November 19, 2015

Tech Brief ANSI B11 Machine Guarding Standards

Currents Standards Published and Available

The American Society of Safety Engineers is pleased to partner with the ANSI B11 Committee
to move machine guarding safety forward to better protect workers and reduce hazards and
exposures resulting from the use of this type of equipment.

B11 Standards, Inc. is an ANSI-accredited Standards Developing Organization that administers

and develops the ANSI B11 series of American National Standards and Technical Reports on
machine/machine tool/machinery safety. Founded in 2010, B11 Standards, Inc. is also accredited
by ANSI as the United States Technical Advisory Group Administrator to ISO Technical
Committee 199 (machinery safety standards) and ISO Technical Committee 39 Subcommittee 10
(machine tool safety standards).

B11 Standards Inc. also participates in a very large number of both national and international
standards development activities.

The Past

Standardization / standards provide a bridge between research, innovation and the market,
thereby strengthening competitiveness and boosting growth and jobs. Standards are a valuable
tool for market dissemination of research and development results and can therefore contribute to
the objectives of overall market innovation and competitiveness.

The original project on Safety Standard for Power Presses, B11, was initiated under the
procedures of the American Engineering Standards Committee (which later became the
American Standards Association, the United States of America Standards Institute, and in 1969
the American National Standards Institute - ANSI), with the National Safety Council as sponsor.
The first standard, bearing the title Safety Code for Power Presses and Foot and Hand Presses,
was developed by Sectional Committee B11 and was approved on November 13, 1922. Only two
purposes of that "code" were listed. The first and primary use was for state industrial
commissions in developing their workplace codes. The second use was as an operating guide for
users operating press production systems.

1
Revisions of the first B11 standard were issued in 1926, 1937, 1948, 1960, 1971, 1982, 1988,
2001 and 2009. The Association For Manufacturing Technology (AMT) assumed this activity
from the National Safety Council in 1970 and administered the activity until 2010, when they
transferred it to B11 Standards, Inc., which is now the ANSI-Accredited Standards Developing
Organization (SDO) for the B11 series of safety standards for machines and is the Secretariat for
the B11 Accredited Standards Committee (ASC).

The Present

The B11 ASC is comprised of organizations representing different stakeholder groups having a
substantial interest and competence in the overall scope of B11 standards. It is recognized by
ANSI as the body that evaluates and votes on final draft standards (or technical reports)
developed by B11 writing subcommittees for approval as American National Standards and
ANSI Technical Reports by the ANSI Board of Standards Review. Each of the standards and
technical reports within the B11 series has its own writing subcommittee. These subcommittees
function somewhat autonomously from the B11 ASC, with their own Chair (and possibly Vice-
Chair), however, they are ultimately responsible and answerable to the B11 ASC. Once they
complete work on their document, it is turned over to the Secretariat for procedural commenting
and balloting by the public and the interested Voting Group of B11 ASC Member organizations,
which forms the "consensus body." Once this process has been completed, the candidate
standard is submitted to the ANSI Board of Standards Review for approval as a new or revised
or reaffirmed American National Standard.

Listing of the ANSI B11 Machine Guarding Standards

ANSI B11.0-2015: Safety of Machinery

Scope: This Type-A standard applies to new, existing, modified or rebuilt

power driven machines, not portable by hand while working, that are used
to process materials by cutting; forming; pressure; electrical, thermal or
optical techniques; lamination; or a combination of these processes. This
includes associated equipment used to transfer material or tooling,
including fixtures, to assemble/disassemble, to inspect or test, or to
package. The associated equipment, including logic controller(s) and associated software or
logic together with the machine actuators and sensors, are considered a part of the industrial
machinery.

This can be a single machine or a machinery system(s).

Informative Note 1: To improve readability, the terms machine, machinery, machine

tool or machinery system(s) are used interchangeably throughout the document, either in
singular or plural form.

2
Informative Note 2: A machine system is a systematic array of one or more industrial machines
that is not portable by hand while working and includes any associated material handling,
manipulating, gauging, measuring, or inspecting equipment.

Informative Note 3: See ANSI B11.20 for additional information on integrated manufacturing
systems.

This standard specifies basic terminology, principles and a methodology for achieving safety in
the design and the use of machinery. It specifies principles of risk assessment and risk reduction
to help designers, integrators and users of machinery in achieving this objective. These
principles are based on knowledge and experience of the design, use, incidents, accidents and
risks associated with machinery. Procedures are described for identifying hazards and estimating
and evaluating risks during relevant phases of the machine life cycle, and for the elimination of
hazards or the provision of sufficient risk reduction. Guidance is given regarding the
documentation and verification of the risk assessment and risk reduction process.

Other industry sectors may benefit from applying this standard. A risk assessment may be
required to determine if a machine specific (Type-C) standard covers the hazards associated with
the application of the machine covered by the Type-C standard.

Where a machine-specific (Type-C) standard exists, the requirements of the machine-specific

(Type-C) standard shall generally apply. Deviations from the requirements of this standard or
from any machine-specific (Type-C) standard shall be based on a documented risk assessment.
Informative Note 1: See clause 6 for additional information on risk assessment.
Informative Note 2: See 7.16 for a list of example machines covered by other specific
standards.

ANSI B11.1-2009 (R2014): Safety Requirements for Mechanical Power Presses

Scope: The requirements of this standard apply only to those

mechanically-powered machine tools commonly referred to as
mechanical power presses, which transmit force mechanically to cut,
form, or assemble metal or other materials by means of tools or dies
attached to or operated by slides.

Excluded from the requirements of this standard are: bulldozers; cold-

headers and cold formers; eyelet machines; forging presses and
hammers; high-energy-rate presses; hot-bending and hot-metal presses; hydraulic power presses;
iron workers and detail punches; metal shears; pneumatic power presses; powdered-metal
presses; press welders; power pressure brakes; riveting machines; turret and plate-punch
machines; wire terminating machines; and welding presses.

3
 ANSI B11.2-2013: Safety Requirements for Hydraulic and
Pneumatic Power Presses

Scope: The requirements of this standard apply only to those

machine tools, commonly referred to as hydraulic power presses,
which transmit force hydraulically to cut, form, or assemble metal or
other materials by means of tools or dies attached to or operated by
slides.

Excluded from the requirements of this standard are: Manually powered presses; mechanical
power presses; air powered presses; powdered metal presses; horizontal hydraulic extrusion
presses; high energy rate presses; manually positioned "C" frame punching and riveting presses;
meat-processing presses; forging presses and hammers; powered press brakes; metal shears; iron
workers; cold headers; die-casting machines; plastic injection molding machines; stretch forming
machines; roll-bending machines; welding machines; welding presses; radial expanding and
compression equipment; packaging machines; balers; laboratory machines or equipment used to
determine properties of materials; and guillotine paper cutters.

ANSI B11.3-2012: Safety Requirements for Power Press Brakes

Scope: The requirements of this standard apply to those machine tools

classified as power press brakes (hereinafter referred to simply as "press
brakes"), which are designed and constructed for the specific purpose of
bending material. The requirements of this standard also apply to powered
folding machines.

Excluded from the requirements of this standard are mechanical power presses; hydraulic power
presses, hand brakes; tangent benders; apron brakes; and other similar types of metal bending
machines.

ASSE has published a tech brief specifically addressing this standard.

4
 ANSI B11.4-2003 (R2013): Safety Requirements for Shears
Scope: This standard applies to those mechanically, hydraulically, hydra-
mechanically, or pneumatically powered shears used to cut material by
shearing and which utilize a fixed blade(s) and non-rotary moving blade(s).
The shears that are excluded from the requirements of this standard are
slitting-rotary, nibblers; coil slitters; portable hand tools; rotary-blade
slitters and shears; iron workers; alligator; angle, bar, bean, channel, and
notching machines.

ANSI B11.5-1988 (R2013): Ironworkers - Safety Requirements for

Construction, Care & Use

Scope: The requirements of this standard apply to those combination,

multipurpose powered machines that punch, shear, notch, cope and form
metal or other materials commonly referred to as ironworkers. The
requirements of this standard also apply to those single or multipurpose
powered machines similar in construction to, and identical in the use of, an ironworker or
portions thereof.
The ironworkers or combinations that are excluded from the requirements of this standard are:
Alligator shears; bar shears; billet shears; manually powered machines; nibblers; portable hand
tools; portable machines; power press brakes; power presses; and power shears.

ANSI B11.6-2001 (R2012): Safety Requirements for Manual

Turning Machines with or without Automatic Control

Scope: Safety Requirements for Manual Turning Machines w/

or without Auto Control This standard specifies safety
requirements for the design, construction, operation and
maintenance (including installation, dismantling, and transport)
of the general class of manually controlled horizontal and
vertical spindle turning machines. Machines covered by this
standard are intended to work metals and other manmade
materials. This standard also applies to devices that are integral
to the machine. These machines may have automatic capability but may not be equipped with
automatic part handling or barfeed mechanisms nor automatic tool changing systems.

Excluded from the requirements of this standard are NC Turning Machines where manual
control is used only to set the machine for automatic production.

ANSI B11.7-1995 (R2015): Cold Headers & Cold Formers - Safety

Requirements for Construction

Scope: The requirements of this standard apply only to those mechanically-

powered machines commonly referred to as cold headers and cold formers,
which perform many operations such as shearing, heading, upsetting,

5
extruding, trimming, forming, cold working, or warm forming material by means of tools and
dies. This type of equipment generally has the ram in a horizontal position. Included are pointers
and roll formers when they are mechanically an integral part of the basic machine.

Excluded from the requirements of the standard are: mechanical, hydraulic, and pneumatic
power presses; hot forgers; hot upsetters (including cold work); hot farmers; hot headers; vertical
cold forgers; four slide machines; swaggers; wine drawers; slotters; shavers, and high-energy
machines. Also excluded are pointers and roll formers, unless they are an integral part of the
basic machine.

ANSI B11.8-2001 (R2012): Safety Requirements for Manual Milling,

Drilling & Boring Machines with or without Automatic Control

Scope: This standard specifies safety requirements for the design,

construction, operation and maintenance (including installation, dismantling
and transport) of manually controlled milling, drilling, and boring
machines. This standard also applies to devices that are integral to the
machine. These machines may have automatic capability but may not be equipped with
automatic tool changing or automatic part handling systems.

Excluded from the requirements of this standard are NC milling, drilling, and boring machines
where manual control is used only to set the machine for automatic production.

ANSI B11.9-2010 (R2015): Safety Requirements for Grinding

Machines

Scope: This standard applies to all stationary grinding machines, used in

either industrial or commercial applications that utilize an abrasive product
to change the shape, size or surface finish of any material. This standard
also applies to these machines when they are grinding materials other than
metals such as glass, ceramics, plastics, and rubber.

Excluded from the requirements of this standard are: portable hand-held grinding machines,
machines using loose abrasives, machines used in wood-working applications, or machines used
for concrete cutting in road construction. Also, this standard does not apply to honing machines,
lapping machines, polishing machines or belt grinding machines.

ANSI B11.10-2003 (R2015): Safety Requirements for Metal Sawing

Machines

Scope: This standard specifies safety requirements for the design,

construction, modification, operation and maintenance (including
installation, dismantling and transport) of a general class of stationary

6
machine tools that use a saw blade (tool) to cut off or change the shape of the workpiece. This
standard also applies to ancillary devices integrated into the machine (e.g., part handling
mechanisms, chip handling systems).

Excluded from the requirements of this standard are: woodworking/sawing machines;

stonecutting sawing machines; food-processing sawing machines; abrasive-sawing machines;
and portable by-hand sawing machines

ANSI B11.11-2001 (R2012): Safety Requirements for Gear and Spline

Cutting Machines

Scope: This standard specifies safety requirements for the design,

construction, operation and maintenance (including installation, dismantling
and transport) of gear and spline cutting machines (see 3.1). The
requirements of this standard apply to machines with single or multiple
spindles that are specifically constructed to produce gear teeth by the process of hobbing,
milling, shaping, and broaching. It also applies to those machines that shave, hone, lap, or
chamfer gear teeth and machines used to produce ratchet, spline, or sprocket teeth. The
requirements of this standard do not apply to machines used for molding, rolling, flame cutting,
gear grinding, stamping, impact forming, forging, and gear inspection. Power tools, portable by
hand are also excluded from this standard.

ANSI B11.15-2001 (R2012): Safety Requirements for Pipe, Tube and

Shape Bending Machines

Scope: The requirements of this standard apply to any power-driven

machine designed for bending pipe, tube, and shapes by means of bending
dies, clamp dies, pressure dies, mandrels, wiper dies, vertical bending
punches, radius dies, wing dies, and associated tooling.

Excluded from the requirements for this standard are: Bench presses; hydro forming; forging
presses; four-slide machines; hydraulic presses; mechanical presses; power press brakes; roll
benders; roll formers; and assembly machines.

ANSI B11.16-2014: Safety Requirements for Powder/Metal

Compacting Presses

Scope: The requirements of this standard apply to those mechanically,

hydraulically or direct drive machines that are designed, modified, or
converted for the purpose of compressing metallic or nonmetallic powders.
These machines are commonly referred to as metal powder presses, powder
metal presses, compacting presses, pill presses, rotary PM presses, PM briquetting presses,

7
powder metal forging presses, metal powder sizing presses or metal powder coining presses. For
the purpose of this standard, they shall be referred to as "PM presses." PM press axes can be of a
direct driven type.

Excluded from this standard are: mechanical and hydraulic power press brakes; mechanical and
hydraulic power presses; bulldozers; conventional hot bending and hot metal presses;
conventional forging presses; hammers; riveting machines and similar types of fastener
applications; isostatic and hydrostatic presses; high energy rate presses.

ANSI B11.17-2004 (R2015): Safety Requirements for Horizontal

Hydraulic Extrusion Presses

Scope: The requirements of this standard apply to those horizontal

hydraulically powered presses that extrude metals by means of applying
sufficient pressure to an individual metal billet, confined within a container,
to force the metal to be extruded through the configured openings of a die.
Included are horizontal hydraulically powered presses that produce extruded shapes by the
extrusion process, either direct or indirect.

Excluded from the requirements for this standard are: hydrostatic extrusion presses; vertical
extrusion presses; laboratory presses used to develop extrusion techniques for new materials and
products; and extruding machines of unconventional design.

ANSI B11.18-2006 (R2012): Safety Requirements for Machines

Processing or Slitting Coiled or Non-coiled Metal

Scope: This standard applies to machines, and groups of machines

arranged in production systems, for processing strip, sheet, or plate metal
from a coiled or non-coiled configuration through machines that size or
otherwise convert the metal into desired configurations. The terms "strip,
sheet or plate" are used interchangeably without dimensional implications. Typical machinery
systems include: cut-to-length lines; press feed lines; and slitting lines.

Specifically excluded from this standard are machinery and devices for the sole purpose of
performing thermal, coating, chemical, and electrolytic processes and any emissions therefrom
are commonly associated with metal processing systems. This standard does not provide safety
requirements for these specific processes or devices.

8
 ANSI B11.19-2010: Performance Requirements for Safeguarding

Scope: This standard provides performance requirements for the design,

construction, installation, operation and maintenance of the safeguarding
listed below when applied to machines.

a) Guards;
b) Safeguarding devices;
c) Awareness devices;
d) Safeguarding methods.

This standard also provides performance requirements for complementary equipment and
measures, safe work procedures, and safety functions.

This standard does not provide the requirements for the selection of the safeguarding for a
particular application.

ANSI B11.20-2004 (R2015): Safety Requirements for Integrated

Manufacturing Systems

Scope: This standard specifies the safety requirements for the design,
construction, set-up, operation and maintenance (including installation,
dismantling and transport) of integrated manufacturing systems.

This standard does not cover: safety aspects of individual machines and equipment that may be
covered by standards specific to those machines and equipment (B11_ base_ standard), transfer
machines or transfer lines, or continuous flow processes.

ANSI B11.21-2006 (R2012): Safety Requirements for Machine Tools

Using Lasers for Processing Materials

Scope: This standard applies to machine tools using a laser for processing
materials, and its associated equipment. It describes the hazards generated
by such machines and states the protective measures to be incorporated into
such machines. The standard also contains requirements for the information
provided with such machines.

Excluded from the requirements of this document are: photolithography; holography; equipment
used in medical applications; data storage; laser printers; and copiers.

9
 ANSI B11.22-2002 (R2012): Safety Requirements for Turning Centers
& Automatic Numerically Controlled Turning Machines

Scope: This standard specifies the safety requirements for the design,
construction, operation and maintenance (including installation, dismantling
and transport) of turning centers and automatic numerically controlled
turning machines.

This standard does not cover safety requirements of manufacturing systems/cells (integrated
manufacturing systems, B11.20).

ANSI B11.23-2002 (R2012): Safety Requirements for Machining

Centers and Automatic Numerically Controlled Milling, Drilling and
Boring Machines

Scope: This standard specifies the safety requirements for the design,
construction, operation and maintenance (including installation,
dismantling, and transport) of machining centers and automatic numerically
controlled milling, drilling and boring machines.
This standard is applicable to machines where the axes of travel is not greater than 1x1x1 m
(39x39x39 in).

ANSI B11.24-2002 (R2012): Safety Requirements for Transfer

Machines

Scope: This standard specifies the safety requirements for the design,
construction, operation and maintenance (including installation,
dismantling, and transport) of machining centers and automatic numerically
controlled milling, drilling and boring machines.
This standard is applicable to machines where the axes of travel is not greater than 1x1x1 m
(39x39x39 in).

ANSI B11.25-2015: Safety Requirements for Large Machines

Scope: This standard applies to machines with a work envelope equal to or

greater than two cubic meters (2 m3) or two meters of linear axis travel, or
where personnel are regularly required to enter into the working envelope
to perform work or tasks.

The requirements in this standard apply to all large machines, unless they are specifically
covered in or by another standard. This document is intended to be used with both ANSI B11.0

10
and ANSI B11.19 to execute the risk assessment process and the safeguarding of machinery
respectively.

The requirements of this standard do not apply to turning machines and turning centers designed
to accept work holding devices less than 500 mm (20 inches) outside diameter and with a
distance between centers less than 2 meters (80 inches).

ANSI B11.TR1-2004: Ergonomic Guidelines for the Design,

Installation & Use of Machine Tools

Scope: The purpose of this guideline is to provide a uniform approach to

ergonomic considerations for machine tools within the workplace. This
document addresses those considerations which will assist in design,
installation and use of manufacturing systems, including individual and integrated machine tools
and auxiliary components.

ANSI B11.TR2-1997: Mist Control Considerations for the Design,

Installation & Use of Machine Tools Using Metalworking Fluids

Scope: This document provides guidelines for a uniform approach to the

control of airborne contaminants generated by stationary machine tools
used to cut and form materials. Control shall be through the proper design,
installation, use, and maintenance of the machine tool and its support
systems (such as, but not limited to, metalworking fluid delivery systems and air cleaning
equipment).

ANSI B11.TR3-2000: Risk Assessment & Risk Reduction-A Guideline

to Estimate, Evaluate & Reduce Risks Associated with Machine Tools

Scope: This B11 Technical Report provides a means to identify hazards

associated with a particular machine or system when used as intended, and
provides a procedure to estimate, evaluate, and reduce the risks of harm to
individuals associated with these hazards under the various conditions of
use of that machine or system.

ANSI B11.TR4-2004 Selection of Programmable Electronic Systems

(PES/PLC) for Machine Tools

Scope: The purpose of this Technical Report is to provide guidance for the
design or selection, integration, and validation of PESs for the safety related
functions of a machine production system. The terminology used in this
document may not be used consistently throughout the industry, but this

11
document does represent the concepts which are important when using and designing safety-
related control systems.

ANSI B11.TR5-2006: Sound (Noise) Level Measurement Guidelines

Scope: The purpose of this Technical Report is to specify methods for

measuring, evaluating and documenting sound levels emitted by a machine
or machine production system(s) during normal operation and when
running at idle, and to establish recommended sound levels at the various
measurement locations around the machine or machine production system.

ANSI B11.TR6-2010: Safety Control Systems for Machines

Scope: This Technical Report provides guidance in understanding and

implementing safety-related control functions (functional safety) as they
relate to electrical, electronic, mechanical, pneumatic, hydraulic
components and systems for machine tools covered by the B11 series of
safety standards.

NOTE 1: The terminology used in this document may not be used consistently throughout the
industry, but this document does represent concepts which are important when using and
designing safety-related control systems.

NOTE 2: Usage of [machine] in the following text means any of the specific machine tools
covered by the ANSI B11 base' series of safety standards.

NOTE 3: This document is not intended to address programmable electronic systems /

programmable electronic devices (PES / PED). See B11.TR4.

ANSI B11.TR7-2007: Designing for Safety and Lean Manufacturing: A

guide on integrating safety & lean manufacturing principles in the use
of machinery

Scope: This document provides guidance on the practical application and

integration of safety and lean manufacturing principles to machinery and
manufacturing systems for improving performance, safety and quality by
reducing injury and waste. The guidelines in this technical report assist machine tool users to
minimize waste and risk associated with machinery and manufacturing systems, including
individual and integrated machine tools and auxiliary components.

12
Links and information related to the ANSI B11 American National Standard

Essential Requirements used by ANSI

The links below will give information addressing how voluntary national consensus
standards are used in regulatory settings:

www.asse.org/assets/1/7/Dembystandardsarticle3-21-2006.doc

http://www.ansi.org/news_publications/other_documents/safeguarding.aspx?menuid=7

There is an official memorandum of understanding between OSHA and ANSI. The link
to the read the memorandum is at:

http://www.osha.gov/pls/oshaweb/owadisp.show_document?p_table=MOU&p_id=323

There are dozens of examples of how the B11 Standards are recognized by OSHA. Below are
two examples:

http://www.osha.gov/pls/oshaweb/owadisp.show_document?p_table=INTERPRETATIONS&p_
id=19422

https://www.osha.gov/SLTC/etools/machineguarding/bibliography.html

From the U.S. Occupational Safety and Health Review Commission:

http://www.oshrc.gov/decisions/html_1976/8597.html

From the State of California:

http://www.dir.ca.gov/oshsb/GP_Die_ISOR.pdf

From CDC/NIOSH:

http://www.cdc.gov/niosh/nioshtic-2/20031240.html

From the State of Oregon:

http://www.osha.oregon.gov/pdf/pds/pd-217.pdf

13
 In regards to 5A1 citations, B11 Standards are used extensively. Below is an example from the
B11.3 Standard. The most recent inquiry indicates that B11.3 alone has been referenced 160
times at the level of Federal OSHA. Some examples are below:

By Date
Inspection Citation Issuance Report ID Category SIC Establishment Name
1 315739847 01001 03/20/2012 0418100 Falling 3511 D & D Manufacturing Company, Inc.
2 316226703 01001 01/26/2012 0213600 Guarding 3499 Truform Manufacturing Corp.
3 315977652 01001 01/18/2012 0213900 Guarding 3443 Kiker Sheet Metal Inc.
4 113740690 01001 11/18/2011 0316700 Crushing 2541 Fleetwood Industries, Incorporated
5 315552109 01001A 10/04/2011 0522300 Crushing 3496 Advance Wire Forming
6 315568428 01001 10/03/2011 0213900 Unclass 3499 Crest Ultrasonics Corp.
7 315717173 01001 09/30/2011 0213900 Cuts 3412 Sp Sheet Metal Company
8 315717173 01007A 09/30/2011 0213900 Cuts 3412 Sp Sheet Metal Company
9 314723966 01001 09/21/2011 0317900 Guarding 3599 Stanley Vidmar
10 314723966 01002 09/21/2011 0317900 Guarding 3599 Stanley Vidmar
11 314890450 02001 06/30/2011 0953220 Falling 3442 Arcadia, Inc.
12 315361717 01001 06/28/2011 0420600 Electric 3442 Quality Engineered Products Corp.
13 315487264 01001 06/27/2011 0213900 Guarding 3499 Compass Wire Cloth Corporation
14 314378795 01001 06/10/2011 0453710 Crushing 3568 Fenner,Inc., Dba Fenner Drives
15 314371691 01001 06/09/2011 0453710 Crushing 2011 The Smithfield Packing Company, Incorporated
16 315523084 01001 05/10/2011 0111100 Falling 3499 Saunders Mfg. Co. Inc.
17 315156919 01001 05/02/2011 0521700 Falling 3446 David Architectural Metals, Inc.
18 314205840 01001 04/19/2011 0418100 Crushing 3444 Don Park (Usa) Limited Partnership
19 314205840 01002 04/19/2011 0418100 Lifting 3444 Don Park (Usa) Limited Partnership
20 314205840 01003 04/19/2011 0418100 Falling 3444 Don Park (Usa) Limited Partnership

14