FTR-K1 SERIES

MINIATURE RELAY
2 POLES - 1 to 2 A (For Signal Switching)
NA Series
n FEATURES
lSlim type relay for high density mounting

lConforms to Telcordia specification and FCC Part 68

- Dielectric strength 1,500 VAC between coil and contacts
- Surge strength 2,500 V between coil and contacts
(at 2 10 s surge wave)
UL, CSA recognized
l

High sensitivity and low consumption power

l

High reliability - bifurcated contacts

l

DIL pitch terminals

l

Plastic sealed type

l

RoHS compliant.
l

Please see page 8 for more information

n PARTNUMBER INFORMATION
NA L - D 12 W - K
[Example] (a) (b) (*) (c) (d) (e) (f)

(a) Relay type NA : NA Series

(b) Coil type Nil : Standard type

L : Latching type

(c) Number of coil Nil : Single winding type
D : Double winding type

(d) Coil rated voltage 12 : 1.5....48VDC

Coil rating table at page 3

(e) Contact style W : Bifurcated type

(f) Enclosure K : Plastic sealed

Note: Actual marking omits the hyphen ( - ) of (*).

1
 FTR-K1 SERIES
NA SERIES
n SPECIFICATION
Item Single winding Double winding
Standard type
latching type latching type
NA - ( ) W - K NAL - ( ) W - K NAL-D ( ) W - K
Contact Configuration 2 form C (DPDT)
Data Construction Bifurcated
Material Gold overlay silver alloy (AgPd)
Resistance (Initial) Max. 50 m at 1 A, 6 VDC
Contact rating (resistive) 0.5A, 125VAC or 1A, 30VDC
Max. carrying current 2A
Max. switching voltage 250VAC / 220VDC
Max. switching power 62.5 AV / 30W
Max. switching current 2A
Min. switching load * 0.01 mA, 10 mVDC
Approx. 0.5 pF (open contacts, adjacent contacts)
Capacitance
Approx. 1.0 pF (between coil and contacts)
Life Min. 100 x 106
Mechanical Min. 10 x 106 operations
operations
Min. 200 x 103 operations (0.5A, 125VAC),
Electrical
Min. 500 x 103 operations (1A, 30VDC)
Coil Data Rated power 140 - 300 mW 100 - 150 mW 200 - 300 mW
Operate power 80 - 70 mW 60 - 85 mW 115 - 170 mW
Operating temperature range -40 C to +85 C (no frost)
Timing Data Operate (at nominal voltage) Max. 6 ms Max. 6 ms (set)
Release (at nominal voltage) Max. 4 ms Max. 6 ms (reset)
Insulation Resistance (Initial) Min. 1,000MOhm at 500VDC
Open contacts /
1,000VAC (50/60Hz) 1min
adjacent contacts
Dielectric strength
1,000VAC (50/60Hz)
Contacts to coil 1,500VAC (50/60Hz) 1min.
1min
Open contacts /
1,500V / 10 x 700s standard wave
adjacent contacts
Surge strength
1,500V / 10 x 160s
Coil to contacts 2,500V / 2 x 10s standard wave
standard wave
Other Misoperation 10 to 55Hz double amplitude 3.3mm
Vibration resistance
Endurance 10 to 55Hz double amplitude 5.0mm
Misoperation 500m/s (11 1ms)
Shock
Endurance 1,000m/s (6 1ms)
Weight Approximately 1.5 g

* Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual
load before production since reference values may vary according to switching frequencies, environmental conditions
and expected reliability levels.

2
 NA SERIES
FTR-K1 SERIES

n COIL RATING
Standard type

Rated Coil Must Operate Must Release-

Coil Coil Resistance Max. Coil Voltage Rated Power
Voltage Voltage Voltage
Code +/- 10% (Ohm) (VDC) (mW)
(VDC) (VDC) * (VDC) *
1.5 1.5 16.1 +1.13 +0.15 3.6
3 3 64.3 +2.25 +0.3 7.2
4.5 4.5 145 +3.38 +0.45 10.8
5 5 178 +3.75 +0.5 12.0 140
6 6 257 +4.5 +0.6 14.4
9 9 579 +6.75 +0.9 21.6
12 12 1,028 +9 +1.2 28.8
18 18 1,620 +13.5 +1.8 36.0
200
24 24 2,880 +18 +2.4 48.0
48 48 7,680 +36 +4.8 84.0 300

Single winding latching type

Rated Coil Reset
Coil Coil Resistance Set Voltage Rated Power
Voltage Voltage
Code +/- 10% (Ohm) (VDC) * (mW)
(VDC) (VDC) *
1.5 1.5 22.5 +1.13 -1.13
3 3 90 +2.25 -2.25
4.5 4.5 203 +3.38 -3.38
100
5 5 250 +3.75 -3.75
6 6 360 +4.5 -4.5
9 9 810 +6.75 -6.75
12 12 1,440 +9 -9
18 18 2,160 +13.5 -13.5
150
24 24 3,840 +18 -18

Note: All values in the table are valid for 20C and zero contact current.
* Specified operate values are valid for pulse wave voltage.

3
 NA SERIES
FTR-K1 SERIES

n COIL RATING
Double winding latching type
Rated Coil Reset
Coil Coil Resistance Set Voltage Rated Power
Voltage Voltage
Code +/- 10% (Ohm) (VDC) * (mW)
(VDC) (VDC) *
1.5 1.5 P 11.25 +1.13
S 11.25 +1.13
3 3 P 45 +2.25
S 45 +2.25
4.5 4.5 P 101 +3.38
S 101 +3.38
200
5 5 P 125 +3.75
S 125 +3.75
6 6 P 180 +4.5
S 180 +4.5
9 9 P 405 +6.75
S 405 +6.75
12 12 P 720 +9
S 720 +9
18 18 P 1,080 +13.5
S 1,080 +13.5 300
24 24 P 1,920 +18
S 1,920 +18

Note: All values in the table are measured at 20C and zero contact current. P: Primary coil S: Secondary coil
* Specified values are measured with pulse wave voltage

n SAFETY STANDARDS

Type Compliance Contact rating

UL UL 508, UL 1950 Flammability: UL 94-V0 (plastics)
0.5A, 125VAC (general use)
E 45026 2A, 30VDC (resistive)
CSA C22.2 No. 14, No. 950 0.3A, 110VDC (resistive)
LR 35579

Complies to IEC60950-1; FCC part 68: Telcordia

(Relay is only marked with UL and CSA logo)

4
 NA SERIES
FTR-K1 SERIES

n CHARACTERISTIC DATA

5
 NA SERIES
FTR-K1 SERIES

n REFERENCE DATA

6
 NA SERIES
FTR-K1 SERIES

n DIMENSIONS

l Dimensions l Schematics l PC board mounting

(BOTTOM VIEW) hole layout
(BOTTOM VIEW)
NA, NAL (Standard type, Single winding latching type)

NAL-D (Double winding latching type)

Unit: mm

7
 NA SERIES
FTR-K1 SERIES

RoHS Compliance and Lead Free Information

1. General Information
l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC
including amendments.
l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005.

(Amendment to Directive 2002/95/EC)

l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes

at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf
l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified.

This material has been verified to be compatible with PbSn assembly process.

2. Recommended Lead Free Solder Profile

l Recommended solder Sn-3.0Ag-0.5Cu.

Flow Solder condition:

Pre-heating: maximum 120C
Soldering: dip within 5 sec. at
260C solder bath

Solder by Soldering Iron:

Soldering Iron
Temperature: maximum 360C
Duration: maximum 3 sec.

We highly recommend that you confirm your actual solder conditions

3. Moisture Sensitivity
l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated.

4. Tin Whiskers
l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length
whisker was found by our in house test.

8
 NA SERIES
FTR-K1 SERIES

Fujitsu Components International Headquarter Offices

Japan Europe
Fujitsu Component Limited Fujitsu Components Europe B.V.
Gotanda-Chuo Building Diamantlaan 25
3-5, Higashigotanda 2-chome, Shinagawa-ku 2132 WV Hoofddorp
Tokyo 141, Japan Netherlands
Tel: (81-3) 5449-7010 Tel: (31-23) 5560910
Fax: (81-3) 5449-2626 Fax: (31-23) 5560950
Email: [email protected] Email: [email protected]
Web: www.fcl.fujitsu.com Web: emea.fujitsu.com/components/

North and South America Asia Pacific

Fujitsu Components America, Inc. Fujitsu Components Asia Ltd.
250 E. Caribbean Drive 102E Pasir Panjang Road
Sunnyvale, CA 94089 U.S.A. #01-01 Citilink Warehouse Complex
Tel: (1-408) 745-4900 Singapore 118529
Fax: (1-408) 745-4970 Tel: (65) 6375-8560
Email: [email protected] Fax: (65) 6273-3021
Web: http://us.fujitsu.com/components Email: [email protected]
Web: http://www.fujitsu.com/sg/services/micro/components/

2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective
owners.

The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for gen-
eral information purposes.
The use of the contents, data and information provided in this datasheet is at the users own risk.
Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehen-
sive, complete and up to date.
Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf
of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information
and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof.
Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility
or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for
particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy,
comprehensiveness, usefulness, availability and completeness thereof. Rev. March 02, 2011