Specifications :

l Measuring method TRMS using microcontroller

l Display type RED LED Super Bright Display
4 Digit Programmable l Maximum Display 0-9999 counts (4 Digit)
Overrange Indication -OL-
Voltmeter
l
l Under range Indication -UL-
MODEL : SMP35SN l Resolution 0.1 to 1 (depending on PTR)
l Accuracy 0.5% FSD
l Sampling Rate 2.5 Sampler/Second
l Maximum Overload 1.2 times continuous
l Faceplate/Lens Red Antiglare Faceplate with
Annunciators
l Mounting Clamps Sturdy, Derlin (Engineering
plastic)
l VA Burden (Typical) Auxiliary : < 1.5VA
Input : < 0.5VA
l Frequency Response 45-65Hz
l Environmental conditions 0 to 550C, <70% RH (Operation)
-10 to 700C, <70%RH (Storage)
l Dielectric strength 2.5 KV at 50Hz for 1 minute
between Input, Auxiliary & Case
l Impulse withstand 3.5KV, 1.2/50 S.
l Case/Housing Material Black ABS, Dimension as per
DIN 43700
l Connectors Terminal Block : Thermoplastic
(UL 94V-0) With Tin Plated Brass
Terminals
l Display Stability Within 2 digits
l Display Digit Height 0.56" / 14.2mm
l Auxiliary Supply (Dual) 230V AC 10% / 110V AC 10%
@ 50 Hz
USER MANUAL (V1.2) 2

Terminal Connection start displaying measured readings.)

Aux. Supply (any one only) Press "P" key to configure PT ratio.
230V AC
Meter will display "0001" with right most digit i.e. "1" will be blinking.
IN IN 110V
(LO) (HI) N AC L L To change digit 0 to 9 use "" Key and to shift left use "" Key.
Enter required PT ratio.
e.g. if PT is 33KV / 110V then
PT ratio = PT primary / PT secondary.
Power ON the meter, meter will display measured readings. PT ratio = 33000 / 110 = 300.
Default Factory Setting : To enter the PT ratio with decimal point, press "" key after left
PTR : 1 most digit starts blinking. Now no digit will blink. Press "" key to
Programming Mode : change decimal point. Initially decimal point will appear at second
digit from right side. Press "" key to shift decimal point left side.
To configure the meter, Press "P" key, the meter will display
After decimal point reaches at left most digit if user presses ""
"----". Enter the Password to configure the meter. Password is
key decimal point will disappear. Press "P" to enter. Now meter
"4321".
will display the measured values. For Measured Value > 9999,
If it is not required to configure the meter press "P" key again, the LED for "K" (Kilo) will glow.
meter will start displaying measured reading.
To change digit 0 to 9 use "" Key and to shift left use "" Key. TEST RESULTS :
e.g. Enter Password "4321". INPUT (V) 0 50 100 150 200 250 300 350 400 450 500
Press "" key "---1"
RESULT UL OK OK OK OK OK OK OK OK OK OK
Press "" key followed by "" key "--11"
Press "" key again "--21"
Press"" key followed by "" key "-121"
Press ""key again "-221"
Press ""key again "-321"
Press ""key followed by "" key "1321" MECO INSTRUMENTS PRIVATE LTD.
Press ""key again "2321"
Plot No. EL-1, MIDC Electronic Zone, TTC Industrial Area,
Press ""key again "3321" Mahape, Navi Mumbai - 400710 (INDIA)
Press ""key again "4321" Tel : 0091-22-27673311-16, 27673300 (Board)
Press "P" key to enter setup. Meter will display "Ptr". Fax : 0091-22-27673310, 27673330
(If entered password is wrong and "P" key is pressed, meter will E-mail : [email protected] Web : www.mecoinst.com

3 4
 Specifications :
l Measuring method TRMS using microcontroller
l Display type RED LED Super Bright Display
4 Digit Programmable l Maximum Display 0-9999 counts (4 Digit)
Overrange Indication -OL-
Ammeter
l
l Under range Indication -UL-
MODEL : SMP35SN l Resolution 0.001 to 1 (depending on CTP)
l Accuracy 0.5% FSD
l Sampling Rate 2.5 Samples/Second
l Maximum Overload 2 times continuous
l Faceplate/Lens Red Antiglare Faceplate with
Annunciators
l Mounting Clamps Sturdy, Derlin (Engineering
plastic)
l VA Burden (Typical) Auxiliary : < 1.5VA
Input : < 0.5VA
l Frequency Response 45-65Hz
l Environmental conditions 0 to 550C, <70% RH (Operation)
-10 to 700C, <70%RH (Storage)
l Dielectric strength 2.5 KV at 50Hz for 1 minute
between Input, Auxiliary & Case
l Impulse withstand 3.5KV, 1.2/50 S.
l Case/Housing Material Black ABS, Dimension as per
DIN 43700
l Connectors Terminal Block : Thermoplastic
(UL 94V-0) With Tin Plated Brass
Terminals
l Display Stability Within 2 digits
l Display Digit Height 0.56" / 14.2mm
l Auxiliary Supply (Dual) 230V AC 10% / 110V AC 10%
@50 Hz
USER MANUAL (V1.2) 2

Terminal Connection Note : If the selected range is 5A then short the jumper J2
Aux. Supply (any one only) provided at front PCB in the meter.
230V AC If the selected range is 1A then open the jumper J2 provided
IN IN 110V at front PCB in the meter. Remove filter plate to open/
(LO) (HI) N AC L L
short J2 jumper.
Meter will display "Ctp". Press "P" key to configure the CT
primary. Meter will display "0001" with right most digit i.e. "1" will
Power ON the meter, meter will display measured readings. be blinking.
Default Factory Setting : Note : In case of 5A range CT primary should be greater
A1 / A5 : A5 (5A Range) than or equal to 5.
CTP : 5 To change digit 0 to 9 use "" Key and to shift left use "" Key.
Programming Mode : Enter required CT primary.
To configure the meter, Press "P" key, the meter will display e.g. If CT being used is 1000/5A user should enter 1000 as
"----". Enter the Password to configure the meter. Password is CT primary. Selected current range should be A 5 (i.e. 5A
"4321". If it is not required to configure the meter press "P" key range).
again, meter will start displaying measured reading. To enter the CT primary with decimal point, press, "" key after
To change digit 0 to 9 use "" Key and to shift left use "" Key. left most digit starts blinking. Now no digit will blink. Press ""
key to change decimal point. Initially decimal point will appear at
e.g. Enter Password "4321".
second digit from right side. Press "" key to shift decimal
Press "" key "---1"
point left side. After decimal point reaches at left most digit if
Press "" key followed by "" key "--11" user presses "" key decimal point will disappear. Press "P"
Press "" key again "--21" Key to enter. Now meter will display the measured values. For
Press"" key followed by "" key "-121" Measured Value > 9999, the LED for "K" (Kilo) will glow.
Press ""key again "-221"
TEST RESULTS :
Press ""key again "-321"
Press ""key followed by "" key "1321" INPUT (5A) 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Press ""key again "2321" INPUT (1A) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Press ""key again "3321"
RESULT UL OK OK OK OK OK OK OK OK OK OK
Press ""key again "4321". Press "P" key to enter setup.
Use "" key to change between "A 1" and "A 5" (1A range or 5A
range). (If entered password is wrong and "P" key is pressed, MECO INSTRUMENTS PRIVATE LTD.
meter will start displaying measured readings.) Plot No. EL-1, MIDC Electronic Zone, TTC Industrial Area, Mahape, Navi Mumbai - 400710 (INDIA)
Press "P" key to enter the desired range. Tel : 0091-22-27673311-16, 27673300 (Board) Fax : 0091-22-27673310, 27673330
3 E-mail : [email protected] Web : www.mecoinst.com 4

15102010
Note : If the selected range is 5A then short the jumper
1A/5A provided at front PCB in the meter.
If the selected range is 1A then open the jumper 1A/5A
provided at front PCB in the meter. Remove filter plate to
open/short 1A/5A jumper. 4 Digit Programmable
Meter will display "Ctp". Press "P" key to configure the CT Ammeter
primary. Meter will display "0001" with right most digit i.e. "1" will
be blinking. MODEL : SMP9635SN
Note : In case of 5A range CT primary should be greater
than or equal to 5.
To change digit 0 to 9 use "" Key and to shift left use "" Key.
Enter required CT primary.
e.g. If CT being used is 1000/5A user should enter 1000 as
CT primary. Selected current range should be A 5 (i.e. 5A
range).
To enter the CT primary with decimal point, press, "" key after
left most digit starts blinking. Now no digit will blink. Press ""
key to change decimal point. Initially decimal point will appear at
second digit from right side. Press "" key to shift decimal
point left side. After decimal point reaches at left most digit if
user presses "" key decimal point will disappear. Press "P"
Key to enter. Now meter will display the measured values. For
Measured Value > 9999, the LED for "K" (Kilo) will glow.
TEST RESULTS : Meter Serial No. ..........................................

INPUT (5A) 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
INPUT (1A) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
RESULT UL OK OK OK OK OK OK OK OK OK OK

MECO INSTRUMENTS PRIVATE LTD.

Plot No. EL-1, MIDC Electronic Zone, TTC Industrial Area, Mahape, Navi Mumbai - 400710 (INDIA)
Tel : 0091-22-27673311-16, 27673300 (Board) Fax : 0091-22-27673310, 27673330
E-mail : [email protected] Web : www.mecoinst.com USER MANUAL (V1.3)
4 1

Specifications : Terminal Connection

Aux. Supply (any one only)
l Measuring method TRMS using microcontroller 230V AC
l Display type RED LED Super Bright Display 110V
IN IN
l Maximum Display 0-9999 counts (4 Digit) (LO) (HI) N AC L L

l Overrange Indication -OL-

l Under range Indication -UL-
l Resolution 0.001 to 1 (depending on CTP) Power ON the meter, meter will display measured readings.
l Accuracy 0.5% FSD Default Factory Setting :
l Sampling Rate 2.5 Samples/Second A1 / A5 : A5 (5A Range)
l Maximum Overload 2 times continuous CTP : 5
l Faceplate/Lens Red Antiglare Faceplate with Programming Mode :
Annunciators To configure the meter, Press "P" key, the meter will display
l Mounting Clamps Sturdy, Derlin (Engineering "----". Enter the Password to configure the meter. Password is
plastic) "4321". If it is not required to configure the meter press "P" key
l VA Burden (Typical) Auxiliary : < 1.5VA again, meter will start displaying measured reading.
Input : < 0.5VA To change digit 0 to 9 use "" Key and to shift left use "" Key.
l Frequency Response 45-65Hz e.g. Enter Password "4321".
l Environmental conditions 0 to 550C, <70% RH (Operation) Press "" key "---1"
-10 to 700C, <70%RH (Storage) Press "" key followed by "" key "--11"
l Dielectric strength 2.5 KV at 50Hz for 1 minute Press "" key again "--21"
between Input, Auxiliary & Case Press"" key followed by "" key "-121"
l Impulse withstand 3.5KV, 1.2/50 S. Press ""key again "-221"
l Case/Housing Material Black ABS, Dimension as per Press ""key again "-321"
DIN 43700 Press ""key followed by "" key "1321"
l Connectors Terminal Block : Thermoplastic Press ""key again "2321"
(UL 94V-0) With Tin Plated Brass Press ""key again "3321"
Terminals Press ""key again "4321". Press "P" key to enter setup.
l Display Stability Within 2 digits Use "" key to change between "A 1" and "A 5" (1A range or 5A
l Display Digit Height 0.56" / 14.2mm range). (If entered password is wrong and "P" key is pressed,
l Auxiliary Supply (Dual) 230V AC 10% / 110V AC 10% meter will start displaying measured readings.)
@50 Hz Press "P" key to enter the desired range.

2 3

SMP9635SN-A : 28-09-2012
start displaying measured readings.)
Press "P" key to configure PT ratio.
Meter will display "0001" with right most digit i.e. "1" will be blinking.
To change digit 0 to 9 use "" Key and to shift left use "" Key.
Enter required PT ratio.
4 Digit Programmable
e.g. if PT is 33KV / 110V then Voltmeter
PT ratio = PT primary / PT secondary. MODEL : SMP9635SN
PT ratio = 33000 / 110 = 300.
To enter the PT ratio with decimal point, press "" key after left
most digit starts blinking. Now no digit will blink. Press "" key to
change decimal point. Initially decimal point will appear at second
digit from right side. Press "" key to shift decimal point left side.
After decimal point reaches at left most digit if user presses ""
key decimal point will disappear. Press "P" to enter. Now meter
will display the measured values. For Measured Value > 9999,
the LED for "K" (Kilo) will glow.

TEST RESULTS : Meter Serial No. ..........................................

INPUT (V) 0 50 100 150 200 250 300 350 400 450 500
RESULT UL OK OK OK OK OK OK OK OK OK OK

MECO INSTRUMENTS PRIVATE LTD.

Plot No. EL-1, MIDC Electronic Zone, TTC Industrial Area,
Mahape, Navi Mumbai - 400710 (INDIA)
Tel : 0091-22-27673311-16, 27673300 (Board)
Fax : 0091-22-27673310, 27673330
E-mail : [email protected] Web : www.mecoinst.com

USER MANUAL (V1.3)

Specifications : Terminal Connection

Aux. Supply (any one only)
l Measuring method TRMS using microcontroller 230V AC
l Display type RED LED Super Bright Display 110V
IN IN
l Maximum Display 0-9999 counts (4 Digit) (LO) (HI) N AC L L
l Overrange Indication -OL-
l Under range Indication -UL-
l Resolution 0.1 to 1 (depending on PTR)
l Accuracy 0.5% FSD Power ON the meter, meter will display measured readings.
l Sampling Rate 2.5 Sampler/Second Default Factory Setting :
l Maximum Overload 1.2 times continuous PTR : 1
l Faceplate/Lens Red Antiglare Faceplate with Programming Mode :
Annunciators To configure the meter, Press "P" key, the meter will display
l Mounting Clamps Sturdy, Derlin (Engineering "----". Enter the Password to configure the meter. Password is
plastic) "4321".
l VA Burden (Typical) Auxiliary : < 1.5VA If it is not required to configure the meter press "P" key again,
Input : < 0.5VA meter will start displaying measured reading.
l Frequency Response 45-65Hz To change digit 0 to 9 use "" Key and to shift left use "" Key.
l Environmental conditions 0 to 550C, <70% RH (Operation) e.g. Enter Password "4321".
-10 to 700C, <70%RH (Storage) Press "" key "---1"
l Dielectric strength 2.5 KV at 50Hz for 1 minute Press "" key followed by "" key "--11"
between Input, Auxiliary & Case Press "" key again "--21"
l Impulse withstand 3.5KV, 1.2/50 S. Press"" key followed by "" key "-121"
l Case/Housing Material Black ABS, Dimension as per Press ""key again "-221"
DIN 43700 Press ""key again "-321"
l Connectors Terminal Block : Thermoplastic Press ""key followed by "" key "1321"
(UL 94V-0) With Tin Plated Brass Press ""key again "2321"
Terminals Press ""key again "3321"
l Display Stability Within 2 digits Press ""key again "4321"
l Display Digit Height 0.56" / 14.2mm Press "P" key to enter setup. Meter will display "Ptr".
l Auxiliary Supply (Dual) 230V AC 10% / 110V AC 10% (If entered password is wrong and "P" key is pressed, meter will
@ 50 Hz

SMP9635SN-V : 28-09-2012