Centillion 1200N Atm Switch Command Manual: Broadband STP

297-8013-904
Nortel Networks
BroadBand STP
Centillion 1200N ATM Switch
Command Manual
SSR3.0 Standard 1.01 August 2000
2000 Nortel
All rights reserved
Published in Canada
NORTEL NETWORKS CONFIDENTIAL: The information contained in this document is the property of Nortel
Networks. Except as specifically authorized in writing by Nortel Networks, the holder of this document shall keep the information
contained herein confidential, shall disclose the information only to its employees with a need to know, and shall protect the
information, in whole or in part, from disclosure and dissemination to third parties with the same degree of care it uses to protect
its own confidential information, but with no less than reasonable care. Except as expressly authorized in writing by Nortel
Networks, the holder is granted no rights to use the information contained herein.
Information subject to change without notice
Nortel Networks, the Nortel Networks logo, the Globemark, How the World Shares Ideas, and Unified Networks are trademarks
of Nortel Networks.
REGULATORY INFORMATION
Network Equiipment Building Systems (NEBS)

This product has been tested and found to comply with the criteria of NEBS level
1, 2, and 3.
FCC Part 15 Requirements

In compliance with FCC Part 15 Rules, the following statement is provided:
WARNING
This equipment generates, uses, and can radiate radio frequency energy and
if not installed and used in accordance with the instruction manual, may
cause interference to radio communications. It has been tested and found to
comply with the limits for a Class A computing device pursuant to Subpart J
of Part 15 of FCC Rules, which are designed to provide reasonable protec-
tion against such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interfer-
ence in which case the user at their expense will be required to take whatever
measures may be required to correct the interference.
FCC Part 68 Registration
Company Notification
If this product is provided with either a CE-DS1 or an ATM-DS1 interface then the
following applies:
Before installing the Centillion 1200N ATM Switch to the telephone network, the
telephone company must be provided with the following:
Your telephone number
The FCC registration number: AY5JPN-32775-XD-N
The required USOC jack is RJ45
Without a CE-DS1 or an ATM-DS1 interface, the Centillion 1200N FCC
registration number is 5CNJPN-32940-XD-N.
Service Requirements
In the event of equipment malfunction, Nortel Networks or an authorized
distributor of Nortel Networks will perform all repairs. It is the responsibility of
users requiring service to report the need for service to Nortel Networks or to one
of their authorized distributors.
Location of FCC Compliance Labels

Labels stating the Centillion 1200N ATM Switch FCC registration number and
compliance with FCC Part 15 and 68 are attached to the Base Chassis. The
appearance of the labels is as shown below:
Regulatory Information for Analog Telephone

The equipment uses the following USOC jacks: RJ45.
If the equipment causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required.
If advance notice is not practical, the telephone company will notify the customer
as soon as possible. Also, you will be advised of your right to file a complaint with
the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations,
or procedures that affect the operation of the equipment. If this happens, the
telephone company will provide advance notice in order for you to make necessary
modifications in order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact NEC America, Inc.s
National Technical And Support Center (NTAC) at 800-538-8166 for repair and/or
warranty information. If the trouble is causing harm to the telephone network, the
telephone company may request that you remove the equipment form the network
until the problem is resolved.
NO REPAIRS CAN BE DONE BY THE CUSTOMER.
IC CS03 Certification (Canada)

Certification number: 140 8642
Load Number of the equipment: N/A
NOTICE: The Industry Canada label identifies certified equipment. The
certification means that the equipment meets certain telecommunications network
protective operational and safety requirements. The department does not guarantee
the equipment will operate to the users satisfaction.
Before installing the equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection. In
some cases, the companies inside wiring associated with a single line individual
service may be extended by means of a certified connector assembly (telephone
extension cord). The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situation.
Repairs to certified equipment should b made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or installations made
by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request that the user disconnect the
equipment.
Users should ensure for their own protection that the electrical ground connections
of the power utility, telephone lines, and internal metallic water pipe system, if
present, are connected together. This protection may be particularly important in
rural areas.
CAUTION: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician, as
appropriate.
CAUTION: The act of monitoring or recording telephone conversations under
certain circumstances may violate federal or state statutes. Consultation with your
legal counsel prior to engaging in such practices would be advisable.
Safety Certifications
This equipment has been listed by Underwriters Laboratories and found to comply
with all the applicable requirements of the standard for Information Technology
equipment UL 1950 3rd edition. This equipment complies with CSA standard
C22.2 No 950 3rd edition.
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Instructions on Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Principal Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Entering Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Example Command Entry Formats . . . . . . . . . . . . . . . . . . . . . . 1-3
Command Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Commands Reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
General Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Privileged Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
ATM Switch Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
?/HELP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
BACKUP ? (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-3
BACKUP config (Privileged Command) . . . . . . . . . . . . . . . . . 3-4
CLEAR ? (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . . 3-5
CLEAR config (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-6
DEBUG ? (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . . 3-7
DEBUG ilmi (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-8
DEBUG pnni (Privileged Command) . . . . . . . . . . . . . . . . . . . . 3-9
DEBUG signaling (Privileged Command) . . . . . . . . . . . . . . . 3-12
DEBUG sscop (Privileged Command) . . . . . . . . . . . . . . . . . . 3-13
DELETE ? (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-14
DELETE cevc (Privileged Command) . . . . . . . . . . . . . . . . . . 3-15
DELETE configserver (Privileged Command) . . . . . . . . . . . . 3-16
DELETE dlci (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-17
DELETE froam (Privileged Command) . . . . . . . . . . . . . . . . . 3-18
DELETE frprofile (Privileged Command) . . . . . . . . . . . . . . . 3-19
DELETE ilmi (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-20
DELETE iproute (Privileged Command) . . . . . . . . . . . . . . . . 3-21
DELETE nms (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-22
DELETE oamcon (Privileged Command) . . . . . . . . . . . . . . . . 3-23
DELETE oamend (Privileged Command) . . . . . . . . . . . . . . . . 3-24
DELETE oamf5end (Privileged Command) . . . . . . . . . . . . . . 3-25
DELETE pnni (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-26
DELETE profile (Privileged Command) . . . . . . . . . . . . . . . . . 3-27
Centillion 1200N ATM Switch Command Manual i

NTP 279-8013-904
Table of Contents
DELETE shaper (Privileged Command) . . . . . . . . . . . . . . . . . 3-28

DELETE signaling (Privileged Command) . . . . . . . . . . . . . . . 3-29
DELETE tunneling (Privileged Command) . . . . . . . . . . . . . . . 3-30
DIAGNOSIS ? (Privileged Command) . . . . . . . . . . . . . . . . . . 3-32
DIAGNOSIS all (Privileged Command) . . . . . . . . . . . . . . . . . 3-33
DIAGNOSIS cpu (Privileged Command) . . . . . . . . . . . . . . . . 3-34
DIAGNOSIS slot (Privileged Command) . . . . . . . . . . . . . . . . 3-35
DIAGNOSIS switch (Privileged Command) . . . . . . . . . . . . . . 3-36
DISPLAY ? (General Command) . . . . . . . . . . . . . . . . . . . . . . 3-37
DISPLAY alarm (General Command) . . . . . . . . . . . . . . . . . . . 3-39
DISPLAY all (General Command) . . . . . . . . . . . . . . . . . . . . . 3-47
DISPLAY atmsig (General Command) . . . . . . . . . . . . . . . . . . 3-48
DISPLAY boot (General Command) . . . . . . . . . . . . . . . . . . . . 3-50
DISPLAY calledsoftpvp (General Command) . . . . . . . . . . . . 3-52
DISPLAY cdvt (General Command) . . . . . . . . . . . . . . . . . . . . 3-53
DISPLAY cevc (General Command) . . . . . . . . . . . . . . . . . . . 3-54
DISPLAY clock (General Command) . . . . . . . . . . . . . . . . . . . 3-56
DISPLAY configserver (General Command) . . . . . . . . . . . . . 3-57
DISPLAY configuration (General Command) . . . . . . . . . . . . 3-58
DISPLAY dlci (General Command) . . . . . . . . . . . . . . . . . . . . 3-59
DISPLAY dynamicroute (General Command) . . . . . . . . . . . . 3-61
DISPLAY ether (General Command) . . . . . . . . . . . . . . . . . . . 3-62
DISPLAY froam (General Command) . . . . . . . . . . . . . . . . . . 3-63
DISPLAY frprofile (General Command) . . . . . . . . . . . . . . . . 3-64
DISPLAY frversion (General Command) . . . . . . . . . . . . . . . . 3-66
DISPLAY iisp (General Command) . . . . . . . . . . . . . . . . . . . . 3-67
DISPLAY ilmi (General Command) . . . . . . . . . . . . . . . . . . . . 3-69
DISPLAY interface (General Command) . . . . . . . . . . . . . . . . 3-73
DISPLAY iproute (General Command) . . . . . . . . . . . . . . . . . 3-82
DISPLAY line (General Command) . . . . . . . . . . . . . . . . . . . . 3-83
DISPLAY looptime (General Command) . . . . . . . . . . . . . . . . 3-85
DISPLAY mac (General Command) . . . . . . . . . . . . . . . . . . . . 3-86
DISPLAY manufacturingid (General Command) . . . . . . . . . . 3-87
DISPLAY network (General Command) . . . . . . . . . . . . . . . . . 3-88
DISPLAY oamcon (General Command) . . . . . . . . . . . . . . . . . 3-90
DISPLAY oamend (General Command) . . . . . . . . . . . . . . . . . 3-91
DISPLAY oamf5end (General Command) . . . . . . . . . . . . . . . 3-94
DISPLAY pnni (General Command) . . . . . . . . . . . . . . . . . . . . 3-95
DISPLAY profile (General Command) . . . . . . . . . . . . . . . . . 3-103
DISPLAY pvc (General Command) . . . . . . . . . . . . . . . . . . . 3-104
DISPLAY redundancy (General Command) . . . . . . . . . . . . . 3-107
DISPLAY route (General Command) . . . . . . . . . . . . . . . . . . 3-109
DISPLAY scope (General Command) . . . . . . . . . . . . . . . . . . 3-110
DISPLAY scroll (General Command) . . . . . . . . . . . . . . . . . . 3-111
DISPLAY server (General Command) . . . . . . . . . . . . . . . . . 3-112
ii Centillion 1200N ATM Switch Command Manual

NTP 279-8013-904
Table of Contents
DISPLAY shaper (General Command) . . . . . . . . . . . . . . . . . 3-113

DISPLAY signaling (General Command) . . . . . . . . . . . . . . . 3-115
DISPLAY softpvp (General Command) . . . . . . . . . . . . . . . . 3-116
DISPLAY sscop (General Command) . . . . . . . . . . . . . . . . . . 3-119
DISPLAY status (General Command) . . . . . . . . . . . . . . . . . . 3-121
DISPLAY svc (General Command) . . . . . . . . . . . . . . . . . . . 3-123
DISPLAY svcline (General Command) . . . . . . . . . . . . . . . . 3-128
DISPLAY t309trg (General Command) . . . . . . . . . . . . . . . . 3-129
DISPLAY telnetlimit (General Command) . . . . . . . . . . . . . . 3-130
DISPLAY time (General Command) . . . . . . . . . . . . . . . . . . . 3-131
DISPLAY traffic (General Command) . . . . . . . . . . . . . . . . . 3-132
DISPLAY tunneling (General Command) . . . . . . . . . . . . . . . 3-146
DISPLAY version (General Command) . . . . . . . . . . . . . . . . 3-147
ENABLE (General Command) . . . . . . . . . . . . . . . . . . . . . . . 3-148
EXIT (General Command) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-150
EXIT (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . . . . 3-151
FAILUREDUMP (Privileged Command) . . . . . . . . . . . . . . . 3-152
FAILURELOG (Privileged Command) . . . . . . . . . . . . . . . . . 3-156
GENERATE ? (Privileged Command) . . . . . . . . . . . . . . . . . 3-157
GENERATE f4 (Privileged Command) . . . . . . . . . . . . . . . . 3-158
GENERATE f5 (Privileged Command) . . . . . . . . . . . . . . . . 3-159
GENERATE feac (Privileged Command) . . . . . . . . . . . . . . . 3-160
INSTALL config (Privileged Command) . . . . . . . . . . . . . . . 3-161
OPEN (General Command) . . . . . . . . . . . . . . . . . . . . . . . . . . 3-163
PASSWD (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-164
PVC ? (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . . . 3-165
PVC add (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-166
PVC delete (Privileged Command) . . . . . . . . . . . . . . . . . . . . 3-168
PVC establish (Privileged Command) . . . . . . . . . . . . . . . . . . 3-170
PVC flush (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-172
PVC remove (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-173
RESET ? (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-174
RESET slot (Privileged Command) . . . . . . . . . . . . . . . . . . . . 3-175
RESET switch (Privileged Command) . . . . . . . . . . . . . . . . . 3-176
ROUTE ? (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-177
ROUTE add (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-178
ROUTE delete (Privileged Command) . . . . . . . . . . . . . . . . . 3-180
ROUTE flush (Privileged Command) . . . . . . . . . . . . . . . . . . 3-181
ROUTE resume (Privileged Command) . . . . . . . . . . . . . . . . 3-182
SAVE (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . . . 3-183
SET ? (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . . . 3-184
SET atmsig (Privileged Command) . . . . . . . . . . . . . . . . . . . . 3-185
SET boot (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-186
SET calledsoftpvp (Privileged Command) . . . . . . . . . . . . . . 3-188
SET cdvt (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-189
Centillion 1200N ATM Switch Command Manual iii

NTP 279-8013-904
Table of Contents
SET cevc (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-191

SET clock (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-195
SET configserver (Privileged Command) . . . . . . . . . . . . . . . 3-197
SET dlci (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-198
SET ether (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-199
SET froam (Privileged Command) . . . . . . . . . . . . . . . . . . . . 3-200
SET frprofile (Privileged Command) . . . . . . . . . . . . . . . . . . 3-201
SET iisp (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-202
SET ilmi (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-204
SET interface (Privileged Command) . . . . . . . . . . . . . . . . . . 3-206
SET iproute (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-212
SET linestatus (Privileged Command) . . . . . . . . . . . . . . . . . . 3-213
SET local (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-215
SET loopback (Privileged Command) . . . . . . . . . . . . . . . . . . 3-216
SET looptime (Privileged Command) . . . . . . . . . . . . . . . . . . 3-217
SET mib (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-218
SET nms (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-219
SET oamcon (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-220
SET oamend (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-221
SET oamf5end (Privileged Command) . . . . . . . . . . . . . . . . . 3-222
SET pnni (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-223
SET profile (Privileged Command) . . . . . . . . . . . . . . . . . . . . 3-230
SET prompt (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-232
SET scope (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-233
SET scroll (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-234
SET server (Privileged Command) . . . . . . . . . . . . . . . . . . . . 3-235
SET shaper (Privileged Command) . . . . . . . . . . . . . . . . . . . . 3-236
SET signaling (Privileged Command) . . . . . . . . . . . . . . . . . . 3-237
SET sscop (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-238
SET svcline (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-239
SET t309trg (Privileged Command) . . . . . . . . . . . . . . . . . . . 3-240
SET telnetlimit (Privileged Command) . . . . . . . . . . . . . . . . . 3-241
SET time (Privileged Command) . . . . . . . . . . . . . . . . . . . . . . 3-242
SET tunneling (Privileged Command) . . . . . . . . . . . . . . . . . . 3-243
SOFTPVP ? (Privileged Command) Function . . . . . . . . . . . . 3-244
SOFTPVP addparty (Privileged Command) . . . . . . . . . . . . . 3-245
SOFTPVP delete (Privileged Command) . . . . . . . . . . . . . . . 3-246
SOFTPVP dropparty (Privileged Command) . . . . . . . . . . . . 3-247
SOFTPVP establish (Privileged Command) . . . . . . . . . . . . . 3-248
SOFTPVP flush (Privileged Command) . . . . . . . . . . . . . . . . 3-250
SOFTPVP release (Privileged Command) . . . . . . . . . . . . . . . 3-251
SOFTPVP setup (Privileged Command) . . . . . . . . . . . . . . . . 3-252
TELNETPASSWD (Privileged Command) . . . . . . . . . . . . . . 3-253
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
iv Centillion 1200N ATM Switch Command Manual

NTP 279-8013-904
1
Instructions on Commands
Principal Commands
The ATM Switch is controlled by entering commands from an external
Maintenance and Administration Terminal (MAT) connected via an RS-232C
interface.
The commands of the ATM Switch are divided into two types:
General Commands
Privileged Commands
While General Commands can only be used to see system data, Privileged
Commands can be used to set or change system data. Privileged Commands should
only be used by system managers and service personnel. The execution of a
Privileged Command requires the entry of a password registered in advance.
Commands are divided into the two types to prevent system data and network-
related data from being changed by unauthorized personnel.
The mode in which General Commands (only) can be used is referred to as the
General Command Mode. The mode in which both General Commands and
Privileged Commands can be used is referred to as the Privileged Command Mode.
When the power is turned on, the ATM Switch defaults to General Command
Mode.
To change from the General Command Mode to the Privileged Command Mode,
execute the ENABLE command.
NOTE All commands may be shortened at the command line for quicker entry; however,
there is no listing of abbreviated commands. Simply type the fewest number of
letters until the command displays. For example:
Long: HOSTNAME#show interface
Short: HOSTNAME#sh int
Centillion 1200N ATM Switch Command Manual 1-1

NTP 279-8013-904
Principal Commands Instructions on Commands
The ATM Switch will then prompt for a password. The password is set on the initial
entry into Privileged Mode, whereby the ATM Switch will prompt for a new
password and verification, along with a Telnet password and verification.
To change from the Privileged Command Mode to the General Command Mode,
execute the EXIT command.
The format of the prompt displayed on the MAT screen is used to determine
whether the current mode is the General Command Mode, indicated by the >
prompt, or the Privileged Command Mode, indicated by the # prompt. In addition,
if a host name is set to the system, the host name is also displayed as part of the
prompt. The host name is set by executing the SET LOCAL command.
Default Prompt
General Command Mode: HOSTNAME>
Privileged Command Mode: HOSTNAME#
1-2 Centillion 1200N ATM Switch Command Manual

NTP 279-8013-904
Instructions on Commands Entering Commands
Entering Commands
A command is entered after the prompt (> or #). While some commands are used
alone, many are used in combination with a subcommand or parameter. When
entering a subcommand or parameter, enter a [space] to divide the entries.
Some parameters can be defaulted while others cannot, depending on the type of
command and the conditions of specification. In this manual, parameters that can
be defaulted are enclosed in brackets, such as {P1}. When you have finished
entering a command, press the [ENTER] key.
A command may be entered in capital letters or lower case letters; however, the
password is case sensitive.
Example General Command Mode

Command Entry 1. >Command[ENTER]
Formats
Example: HOSTNAME>enable[ENTER]
2. >Command[space]Subcommand[ENTER]
Example: HOSTNAME>show[space]time[ENTER]
3. >Command[space]Subcommand[space]Parameter1[ENTER]
Example: HOSTNAME>show[space]pvc[space]00[ENTER]
Privileged Command Mode

1. #Command[ENTER]
Example: HOSTNAME#save[ENTER]
2. #Command[space]Subcommand[ENTER]
Example: HOSTNAME#save[space]act[ENTER]
3. #Command[space]Subcommand[space]Parameter1[space]
Parameter2[space]...[ENTER]
Example: HOSTNAME#set[space]local[space]switch1
[space]10.5.1.50[space]255.255.255.0[space]3900
[ENTER]

NTP 279-8013-904
Command Help Instructions on Commands
Command Help
Help is available for each command. Use HELP or ? for a brief description of each
command and learn the types of parameters and their possible setting ranges.
Following are example Help Commands.
.
Command Function
#?[ENTER] Displays list of commands that can be entered in General
Mode or Privileged Mode and a brief description.
#COMMAND?[ENTER] Displays list of subcommands that follow the specified
commands and a brief description.
#COMMAND[space] Displays the next parameter and the possible setting ranges.
Subcommand?[ENTER] (Displays types of parameters and possible setting ranges
following the specified command+subcommand.)
Example:
#DELETE configserver ?
0-3 LECS index
#COMMAND[space]Subcommand[space] Displays the next parameter and the possible setting ranges.
P1[space]?[ENTER] (If there is more than one parameter, the types of parameters
and their possible setting ranges following the specified
command+subcommand+parameter will be displayed.)
Example:
#DELETE configserver 0 ?
ATM ADDRESS LECS ATM address (up to 20-octet)
NOTE Entering ? after a command only shows the next parameter versus all parameters.
For example, if a command has five parameters and a ? is typed after entering two
of them, only the next parameter is shown, not the remaining three.
ATM Switch commands are described in "Commands" on Page 3-1.

Error messages are described in "Error Messages" on Page 4-1.

NTP 279-8013-904
2
Commands Reference
General Commands
Command Sub-Command Function Page

?/HELP - Command help 3-1
DISPLAY/SHOW ? DISPLAY command help 3-37
alarm Display alarm information 3-39
all Display all configuration data 3-47
atmsig Display Q.2931 parameter 3-48
boot Display boot mode 3-50
calledsoftpvp Display recognition standard of called 3-52
SoftPVP
cdvt Display cell delay variation tolerance 3-53
(CDVT) configuration
cevc Display circuit emulation connection 3-54
information
clock Display clock mode 3-56
configserver Display ILMI ATM address table of LAN 3-57
emulation configuration server (LECS)
configuration Display all configuration data 3-58
dlci Display DLCI data 3-59
dynamicroute Display dynamic routing table 3-61
ether Display IP address of Ethernet 3-62
froam Display OAM endpoint information 3-63
(FR-ATM).
frprofile Display FR profile information 3-64

NTP 279-8013-904
General Commands Commands Reference

DISPLAY/SHOW frversion Display ROM/software version of FR card 3-66
iisp Display ON/OFF status of Split Horizon, 3-67
loopcheck, and swaproute
ilmi Display ILMI connection information 3-69
interface Display line interface information 3-73
iproute Display IP routing information via ATM, or 3-82
Ethernet
line Display line status 3-83
looptime Display per port clock recovery status; on 3-85
or off
mac Display MAC address 3-86
manufacturingid Display manufacturing ID number 3-87
network Display network information 3-88
oamcon Display OAM connecting point information 3-90
oamend Display OAM end point information 3-91
oamf5end Display F5 OAM endpoint information 3-94
pnni Display PNNI connection information 3-95
profile Display profile information 3-103
pvc Display PVC information 3-104
redundancy Display redundancy of the server card 3-107
route Display SVC routing table 3-109
scope Display Scope 3-110
scroll Display MAT display line count 3-111
server Display TATP server IP address 3-112
shaper Display shaping rate 3-113
signaling Display signaling connection information 3-115
softpvp Display soft PVPC/PVCC setting 3-116
information
sscop Display SSCOP parameter 3-119
status Display hardware status 3-121
svc Display SVC connection table 3-123
svcline Display signaling line status 3-128
t309trg Display signaling line failure timing 3-129

NTP 279-8013-904
Commands Reference General Commands

DISPLAY/SHOW telnetlimit Display time limit of Telnet 3-130
time Display system date/time 3-131
traffic Display call traffic counter values 3-132
tunneling Display tunneling connection information 3-146
version Display ROM/Software Version 3-147
ENABLE - Go to Privileged Mode 3-148
EXIT - Log out during Telnet connection 3-150
OPEN - Open an access to a server card 3-163

NTP 279-8013-904
Privileged Commands Commands Reference
Privileged Commands

?/HELP - Command help 3-1
BACKUP ? BACKUP command help 3-3
config Backup configuration data 3-4
CLEAR ? CLEAR command help 3-5
config Initialize all configuration data 3-6
DEBUG ? DEBUG command help 3-7
ilmi Set ILMI debug flag 3-8
pnni Set PNNI debug flag 3-9
signaling Set Q.2931 debug flag 3-12
sscop Set SSCOP debug flag 3-13
DELETE ? Delete command help 3-14
cevc Delete circut emulation information 3-15
configserver Delete ILMI ATM address table entry of 3-16
LAN emulation configuration server
dlci Delete DLCI data 3-17
froam Delete OAM endpoint information 3-18
(FR-ATM)
frprofile Delete FR profile information 3-19
ilmi Delete ILMI connection (0, 16) 3-20
iproute Delete IP routing information 3-21
nms Delete NMS information 3-22
oamcon Delete OAM connecting point 3-23
oamend Delete OAM endpoint 3-24
oamf5end delete F5 OAM endpoint 3-25
pnni Delete PNNI connection (0, 18) 3-26
profile Delete profile information 3-27
shaper Delete shaping rate 3-28
signaling Delete signaling connection (0, 5) 3-29
tunneling Delete tunneling connection 3-30
information

NTP 279-8013-904
Commands Reference Privileged Commands

DIAGNOSIS ? DIAGNOSIS command help 3-32
all Diagnose all units 3-33
cpu Diagnose CPU board 3-34
slot Diagnose line packages 3-35
switch Diagnose switch board 3-36
EXIT - Go to General Mode 3-151
FAILUREDUMP Display failure information 3-152
FAILURELOG Display failure log 3-156
GENERATE ? GENERATE command help 3-152
f4 Generate OAM cells (loopback cells) in 3-158
the "f4" mode
f5 Generate OAM cells (loopback cells) in 3-159
the "f5" mode
feac Transmit FEAC code at DS3 package 3-160
INSTALL config system Install software or configuration data 3-161
via ATM or ethernet line
OPEN - Open an access to a CPU built-in card, 3-163
for example LAE/IPOA card
PASSWD - Set Privileged Mode password 3-164
PVC ? PVC command help 3-165
add Add PVC end point (P-to-MP) 3-166
delete Delete PVC 3-168
establish Build a PVC connection 3-170
flush Delete all PVC connections (for each 3-172
line)
remove Delete PVC end point (P-to-MP) 3-173
RESET ? RESET command help 3-174
slot Reset line card 3-175
switch Reset system 3-176

NTP 279-8013-904

ROUTE ? ROUTE command help 3-177
add Set SVC routing table 3-178
delete Delete one entry from SVC routing 3-180
table
flush Delete all entries from SVC routing 3-181
table
resume Resume SVCs across a previous link 3-182
SAVE - Save configuration 3-183
SET ? Set command help 3-184
atmsig Set Q.2931 parameter 3-185
boot Set boot mode 3-186
calledsoftpvp Switch recognition standard of called 3-188
SoftPVP
cdvt Set CDVT configuration 3-189
cevc Set circuit emulation connection 3-191
information
clock Set clock mode (master, slave) 3-195
configserver Set ILMI ATM address table of LAN 3-197
emulation configuration server
dlci Set DLCI data 3-198
ether Set Ethernet IP address 3-199
froam Set OAM endpoint information 3-200
(FR-ATM)
frprofile Set FR profile information 3-201
iisp Set ON/OFF status of Split Horizon, 3-200
loopcheck or swaproute
ilmi Enable ILMI and set configuration 3-204
interface Set port configuration 3-206
iproute Set IP routing information 3-212
linestatus Set line status; up or down 3-213
local Set Switch name, ATM IP address, 3-215
mask, and ATM prefix information
loopback Set loopback on line interface 3-216
looptime Set per port clock recovery 3-217
mib Set MIB contact/location information 3-218

NTP 279-8013-904
Commands Reference Privileged Commands

SET nms Set NMS information 3-219
oamcon Set OAM connecting point 3-220
oamend Set OAM endpoint 3-221
oamf5end Set F5 OAM endpoint 3-222
pnni Set PNNI configuration 3-222
profile Set UPC (policing) information 3-230
prompt Set prompt type 3-232
scope Set Scope 3-233
scroll Set MAT display line count 3-234
server Set server IP address 3-235
shaper Set shaping rate 3-236
signaling Set signaling connection 3-237
sscop Set SSCOP information 3-238
svcline Enable/disable signaling 3-239
t309trg Set signaling line failure timing 3-240
telnetlimit Set time limit of Telnet 3-241
time Set system date/time 3-242
tunneling Set tunneling connection information 3-243
SOFTPVP ? SOFTPVP command help 3-244
addparty Add soft PVPC/PVC end point 3-245
(P-to-MP)
delete Delete soft PVPC/PVCC 3-246
dropparty Delete soft PVPC/PVCC end point 3-247
(P-to-MP)
establish Set soft PVPC/PVCC 3-248
flush Delete soft PVPC/PVCC (for each line) 3-250
release Delete soft PVPC/PVCC 3-251
setup Set soft PVPC/PVCC by PNNI 3-252
TELNETPASSWD - Set Telnet password 3-253

NTP 279-8013-904
This page is for your notes.

NTP 279-8013-904
3
Commands
ATM Switch Commands

NOTE The Centillion 1200N is a 2.5 Gbps ATM switch.
For details on command error messages, see "Error Messages" on Page 4-1.
?/HELP Function
This command is used to display system commands.
Format
HOSTNAME# HELP
Output (General Mode)
DISPLAY<cmd> Display configuration data.

(Type "display ?" for list.)
ENABLE Enable privileged commands

(Password required)
EXIT Exit from privileged mode or close

current Telnet session
?/HELP Show available commands
OPEN Enable access to cards CPU
SHOW<cmd> Display configuration data

(Type "show ?" for list.)

NTP 279-8013-904
ATM Switch Commands Commands
Output (Privileged Mode)
BACKUP<cmd> Backup configuration data
CLEAR<cmd> Clear configuration data or traffic counter (Type "clear

?" for list.)
DEBUG<cmd> Debug protocol (Type "debug ?" for list.)
DELETE<cmd> Delete configuration data (Type "delete ?" for list.)
DIAGNOSIS<cmd> Diagnose hardware (Type "diagnosis ?" for list.)
DISPLAY<cmd> Display configuration data (Type "display ?" for list.)
ENABLE Enable privileged commands(Password required)
EXIT Exit from privileged mode or close current Telnet session
GENERATE<cmd> Generate OAM cells (Type "generate ?" for list.)
?/HELP Show available commands
INSTALL Install system files or configuration data. OPEN Enable

access to card's CPU
PASSWD Change password
PVC<cmd> PVC commands (Type "pvc ?" for list.)
RESET<cmd> Reset switch/line card (Type "reset ?" for list.)
ROUTE<cmd> Configure SVC routing table (Type "route ?" for list.)
SAVE Save configuration data to flash memory
SET<cmd> Set configuration data (Type "set ?" for list.)
SHOW<cmd> Display configuration data (Type "show ?" for list.)
SOFTPVP<cmd> Softpvp commands

(Type "softpvp ?" for list.)
TELNETPASSWD Change Telnet password
NOTE The output for ? or HELP lists all possible commands in General Mode and
Privileged Mode.

NTP 279-8013-904
Commands ATM Switch Commands
BACKUP ? Function
(Privileged This command is used to display the help message for the BACKUP command.
Command)
Format
HOSTNAME# BACKUP ?
Output
config Backup configuration data

NTP 279-8013-904
BACKUP config Function

(Privileged This command is used to back up configuration data from the DRAM into the
Command) specified Trivial File Transfer Protocol (TFTP) server.
Format
HOSTNAME# BACKUP config P1 P2
Format Explanation
P1 : Server IP address (x.x.x.x (x=0~255))
P2 : Configuration directory file name (max. 127 characters)
Example
HOSTNAME# Backup config 10.1.1.3 /user/2.5G/config.file
Output
<File name>....!......
Configuration data have been written?
NOTE 1. This command uses a TFTP server to write binary data to a backup file. A
blank file MUST be created on the TFTP server beforehand to allow a TFTP
write to work properly.
2. The backup file must be accessible for reading and writing; otherwise an error
message will be displayed.
3. "!" will be displayed if the command is retried due to timeout (2, 4, 8, 16, 32
sec.) during transmitting and 64 sec time-out will result in command error.

NTP 279-8013-904
CLEAR ? Function
(Privileged This command is used to display the help message for the CLEAR command.
Command)
Format
HOSTNAME# CLEAR ?
Output
config Clear configuration data
NOTE This command will clear all of your configuration data and reset the switch to
factory default. It should only be used by your network administrator.

NTP 279-8013-904
CLEAR config Function

(Privileged This command is used to initialize all the configuration data currently saved and
Command) reset the system.
Format
HOSTNAME# CLEAR config
Output
If Y is entered in response to the confirmation message:
Are you sure [Y or N] ? y
Do not push reset button until save finishes.

#####
The system coming up now.

If you want to enter boot program, push [ESC] key immediately.
If the [ESC] key is detected within 3 seconds, boot program is

loaded.
Otherwise, online program will be loaded from the flash memory.:
If anything other than Y is entered in response to the confirmation message:
Are you sure [Y or N] ? n
Configuration data stored in flash memory is not erased !
NOTE This command will clear all of your configuration data and reset the switch to
factory default. It should only be used by your network administrator. System
passwords are not affected.

NTP 279-8013-904
DEBUG ? Function
(Privileged This command is used to display the help message for the DEBUG command.
Command)
Format
HOSTNAME# DEBUG ?
Output
ilmi ILMI debug flag

pnni PNNI debug flag
signaling Q.2931 debug flag
sscop SSCOP debug flag
NOTE Debug information is only displayed on a RS-232 connected MAT. Debug

information is not displayed over a Telnet session.

NTP 279-8013-904
DEBUG ilmi Function

(Privileged This command is used to turn on the display tree for DEBUG ilmi.
Command)
Format
HOSTNAME# DEBUG ilmi P1 {P2}
Format Explanation
P1: Flag ID
0 - off ILMI flag off
1 - on ILMI flag on
P2: Line number (00~33)
Output
ILMI debug flag has been set.

NTP 279-8013-904
DEBUG pnni Function

(Privileged This command is used to set a flag for Private Network-Network Interface (PNNI)
Command) debugging.
If this flag is set, the PNNI unit outputs a message to the MAT each time it receives
a signaling message.
Format
HOSTNAME# DEBUG pnni P1 {P2} {P3}
Format Explanation
P1 : Flag ID
"00" or "disable" all flags off
"01" or "event" event flag on
"02" or "process" process flag on
"03" event and process flag on
"04" or "data" data flag on
"05" event and data flag on
"06" process and data flag on
"07" event, process, and data flag on
"08" error flag on
"09" event and error flag on
"10" process and error flag on
"11" event, process, and error flag on
"12" data and error flag on
"13" event, data, and error flag on
"14" process, data, and error flag on
"15" event, process, data, and error flag on
"16" or "packet" packet flag on
"17" event and packet flag on
"18" process and packet flag on
"19" event, process, and packet flag on
"20" data and packet flag on
"21" event, data, and packet flag on
"22" process, data, and packet flag on

NTP 279-8013-904
"23" event, process, data, and packet flag on

"24" error and packet flag on
"25" event, error, and packet flag on
"26" process, error, and packet flag on
"27" event, process, error, and packet flag on
"28" data, error, and packet flag on
"29" event, data, error, and packet flag on
"30" process, data, error, and packet flag on
"31" All flags on
P2 : Packet type (flag)
"00" or "hello" to specify a logical port number without specifying a
packet type
"01" hello select
"02" or "PTSP" PTSP select
"03" hello and PTSP select
"04" or "PTSP Ack." PTSP Ack. select
"05" hello and PTSP Ack. select
"06" PTSP and PTSP Ack. select
"07" hello, PTSP and PTSP Ack. select
"08" or "DSSummary" DS Summary select
"09" hello and DS Summary select
"10" PTSP and DS Summary select
"11" hello, PTSP and DS Summary select
"12" PTSP Ack. and DS Summary select
"13" hello, PTSP Ack. and DS Summary select
"14" PTSP, PTSP Ack. and DS Summary select
"15" hello, PTSP, PTSP Ack. and DS Summary select
"16" or "PTSEReq." PTSE Req. select
"17" hello and PTSE Req. select
"18" PTSP and PTSE Req. select
"19" hello, PTSP and PTSE Req. select
"20" PTSP Ack. and PTSE Req. select
"21" hello, PTSP Ack. and PTSE Req. select

NTP 279-8013-904
"22" PTSP, PTSP Ack., and PTSE Req. select

"23" hello, PTSP, PTSP Ack,. and PTSE Req. select
"24" DS Summary and PTSE Req. select
"25" hello, DS Summary, and PTSE Req. select
"26" PTSP, DS Summary, and PTSE Req. select
"27" hello, PTSP, DS Summary, and PTSE Req. select
"28" PTSP Ack., DS Summary, and PTSE Req. select
"29" hello, PTSP Ack., DS Summary, and PTSE Req. select
"30" PTSP, PTSP Ack., DS Summary, and PTSE Req.
select
"31" hello, PTSP, PTSP Ack., DS Summary, and PTSE
Req. select
P3 : Logical port number (00~157)
Output
PNNI debug flag has been set.

NTP 279-8013-904
DEBUG signaling Function

(Privileged This command is used to set a flag for Q.2931 debugging.
Command) If this flag is set, the Q.2931 unit outputs a message to the MAT each time it receives
a signaling message.
Format
HOSTNAME# DEBUG signaling P1
Format Explanation
P1 : Flag ID
00 - disable all "flag" types
01 - or event - event flag on
02 - or packet - packet flag on
03 - event and packet flag on
04 - error flag on
05 - event and error flag on
06 - packet and error flag on
07 - all flag on (error, packet and event)
Output
Q.2931 debug flag has been set.


NTP 279-8013-904
DEBUG sscop Function

(Privileged This command is used to set a flag for SSCOP debugging.
Command) If this flag is set, the SSCOP unit outputs a message to the MAT each time it receives
a SSCOP message.
Format
HOSTNAME# DEBUG sscop P1
Format Explanation
P1 : Flag ID
00 - disable all flag types
01 - event flag on
02 - packet flag on
03 - event and packet flag on
04 - error flag on
05 - event and error flag on
06 - packet and error flag on
07 - all flag on (error, packet, and event)
Output
SSCOP debug flag has been set.


NTP 279-8013-904
DELETE ? Function
(Privileged This command is used to display the help message for the DELETE command.
Command)
Format
HOSTNAME# DELETE ?
Output
cevc Circuit emulation configuration

configserver Configuration server information
ilmi ILMI connection
iproute IP route information
nms IMS information
oamcon OAM connecting point
oamend OAM endpoint
PNNI PNNI information
profile PCR,SCR,MBS,EPD configuration
shaper Shaping rate
signaling Signaling connection
tunneling Tunneling information

NTP 279-8013-904
DELETE cevc Function

(Privileged This command is used to delete the connection information for circuit emulation (CE).
Command)
Format
HOSTNAME# DELETE cevc P1 P2
Format Explanation
P1 : Line number (00~33)
P2 : VCI
CE-J2:32~127
CE-DS3:256~287
CE-DS1/E1 Port0:256~287
CE-DS1/E1 Port1:288~319
CE-DS1/E1 Port2:320~351
CE-DS1/E1 Port3:352~383
Output
Circuit emulation connection has been deleted.
NOTE PVCs must be deleted before executing this command.

NTP 279-8013-904
DELETE Function
configserver This command is used to remove a LAN Emulation Configuration Server (LECS)
(Privileged address in the LECS address table.
Command)
Format
HOSTNAME# DELETE configserver P1 P2
Format Explanation
P1 : LECS address table index (0~3)
P2 : ATM address (max. 40char (0~9, a~f, A~F))
Example
Configuration server has been deleted.
NOTE Through Interim Link Management Interface (ILMI), a user may request LECS
addresses from the switch. This table has a maximum of four entries. The user
should use these addresses to locate the LECS for joining into a LAN Emulation
(LANE) server.

NTP 279-8013-904
DELETE dlci Function

(Privileged
This command is used to delete the DLCI data for each line or connection.
Command)
Format
HOSTNAME# DELETE dlci P1 (P2)
Format Explanation
P1: Line Number (00~33)
P2: DLCI Number (16~991)
If only line number is specified, all the DLCI data of the line will be deleted.
NOTE
Output
When DLCI number is not specified:

Line xxx All DLCI interface will be deleted.
1
Are you sure [Y or N]?
If Y is input:
Line xxx DLCI interface has been deleted.
1
If N is input:
Line xxx DLCI interface not deleted.
1
When DLCI number is specified:

Line xxx DLCI interface has been deleted.
1
Output Explanation
1. Line Number

NTP 279-8013-904
DELETE froam Function

(Privileged
This command is used to delete the OAM endpoint of f5 (VC level) between
Command) frame relay and ATM.
Format
HOSTNAME# DELETE froam P1 P2 P3 P4 P5 P6
Format Explanation
P1: Line Number of Point 1 (00~33)
P2: VPI of Point 1 (0~4095)
P3: VCI of Point 1 (32~16383)
P6: VCI of Point 2 (32~16383)
Output
FROAM connection has been deleted.

NTP 279-8013-904
DELETE frprofile Function

(Privileged
This command is used to delete the profile for frame relay.
Command)
Format
HOSTNAME# DELETE frprofile P1
Format Explanation
P1: Name of the profile for frame relay
(Up to 10 alphanumeric letters)
Output
FR profile data has been deleted.

NTP 279-8013-904
DELETE ilmi Function

(Privileged This command is used to delete an ilmi connection.
Command)
Format
HOSTNAME# DELETE ilmi CONNECTION P1 P2
Format Explanation
P2 : VPI (0~4095)
Example
HOSTNAME# Delete ilmi connection 01 0
Output
ILMI connection has been deleted.

NTP 279-8013-904
DELETE iproute Function

(Privileged This command is used to delete IP routing information.
Command)
Format
HOSTNAME# DELETE iproute P1 P2 P3
Format Explanation
P1 : Interface type (atm0 or ec0)
P2 : Destination type (network or host)
P3 : Destination IP address (x.x.x.x (x=0~255) or default (default router IP address)
Example
HOSTNAME# Delete iproute ec0 net 10.1.1.2
Output
IP route information has been deleted.

NTP 279-8013-904
DELETE nms Function

(Privileged This command is used to delete Network Management System (NMS) information.
Command)
Format
HOSTNAME# DELETE nms P1
Format Explanation
P1 : NMS number (0~3)
Example
HOSTNAME# Del nms 1
Output
nms has been deleted.
NOTE To display currently configured NMS IP addresses, use the DISPLAY network
command.

NTP 279-8013-904
DELETE oamcon Function

(Privileged This command is used to delete the connecting point setting of a connection for
Command) transferring an alarm by OAM cell (alarm cell).
Format
(1) HOSTNAME# DELETE oamcon f4 P1 P2 P3 P5 P6
(2) HOSTNAME# DELETE oamcon f5 P1 P2 P3 P4 P5 P6 P7
Format Explanation
P1 : Point type
(segcon or 0 if the switch is a connecting point in the segment flow)
(endcon or 1 if the switch is a connecting point in the end-to-end flow)
P2 : Ingress line number (00~33)
P3 : Ingress Virtual Path Identifier (VPI) (0~4095)
P4 : Ingress Virtual Channel Identifier (VCI) (32~16383)
P5 : Egress line number (00~33)
P6 : Egress VPI (0~4095)
P7 : Egress VCI (32~16383)
NOTE In f4 mode it is not necessary to specify VCI value.
Example (f4)
HOSTNAME# del oamcon f4 seg 00 1 10 2
Example (f5)
HOSTNAME# del oamcon f5 end 00 1 100 10 2 200
Output
OAM connecting point has been deleted.

NTP 279-8013-904
DELETE oamend Function

(Privileged This command is used to delete the endpoint setting of an OAM connection for
Command) transferring an alarm by OAM cell (alarm cell).
Format
HOSTNAME# DELETE oamend P1 P2 P3 P4 {P5}
Format Explanation
P1 : Mode (f4 (Virtual Path (VP) level) or f5 (Virtual Channel (VC) level))
P2 : Point type
(segend or 0 if the switch is an endpoint in the segment flow)
(endend or 1 if the switch is an endpoint in the end-to-end flow) (f4 only)
P4 : VPI (0~4095)
P5 : VCI (32~16383 (defaulted when the mode is f5)
Example (f4)
HOSTNAME# del oamend f4 1 00 1
Example (f5)
HOSTNAME# del oamend f5 0 00 1 100
Output
OAM endpoint has been deleted.

NTP 279-8013-904
DELETE Function
oamf5end
This command is used to delete F5 (VC level) OAM endpoint.
(Privileged
Command) Format
HOSTNAME# DELETE oamf5end P1 P2 P3
Format Explanation
P2: VPI (0~4095)
P5: VCI (32~16383)
Output
OAM f5end endpoint has been deleted.

NTP 279-8013-904
DELETE pnni Function

(Privileged This command is used to delete PNNI information.
Command)
1. To delete the PNNI reachable address:
Format
HOSTNAME# DELETE pnni address
PNNI>P1 P2 P3 P4 P5 P6
This command cancels the PNNI reachable address. After the command is
executed, the PNNI> prompt is shown in the Editor Mode. Type a period (.) to exit
the Editor Mode.
Format Explanation
P1 : Address type (internal or exterior)
P2 : SCOPE (0~104)
P3 : Valid bit length for reachable address
P4 : Reachable address
P6 : VPI (0~4095)
Output
PNNI reachable address has been deleted.
2. To delete the PNNI connection:
Format
HOSTNAME# DELETE pnni connection P1 P2
Format Explanation
P2 : VPI (0~4095)
Output
PNNI connection has been deleted.

NTP 279-8013-904
DELETE profile Function

(Privileged This command is used to delete a policing profile.
Command)
Format
HOSTNAME# DELETE profile P1
Format Explanation
P1 : Profile name
Example
HOSTNAME# del pro my_cbr
Output
Profile data has been deleted.
NOTE If a PVC connection exists that is currently using this profile when this command
is entered, an error message is displayed.

NTP 279-8013-904
DELETE shaper Function

(Privileged This command is used to delete shaping rate.
Command)
Format
HOSTNAME# DELETE shaper P1 P2
Format Explanation
P2 : Shaper number (1~8)
Example
HOSTNAME# del shaper 12 4
Output
Shaping rate has been deleted.
NOTE If a PVC connection using the specified shaper exists when this command is
entered, an error message is displayed.

NTP 279-8013-904
DELETE Function
signaling This command is used to delete a signaling path. This command effectively
(Privileged removes a Switched Virtual Circuit (SVC) signaling connection.
Command)
Format
HOSTNAME# DELETE signaling P1 P2
Format Explanation
P2 : VPI (0~4095)
Example
HOSTNAME# set svcl 13 0 suspend
NOTE To delete the signaling path on an interface, the signaling path svcline must be
suspended.
HOSTNAME# del sig 13 0
Output
Signaling connection has been deleted.

NTP 279-8013-904
DELETE Function
tunneling This command is used to delete a tunneling connection.
(Privileged
Command) Deletion Procedure
1. All connections (PVCs or soft PVPs), if any, must be deleted from the tunneling
VPI that you wish to delete.
2. Use the SET svcline command to suspend the line (and VPI).
3. If signaling connection has been set in the tunneling VPI that you wish to
delete, use the DELETE signaling command to delete the connection.
4. If ILMI connection has been set in the tunneling VPI that you wish to delete,
use the DELETE ilmi command to delete the connection
5. If PNNI connection has been set in the tunneling VPI that you wish to delete,
use the DELETE pnni connection command to delete the connection
6. Enter the DELETE tunneling command.
7. Resume the line by executing the SET svcline command.
Format
HOSTNAME# DELETE tunneling P1 P2
Format Explanation
P2 : VPI (1~4095)

NTP 279-8013-904
Example
HOSTNAME# del sig 30 2
HOSTNAME# del ilmi 30 2
HOSTNAME# del pnni 30 2
HOSTNAME# del tun 30 2
Output
Tunneling information database has been deleted.
NOTE The tunneling connection cannot be deleted if signaling/ILMI/pnni connection

exists on the specified line.

NTP 279-8013-904
DIAGNOSIS ? Function
(Privileged This command is used to display the help message for the DIAGNOSIS command.
Command)
Format
HOSTNAME# DIAGNOSIS ?
Output
all CPU, Switch and Slot diagnosis

cpu CPU diagnosis
slot Slot diagnosis
switch Switch diagnosis

NTP 279-8013-904
DIAGNOSIS all Function

(Privileged This command is used to perform a full diagnosis.
Command) The diagnostic result is reported as an autonomous message. If the diagnostic result
is not good (NG), the detailed possible causes can be viewed by executing the
DISPLAY alarm command.
NOTE Important: All communication is interrupted during diagnosis. This command

should normally be executed when a hardware error is detected or when the system
is initially installed. This testing takes approximately 3 to 5 minutes to complete.
Format
HOSTNAME# DIAGNOSIS all
Output
Diagnosis in progress...

NTP 279-8013-904
DIAGNOSIS cpu Function

(Privileged This command is used to diagnose the CPU board.
Command) The diagnostic result is reported as an autonomous message. If the diagnostic result
is not good (NG), the detailed possible causes can be viewed by executing the

should normally be entered when a hardware error is detected or when the system
Format
HOSTNAME# DIAGNOSIS cpu
Output

NTP 279-8013-904
DIAGNOSIS slot Function

(Privileged This command is used to diagnose installed line packages.
Command) The diagnostic result is reported as a restart message during startup after
diagnosis. If the diagnostic result is not good (NG), the detailed possible causes
can be viewed by executing the DISPLAY alarm command.
Format
HOSTNAME# DIAGNOSIS slot {P1}
Format Explanation
P1 : Slot number (00-33)
Output
If Y is entered in response to confirmation message:
Are you sure? [Y or N] y
NOTE This command should normally be used when when setting up the system for the
first time, or when a hardware failure is detected.

NTP 279-8013-904
DIAGNOSIS Function
switch This command is used to diagnose the switch board.
(Privileged The diagnostic result is reported as an autonomous message. If the diagnostic result
Command) is not good (NG), the detailed possible causes can be viewed by executing the

should normally be entered when a hardware error is detected or when the system
Format
HOSTNAME# DIAGNOSIS switch
Output

NTP 279-8013-904
DISPLAY ? Function
(General This command is used to display the help message for the DISPLAY command.
Command)
NOTE DISPLAY ? and SHOW ? serve the same purpose.
Format
HOSTNAME> DISPLAY ?

NTP 279-8013-904
Output
alarm All alarms

all All configuration data
atmsig Q.2931 parameters
boot Boot parameters
calledsoftpvp Called softpvp check flag
cdvt CDVT configuration
cevc Circuit emulation configuration data
clock Clock mode
configuration All configuration data
dynamicroute Dynamic route information
ether IP address of Ethernet interface
iisp Crankback information
interface Line interface parameters
line Line interface status
looptime Looptime switch
mac LAN card MAC address
network Network configuration data
oamend OAM endpoint
pnni PNNI information
pvc PVC information
redundancy Redundancy of card's CPUs
route SVC static routing table
scope Scope information
scroll Scroll lines
server Server IP address
shaper Shaping rate
softpvp Soft PVPC/PVCC
sscop SSCOP parameters
status Hardware operating status
svc SVC connection
svcline SVC line status of the line interface
T309trg T309 when interface failure has occured
telnetlimit Telnet session timeout
time System time
traffic Traffic & Performance value
version Boot/Software Version

NTP 279-8013-904
DISPLAY alarm Function

(General Displays the latest information on errors in progress. Displays each error by failed
Command) area. (This command will not display information on properly functioning areas.)
Format
HOSTNAME> DISPLAY alarm
Output
Hardware Alarm
**.**.** **:**:** - ************ ************ ********
1 2 3 4
Output Explanation
1. Date and time of failure (year.month.day hour:minute:second)
2. Failed part
Environment
FAN <side number>
Power Unit <side number>
CPU
Switch
Line Board <slot number>
Line Buffer <slot number>
Line Card <slot number> : <Line Card Type>
3. Alarm type
Control Alarm : Indicates a control error.
Clock Alarm : Indicates a clock error.
Path Alarm : Indicates a path error.
Diagnosis NG : Indicates diagnosis NG.
4. Alarm ID
Refer to Hardware Alarms table.

NTP 279-8013-904
Example
Hardware Alarm
96.03.10 20:11:48 - Environment000001
96.03.12 12:33:21 - FAN 0
96.02.22 08:47:38 - FAN 1
96.02.07 15:56:08 - Power Unit 0
96.02.08 12:36:15 - CPUDiagnosis NG070002
96.10.13 21:02:40 - SwitchClock Alarm010002
96.03.24 05:32:20 - Line Board 0 Buffer 2Clock Alarm000001
96.02.17 18:36:28 - Line Buffer 1 Control Alarm010001
96.07.18 02:03:49 - Line Card 2 OC3c/STM-1(MMF)Path Alarm010001
Hardware Alarms
Alarm Alarm number

<Shell error>
POWER alarm - -
FAN alarm - -
<Environment error>
Abnormal rise in environmental temperature - 000001
<Switch/CPU card error>
Cell alignment signal error Path Alarm 020002
BMT parity error Path Alarm 020003
SC diagnosis NG Path Alarm 020004
Regression enable match error Path Alarm 030001
Regression clear match error Path Alarm 030002
BF0 parity error Path Alarm 030003
BF diagnosis NG Path Alarm 030004
BF1 parity error Path Alarm 030103
ES0 Up side sync error Path Alarm 040001
ES0 Down side sync error Path Alarm 040002
ES0 port A FIFO overflow Path Alarm 040004
ES0 port B FIFO overflow Path Alarm 040006
ES0 diagnosis NG Path Alarm 040007
ES1 Up side sync error Path Alarm 040101
ES1 Down side sync error Path Alarm 040102
ES1 port A FIFO overflow Path Alarm 040104

NTP 279-8013-904
Alarm Alarm number

ES1 port B FIFO overflow Path Alarm 040106
ES1 diagnosis NG Path Alarm 040107
SAR register NG Diagnosis NG 050005
Header conversion table parity error Path Alarm 060004
<Switch/CPU card error>
DI diagnosis NG Diagnosis NG 610010
Memory diagnosis NG Diagnosis NG 070002
<Line buffer error>
Received cell parity error Path Alarm 040001
RIRO SGRAM test error Control Alarm 040002
HT SGRAM test error Control Alarm 040003
RIRO SRAM test error Control Alarm 040004
Illegal interruption Control Alarm 040005
Illegal cell transmission error Control Alarm 040007
IBC diagnosis NG Diagnosis NG 040008
IBC RIRO SGRAM diagnosis NG Diagnosis NG 040009
IBC HT SGRAM diagnosis NG Diagnosis NG 040010
IBC RIRO SRAM diagnosis NG Diagnosis NG 040011
OBC diagnosis NG Diagnosis NG 040012
OBC Cell Buff diagnosis NG Diagnosis NG 040013
OBC HTM diagnosis NG Diagnosis NG 040014
OBC BCT/BMT diagnosis NG Diagnosis NG 040015
<Line card error>
OC-3c/STM-1
PHY0 reception FIFO overflow Path Alarm 010001
PHY0 diagnosis NG Diagnosis NG 010002
PHY (OC3C-SMF-L) diagnosis NG Diagnosis NG 010002
UTOPIA parity error Path Alarm 020001

NTP 279-8013-904
Alarm Alarm number

50 MHz clock interruption Clock Alarm 020002
MUX diagnosis NG Diagnosis NG 020012
OC-12c/STM-4
UTOPIA parity error Path Alarm 030001
CU2INF diagnosis NG Diagnosis NG 030002
Transmission clock interruption Clock Alarm 040001
SFIT4 FIFO error Path Alarm 040002
UNIC diagnosis NG Diagnosis NG 040003
UCFAD reception FIFO overflow Path Alarm 050001
UCFAD transmission FIFO overflow Path Alarm 050002
CFAD diagnosis NG Diagnosis NG 050003
Reception clock interruption Clock Alarm 070002
System clock interruption Clock Alarm 070003
FPGA diagnosis NG Diagnosis NG 070004
reception FIFO underrun Path Alarm 120001
reception FIFO overrun Path Alarm 120002
transmission parity error Path Alarm 120003
S/UNI diagnosis NG Path Alarm 120004
TAXI
UTOPIA level 2 parity error Path Alarm 020001
12.5 MHz clock interruption Clock Alarm 020003
Input 8 MHz clock interruption Clock Alarm 020004
TAC0 diagnosis NG Diagnosis NG 130002
6.3M
TX UTOPIA level 2 parity error Path Alarm 020001
TX UTOPIA level 2 operation clock interrupted Clock Alarm 020002
Transmission clock interrupted Clock Alarm 020005
PLO transmission clock interrupted Clock Alarm 020006

NTP 279-8013-904
Alarm Alarm number

LCA Common diagnosis NG Diagnosis NG 150001
LCA Separate diagnosis NG Diagnosis NG 150002
UCFAD2 diagnosis NG Diagnosis NG 160001
DS3/E3
UTOPIA level 1 parity error #0 Path Alarm 020007
Input 8 KHz clock interruption Clock Alarm 060001
PLD diagnosis NG Diagnosis NG 060003
FRAMER#0 reception FIFO underflow Path Alarm 080001
FRAMER#0 reception FIFO overflow Path Alarm 080002
FRAMER#0 transmission FIFO overflow Path Alarm 080003
FRAM0 diagnosis NG Diagnosis NG 080004
FRAM1 diagnosis NG Diagnosis NG 080104
PR-1.5M
Transmission clock interrupted Clock Alarm 020005
PLO transmission clock interrupted Clock Alarm 020006
LCA diagnosis NG Diagnosis NG 150001
Frame aligner parity error Path Alarm 150003
UCFAD2 diagnosis NG Diagnosis NG 160001
DS1/E1

NTP 279-8013-904
Alarm Alarm number

8 KHz clock interruption Clock Alarm 060001
16 KHz oscillator clock interruption Clock Alarm 060002
PLD diagnosis NG Diagnosis NG 060003
12 KHz oscillator clock interruption Clock Alarm 060004
FRAMER#0 UTOPIA level 1 Down side Path Alarm 140004
FRAMER#0 (PM7345) diagnosis NG Diagnosis NG 140005
FRAMER#2 (PM7345) diagnosis NG Path Alarm 140205
FRAMER#0 (PM4341A) diagnosis NG Diagnosis NG 170001

NTP 279-8013-904
Alarm Alarm number

Server Card
WDT overflow Control Alarm 090001
CPU clock disconnected Clock Alarm 090002
PCI bus clock disconnected Clock Alarm 090003
PCI bus parity error Control Alarm 090004
RICE401 memory parity error Control Alarm 090005
FR-Buffer SDRAM diagnosis NG Diagnosis NG 090006
PCI bus clock disconnected Clock Alarm 100001
PCI SERR Control Alarm 100002
SW50M clock disconnected Clock Alarm 100003
MemOut Control Alarm 100004
DMAOut Control Alarm 100005
SSCOP link interrupted among cards Control Alarm 110003
CE-DS1
UTOPIA level2 parity error Path Alarm 020001
50MHz clock interrupted Clock Alarm 020002
19MHz clock interrupted Clock Alarm 020011
FRAMER #0 (PM4341A) diagnosis NG Diagnosis NG 170001
1.544M clock generated in PKG interrupted Clock Alarm 210001
38.8M clock generated in PKG interrupted Clock Alarm 210002
FPGA diagnosis NG Diagnosis NG 210003
IGT SAR diagnosis NG Diagnosis NG 240001
FR-DS1
WDT overflow Control Alarm 090001
CPU clock interrupted Clock Alarm 090002

NTP 279-8013-904
Alarm Alarm number

PCI BUS clock interrupted Clock Alarm 090003
PCI BUS parity error Control Alarm 090004
RICE401 mamory parity error Control Alarm 090005
FR-Buffer SDRAM diagnosis NG Control Alarm 090006
Server Card / FR-DS1
CPU DRAM on card side diagnosis NG Diagnosis NG 250001
CPU on card side diagnosis timeout Diagnosis NG 250002

NTP 279-8013-904
DISPLAY all Function

(General This command is used to display all the information registered in the configuration
Command) data.
Format
HOSTNAME> DISPLAY all
Output
Same as output for DISPLAY ? command.
NOTE Information for a line that is in Admin Down status cannot be displayed.

NTP 279-8013-904
DISPLAY atmsig Function

(General This command is used to display Q.2931 parameters.
Command)
Format
HOSTNAME> DISPLAY atmsig
Example
HOSTNAME# display atmsig

Line VPI U/N 301 303 308 309 310 313 316 317 322 397 398 399 UNIver
00 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
01 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
02 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
03 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
10 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
11 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
12 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
13 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
20 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
21 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
22 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
23 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
30 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
31 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
32 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
33 0 Network 180 4 30 10 10 4 120 60 4 180 4 14 4.0( - )
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
NOTE Timer designation may be found in the User Network Interface (UNI)
specifications of the ATM Forum.
Output Explanation
1. Line number (00~33)
2. VPI
3. IISP user side "User" or IISP network side "Network"
4. T301 timer value
5. T303 timer value
6. T308 timer value
7. T309 timer value
8. T310 timer value
9. T313 timer value

NTP 279-8013-904
10. T316 timer value

16. UNI Version in the configuration data
17. UNI Version under operation (may be different than configured version if
reported differently through ILMI)

NTP 279-8013-904
DISPLAY boot Function

(General This command is used to display the firmware boot source for the next restart. After
Command) restart, the boot mode will default back to the flash mode.
Format
HOSTNAME> DISPLAY boot
Output
-FLASH mode
Online program stored in the flash memory will be loaded after

reset.
-FLASH_UP mode
Online program stored in the PCMCIA#0 flash memory will be loaded

after reset.Configuration data will be loaded from the PCMCIA#1
flash memory.Configuration data will not be stored to the PCMCIA#0
flash memory.
-FLASH_UP SAVE mode
Online program stored in the PCMCIA#0 flash memory will be loaded

after reset.Configuration data will be loaded from the PCMCIA#1
flash memory.Configuration data will be stored to the PCMCIA#0
flash memory.
-INITIALIZE mode
Online program stored in the workstation will be loaded after re-

set.Configuration data will be initialized.Online program and con-
figuration data will not be stored to the flash memory.
-INITIALIZE_SAVE mode

set.Configuration data will be initialized.Online program and con-
figuration data will be stored to the flash memory.

NTP 279-8013-904
-NETWORK mode

set.Configuration data will be loaded from the flash memory. On-
line program and configuration data will not be stored to the flash
memory.
-NETWORK_SAVE mode

set.Configuration data will be loaded from the flash memory.Online
program and configuration data will be stored to the flash memory.

NTP 279-8013-904
DISPLAY Function
calledsoftpvp This command is used to display the recognition standard of calledsoftpvp.
(General
Command) Format
HOSTNAME> DISPLAY calledsoftpvp
Output
Called softpvp check flag:off

1
Output Explanation
1. Flag (ON (enable), OFF (disable))

NTP 279-8013-904
DISPLAY cdvt Function

(General This command is used to display the Cell Delay Variation Tolerance (CDVT) data
Command) the system currently manages.
Format
HOSTNAME> DISPLAY cdvt
Example
HOSTNAME# display cdvt

PCR CDVT SCR CDVT
-----------------------+-----------------------------
Line VPI CBR rtVBR nrtVBR UBR UPC-Mode2 UPC-mode3 UPC-mode4
00 - 2000 2000 2000 2000 2000 2000 2000
01 - 2000 2000 2000 2000 2000 2000 2000
02 - 2000 2000 2000 2000 2000 2000 2000
03 - 2000 2000 2000 2000 2000 2000 2000
10 - 2000 2000 2000 2000 2000 2000 2000
11 - 2000 2000 2000 2000 2000 2000 2000
12 - 2000 2000 2000 2000 2000 2000 2000
13 - 2000 2000 2000 2000 2000 2000 2000
20 - 2000 2000 2000 2000 2000 2000 2000
21 - 2000 2000 2000 2000 2000 2000 2000
22 - 2000 2000 2000 2000 2000 2000 2000
23 - 2000 2000 2000 2000 2000 2000 2000
30 - 2000 2000 2000 2000 2000 2000 2000
31 - 2000 2000 2000 2000 2000 2000 2000
32 - 2000 2000 2000 2000 2000 2000 2000
33 - 2000 2000 2000 2000 2000 2000 2000
NOTE Cell delay variation is dependent on cell transfer rate.

NTP 279-8013-904
DISPLAY cevc Function

(General This command is used to display Circuit Emulation (CE) connection information.
Command)
Format
HOSTNAME> DISPLAY cevc P1 {P2}
Format Explanation
P2 : VCI
CE-DS1/E1 Port0 : 256~287
CE-DS1/E1 Port1 : 288~319
CE-DS1/E1 Port2 : 320~351
CE-DS1/E1 Port3 : 352~383
Output
When VCI is defaulted:
Line: xx 1
VCI Direction Number of Timeslot
Up/Down
xxx xxxx xx/xx
2 3 4
Output Explanation
2. VCI
3. Direction (bi, up (STM->ATM), down (ATM->STM))
4. Number of timeslot

NTP 279-8013-904
When VCI is specified:
Line: xxx VCI: xxx Direction:xxxx

1 2 3
Condition data: xxx 4
-------------------------------------------------------------------------------
up Partial Fill Size:xxx 5
PCR : xxxxx(cell/sec)6
Number of Timeslot:xx 7
Timeslot : x x xx xx xx xx xx8
-------------------------------------------------------------------------------
down Partial Fill Size:xxx
CDVT : xxxxxx 9
PCR : xxxxx(cell/sec)
Channel Status: xxxxxx 10
Number of Timeslot:xx
Timeslot : x x xx xx xx xx xx
Output Explanation
2. Virtual Channel Identifier (VCI)
3. Direction (bi, up, down)
4. Condition data. IDLE cell pattern of CE
5. Partial Fill Size
6. Peak Cell Rate (PCR)
7. Number of Timeslot
8. Timeslot
9. Value of Cell Delay Variation Tolerance (CDVT)
10. Channel Status (Normal, Sequence Error, Pointer Mismatch, Pointer
Parity Error, FIFO overflow, FIFO underflow)
NOTE In case of a single direction (either up or down), only information for up or down
will be displayed. In case of bi-direction, information for both up and down
directions will be displayed. With this software, Channel Associated Signaling
(CAS)/Basic is fixed to Basic.

NTP 279-8013-904
DISPLAY clock Function

(General This command is used to display the current clocking source mode.
Command)
Format
HOSTNAME> DISPLAY clock
Example
If the "master" system clock mode is selected:
Clocking mode: Master
If the "slave" system clock mode is selected and the slave lines are registered:
Clocking mode:Slave
SlavelineStatus
*030Good
031Good
032Failure
033Failure
If the "slave" system clock mode is selected:
Clocking mode: Slave

Slave line Status\
** ****
1 2
NOTE Output format for slave mode. Output format is not needed for master mode.
Output Explanation
The current clock sampling line (slave clock mode) is identified by an asterisk
(*) at the left of the line number.
2. Line status (GOOD, Failure, AdminDown, Not Installed, Not supported or
Diagnostics, Inaccurate, Frequency out of range, Loss of 8K clock or Loss of
64K clock)
NOTE Slave lines do not include 100M-TAXI lines. If, after a line package has been
removed, another line package of different type is inserted, and no slave line is
available, that line will be indicated as "Not installed."

NTP 279-8013-904
DISPLAY Function
configserver This command is used to display the LECS ATM address table. These addresses
(General may be retrieved, through ILMI, by an end-user. In turn, the end-user may use these
Command) addresses to connect to the LECS.
Format
HOSTNAME> DISPLAY configserver {P1}
Format Explanation
P1 : LECS address table index (00~33) (optional)
NOTE All entries will be shown unless a specific index {P1} is given.
Example
INDEX Configuration server

* *.**********.****.********
1 2
0 47.000000000000000000000000.00A145711144.00
Output Explanation
1. Index
2. ATM address

NTP 279-8013-904
DISPLAY Function
configuration This command is used to display the entire configuration data of the switch.
(General
Command) Format
HOSTNAME> DISPLAY configuration

NTP 279-8013-904
DISPLAY dlci Function

(General
This command is used to display the DLCI set information of the specified line.
Command)
1. Display DLCI set information
Format
HOSTNAME> DISPLAY dlci configuration P1
Format Explanation
Output
LINE : xx Interworking : xxxxxxx

1 2
DLCI VPI VCI FR-Profilename PCR SCR MBS PVC
xxx xxx xxx xxxxxxxxxx xxxx xxxx xxxx xxxx
3 4 5 6 7 8 9 10
Output Explanation
1. Line Number
2. Interworking type
3. DLCI Number
4. VPI
5. VCI
6. Profile name for frame relay
7. PCR
8. SCR
9. MBS
10. Set PVC set / not set (exist / -)

NTP 279-8013-904
2. Display frame relay PVC status confirmation procedure/OAM setting
Format
HOSTNAME> DISPLAY dlci status P1 (P2) (P3)
Format Explanation
P2: Display start DLCI Number (16 - 991; 16 is default)
P3: Displayed data count (1-120; 120 is default)
Output
Line: xxx1
DLCI Status OAM
xxx xxxxxx xxx
(xxx xxxxxx xxx)
2 3 4
Output Explanation
1. Line Number
2. DLCI Number
3. Status (Active, Inactive)
4. OAM setting (on, off)

NTP 279-8013-904
DISPLAY Function
dynamicroute This command is used to display the information registered in the dynamic routing
(General table. Through ILMI, a user registers an ATM address and associated port with the
Command) switch. Upon successful ILMI address registration, the information may be
displayed with this command. Also, LANE server routing addresses are stored in
this table.
Format
HOSTNAME> DISPLAY dynamicroute {P1}
Format Explanation
NOTE All registered addresses will be shown, unless a specific port {P1} is designated.
Then only information pertaining to the chosen port is shown.
Output
Destination Type Line VPI HopCount

*.************.******.* **** *** *** *******
1 2 3 4 5
47.000000000000000000000000.123456781012.00 NSAP 01 - 1
NOTE Two digits designate one byte.
Output Explanation
1. End user ATM address (switch prefix + ESI + SEL)
2. ATM address type (NSAP or E.164)
3. Line number associated with address
4. Tunneling VPI value or -
5. Hop count if tunneling; displays the number of tunneled switches.
NOTE If the server address has been registered from the server card, the slot number of
the server card will be displayed as the line number. In addition, the following
server type will be displayed as the VPI:
VPI : Server type
66: LECS
67: LECS
68: BUS

NTP 279-8013-904
DISPLAY ether Function

(General This command is used to display IP address and mask value of the Ethernet port.
Command) The Ethernet port is used for download of system software, Telnet sections for MAT
commands, and a NMS link.
Format
HOSTNAME> DISPLAY ether
Output
IP address/mask of Ethernet interface:***.***.***.***, ***.***.***.***

1 2
153.208.205.115,255.255.255.0
Output Explanation
1. Ethernet IP address
2. Mask value of Ethernet

NTP 279-8013-904
DISPLAY froam Function

(General This command is used to display the OAM endpoint of f5 (VC level) between frame
Command) relay and ATM.
Format
HOSTNAME> DISPLAY froam
Output
Line VPI/VCI Line VPI/VCI status

xxx xxx/xxx xxx xxx/xxx xxxxxx
xxx xxx/xxx xxx xxx/xxx xxxxxx
1 2 3 4 5 6 7
Output Explanation
1. Line Number of Point 1 (00~33)
2. VPI of Point 1 (0~4095)
3. VCI of Point 1 (32~16383)
4. Line Number of Point 2 (00~33)
5. VPI of Point 2 (0~4095)
6. VCI of Point 2 (32~16383)
7. Status (Normal, Failure, AIS, RDI)

NTP 279-8013-904
DISPLAY frprofile Function

(General This command is used to display the set information of profile for frame relay.
Command)
Format
HOSTNAME> DISPLAY frprofile (P1)
Format Explanation
P1: Name of the profile for frame relay
If a profile name is specified, only the data related to this profile name is
NOTE
displayed. If not, all profiles are displayed.
Output
If the profile name is not specified:
FR-Profilename Interworking type [kbps]

xxxxxxxxxx xxxxxxx xxx
xxxxxxxxxx xxxxxxx xxx
1 2 3
Output Explanation
1. Frame relay profile name
2. Interworking type (Network, Service)
3. CIR value (1~1984)

NTP 279-8013-904
If the profile name is specified:
FR-Profilename: xxxxxxxxxx 1
Interworking Type: xxxxxxx 2
CIR [kbps]: xxxx 3
DE to CLP mapping mode: xxxxx 4
CLP value: x 5
CLP to DE mapping mode: xxxxx 6
DE value: x 7
Protocol encapsulation mode: xxxxxxxxxxx 8
Congestion indication mode: xxxxx 9
Output Explanation
1. Frame relay profile name
3. CIR value (1~1984)
4. Cell loss priority mode (Mode1, Mode2)
5. Set CIR value (0/1)
6. Frame discard priority mode (Mode1, Mode2)
7. Set DE value (0/1)
8. Encapsulation mode (Transparent, Translation)
9. Forward congestion (FECN) mode (Mode1, Mode2)

NTP 279-8013-904
DISPLAY Function
frversion
This command is used to display the version of software and boot ROM of the
(General frame relay card CPU in the specified slot.
Command)
Format
HOSTNAME> DISPLAY frversion P1
Format Explanation
P1: Slot Number (0~3)
Output
Slot: xx 1
Frame relay software version: xxxxxxx 2
Frame relay boot ROM version: xxxxxxx 3
Output Explanation
1. Slot Number
2. Frame relay software version
3. Frame relay Boot ROM version

NTP 279-8013-904
DISPLAY iisp Function

(General This command is used to display the status of the three different IISP mode types
Command) the system currently manages.
Format
HOSTNAME DISPLAY iisp P1
Format Explanation
P1: Mode type (loopcheck, splithorizon, or swaproute)
"Loopcheck" displays a setup loop protection.
"Splithorizon" displays status whether or not to allow a call forwarding to the
signaling connection which has received a setup message.
"Swaproute" displays an operation status of the simulated crank back.
Output
If P1 is loopcheck:
******* 1
Hopcount:** 2
If P1 is splithorizon:
Line VPI Splithorizon

** **** *******
3 4 5
If P1 is swaproute:
******* 6
Timer[min]:** 7
NOTE See SET IISP for mode type explanation.

NTP 279-8013-904
Output Explanation
1. Status (disabled or enabled)
2. Hop count (not displayed in disabled status)
4. VPI
7. Resume timer value (not displayed in disabled status)

NTP 279-8013-904
DISPLAY ilmi Function

(General This command is used to display the ILMI path and parameters the system currently
Command) uses.
Format
HOSTNAME> DISPLAY ilmi P1{P2}
Connection {P1} Control connection
Configuration {P1} Auto configuration
Neighbor {P1} Neighbor information
Discovery {P1} Auto discovery information
Process {P1} Process flag information
Format Explanation
P1: One of connection, configuration, etc.
P2: Line number (00~33) (optional)
NOTE If a line number {P1} is specified, only the data related to this line number is
displayed. If not, all lines are displayed.

NTP 279-8013-904
Output
HOSTNAME# display ilmi ?

connection Control connection
configuration Auto configuration
neighbor Neighbor information
discovery Auto discovery information
process Process flag information
HOSTNAME# display ilmi connection ?

xy x:Slot number, y:Port number (0 <= x <= 3, 0 <= y <= 3)
<cr>
HOSTNAME# display ilmi connection 00 ?

<cr>
HOSTNAME# display ilmi connection 00

Line VPI/VCI Timeout Retry Keepalive
00 0/16 1 4 5
HOSTNAME# display ilmi connection

Line VPI/VCI Timeout Retry Keepalive
00 0/16 1 4 5
01 0/16 1 4 5
02 0/16 1 4 5
03 0/16 1 4 5
10 0/16 1 4 5
11 0/16 1 4 5
12 0/16 1 4 5
13 0/16 1 4 5
20 0/16 1 4 5
21 0/16 1 4 5
22 0/16 1 4 5
23 0/16 1 4 5
HOSTNAME# dis ilmi configuration ?

<cr>
HOSTNAME# dis ilmi configuration 00 ?

<cr>
HOSTNAME# dis ilmi configuration 00

Line VPI/VCI Valid VPI/VCI Interface UNIver PNNIver IME
00 0/16 - / - - - - -

NTP 279-8013-904
HOSTNAME# dis ilmi configuration

Line VPI/VCI Valid VPI/VCI Interface UNIver PNNIver IME
00 0/16 - / - - - - -
01 0/16 - / - - - - -
02 0/16 - / - - - - -
03 0/16 - / - - - - -
10 0/16 - / - - - - -
11 0/16 - / - - - - -
12 0/16 - / - - - - -
13 0/16 - / - - - - -
20 0/16 - / - - - - -
21 0/16 - / - - - - -
22 0/16 - / - - - - -
23 0/16 - / - - - - -
HOSTNAME# display ilmi neighbor ?

<cr>
HOSTNAME# display ilmi neighbor 00 ?

<cr>
HOSTNAME# display ilmi neighbor 00

Line VPI/VCI Valid VPI/VCI Interface UNIver PNNIver
00 0/16 - / - - - -
HOSTNAME# display ilmi neighbor

Line VPI/VCI Valid VPI/VCI Interface UNIver PNNIver
00 0/16 - / - - - -
01 0/16 - / - - - -
02 0/16 - / - - - -
03 0/16 - / - - - -
10 0/16 - / - - - -
11 0/16 - / - - - -
12 0/16 - / - - - -
13 0/16 - / - - - -
20 0/16 - / - - - -
21 0/16 - / - - - -
22 0/16 - / - - - -
23 0/16 - / - - - -
HOSTNAME# display ilmi discovery ?

<cr>
HOSTNAME# display ilmi discovery 00 ?

<cr>
HOSTNAME# display ilmi discovery 00

Line VPI/VCI IP address IfName
00 0/16 - -

NTP 279-8013-904
HOSTNAME# display ilmi discovery

Line VPI/VCI IP address IfName
00 0/16 - -
01 0/16 - -
02 0/16 - -
03 0/16 - -
10 0/16 - -
11 0/16 - -
12 0/16 - -
13 0/16 - -
20 0/16 - -
21 0/16 - -
22 0/16 - -
23 0/16 - -
HOSTNAME# display ilmi process ?

<cr>
HOSTNAME# display ilmi process 00 ?

<cr>
HOSTNAME# display ilmi process 00

Line VPI/VCI Flag MIB
00 0/16 OFF -
HOSTNAME# display ilmi process

Line VPI/VCI Flag MIB
00 0/16 OFF -
01 0/16 OFF -
02 0/16 OFF -
03 0/16 OFF -
10 0/16 OFF -
11 0/16 OFF -
12 0/16 OFF -
13 0/16 OFF -
20 0/16 OFF -
21 0/16 OFF -
22 0/16 OFF -
23 0/16 OFF -

NTP 279-8013-904
DISPLAY Function
interface This command is used to display line interface information.
(General
Command) Format
HOSTNAME> DISPLAY interface {P1}
Format Explanation
P1 : Line number (00~33) (optional)
NOTE If a line number {P1} is specified, only the data related to this line number is
displayed. If not, all information for all data lines is displayed.
Example
If P1 is not specified:
Line ** 1
Interface ******** 2
Physical Layer ********** 3
Forum/ITU ******** 4
Unassigned/Idle ************ 5
Valid VPI/CPI **/** 6

NTP 279-8013-904
Output Explanation
1. Line number
2. Interface type (in the case of other than CE or FR, pri_uni, pri-nni,
pub_uni; in the case of FR, UNI, NNI; in the case of CE, - is displayed)
pri_uni
pri_nni
pub_nni
3. Physical layer type
4. ATM Forum/ITU/TTC/ITU-T/FR-Forum/ANSI (in the case of CE, - is
displayed)
5. Unassigned Cell/Idle Cell (in the case of CE, - is displayed)
6. Valid VPI/ VCI bit counts
If P1 is specified, in case of OC-3c, OC-12c, STS-3c/STM1(COAXIAL) and

100M-TAXI:
Line: xxx 1
Interface type: xxxxxxxxx 2
Physical layer: xxxxxxx 3
Forum/ITU: xxxxx 4
Unassigned/Idle: xxxxxxxxx 5
Valid VPI: xx 6
Valid VCI: xx 7
Filter mask VPI: xx 8
Filter mask VCI: xx 9
Output Explanation
1. Line number
2. Interface type (pri_uni, pri_nni, pub_uni)
4. ATM Forum/ITU
5. Unassigned Cell / Idle Cell
6. Valid VPI bit counts
7. Valid VCI bit counts
8. VPI filter mask value
9. VCI filter mask value

NTP 279-8013-904
If P1 is specified, in case of DS3:
Line: xx 1
Forum/ITU: xxxxx 4
Unassigned/Idle: xxxxxxx 5
Valid VPI: xx 6
Valid VCI: xx 7
Cell mapping mode: xxxx 10
Scramble: xx 11
LBO: xx 12
Frame mode: xxxx 13
Output Explanation
1. Line number
4. ATM Forum (fixed)
10. Cell mapping (PLCP, Direct)
11. Scramble (OFF, ON)
12. Line Build Out (Lo or Hi)
13. Frame mode (C-bit, M23)

NTP 279-8013-904
If P1 is specified, in case of E3:
Line: xx 1
Physical layer: E3 3
Forum/ITU: xxxxx 4
Valid VPI: xx 6
Valid VCI: xx 7
Scramble: xx 11
Frame mode: xxxx 12
Output Explanation
1. Line number
4. ITU (fixed)
12. Frame mode Frame (G382, G804, G751)

NTP 279-8013-904
If P1 is specified, in case of DS1, E1:
Line: xx 1
Forum/ITU: xxxxx 4
Valid VPI: xx 6
Valid VCI: xx 7
Scramble: xx 11
LBO: xx 12
Output Explanation
1. Line number
4. ITU (fixed)
12. Line Build Out (DS1 only)

NTP 279-8013-904
If P1 is specified, in case of J2:
Line: xx 1
Forum/ITU: xxxxx 4
Valid VPI: xx 6
Valid VCI: xx 7
Line rate: xxxx 10
Output Explanation
1. Line number
4. ITU (fixed)
10. Line rate

NTP 279-8013-904
If P1 is specified (Primary):
Line: xx 1
Forum/ITU: xxxxx 4
Valid VPI: xx 6
Valid VCI: xx 7
Line rate: xxxx 10
Output Explanation
1. Line number
4. TTC/ITU-T
10. Line rate

NTP 279-8013-904
If P1 is specified, in case of CE-DS1:
Line: xx 1
Interface type: xxxxxxxxxx 2
Physical layer: xxxxxxxxx 3
Forum/ITU: xxxxx 4
Valid VPI: xx 6
Valid VCI: xx 7
Service: xxxxxxxxx 8
LBO: xx 9
Frame mode: xxx 10
CAS mode: xxxx 11
Output Explanation
1. Line number
2. Interface type (pri_uni, pri_nni, pub_uni) (not displayed)
4. ATM Forum (fixed) (not displayed)
5. Unassigned Cell / Idle Cell (not displayed)
7. Valie VCI bit counts
8. Service mode (Structured/Unstructured)
9. Line Build Out
10. Frame mode (ESF/SF)
11. CAS mode (CAS/Basic in the case of Structured; - in the case of
Unstructured)

NTP 279-8013-904
If P1 is specified, in case of FR-DS1:
Line: xxx 1
Interface type: xxx 2
Physical layer: FR-DS1 3
Forum/ITU/ANSI: xxxx 4
Interworking: xxxxxxx 5
LBO: xxxxxxx 6
Fractional type: xxxxxxxxx 7
Fractional set: xx xx xx xx 8
Output Explanation
1. Line number
2. Interface (UNI, NNI)
4. FR-Forum/ITU_T/ANSI
6. Line Build Out (0-110, 110-220, 220-330, 330-440, 440-550, 550-660)
7. Fractional type (Unchannelized, Fractional)
8. Fractional setting (-, if fractional type is unchannelized)

NTP 279-8013-904
DISPLAY iproute Function

(General This command is used to display IP routing information the system currently uses.
Command)
Format
HOSTNAME> DISPLAY iproute {P1} {P2} {P3}
Format Explanation
P1 : Interface type (atm0 or ec0) (optional)
P2 : Destination type (net or host) (optional)
P3 : Destination on IP address (x.x.x.x (x=0~255)) or default (optional).
Example
NOTE All routes will be shown unless information is requested for a particular P1, P2, or
P3.
Type Destination Gateway Interface Line VPI/VCI

*** ***.***.***.*** ***.***.***.*** *** ** ***/***
1 2 3 4 5 6
net default 10.1.1.10 ec0 -1-
Output Explanation
1. Destination type
2. Destination IP address
3. Gateway IP address
4. Interface type
6. VPI/VCI

NTP 279-8013-904
DISPLAY line Function

(General This command is used to display physical line status.
Command)
NOTE No information will be displayed for uninstalled lines and lines whose installation
cannot be recognized due to an error, etc.
Format
HOSTNAME> DISPLAY line
Output
Line Line status Hardware status Loop back

** ****************** ***** *****
1 2 3 4
Output Explanation
2. Line error
Admin down This port has been put out of service by
SET linestatus command.
AIS Alarm Indication Signal (AIS) received.
AIS path Path layer AIS received.
AIS section Section layer AIS received.
Good Functioning properly.
Idle IDLE signal received.
Initializing Initialization is in progress.
Loss of cell delineation Cell is out of sync.
Loss of frame Frame is out of sync.
Loss of pointer STS frame pointer error.
Loss of signal Signal interruption occurred.
Payload All One Payload in transmission frame is all 1
(main signal all 1).
PLCP loss of frame Physical Layer Convergence Protocol
(PLCP) layer frame is out of sync.
PLCP out of frame PLCP layer frame end cannot be detected.
PLCP yellow PLCP layer yellow signal received.

NTP 279-8013-904
RDI Yellow alarm signal received.

Red alarm Red alarm signal received.
Remote Alarm Indication Remote alarm received.
Yellow path Path layer remote alarm received.
Yellow section Section layer remote alarm received.
3. Line card status
Normal
Failure
Diagnosis
Diagnosis NG
Initializing
4. Loopback status ("Normal" if not set)
Normal
local
remote

NTP 279-8013-904
DISPLAY Function
looptime This command is used to display whether the per-port clocking recovery mode has
(General been set (for active lines only). By default, all lines use the switch clock source
Command) (whether slave or master).
Format
HOSTNAME> DISPLAY looptime
Output
Line **: ***

1 2
Line 012:On
Output Explanation
2. Loop time setting status
on: Loop time is on
off: Loop time is off
-: Package type is illegal.

NTP 279-8013-904
DISPLAY mac Function

(General This command is used to display the Personal Computer Memory Card
Command) International Association (PCMCIA) Local Area Network (LAN) card Moves,
Adds, and Changes (MAC) address.
Format
HOSTNAME> DISPLAY mac
Example
HOSTNAME# display mac

PCMCIAHOSTNAME#1: 00.80.45.06.2e.5d
Output Explanation
1. PCMCIAHOSTNAME#1: MAC address

NTP 279-8013-904
DISPLAY Function
manufacturingid
This command is used to display Manufacturing ID of the SW-CPU card.
(General
Command) Format
HOSTNAME> DISPLAY manufacturingid
Output
xx.xx.xx.xx.xx.xx
1
Output Explanation
1. Manufacturing ID

NTP 279-8013-904
DISPLAY network Function

(General This command is used to display network information.
Command)
Format
HOSTNAME# DISPLAY network
Output
Local Information:
Host Name : ******** 1
IP address : ***.***.***.*** 2
Net Mask : ***.***.***.*** 3
Ether IP Address: ***.***.***.*** 4
Ether net mask : ***.***.***.*** 5
Default router: ***.***.***.*** 6
sysContact : ********************************** 7
sysLocation : ********************************** 8
ATM Address : ****************************** 9
NMS Information:
NMS Number IP address Community name Access privilege
------------------+----------------+-----------------------+----------------
* ***.***.***.*** ******** ********
10 11 12 13

NTP 279-8013-904
Output Explanation
1. Hostname of ATM displayed at the prompt: HOSTNAME
2. ATM IP address
3. Mask value of ATM IP address
4. Ethernet IP address
5. Mask value of Ethernet IP address
6. Default router IP address of Ethernet
7. sysContact of MIB
8. sysLocation of MIB
9. ATM prefix address (node ID)
If the ATM address is less than 26 digits, it will be padded with 0.
10. NMS Number (0-3)
11. IP address of NMS
12. Community Name
13. Access privilege of Management Information Base (MIB)

NTP 279-8013-904
DISPLAY oamcon Function

(General This command is used to display Operations, Administration, and Maintenance
Command) (OAM) connecting point information.
Format
HOSTNAME> DISPLAY oamcon
Output
Line VPI/VCI Line VPI/VCI Point

** ***/*** ** ***/*** *******
1 2 3 4 5
Output Explanation
1. Ingress line number (00~33)
2. Ingress VPI/VCI
3. Egress line number (00~33)
4. Egress VPI/VCI
5. Point type (f4/f5,Segment/End-to-End)

NTP 279-8013-904
DISPLAY oamend Function

(General This command is used to display line status in line number ascending order when
Command) Alarm Indication Signal/Remote Defect Indication (AIS/RDI) cells are received by
the switch at the end point.
Format
HOSTNAME> DISPLAY oamend {P1} {P2} {P3}
Format Explanation
P2 : VPI (0~4095)
P3 : VCI (32~16383)
NOTE When line numbers {P1}and beyond are not specified, the end-point information
and status (AIS/RDI) of all lines is displayed. If specified, the OAM cell being
received when the command is entered is displayed in detail (only the specified
line number, VPI, and VCI are displayed).
Output
When no line is specified:
Line VPI/VCI Status Defect NODE-ID

** ***/*** *** *** **************
1 2 3 4 5
Output Explanation
1. Line number of endpoint
2. VPI/VCI of endpoint
3. Status of endpoint
4. Failure type of endpoint
In case of OC-3c, OC-12c:
LOS, LOF, LOP, LOC, Path AIS (P_AIS), Segment AIS (S_AIS)
In case of TAXI: LOS, LOC
In case of 6.3M: LOS, LOF, LOC, AIS, PAO
In case of DS3, E3:
*LOS, OOF, AIS, LOC, PLCP_LOF, PLCP_OOF
5. Node ID of the defective switch in the AIS/RDI cells

NTP 279-8013-904
Output
When line numbers {P1} and beyond are specified:
Line: xxx 1
VPI: xxx 2
VCI: xxx 3
Point: xxxx 4
Status: xxxx 5
Defect: xxxx 6
Node-ID: xxxxxxxxxxxxxxxxx 7
Output Explanation
1. Line number of endpoint
2. VPI of endpoint
3. VCI of endpoint
4. Endpoint type (F4/F5, Segment/End-to-End)
5. Status of endpoint
6. Failure type of endpoint
In case of OC-3c, OC-12c
Loss of Signal (LOS)
Loss of Frame (LOF)
Loss of Pointer (LOP)
Loss of Cell Delineation (LOC)
Alarm Indication Signal (P_AIS)
Alarm Indication Signal (S_AIS)
In case of TAXI
LOS
LOC
In case of 6.3M
LOS
LOF
LOC
Alarm Indication Signal (AIS)
PAO

NTP 279-8013-904
In case of DS3, E3
LOS
Out of Frame (OOF)
AIS
LOC
Physical Layer Convergence Protocol (PLCP)_LOF
PLCP_OOF
7. Node ID of the defective switch in the AIS/RDI cells.

NTP 279-8013-904
DISPLAY Function
oamf5end
This command is used to display the OAM end points set at F5 (VC level). The
(General end points are displayed in the descending order of line number, VPI, and VCI.
Command)
Format
HOSTNAME> DISPLAY oamf5end
Output
Line VPI VCI

xx xxx xxx
xx xxx xxx
1 2 3
Output Explanation
1. Line Number
2. VPI
3. VCI

NTP 279-8013-904
DISPLAY pnni Function

(General This command is used to display PNNI connection information.
Command)
1. To display PNNI's reachable address:
Format
HOSTNAME> DISPLAY pnni {P1}
Displays PNNI's reachable addresses currently managed by the system set with the
SET pnni address command.
Format Explanation
P1: Address type (Internal/External) may be omitted.
Output
When address type is internal:
Internal reachable address

Address Length Scope Line VPI
xxxxxxxxxxxxxxxxxxxxxxxxxx xx xx xx xxxxx
1 2 3 4 5
When address type is external:
Exterior reachable address

/Transit network ID date /Transit network ID
1 2 3 4 5
/xxxxxxxxxx
6
NOTE Internal address: an end user not supporting Interim Link Management Interface
(ILMI) registration.
External address: an Information Infrastructure Standards Panel (IISP) connected

node/network.

NTP 279-8013-904
When address type is omitted:
Internal reachable address

1 2 3 4 5
Exterior reachable address

/Transit network ID date /Transit network ID
1 2 3 4 5
/xxxxxxxxxx
6
Output Explanation
1. Reachable address
2. Significant address bits
3. Transferable level
5. VPI
6. Other network's identifier

NTP 279-8013-904
2. To display PNNI's architectural variables:
Format
HOSTNAME> DISPLAY pnni architectural
Displays PNNI's timing/rate variables that have been set by SET pnni
architectural command, and are currently managed by the system.
Output
Minimum hello interval(s): xx 1

Hello interval(s): xx 2
DS rxmt interval(s): xx 3
Minimum PTSE interval(s): xx 4
PTSE interval(s): xx 5
Horizontal link inactivity(s): xx 6
Available of cell rate PM(%): xx 7
Available of cell rate mT(%): xx 8
Output Explanation
1. Minimum transmission interval of hello (seconds)
2. Transmission interval of hello (seconds)
3. Transmission interval of database summary packet (seconds) and
communication interval of PNNI Topology State Element (PTSE) request
packet
4. Minimum transmission interval of PTSE (seconds)
5. Communication and retransmission interval of PTSE (seconds)
NOTE One-fifth of this time setting becomes the PTSE response delay time.
6. Ring down recognition time (seconds)
7. Percentage at which average cell rate change is notified (%)
8. Minimum value at which average cell rate change is notified (%)

NTP 279-8013-904
3. To display PNNI connection:
Format
HOSTNAME> DISPLAY pnni connection {P1}
Displays the PNNI path (0, 18) that has been set by the SET pnni connection
command and is currently managed by the system. If a line number is specified,
only the relevant data is displayed. When no line is specified, all the data are
displayed.
Format Explanation
Output
Line VPI VCI Weight Token Best effort band

xx xxx xxxxx xxx xxx xxxx
1 2 3 4 5 6
Output Explanation
2. VPI
3. VCI
4. Administrative weight
5. Aggregation token
6. UBR Best effort separate band

NTP 279-8013-904
4. To display PNNI's longest match table:
Format
HOSTNAME> DISPLAY pnni longestmatch
Displays the flooded reachable addresses in the longest match sequence.
Output
Length Reachable address

O: xxx xxxxxxxxxxxxxxxxxxxxxxxxxx
1 2
Output Explanation
1. Transferable length
2. Reachable address

NTP 279-8013-904
5. To display PNNI routing type:
Format
HOSTNAME> DISPLAY pnni method
Displays the PNNI routing type that has been set by the SET pnni method
command and is currently managed by the system.
Output
Routing method : xxxxxxxx

1
Output Explanation
1. Routing method (HOPBYHOP or SOURCE)
Hopbyhop: IISP
Source: PNNI 1.0

NTP 279-8013-904
6. To display PNNI node information:
Format
HOSTNAME> DISPLAY pnni nodal
Displays the PNNI node information that has been set with the SET pnni nodal
command and is currently managed by the system.
Output
Level indicator : xx 1
Restricted transit bit : xxx 2
Restricted branching bit : xxx 3
ATM end system address : xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx 4
Leadership priority : xx 5
LGN ID : xxxxxxxxxxxxxxxxxxxxxxxxxx 6
Peer group ID : xxxxxxxxxxxxxxxxxxxx 7
Output Explanation
1. Set level indicator
2. Trunk circuit restriction
ON: Disables SVC setups through this switch.
OFF: Allows SVC setups through this switch.
3. P to MP branch point judgement flag
ON: Own node is not used as branch point
OFF: Own node is used as branch point
4. ATM address corresponding to level
5. Priority of becoming peer group leader ("0" cannot be set as PGL)
6. Logical node ID corresponding to level
7. Peer group ID

NTP 279-8013-904
7. To display PNNI reachable node:
Format
HOSTNAME> DISPLAY pnni node
Displays the PNNI logical node recognized by each physical node if a table for
source routing has been prepared in the PNNI routing unit.
Output
Destination node ID Administrative weight

0 : xxxxxxxxxxxxxxxxxxxxxxxxxxxxx 1
1 : xxxxxxxxxxxxxxxxxxxxxxxxxxxxx 1000
: :
: :
1 2
Output Explanation
1. PNNI logical node ID
2. Minimum cost to logical node

NTP 279-8013-904
DISPLAY profile Function

(General This command is used to display the PVC profile information.
Command)
Format
HOSTNAME> DISPLAY profile {P1}
Format Explanation
P1 : Profile name
NOTE If a profile name is specified, only the data related to this profile name is
displayed. If not, all data is displayed.
Output
If the profile name is defaulted:
Profile name Traffic type PCR SCR MBS EPD

********* ******* *** *** *** ***
1 2 3 4 5 6
Output Explanation
1. Profile name
2. Traffic type (CBR, ABR, VBR_RT, VBR_NRT, UBR)
3. Peak Cell Rate (PCR) (cell/s) (- for not used)
4. Sustainable Cell Rate (SCR) (cell/s) (- for not used)
5. Maximum Burst Size (MBS) (cell) (- for not used)
6. Early Packet Discard (EPD) flag (on or off)
If the profile name is specified:
Profile name: ********** 1

Traffic type: ******* 2
Peak cell rate [cell/s]: ******* 3
Sustainable cell rate [cell/s]: ******* 4
Maximum burst size [cell]: ******* 5
EPD: *** 6

NTP 279-8013-904
DISPLAY pvc Function

(General This command is used to display established PVCs for the given port.
Command)
Format
HOSTNAME> DISPLAY pvc P1 {P2} {P3}
NOTE If only the parameter "P1" is entered, all the PVC connections established on that
line will be displayed. If "P1" and "P2" are entered, all PVCs on line "P1" with a
VPI of "P2" will be displayed. If all three parameters are entered, only
information on that one specific connection will be shown.
Format Explanation
P2 : VPI (0~4095) (optional)
P3 : VCI (0~16383) (optional)
Example
HOSTNAME> display pvc 20

Line: 020
Bandwidth Available (Forward/Backward/Line rate): 348207/348207/353207 cell/s
Tunneling bandwidth available : 0/0/0 cell/s
Display/Existing connection
Uni-direction: 0/0 Bi-direction: 1/1
Multipoint: 0/0 Gateway: 2/2
Line VPI/VCI Line VPI/VCI Traffic Connection F-profile B-profile

020 0/5 - - / - - Gateway - -
020 0/16 - - / - - Gateway - -
020 1/100 021 2/200 CBR Bi-direction test test

NTP 279-8013-904
Output
When VCI is not specified:
Line :xxx 1
Bandwidth available (Forward/Backward/Line rate): xxx/xxx/xxx/ cell/s
2
Tunneling bandwidth available : xxx/xxx/xxx/ cell/s
3
Display/Existing connection
Uni-direction: xxxx/xxxx Bi-direction:xxxx/xxxx
Multipoint: xxxx/xxxx Gateway: xxxx/xxxx
4
Line VPI/VCI Line VPI/VCI Traffic Connection F-profile B-profile
xxx xxx/xxx xxx xxx/xxx xxxxxx xxxxxxxxxx xxxxxx xxxxxx
5 6 7 8 9 10 11 12
Output Explanation
2. Band (Forward available/Backward available/Line rate) (- for don't care)
3. Bandwidth for tunneling
4. Number of connection for each type
5. Ingress line number (00~33)
6. Ingress VPI/VCI number
7. Egress line number (00~33)
8. Egress VPI/VCI number
9. Traffic type
10. Connection type
11. Forward profile
12. Backward profile
NOTE If no bandwidth is secured in tunneling, then nothing is displayed for the

bandwidth secured in tunneling.

NTP 279-8013-904
When all parameters are entered (uni-directional):
Connection type: Uni-direction

Traffic type: xxxxxx
Line VPI/VCI Direction Line VPI/VCI UPC Shaper Profile
xxx xxx/xxx -> xxx xxx/xxx xxx xxxx xxxxx
When all parameters are entered (bi-directional):
Connection type: Bi-direction

xxx xxx/xxx -> xxx xxx/xxx xxx xxxx xxxxx
<- xxx xxxx xxxxx
When all parameters are entered (multipoint):
Connection type: Multipoint

xxx xxx/xxx -> leaf 0 xxx xxx/xxx xxx xxxx xxxxx
-> leaf 1 xxx xxx/xxx - xxxx -

NTP 279-8013-904
DISPLAY Function
redundancy This command is used to display the redundancy status of the server card.
(General
Command) Format
HOSTNAME> DISPLAY redundancy {P1}
Format Explanation
Example
HOSTNAME> display redundancy

Slot SoftType Mode Location ACH cause Alarm ID
04 LANE Single/ACT Local - -
12 LANE Duplex/SBY Local Command -
13 LANE Duplex/ACT Local Command -
HOSTNAME> display red 13

Slot: 13
SoftType: LANE
Mode: Duplex/ACT
Location: Local
Remote node ID: -
Remote slot: -
ACH cause: Command
Alarm ID: -
HOSTNAME>
Output
When slot number is omitted:
Slot SoftType Mode Location ACH cause AlarmID

xx xxxx xxxxx/xxx xxxxxx xxxxxxx xxxxxx
1 2 3/4 5 6 7
Output Explanation
1. Slot number
2. Software type in server card (LANE, MPOA)
3. Server card configuration (Single, Duplex)

NTP 279-8013-904
4. Server card operating status

5. Server card configuration location (Local, Remote)
6. Cause of Active Change (ACH)
7. Alarm ID or -
When slot number is specified:
Slot: xx 1
SoftType: xxxx 2
Mode: xxxxx/xxx 3
Location: xxxxx 4
Remote node ID: xxxxxxxxxxxxx 5
Remote slot: xx 6
ACH cause: xxxxxxx 7
Alarm ID: xxxxxx 8
Output Explanation
1. Slot number
2. Software type in server card (LANE, NHRP)
3. Server card operating status (for example, Single/ACT)
4. Server card configuration status (Local, Remote)
5. Remote side switch node ID (when local and duplex: "-")
6. Remote side slot number (when local and duplex: "-")
7. Cause of ACH (Command, Alarm, Other, -)
8. Alarm ID or -

NTP 279-8013-904
DISPLAY route Function

(General This command is used to display the contents of the SVC static routing table. The
Command) contents of this table are set by executing the ROUTE add command. This routing
table is only relevant for IISP (hop-by-hop) routing.
Format
HOSTNAME> DISPLAY route {P1}
Format Explanation
NOTE If a line number is specified, only the data related to this line number is displayed.
If not, all data is displayed for all lines.
Example
HOSTNAME> display route

Destination Type Line VPI
39.877503xxxxxxxxxxxxxxxx.xxxxxxxxxxxx.xx NSAP * 023 -
22 -
Output
Destination Type Line VPI

**********. **********. **********. *************** ** ***
** ***
1 2 3 4
Output Explanation
1. Destination address (NSAP:40char, E.164:16char)
2. Destination address type (NSAP or E.164)
NOTE An asterisk (*) denotes the primary port for routing. Should the primary port fail,
the next port (if specified) will resume routing.
4. Tunneling VPI (- if not tunneling)

NTP 279-8013-904
DISPLAY scope Function

(General This command is used to display the mapping to scope layer.
Command)
Format
HOSTNAME> DISPLAY scope
Output
1 2
uni scope0 : PNNI HierarchyX Level XXX)
Output Explanation
1. Hierarchy number (1-3)
2. Level indicator (0-104)

NTP 279-8013-904
DISPLAY scroll Function

(General This command is used to display the number of lines displayed by the MAT. The
Command) initial value is 24 lines. Number of lines can be changed by executing the
SET scroll command.
Format
HOSTNAME> DISPLAY scroll
Output
If scroll line count is set correctly:
Scroll filter: ON
Number of line: **
1
If scroll line count is set to 0:
Scroll filter: OFF
Output Explanation
1. Number of lines displayed on the MAT screen.

NTP 279-8013-904
DISPLAY server Function

(General This command is used to display TFTP server IP address, default router gateway
Command) IP address, and location name of boot file.
Format
HOSTNAME> DISPLAY server
Example
display server
IP address: [1] 10.1.1.69
Default router IP address: [2] 0.0.0.0
Rboot file name: [3] /2.5G/ver6035/bootfile
Output Explanation
1. IP address of TFTP server. This is for software downloaded from a TFTP
server.
2. Router IP address, if the ATM 2.5 Gbps switch has to "hop" a router to find
the TFTP server.
3. Name of the directory and file for download.
NOTE If no router is present, the IP address will read "0.0.0.0."

NTP 279-8013-904
DISPLAY shaper Function

(General This command is used to display shaping information.
Command)
Format
(1)HOSTNAME> DISPLAY shaper {P1}{P2}
Format Explanation
NOTE All shaper information will be shown unless a specific line {P1} and shaper
number {P2} are entered.
Example
display shaper
Configuration Active
-----------------------+-----------------------
Line Shaper PCR SCR MBS PCR SCR MBS
000 1 1000 500 15 987 493 22
display shaper 00 1
Line: 000
Shaper: 1
Configuration PCR: 1000
Configuration SCR: 500
Configuration MBS: 15
Active PCR: 987
Active SCR: 493
Active MBS: 22
Output
In case of (1):
Configuration Active
-------------+----------
Line Shaper-number PCR SCR MBS PCR SCR MBS
** ** *** *** *** *** *** ***
1 2 3 4 5 6 7 8

NTP 279-8013-904
Output Explanation
2. Shaper number
3. PCR in the configuration data (cell/s)
4. SCR in the configuration data (cell/s) (- if SCR is not registered)
5. MBS in the configuration data (cell) (- if MBS is not registered)
6. PCR under operation (cell/s)
7. SCR under operation (cell/s) (- if SCR is not registered)
8. MBS under operation (cell) (- if MBS is not registered)
In case of (2):
Line: ** 1
Shaper-number: ** 2
Config PCR: ***** 3
Config SCR: ***** 4
Config MBS: ***** 5
Active PCR: ***** 6
Active SCR: ***** 7
Active MBS: ***** 8
PVC's VPI/VCI
***/*** ***/*** ***/*** ***/*** ***/*** 9
SoftPVC's VPI/VCI
***/*** ***/*** ***/*** ***/*** ***/*** 10
Output Explanation
2. Shaper number
3. PCR in the configuration data (cell/s)
4. SCR in the configuration data (cell/s)
5. MBS in the configuration data (cell)
6. PCR under operation (cell/s)
7. SCR under operation (cell/s)
8. MBS under operation (cell)
9. PVC path using the specified shaper-number (VPI/VCI)
10. SoftPVP connection using the specified shaper-number (VPI/VCI)

NTP 279-8013-904
DISPLAY Function
signaling This command is used to display signaling path information the system currently
(General uses (0/5 unless tunneling). If a particular line number is not shown, signaling has
Command) not been set for that line.
Format
HOSTNAME> DISPLAY signaling {P1}
Format Explanation
NOTE If a line number is specified, only the data related to this line number is displayed.
If not, all data is displayed for all lines.
Example
display sig
Line VPI/VCI
000 0/5
001 0/5
02 0/5
Output Explanation
2. VPI/VCI

NTP 279-8013-904
DISPLAY softpvp Function

(General This command is used to display the soft PVPC/PVCC currently set.
Command)
Format
HOSTNAME> DISPLAY softpvp P1 {P2} {P3}
Format Explanation
P2 : Incoming VPI (0~4095)
P3 : Incoming VCI (0, 32~16383)
Example
When only a line number is specified:
Line: 030 1
Local Remote
---------------------------------
Endpoint VPI/VCI Line VPI/VCI TrafficF-prfileB-profile
Calling 1/100 31 1/100 CBR cbr cbr
2 3 4 5 6 7 8
Output Explanation
2. "Calling"/"Called"
3. Local VPI/VCI
4. Remote line number
5. VPI/VCI
6. Traffic type
7. Forward profile
8. Backward profile

NTP 279-8013-904
When VPI is specified:
Line : ** 1
VPI/VCI : ***/*** 2
Traffic type : ***** 3
Endpoint : ***** 4
Retry : ***** 5
Status : ***** 6
Remote
Direction Line VPI/VCI UPC Shaper Profile PCR SCR MBS EPD
-> ** ***/*** *** *** ******* **** **** **** ****
<- *** *** ******* **** **** **** ****
7 8 9 10 11 12 13 14 15 16
Remote node ID
****************************************
17
Output Explanation
2. Local VPI/VCI
3. Traffic type
4. "Calling"/"Called"
5. Number of retry
6. Status (Established, Retry, or Suspended)
7. Direction
9. Remote VPI/VCI
10. UPC function mode
11. Shaper number
12. Profile name (- if it called.)
13. PCR (cell/s)
14. SCR (cell/s)
15. MBS (cell)
16. EPD flag (on or off)
17. Remote node ID

NTP 279-8013-904
Local Remote
--------------------------------+---------------------------------
Line VPI/VCI Line VPI/VCITrafficF-profileB-profile
xxxxxx xxxx/xxxx xxx xxxx/xxxxxxxxxxxxxxxxxxxxxx
xxxxxx xxxx/xxxx xxx xxxx/xxxxxxxxxxxxxxxxxxxxxx
1 2 3 4 5 6 7
Output Explanation
1. Local line number
2. Local VPI/VCI
4. Remote VPI/VCI
5. Traffic type
6. Forward profile
7. Backward profile

NTP 279-8013-904
DISPLAY sscop Function

(General This command is used to display Service Specific Connection Orientation
Command) (SSCOP) parameters.
Format
HOSTNAME> DISPLAY sscop
Example
display sscop
Line VPI MaxCC TimerCC Keepalive NORESP POLL MaxPD MaxSTAT clr-buff
[1] [2] [3] [4] [5] [6] [7] [8] [9] [10]
000 0 4 1 30 10 1 10 4 Yes
001 0 4 1 30 10 1 10 4 Yes
122 003 0 4 1 30 10 1 10 4 Yes
Output Explanation
2. VPI
3. MaxCC
Maximum number of messages that can be sent without the SSCOP waiting
for a reply.
4. TimerCC (sec)
Retransmission interval when no response message is received for connection
setting, release, realignment, or restoration.
5. Timer_KEEPALIVE(sec)
Time that the connection can be maintained without any data transfer.
6. Timer_NORESPONSE (sec)
Time that the connection can be maintained without receiving a status request
message.
7. Timer_POLL (sec)
Transmission interval of status request message.
8. MaxPD
Maximum number of data messages that are sent after the SSCOP sends a
status notice message.

NTP 279-8013-904
9. MaxSTAT
Maximum number of elements contained in a status notice message. (Elements
refer to the combination of the beginning and end of unreceived data message
number +1.)
10. Clear-buffers
Asks the question, "must the transmission queue of the transmission buffer be
cleared after the connection is released?" (Y or N).

NTP 279-8013-904
DISPLAY status Function

(General This command is used to display the hardware status. When this command is
Command) entered, the system performs an installation check.
The system displays the status of all installed switch components, including power,
fan units, and interface cards.
Format
HOSTNAME> DISPLAY status
Example
Environment: xx 1
Power0: xxxxxxxxxxxxx 2
Power1: xxxxxxxxxxxxx
FAN0: xxxxxxxxxxxxx 3
FAN1: xxxxxxxxxxxxx
FAN2: xxxxxxxxxxxx
CPU: xxxxxxxxxx 4
Switch: xxxxxxxxxx 5
Slot: x 6
Slot: xxxxxxxxxxx 7
Slot: xxxxxxxx 8
Slot: xxxxxxxxxxxxx 9
Output Explanation
1. Environment status (normal, failure)
2. Power Unit status (normal, failure)
3. Fan status (normal, failure)
4. CPU status (normal, failure, diagnostics, diagnosis status NG)
5. Switch status (initializing, normal, failure, diagnostics, diagnosis status NG)
6. Slot installation status (0~3)
7. Buffer type (Buffer1, Buffer2, FR Buffer1, FR Buffer2, initializing, not
installed)
If no line package is installed, the Not installed message is displayed. If a

NOTE
package was inserted in this line card slot in the past, the system still has the
configuration data of that package and will display the package information
(buffer and card type) before the Not installed message.
This information will not be displayed after the CLEAR config [slot]
command is input to delete the retained configuration data.

NTP 279-8013-904
8. Line type
OC-12c/STM4 (SMF-S) TypeA

OC-12c/STM4 (SMF-S) TypeB
OC-12c/STM4 (MMF)
OC-12c/STM4 (SMF-L)
OC-3c/STM1 (SMF-L)
OC-3c/STM1 (MMF)
OC-3c/STM1 (STF-S)
UTP-5
J2 (3M-6M)
Primary
100M-TAXI
DS3
E3
DS1
E1
CD-DS1
STS-3c/STM1 (COAXIAL)
FD-DS1
SERVER
SERVER 2
9. Line Board status (0~3)
Normal
Initializing
Failure
Diagnostics
Diagnosis status NG
Configuration data is kept

NTP 279-8013-904
DISPLAY svc Function

(General This command is used to display SVC connections and associated information
Command) currently established on a given line.
Format
HOSTNAME> DISPLAY svc P1 {P2} {P3}
Format Explanation
P2: VPI (0~4095)
P3: VCI (0, 32~16383)
Example
HOSTNAME>
HOSTNAME> display svc 10

Line: 010
Bandwidth Available (Forward/Backward/Line Rate): 353207/353207/353207 cell/s
Tunneling bandwidth available : 0/0/0 cell/s
Existing connections: 3
Incoming Outgoing
---------------+---------------
Traffic type Connection type Line VPI/VCI Line VPI/VCI
UBR P-to-M 040 0/6072 010 0/48
UBR P-to-M 040 0/6076 010 0/50
UBR P-to-P 010 0/47 040 0/3099
Output
All SVCs will be displayed for a given port (P1) unless a specific VPI {P2} / VCI
{P3} is given.
Line : ** 1
Bandwidth available (Forward/Backward/Line rate):*****/*****/*****cell/s 2
Tunneling bandwidth available:xxx/xxx/xxx cell/s 3
Existing connections:**** 4
IncomingOutgoing
Traffic type Connection TypeLineVPI/VCILineVPI/VCI
**** **** **** ***********/***
5 6 7 8 9 10

NTP 279-8013-904
Output Explanation
2. Bandwidth (forward/backward/specified line capacity)
3. Secured band in tunneling
4. Number of connections
5. Traffic type
6. Connection type
7. Incoming line number
8. Incoming VPI/VCI
9. Outgoing line number
10. Outgoing VPI/VCI
NOTE If no band is secured in tunneling, then nothing is displayed for the band secured
in tunneling.

NTP 279-8013-904
Example
display svc 10 0 51
Connection Type: P-to-P
Traffic Type: UBR
Traffic parameters information:

PCR SCR MBS
Direction CLP=0 CLP=0+1 CLP=0 CLP=0+1 CLP=0 CLP=0+1 Tagging
-> - 365566 - - - - off
<- - 365566 - - - - off
Incoming information:
Line VPI/VCI UPC Shaper
010 0/51 off off
Outgoing information:
002 0/147 1 off
Calling information:
Line Call ref. Type Address
010 4 NSAP 39.877501000000000000000000.00A024B28F50.00
Called information:
Line Call ref. End ref. Type Address
002 36953 - NSAP 39.877501000000000000000000.000077875EA6.00

NTP 279-8013-904
Output
Connection Type : xxxxxx 1

Traffic Type : xxx 2
Traffic parameters information :

PCR SCR MBS
Direction CLP=0 CLP=0+1 CLP=0 CLP=0+1 CLP=0 CLP=0+1
Tagging
-> xxx xxx xxx xxx xxx
xxx xxx
<- xxx xxx xxx xxx xxx
xxx xxx
3 4 5 6 7 8
9 10
Incoming information :
xxx xxx/xxx xxx xxx
11 12 13 14
Outgoing information :
xxx xxx/xxx xxx xxx
15 16 17 18
Calling information :
Line Call ref. Type Address
xxx xx xxxx xx.
xxxxxxxxxxxxxxxxxxxxxxxx. xxxxxxxxxxxx. xx
19 20 21 22
Called information :
Line Call ref. End ref.Type Address
xxx xx xx xxxx xx.
xxxxxxxxxxxxxxxxxxxxxxxx. xxxxxxxxxxxx. xx
23 24 25 26 27
NOTE If the SVC being displayed is a point-to-multipoint SVC, the response shows only
one of the leaves of the multipoint SVC, even if more leaves exist.

NTP 279-8013-904
Output Explanation
1. Connection type (P-to-P, P-to-M : (SoftPVP), (RCC))
2. Traffic type
3. Direction of the connection
4. PCR (cell/sec) in case of CLP=0 or -
5. PCR (cell/sec) in case of CLP=0+1 or -
6. SCR (cell/sec) in case of CLP=0 or -
7. SCR (cell/sec) in case of CLP=0+1 or -
8. MBS (cell) in case of CLP=0 or -
9. MBS (cell) in case of CLP=0+1 or -
10. Tagging (on, off or -)
11. Incoming line number or -
12. Incoming VPI/VCI or -
13. Incoming UPC mode (off, 1-5) or -
14. Incoming shaper (off, 1-8) or -
15. Outgoing line number or -
16. Outgoing VPI/VCI or -
17. Outgoing UPC mode (off, 1-5) or -
18. Outgoing shaper (off, 1-8) or -
19. Calling line number or -
20. Calling call reference or -
21. Calling address type or -
22. Calling address or -
23. Called line number or -
24. Called call reference or -
25. Called end reference or -
26. Called address type or -
27. Called address or -

NTP 279-8013-904
DISPLAY svcline Function

(General This command is used to display the current SVC signaling status of the line
Command) interfaces.
Format
HOSTNAME> DISPLAY svcline {P1}
Format Explanation
Example
HOSTNAME> display svcl

Line VPI Configuration Active
000 0 Resume Suspend
001 0 Resume Normal
002 0 Resume Normal
003 0 Resume Normal
Output
Line VPI Configuration Active

** *** ******* *******
1 2 3 4
Output Explanation
1. Line number
2. VPI of the signaling channel
3. Signaling status in the configuration data
Suspend (SET svcline command)
Resume (SET svcline command)
4. Signaling status under operation
Suspend (disabled or not physically connected)
Resume (connected and operational)
Normal
NOTE SVC status becomes Suspend during line failure or "Admin Down," even if the
configuration is set to Resume.

NTP 279-8013-904
DISPLAY t309trg Function

(General
This command is used to display the timing when signaling
Command)
line failure is recognized.
Format
HOSTNAME> DISPLAY t309trg
Output
Timing value: xxxx

1
Output Explanation
1. Timer value (1~ 511[sec] or -)

NTP 279-8013-904
DISPLAY Function
telnetlimit This command is used to display the time limit of Telnet.
(General
Command) Format
HOSTNAME> DISPLAY telnetlimit
Example
display tel
Telnet time-limit : 10[min]
Output
If no time limit is set:
No Telnet time-limit.
If time limit is set:
Telnet time-limit : ***** [min]

1
Output Explanation
1. Telnet will automatically disconnect upon expiration of the given time limit
after the last activity.
Setting the time limit to zero allows the Telnet session to stay open indefinitely.

NTP 279-8013-904
DISPLAY time Function

(General This command is used to display system date and time.
Command)
Format
HOSTNAME> DISPLAY time
Example
display time
97-12-10 11:39:54
Output
YY-MM-DD hh:mm:ss
1 2
NOTE YY-MM-DD indicates the year (the last two digits of the year), month, and day of
the month.
hh:mm:ss indicates the hour, minute, and second.
Example
1. January 10, 1999 is displayed as: 99-01-10
2. 2:30 p.m. and 15 seconds is displayed as: 14:30:15

NTP 279-8013-904
DISPLAY traffic Function

(General
This command is used to display traffic and performance information of each line,
Command) connection, and physical unit.
The command format differs depending on line, connection, or physical unit.
Format
1. HOSTNAME> DISPLAY traffic line P1
2. HOSTNAME> DISPLAY traffic connection P1 P2 P3
3. HOSTNAME> DISPLAY traffic physical P1
Format Explanation
P1 : Line Number (00~33)
P2 : VPI (0~4095)
P3 : VCI (0, 32~16383)

NTP 279-8013-904
Output of Format 1:
Line: xxx 1
Total of received cells: xxxxxxxxxx 2
Total of transmitted cells: xxxxxxxxxx 3
Total of misdelivered cells: xxxxxxxxxx 4
Total of threshold excess cells: xxxxxxxxxx 5
Total of UPC violated cells: xxxxxxxxxx 6
Output Explanation
1. Line Number
2. Received cell count on each line
3. Transmitted cell count on each line
4. Transmission side undefined cell count on each line
5. Number of dropped cells due to an exceeded threshold on each line
Possible causes are an excess of lower priority threshold, an excess of
maximum threshold, and an excess of EPD threshold.
6. Number of UPC violation cells of each line

NTP 279-8013-904
In case of FR-DS1:
Line: xx Received Transmitted 1

Total of throughput frames: xxxxxxxxxx xxxxxxxxxx 2
Total of error frames: xxxxxxxxxx xxxxxxxxx 3
Total of congestion discard frames: xxxxxxxxxx xxxxxxxxxx 4
Total of LMI (Status) frames: xxxxxxxxxx xxxxxxxxxx 5
Output Explanation
1. Line Number
2. Received/Transmitted throughput frame count
3. Received/Transmitted error frame count
4. Received/Transmitted congestion discard frame count
5. Received/Transmitted LMI input frame count
This command is valid for Buffer 2 (except CE-J2/DS1/E1/DS3). If a command of

NOTE
that format is entered for any other buffer, an error message will be displayed.

NTP 279-8013-904
Output of Format 2, in case of uni-direction:
Connection type: xxx Uni-direction

1
Line VPI/VCI Line VPI/VCI
xx xxxx/xxxx xx xxxx/xxxx
2 3 4 5
Number of received cells: xxxxxxxxxx 6
Number of transmitted cells: xxxxxxxxxx 7
Number of dropped received cells: xxxxxxxxxx 8
Output Explanation
1. PVC/SVC
2. Point 1 Line Number
3. Point 1 VPI/VCI
5. Point 2 VPI/VCI
6. Received cell count of Point 1
7. Transmitted cell count of Point 2
8. Number of received drop cells of Point 1
maximum threshold, a UPC violation, and an excess of EPD threshold.
When "traffic" is set in NMS, not "Number" but "Total" will be displayed. If the
NOTE
buffer of the specified line is FR-buffer, an error will occur.

NTP 279-8013-904
Output of Format 2, in case of bi-direction:
Connection type : xxx Bi-direction

1
Line VPI/VCI Line VPI/VCI
xxx xxxx/xxxx xxx xxxx/xxxx
2 3 4 5
Number of dropped received cells:xxxxxxxxxx 8
Output Explanation
1. PVC/SVC
3. Point 1 VPI/VCI
5. Point 2 VPI/VCI
maximum threshold, a UPC violation and an excess of EPD threshold.
When "traffic" is set in NMS, not "Number" but "Total" will be displayed. Bi-
NOTE
directional traffics are displayed on two lines for each direction. Therefore, the
"Incoming" and "Outgoing" information sets are replaced by each other on the top
and bottom lines.

NTP 279-8013-904
Output of Format 2, in case of PVC Multicast / SVC P-to-MP:
Connection type : xxx Multipoint

1
Line VPI/VCI
xx xxxx/xxxx
2 3
Number of received cells:xxxxxxxxxx4
Number of dropped received cells:xxxxxxxxxx5
Line VPI/VCI Transmitted cells

Leaf 0 xx xxxx/xxxx xxxxxxxxxx
6 7 8
Output Explanation
1. PVC/SVC
3. Point 1 VPI/VCI
7. Point 2 VPI/VCI
NOTE

NTP 279-8013-904
Output of Format 2, in case of PVC GWPAD-path:
Connection type : PVC Gateway

Line VPI/VCI
xx xxxx/xxxx
1 2
Number of dropped received cells:xxxxxxxxxx 5
Output Explanation
2. Point 1 VPI/VCI
NOTE

NTP 279-8013-904
Output of Format 3, in case of OC3, OC12, J2, Primary and STS-3c/STM1

(COAXIAL):
Line : xx 1
Receive cell count: xxxxxxxxxx 2
Transmit cell count: xxxxxxxxxx 3
HEC error cell count: xxxxxxxxxx 4
Corrected HEC error cell count: xxxxxxxxxx 5
Uncorrected HEC error cell count: xxxxxxxxxx 6
B1 error count: xxxxxxxxxx 7
Path FEBE count: xxxxxxxxxx 10
Line FEBE count: xxxxxxxxxx 11
Output Explanation
1. Line Number
2. Received cell count
3. Transmitted cell count
4. HEC error cell count
5. Corrected HEC error cell count
6. Uncorrected HEC error cell count
7. B1 error cell count
10. Path FEBE (Far End Block Error) count
11. Line (Section) FEBE (Far End Block Error) count
NOTE Counters that cannot be displayed due to package type will be represented as "-".

NTP 279-8013-904
Output of Format 3, in case of DS3:

Line: xx 1
Idle/Unassigned cell count: xxxxxxxxxx 4
Uncorrected HEC error cell count:xxxxxxxxxx 5
FEBE error count: xxxxxxxxxx 6
Framing error count: xxxxxxxxxx 8
FEBE event count: xxxxxxxxxx 9
Path parity error count: xxxxxxxxxx 10
Parity error count: xxxxxxxxxx 11
SEZ detect count: xxxxxxxxxx 12
F-bit or M-bit error count: xxxxxxxxxx 13
Line code violation count: xxxxxxxxxx 14
Output Explanation
1. Line Number
4. Idle/Unassigned cell count
6. FEBE (Far End Block error) counts in PLCP mode
7. BIP (Bit Interleaved Parity) error counts in PLCP mode
8. Framing Pattern Octet error counts and Path Overhead Identification Octet
error counts in PLCP mode
9. FEBE (Far End Block Error) count
10. C-bit parity error counts
11. P-bit parity error counts
12. Summed Excessive Zero detected count
13. F-bit/M-bit error count
14. Line Code Violation error count
Counters that cannot be displayed due to DS3 mode will be represented as "-".
NOTE

NTP 279-8013-904
Output of Format 3, in case of E3:
Line : xx 1
Idle/Unassigned cell count: xxxxxxxxxx 4
FEBE error count: xxxxxxxxxx 6
BIP-8 error count: xxxxxxxxxx 10
IEC error count: xxxxxxxxxx 11
Framing pattern error count: xxxxxxxxxx 12
Output Explanation
1. Line Number
4. Idle/Unassigned cell count
6. FEBE (Far End Block error) counts in PLCP mode
7. BIP (Bit Interleaved Parity) error counts in PLCP mode
8. Framing Pattern Octet error counts and Path Overhead Identification Octet
error counts in PLCP mode
10. Bit Interleaved Parity-8 error counts
11. Incoming error counts
12. Framing pattern error count
Counters that cannot be displayed due to E3 mode will be represented as "-".

NOTE

NTP 279-8013-904
Output of Format 3, in case of DS1:
Line : xx 1
Framing bit error count: xxxxxxxxxx 2
CRC error count: xxxxxxxxxx 3
PLCP FEBE error count: xxxxxxxxxx 8
Output Explanation
1. Line Number
2. Framing Bit error count
3. CRC error count
6. B1 error count
7. Framing error count
8. PLCP FEBE (Far End Block Error) count
Counters that cannot be displayed due to DS1 mode will be represented as "-".
NOTE

NTP 279-8013-904
Output of Format 3, in case of E1:
Line : xx 1
PLCP FEBE error count: xxxxxxxxxx 3
Line code violation count: xxxxxxxxx 9
Output Explanation
1. Line Number
3. PLCP FEBE (Far End Block Error) count
4. B1 error count
5. Framing error count
8. CRC error count
Counters that cannot be displayed due to E1 mode will be represented as "-".

NOTE

NTP 279-8013-904
Output of Format 3, in case of CE-DS1:
Line : xx 1
Path parity error count: xxxxxxxxxx 3
Parity error count: xxxxxxxxxx 4
Line code violation count:xxxxxxxxxx 7
Bit error count: xxxxxxxxxx 8
Output Explanation
1. Line Number
3. C-bit parity error counts
4. P-bit parity error counts
6. CRC error count
8. Bit error count
NOTE Counters that cannot be displayed due to package type will be represented as "-".

NTP 279-8013-904
Output of Format 3, in case of FR-DS1:
Line : xx 1
Line code violation count:xxxxxxxxxx 5
Output Explanation
1. Line Number
2. FEBE counts (Far End Block error counts)
3. Framing Bit error counts
4. CRC error counts
5. LCV error counts (Line Code Violation error counts)
NOTE Counters that cannot be displayed due to package type will be represented as -.

NTP 279-8013-904
DISPLAY Function
tunneling This command is used to display tunneling connection information.
(General
Command) Format
HOSTNAME> DISPLAY tunneling
Example
display tun
Line VPI Throughput UPC Shaper
000 1 1000 1 1
Output
Line VPI Throughput UPC Shaper

** *** ****** *** ***
1 2 3 4 5
Output Explanation
1. Line number
2. VPI
3. Tunneling bandwidth (cell/s)
4. Forward UPC function mode (off or 1)
5. Forward shaper number (off or 1-8)

NTP 279-8013-904
DISPLAY version Function

(General This command is used to display the Software Version, boot program, and
Command) configuration data.
Format
HOSTNAME> DISPLAY version
Example
HOSTNAME# display version

Software version: 6.0(3) , 32Mbytes
Boot program version: 3.01 4 Nov 97

NTP 279-8013-904
ENABLE Function
(General This command is used to switch from General Command Mode to Privileged
Command) Command Mode.
Privileged Command Mode is a function to be used by the system manager. It is
necessary to register a password in advance to use the ENABLE command to switch
modes. If this command is executed when there is no password registered, you will
be prompted to register a password.
Format
HOSTNAME> ENABLE
Example
enable
Input new enable password:
Retype new enable password:
Do not push reset button until save finishes

#######
[OK]
##
Input new Telnet password:
Retype new Telnet password:
Do not push reset button until save finishes

#######
[OK]
Output
If no password has been registered:

[OK]

NTP 279-8013-904
If a password has been registered:
Input enable password:
If no Telnet password has been registered:

[OK]
NOTE Password is not displayed on the screen
Only alphanumeric characters may be used in the password. (Symbols such as +,

=, %, and & may not be used.)
Password characters are case-sensitive.
Do not forget the password once it is registered.
The password must contain no less than four and no more than eight characters. If
the correct password is entered, the prompt will change from > to # to indicate
that a Privileged Command may be entered. Once you complete password in
the Privileged Command Mode, be sure to use the EXIT command to return to the
General Command Mode.

NTP 279-8013-904
EXIT (General Function

Command) The user can log out by entering this command in the General Mode during Telnet
connection.
Format
HOSTNAME> EXIT
Output
none

NTP 279-8013-904
EXIT (Privileged Function

Command) This command is used to switch from the Privileged Command Mode to General
Command Mode.
The prompt will change from # to >.
Format
HOSTNAME# EXIT
Output
HOSTNAME>
NOTE To prevent the set data of the ATM switch from being changed by unauthorized
personnel, be sure to return to the General Command Mode after completing work
in the Privileged Command Mode.

NTP 279-8013-904
FAILUREDUMP Function
(Privileged
This command is used to display the failure information. The failure information
Command) is the information for system administrators to use for software analysis.
Format
HOSTNAME# FAILUREDUMP P1 {P2}
Format Explanation
P1: Log Number (1~2)
P2: Display Information (all)
If Display Information parameter is not specified, only the information

NOTE
collected by OS is displayed and the information collected by the application is
not. If all is specified, the information collected by both OS and application is
displayed. The information collected by application includes alarm log
information.
Output
###################################
# Failure dump #
###################################
LM version : x.x(x).x xxxx xxxx.xxx.x 1
ROM version : x.xx xx xxx xx 2
Fault occurred time : xx-xx-xx : xx : xx : xx 3
Exception name : xxxx 4
Fault kind : xxxxxxxx 5
TKN : xxxxxxxx 6
INT0: xxxxxxxx 7
INT1: xxxxxxxx
INT2: xxxxxxxx
INT3: xxxxxxxx
INT4: xxxxxxxx
##### VR4300 CPU Registers ##### 8

$0=xxxxxxxx at=xxxxxxxx v0=xxxxxxxx v1=xxxxxxxx
a0=xxxxxxxx a1=xxxxxxxxa 2=xxxxxxxx a3=xxxxxxxx
t0=xxxxxxxx t1=xxxxxxxx t2=xxxxxxxx t3=xxxxxxxx
t4=xxxxxxxx t5=xxxxxxxx t6=xxxxxxxx t7=xxxxxxxx
t8=xxxxxxxx t9=xxxxxxxx k0=xxxxxxxx k1=xxxxxxxx
s0=xxxxxxxx s1=xxxxxxxx s2=xxxxxxxx s3=xxxxxxxx
s4=xxxxxxxx s5=xxxxxxxx s6=xxxxxxxx s7=xxxxxxxx
gp=xxxxxxxx sp=xxxxxxxx fp=xxxxxxxx ra=xxxxxxxx
hi=xxxxxxxx lo=xxxxxxxx

NTP 279-8013-904
##### VR4300 CP0 Registers ##### 9

epc =xxxxxxxx status =xxxxxxxx cause =xxxxxxxx
badvaddr =xxxxxxxx count=xxxxxxxx compare =xxxxxxxx
watchlo =xxxxxxxx watchhi =xxxxxxxx content =xxxxxxxx
ecc =xxxxxxxx cacheerr =xxxxxxxx errepc =xxxxxxxx
content =xxxxxxxx
pagmask =xxxxxxxx wired =xxxxxxxx config =xxxxxxxx
lladdr =xxxxxxxx taglo =xxxxxxxx taghi =xxxxxxxx
entry_hi =xxxxxxxx entry_lo0 =xxxxxxxx entry_lo1=xxxxxxxx
index =xxxxxxxx random =xxxxxxxx prid =xxxxxxxx
### Stack ( SP ) ### 10

******** : xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx
.......... ********
: xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx..........
..........
|
|
|
..........
..........
..........
Run task ID : xxxxxxxx 11

Run task sp addr : xxxxxxxx 12
### Stack ( run task ) ### 13
..........
..........
..........
|
|
|
..........
..........******** : xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx
..........

NTP 279-8013-904
Output Explanation
1. Software version
2. Boot program version)
3. Failure occurred time (yy - mm - dd : hh : mm : ss)
4. Exception cause (See below)
Exception Cause Type of Exception

Int Interrupt exception
Mod TLB modified exception
TLBL TLB invalid exception (load or fetch)
TLBS TLB invalid exception (store)
AdEL Address error exception (load or instruction fetch)
AdES Address error exception (store)
IBE Bus error exception (instruction fetch)
DBE Bus error exception (load or store data)
Sys System call exception
BP Breakpoint exception
RI Reserved instruction exception
Cpu Co-processor unusable exception
Ov Integer overflow exception
Tr Trap exception
FPE Floating-point exception
WATCH Watch exception
WDT WDT overflow
5. Exception occurrence mode [-1 (task runnning), -2 (Kernel running), -3 (not-

task)]
6. Exception task token
7. Interruption control [cause of each interrupt (INT0 - INT 4), trigger, contents
of mask]
8. VR4300 CPU registers
9. VR4300 CPO registers
10. Stack information indicated by CPU stack pointer (SP) register
[Display size: 1024 (byte)]
11. RUN status task ID

NTP 279-8013-904
12. RUN status task stack area base address

13. RUN status task stack information [Display size: 1024 (byte)]
14. Alarm log information [Display size: 69104 (byte)]
If display information parameter is not specified, the 14th item is not displayed.
NOTE
xxxxxxxx is displayed for the registers that are not collected.

NTP 279-8013-904
FAILURELOG Function
(Privileged This command is used to display the failure log information.
Command)
Format
HOSTNAME# FAILURELOG
Output
Log no Occurred time Exception name

x xx-xx-xx:xx:xx:xx xxxx
x xx-xx-xx:xx:xx:xx xxxx
1 2 3
Output Explanation
1 : Log number (1 - 2)
2 : Failure occurred time ( yy - mm - dd : hh : mm : ss, ------------- is displayed

when failure information is not being logged.)
3 : Exception cause
Exception Cause Type of Exception

Int Interrupt exception
Mod TLB modified exception
TLBL TLB invalid exception (load or fetch)
TLBS TLB invalid exception (store)
AdEL Address error exception (load or instruction fetch)
AdES Address error exception (store)
IBE Bus error exception (instruction fetch)
DBE Bus error exception (load or store data)
Sys System call exception
BP Breakpoint exception
RI Reserved instruction exception
Cpu Coprocessor unusable exception
Ov Integer overflow exception
Tr Trap exception
FPE Floating-point exception
WATCH Watch exception
WDT WDT overflow

NTP 279-8013-904
GENERATE ? Function
(Privileged This command is used to display the help message for the GENERATE command.
Command)
Format
HOSTNAME# GENERATE ?
Output
f4 VP level
f5 VC level
feac FEAC Code generate for DS3

NTP 279-8013-904
GENERATE f4 Function
(Privileged This command is used to generate OAM cells (loopback cells) in the "f4" mode to
Command) perform loopback test.
An autonomous message indicating the result of the test is output to the MAT.
Format
HOSTNAME# GENERATE f4 P1 P2 P3 P4 P5 P6
Format Explanation
P1 : Test base flow (0|seg (segment base) or 1|end (end-to-end base))
P2 : Node ID of the switch which returns loopback cell (up to 13-octet)
P3 : Correlation tag (up to 4 hexadecimal octets)
P4 : Loopback test count (1~16)
P6 : VPI (0~4095)
Example
gen f4 0 398 12345678 2 30 1

Generating OAM cells...
NOTE The loopback test can only start if the node ID for the switch is set with the
SET local command.

NTP 279-8013-904
GENERATE f5 Function
(Privileged This command is used to generate Operations, Administration, and Maintenance
Command) (OAM) cells (loopback cells) in the "f5" mode to perform loopback test.
An autonomous message indicating the result of the test is output to the MAT.
Format
HOSTNAME# GENERATE f5 P1 P2 P3 P4 P5 P6 P7
Format Explanation
P1 : Test base flow (0|seg (segment base) or 1|end (end-to-end base))
P2 : Node ID of the switch which returns loopback cell(up to 13-octet)
P3 : Correlation tag (up to 4 hexadecimal octets)
P4 : Loopback test count (1~16)
P6 : VPI (0~4095)
P7 : VCI (32~16383)
Example
Privileged Command# gen f5 0 39866501 87

654321 2 30 0 50
NOTE The loopback test can only start if the node ID of the switch is set with the
SET local command.

NTP 279-8013-904
GENERATE feac Function

(Privileged This command is used to transmit Feature Code (FEAC) at DS3 package in C-bit
Command) parity mode.
Format
HOSTNAME# GENERATE feac P1 P2
Format Explanation
P2: Command condition
0 : Line loopback activated
1 : Line loopback deactivated
Example
HOSTNAME# gen feac 00 0
NOTE FEAC code can only be transmitted when DS3 line is set to C-bit parity mode.

NTP 279-8013-904
INSTALL config Function

(Privileged This command is used to download previously backed-up data from a TFTP server
Command) via the Ethernet port.
Format
HOSTNAME# INSTALL P1 P2 P3
Format Explanation
P1 : Data type (system or config)
P2 : IP address (x.x.x.x (x=0~255))
P3 : Directory and file name
Setting Procedure
1. Before installing configuration data, a previously backed-up file must be
present. See BACKUP config command.
2. If a gateway is present between the TFTP server and the switch, set the IP
routing information by executing the SET iproute command.
3. To install the data via ATM, set the ATM IP address of the switch by executing
the SET local command. To install the data via Ethernet, set the switch
Ethernet IP address by executing the SET ether command.
4. The switch will restart if the installation fails. Therefore, it is recommended
that you save the data using the SAVE command.
5. Perform the installation by executing the INSTALL command.
6. Save the newly installed data by executing the SAVE command.
Example
HOSTNAME# install config 10.1.1.3 /2.5G/config/file1

</2.5G/config/file1>

NTP 279-8013-904
Output
In case of system install:
System files have been loaded.
In case of config install:
Configuration data have been loaded/written.
NOTE A file of up to 2 MB in size may be booted by system installation.
Specify a file prepared by the BACKUP command for the config installation.
If an installation error is detected, reset and return to the operation status, or re-
enter the installation command.
It is impossible to resume system installation after the write to flash memory fails.
Therefore, when starting the system the next time, do so in the boot mode.
When booting the system from NMS via ATM line, set the NMS information with
SET nms command in the applicable switch in advance.
When booting the system from a workstation via ATM/Ethernet, set the IP route
by executing the SET iproute command in the applicable switch in advance.
The system will automatically reset after the installation is properly completed.

NTP 279-8013-904
OPEN (General Function

Command) This command is used to open access to a server card interface, for example, LANE
server card, IP.
Format
HOSTNAME> OPEN P1
Format Explanation
P1: Slot number (0-3)
Output
If no password has been registered:
Input new password:

Retype new password:
[OK]
If a password has been registered:
Input password:
Card02#
NOTE When this command is entered, all control is passed to the specified card. When
the EXIT command is executed, control is returned to the active CPU.

NTP 279-8013-904
PASSWD Function
(Privileged This command is used to change the password for switching to the Privileged
Command) Command Mode.
After entering the current password, enter the new password twice to complete the
password change. The entered characters are not echoed back.
Format
HOSTNAME# PASSWD
Output
If a password is registered:
Input old password:

[OK]
NOTE The password must contain no less than four and no more than eight characters.
The password is case sensitive.

NTP 279-8013-904
PVC ? (Privileged Function

Command) This command is used to display the help message for the Permanent Virtual Circuit
(PVC) command.
Format
HOSTNAME# PVC ?
Output
add Add endpoint to existing uni-directional multipoint

PVC PVC
delete Delete PVC
establish Establish PVC
flush Delete all PVCs on a line interface
remove Remove endpoint from existing uni-directional multi-
point PVC

NTP 279-8013-904
PVC add Function

(Privileged This command is used to add a PVC end point or "leaf" to an existing multipoint.
Command) Before entering this command, use the SHOW PVC (or PVC establish)
command to verify a previously set multipoint route, to which a leaf may be added.
Enter the same incoming side parameters (line number, VPI, VCI) that have
been set as the incoming side parameters with the PVC establish command.
The type of end point bit rate (traffic type and throughput) is the same as that
set with PVC establish.
Reference Command
DISPLAY pvc
Cancel Command
PVC remove, PVC flush, SHOW pvc
Format
HOSTNAME# PVC add P1 P2 P3 P4 P5 P6
Format Explanation
P1: Ingress line number (00~33)
P2: Ingress VPI number (0~4095)
P3: Ingress VCI number (0, 32~16383)
P4: Egress line number (00~33)
P5: Egress VPI number (0~4095)
P6: Egress VCI number (0, 32~16383)
Example
HOSTNAME# SET profile 1 cbr

HOSTNAME# PVC establish 1 1 40 1 100 42 2 200 0 0 cbr
HOSTNAME# pvc add 40 1 100 43 2 200

NTP 279-8013-904
Output
***Connection endpoint has been added.

Connection type : Multipoint
Traffic type : ****
** ***/*** -> leaf 0 ** ***/*** *** *** *****
-> leaf 1 ** ***/*** - *** -
-> leaf 2 ** ***/*** - *** -
-> leaf 3 ** ***/*** - *** -

NTP 279-8013-904
PVC delete Function

(Privileged This command is used to delete a previously established PVC (not a leaf).
Command) If the connection is a multipoint, execute only after removing all leafs with the
PVC remove command (described later in this chapter).
Format
HOSTNAME# PVC delete P1 P2 P3 P4 P5 P6 P7
Format Explanation
P1 : Connection type (0 (bi-directional), 1 (multipoint) or 2 (uni-directional))
P3 : Ingress VPI (0~4095)
P4 : Ingress VCI (0, 32~16383)
P7 : Egress VCI (0, 32~16383)
Example
HOSTNAME# PVC delete 0 10 1 100 20 2 200
Output
In case of uni-directional:
***Connection has been deleted.

Connection type : Uni-direction
Traffic type : ****
** ***/*** -> ** ***/*** *** *** *****

NTP 279-8013-904
In case of bi-directional:

Connection type : Bi-direction
Traffic type : ****
** ***/*** -> ** ***/*** *** *** *****
<- ** ***/*** *** *** *****
In case of multipoint:

Traffic type : ****
** ***/*** -> leaf 0 ** ***/*** *** ********

NTP 279-8013-904
PVC establish Function

(Privileged This command is used to establish a permanent connection. The PVC will become
Command) effective immediately upon being set.
Reference Command
DISPLAY pvc
Cancel Command
PVC delete, PVC flush, SHOW pvc
Setting Procedure
1. Use the SET profile command to set the profile of the traffic type used in
PVC.
2. If you wish to use the shaper function, set the shaper by executing the
SET shaper command (shaper cannot be used in Buffer 1).
3. Use the DISPLAY interface command to check the effective bit length
of VPI/VCI. (An error will result if a VPI/VCI in excess of this bit length is
specified.)
4. Establish a PVC by executing the PVC establish command. (An error will
result if there is insufficient remaining band.)
NOTE To route only on the Virtual Path Identifier (VPI), set the VCI to 0.
Format
HOSTNAME# PVC establish P1 P2 P3 P4 P5 P6 P7 P8 P9
P10 P11 {P12~14}
Format Explanation
P1 : Connection type (0 (bi-directional), 1 (multipoint) or 2 (uni-directional))
P2 : Traffic type (0 (abr), 1 (cbr), 2 (nrt-vbr), 3 (rt-vbr) or 4 (ubr))
P4 : Ingress VPI number (0~4095)
P5 : Ingress VCI number (0, 32~16383)
P7 : Egress VPI number (0~4095)
P8 : Egress VCI number (0, 32~16383)
P9 : (Ingress Egress) UPC mode (off(0) or 1~5)

NTP 279-8013-904
P10 : (Ingress Egress) shaper number (off(0) or 1~8)

P11 : Forward (Ingress Egress) profile name
P12 : (Egress Ingress) UPC mode (off(0) or 1~5)
P13 : (Egress Ingress) shaper number (off(0) or 1~8)
P14 : Backward (Egress Ingress) profile name
NOTE The shaper number must be fixed to "1" to use the Shaper function for the
multipoint connection.
If a shaper number is specified and no rate has been set by the set shaper
command, the process terminates abnormally.
The profile name must have been previously registered by executing the
set profile command.
Example
HOSTNAME> PVC establish 0 1 10 1 100 20 2 200 0 0 cbr 0 0 cbr
Output
In case of uni-directional:
Connection has been established.

Connection type : Uni-direction
Traffic type : ****
** ***/*** -> ** ***/*** *** *** *****
In case of bi-directional:

Connection type : Bi-direction
Traffic type : ****
** ***/*** -> ** ***/*** *** *** *****
<- ** ***/*** *** *** *****
In case of multipoint:

Traffic type : ****
** ***/*** -> leaf 0 ** ***/*** *** *** *****

NTP 279-8013-904
PVC flush Function

(Privileged This command is used to delete all the PVCs of each line.
Command) The command also deletes any leaf applied with a multipoint.
Format
HOSTNAME# PVC flush P1
Format Explanation
Example
HOSTNAME# PVC flush 01
Output
All connections on the line interface have been deleted.

NTP 279-8013-904
PVC remove Function

(Privileged This command is used to delete a PVC endpoint or leaf from a multipoint path.
Command) This command deletes one endpoint at a time. The incoming side setting specified
by this command must be the same as the incoming setting of the existing path.
The sequence of deletion may be different from the sequence in which the
endpoints were set.
Format
HOSTNAME# PVC remove P1 P2 P3 P4 P5 P6
Format Explanation
P1: Ingress line number (00~33)
P2: Ingress VPI number (0~4095)
P3: Ingress VCI number (0, 32~16383)
P4: Egress line number (00~33)
P5: Egress VPI number (0~4095)
P6: Egress VCI number (0, 32~16383)
Example
HOSTNAME# PVC remove 40 1 100 42 2 200
Output
***Connection endpoint has been removed.

Traffic type : ****
** ***/*** -> leaf 0** ***/*** *** *** *****
-> leaf 1** ***/*** - *** -
-> leaf 2** ***/*** - *** -

NTP 279-8013-904
RESET ? Function
(Privileged This command is used to display the help message for the RESET command.
Command)
Format
HOSTNAME# RESET ?
Output
slot Slot reset

switch Switch reset

NTP 279-8013-904
RESET slot Function

(Privileged This command is used to restart (reset) the line card.
Command)
Format
HOSTNAME# RESET slot P1
Format Explanation
Example
HOSTNAME# reset slot 3
Output

Slot 3 has been reset.
1
Slot reset is not executed.
Output Explanation
1. Slot number

NTP 279-8013-904
RESET switch Function

(Privileged This command is used to restart (reset) the entire switch, including the line cards.
Command)
Format
HOSTNAME# RESET switch {P1}
Format Explanation
P1 : Switch or slot
Output
HOSTNAME# reset switch

The system is coming up now.
If you want to enter boot program, push [ESC] key immediately.
If the [ESC] key is detected within 3 seconds, boot program is
loaded.
Otherwise, online program will be loaded from the flash memory.
System reset is not executed.

NTP 279-8013-904
ROUTE ? Function
(Privileged
This command is used to display the help message for the ROUTE command.
Command)
Format
HOSTNAME# ROUTE ?
Output
add Add route to static SVC routing table

delete Delete route from SVC static routing table
flush Delete all entries from SVC static routing table
resume Resume primary route

NTP 279-8013-904
ROUTE add Function

(Privileged This command is used to set an entry in the SVC static routing table. A static route
Command) is entered to associate an ATM address (usually another switch) with a specific port.
The routing table has a maximum of 128 entries.

NOTE
One address may be set to route to multiple ports, yet only one is active at any
given time. Should the active port fail, routing resumes on the next specified line.
Reference Command
DISPLAY route
Cancel Command
ROUTE delete, ROUTE flush
Format
HOSTNAME# ROUTE add P1 P2 P3 {P4~P16}
Format Explanation
P1 : Address Type (NSAP or E.164)
P2 : Destination Address
When P1 is NSAP, up to 40 characters (0~9, A~F, X)
When P1 is E.164, up to 16 characters (0~9, X)
P3 : 1st Choice line (00~33)
P4 : 1st TunnelingVPI (-, 0~4095)
P5 : 2nd Choice line (00~33)
P6 : 2nd TunnelingVPI (-, 0~4095) (- for no tunneling)
P7 : 3rd Choice line (00~33)
P8 : 3rd TunnelingVPI (-, 0~4095)
P9 : 4th Choice line (00~33)
P10 : 4th TunnelingVPI (-, 0~4095)

NTP 279-8013-904
NOTE
Enter - to default VPI.
Example
HOSTNAME# route add nsap 39100 00
Output
SVC route has been added.

NTP 279-8013-904
ROUTE delete Function

(Privileged This command is used to delete the specified entry from the SVC static routing
Command) table.
Format
HOSTNAME# ROUTE delete P1 P2
Format Explanation
P2 : Destination Address
When P1 is NSAP, up to 40 characters (0~9, A~F, X)
When P1 is E.164, up to 16 characters (0~9, X)
Example
HOSTNAME# route del nsap 39100
Output
SVC route has been deleted.

NTP 279-8013-904
ROUTE flush Function

(Privileged This command is used to delete all entries of the SVC routing table.
Command)
Format
HOSTNAME# ROUTE flush
Output
HOSTNAME# route flush

SVC routing table has been flushed.

NTP 279-8013-904
ROUTE resume Function

(Privileged This command is used to return the primary port of the static routing table to the
Command) initial status. If more than one port was specified for a given address with
ROUTE add command, and the initial port is not active, this resume command
will return routing to the first port specified that is active.
Format
HOSTNAME# ROUTE resume P1 P2
Format Explanation
P2 : Destination address
When P1 is NSAP, 40 characters max (0~9,A~F,X)
When P1 is E.164, 16 characters max (0~9,X)
Example
HOSTNAME# route resume nsap 39100
Output
SVC route priority has been initialized.

NTP 279-8013-904
SAVE (Privileged Function

Command) This command is used to save the configuration data to active and standby sides.
Configuration data that is not saved with this command will be lost when the power
is turned off, or when RESET is executed.
Format
HOSTNAME# SAVE
Format Explanation
Output
HOSTNAME# save
Do not push reset button until save finishes.
#########
[OK]
Output Explanation
Process result (OK/No Good (NG))

NTP 279-8013-904
SET ? (Privileged Function

Command) This command is used to display the help message for the SET command.
Format
HOSTNAME# SET ?
Output
HOSTNAME# set ?
atmsig Q.2931 parameters
boot Boot parameters
calledsoftpvp Called softpvp check flag
cdvt CDVT configuration
cevc Circuit emulation configuration
clock Clock mode
ether IP address of ethernet interface
iisp Crankback information
interface Line interface parameters
linestatus Administrative status
local Switch local configuration
loopback Line interface status
looptime Looptime switch
mib MIB information
nms NMS information
oamend OAM endpoint
pnni PNNI information
prompt Prompt information
scope Scope information
scroll Scroll lines
server Server IP address
shaper Shaping rate
sscop SSCOP parameters
svcline SVC line status of line interface
t309trg T309 when interface failure has occurred
telnetlimit Telnet session timeout
time System time

NTP 279-8013-904
SET atmsig Function

(Privileged This command is used to set Q.2931 signaling parameters.
Command) Before the parameters may be changed, the system lines must be "suspended" by
executing the SET svcline command. The parameter modification is valid after the
line is reset to "resume."
Reference Command
DISPLAY atmsig
Format
HOSTNAME# SET atmsig P1 {P2}
Format Explanation
P2 : VPI (0~4095) (0 is default)
Subsequent parameters can be set interactively.
Interactive Parameters
HOSTNAME# set atmsig 00 0

Interface (network|0 user|1)?
T301 (1-511,default=180)?
T303 (1-255,default=4)?
T308 (1-511,default=30)?
T309 (1-511,default=10)?
T310 (1-255,default=10)?
T313 (1-255,default=4)?
T316 (1-511,default=120)?
T317 (1-255,default=60)?
T322 (1-255,default=4)?
T397 (1-511,default=180)?
T398 (1-255,default=4)?
T399 (1-511,default=14)?
UNI version (UNI3.0|0 UNI3.1|1 UNI4.0|2,default=4.0)?
NOTE Value set before the modification is displayed as default value. (Default values
shown are the initial values). Timing parameters should only be changed by
knowledgeable administrators.
Output
Q.2931 parameters have been set.

NTP 279-8013-904
SET boot This command is used to set the BOOT mode of the ATM switch.
(Privileged Refer to DISPLAY boot command for details of each mode.
Command)
Reference Command
DISPLAY boot
Change Command
SET boot
Setting Procedures for Loading New Software

1. Set the IP address of the switch by executing the SET ether command.
2. Set the IP address and boot file name of the server and router by executing the
SET server command.
3. Save the settings of Step 1 and Step 2 by executing the SAVE command.
4. Set the mode by executing the SET boot command.
5. Enter the RESET switch command to boot the system.
Format
HOSTNAME# SET boot P1
Format Explanation
P1: Booting mode
Flash
Flash_up
Flash_up_save
Initialize
Initialize_save
Network
Network_save
Output
Boot mode has been set.
NOTE Following the next system reset, the specified boot location will be loaded.

NTP 279-8013-904
Software Download Procedure

1. Set Ethernet address of the ATM switch (SET ether).
2. Set TFTP server Ethernet address and directory/name of boot file
(SET server).
3. Save configuration (SAVE; configuration will be lost if not saved).
4. Set boot mode (SET boot; either initialize or network).
5. Reset the switch (RESET switch).
The ATM switch will locate the TFTP server, then the boot file. The boot file has a
listing that instructs the ATM switch where to find the software modules. If the boot
attempt is unsuccessful, the ATM switch will reset itself and boot from flash.
Example and Output
HOSTNAME# set ether 208.205.40.15.255.255.255.0

Ethernet IP address has been set.
HOSTNAME# set server 208.205.40.45.0.0.0.0 /2.5G/ver4_3/bootfile
Server configuration has been set.
HOSTNAME# save
configuration saved
HOSTNAME# set boot net
Boot mode has been set.
HOSTNAME# reset switch
System reset has been executed.

NTP 279-8013-904
SET Function
calledsoftpvp This command is used to switch the recognition standard of called SoftPVP.
(Privileged
Command) Reference Command
DISPLAY calledsoftpvp
Change Command
SET calledsoftpvp
Format
HOSTNAME# SET calledsoftpvp P1
Format Explanation
P1 : 0 (disable) or 1 (enable) (default = 0)
Output
Called softpvp check flag has been set.
NOTE If P1 is set to "0" (disable), then the recognition of called SoftPVP is assured.
However, the ATM switch will no longer recognize SoftPVP calls from Software
Version 5.1 or earlier.
If P1 is set to "1" (enable), the ATM switch will recognize called SoftPVPs
regardless of software version. However, their operation will not be assured.

NTP 279-8013-904
SET cdvt Function

(Privileged This command is used to set the Cell Delay Variation Tolerance (CDVT) value for
Command) each line or tunneling.
Reference Command
DISPLAY cdvt
Format
HOSTNAME# SET cdvt P1 P2 P3 P4 P5 P6 P7 P8 P9
Format Explanation
P1 : Port number (00~33)
P2: VPI
P3 : CDVT value for CBR (1-12000 s)
P4: CDVT value for rt-VBR (1-12000 s)
P5: CDVT value for nrt-VBR (1-12000 s)
P6: CDVT value for UBR (1-12000s)
P7: CDVT value for UPC-Mode 2 (1-12000 s)
NOTE Default CDVT value is 1000 s.

NTP 279-8013-904
Example
HOSTNAME# set cdvt ?

HOSTNAME# set cdvt 00 ?

0-4095 VPI
- Not applicable
HOSTNAME# set cdvt 00 - ?

1-12000 CDVTp for CBR[us]
- default=2000
HOSTNAME# set cdvt 00 - - ?

1-12000 CDVTp for rt-VBR[us]
- default=2000
HOSTNAME# set cdvt 00 - - - ?

1-12000 CDVTp for nrt-VBR[us]
- default=2000
HOSTNAME# set cdvt 00 - - - - ?

1-12000 CDVTp for UBR[us]
- default=2000
HOSTNAME# set cdvt 00 - - - - - ?

1-12000 CDVTs for UPC-Mode2[us]
- default=2000
HOSTNAME# set cdvt 00 - - - - - - ?

1-12000 CDVTs for UPC-mode3[us]
- default=2000
HOSTNAME# set cdvt 00 - - - - - - - ?

1-12000 CDVTs for UPC-mode4[us]
- default=2000
HOSTNAME# set cdvt 00 - - - - - - - - ?

<cr>
Output
CDVT parameters have been set.

NTP 279-8013-904
SET cevc Function

(Privileged This command is used to set circuit emulation (CE) information.
Command)
Reference Command
DISPLAY cevc
Delete Command
DELETE cevc
Setting Procedure
1. Set the interface of a line by executing the SET interface command.
2. Set the interface of a VC by executing the SET cevc command.
3. If profile is to be used, then set the profile of traffic type CBR by executing the
SET profile command. Here, set the PCR so it is larger than the PCR as
can be seen by CE line VCI executing the DISPLAY cevc command.
4. Use the PVC establish command to set traffic type to CBR, VPI to 0, and
shaper to "off" (fixed). Set VCI to the value specified in Step 2, set connection
type to a connection type other than "bi-directional" if "uni-directional" was
specified in Step 2, and set the profile to "-" (default; other than P-to-MP) or
to the profile specified in Step 3.
Format
HOSTNAME# SET cevc P1 P2 P3
Format Explanation
P2 : VCI
CE-DS1/E1 Port0 : 256~287
CE-DS1/E1 Port1 : 288~319
CE-DS1/E1 Port2 : 320~351
CE-DS1/E1 Port3 : 352~383
P3: Direction (bi-directional, up (STM->ATM), down (ATM->STM))

NTP 279-8013-904
The possible setting range of CDVT varies depending on the structured size and
partial fill size.
A series of time slots can be set by using hyphens (for example, 1-32).
The same time slot may not be set to different VCs.
In case of unstructured, VC is not fixed.
Overwrite is not possible with this command.
In case of bi-directional, the number of time slots must be the same for up and
down sides.

NTP 279-8013-904
In case of CE-DS1 structured (bi-directional):

up Timeslot (1-24)?
down Timeslot (1-24)?
up Partial Fill Size (0, xx-47)?
down Partial Fill Size (0, xx-47)?
(xxindicates number of Timeslot+1)
Condition data (0-255)?
CDVT (1-255)?
In case of CE-DS1 unstructured (bi-directional):

up Partial Fill Size (0, 33-47)?
down Partial Fill Size (0, 33-47)?
CDVT (1-255)?
In case of CE-DS1 structured (uni-directional):

Timeslot (1-24)?
Partial Fill Size (0, xx-47)?
CDVT (1-255)?
In case of CE-DS1 unstructured (uni-directional):

up Timeslot (2-16, 18-32)?
down Timeslot (2-16, 18-32)?
up Partial Fill Size (0, xx-47)?
down Partial Fill Size (0, xx-47)?
CDVT (1-255)?
NOTE CDVT is a setting only for the down side. When the uni-direction is up, no
CDVT is displayed. The unit of CDVT is 125 sec.
In case of bi-directional, the number of time slots need not be the same for up
and down sides.

NTP 279-8013-904
In case of CE-E1 structured (bi-directional):

Partial Fill Size (0, 33-47)?
CDVT (1-255)?
In case of CE-E1 unstructured (bi-directional):

up Partial Fill Size (0, 33-47)?
down Partial Fill Size (0, 33-47)?
CDVT (1-255)?
In case of CE-E1 structured (uni-directional):

Timeslot (2-16, 18-32)?
Partial Fill Size (0, xx-47)?
CDVT (1-255)?
In case of CE-E1 unstructured (uni-directional):

Partial Fill Size (0, 33-47)?
CDVT (1-255)?
NOTE CDVT is a setting only for the down side. When the uni-direction is up, no
CDVT is displayed. The unit of CDVT is 125 sec for structured and 165.8 sec
for unstructured.
In case of bi-directional, the number of time slots need not be the same for up
and down sides.
Output
Circuit Emulation connection has been set.

NTP 279-8013-904
SET clock Function

(Privileged This command is used to set the clock source mode.
Command) Master: When set to master, all the line cards synchronize transmitted data to the
self-running Master clock generated by the ATM switch.
Slave: When set to slave, all the line cards synchronize transmitted data to the clock
derived from the receive port specified by parameter P3.
Reference Command
DISPLAY clock
Format
HOSTNAME# SET clock P1 {P2 P3} {P4} {P5}
Format Explanation
P1 : Clock mode
Master (default)
Slave
P2~5: Line number (00~13)
NOTE When the clock mode is set to master, no other parameters may be set.
For slave mode, up to four clock source ports may be set. If the first port fails, the
next port will be used for the slave port.
Example
HOSTNAME# set clock sl 30 31 32 33

Clocking Mode:Slave
Slaveline Status
* 030 Good
031 Good
032 Failure
033 Failure

NTP 279-8013-904
Output
When set to master mode:
Clocking Mode: Master
If the slave system clock mode is selected:
Clocking Mode: Slave

Slave line Status
** **
1 2
Output Explanation
1. Line number
The clock sampling line in slave clock mode currently being used is identified
by an asterisk (*) at the left of the line number.
2. Line status (GOOD, Failure, AdminDown, Not installed, Not supported or
Diagnostics)
NOTE If the installed line package is removed and a different type of line package is
installed, the related lines will automatically be released from slave mode.

NTP 279-8013-904
SET configserver Function

(Privileged This command is used to add an ATM address of a LAN emulation configuration
Command) server. This table may have four entries. An end-user may retrieve these addresses
through ILMI and, in turn, use the address to locate the LECS.
Reference Command
DISPLAY configserver
Cancel Command
DELETE configserver
Format
HOSTNAME# SET configserver P1 P2
Format Explanation
P1 : LECS address table index (0~3)
P2 : ATM address (max. 40 char (0~9, a~f, A~F))
Example
HOSTNAME# set configserver 0
Output
Configuration server has been set.

NTP 279-8013-904
SET dlci Function

(Privileged
This command is used to change set data for each DLCI connection.
Command)
Setting Procedure
1. Check the interworking type of the specified line by using the
DISPLAY interface command.
2. Set the profile of the traffic type that is used for the connection by using the
SET frprofile command. (Specify same interworking type as that of the
line)
3. Use this command to set DLCI data.
Format
HOSTNAME# SET dlci P1 P2 P3
Format Explanation
P2: DLCI (16~991) (DLCI+16=VCI)
P3: Frame Relay Profile Name (up to 10 alphanumeric characters)
Output
DLCI interface xxx has been set.

1
Output Explanation
1. Line Number
Frame relay profile must be registered with SET frprofile in advance. The
NOTE
interworking type of the specified line has to be the same as that of the profile.

NTP 279-8013-904
SET ether Function

(Privileged This command is used to set the Ethernet IP address and subnet mask of the ATM
Command) switch PCMCIA Ethernet port LANcard (optional).
Reference Command
DISPLAY ether, DISPLAY network
Format
HOSTNAME# SET ether P1 P2
Format Explanation
P1 : Ethernet IP address (x.x.x.x (x=0~255))
P2 : Ethernet subnet mask (x.x.x.x (x=0~255))
Example
HOSTNAME# set ether 100.10.5.6 255.255.255.0
Output
Ethernet IP address has been set.
NOTE The Ethernet port is used for "telnetting" into the ATM switch as a MAT, and for
software downloads and configuration storing to/from a TFTP server.

NTP 279-8013-904
SET froam Function

(Privileged
This command is used to set the OAM endpoint of f5 (VC level) between frame
Command) relay and ATM.
Format
HOSTNAME# DELETE froam P1 P2 P3 P4 P5 P6
Format Explanation
P3: VCI of Point 1 (32~16383)
P6: VCI of Point 2 (32~16383)
Output
FROAM connection has been set.
The connection specified by this command must have been registered using the
NOTE
PVC establish command in advance. The connection cannot be established
for the same line.

NTP 279-8013-904
SET frprofile Function

(Privileged This command is used to set the profile for frame relay.
Command)
Format
HOSTNAME# SET frprofile P1
Format Explanation
P1: Name of the profile for frame relay (up to 10 alphanumeric letters)
Interworking (network|0 service|1)?
CIR (1-1984[kbps])?
DE to CLP mapping mode (Mode1|0 Mode2|1)?
CLP value (0 or 1)?
(Can be set only if Mode2 had been selected for DE to CLP mapping mode)
CLP to DE mapping mode (Mode1|0 Mode2|1)?
DE value (0 or 1)?
(Can be set only if service had been selected for interworking and Mode2
for CLP to DE mapping mode)
Protocol encapsulation mode (transparent|0 translation|1)?
(Can be set only if service had been selected for interworking)
Congestion indication (forward) mode (Mode1|0 Mode2|1)?
(Can be set if service is selected for interworking)
Output
FR profile data has been set.

NTP 279-8013-904
SET iisp Function

(Privileged This command is used to set IISP mode.
Command) Swaproute enables the operation of crankback. If a switch, while attempting
to signal a connection down one path of a multi-directional network, rejects the
connection, the signaling path will backtrack and attempt to branch down an
alternate path, bypassing the blocked switch.
Reference Command
DISPLAY iisp
Format
(1)HOSTNAME# SET iisp loopcheck P1 {P2}
(2)HOSTNAME# SET iisp splithorizon P1 {P2 P3}
(3)HOSTNAME# SET iisp swaproute P1 P2
Format Explanation (1)

P1 : Action (on or off)
P2 : Hop count (1~64 (default=7))

P3 : VPI (0~4095)
NOTE If a line number is specified, VPI cannot be defaulted.

P2 : Resume timer value (1~20 min. (default=10))
Example (1)
Loop check ******

1

NTP 279-8013-904
Example (2)
Split Horizon ******

1
Example (3)
Swapping ******
1
Output Explanation
1. enabled = on
disabled = off

NTP 279-8013-904
SET ilmi Function

(Privileged This command is used to set the VPI/VCI path (0/16) for enabling ILMI (Interim
Command) Local Management Interface). This command also sets the time allowed for
attempting address registry, the timer for performing a retry when registry fails, and
the cycles at which the address registered for ILMI is checked.
ILMI and Functions

Upon initial connection of end-user equipment, pertinent information is swapped
between the two endpoints of the ILMI connects (PVCs on a line card port). This
information will be useful for signaling, once ILMI registration is complete.
Parameters such as valid VPI/VCI bits, UNI Version, maximum number of possible
connections, LECs addresses, are discovered. Also, the switch adds to its route
table an entry for the end users address and associated port.
It is recommended that you learn the pertinent configuration data of a connected
end user.
Reference Command
DISPLAY ilmi
Cancel Command
DELETE ilmi
Format
HOSTNAME# SET ilmi P1 {P2} {P3} {P4} {P5} {P6} {P7}
Format Explanation
P1 : Connection / process (00~33)
P3 : VPI (0~4095) (default=0)
P4 : VCI (0~16383) (default=16)
P5 : Timer value (1~511(s): default=10(s))

P6 : Times of retry (1~511: default=60) If P1 is connection
P7 : Keepalive (1~511(s): default=60(s))
If P1 is process, P5 is:
0/off ILMI process flag off
1/on ILMI process flag on

NTP 279-8013-904
Example
HOSTNAME# set ilmi ?

connection Control connection
process Process flag information
HOSTNAME# set ilmi process ?

HOSTNAME# set ilmi process 00 ?

0-4095 VPI
HOSTNAME# set ilmi process 00 0 ?

0|off ILMI process flag OFF
1|on ILMI process flag ON
HOSTNAME# set ilmi process 00 0 1 ?

<cr>
HOSTNAME# set ilmi connection ?

HOSTNAME# set ilmi connection 00 ?

0-4095 VPI
<cr> default=0
HOSTNAME# set ilmi connection 00 0 ?

1-16383 VCI
<cr> default=16
HOSTNAME# set ilmi connection 00 0 16 ?

1-511 Timeout[sec]
<cr> default=1[sec]
HOSTNAME# set ilmi connection 00 0 16 1 ?

1-511 Times of retrial
<cr> default=4
HOSTNAME# set ilmi connection 00 0 16 1 4 ?

1-511 Keepalive timer[sec]
<cr> default=5[sec]
HOSTNAME# set ilmi connection 00 0 16 1 4 5 ?

<cr>
Output
ILMI connection has been set.

NTP 279-8013-904
SET interface Function

(Privileged This command is used to register a line, provided a line card is installed and no
Command) connection is set in the specified line.
Format
HOSTNAME# SET interface P1
Format Explanation
Procedures for Setting the Line Interface

1. Delete connections (PVC, Soft PVP), if any are established.
2. Suspend the line by executing the SET svcline command.
3. Delete signaling connections by executing the DELETE signaling
command.
4. Delete ILMI connections by executing the DELETE ilmi connection
command.
5. Delete PNNI connections by executing the DELETE pnni connection
command.
6. Delete IP routing connections by executing the DELETE iproute
command.
7. Enter the SET interface command.
8. Establish the connections by executing the SET ilmi connection
command, SET signaling command, SET pnni connection
command, and SET iproute command.
9. Resume the line by executing the SET svcline command.
10. If any connections were deleted in Step 1, then re-establish as necessary.
NOTE

NTP 279-8013-904
Interactive Parameters for the Interfaces
For OC-3c, OC-12c and STS-3c/STM1(COAXIAL):

Interface (pri_uni/0 pri_nni/1 pub_uni/2)?
Forum/ITU (forum/0 itu/1)?
IDLE Cell (unassigned/0 idle/1)?
Valid VPI
Valid VCI
VPI filter mask range (0-12[bit], default=Valid VPI)?
VCI filter mask range (x-16[bit], default=Valid VCI)?
Valid VPI: (0-8)[bit] for UNI interface; (0-12[bit]) for NNI interface
NOTE
Valid VCI: (0-14)[bit] for UNI interface; (0-14)[bit]) for NNI interface
For 100M-TAXI:
Valid VPI
Valid VCI
VCI filter mask range (0-16[bit], default=Valid VCI)?
NOTE
For DS3:
Valid VPI
Valid VCI
Frame mode (cbit/0 m23/1)?
Cell mapping (plcp/0 direct/1)?
Scramble (off/0 on/1)?
LBO (hi/0 lo/1)?
NOTE

NTP 279-8013-904
For E3:
Valid VPI
Valid VCI
Frame mode (g832(g804)/0 g751/1)?
NOTE
For DS1, E1:

Valid VPI
Valid VCI
NOTE Valid VPI: (0-8)[bit] for UNI interface; (0-12[bit]) for NNI interface
LBO for DS1: (0-110/0 110-220/1 220-330/2 330-440/3 440-550/4 550-660/5 660/6
For J2:
Interface(pri_uni/0 pri_nni/1 pub_uni/2)?
Valid VPI
Valid VCI
VPI filter mask range(0-12[bit], default=Valid VPI)?
VCI filter mask range(0-16[bit], default=Valid VCI)?
Line rate(6M/0 4.5M/1 3M/2)?
Slot * is reset. Are you sure? [Y or N]

NTP 279-8013-904
For Primary:
Interface(pri_uni/0 pri_nni/1 pub_uni/2)?
TTC/ITU-T (ttc/0 itu_t/1)?
Valid VPI
Valid VCI
VPI filter mask range(0-12[bit], default=Valid VPI)?
VCI filter mask range(0-16[bit], default=Valid VCI)?
Line rate(1.5M/0 1.1M/1 768K/2 512K/3 384K/4 256K/5 192K/6)?

NTP 279-8013-904
Changing a CE Line Interface

1. Delete all connections (PVCs, Soft PVPs) from the line, if any.
2. Delete all cevc settings on the line by executing the
DELETE cevc command.
3. Change the interface of a line by executing the SET interface command.
4. Set cevc and establish a connection as necessary.
Interactive Parameters for the CE Line Interfaces
For CE-DS1:
Service (Unstructured/0 structured/1)?
LBO (0-110/0 110-220/1 220-330/2 330-440/3 440-550/4 550-660/5 660/6)?
For structured service:

CAS mode (Basic/0 CAS/1?
For FR-DS1:
Interface (uni/0 nni/1?
FR Forum/ITU_T/ANSI (fr_forum/0 itu_t/1 ansi/2)?
Interworking (network/0 service/1)?
LBO (0-110/0 110-220/2 220-330/2 330-440/3 440-550/4 550-660/5)?
Fractional type (unchannelized/0 fractional/1)?
For fractional:
Fractional set (1-24)?
Output
Line Interface xx has been registered.

1
Output Explanation
1. Line Number
NOTE The range of ValidVCI settings varies depending on the bit count specified by
ValidVPI.

NTP 279-8013-904
Output
Line Interface *** has been registered.

1
Output Explanation
1. Line number
NOTE The permissible setting range of valid VCI differs depending on the bit count
specified for valid VPI.

NTP 279-8013-904
SET iproute Function

(Privileged This command is used to set IP routing information. The parameters differ
Command) depending on the interface type.
Reference Command
DISPLAY iproute
Cancel Command
DELETE iproute
Format
HOSTNAME# SET iproute ec0 P2 P3 P4
HOSTNAME# SET iproute atm0 P2 P3 P5 P6 P7
Format Explanation
P1 : Interface type (atm0 or ec0)
P2 : Destination type (net or host)
P3 : Destination IP address (x.x.x.x (x=0~255)) or default router
P4 : Router IP address (x.x.x.x (x=0~255)) (set only when ec0 is specified)
P5: Line number (00~33) (set only when atm0 is specified)
P6 : VPI (0~4095) (set only when atm0 is specified)
P7 : VCI (0~16383) (set only when atm0 is specified)
NOTE Ec0 Used to designate a route for Telnet, NMS, or software downloaded over
Ethernet that must traverse a router.
ATM0- Used to designate a route for Telnet, NMS, or software downloaded over
an ATM interface.
Example
HOSTNAME# set iproute ec0 net default 10.5.6.1
Output
IP route information has been set.

NTP 279-8013-904
SET linestatus Function

(Privileged This command is used to change the operating status of the line.
Command) By specifying the down parameter, all operation for that port is disabled. The
signaling/ilmi/pnni/line error operation on the specified line is stopped.
Reference Command
DISPLAY line
Format
HOSTNAME# SET linestatus P1 P2
Format Explanation
P2 : Line status (down or up)
Output
If the line is not clock sampling line:
Linestatus has been set.
If the line is clock sampling line:

Clocking mode has been changed.(Slaveline:**)
1
If the line is maintenance PVC line:

Linestatus not registered.
If there is a maintenance PVC on the specified line and if P2 is down:
This will disable atm0 iproute configuration.

Are you sure ? [Y or N]

NTP 279-8013-904
If Y is entered:
Line status has been set.
If N is entered:
Line status not registered.
Output Explanation
1. Line number
NOTE If the line for which "down" is specified is the only line that can be selected
among the slave lines of the clock, the setting will result in a command error since
the clock cannot be sampled.

NTP 279-8013-904
SET local Function

(Privileged This command is used to set the host name, ATM interface IP address, IP mask, and
Command) ATM prefix information of the ATM switch.
Reference Command
DISPLAY network
Change Command
SET local
Format
HOSTNAME# SET local P1 P2 P3 P4
Format Explanation
P1 : Host name (up to eight alphanumeric characters)
P2 : ATM IP Address (x.x.x.x (x=0~255))
P3 : Mask value of ATM IP Address (x.x.x.x (x=0~255))
P4 : ATM prefix node ID (up to 26 hexadecimal alphanumeric characters). If less
than 26 characters, the remaining spaces will automatically be padded with
zeros.
Example
HOSTNAME# set local HOSTNAME 10.1.1.3 255.255.255.0 390102

HOSTNAME# show net
Output
Local configuration has been set.
NOTE The ATM IP address must be on a separate IP network from the Ethernet address.

NTP 279-8013-904
SET loopback Function

(Privileged This command is used to set the loopback on the line interface.
Command)
Reference Command
DISPLAY line
Change Command
SET loopback
Format
HOSTNAME# SET loopback P1 P2
Format Explanation
P2 : Line status ( normal, local or remote)
NOTE local and remote indicate loopback
Output
If there is a maintenance PVC on the specified line and if P2 is down:
This will disable atm0 iproute configuration.

Are you sure ? [Y or N]
If Y is entered:
Line interface *** has been set.
If N is entered:
Line interface *** not registered.
If other than the above is entered:
Line interface *** has been set.

Line interface *** not registered.
1
Output Explanation
1. Line number
NOTE If the specified line is 100M-TAXI, it cannot be set to remote.

NTP 279-8013-904
SET looptime Function

(Privileged This command is used to set the per port clock recovery. A port with looptime set
Command) to "on" will recover the receive port clock and synchronize the transmit clock to it.
The transmit port "slaves" its clock to the clock recovered from the receive port.
This has priority over "clock master or slave."
Reference Command
DISPLAY looptime
Format
HOSTNAME# SET looptime P1 P2
Format Explanation
P1 : Looptime (on (1) or off (0))
Output
Line interface ** has been set.

1
Output Explanation
1. Line number
NOTE No loop time may be set for 100M-TAXI.

Loop time cannot be set while the switch and line are being diagnosed.
Lines for which loop time has been set cannot be connected to each other.
Only one line may be set for DS/E3 loop time.

NTP 279-8013-904
SET mib Function

(Privileged This command is used to set the MIB syscontact and syslocation found in fields by
Command) the SHOW net command. This command merely sets two text strings for simple
user information.
Reference Command
DISPLAY network
Format
HOSTNAME# SET mib P1 P2
Format Explanation
P1 : Manager (up to 32 alphanumeric characters)
P2 : Installation location (up to 32 alphanumeric characters)
Example
HOSTNAME# set mib "NEC 1-800-832-6632" "Irving, Texas"
Output
MIB information has been set.
NOTE You may enter the information for both parameters in one command line by using
double quotes.
Example
HOSTNAME# set mib "Nortel Networks" Texas

HOSTNAME# show net
.
.
.
syscontact: Nortel Networks
syslocation: Texas
.
.
.

NTP 279-8013-904
SET nms Function

(Privileged This command is used to set the NMS information. Up to four (4) NMSs can be set.
Command)
Reference Command
DISPLAY network
Cancel Command
DELETE nms
Setting Procedure
1. To set the information via ATM, set the ATM IP address of the switch by
executing the SET local command. To set the information via Ethernet, set
the Ethernet IP address by executing the SET ether command.
2. If the subnet is different, set the IP routing by executing the SET iproute
command.
3. Register the NMS by executing the SET nms command.
Format
HOSTNAME# SET nms P1 P2 P3 P4
Format Explanation
P1 : NMS number (0~3)
P2 : IP Address (x.x.x.x (x=0~255))
P3 : Community name (up to 16 alphanumeric characters)
P4 : Access right (read-only (0) or read-write (1))
Output
NMS information has been set.

NTP 279-8013-904
SET oamcon Function

(Privileged This command is used to set the connecting point of a connection for transferring
Command) an alarm by OAM cell (alarm cell).
Reference Command
DISPLAY oamcon
Cancel Command
DELETE oamcon
Format
(1) HOSTNAME# SET oamcon f4 P1 P2 P3 P5 P6
(2) HOSTNAME# SET oamcon f5 P1 P2 P3 P4 P5 P6 P7
NOTE In f4 mode, it is not necessary to specify VCI value.

Format Explanation
P1: Point type
(segcon or 0 if the switch is a connecting point in the Segment flow)
(endcon or 1 if the switch is a connecting point in the End-to-End flow)
P3 : Ingress VPI (0~4095)
P4 : Ingress VCI (32~16383) [Not required for f4.]
P7 : Egress VCI (32~16383) [Not required for f4.]
Example
HOSTNAME# set oamcon f5 1 23 3 35 51 2 33
Output
OAM connecting point has been established.
NOTE Connections specified by this command must be previously registered by

executing the PVC establish command.

NTP 279-8013-904
SET oamend Function

(Privileged This command is used to set the endpoint of a connection for transferring an alarm
Command) by OAM cell (alarm cell).
Reference Command
DISPLAY oamend
Format
HOSTNAME# SET oamend P1 P2 P3 P4 {P5}
Format Explanation
P1 : Mode (f4 (VP level) or f5 (VC level))
P2 : Point type
(segend or 0 if the switch is an endpoint in the Segment flow)
(endend or 1 if the switch is an endpoint in the End-to-End flow)
NOTE When P1 is f5, specifying endend results in an error.

P4 : VPI (0~4095)
P5 : VCI (32~16383 (defaulted when the mode is f4))
Output
OAM endpoint has been established.
NOTE Connections specified by this command must be previously registered by

executing the PVC establish command.

NTP 279-8013-904
SET oamf5end Function

(Privileged
This command is used to set an OAM endpoint at f5 (VC level). The endpoint in
Command) f5 end-to-end mode supports the OAM loopback cell receiving process.
Format
HOSTNAME# SET oamf5end P1 P2 P3
Format Explanation
P2: VPI (0~4095)
P3: VCI (32~16383)
Output
OAM f5end endpoint has been set.

NTP 279-8013-904
SET pnni Function

(Privileged This command is used to enable PNNI connection.
Command)
This command sets a path to exchange the network topology, link status, and other
network information between the switches. Using this information, the switch
creates a dynamic routing table and refers to it during routing between the Private
Network-to-Network Interfaces (P-NNIs).
If the private NNI interface type has been set by the SET interface
command, the routing path (0, 18) is automatically set during system startup.
One or more PNNI paths can be set for a single physical line. However, only a single
PNNI path can be set for a single VPI.
1. To set the reachable address of PNNI:
Format
HOSTNAME# SET pnni address
PNNI>P1 P2 P3 P4 P5 P6 P7 {P8} {P9}
This sets a reachable address for PNNI. Enter SET pnni address to enter the
edit mode. While in the edit mode, the PNNI> prompt is displayed. Exit edit mode
by entering a period (.) The reachable address information of PNNI can be
displayed by entering the DISPLAY pnni address command. Internal
addresses are set for end-user devices that do not support ILMI registration.
External addresses are set for IISP attached switches.
Format Explanation
P1 : Process type (either Add or Change. All parameters other than length,
reachable address, and address type may be changed.)
P2 : Address type (Internal or Exterior)
P3 : SCOPE (0~104) (limits the broadcast domain. 0 = no limit.)
P4 : Effective bit count of reachable address (0~160)
P5 : Reachable address (up to 40 characters 0~9, A~F, a~f)
P7 : VPI (0~4095
P8 : Content of transit network ID data (effective only when Exterior is specified
for the address type) (0-127) <hexadecimal value>
P9 : Identifiers of the networks that will be passed through to reach the address.
NOTE These addresses, internal and external, will be broadcast, depending on scope,
to all nodes in the network.

NTP 279-8013-904
Example
HOSTNAME# set pnni address

PNNI>
PNNI> add ext 0 12 490 02 0
PNNI>.
HOSTNAME#
Output
PNNI reachable address has been set.

NTP 279-8013-904
2. To set the architectural variables of PNNI:
Format
HOSTNAME# SET pnni architectural P1 P2 P3 P4 P5 P6
P7 P8
This sets the timer/value parameters of PNNI. Information on PNNI's architectural
variable can be displayed by executing the DISPLAY pnni architectural
command.
Format Explanation
P1: Minimum transmission interval of Hello (1~120 second(s))
P2: Transmission interval of Hello (1~120 second(s))
P3: Transmission interval of database summary packet (5~120 second(s)) and
communication interval of PTSE request packet
P4: Minimum transmission interval of PTSE (1~120 second(s))
P5: Communication and retransmission interval of PTSE (5~120 second(s))
(One-fifth of this time setting becomes the PTSE response delay time.)
P6: Ring down recognition time (1~225 second(s))
P7: Percentage at which average cell rate change is notified (1~99%)
P8: Minimum value at which average cell rate change is notified (1~99%)
Example
HOSTNAME# set pnni arch 1 15 15 1 15 120 50 3
Output
PNNI architectural variables have been set.

NTP 279-8013-904
3. To set the virtual path of PNNI:
Format
HOSTNAME# SET pnni connection P1 {P2} {P3} {P4} {P5}
{P6}
This sets the path of PNNI. Information on PNNI's connection can be displayed by
executing the DISPLAY pnni connection command.
Format Explanation
P2 : VPI (0~4095, default=0)
P3 : VCI (1~16383, default=18)
P4 : Administrative weight (0~50400, default=5040)
Weight for cost calculation in link selection
P5 : Aggregation token (0~225, currently fixed to 0)
Value that decides the number of logical link divisions between LGNs in the
logical layer
P6 : UBR Best effort separate band (0~1412830)
Bandwidth secured for UBR
Example
HOSTNAME# set pnni conn 00
Output
PNNI connection has been set.

NTP 279-8013-904
4. To set the routing type of PNNI:
Format
HOSTNAME# SET pnni method P1
This sets the routing type of PNNI. "Hop by hop" is performed by IISP's routing
method and "source" is routed according to the DTL prepared by the routing unit
of PNNI 1.0. Information on PNNI's routing type can be displayed by executing the
DISPLAY pnni method command.
Format Explanation
P1 : Routing type ("HOP BY HOP" or "SOURCE")
Example
HOSTNAME# set pnni conn 00
Output
PNNI routing method has been set.

NTP 279-8013-904
5. To set the node information of PNNI:
Format
HOSTNAME# SET pnni nodal P1 P2
Because of the recursive nature of PNNI, each hierarchical level has a repeated set
of parameters. The software currently limits PNNI to three (3) levels of hierarchy.
After the initial command line is entered for number of levels and peer-group-leader
(PGL) election participation, subroutine values will be requested. PGL and Logical
Group Node (LGN) parameters are generally defaulted.
Format Explanation
P1 : Number of hierarchal levels (1~3)
P2 : Peer Group Leader (PGL) flag ("1" if able to participate in peer group leader
election)
NOTE Subsequent parameters can be set interactively.

Subsequent parameters:
-Hierarchy (, 0 - 104)?
Level number:
-Restricted transit bit (on|1 off|0)?
Through switch SVC restriction. Restricted if "on," not restricted if "off."
-Restricted branching bit (on|1 off|0)?
Judgement flag to restrict whether to serve as a branching point upon P-to-MP.
Restricted if "on," not restricted if "off."
-Leadership priority (0 - 255)?
Priority of becoming the PGL. Not selected as PGL if set to "0." The higher the
value, the greater the priority.
-Peer group ID (, up to 28 hexadecimal characters)?
ID of the PG to which every node must have to join. Automatically set when
defaulted.
-LGN ID (, up to 44 hexadecimal characters)?
PNNI logical node ID. Automatically set when defaulted.

NTP 279-8013-904
Example
HOSTNAME# set pnni nodal 1 1
Hierarchy 1
Level indicator (0-104)? 12

Restricted transit bit (0|off,1|on)? 0
Restricted branching bit (0|off,1|on)? 0
Leadership priority (1-255)? 100
Peer group ID (up to 28 hexadecimal characters)?
LGN ID (up to 44 hexadecimal characters)?
PNNI node information have been set.
HOSTNAME#
Output
PNNI node information has been set.

NTP 279-8013-904
SET profile Function

(Privileged This command is used for setting the profile that is requested upon setting PVC and
Command) soft PVP. These parameters are for policing if enabled in PVC establish.
command.
Reference Command
DISPLAY profile
Cancel Command
DELETE profile
Format
HOSTNAME# SET profile P1 P2
Format Explanation
P1 : Traffic type (0(abr), 1(cbr), 2(nrt-vbr), 3(rt-vbr) or 4(ubr))
P2 : Profile name (up to ten alphanumeric characters)
Example
HOSTNAME# set profile 1 mycbr
PCR (1-1412830 [cells/s])?

Peak cell rate
SCR (1-1412830 [cells/s])?

Sustainable cell rate
MBS (1-1412830 [cells])?

Maximum burst size
EPD (off/0 on/1)?

EPD function flag

NTP 279-8013-904
Output
Profile data has been set.
Profile name :**********

Traffic type :*******
Peak cell rate [cell/s] :*******
Sustainable cell rate [cell/s] :*******
Maximum burst size [cell] :*******
EPD :***

NTP 279-8013-904
SET prompt Function

(Privileged This command is used to set the prompt type. This setting is not included in the
Command) configuration data; therefore the prompt type is returned to the default prompt type
when the system is restarted.
Change Command
SET prompt
Format
HOSTNAME# SET prompt P1
Format Explanation
P1 : Prompt type (host or 1, time or 2, all or 3)
Output
This prompt appears when "host" or "1" is specified (host name prompt).
HOSTNAME# ..........
This prompt appears when time or 2 is specified (time prompt).
hh:mm:ss:#..........
This prompt appears when all or 3 is specified (host name and time prompt).
HOSTNAME hh:mm:ss#..........

NTP 279-8013-904
SET scope Function

(Privileged This command is used to change the scope mapped to each hierarchical level of
Command) PNNI.
Reference Command
DISPLAY scope
Change Command
SET scope
Format
HOSTNAME# SET scope
Hierarchy1 : UNI scope (xx~xx)?
Hierarchy2 : UNI scope (xx~xx)?
Output
PNNI mode scope information has been set.
NOTE The scope must be mapped with the SET pnni nodal command in advance.

NTP 279-8013-904
SET scroll Function

(Privileged This command is used to set the number of lines displayed on the MAT screen. If
Command) the P1 parameter is set to zero, displayed lines will continue being displayed until
completion.
Reference Command
DISPLAY scroll
SHOW scroll
Format
HOSTNAME# SET scroll P1
Format Explanation
P1 : Number of lines displayed on MAT (0~49)
Example
HOSTNAME# set scroll 40

Scroll filter: On
Output
Scroll filter: ***

1
Output Explanation
1. Scroll control (on or off)

NTP 279-8013-904
SET server Function

(Privileged This command is used to set TFTP server IP address, default router IP address and
Command) name of boot file. The TFTP server is used for system software download and
system configuration backup.
Reference Command
DISPLAY server
Format
HOSTNAME# SET server P1 {P2 P3}
Format Explanation
P1 : Server IP address (x.x.x.x (x=0~255))
P2 : Default router IP address (x.x.x.x (x=0~255)) 0.0.0.0 if no router present
P3 : Boot file name (up to 127 characters) and directory
Example
HOSTNAME# set server 10.5.3.4 0.0.0.0 2.5G/bootfiles/boot.txt
NOTE If the boot command is set to network or initialize, and the switch is
reset, it will attempt to connect to the TFTP server and load software located
there. If the backup or install commands are used, the switch will attempt to
store/retrieve configuration information.
Output
Server configuration data has been set.

NTP 279-8013-904
SET shaper Function

(Privileged This command is used to set a shaping rate.
Command) Only PCR is set for CBR connections. PCR, SCR, and MBS are set for other traffic
type connections.
Reference Command
DISPLAY shaper
Cancel Command
DELETE shaper
Format
HOSTNAME# SET shaper P1 P2 P3 {P4} {P5}
Format Explanation
P1 : Line number (ATM 2.5 Gbps switch)
P3 : PCR (cell/s) (1~1412830)
P4 : SCR (cell/s) (1~1412830)
P5 : MBS (cell)
Output
Shaping rate has been set.
NOTE For PCR and SCR the maximum range specified is for an OC-12 interface. For a
OC-3 or UTP-5 interface, the maximum is actually 353207.
If the specified rate cannot be set due to the limited hardware capacity, an
approximate value is selected and set automatically. A PCR or SCR exceeding the
physical rate cannot be set. Also, the following requirement must be satisfied:
PCR >= SCR & PCR >= MBS

NTP 279-8013-904
SET signaling Function

(Privileged This command is used to set the signaling path (0, 5).
Command)
Reference Command
DISPLAY signaling
Cancel Command
DELETE signaling
Format
HOSTNAME# SET signaling P1 {P2} {P3}
Format Explanation
P2 : VPI (0~4095) (default=0)
P3 : VCI (1~16383) (default=5)
Output
Signaling connection has been set.
NOTE Signaling will not be active if it has been suspended by the SET svcline
command.
To set a signaling connection whose VPI is 1 or greater, it is necessary to set the

tunneling with that VPI in advance.
Before changing the VCI with this command, suspend the operation by executing
the SET svcline command, delete signaling connections by executing the
DELETE signaling command, and reset the connection. Then resume the
operation by executing the SET svcline command to validate the change.

NTP 279-8013-904
SET sscop Function

(Privileged This command is used to set the SSCOP parameters of ATM signaling for the
Command) signaling connection set with the SET signaling command. These values
should rarely be changed unless the administrator is fully aware of values.
Reference Command
DISPLAY sscop
Format
HOSTNAME# SET sscop P1 P2
Format Explanation
P2: VPI (0~4095)
Setting Procedure
1. Disable signaling by executing the SET svcline command.
2. Set the parameters by executing the SET sscop command.
3. The parameters become effective when the operation is resumed by executing
the SET svcline command.
MaxCC (1-255, default=4) ?

TimerCC (1-255, default=1) ?
Timer Keepalive (1-255, default=30) ?
Timer NORESPONSE (1-255, default=10) ?
Timer POLL (1-255, default=1) ?
MaxPD (1-255, default=10) ?
MaxSTAT (1-255, default=4) ?
clear_buffers (Yes No, default=Yes) ?
NOTE The value set before modification is displayed as the default value. (Default values
shown above are the initial values.)
Output
SSCOP parameters have been set.
NOTE Before the parameters are set again by this command, the system lines must be
suspended by executing the set svcline command. The parameter
modification is valid after the line is reset to "resume."

NTP 279-8013-904
SET svcline Function

(Privileged This command is used to set the signaling status; suspended or resume.
Command) When the suspend command is entered, the SVC of the related line is
disconnected and all subsequent signaling messages are ignored. The SVC
functions are resumed by setting the line to resume.
Reference Command
DISPLAY svcline
Format
HOSTNAME# SET svcline P1 P2 P3
Format Explanation
P2 : VPI (0 ~ 4095)
P3 : SVC Status (suspend or resume)
NOTE suspend : suspends signaling function
resume : resumes signaling function
Output
SVC status of the line interface **: ***

1 2
Output Explanation
1. Line number
2. SVC status

NTP 279-8013-904
SET t309trg Function

(Privileged This command is used to set the timing of recognizing signaling line fault
Command) separately from T309.
Reference Command
DISPLAY t309trg
Change Command
SET t309trg
Setting Procedure
1. If the line is active, suspend signaling of a line or VPI by executing the
SET svcline command.
2. Set the parameters by executing this command.
3. The parameters become effective when the operation is resumed with the SET
svcline command.
Format
HOSTNAME# SET t309trg {P1}
Format Explanation
P1 : Time value (1~511[sec], T309 is used if defaulted)
Output
Timing has been set.
NOTE Before the parameters are set again by this command, the system lines must be
suspended with the SET svcline command. The parameter modification is
valid after the line is set to resume.

NTP 279-8013-904
SET telnetlimit Function

(Privileged This command is used to set the time limit of a Telnet session.
Command)
Reference Command
DISPLAY telnetlimit
Format
HOSTNAME# SET telnetlimit P1
Format Explanation
P1: Time limit to forced disconnection of the session after the last input/output
(0~32767 minutes).
NOTE Forced disconnection will be disabled if the time limit is set to 0.
Output
Telnet time-limit has been set.

NTP 279-8013-904
SET time Function

(Privileged This command is used to set the system date and time.
Command)
Reference Command
DISPLAY time
Format
HOSTNAME# SET time P1 P2
Format Explanation
P1: Date (YY-MM-DD)
Year: 0-99 (the last two digits of the year)
Month: 1-12
Day: 1-31
P2: Time (hh:mm:ss)
Hour: 0-23
Minute: 0-59
Second: 0-59
NOTE Split the date with - and the time with :
Example
HOSTNAME# set time 97-08-18 15:45:22
Output
System Timer has been set.

YY-MM-DD hh:mm:ss
NOTE YY-MM-DD indicates the year, month, and day of the month.
hh:mm:ss indicates the hour, minute, and second.
Example
January 10, 1999 is set as: 99-01-10
2:30pm and 15 seconds is set as: 14:30:15

NTP 279-8013-904
SET tunneling Function

(Privileged This command is used to set tunneling connection information.
Command)
Reference Command
DISPLAY tunneling
Setting Procedure
1. Choose a VPI path for tunneling; then issue the set tunneling, signaling, ILMI
and/or PNNI paths with the chosen VPI.
2. Enter the SET tunneling command.
Follow the steps below to set signaling and ILMI.
3. Establish tunneled signaling connection by executing the SET signaling
command to the chosen tunneling VPI.
4. If necessary, change the UNI Version, using SET atmsig/sscop.
5. Set the ILMI tunneling connection by executing the
SET ilmi connection command to the chosen tunneling VPI.
6. Resume the line (or VPI specification) using SET svcline command.
7. If using IISP, set the appropriate routes. For PNNI, use the
SET PNNI connection command to establish the routing VP.
Format
HOSTNAME# SET tunneling P1 P2 P3 P4 P5
Format Explanation
P2 : VPI (0~4095)
P3 : Tunneling bandwidth (cell/s) (1~1412830)
P4 : UPC function mode (0(off) or 1)
P5 : Shaper number (off(0) or 1~8)
NOTE Only the shaper number whose shaping rate has already been set with the
SET shaper command can be specified.
The tunneling bandwidth displays a maximum rate of 1,412,830, which is an

OC-12 rate. OC-3 or UTP-5 maximum rate is 353,207.
Output
Tunneling information has been set.

NTP 279-8013-904
SOFTPVP ? Function
(Privileged This command is used to display the help message for the SOFTPVP command.
Command)
Function Format
HOSTNAME# SOFTPVP ?
Output
HOSTNAME# softpvp ?
delete Delete soft PVPC/PVCC
establish Establish soft PVPC/PVCC
setup Setup soft PVPC/PVCC
addparty Add endpoint to existing multipoint soft PVPC/PVCC
release Release soft PVPC/PVCC
dropparty Delete endpoint from existing multipoint soft PVPC/PVCC
flush Delete all soft PVPC/PVCC on a line interface

NTP 279-8013-904
SOFTPVP Function
addparty This command is used to add endpoint to point-to-multipoint soft PVPC/PVCC.
(Privileged
Before entering this command:
Command)
Enter the same incoming side (point 1) parameters that have been set as the
incoming side parameters for the existing connection.
Use the SOFTPVP setup command to ensure that the incoming side
parameters (line number, VPI, VCI) are set to multipoint.
Format
HOSTNAME# SOFTPVP addparty P1 P2 P3 P4 {P5} {P6}
Format Explanation
P1 : Local Terminal Line Number (000~073)
P2 : Local VPI (0~4095)
P3 : Local VCI (0 (for PVPC), 32~16383)
P4 : Destination ATM address (0~9, a~f, A~F, up to 40 digits)
P5 : Remote VPI (0-4095 can be defaulted)
P6 : Remote VCI (0 (for PVPC)~ 65535 can be defaulted unless P5 is entered).
Output
Soft PVPC/PVCC endpoint has been added.

NTP 279-8013-904
SOFTPVP delete Function

(Privileged This command is used to delete the soft PVPC/PVCC.
Command)
Format
HOSTNAME# SOFTPVP delete P1 P2 P3
Format Explanation
P2 : VPI (0~4095)
P3 : VCI (0, 32~16383)
Example
HOSTNAME# SOFTPVP del 03 3 34
Output
Soft PVPC/PVCC has been deleted.

NTP 279-8013-904
SOFTPVP Function
dropparty This command is used to delete endpoint to point-to-multipoint soft PVPC/PVCC.
(Privileged
Command) Format
HOSTNAME# SOFTPVP dropparty P1 P2 P3 P4
Format Explanation
P1 : Local Line Number. (00~33)
P2 : Local VPI (0~4095)
Output
Soft PVPC/PVCC endpoint has been deleted.

NTP 279-8013-904
SOFTPVP Function
establish This command is used to set permanent virtual path connections (PVPCs) or
(Privileged permanent virtual circuit connections (PVCCs) spread over a number of switches.
Command) Unless the PVPCs/PVCCs are deleted using the SOFTPVP delete command
described elsewhere in this chapter, the switch will try to reset the PVPCs/PVCCs
up to the number of times specified by this command.
The data set with this command is stored (using the SAVE command) and retained
after the power is turned off. When power is turned back on, the connection is
automatically established.
Up to 128 soft PVPCs/PVCCs can be registered with this command.
Reference Command
DISPLAY softpvp
Cancel Command
SOFTPVP delete
Setting Procedure
1. Execute the SET local command to assign an ATM address to each border
switch on the network.
2. Set dynamic routing table by executing the SET pnni connection
command. In case of static routing, use the ROUTE add command to set the
SVC static routing table.
3. Execute the SET atmsig command to set the relationship with the other port
as "user network."
4. Execute this command to the other border switch.
Format
HOSTNAME# SOFTPVP establish P1 P2 P3 P4 P5 P6 P7 P8
P9 P10 P11 P12 P13 P14 P15 P16

NTP 279-8013-904
Format Explanation
P1 : Traffic type (1(cbr), 2(nrt-vbr), 3(rt-vbr) or 4(ubr) default is UBR)
P2 : Local terminal line number (00~33)
P3 : Local VPI (0~4095)
P5 : Called party ATM Address (0~9, a~f, A~F, up to 26 digits)
P6 : Remote device (0(M5), 1(M7), 2(M5E))
The following parameters can be set in the setting range indicated if the remote
device is an ATM 2.5 Gbps switch:
P7 : Remote Line Number
P8 : Remote VPI (0~4095)
P9 : Remote VCI (0(for PVPC), 32~16383)
P10 : Local UPC mode (off(0) or 1~5)
P11 : Local shaper number (off(0) or 1~8)
P12 : Forward profile name
P13 : Remote UPC mode (off(0) or 1~5)
P14 : Remote shaper number (off(0) or 1~8)
P15 : Backward profile name
P16 : Retry count (0~15, infinity) (default=2)
Output
Soft PVPC/PVCC has been set.
NOTE If the ATM address has not been set with the SET local command, this
command will display an error message and the Soft PVP setting will not be
performed.

NTP 279-8013-904
SOFTPVP flush Function

(Privileged This command performs the same function as DELETE, except that all SOFTPVPs
Command) are removed on the specified port.
Format
SOFTPVP flush P1
Format Explanation
P1: <slot port>
Example
HOSTNAME# SOFTPVP flush 23

SOFTPVP has been flushed.
HOSTNAME#

NTP 279-8013-904
SOFTPVP release Function

(Privileged This command is used to delete point-to-point soft PVPC/PVCC or all endpoints
Command) of point-to-multipoint soft PVPC/PVCC.
Format
HOSTNAME# SOFTPVP release P1 P2 P3
Format Explanation
P1 : Line Number (00~33)
P2 : VPI (0~4095)
P3 : VCI (0, 32~16383)
Output
Soft PVPC/PVCC has been released.

NTP 279-8013-904
SOFTPVP setup Function

(Privileged This command is used to set point-to-point or point-to-multipoint soft PVPC/
Command) PVCC by PNNI.
Setting Procedure
1. Execute the SET local command to assign an ATM address to each border
switch on the network.
2. Set the path for dynamic routing table by executing the
SET pnni connection command.
3. Set PNNI environment in the network.
4. Execute the SET atmsig command to set the relationship with the other port
as network-network.
5. Execute this command to the other border switch.
Format
HOSTNAME# SOFTPVP setup P1 P2 P3 P4 P5 P6 P7 P8 {P9}
{P10} {P11}
Format Explanation
P1 : Connection type (ptop(0), ptom(1))
P2 : Traffic type (abr(0), cbr(1), nrt-vbr(2), rt-vbr(3) or ubr(4)
abr cannot be specified if P-to-MP)
P3 : Local Line Number (00~33)
P4 : Local VPI (0~4095)
P7 : Forward profile name (can be defaulted with - for CE and Frame Relay;
however this cannot be defaulted in case of Multipoint.
P8 : Backward profile name (- if P-to-MP) (can be defaulted with - for CE and
Frame Relay in case of P-to-P)
P9 : Retry count (0~15, infinity) (default=2)
P10 :Remote VPI (0~4095 can be defaulted)
P11 :Remote VCI (0 (for PVPC)~65535 can be defaulted unless P10 is entered)
Output
Soft PVPC/PVCC has been set.

NTP 279-8013-904
TELNETPASSWD Function
(Privileged This command is used to set the password for accessing Telnet.
Command) After entering the current password, enter the new password twice to complete the
password change. The entered characters are not echoed back.
Format
HOSTNAME# TELNETPASSWD
Output
If a password is not registered:

[OK]
If a password is registered:
Input old Telnet password:

[OK]
NOTE The password must contain no less than four and no more than eight characters.
Characters are case sensitive.

NTP 279-8013-904
This page is for your notes.

NTP 279-8013-904
4
Error Messages
Command Error Message Action

***Already assigned. Based on the command entered, the port is already
defined, in use or disabled.
***Already disabled. Based on the command entered, the port is already
***Already enabled. Based on the command entered, the port is already
***Already registered. Based on the command entered, the port is already
***Already set. A mode (single/duplex) is already set.
***Another card status error. An error has occurred in the card of the other side or the
card is not installed. Check the fault or installation
condition.
***ATM routing information exceeds the ATM routing information exceeds the limit. Delete
limit. unnecessary information before repeating the entry.
***CAC overbooking factor still The CAC still exists. Delete the CAC before repeating the
existent. entry.
***Cannot drop the last leaf with SoftPVP dropparty command cannot be used to
SoftPVP dropparty. Try SoftPVP remove the last multicast endpoint. Execute the
release. SoftPVP release command.
***Cannot remove the last leaf with PVC remove command cannot be used to remove the
PVC remove. Try PVC delete. last multicast end point. Execute the PVC delete
command.
***Card I/F busy. Due to high load on the card side, the 2.5 Gbps switch and
the card cannot communicate. The load must be reduced.
***Card is not single mode. Check with Reference command before repeating the
entry.

NTP 279-8013-904
Error Messages

***Card is remote duplex mode. Check with Reference command before repeating the
entry.
***CEVC data still existent. The CEVC still exists. Delete unnecessary CEVC before
repeating the entry.
***Changing admin status. Administration status is being changed by another
process. Repeat the entry later.
***Circuit emulation data is not Check with Reference Command before repeating the
registered. entry.
***Connection already exists. The connection already exists. Repeat the entry.
***Connection(s) still existent. The connection still exists. Delete the connection before
repeating the entry. Check if the same address is already
set.
***Diagnostics fault found. Check the fault status with the DISPLAY alarm
command, then remove the cause of the fault before
***DLCI still existent. Delete the DLCI before repeating the entry.
***Duplicate assignment. Based on the command entered, the port is already
***Dynamic routing table registration Check the setting before repeating the entry.
failure.
***Flash memory status is busy. Repeat the entry later.
***FR DLCI is not registered. Set FR DLCI with the SET dlci command before
***Gateway package is not installed. Remove the cause of the fault and repeat the entry using
the correct data.
***Hardware failure found. Remove the cause of the fault and repeat the entry,
***Illegal access privilege. A value other than "0" or "1" has been entered in the
access privilege parameter. Repeat the entry using correct
data.
***Illegal access range. The access range parameter is in a format other than the
specified format or exceeds the range. Repeat the entry
using correct data.
***Illegal address type. The address type parameter is in a format other than the
specified format or exceeds the range. Repeat the entry.
***Illegal administrative weight. The administrative weight parameter is in a format other
than the specified format or exceeds the range. Repeat
the entry.
***Illegal aggregation token. The aggregation token parameter is in a format other than
the specified format or exceeds the range. Repeat the
entry.

NTP 279-8013-904
Error Messages

***Illegal ATM address. The ATM address parameter is in a format other than the
using correct data.
***Illegal available cell rate mT. The available cell rate mT parameter is in a format other
the entry.
***Illegal available cell rate PM. The available cell rate PM parameter is in a format other
the entry.
***Illegal base. The test flow base parameter is in a format other than the
specified format. Repeat the entry using correct data.
***Illegal boot mode. The specified boot mode is undefined. Repeat the entry
using correct data.
***Illegal call reference. The call reference is in a format other than the specified
format or exceeds the range. Repeat the entry.
***Illegal CAS mode. The CAS mode parameter is in a format other than the
***Illegal CDVT value. The CDVT value parameter is in a format other than the
using correct data.
***Illegal cescondition. The cescondition is in a format other than the specified
***Illegal CIR. The CIR parameter is in a format other than the specified
***Illegal clear-buffers. A parameter other than Y or N has been entered as the
clear-buffers parameter. Repeat the entry
***Illegal clock mode. The specified clock mode is undefined. Repeat the entry
using correct data.
***Illegal CLP to DE mapping mode. The CLP to DE mapping mode (frame discard priority)
parameter is in a format other than the specified format or
exceeds the range.
***Illegal CLP value. The CLP value parameter is in a format other than the
***Illegal command. The command name is undefined Repeat the entry using
correct data.
***Illegal community name. Escape sequence has been entered as the community
name. Repeat the entry using correct data.
***Illegal congestion indication The congestion indication mode (forward congestion
mode. indication) parameter is in a format other than the specified

NTP 279-8013-904
Error Messages

***Illegal connection type. The connection type parameter is in a format other than
entry.
***Illegal correlation tag. The correlation tag parameter is in a format other than the
***Illegal count. The count parameter is in a format other than the specified
***Illegal data. The data type parameter is in a format other than the
using correct data.
***Illegal data type. The data type parameter is in a format other than the
***Illegal dataname. The data name parameter is in a format other than the
***Illegal date. The date parameter is in a format other than the specified
format or exceeds the range. Repeat the entry using
correct data.
***Illegal DE to CLP mapping mode. The DE to DLP mapping mode (cell loss priority)
parameter is in a format other than the specified format or
exceeds the range. Repeat the entry.
***Illegal DE value. The specified DE value cannot be set. Repeat the entry.
***Illegal destination IP address. The destination IP address parameter is in a format other
than the specified format. Repeat the entry using correct
data.
***Illegal destination type. The destination type parameter is in a format other than
entry using correct data.
***Illegal direction. The direction parameter is in a format other than the
specified format or the specified direction cannot be set.
Repeat the entry using correct data.
***Illegal DLCI. The DLCI parameter is in a format other than the specified
***Illegal DS rxmt interval. The DS rxmt interval parameter is in a format other than
entry.
***Illegal EPD. The EPD parameter is in a format other than the specified
correct data.
***Illegal failure dump information. A value other than "all" has been entered in the failure
dump information parameter. Repeat the entry.

NTP 279-8013-904
Error Messages

***Illegal failure log number. A value other than "1" or "2" has been entered in the failure
log number parameter. Repeat then entry.
***Illegal filename. The filename parameter is in a format other than the
using correct data.
***Illegal flag. The flag parameter is in a format other than the specified
correct data.
***Illegal Forum/ITU. A value other than 0 or 1 has been entered in the Forum/
ITU parameter. Repeat the entry using correct data.
***Illegal fractional type. The fractional type parameter is in a format other than the
***Illegal Frame mode. The frame mode parameter is in a format other than the
using correct data.
***Illegal FR_Forum/ITU_T/ANSI. The standard parameter is in a format other than the
***Illegal hello interval. The hello interval parameter is in a format other than the
***Illegal hierarchy. The hierarchy parameter is in a format other than the
***Illegal hop count. The hop count range for "SETUP loop" prevention is
invalid. Repeat the entry in the range of 0 to 20.
***Illegal hostname. Escape sequence has been entered as the host name.
***Illegal idle cell. Cannot specify idle cell type. Repeat the entry using
correct data.
***Illegal IISP mode. The IISP mode parameter is in a format other than the
***Illegal index. The index parameter is in a format other than the specified
correct data.
***Illegal interface. The interface parameter is in a format other than the
using correct data.
***Illegal IP address. The IP address parameter is in a format other than the
***Illegal interworking type. The interworking type parameter is in a format other than
entry.

NTP 279-8013-904
Error Messages

***Illegal keepalive value. The keepalive parameter exceeds the range. Repeat the
***Illegal LBO. A value other than "0" or "1" has been entered in the LBO
parameter. Repeat the entry using correct data.
***Illegal length. The valid bit count exceeds the range. Repeat the entry.
***Illegal level. The level exceeds the range. Repeat the entry.
***Illegal line. The line parameter is in a format other than the specified
correct data.
***Illegal line rate. The line rate parameter is in a format other than the
***Illegal line speed. The line speed parameter is in a format other than the
using correct data.
***Illegal link down discover time. The link down discover time exceeds the range. Repeat
the entry.
***Illegal logical port number. The logical port number exceeds the range. Repeat the
entry.
***Illegal loopback condition. The loopback condition parameter is in a format other than
entry.
***Illegal looptime mode. The looptime mode parameter is in a format other than the
***Illegal mask range. The mask value exceeds the range. Repeat the entry.
***Illegal MaxCC. The MaxCC parameter exceeds the range. Repeat the
entry.
***Illegal MaxPD. The MaxPD parameter exceeds the range. Repeat the
entry.
***Illegal MaxSTAT. The MaxSTAT parameter exceeds the range. Repeat the
entry.
***Illegal MBS. The MBS parameter is in a format other than the specified
***Illegal memory type. The memory type parameter is in a format other than the
***Illegal method. The routing method parameter is in a format other than the
***Illegal minimum hello interval. The minimum hello interval parameter is in a format other
the entry.

NTP 279-8013-904
Error Messages

***Illegal minimum PTSE interval. The minimum PTSE interval parameter is in a format other
the entry.
***Illegal network interface. The network interface parameter is in a format other than
entry.
***Illegal network interface. The network interface parameter is in a format other than
***Illegal new line. The new line parameter is in a format other than the
***Illegal new scope. The new scope parameter is in a format other than the
***Illegal new VPI. The new VPI parameter is in a format other than the
***Illegal NMS number. The NMS parameter exceeds the range. Repeat the entry.
***Illegal NMS number. The NMS parameter exceeds the range. Repeat the entry
using correct data.
***Illegal node ID. The node ID parameter is in a format other than the
***Illegal noresponse. The noresponse parameter is in a format other than the
using correct data.
***Illegal number of parameters. Excess parameter has been entered or the number of
parameters is insufficient. Repeat the entry.
***Illegal number of parameters. Excess parameter has been entered or the number of
parameters is insufficient. Repeat the entry using correct
data.
***Illegal numbering ID. The numbering ID parameter is in a format other than the
***Illegal OAM mode. The OAM mode parameter is in a format other than the
***Illegal packet type. The packet type parameter is in a format other than the
***Illegal parameter. The parameter is in a format other than the specified

correct data.
***Illegal partial fill size. The partial fill size parameter is in a format other than the

NTP 279-8013-904
Error Messages

***Illegal password. The password is in a format other than the specified
format. Repeat the entry using correct data.
***Illegal PCR. The PCR parameter is in a format other than the specified
***Illegal PLCP. A value other than "0" or "1" has been entered in the PLCP
parameter. Repeat the entry using correct data.
***Illegal point. The point parameter is in a format other than the specified
correct data.
***Illegal pointer. The pointer parameter is in a format other than the
***Illegal poll. The poll parameter is in a format other than the specified
correct data.
***Illegal priority. The priority parameter is in a format other than the
***Illegal profile. The profile parameter is in a format other than the specified
correct data.
***Illegal prompt mode. The prompt mode parameter is in a format other than the
***Illegal protocol encapsulation The protocol encapsulation mode parameter is in a format
mode. other than the specified format or exceeds the range.
Repeat the entry.
***Illegal PTSE ID. The PTSE ID parameter is in a format other than the
specified. format or exceeds the range. Repeat the entry.
***Illegal PTSE interval. The PTSE interval parameter is in a format other than the
***Illegal PTSE type. The PTSE type parameter is in a format other than the
***Illegal reachable address. The reachable address parameter is in a format other than
entry.
***Illegal remote node. The remote node parameter is in a format other than the
using correct data.
***Illegal retry number. The retry number parameter is in a format other than the
using correct data.

NTP 279-8013-904
Error Messages

***Illegal router IP address. The router IP address parameter is in a format other than
***Illegal scope. The scope parameter is in a format other than the specified
***Illegal SCR. The SCR parameter is in a format other than the specified
correct data.
***Illegal scramble. A value other than "0" or "1" has been entered in the
scramble parameter. Repeat the entry using correct data.
***Illegal scroll number. The specified scroll line count is out of range. Repeat the
***Illegal service. The service parameter is in a format other than the
***Illegal shaper number. The shaper number parameter is in a format other than the
using correct data.
***Illegal side. The side parameter is in a format other than the specified
correct data.
***Illegal slot. The slot parameter is in a format other than the specified
correct data.
***Illegal status. The specified "status" is undefined. Repeat the entry using
correct data.
***Illegal sub-command. The specified subcommand name is undefined. Repeat
the entry using correct data.
***Illegal sub-netmask. The sub-netmask value is in a format other than the
***Illegal sysContact. The sysContact parameter is in a format other than the
using correct data.
***Illegal sysLocation. The sysLocation parameter is in a format other than the
using correct data.
***Illegal T301 value. A value outside the range has been entered as the
parameter for T301. Repeat the entry.
parameter for T303. Repeat the entry using correct data.

NTP 279-8013-904
Error Messages

parameter for T397. Repeat the entry.
***Illegal throughput. The throughput parameter is in a format other than the
using correct data.
***Illegal time-out. The time-out parameter is in a format other than the
using correct data.
***Illegal time. The time parameter is in a format other than the specified
correct data.
***Illegal timer. A value outside the range has been entered as the
parameter for timer. Repeat the entry using correct data.
***Illegal TimerCC. A value outside the range has been entered as the
parameter for TimerCC. Repeat the entry using correct
data.
***Illegal timeslot. The timeslot parameter is in a format other than the
***Illegal traffic type. The traffic type parameter is in a format other than the
using correct data.
***Illegal transit network ID. The transit network ID parameter is in a format other than
entry.

NTP 279-8013-904
Error Messages

***Illegal transit network ID data. An incorrect ID was entered. Repeat the entry.
***Illegal TTC/ITU. The specified standard is undefined. Repeat the entry.
***Illegal type. The type parameter is in a format other than the specified
***Illegal UNI version value. The specified UNI Version is undefined. Repeat the entry
using correct data.
***Illegal UPC mode. The UPC mode parameter is in a format other than the
***Illegal valid length for reachable The valid length for reachable address parameter is in a
address. format other than the specified format or exceeds the
range. Repeat the entry.
***Illegal valid VCI bits. The specified valid VCI bit count is out of range. Repeat
***Illegal valid VPI bits. The specified valid VPI bit count is out of range. Repeat
***Illegal VCI. The specified VCI value is out of range or cannot be used.
***Illegal VPI. The specified VPI value is out of range or cannot be used.
***Inconsistent connection label. Invalid connect information entered. Repeat the entry
using correct data.
***Inconsistent number for timeslot. An incorrect timeslot was entered. Repeat the entry.
***Insufficient PCR of profile. PCR value of profile is less than that set by the SET cevc
command. Check the profile with DISPLAY profile
command before repeating the entry.
***Interface configuration failed. Specified interface could not be configured. Repeat the
entry after remedying the error.
***Interface is not NNI. Check the setting before repeating the entry.
***Interworking type is inconsistent Check the Reference command before repeating the
with PR-profile. entry.
***Invalid CDVT value. The CDVT value is out of range. Repeat the entry using
correct data.
***Invalid connection type. Cannot set the specified connection type. Repeat the
entry.
***Invalid directional(uni/bi) Cannot set the specified directional (uni/bi) connection.
connection. Repeat the entry.
***Invalid directional(uni/bi) Cannot set the specified directional (uni/bi) connection.
connection. Repeat the entry using correct data.

NTP 279-8013-904
Error Messages

***Invalid endpoint for VP level. The specified VP level OAM point is invalid. Repeat the
***Invalid IP routing information. The specified IP routing information is invalid. Repeat the
***Invalid line. The specified line cannot be used. Check the line card
installation status and error status.
***Invalid package. Mounted package cannot be used. Check the package.
***Invalid remote node ID. The specified remote node ID is invalid. Repeat the entry
using correct data.
***Invalid shaper number. The specified shaper number is invalid. Repeat the entry
using correct data.
***Invalid slot. The specified slot is invalid or no package is installed.
***Invalid standby. The specified switch/CPU cannot be set to SBY or switch/
CPU is in single mode. Repeat the entry.
***Invalid traffic for the specified Cannot set the specified traffic for the specified direction.
direction. Check the traffic type before repeating the entry.
***Invalid UPC for the specified Cannot set the specified UPC for the specified traffic.
traffic. Check the UPC before repeating the entry.
***Invalid value. The specified value is invalid. Repeat the entry.
***Invalid VPI. The specified VPI is invalid. Repeat the entry using correct
data.
***IP address is inconsistent with Specified IP address is different from other interfaces.
another interface. Check with Reference Command before repeating the
entry.
***IP routing information exceeds the IP routing information exceeds the limit. Delete
limit. unnecessary information before repeating the entry.
***Leaf already set to another port. Leaf is already set to another port (with CE-DS1, only one
leaf may be set in a package). Repeat the entry.
***Leaf/Leaves still existent. An endpoint exists at the specified address. Delete the end
point with the PVC remove command before repeating
the entry.
***Line is not installed. Check the line card installation status.
***Line not suspended. The specified line is not in "suspend" status. Suspend the
line with the SET svcline command before repeating
the entry.
***Line out of service. The specified line has failed. Check the installation status
and error status.

NTP 279-8013-904
Error Messages

***Line rate is less than shaping rate Shaping at the specified rate cannot be done. Specify
or tunneling throughput. different shaping rate.
***Line status failure found. Remove the cause of the fault before repeating the entry.
***Line status is admindown. Specified line is inactive. Entry cannot be accepted.
Activate the line before repeating the entry.
***Line undergoing loopback test. The specified line is undergoing loopback test. Repeat the
entry after the test.
***Loading failed. Software or office data loading failed. Check the device
mounting and connection statuses before repeating the
entry.
***Local IP address and server IP Local IP address and server IP address have not been
address are not saved yet. saved (are not yet valid). Use the SAVE command to
validate the data.
***Looptime already set to another Looptime is already set on another line of the same
port. linecard (DS3/E3 only). Repeat the entry.
***Loss of 64K clock. A 64 k clock interruption (DCS only) occurred. Eliminate
the cause before repeating the entry.
***Loss of 8K clock. An 8 k clock interruption (DCS only) occurred. Eliminate
the cause before repeating the entry.
***NMS information already exists. Based on the command entered, the port is already
***No data registered. CPU under load. Wait awhile before repeating the entry.
***No memory block available. CPU under load. Wait awhile before repeating the entry.
***No route to server. Server route is not set. Check the routing information
before repeating the entry.
***No such connection. Check the currently set connection.
***No such entry. Check the currently set connection.
***No such FR-profile. Check the currently set FR profile.
***No such ILMI connection. Check with Reference command before repeating the
entry.
***No such information. Check with Reference command before repeating the
entry.
***No such shaper registered. Register shaper.
***Node ID is not registered. Register node ID before repeating the entry.
***Non-volatile memory is in use The command has been entered from another terminal.
[Failed]. Repeat the entry later.
***Non-volatile memory is in use. The command has been entered from another terminal.
Wait awhile before repeating the entry.

NTP 279-8013-904
Error Messages

***Can not create task. Cannot create task to display failure information. Wait a
while before repeating the entry.
***Can not start task. Cannot start task to display failure information. Wait a
while before repeating the entry.
***Number of access times exceeds the Replace the switch/CPU.
limit (100,000).
***Number of available connections for Delete unnecessary connection for UPC before repeating
UPC exceeds the limit. the entry.
***Number of available connections for Delete unnecessary connection for UPC before repeating
UPC exceeds the limit. the entry.
***Number of Connections exceeds the Delete unnecessary connection before repeating the
limit. entry.
***Number of ILMI connections exceeds Delete unnecessary ILMI connection before repeating the
the limit. entry.
***Number of PNNI connections exceeds Delete unnecessary PNNI connection before repeating the
the limit. entry.
***Number of reachable address exceeds Delete unnecessary address before repeating the entry.
the limit.
***Number of Signaling connections Delete unnecessary signaling connection before repeating
exceeds the limit. the entry.
***Number of Soft PVPC/PVCCs exceeds Delete unnecessary soft PVPC/PVCC before repeating
the limit. the entry.
***Number of timeslots exceeds the Delete unnecessary timeslot before repeating the entry.
limit.
***Number of VCs exceeds the limit. Delete unnecessary VC before repeating the entry.
***OAM cell monitor is busy. Repeat the entry later.
***OAM information exceeds the limit. OAM information exceeds the limit. Delete unnecessary
information before repeating the entry.
***OAMCON/OAMEND delete failure. Deletion of OAM connecting point or endpoint failed.
Check for any OAM cell being transmitted.
***Out of effective bits range. Specified bit count exceeds the effective range. Check the
effective range with the Help Command and Repeat the
***Package initializing now. Wait awhile before repeating the entry.
***PC-card access failed. Access to PCMCIA card failed. Check the card installation
condition before repeating the entry.
***PC-card access is busy. PCMCIA card is being accessed. Repeat the entry later.

NTP 279-8013-904
Error Messages

***PC-card is not installed. PCMCIA card is not installed. Install the card before
***PC-card status failure. PCMCIA card has failed. Replace the card before
***PC-card type mismatch. PCMCIA card is not an ATA card. Check the installed card.
***PNNI connection still existent. PNNI connection still exists. Delete PNNI connection
before repeating the entry.
***PNNI node information is not Execute set PNNI nodal command.
registered.
***Profile information exceeds the Delete unnecessary profile information before repeating
limit. the entry.
***Signaling connection does not Repeat the entry using correct data.
exist.
***Specified line speed dose not Shaping cannot be performed at the specified rate. Specify
execute shaping function. a different shaping rate.
***Switch-Engine initializing now. Repeat the entry later.
***Switch-Engine is single mode. Check the mounting status.
***Synchronized failure. Clock synchronization failed in changing slave to specified
line. Check the line status before repeating the entry.
***The function is not supported by Check the buffer type.
buffer on the package.
***The function is not supported by This function is not supported by the current package.
the package. Check the mounted package.
***This card has no space. There is not enough idle space on the card. Replace the
card before repeating the entry.
***This card is write protected. The card is write protected (the card is a master card).
Check the card.
***Throughput exceeds the line rate. Change the setting.

***Time out. Tunneling information exceeds the limit. Delete
unnecessary information before repeating the entry.
***Timeslot(s) already assigned. Repeat the entry.
***Total of CIR exceeds the limit. Delete unnecessary CIR information before repeating the
entry.
***Traffic type is inconsistent with Check the profile with DISPLAY profile command
profile. before repeating the entry.
***Tunneling information exceeds the Repeat the entry using correct data.
limit.

NTP 279-8013-904
Error Messages

***Unchangeable slave line exists. Specified line is a slave line and cannot switch to another
line. Set another line as slave line before repeating the
entry.
***Undergoing diagnostics test. Repeat the entry after the diagnosis.
***Undergoing execution. Wait awhile.
***Unknown error occurred. Unknown error has occurred. Contact the system
manager.
***Valid VPI + valid VCI exceeded the The specified VPI+VCI parameter exceeds the valid bit
limit. count. Repeat the entry using correct data.
***VC(s) already assigned. Check the VC information before repeating the entry.
***VPI and/or VCI exceeded the limit The specified VPI and/or VCI parameter exceeds the limit.
of valid bit number. Repeat the entry using correct data.
***Writing failed [Tftp timeout]. Data write failed. Check the mounting status of the
package and flash card before repeating the entry.
***Wrong password. The entered password does not match the registered
password. Repeat the entry using correct data.

NTP 279-8013-904
A
Glossary
AAL
ATM Adaptation Layer. A collection of standardized protocols that adapt user
traffic to 48-octet payloads that can be placed in a cell-formatted stream.
ABR
Available Bit Rate: One of the ATM Forum-defined service layers. ABR supports
variable bit rate data traffic with flow control, a minimum guaranteed data
transmission rate, and specified performance parameters.
ACH
Active Change: When an active CPU/switch module in a redundant chassis
changes over to standby, and vice versa (when a standby module becomes active).
ACT
Applied Computer Technologies: Software that integrates voice and database
technologies. With ACT, the call and the callers database record arrive at the
telephone simultaneously.
AIS
Alarm Indication Signal: One of the OAM function types used for fault
management. An alarm sent upstream denoting a link failure.
ATM
Asynchronous Transfer Mode: A high-bandwidth, low-delay, connection-oriented,
packet-like transfer mode in which information is organized into cells, and
recurrence of these cells is not necessarily periodic (and, therefore, asynchronous).
Centillion 1200N ATM Switch Command Manual A-1

NTP 279-8013-904
B Glossary
ATM Address
Defined in the UNI Specification as three 20-byte formats, including country, area,
and end-system identifiers.
ATM Forum
A consortium that recommends and defines specifications for ATM standards and
promotes industry cooperation in implementing ATM strategies.
ATM-NIC
ATM Network Interface Card: Electronic circuitryusually a card that fits into a
PCs expansion slotthat works with the network software and computer
operating system to transmit and receive messages on the network.
ATM Switch
A generic term that usually refers to a hardware-based, self-routing, high-speed
switching system rather than a switching element.
Bandwidth
The width of a communications channel. Transmission capacity of a
communications medium, measured in either bps or Hz.
BCI
Broadcast Channel Identifier.
B-ISDN
Broadband ISDN: A high-speed network standard that allows voice, data, and
video to be delivered over the same network.
BISUP
Broadband ISDN Users Part: A protocol that defines the signaling messages to
control connections and services.
BRI
Basic Rate Interface. An ISDN service specification, intended for carrying
(compressed) video, voice, and data.
A-2 Centillion 1200N ATM Switch Command Manual

NTP 279-8013-904
Glossary C
BUS
Broadcast and Unknown Server: A server that handles data sent by an LE Client to
the broadcast MAC address ('FFFFFFFFFFFF'), all multicast traffic, and initial
unicast frames sent by a LAN Emulation Client.
CAC
Connection Admission Control: Actions taken by the network during the call set-
up phase or call re-negotiation phase to determine whether a connection request
should be accepted or rejected, or whether a re-allocation request can be
accommodated.
CAS
Channel Associated Signaling: A form of circuit state signaling in which the circuit
state is indicated by one or more bits of signaling status sent repetitively and
associated with that specific circuit.
CBR
Constant Bit Rate: An ATM service category that supports a constant or guaranteed
rate to transport services such as video or voice, as well as circuit emulation which
requires rigorous timing control and performance parameters.
CDV
Cell Delay Variation: A component of cell transfer delay, induced by buffering and
cell scheduling. Peak-to-peak CDV is a QoS delay parameter associated with CBR
and VBR services.
CDVT
Cell Delay Variation Tolerance: The acceptable tolerance of the cell delay variation
(jitter). Used in CBR traffic.
CE
Circuit Emulation.
CEPT1
Conference European des Administration des Postes et des Telecommunications 1.
The European standard for digital transmission at the rate of 2.048 Mbps. Same as
E-1.

NTP 279-8013-904
D Glossary
CEVC
Circuit Emulation Virtual Circuit: A virtual circuit used in circuit emulation.
CIR
Committed Information Rate: The information rate that the network is committed
to provide to the user, under any network conditions. (Used in frame relay.)
CLP
Cell Loss Priority: A field in the ATM cell header that corresponds to the loss
priority of a cell. Lower priority cells (CLP=1) can be discarded in a congestion
situation.
CLR
Cell Loss Ratio: A QoS parameter defined as the ratio of lost cells to the total
number of transmitted cells.
CPR
Common Peer Group: The lowest level peer group in which a set of nodes is
represented. A node is represented in a peer group either directly or through one of
its ancestors.
CPU
Central Processing Unit: The brain of the computer that manipulates data and
processes instructions.
Crankback
A mechanism for partially releasing a connection setup that has encountered a
failure. This mechanism allows PNNI to perform alternate routing.
CTD
Cell Transfer Delay: The elapsed time between a cell exit event and the
corresponding cell entry event for a particular connection. The cell transfer delay
between two measurement points is the sum of the total inter-ATM node
transmission delay and the total ATM node-processing delay.
DA
Destination Address: Information sent in a forward direction indicating the address
of the called station or customer.

NTP 279-8013-904
Glossary E
DLCI
Data Link Connection Identifier: The address field in a frame relay header. The
name given to the numeric identifier of a specific virtual circuit in a frame relay.
DRAM
Dynamic Random Access Memory. The readable/writable memory used to store
data.
DS
Distributed Single Layer Test Method: An abstract test method in which the upper
tester is located in the system under test, and the point of control and observation
(PCO) is located at the upper service boundary of the Implementation Under Test
(IUT) - for testing one protocol layer. Test events are specified in terms of the
abstract service primitives (ASP) at the upper tester above the IUT, and ASPs and/
or protocol data units (PDU) at the lower tester PCO.
DS-1
Digital Signal Level 1: North American digital hierarchy signaling standard for
transmitting at 1.544 Mbps.
DS-3
Digital Signal Level 3: North American digital hierarchy signaling standard for
transmitting at 44.736 Mbps.
DTL
Data Transit List: A list of nodes and optional link IDs that completely specify a
path across a single PNNI peer group.
E.164
A public network addressing standard that uses a maximum of 16 digits. ATM uses
E.164 addressing for public network addressing.
E-1
Rate used by European CEPT carriers. Also known as CEPT1.
E-3
Rate used by European CEPT carriers to transmit 16 CEPT1s.

NTP 279-8013-904
F Glossary
Egress
The exit point. Typically refers to information being sent out of, rather than into, a
network communications port.
ELAN
Emulated Local Area Network: A logical network initiated by using the
mechanisms defined by LAN Emulation. This could include ATM and legacy
attached end stations.
EPD
Early Packet Discard: A procedure for discarding cells related to one user frame to
minimize the impact of congestion. Also known as Partial Packet Discard (PPD) or
Frame Discard (the official ATM term).
FIFO
First-in First-out: The way that most queues handle calls: the first call to come in
is handled first.
GCRA
Generic Cell Rate Algorithm: A specification for defining cell rate conformance in
terms of certain traffic parameters for VBR virtual circuits. Its implementation is
commonly known as the Leaky Bucket algorithm.
Hello Packet
A type of PNNI Routing packet that is exchanged between neighboring logical
nodes.
Hop-by-Hop Route
A route that is created when each switch along the path uses its own routing
knowledge to determine the next hop of the route, with the expectation that all
switches will choose consistent hops and the call will reach the desired destination.

NTP 279-8013-904
Glossary I
IETF
Internet Engineering Task Force: A group that developed specifications for the
interoperable implementation of IP.
IISP
Interim Interswitch Signaling Protocol: A protocol that uses UNI-based signaling
(i.e., UNI 3.0/3.1) and pre-fixed routing for switch-to-switch communication. A
precursor to, but incompatible with, PNNI.
ILMI
Interim Link Management Interface: An ATM Forum-defined interim specification
for network management functions between an end user and a network, or between
a public network and a private network
Ingress
A means of entering. Typically refers to information being sent in to, rather than
out of, a network communications port.
IP
Internet Protocol: A connectionless protocol that operates at the network layer
(layer 3) of the OSI model. This protocol works in conjunction with TCP and is
usually identified as TCP/IP.
IPOA
(Classical) IP Over ATM: IETF-defined protocols for developing IP-over-ATM
networks (i.e., IP support for the QoS classes, ARP over SVC and PVC networks),
so that common applications can be supported in an ATM environment. The main
issues in the transport of IP over ATM are packet encapsulation and address
resolution.
ITU Q.2931
The signaling standard for ATM to support Switched Virtual Connections. This is
based on the signaling standard for ISDN.

NTP 279-8013-904
L Glossary
LAN
Local Area Network: A short-distance, data communications network (typically
within a building or campus) used to link computers and peripheral devices (such
as printers).
LANE
LAN Emulation: Services, functional groups, and protocols that provide for the
emulation of LANS (using ATM as a backbone) to allow connectivity among LAN-
and ATM-attached end stations.
LE
LAN Emulation. Refer to LANE.
Leaf
Endpoint of possibly several destination links of a Point-to-Multipoint connection.
(The originating endpoint is the root.)
LE_ARP
LAN Emulation Address Resolution Protocol: A message issued by an LE client to
solicit the ATM address of another function.
LEC
LAN Emulation Client: The entity in end systems that performs data forwarding,
address resolution, and other control functions.
Local Exchange Carrier: A telephone company affiliate of a regional Bell operating
company or an independent telephone company.
LECS
LAN Emulation Configuration Server: This implements the policy-controlled
assignment of individual LE clients to different emulated LANs by providing the
LES ATM addresses.
LES
LAN Emulation Server: This implements the control coordination function for the
Emulated LAN. Examples are enabling a LEC to join an ELAN, and resolving
MAC to ATM addresses.

NTP 279-8013-904
Glossary L
LGN
Logical Group Node: A single node that represents the lowest level peer groups in
the higher level peer group.
Line Card
A plug-in electronic Printed Circuit (PC) card that operates some aspect of a
network communications device, such as a multi-port physical interface card for
terminating communication cables.
LLC
Logic Link Control: The upper sub-layer of the IEEE Layer 2 (OSI) protocol that
complements the MAC protocol. IEEE standard 802.2 includes end-system
addressing and error checking. LLC provides a common access control standard
and governs the assembly of data packets and their exchange between data stations.
LOC
Loss of Cell Delineation: A condition at the receiver, or a maintenance signal
transmitted in the PHY overhead, which indicates that the receiving equipment has
lost cell delineation. Used to monitor the performance of the PHY layer.
LOF
Loss of Frame: A condition at the receiver, or a maintenance signal transmitted in
the PHY overhead, which indicates that the receiving equipment has lost frame
delineation. This is used to monitor the performance of the PHY layer.
Logical Group Node

A logical node that represents a lower-level peer group as a single point for
purposes of operating at one level of the PNNI routing hierarchy.
Logical Node
An abstract representation of a peer group or a switching system as a single point.
Logical Node ID
A string of bits that unambiguously identifies a logical node within a routing
domain.
LOP
Loss of Pointer: A condition at the receiver, or a maintenance signal transmitted in
the PHY overhead, indicating that the receiving equipment has lost the pointer to
the start of cell in the payload. This is used to monitor the performance of the PHY
layer.

NTP 279-8013-904
M Glossary
LOS
Loss of Signal: A condition at the receiver, or a maintenance signal transmitted in
the PHY overhead, which indicates that the receiving equipment has lost the
received signal. This is used to monitor the performance of the PHY layer.
LPF
Low Pass Filter: A technique for smoothing or averaging changes to the system
clock in a MPEG-2 clock recovery circuit.
LSAP
Link Service Access Point: Logical address of boundary between layer 3 and the
LLC sub-layer 2.
MAC
Media Access Control: IEEE specifications for the lower half of the data link layer
(layer 2) that defines topology-dependent access control protocols for IEEE LAN
specifications.
MAC Address
The address for a device as it is identified at the Media Access Control layer in the
network architecture.
MAT
Maintenance and Administration Terminal: The command line interface for direct
configuration of the communications equipment.
MBS
Maximum Burst Size: In the signaling message, the Burst Tolerance (BT) is
conveyed through the MBS, which is coded as a number of cells. The BT, together
with the SCR and the GCRA, determines the MBS that may be transmitted at the
peak rate and still be in conformance with the GCRA.
MCLR
Maximum Cell Loss Ratio: The maximum ratio of the number of cells that do not
make it across the link or node compared to the total number of cells arriving at the
link or node.

NTP 279-8013-904
Glossary M
MCR
Minimum Cell Rate: An ABR service traffic descriptor, in cells per second. The
rate at which the source is always allowed to send.
MIB
Management Information Base: A directory of the logical names of all information
resources that reside in a network and pertain to the networks management. A MIB
includes the names of objects it contains and the type of information retained.
MIB Object
A collection of attributes that can be used to configure, manage, or analyze an
aspect of a network component.
MPOA
Multi-Protocol Over ATM: IETF-defined specifications and procedures that enable
Network Layer protocols to operate directly on top of ATM and provide end-to-end
internetworking between hosts in an ATM and non-ATM environment.
MPOA Client
Multi-Protocol Over ATM Client: A device that implements the client side of one
or more of the MPOA protocols. An MPOA Client is either an Edge Device
Functional Group (EDFG) or a Host Behavior Functional Group (HBFG).
MPOA Server
Multi-Protocol Over ATM Server: A device that implements the server side of one
or more of the MPOA protocols.
MPOA Service Area

Multi-Protocol Over ATM Service Area: The collection of server functions and
their clients. A collection of physical devices consisting of an MPOA server plus
the set of clients served by that server.
MPOA Target
Multi-Protocol Over ATM Target: A set of protocol address, path attributes (e.g.,
internetwork layer QoS, other information derivable from received packet)
describing the intended destination and its path attributes that MPOA devices may
use as lookup keys.
MTBF
Mean Time Between Failures: The length of time a user may reasonably expect a
device or system to work before an incapacitating fault occurs.

NTP 279-8013-904
N Glossary
MTP
Message Transfer Part: Level 1 through 3 protocols of the SS7 protocol stack. MTP
3 (level 3) is used to support BISUP.
Multicasting
The transmit operation of a single PDU by a source interface where the PDU
reaches a group of one or more destinations.
Multiplexing
A function within a layer that interleaves information from multiple connections
into one connection.
Multipoint Access
User access in which more than one terminal equipment (TE) is supported by a
single network termination.
Multipoint-to-Multipoint Connection
A collection of associated ATM VC or VP links and their associated nodes.
MUX
Multiplexer: Electronic equipment that allows two or more signals to pass over one
communications circuit, such as a phone line, a microwave circuit, or a through-
the-air TV signal. There are many multiplexing techniques to accommodate both
analog and digital circuits.
NC
Network Connection
NG
No good: A command occasionally displayed on the MAT indicating a failure of a
particular switch entity.
NIC
Network Interface Card: The attachment that connects a device to a network. The
NIC, usually a PC expansion board, executes the code needed by the connected
device to share a cable or some other media with other stations.

NTP 279-8013-904
Glossary O
N-ISDN
Narrowband Integrated Services Digital Network: Services include basic rate
interface (2B+D or BRI) and primary rate interface (23B+D or PRI). Supports
narrowband speeds at/or below 1.5 Mbps.
NMS
Network Management System: An entity that implements functions at the Network
Management Layer. It may also include Element Management Layer functions. A
Network Management System may manage one or more other Network
Management Systems.
NMS Environment
A set of NMSs that cooperate to manage one or more subnetworks.
NNI
Network Node Interface: The standard interface between two network nodes
(typically ATM switches) within the same network.
Node
Synonymous with logical node.
NSAP
Network Service Access Point: OSI generic standard for a network address
consisting of 20 octets. ATM has specified E.164 for public network addressing and
the NSAP address structure for private network addresses.
OAM
Operations, Administration, and Maintenance: A group of network management
functions that provide network fault indication, performance information, and data
and diagnosis functions.
OC
Optical Carrier. Fiber-based network communication medium.
Octet
A term for eight (8) bits that is sometimes used interchangeably with byte.

NTP 279-8013-904
P Glossary
OOF
Out of Frame. Refer to LOF.
OSI
Open Systems Interconnection: The OSI Reference Model (OSIRM) introduced by
the ISO consists of seven (7) layers, each specifying the protocols and functions
required for two nodes to communicate using the underlying network infrastructure
and enable user-defined applications to access the network. The seven layers are
Physical, Data Link, Network, Transport, Session, Presentation, and Application.
Packet
Term for the OSIRM Layer 3 data transfer unit defined for packet switching
networks. A packet is of variable or fixed size, and is passed from one network node
to another. Successive packets can belong to the same message, but they have
individual headers and trailers and may be routed independently through the
network.
Packet Switch
A device that routes and forwards structured messages (packets).
Packet Switching
A data transmission method used in a network where user information is segmented
and routed in discreet data envelopes called packets, each with its own appended
control information for routing, sequencing, and error checking. Packet switched
networks typically employ a full three-layer protocol stack (physical link, data link,
network) in every node.
PCMCIA
Personal Computer Memory Card International Association: Standardizes credit-
card size packages for memory and input/output (modems, LAN cards etc.) for
computers, laptops, palmtops, etc. There are three physical standard for PCMCIA
cards-Type 1,2,3 and undefined standard called type 4, which only Toshiba has at
this moment.

NTP 279-8013-904
Glossary P
PCR
Peak Cell Rate: The cell rate (in cells per second) which the source may never
exceed.
Program Clock Reference: A timestamp that is inserted by the MPEG-2 encoder
into the Transport Stream to aid the decoder in the recovering and tracking the
encoder clock.
PDU
Protocol Data Unit. A term that describes the primitive passed across the different
layers containing control and data information.
PG
Peer Group: A set of logical nodes which are grouped for purposes of creating a
routing hierarchy. PTSEs are exchanged among all members of the group.
PGL
Peer Group Leader: A single real physical system which has been elected to
perform some of the functions associated with a logical group node.
Physical Layer (PHY) Connection

The physical transmission medium that links devices, over fiber or copper.
PLCP
Physical Layer Convergence Protocol: The PLCP is defined by the IEEE 802.6. It
is used for DS3 transmission of ATM. ATM cells are encapsulated in a 12
5microsecond frame defined by the PLCP which is defined inside the DS3 M-
frame.
PNNI
Private Network-Network Interface: A routing information protocol that enables
extremely scalable, full function, dynamic multi-vendor ATM switches to be
integrated in the same network.
PPD
Partial Packet Discard: A procedure for discarding cells related to one user frame
to minimize the impact of congestion.
PRI
Primary Rate Interface: An ISDN specification that provides twenty-three 64-kbps
B-channels and one 64-kbps D-channel, or thirty 64-kbps B-channels and one 64-
kbps D-channel.

NTP 279-8013-904
P Glossary
Private ATM Address

A 20-byte address used to identify an ATM connection termination point.
Protocol
Rules and formats (semantic and syntactic) that determine the communication
behavior of layer entities in the performance of the layer functions.
P-to-MP
Point-to-Multipoint Connection: A single ingress VC/VP copied to multiple egress
endpoints. Traffic only flows from the root to the endpoints.
P-to-P
Point-to-Point Connection: A connection with only two endpoints.
PTSE
PNNI Topology State Element: A collection of PNNI information that is flooded
among all logical nodes within a peer group.
PTSP
PNNI Topology State Packet: A type of PNNI Routing packet that is used for
flooding PTSEs among logical nodes within a peer group.
PVC
Permanent Virtual Circuit: This is a link with static route defined in advance,
usually by manual setup.
PVCC
Permanent Virtual Circuit Connection: A Virtual Circuit Connection (VCC) is an
ATM connection where switching is performed on the VPI/VCI fields of each cell.
A Permanent VCC is one which is provisioned through some network management
function and left up indefinitely.
PVP
Permanent Virtual Path: A grouped set of PVCs that exist between two crosspoints
(e.g., switches). See also Soft PVP.
PVPC
Permanent Virtual Path Connection: An ATM connection where switching is
performed on the VPI field only of each cell. A Permanent VPC is one which is
provisioned through some network management function and left up indefinitely.

NTP 279-8013-904
Glossary Q
Q.2931
ITU-T recommendation to provide SVC specifications and standards. Used in
signaling to set up and tear down virtual connections.
QoS
Quality of Service: Performance of transmission over a given virtual connection
(VC), as measured by several QoS parameters (Cell Loss Ratio, Cell Transfer
Delay, Cell Delay Variation, etc.).
RCC
Routing Control Channel: An SVC established between two PNNI leaders of a
multi-level hierarchy, enabling the exchange of PTSEs.
RDI
Remote Defect Indication: A link failure fault management indication
(downstream).
Route Server
A physical device that runs one or more network layer routing protocols, and uses
a route query protocol to provide forwarding descriptions to clients.
Router
A physical device that is capable of forwarding packets based on network layer
information, using one or more network layer routing protocols.
Routing
A network management function responsible for forwarding packets from their
source to their destination, using look-up routing tables and routing protocols (such
as EGP, OSPF, and RIP).
RS-232C
A set of standards specifying various electrical and mechanical characteristics for
interfaces between computers, terminals, and modems. The standard applies to
both synchronous and asynchronous binary data transmission.

NTP 279-8013-904
S Glossary
SAP
Service Access Point: Software interface between the layers in the OSI model
through which layers can communicate with each other by passing over PDUs.
SAPs are identified as OSI addresses.
SCCP
Signaling Connection and Control Part: A SS7 protocol that provides additional
functions to the Message Transfer Part (MTP). It typically supports Transaction
Capabilities Application Part (TCAP).
SCP
Service Control Point: A computer and database system that executes service logic
programs to provide customer services through a switching system. Messages are
exchanged with the SSP through the SS7 network.
SCR
Sustainable Cell Rate: An ATM traffic parameter (in cells per second) that
characterizes a bursty source and specifies the average rate at which cells can be
sent over a virtual connection.
SDT
Structured Data Transfer: An AAL1 data transfer mode in which data is structured
into blocks, which are then segmented into cells for transfer.
SNMP
Simple Network Management Protocol: The IETF standard management protocol
for TCP/IP networks.
Soft PVC
Soft Permanent Virtual Connection: A PVC-type connection where SVCs services
are used for virtual circuit establishment and automatic re-routing within the
network.
SONET
Synchronous Optical Network: An ANSI standard for transmitting information
over optical fiber. This standard is used or accepted in the United States and Canada
and is a variation of the SDH International standard.

NTP 279-8013-904
Glossary S
Source Route
As used in this document, a hierarchically complete source route. The course of
connecting a pending network call request is determined by the initial switch.
Source Traffic
A set of traffic parameters belonging to the ATM Traffic Descriptor used during the
connection set-up to capture the intrinsic traffic characteristics of the connection
requested by the source.
SPE
SONET Synchronous Payload Envelope. The SONET frame format is divided into
two main areas: Synchronous Payload Envelope (SPE) and Transport Overhead
(TOH). The SPE contains the information being transported by the frame.
SR
Source Routing: A bridged method whereby the source at a data exchange
determines the route that subsequent frames will use.
SRT
Source Routing Transparent: An IETF Bridging Standard combining Transparent
Bridging and Source Route Bridging.
SSCOP
Service Specific Connection Oriented Protocol: An adaptation layer protocol
defined in ITU-T Specification: Q.2110.
STM
Synchronous Transfer Module: A basic building block used for a synchronous
multiplexing hierarchy defined by the CCITT/ITU-T.
STM-1
Synchronous Transport Module 1: SDH standard for transmission over OC-3
optical fiber at 155.52 Mbps.
STM-n
Synchronous Transport Module-n: SDH standard for transmission over optical
fiber at n times the basic STM-1 rate.

NTP 279-8013-904
S Glossary
STS-1
Synchronous Transport Signal 1: SONET standard for transmission over OC-1
optical fiber at 51.84 Mbps.
STS-n
Synchronous Transport Signal-n: SONET signaling standard for transmission over
optical fiber at n times the basic STS-1 signal.
STS-nc
Synchronous Transport Signal n concatenated: SONET standards for
transmission over OC-n optical fiber by multiplexing n STS-1 frames.
Sublayer
A logical sub-division of a layer.
Subnetwork (subnet)
In general, a collection of managed entities grouped together from a connectivity
perspective, according to their ability to transport ATM cells. For MPOA, more
specific terms are Internetwork Address Sub-Group, Direct Set, Host Apparent
Address Sub-Group, and One Hop Set.
subNMS
Subnetwork Management System: A Network Management System that is
managing one or more subnetworks and that is managed by one or more Network
Management Systems.
Summary Address
An address prefix that tells a node how to summarize reachability information.
SVC
Switched Virtual Circuit: A connection established via signaling. The user defines
the endpoints when the call is initiated.
SVCC
Switched Virtual Circuit Connection: A Switched VCC is one which is established
and taken down dynamically through control signaling.

NTP 279-8013-904
Glossary T
SVPC
Switched Virtual Path Connection: A Switched Virtual Path Connection is one
which is established and taken down dynamically through control signaling. A
Virtual Path Connection (VPC) is an ATM connection where switching is
performed on the VPI field only of each cell.
Switched Connection
A connection established via signaling.
Switching System
One or more systems that act together and appear as a single switch for the purposes
of PNNI routing.
TAXI
Transparent Asynchronous Transmitter/Receiver Interface: An interface that
provides connectivity over multimode fiber links at a speed of 100 Mbps.
TCAP
Transaction Capabilities Applications Part: A connectionless SS7 protocol for the
exchange of information outside the context of a call or connection. It typically runs
over SCCP and MTP 3.
TE
Terminal Equipment: One of the two ends (at the protocol level) of an ISDN
connection (typically a PBX or a computer). An endpoint.
Telnet
A virtual terminal protocol that allows for remote host access.
T1E1
An ANSI standards sub-committee dealing with network interfaces.
T1M1
An ANSI standards sub-committee dealing with inter-network Operations,
Administration and Maintenance.

NTP 279-8013-904
U Glossary
T1Q1
An ANSI standards sub-committee dealing with performance.
T1S1
An ANSI standards sub-committee dealing with services, architecture and
signaling.
T1X1
An ANSI standards sub-committee dealing with digital hierarchy and
synchronization.
TCAP
Transaction Capabilities Application Part.
TCP
Transmission Control Protocol: A standardized transport protocol developed for
interconnecting end systems over IP-based networks.
TDM
Time Division Multiplexing: A method in which a transmission facility is
multiplexed among a number of channels by allocating the facility to the channels
on the basis of time slots.
TFTP Server
Trivial File Transfer Protocol: A simplified version of FTP that transfers files but
does not provide password protection or user-directory capability. It is associated
with the TCP/IP family of protocols.
UBR
Unspecified Bit Rate: An ATM service category that does not specify traffic-related
service guarantees. Specifically, UBR does not include per-connection negotiated
bandwidth. No numerical commitments are made regarding cell loss ratio or cell
transfer delay.

NTP 279-8013-904
Glossary V
UNI
User-Network Interface: An interface point between ATM end users and a private
ATM switch, or between a private ATM switch and the public carrier ATM network.
Defined by physical and protocol specifications, UNI is the standard adopted by
the ATM Forum to define connections between users (or end stations) and a local
switch.
UPC
Usage Parameter Control: Actions taken by the network to monitor and control
traffic that could affect the QoS of established connections.
VBR
Variable Bit Rate: An ATM Forum-defined service category which supports
variable bit rate data traffic with average and peak traffic parameters.
VBR-NRT
Variable Bit RateNon-Real Time: One of the two VBR service types for
transmitting traffic where timing information is not critical. VBR-NRT is delay-
tolerant and, therefore, well-suited for bursty traffic such as data communications.
VBR-RT
Variable Bit RateReal Time: One of the two VBR service types for transmitting
traffic that depends on timing (between source and destination) and control
information. VBRRT is suitable for carrying delay-sensitive traffic such as
packetized (compressed) video and audio.
VC
Virtual Channel: One of several logical connections defined within one virtual path.
Virtual Circuit: A connection between a source and a destination, where a fixed
route is chosen for the entire session and bandwidth is dynamically allocated to the
user.
Virtual Connection: A connection between a source and a destination, where
packets are forwarded along the same path and bandwidth is not permanently
allocated until it is used.
VCC
Virtual Circuit Connection: A concatenation of VCLs. An ATM connection where
switching is performed on the VPI/VCI fields of each cell.

NTP 279-8013-904
W Glossary
VCCI
VCC Identifier.
VCI
Virtual Channel Identifier: A unique numerical tag as defined by a 16-bit field in
the ATM cell header that identifies a virtual channel, over which the cell is to travel.
VCL
Virtual Channel Link: A means of transporting ATM cells between the point where
a VCI value is assigned and the point where that value is translated or removed.
VP
Virtual Path: A logical connection between two ATM devices (CPEs, switches). A
virtual path consists of a set of virtual channels.
VPC
Virtual Path Connection: A concatenation of VPLs. Switching cells within an ATM
switch for a given VPC is based on the VPI value indicated on the cell header.
VPI
Virtual Path Identifier: A value in the cell header that identifies the virtual path to
which the cell belongs. The field is eight (8) bits in cells traversing the UNI circuit
and 12 bits in cells traversing network circuits.
VPL
Virtual Path Link: A means of unidirectional transport of ATM cells between the
point where a VPI value is assigned and the point where that value is translated or
removed.
WAN
Wide Area Network: A network that spans a large geographic area and typically
includes public telephone circuits.
XATOM
Expandable ATM Output Modular Switch.

NTP 279-8013-904

Centillion 1200N Atm Switch Command Manual: Broadband STP

Uploaded by

Copyright:

Available Formats

Centillion 1200N Atm Switch Command Manual: Broadband STP

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Centillion 1200N Atm Switch Command Manual: Broadband STP

Uploaded by

Copyright:

Available Formats

297-8013-904

Information subject to change without notice

Network Equiipment Building Systems (NEBS)

FCC Part 15 Requirements

FCC Part 68 Registration

Location of FCC Compliance Labels

Regulatory Information for Analog Telephone

IC CS03 Certification (Canada)

Centillion 1200N ATM Switch Command Manual i

DELETE shaper (Privileged Command) . . . . . . . . . . . . . . . . . 3-28

ii Centillion 1200N ATM Switch Command Manual

DISPLAY shaper (General Command) . . . . . . . . . . . . . . . . . 3-113

Centillion 1200N ATM Switch Command Manual iii

SET cevc (Privileged Command) . . . . . . . . . . . . . . . . . . . . . 3-191

iv Centillion 1200N ATM Switch Command Manual

Centillion 1200N ATM Switch Command Manual 1-1

1-2 Centillion 1200N ATM Switch Command Manual

Example General Command Mode

Privileged Command Mode

Centillion 1200N ATM Switch Command Manual 1-3

ATM Switch commands are described in "Commands" on Page 3-1.

1-4 Centillion 1200N ATM Switch Command Manual

Command Sub-Command Function Page

Centillion 1200N ATM Switch Command Manual 2-1

Command Sub-Command Function Page

2-2 Centillion 1200N ATM Switch Command Manual

Command Sub-Command Function Page

Centillion 1200N ATM Switch Command Manual 2-3

Command Sub-Command Function Page

2-4 Centillion 1200N ATM Switch Command Manual

Command Sub-Command Function Page

Centillion 1200N ATM Switch Command Manual 2-5

Command Sub-Command Function Page

2-6 Centillion 1200N ATM Switch Command Manual

Command Sub-Command Function Page

Centillion 1200N ATM Switch Command Manual 2-7

This page is for your notes.

2-8 Centillion 1200N ATM Switch Command Manual

ATM Switch Commands

Output (General Mode)

DISPLAY<cmd> Display configuration data.

ENABLE Enable privileged commands

EXIT Exit from privileged mode or close

?/HELP Show available commands

OPEN Enable access to cards CPU

SHOW<cmd> Display configuration data

Centillion 1200N ATM Switch Command Manual 3-1

Output (Privileged Mode)

BACKUP<cmd> Backup configuration data

CLEAR<cmd> Clear configuration data or traffic counter (Type "clear

DEBUG<cmd> Debug protocol (Type "debug ?" for list.)

DELETE<cmd> Delete configuration data (Type "delete ?" for list.)

DIAGNOSIS<cmd> Diagnose hardware (Type "diagnosis ?" for list.)

DISPLAY<cmd> Display configuration data (Type "display ?" for list.)

ENABLE Enable privileged commands(Password required)

EXIT Exit from privileged mode or close current Telnet session

GENERATE<cmd> Generate OAM cells (Type "generate ?" for list.)

?/HELP Show available commands

INSTALL Install system files or configuration data. OPEN Enable