apply dc voltages at each input terminal for V1 and V2 from the dc supply
and check the output voltage Vo at the output terminal.
4. Tabulate 3 different sets of readings by repeating the above step.
5. Compare practical Vo with the theoretical output voltage Vo =V2-V1.
Comparator:
3. Apply 1 KHz sine wave with 5 Vpp at the non-inverting input terminal of
IC741 using a function generator.
4. Apply 1V dc voltage as reference voltage at the inverting terminal of IC741.
5. Connect the channel-1 of CRO at the input terminals and channel-2 of CRO
at the output terminals.
6. Observe the input sinusoidal signal at channel-1 and the corresponding output
square wave at channel-2 of CRO. Note down their amplitude and time
period.
7. Overlap both the input and output waves and note down voltages at positions
on sine wave where the output changes its state. These voltages denote the
Reference voltage.
8. Plot the output square wave corresponding to the sine input with Vref = 1V.
5. TABLE:
Adder:
S.No. V1 V2 Theoretical Practical Vo
Volts Volts Vo=V1+V2 Volts
Subtractor:
S.No. V1 V2 Theoretical Practical Vo
Volts Volts Vo=V2-V1 Volts
Comparator:
Theoretical Reference
voltage (from circuit)
Practical Reference
voltage (from output
waveforms)

6. EXPECTED WAVEFORMS:
COMPARATOR INPUT & OUTPUT WAVEFORMS
7. RESULT:
8. VIVA QUESTIONS:
1. Draw the circuit diagram of 3 input adder.
2. What is the other name for adder?
3. Draw the circuit diagram of a Subtractor.
4. Which amplifier acts as a Subtractor?
5. How many basic input parameters are required for a comparator?
6. Draw the circuit diagram of a non-inverting comparator and inverting
comparator.
7. What is the output of a non-inverting comparator and inverting
comparator if the input is sinusoidal?
8. What are the differences between the Inverting and NonInverting
comparator?
9. What is the name of the comparator if the reference voltage is 0V?

10. Draw the circuit diagram and the output waveform of a Zero Crossing
Detector if the input is sinusoidal?
11. What is the name of a regenerative comparator?
12. Draw an op- amp circuit whose output Vo is V1+ V2 V3 V4.

WEEK-2:
EXPERIMENT NO: 2
1.AIM: To study the operation of the Integrator & differentiator using op-amp and
trace the output waveforms for sine and square wave inputs.
2.APPARATUS: Bread Board

IC741, Resistors, Capacitors
Function Generator
CRO
Probes
Connecting wires
3.THEORY:
Integrator:
A circuit in which the output voltage is the integration of the input voltage is
called an integrator.
In the practical integrator to reduce the error voltage at the output, a resistor
RF is connected across the feedback capacitor CF. Thus, R F limits the low-frequency
gain and hence minimizes the variations in the output voltage.
The frequency response of the integrator is shown in the fig. 2.1. fb is the
frequency at which the gain is 0 dB and is given by
fb = 1/2 R1Cf.
In this fig. there is some relative operating frequency, and for frequencies
from f to fa the gain RF/R1 is constant. However, after fa the gain decreases at a rate
of 20 dB/decade. In other words, between fa and fb the circuit of fig. 2.1 acts as an
integrator. The gain-limiting frequency fa is given by
fa = 1/2 RfCf.
Normally fa<fb. From the above equation, we can calculate Rf by assuming

fa& Cf. This is very important frequency. It tells us where the useful integration
range starts.
If fin<fa - circuit acts like a simple inverting amplifier and no integration results,
If fin = fa - integration takes place with only 50% accuracy results,
If fin = 10fa - integration takes place with 99% accuracy results.
In the circuit diagram of Integrator, the values are calculated by assuming fa

as 50 Hz. Hence the input frequency is to be taken as 500Hz to get 99% accuracy
results.
Integrator has wide applications in

1. Analog computers used for solving differential equations in simulation
arrangements.
2. A/D Converters
3. Signal wave shaping
4. Function Generators.
Differentiator:
As the name suggests, the circuit performs the mathematical operation of
differentiation, i.e. the output voltage is the derivative of the input voltage.
Both the stability and the high-frequency noise problems can be corrected by
the addition of two components: R1 and Cf, as shown in the circuit diagram. This
circuit is a practical differentiator.
The input signal will be differentiated properly if the time period T of the
input signal is larger than or equal to RfC1. That is, T>= RfC1
Differentiator can be designed by implementing the following steps.

1. Select fa equal to the highest frequency of the input signal
to be differentiated. Then, assuming a value of C1<1 F,
calculate the value of Rf
2. Calculate the values of R1and Cf so that R1C1=RfCf.
Differentiator has wide applications in

1. MonostableMultivibrator
2. Signal wave shaping
3. Function Generators.

4. CIRCUIT DIAGRAM:
Integrator:
Differentiator:

5. PROCEDURE:
Integrator:
3. Apply sine wave at the input terminals of the circuit using function Generator.
4. Connect channel-1 of CRO at the input terminals and channel-2 at the output
terminals.
o
5. Observe the output of the circuit on the CRO which is a cosine wave (90
phase shifted from the sine wave input) and note down the position, the
amplitude and the time period of Vin& Vo.
6. Now apply the square wave as input signal.
7. Observe the output of the circuit on the CRO which is a triangular wave and
note down the position, the amplitude and the time period of Vin& Vo.
8. Plot the output voltages corresponding to sine and square wave inputs.
Differentiator:
3. Apply sine wave at the input terminals of the circuit using function Generator.
4. Connect channel-1 of CRO at the input terminals and channel-2 at the output
terminals.
o
5. Observe the output of the circuit on the CRO which is a cosine wave (90
phase shifted from the sine wave input) and note down the position, the
amplitude and the time period of Vin& Vo.
6. Now apply the square wave as input signal.
7. Observe the output of the circuit on the CRO which is a spike wave and note
down the position, the amplitude and the time period of Vin& Vo.
8. Plot the output voltages corresponding to sine and square wave inputs.

Differentiator:
7. RESULT:
8. VIVA QUESTIONS:
1. What is an Integrator?
2. Draw the circuit of the Integrator using op-amp IC741.
3. Write down the expression for Vo of an Integrator.
4. Draw the frequency response of the Integrator and explain.
5. Draw the output waveform of the Integrator when the input is a Square wave.
6. What is the purpose behind the connection of Rf in the feedback path of
Integrator?
7. What are the applications of Integrator?
8. Why Rcomp is used in both Integrator and Differentiator circuits?
9. What is a Differentiator?
10. Draw the circuit of the Differentiator using op-amp IC741.
11. Write down the expression for Vo of a Differentiator.
12. Draw the output waveform of the Differentiator when the input is a Sine
wave.
13. Why R1 and Cf are connected in the circuit of the Differentiator?
14. What are the applications of Differentiator?

WEEK:3
EXPERIMENT NO: 3
st
a) 1 Order LOW PASS FILTER
1.AIM: To plot the frequency response of Butterworth LPF (First order) and
find the high cut-offfrequency.

Function Generator
CRO
Probes
Connecting Wires
741 Op-amp, Resistors, Capacitors
3.THEORY:
Filters are classified as follows:
Based on components used in the circuit
Active filters Use active elements like transistor or op-amp(provides
gain)
in addition to passive elements
Passive filters Use only passive elements like resistors, capacitors
and
inductors, hence no gain here.
Based on frequency range

Low pass filter(LPF) Allows low frequencies
High pass filter(HPF) Allows high frequencies
Band pass filter(BPF) Allows band of frequencies
Band reject filter(BRF) Rejects
band of frequencies All pass filter
Allows all frequencies but with a phase
shift
Active Filter is often a frequency selective circuit that passes a specified

band of frequencies and blocks or attenuates signals of frequencies outside this
band.
These Active Filters are most extensively used in the field of communications
and signal processing. They are employed in one form or another in almost all
sophisticated electronic systems such as Radio, Television, Telephone, Radar, Space
Satellites, and Bio-Medical Equipment.
Active Filters employ transistors or Op Amps in addition to that of resistors
and capacitors. Active filters have the following advantages over passive filters. (1)
Flexible gain and frequency adjustment. (2) No loading problem (because of high
input impedance and low output impedance) and
(3) Active filters are more economical than passive filters.
A first Order Low Pass Butterworth filter uses RC network for filtering.
Note that the op-amp is used in the non-inverting configuration; hence it does not
load down the RC network. Resistors R1 and RF determine the gain of the filter.
The gain magnitude equation of the Low Pass filter can be obtained by
converting equation
into its equivalent polar form, as follows.
2
| Vo / Vin | = AF/1+ (f / fH)
Where 1
fH = -------------------- = high cut-off frequency of the filter.
2 RC
The operation of the low pass filter can be verified from the gain magnitude equation.
1. At very low frequencies, that is f <fH
| Vo/Vin | = AF
2. At f = fH, | Vo/Vin | = AF/2 = 0.707 AF
3. At f >fH | Vo/Vin | < AF
Thus the Low Pass filter has a constant gain AF from 0 Hz to the almost
high cut-off frequency, fH, it has the gain 0.707AF at exactly fH, and after fH it
decreases at a constant rate with an increase in frequency. The gain decreases 20 dB
(= 20 log 10) each time the frequency is increased by 10. Hence the rate at which the
gain rolls off after fH is 20 dB/decade. The frequency f = fH is called the cut-off
frequency because the gain of the filter at this frequency is down by 3 dB (=20log
0.707) from 0 Hz. Other equivalent terms for cut-off frequency are -3dB frequency,
break frequency, or corner frequency.
4.DESIGN:
1. Choose a value for high cut-off frequency, fH(1 KHz) and a value for gain,
AF (2)
2. Assume a value of C 1F (0.1 F)
3. Calculate the value of R using the equation
4. Finally, select values of R1 and RF dependent on the desired pass band gain
AF using
AF = 1+ RF/R1 2 = 1+ RF/R1 RF = R1
5. Assume a value for R1(10K)and calculate RF.

5.CIRCUIT DIAGRAM:
(You can assume any value for C which is available in the

Lab)
6.PROCEDURE:

3. Connect channel -1 of CRO to input terminals (Vin) and channel -2 to output

terminals (Vo).
4. Set Vin = 1V & fin=10Hz using function generator.
5. By varying the input frequency in regular intervals, note down the output
voltage.
6. Calculate the gain (Vo/Vin) and Gain in dB = 20 log (Vo/Vin) at every
frequency.
7. Plot the frequency response curve (taking frequency on X-axis & Gain in dB
on Y-axis) using Semi log Graph.
8. Find out the high cut-off frequency, fH (at Gain= Constant Gain, Af 3 dB)
from the frequency response plotted.
9. Verify the practical (fH from graph) and the calculated theoretical cut-off
frequency (fH = 1/2RC ).
TABLE:
Vin = 1V
S.No. Input Frequency Output Voltage Gain Magnitude Gain in dB =
f(Hz) Vo (V) | Vo/Vin | 20log| Vo/Vin |

7.CALCULATIONS:
THEORETICAL Cut-off frequency:

fH = 1 / (2RC) = high cut-off frequency of the Low pass filter.
=
PRACTICAL Cut-off frequency (from Graph) :

fH = high cut-off frequency of
the Low pass filter = 3dB
cut-off frequency =
8.EXPECTED GRAPH:
9.RESULT:
8. VIVA QUESTIONS:
1. How filters are classified? Give one example for each classification.
2. What is an active filter and why it is called so?
3. How an active filter differs from a passive filter?
4. What are the advantages of active filters over passive filters?
5. Draw the circuit diagrams of active filters LPF and HPF.

st
b) 1 Order HIGH PASS FILTER
1.AIM: To plot the frequency response of Butterworth HPF (First order) and find the
low cut-offfrequency.

Function Generator
CRO
Probes
Connecting Wires
3.THEORY:
First Order High Pass Filter consists of RC network for filtering. First Order
High Pass filter can be constructed from a First Order Low Pass filter simply by
interchanging frequency determining components R & C . Op-Amp is used in the non
inverting configuration. Resistor R1 and RF determine the gain of the Filter.
The voltage gain magnitude equation of the second order High-pass filter is
V0 A F(f/fL)
----- = ----------------
2
Vin [1+(f/fL) ]
where AF = 1 + RF / R1
f = Operating (input) frequency.
1
fL = -------------------- = Low cut-off frequency of the filter.
2RC
This is the frequency at which the magnitude of the gain is 0.707 times its
pass band value. Obviously, all frequencies higher than fL are Pass Band frequencies,
with the highest frequency determined by the closed-loop bandwidth of the OP-Amp.
The operation of the highpass filter can be verified from the gain
magnitude equation. 1. At very low frequencies, that is f <fL
| Vo/Vin | < AF
2. At f = fL, | Vo/Vin | = AF/2 = 0.707 AF
3. At f >fL, | Vo/Vin | = AF
For example, in the first order High Pass filter the gain rolls off or
increases at the rate of 20dB/decade in stop band, that is for input signal frequency
lesser than Low cut-off frequency (fL ) ;
High Pass filter has constant gain AF, after the Low cut-off frequency
onwards (fL).
4.DESIGN: Follow the same procedure as given for low-pass filter.
5.CIRCUIT DIAGRAM:
6.PROCEDURE:
3. Connect channel -1 of CRO to input terminals (Vin) and channel -2 to output

terminals (Vo).
4. Set Vin = 1V & fin=10Hz using function generator.
5. By varying the input frequency in regular intervals, note down the output
voltage.
6. Calculate the gain (Vo/Vin) and Gain in dB = 20 log(Vo/Vin) at every
frequency.
7. Plot the frequency response curve (taking frequency on X-axis & Gain in dB
on Y-axis) using Semi log Graph.
8. Find out the low cut-off frequency, fL (at Gain= Constant Gain, Af 3 dB)
from the frequency response plotted.
9. Verify the practical (fL from graph) and the calculated theoretical cut-off
frequency (fL = 1/2RC).

TABLE:
Vin = 1V
S.No. Input Frequency Output Voltage Gain Magnitude Gain in dB =
f(Hz) Vo (V) | Vo/Vin | 20log| Vo/Vin |
7.CALCULATIONS:
THEORETICAL Cut-off frequency:

fL = 1 / (2RC) = Low cut-off frequency of the HPF.
=
PRACTICAL Cut-off frequency:

fL = Low cut-off frequency of the
HPF. = 3dB cut-off frequency
8.EXPECTED GRAPH:

9.RESULT
10. VIVA QUESTIONS:
1. Draw the frequency response of all filters (LPF, HPF, BPF, BRF and All-pass).
st nd
2. What is the gain roll off rate for a 1 order and 2 order filter?
3. What is the formula for cut-off frequency?
4. What is a 3 dB frequency and why it is called so?
5. What are the other names for 3 dB frequency?

WEEK-4:
EXPERIMENT NO:4
1.AIM: To design a Waveform Generator which generates Sine, Square and

Triangular waveforms usingIC741 and to verify its various output waveforms.

CRO
Probes
3.THEORY:
Waveform generator using IC741 is a circuit which generates Sine wave,

Square wave and Triangular wave. This circuit is a combination of Wien Bridge
oscillator, Zero crossing detector (Comparator with zero reference voltage) and
Integrator. The Wien Bridge oscillator generates Sine wave which is fed to the input
of Zero crossing detector. This detector gives the square wave output which is
connected to the input of the Integrator which in turn produces the Triangular wave
output.
The frequency of oscillations of the Sine wave output of Wien Bridge

oscillator is given by fo = 1/2RC
The frequency of oscillations of Square and Triangular wave outputs

will also be the same frequency as that of the Sine wave output.
For theory of individual circuits i.e. Wien Bridge oscillator, Zero

Crossing Detector and Integrator, please refer to the THEORY section of
respective experiments mentioned earlier in this manual.
4.DESIGN for Wien Bridge Oscillator:

1. Choose a desired frequency of oscillation, say fo =500 Hz.
2. Choose a value for capacitor C (0.1 F) and then calculate the value of R by
using the equation for fo (fo = 1/2RC).
3. Choose a value for R1 (10 K) and calculate the value of Rf from the
gain equation (Av = 1+Rf/R1 = 3). (Note: In practical, the value of Rf
may need to be varied to be more than the calculated value.)

5.CIRCUIT DIAGRAM:
Sine Wave Generator (Wien Bridge Oscillator):
Square Wave Generator (Zero Crossing Detector):
Triangular Wave Generator (Integrator):

6.PROCEDURE:
Sine wave Generator:

3. Connect output to the CRO.
4. Adjust the potentiometer to get an undistorted waveform.
5. Note down the amplitude and the time period, T of the sine wave and
calculate the frequency of oscillation, fo = 1 / T.
6. Verify the practical frequency of oscillation calculated in the preceding step
with the theoretical value, fo =1/2RC.
7. Plot the waveform.
Square wave Generator:

1. Switch OFF the power supply.
4. Connect the input to the channel-1 of CRO and output to the channel-2 of
CRO.
5. Observe the square wave output at channel-2 and note down the amplitude
and time period, T of the wave form.
6. Verify that the frequency of oscillation of both the input and the output waves
is same. Also verify that both the input and the output waves are in same
phase.
7. Plot the output waveform in accordance with the input waveform.
Triangular wave Generator:

1. Switch OFF the power supply.
4. Connect the input to the channel-1 of CRO and output to the channel-2 of
CRO.
5. Observe the triangular wave output at channel-2 and note down the amplitude
and time period, T of the wave form.
6. Verify that the frequency of oscillation of both the input and the output waves
o
is same. Also verify that the output wave is inverted i.e. 180 phase shift from
the input wave.
7. Plot the output waveform in accordance with the input waveform.

7.CALCULATIONS:
THEORETICAL
Frequency of
Oscillation fo =1/2RC
=
PRACTICAL
Frequency of
Oscillation fo =
1/T=
8.EXPECTED WAVEFORMS:
9.RESULT:
10.VIVA QUESTIONS:
1. What is a Function Generator?
2. What are the different stages in a Function Generator and how they are
connected?
3. Draw the output waveforms at different stages of Function Generator.
4. What is the relationship among the frequencies of output waveforms at
different stages of Function Generator?
5. Will there be any phase shift between the input and the output of any stage in
the Function Generator and what factor it depends on?
6. Why is Rcomp used in the circuit of Triangular wave generator?
7. Why is potentiometer used in the circuit of Wien Bridge Oscillator?

WEEK-5:
EXPERIMENT NO: 5
a) MonostableMultivibrator
1. AIM: To design a MonostableMultivibrator using IC555 and

compareitstheoretical and practicalpulse width.
2. APPARATUS: Bread
Board.
CRO Probes
Connecting
wires
555 Timer, Resistors, Capacitors
3. THEORY:
Monostablemultivibrator is also called as oneshot Multivibrator. When the
output is low, the circuit is in stable state, transistor T1 is ON and Capacitor C is
shorted to the ground. However, upon application of a negative trigger pulse to Pin
2, transistor T1 is turned OFF, which releases short circuit across the external
capacitor and drives the output High. The capacitor C now starts charging up toward
VCC through R. However when the voltage across the external capacitor equals 2/3
VCC, upper comparators output switches from low to high which in turn derives the
output to its low state. And the output of the flip flop turns transistor T1 ON, and
hence the capacitor C rapidly discharges through the transistor. The output of the
Monostable remains low until a trigger pulse is again applied. Then the cycle repeats.
The time during which the output remains high is given by
tp = 1.1 R C

Waveforms for IC555 Monostable Multivibrator
Once triggered, the circuits output will remain in the high state until the set
time tp elapses. The output will not change its state even if an input trigger is applied
again during this time interval t p.
4. DESIGN:
1. Choose a desired pulse width, say tp =1.1 ms.
2. Choose a value for capacitor C (0.1 F) and then calculate the value of R by
using the equation for tp.
5. CIRCUIT DIAGRAM:

6. PROCEDURE:
3. Connect function generator at the trigger input.
4. Connect channel-1 of CRO to the trigger input and channel-2 of CRO to the
output (Pin 3).
5. Using Function Generator, apply 1 KHz square wave with amplitude of
approx. equal to 9 Vpp at the trigger input.
6. Observe the output voltage with respect to input and note down the pulse
width and amplitude.
7. Now connect channel-2 of CRO across capacitor and observe the voltage
across the capacitor and note it down.
8. Compare the practical pulse width noted in the step above with its theoretical
value (tp=1.1 RC)
7. CALCULATIONS:
THEORETICAL Pulse width R = C =

tp = 1.1 RC =
PRACTICAL Pulse
width tp =

9. RESULT:
10. VIVA QUESTIONS:

1.What is the other name for monostable multivibrator?
2. when MSMV is in stable state ,what is the output level?
3. Why trigger is required in the case of MSMV?
4. which type of trigger pulse is required for MSMV?
5. What is the formula for the output pulse width of MSMV?
6. How long MSMV remains in stable state?

(b) AstableMultivibrator
1.AIM: To design an AstableMultivibrator using IC555 and compareitstheoretical and practical

timeperiod and duty cycle.
2. APPARATUS: Bread Board.

CRO Probes
Connecting wires
555 Timer, Resistors, Capacitors
3.THEORY:
An Astablemultivibrator, often called a free-running Multivibrator, is a rectangular-wave-
generating circuit. Unlike the Monostablemultivibrator, this circuit does not require an external
trigger to change the state of the output, hence the name free running. However, the time during
which the output is either high or low is determinate by the Two resistors and a capacitor, which
are externally connected to the 555 timer.
Figure 1 shows the 555 timer connected as an Astablemultivibrator. Initially, when the output is
high, capacitor C starts charging towards Vcc through RA and RB. However as soon as voltage
across the capacitor equals 2/3 Vcc, comparator 1 triggers the flip-flop, and the output switches
low. Now the capacitor C starts discharging through RB and the transistor Q 1. When the voltage
across C equals 1/3 Vcc, comparator 2s output triggers the flip-flop, and the output goes high.
Then the cycle repeats. The output voltage and the capacitor voltage waveforms are shown in the
following figures.
As shown in this figure, the capacitor is periodically charged and discharged between 2/3 Vcc and
1/3 Vcc, respectively. The time during which the capacitor charges from 1/3 Vcc to 2/3 Vcc is
equal to the time the output is high and is given by
tc = 0.69 (RA + RB) C (1)
Similarly, the time during which the capacitor discharges from 2/3 Vcc to 1/3 Vcc is equal to the
time the output is low and is given by
td = 0.69 (RB)C (2)
Thus the total time period of the waveform is
T = tc + td = 0.69(RA + 2RB) (3)
Therefore the frequency of oscillation is fo = 1/T = 1.45/(RA + 2RB)C
And% Duty cycle = (tc/T) *100 (4)

4.Circuit Diagram:
5.Expected Wave forms:
6. PROCEDURE:
3. Connect channel-1 of CRO to the output (Pin 3).
4. Observe the output voltage and note down the time period and duty cycle.
5. Now connect channel-2 of CRO across capacitor and observe the voltage across the
capacitor and note it down.
6. Compare the practical time period and duty cycle.

7.CALCULATIONS:
THEORETICAL
time periods tc = 0.69 (RA +
RB) C
td = 0.69 (RB)C
Total time period of the waveform, T = tc + td
% Duty Cycle = (tc / T) *100
PRACTICAL (from output waveforms)
time period, T = % Duty

cycle =
8.RESULT:
9.VIVA QUESTIONS:
1. What is the other name for Astablemultivibrator (AMV)?
2. What is the formula for the time period of the waveform of AMV?
3. What is the formula for the % of Duty cycle?

WEEK-6:
EXPERIMENT NO: 6
1. AIM: To study the Schmitt trigger characteristics by using IC741 and compare
theoretical and practicalvalues of the Upper Threshold voltage, VUT and the Lower
Threshold voltage, VLT.
2. APPARATUS: 741 Op-Amp

Resistors
Bread board
Function generator
CRO
Probes
Connecting wires
3. THEORY:
Circuit shows an inverting comparator with positive feedback. This circuit converts an
irregular shaped waveform to square wave or pulse. This circuit is known as Schmitt trigger or
Regenerative comparator or Squaring circuit. The input voltage Vin triggers (changes the state of
) the output Vo every time it exceeds certain voltage levels called Upper threshold voltage, VUT
and Lower threshold voltage, VLT. The hysteresis width is the difference between these two
threshold voltages i.e. VUT VLT. These threshold voltages are calculated as follows.
VUT = (R1/R1+R2) Vsat when Vo= Vsat
VLT = (R1/R1+R2) (-Vsat) when Vo= -Vsat
The output of Schmitt trigger is a square wave when the input is sine wave or triangular wave,
where as if the input is a saw tooth wave then the output is a pulse wave.
4. CIRCUIT DIAGRAM:
5. PROCEDURE:

3. Apply the input sine wave using function generator.

4. Connect the channel1 of CRO at the input terminals and Channel-2 at the output
terminals.
5. Observe the output square waveform corresponding to input sinusoidal signal.
6. Overlap both the input and output waves and note down voltages at positions on sine
wave where output changes its state. These voltages denote the Upper threshold voltage
and the Lower threshold voltage (see EXPECTED WAVEFORMS below).
7. Verify that these practical threshold voltages are almost same as the theoretical threshold
voltages calculated using formulas given in the THEORY section above.
8. Sketch the waveforms by noting down the amplitude and the time period of the input V in
and the output Vo.
TABLE:

7. RESULT:
8. VIVA QUESTIONS:
1. Which is type of comparator called Schmitt trigger using IC741?
2. What is the output wave of Schmitt trigger if the input is sine wave?
3. What type of waveform is obtained when triangular or ramp waveforms are applied to
Schmitt trigger circuit?
4. Explain how a square wave is obtained at the output of timer when sine wave input is
given?
5. What is the Threshold voltage?
6. How do you calculate the theoretical values of VUT and VLT in the case of IC741?
7. What is the Hysteresis width?
8. What is the minimum amplitude of the input sine wave in the case of Schmitt trigger
using IC741?

WEEK-7
EXPERIMENT NO: 7
1.AIM:
1. To study the operation of NE565 PLL
2. To use NE565 as a multiplier
2. EQUIPMENT AND COMPONENTS
3.APPARATUS
1. DC power supply 1 No.
2. CRO 1 No.
3. Breadboards 1 No.
4. Function Generator- 1 No.
4.THEORY
The 565 is available as a14-pin DIP package. It is produced by Signatic Corporation. The output
frequency of the VCO can be rewritten as
fo = 0.25 / RT CT Hz.
Where RT and CTare the external resistor and capacitor connected to pin8 and pin9. A value
between 2k and 20k is recommended for RT .The VCO free running frequency is adjusted with RT
and CT to be at the centre for the input frequency range
5.CIRCUIT DIAGRAM

6.PROCEDURE:
i. Connect the circuit using the component values as shown in the figure
ii .Measure the free running frequency of VCO at pin4 with the input signal
Vinset= zero. Compare it with the calculated value=0.25/RTCT
iii. Now apply the input signal of 1Vpp square wave at a1kHz to pin2
st
iv. Connect1 channel of the scope to pin2 and display this signal on the scope.
v .Gradually increase the input frequency till the PLL is locked to the input frequency. This
frequency f1 gives the lower ends of the capture range. Go on increase the input frequency; till
PLL tracks the input signal, say to a frequency f2.This frequency f2 gives the upper end of the
lock range. If the input frequency is increased further the loop will get unlocked.
vi. Now gradually decrease the input frequency till the PLL is a gain locked. This is the
frequency f3, the upper end of the capture range .Keep on decreasing the input frequency until
the loop is unlocked. This frequency f4 gives the lower end of the lock range
vii. The lock range fL=(f2 f4) compare it with the calculated value of (7.8 fo /12)
Also the capture range is fc=(f3 f1). Compare it with the calculated value of capture
3 1/2
range. fc = [fL / (2)(3.6)(10 )C]
viii To use PLL as a multiplier,make connections as show in fig. The circuit uses a 4-bit binary
counter7490 used as a divide-by-5circuit.
ix. Set the input signal at 1Vpp square wave at 500Hz
x..Vary the VCO frequency by adjusting the 20K potentiometer till the PLL is locked.
Measure the output frequency.
xi. Repeat step9 and10 for input frequency of 1kHz and 1.5kHz.

7.OBSERVATIONS:
fO = fL =
fC =
8.CALCULATIONS:
fL = (f2 f4) = 7.8fO /12

3 1/2
fC = (f3 f1) = [fL/(2) (3.6)(10 )C]
9.GRAPH:
10.RESULT:
11.VIVA QUESTIONS:
1. Which characteristic of PLL is defined as the range of frequencies over which

PLL can acquire lock with the input signal?
2. In PLL, the capture range is always in which lock range?
3. In the locked state of PLL, the phase error between the input & output is ?
4. In communication circuits, PLL is currently applicable for ?
5. How many Vcc connections does the 565 PLL use?
6. Which characteristic of PLL is defined as the range of frequencies over which PLL can
acquire lock with the input signal?
WEEK-8
EXPERIMENT No: 8
1.AIM
To study the Fixed Voltage Regulators (1) 7805

(2) 7809
(3) 7812
(4) 7912
(5) 723 Variable Voltage Regulator
2.Theory
DC power for electronic circuits is most conveniently obtained from commercial ac lines by
using rectifier - filter system,called a dc power supply. The rectifier-filter combination
constitutes an ordinary dc power supply .The dc voltage from an ordinary power supply remains
constant so long as ac mains voltageor load is unaltered . However, in many electronic
applications, it is desired that dc voltage should remain constant irrespective of changes in ac
mains or load. Under such situations, voltage regulating devices are used with ordinary power
supply. This constitutes regulated dc power supplyand keeps the dc voltage at fairly constant
value.
ORDINARY DC POWER SUPPLY

An ordinary or regulated dc power supply contains a rectifier and a filter circuit as shown in Fig-
1.
The output from the rectifier is pulsating dc. These pulsations are due to the presence of ac
component
in the rectifier output. The filter circuit removes the ac component so that steady dc voltage is
obtained acrossthe load.
Limitations :
An ordinary dc power supply has two following drawbacks:
1. The dc output voltage changes directly with input ac voltage.

2. The dc output voltage decreases as the load current increases. This is due
to voltage drop in (a) Transformer windings (b) Rectifier (c) Filter circuit
These variations in dc output voltage may cause inaccurate or erratic operation or even
malfunctioning of many electronic circuits. Eg. In an oscillator, the frequency will shift and in
transmitters, distorted output will result, Therefore, ordinary power supply is unsuited for many
applications and is being replaced by regulated power supply.
For comparison of different types of power supplies, the following terms are commonly used:
1. Voltage regulation : The dc voltage available depends upon load current. If the load current Idc
across the output terminals of a given power supply is increased by decreasing RL as in Fig-
2.There is greater voltage drop in the power supply and hence smaller dc output voltage will be
available . Reverse will happen if the load current decreases. The variation of output voltage
w.r.t.the amount of load current drawn from the power supply is known as voltage regulation and
is expressed by the following relation:
% voltage regulation = (VNL - VFL) / VFL * 100
VNL=dc output voltage at no load.
VFL=dc output voltage at full load
In a well designed power supply, the full load voltage is only slightly less than no -load voltage
I.e. voltage regulation approaches zero. Therefore, lower the voltage regulation, the lesser the
difference between full-load and no-load voltage and better is the power supply. Power supplies
used in practice have a voltage regulation of 1% i.e. full load voltage is within 1% of the no -load
voltage. Fig-3 shows the change of dc output voltage with load current. This is known as voltage
regulation curve.
2. MINIMUM LOAD RESISTANCE : The change of load connected to a power supply varies
the load current and hence the dc output voltage. In order that a power supply gives the rated
output voltage and current, there is minimum load resistance allowed. For instance, I a power
supply is required to deliver a full-load current IFL at full load voltage VFL, then,
3.REGULATED POWER SUPPLY
A dc power supply which maintains the output voltage constant irrespective of ac mains
fluctuations or load variations is known as regulated dc power supply. A regulated power supply
consists of an ordinary power supply and voltage regulating device an in fig-4. The output of
ordinary power supply is fed to the voltage regulator which produces the final output. The output
voltage (Vdc) remains constant whether the load current changes or there are fluctuations in the
input ac voltage.
NEED : In an ordinary power supply, the voltage regulation is poor i.e dc output voltage
changes appreciably with load current. Moreover, output voltage also changes due to
variations in the input ac voltage. This is due to the following reasons:-
i) In practice, there are considerable variations in ac line voltage caused by outside factors
beyond our control. This changes the dc output voltage. Most of the electronic circuits will
refuse to work satisfactorily on such output voltage fluctuations. This necessitates to use
regulated dc power supply.
ii) The internal resistance of power supply is relatively large (>30W). Therefore, output voltage is
markedly affected by the amount of load current drawn from the supply. These variations in
dc voltage may cause erratic operation of electronic circuits. Therefore, regulated dc
power supply is the only solution in such situations.
4.HARDWARE SPECIFICATIONS
1. Built - in 16V - 0 - 16V / 350mA

12V - 0 - 12V / 350mA
8V - 0 - 8V / 350mA AC sources
2.Bridge rectifier using IN4007 diodes - 1No.
3.
4.Fixed Voltage Regulator -7805, 7809, 7812,7912.
5. Variable Voltage Regulator using 723 IC
5.EXPERIMENTAL PROCEDURE
1. Connect the circuit as shown in fig - 4.
2. Connect different load resistors available in the front panel, note down the output current and
voltage.
3. Also test the circuit with 12V - 0 - 12V, 16V - 0 - 16V AC sources also.
4.Remove 7805 and connect 7809, 7812 also repeat 2 and 3 steps.
5.Connect the circuit shown in fig - 5.
7.EXPERIMENTAL PROCEDURE
1. Switch ON the experimental board by connecting power card to the AC mains.

2. Make sure that the potentiometer are in minimum position.
3. Connect the 8V AC tapping of the transformer secondary to the bridge rectifier input and short
Raw DC +Ve point and pin 12 of 723 ( See Fig- )
4. Measure the output voltage with a DMM and also measure the output with the 10KW
potentiometer with its maximum position.
5. Now, disconnect the 8V AC tapping and connect 10V AC tapping and notedown the minimum
and maximum output voltages with 10KW minimum and maximum positions.
6. Repeat the same procedure for 12V, 16V and 18V AC transformer secondary tapings and
tabulate these values in Table-1.
7. Now, again connect 8V AC to the bridge rectifier input, set the output DC voltage at 5V
with
10KW potentiometer.
8. Connect the load resistor with (0-50mA) milliammeter and vary the load resistor and note
down the readings of the output voltage and output current with different load resistor.
9. Calculate &Tabulate the load regulation at each load current.
% Regulation = (VNL - VFL)/VFL * 100
10. Draw a graph between load current Idc& load voltage Vdc regulation.
723 Regulator:
It is a monolithic voltage regulator constructed on a single silicon chip. The device consists of
temperature compensated reference amplifier,, error amplifier, power series pass transistor and
curren limit circuitry. Additional NPN or PNP pass element may be used when output currents
exceedin150mA are required. Provisions are made for adjustable current limiting and remote
shutdown. In Addition to the above the device features low stand by current drain, low
temperature drift and hig ripple rejections. The 723 is intended for use with positive or
negative supplies as a series, shunt , switching or floating regulator. Applications include
laboratory power supplies, air borne system and other power supplies for digital and linear
circuits.
6.CIRCUIT DESCRIPTION
Fig -4 shows the circuit of a variable regulator constructed with 723 IC. Pin is connected to
positive terminal of the supply. 10KW potentiometer connected to pin 4, controls the output
voltage.
Output is available at Pin10. This output is not sufficient to drive loads. So it is passed
through the Darlington pair of transistors (CL100).

8.RESULT:

9.VIVA QUESTIONS:
1. The 7812
regulator IC provides how much voltage?
2. Voltage
regulators keep a constant which output voltage when the input or load varies within
limits?
3. What is the
dropout voltage in a three terminal IC regulator?
4. To get a
maximum output current, IC regulation are provided with which device?
5. Which type
of regulator is considered more efficient?
6. How the
average temperature coefficient of output voltage expressed in fixed voltage
regulator?

WEEK:9
PROGRAM :9(A)
1.AIM:
To develop the source code for logic gates by using VERILOG and obtain the simulation.
2.SOFTWARE & HARDWARE:
1. XILINX 9.2i
2. FPGA-SPARTAN-3E
3.LOGIC DIAGRAM:
AND GATE: OR GATE:
LOGIC DIAGRAM: TRUTH TABLE:

LOGICDIAGRAM TRUTH TA BLE:
A B Y=AB A B Y=A+B
0 0 0 0 0 0
0 1 0 0 1 1
1 0 0 1 0 1
1 1 1 1 1 1
NOT GATE: NAND GATE:

LOGIC DIAGRAM: TRUTH TABLE: LOGICDIAGRAM TRUTH TABLE
A B Y=(AB)
A Y=A
0 0 1
0 0 0 1 1
0 1 1 0 1
1 1 0
NOR GATE: XOR GATE:

LOGIC DIAGRAM: TRUTH TABLE: LOGICDIAGRAM TRUTH TABLE:
A B Y=(A+B)
A B
0 0 1
0 1 0 0 0 0
1 0 0 0 1 1
1 1 0 1 0 1
1 1 0

XNOR GATE:
4.VERILOG SOURCE CODE:
module logicgates1(a, b,
c); input a;
input b;
OUTPUT: [6:0] c;
assign c[0]= a & b;
assign c[1]= a | b;
assign c[2]= ~(a &
b); assign c[3]= ~(a |
b); assign c[4]= a ^ b;
assign c[5]= ~(a ^ b);
assign c[6]= ~ a;
endmodule
Simulation output:
5.RESULT:
Thus the OUTPUTs of all logic gates are verified by simulating the VERILOG code.

6. VIVA QUESTIONS:
1. If a signal passing through a gate is inhibited by sending a low into one of the inputs, and the
output is HIGH, the gate is which one?
2. for which gate the output will be a LOW for any case when one or more inputs are zero ?
3. A single transistor can be used to build which of the following digital logic gate?
4. Exclusive-OR (XOR) logic gates can be constructed from what other logic gates?

PROGRAM :9(B)
1.AIM:
To develop the source code for 2-to-4 decoder by using VERILOG and obtain the simulation.
1. XILINX 9.2i
2. FPGA-SPARTAN-3E
3. DECODER LOGIC DIAGRAM:
TRUTH TABLE:
A B C Z(0) Z(1) Z(2) Z(3)
0 0 1 0 1 1 1
0 1 1 1 0 1 1
1 0 1 1 1 0 1
1 1 1 1 1 1 0
moduledecoderbehv(a, b, en, z);

input a;
input b;
input en;
output [3:0] z;
reg [3:0] z;
regabar,bbar;
always @ (a,b,en) begin
z[0] = (abar&bbar&en);
z[1] = (abar&b&en);
z[2] = (a&bbar&en);
z[3] = (a&b&en);
end
end module

5.Simulation output:
6.RESULT:
7.VIVA QUESTIONS:
1. A device that converts from decimal to binary numbered is called?

2. What is a Combinational circuit?
3. what is a Decoder?
4. . In 3: 8 decoder the no. of inputs are how many?
5. which circuit can be used as parallel to series converter?

WEEK:10
PROGRAM :10(A)
1.AIM:
To develop the source code for 8-to-3 encoder by using VERILOG and obtain the simulation.
1. XILINX 9.2i
2. FPGA-SPARTAN-3E
3.ENCODER LOGIC DIAGRAM:
TRUTH TABLE:
D0 D1 D2 D3 D4 D5 D6 D7 X Y Z
1 0 0 0 0 0 0 0 0 0 0
0 1 0 0 0 0 0 0 0 0 1
0 0 1 0 0 0 0 0 0 1 0
0 0 0 1 0 0 0 0 0 1 1
0 0 0 0 1 0 0 0 1 0 0
0 0 0 0 0 1 0 0 1 0 1
0 0 0 0 0 0 1 0 1 1 0
0 0 0 0 0 0 0 1 1 1 1
moduleencoderbehav(d, a,b,c);
input [7:0] d;
output x; output y; output z;
rega,b,c;
always @ (d [7:0])
begin a= d[4] | d[5] | d[6] | d[7];
b= d[2] | d[3] | d[6] | d[7];
c= d[1] | d[3] | d[5] | d[7];
end
endmodule
6.RESULT:
7.VIVA QUESTIONS:
1. How many 3-line-to-8-line decoders are required for a 1-of-32 decoder?
2. How many data select lines are required for selecting eight inputs?
3. The TTL 74LS148 is an 8-to-3 bit priority encoder has how many active low inputs?
4. when an input with a higher priority is present, then what happens to the all other inputs with a
lower priority?

PROGRAM :10(B)
1.AIM:
To develop the source code for 8x1 multiplexer and demultiplexer by using VERILOG and
obtain the simulation.
1. XILINX 9.2i
2. FPGA-SPARTAN-3E
3.MULTIPLEXER LOGIC DIAGRAM:

4. TRUTH TABLE:
5. VERILOG SOURCE CODE:

module MUX8TO1(sel, A,B,C,D,E,F,G,H, MUX_OUT);
input [2:0] sel;
input A,B,C,D,E,F,G,H;
output reg MUX_OUT;
always@(A,B,C,D,E,F,G,H,sel)
begin
case(sel)
3'd0:MUX_OUT=A;
3'd1:MUX_OUT=B;
3'd2:MUX_OUT=C;
3'd3:MUX_OUT=D;
3'd4:MUX_OUT=E;
3'd5:MUX_OUT=F;
3'd6:MUX_OUT=G;
3'd7:MUX_OUT=H;
default:; // indicates null
endcase
end
endmodule
6. Simulation output:

7. DEMULTIPLEXER LOGIC DIAGRAM:
8.RESULT:
9. VIVA QUSETIONS:
1. How many number of control lines for a 8 to 1 multiplexer?
2. The device which changes from serial data to parallel data is called?
3. The commercially available 8-input multiplexer integrated circuit in the TTL family is ?
4. The number of control lines for 32 to 1 multiplexer is ?
5. What is the function of Demultiplexer?

WEEK:11
PROGRAM :11(A)
1. AIM:
To develop the source code for 4 bit binary to gray converter by using VERILOG and
obtained the simulation.
2. SOFTWARE & HARDWARE:
1. XILINX 9.2i
2. FPGA-SPARTAN-3E
3.CODE CONVERTER (BCD TO GRAY) TRUTH TABLE:
BCD GRAY
0000 0000
0001 0001
0010 0011
0011 0010
0100 0110
0101 0111
0110 0101
0111 0100
1000 1100
1001 1101
4. LOGIC DIAGRAM:

5.Behavioral Modeling:
module b2g_behv(b,g);
input [3:0] b;
output [3:0] g; reg [3:0] g;
always@(b) begin
g[3]=b[3];
g[2]=b[3]^b[2];
g[1]=b[2]^b[1];
g[0]=b[1]^b[0];
end
endmodule
7. RESULT:
8. VIVA QUESTIONS:
1. Gray code is which type of code?
2. The M.S.B. of the gray code will be exactly equal to the first bit of the given binary number?explain?
3. 4 bit gray code can be converted into how many bits?
4. Gray to binary conversion can be implemented with what?
5.gray code belongs to a class of codes called as?

Program11(B):
1.AIM:
To develop the source code for 4-Bit comparator by using VERILOG and obtained the
simulation .
1. XILINX 9.2i
2. FPGA-SPARTAN-3E
3. 4-bit comparator LOGIC DIAGRAM:
module comparator ( a ,b ,equal ,greater ,lower );

output equal ;
output greater ;
output lower ;
input [3:0] a ;
input [3:0] b ;
always @ (a or b) begin
if (a<b) begin
equal = 0;
lower = 1;
greater = 0;
end else if (a==b) begin
equal = 1;
lower = 0;
greater = 0;
end else
begin
equal = 0;
lower = 0;
greater = 1;
end

end
endmodule
6.RESULT:
7. VIVA QUESTIONS:
1. A circuit which converts some binary code into a singular active output representing its numerical value is ?
2. A logic circuit which determines if one input is equal to another is called?
3. comparator requires which type of gate?
4. Why clamp diodes are used in comparator?
5. How to obtain high rate of accuracy in comparator?

WEEK:12
PROGRAM :12(A)
1.AIM:
To develop the source code for full adder using three modeling styles by using VERILOG
and obtained the simulation.
1. XILINX 9.2i
2. FPGA-SPARTAN-3E
3.FULL ADDER:
A B C SUM CARRY
0 0 0 0 0
0 0 1 1 0
0 1 0 1 0
0 1 1 0 1
1 0 0 1 0
1 0 1 0 1
1 1 0 0 1
1 1 1 1 1
Dataflow Modeling:
modulefulladddataflow(a, b, c, sum, carry);

input a;
input b;
input c;
output sum;
output carry;
assign#2 p=a&b;
assign#2 q=b&c;
assign#2 r=c&a;
assign#4 sum=a^b^c;
assign#4carry =(p1 | p2) | p3;
endmodule
Behavioral Modeling:

modulefuladbehavioral(a, b, c, sum, carry);
input a;
input b; input c;
output sum;
output carry;
regsum,carry; reg
p1,p2,p3;
always @ (a or b or c)
begin
sum = (a^b)^c;
p1=a & b;
p2=b & c;
p3=a & c;
carry=(p1 | p2) | p3;
end
endmodule
Structural Modeling:
modulefa_struct(a, b, c, sum, carry);
input a;
input b;
input c;
output sum;
output carry;
wire t1,t2,t3,s1
xor x1(t1a,b),
x2(sum,s1,c);
and a1(t1,a,b),
a2(t2,b,c),
a3(t3,a,c);
or o1(carry,t1,t2,t3);
endmodule

6.RESULT:
7.VIVA QUESTIONS:
1. How many minimum of NAND gates are use in full adder?

2. 3 bits full adder contains?
3. Full adder performs addition on?
4. What are the fundamental inputs assigned or configured in the full adder circuit ?
5. How does an arithmetic operation take place in binary adders?

Program 12 (B):
1.AIM:
To develop the source code for FLIP FLOPS by using VERILOG and obtained the
simulation.
1. XILINX 9.2i
2. FPGA-SPARTAN-3E
3. SR FLIPFLOP:
. LOGIC DIAGRAM: TRUTH TABLE:
Q(t) S R Q(t+1)
0 0 0 0
0 0 1 0
0 1 0 1
0 1 1 X
1 0 0 1
1 0 1 0
1 1 0 1
1 1 1 X
4. VERILOG SOURCE CODE:
module srflipflop(s, r, clk, rst, q, qbar);

input s;
input r;
input clk;
input rst;
output q;
output qbar;
regq,qbar;
always @ (posedge(clk) or posedge(rst)) begin
if(rst==1'b1) begin
q= 1'b0;qbar= 1'b1;
end
else if(s==1'b0 && r==1'b0)
begin

q=q;
qbar=qbar;
end
else if(s==1'b0 && r==1'b1)
begin
q= 1'b0; qbar= 1'b1;
end
else if(s==1'b1 &&r==1'b0)
begin
q= 1'b1;
qbar= 1'b0;
end
else
begin
q=1'bx;
qbar=1'bx;
end
end
endmodule
. JK FLIPFLOP:
Q(t) J K Q(t+1)
0 0 0 0
0 0 1 0
0 1 0 1
0 1 1 1
1 0 0 1
1 0 1 0
1 1 0 1
1 1 1 0

VERILOG SOURCE CODE:
modulejkff(j, k, clk, rst, q, qbar);

input j;
input k;
input clk;
input rst;
output q;
output qbar;
reg q;
regqbar;
always @ (posedge(clk) or posedge(rst)) begin
if (rst==1'b1)
begin
q=1'b0;
qbar=1'b1;
end
else if (j==1'b0 && k==1'b0) begin
q=q;
qbar=qbar;
end
else if (j==1'b0 && k==1'b1) begin
q=1'b0;
qbar=1'b1;
end
else if (j==1'b1 &&k==1'b0)
begin
q=1'b1;
qbar=1'b0;
end
else
begin
q=~q;
qbar=~qbar;
end
end
endmodule

Simulation output:
D FLIPFLOP:
Q(t) D Q(t+1)
0 0 0
0 1 1
1 0 0
1 1 1
moduledff(d, clk, rst, q,

qbar); input d;
inputclk;
input rst;
output q;
output
qbar;
reg q;
regqb
ar;
always @ (posedge(clk) or posedge(rst))
begin if (rst==1'b1)
begin
q=1'b0
;
qbar=1
'b1;
end
else if
(d==1'b0)
begin
q=1'b0;
qbar=1
'b1;
end
else
begin
q=1'b1;
qbar=1'b0;
end
end
endmodule
Simulation output:
T-FLIP FLOP
LOGIC DIAGRAM: TRUTH TABALE:

modulet_flip_flop ( t ,clk ,reset ,dout );

outputdout ;
input t ;
input clk ;
wireclk ; input
reset ;
initial dout = 0;
always @ (posedge (clk)) begin
if (reset)
dout<= 0;
else begin
if (t)
dout<= ~dout;
end
end
endmodule
Simulation output:
6.RESULT:
7.VIVA QUESTIONS:
1. How many flip-flops are required to make a MOD-32 binary counter?
2. How is a J-K flip-flop made to toggle?
3. How many flip-flops are in the 7475 IC?
4. How many flip-flops are required to produce a divide-by-128 device?
5.On a master-slave flip-flop, when is the master enabled?

WEEK: 13
PROGRAM 13:
1.AIM:
To develop the source code for 4-bit binary counter and BCD counter by using VERILOG
and obtained the simulation.
1. XILINX 9.2i
2. FPGA-SPARTAN-3E
3.LOGIC DIAGRAM
4.VERILOG SOURCE CODE
module Counter_4Bit ( clk ,reset ,dout );
output [3:0]
dout ; input clk
;
input reset ;
initialdout = 0;
always @ (posedge (clk))
begin if (reset)
dout<= 0;
else
dout<= dout + 1;
end
endmodule

BCD COUNTER
LOGIC DIAGRAM
VERILOG SOURCE CODE
moduleBCD_Counter ( clk ,reset ,dout );

output [3:0] dout ;;
inputclk ; input
reset ; initial
dout = 0 ;
always @ (posedge (clk))
begin if (reset)
dout<= 0;
else if (dout<=9) begin
dout<= dout + 1;
end else if (dout==9) begin
dout<= 0;
end
end
endmodule
Simulation output:
6.RESULT:
7.VIVA QUESTIONS:
1.Counters are used to count ?

2. The terminal count of a modulus-11 binary counter is?
3. How can a digital one-shot be implemented using HDL?
4. Integrated-circuit counter chips are used in numerous applications including?
5. When two counters are cascaded, the overall MOD number is equal to the which of their individual
MOD numbers?
6. Three decade counter would have how many BCD counters?

WEEK: 14
PROGRAM 14:
1.AIM:
To develop the source code for finite state machine design by using VERILOG and
obtained the simulation
1. XILINX 9.2i
2. FPGA-SPARTAN-3E
modulefsm_using_function (
clock , // clock
reset , // Active high, syn reset
req_0 , // Request 0
req_1 , // Request 1
gnt_0 , // Grant 0
gnt_1
);
//-------------Input Ports-----------------------------
input clock,reset,req_0,req_1;
//-------------Output Ports----------------------------
output gnt_0,gnt_1;
//-------------Input ports Data Type-------------------
//-------------Output Ports Data Type------------------
reg gnt_0,gnt_1;
//-------------Internal Constants--------------------------
parameter SIZE = 3 ;
parameter IDLE = 3'b001,GNT0 = 3'b010,GNT1 = 3'b100 ;
//-------------Internal Variables---------------------------
reg [SIZE-1:0] state ;// Seq part of the FSM
//----------Code startes Here------------------------
assignnext_state = fsm_function(state, req_0, req_1);
//----------Function for Combo Logic-----------------
function [SIZE-1:0] fsm_function;
input [SIZE-1:0] state ;
input req_0 ;
input req_1 ;
case(state)
IDLE : if (req_0 == 1'b1) begin
fsm_function = GNT0;
end else if (req_1 == 1'b1) begin
fsm_function= GNT1;
end else begin fsm_function =
IDLE;
end
GNT0 : if (req_0 == 1'b1) begin fsm_function
= GNT0;

end else begin

fsm_function = IDLE;
end
GNT1 : if (req_1 == 1'b1) begin
fsm_function = GNT1;
end else begin
fsm_function = IDLE;
end
default :fsm_function = IDLE;
endcase
endfunction
//----------Seq Logic-----------------------------
always @ (posedge clock)
begin : FSM_SEQ
if (reset == 1'b1) begin
state<= #1 IDLE;
end else begin
state<= #1 next_state;
end
end
//----------Output Logic-----------------------------
always @ (posedge clock)
begin : OUTPUT_LOGIC
if (reset == 1'b1) begin
gnt_0 <= #1 1'b0;
gnt_1 <= #1 1'b0;
end
else begin
case(state)
IDLE : begin
gnt_0 <= #1 1'b0;
gnt_1 <= #1 1'b0;
end
GNT0 : begin
gnt_0 <= #1 1'b1; gnt_1
<= #1 1'b0;
end
GNT1 : begin
gnt_0 <= #1 1'b0; gnt_1
<= #1 1'b1;
end
default : begin
gnt_0 <= #1 1'b0; gnt_1
<= #1 1'b0;
end
endcase
end
end // End Of Block OUTPUT_LOGIC
endmodule // End of Module arbiter

4.RESULT:
5.VIVA QUESTIONS:
1. Number of states require to accept string ends with 10 are?
2.How many tuples are in finite state machine?
3. Finite automata requires minimum how many number of stacks?
4. Number of final state require to accept in minimal finite automata?
5. Is FSM with output capability can be used to add two given integer in binary representation?

LEAD EXPERIMENTS
EXPERIMENT: 1
1. AIM:
To Design a RC Phase Shift Oscillators that the output frequency is 200 Hz.
2. EQUIPMENTS AND COMPONENTS:
(i). APPARATUS
1. CRO (Dualchannel) - 1 No
2. BreadBoard 1 No
3. DualChannelPower Supply 1 No
3.COMPONENTS:
1. 3.3k Resistor 1 No.

2. 33k Resistor 1No.
3. 1M Resistor 1 No.
4. 0.1 F Capacitor 1 No.
5. OperationalAmplifier 1 No.
4. THEORY:
The PhaseShift Oscillator consist of an operational amplifier as the amplifying stage and three
RC cascaded networks as the feed back circuits the amplifier will provide 180 degrees phaseshift.
The feed back network will provide another phase shift of 180 degrees.
5. CIRCUIT DIAGRAM:

R= 3.3K
C= 0.1F
R1= 33K
6. PROCEDURE:
i. Construct the circuit as shown in the circuit diagram.

ii.Adjust the potentiometer Rf such that an outputwave form is obtained.
iii.Calculate the outputwave form frequency and peaktopeak voltage.
iv. Compare the theoretical and practical values of the output waveform frequency
7. OBSERVATIONS:
The frequency of oscillation=
CALCULATIONS:
i.The frequency of oscillation fo is given by
fo= 1/2 = 0.065/RC
ii. The gain Av at the above frequency must be atleast 29
i.e., (Ro/R1)*29
iii.fo=200Hz
LetC=0.1f
Then
R = 0.065/200* 3.25k (choose3.3k)
To prevent the loading of the amplifier because of RC networks it is necessary that

R110RThereforeR1=10R=33k
ThenRF=29 (33 k) =957 k (chooseRF=1M)
8. GRAPH:

9. RESULT:
10. VIVA QUESTIONS:
1. An oscillator produces how many oscillations?

2. In a phase shift oscillator, we use how many RC sections?
3. In a phase shift oscillator, the frequency determining elements are?
4. An oscillator employs which feedback?
5. What is the frequency of RC phase shift oscillator?

EXPERIMENT: 2
1.AIM:
To Design Wein Bridge Oscillator so that the output frequency is 965 Hz.
2.EQUIPMENTS AND COMPONENTS:
1.CRO (Dualchannel) - 1 No
2. BreadBoard 1 No
3. DualChannelPower Supply 1 No
3.COMPONENTS:
1. 12k Resistor 1 No.

2. 50k Resistor 1No.
3. 3.3k Resistor 1 No.
4. 0.05 F Capacitor 1 No.
5. OperationalAmplifier 1 No.
4.THEORY:
In this oscillator the Wein Bridge Circuit is connected between the amplifier input terminals and
the output terminal. The bridge has a series RC network in one arm and parallel RC network in
the adjoining arm. In the remaining two arms of the bridge resistors R1 and RF are connected.
The total phase-shift around the circuit is 0o when the bridge is balanced.
5.CIRCUIT DIAGRAM:

R= 3.3K
C= 0.1F
R1= 33K
6. PROCEDURE:
i. Construct the circuit as shown in the circuit diagram.

ii.Adjust the potentiometer Rf such that an outputwave form is obtained.
iii.Calculate the outputwave form frequency and peaktopeak voltage.
iv. Compare the theoretical and practical values of the output waveform frequency
7. OBSERVATIONS:
The frequency of oscillation=
CALCULATIONS:
i.The frequency of oscillation fo is given by
fo= 1/2 = 0.065/RC
ii. The gain Av at the above frequency must be atleast 29
i.e., (Ro/R1)*29
iii.fo=200Hz
LetC=0.1f
Then
R = 0.065/200* 3.25k (choose3.3k)
To prevent the loading of the amplifier because of RC networks it is necessary that

R110RThereforeR1=10R=33k
ThenRF=29 (33 k) =957 k (chooseRF=1M)
8. GRAPH:
9. RESULT:
10. VIVA QUESTIONS:
1. A Wien bridge oscillator uses which Feedback?
2. For an Op-amp based wien Bridge Oscillator , if the oscillations stops after a few cycles, then
the cause is?
3. A Wien Bridge Oscillator circuit is required to generate a sinusoidal waveform of how much
frequency?
4. The Voltage gain of the amplifier must be?
5. The output resistance of the amplifier must be?

IC HDL Lab Manual

Uploaded by

Copyright:

Available Formats

IC HDL Lab Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

IC HDL Lab Manual

Uploaded by

Copyright:

Available Formats

IC Applications and HDL Simulation Lab Manual

HOLY MARY INSTITUTE OF TECHNOLOGY & SCIENCE

IC APPLICATIONS & HDL SIMULATION LAB

ELECTRONICS & COMMUNICATION ENGINEERING

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 1

Vision of the Department

To be a world leader and renowned for Electronics & Communication Engineering

Mission of the Department

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 2

LAB COURSE OUTCOMES:

CO1 Students will able to design circuits using

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 3

1. Do not handle any equipment without reading the instructions /Instruction

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 4

1 OP AMP Applications Adder, Subtractor,Comparators

2 Integrator and Differentiator Circuits using IC 741.

3 Active Filter Applications LPF, HPF (first order)

4 IC 741 Waveform Generators - Sine, Squarewave and

7 IC 565 - PLL Applications

8 Voltage Regulator using IC 723, Three Terminal Voltage

B) Design of 2-to-4 decoder

B) Design of 8-to-1 multiplexer and 1 x 8 demultiplexer.

B) Design of 4 bit comparator

B) Design of flip flops: SR, JK, T,D

1 Wein Bridge Oscillator

2 RC Phase shift Oscillator

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 5

APPARATUS: Bread Board

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 6

Comparator: A Comparator is a non-linear signal processor. It is an open loop mode

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 7

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 8

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 9

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 10

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 11

2.APPARATUS: Bread Board

Normally fa<fb. From the above equation, we can calculate Rf by assuming

In the circuit diagram of Integrator, the values are calculated by assuming fa

Integrator has wide applications in

Differentiator can be designed by implementing the following steps.

Differentiator has wide applications in

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 13

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 14

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 15

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 16

2.APPARATUS: Bread Board

Based on frequency range

Active Filter is often a frequency selective circuit that passes a specified

5. Assume a value for R1(10K)and calculate RF.

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 18

(You can assume any value for C which is available in the

1. Connect the components/equipment as shown in the circuit diagram.

3. Connect channel -1 of CRO to input terminals (Vin) and channel -2 to output

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 19

THEORETICAL Cut-off frequency:

PRACTICAL Cut-off frequency (from Graph) :

HOLY MARY INSTITUTE OF TECHNOLOGY&SCIENCE , BOGARAM,KEESARA. 20

2.APPARATUS: Bread Board

f = Operating (input) frequency.