Control of Corrosion On Underwater Pile1

Control Of Corrosion On Underwater
Piles
Abstract
Piles are structures used to transfer loads from superstructure to the sub
surface strata. When the subsurface stratum is water based or if we deal with a
hydraulic structure, the piles are to be driven into water and under water strata.
Piles used in underwater structures are often subjected to corrosion. There is no
absolute way to eliminate all corrosion; but corrosion protection measures are
employed to control the effect of corrosion.
Corrosion protection can be in different ways according to the environment and

other factors. Forms of corrosion protection include the use of inhibitors,
surface treatments, coatings and sealants Piles are structures used to transfer
loads from superstructure to the sub, cathodic protection and anodic protection.
The control measures explained in this are Protective coatings, cathodic
treatment and application of Fibre Re-inforced Polymer (FRP) Composites
Corrosion Mechanism Of Steel In Sea Water
On steel piling in seawater, the more chemically active surface areas (anodes)
are metallically coupled through the piling itself to the less chemically active
surface areas (cathodes) resulting in a flow of electricity and corrosion of the
anodic areas. General surface roughening occurs when these local anodic and
cathodic areas continually shift about randomly during the corrosion process.
Sometimes these active local areas do not shift position end, therefore, the metal
suffers localized attack and pitting occurs. In general, the depth of pitting is
related to the ratio of the anodic sites to the area of cathodic site in contact with
the electrolyte (seawater). The smaller the anode area relative to the cathode
area, the deeper the pitting
Corrosion Management
Before deciding on the methods for control of corrosion to be applied,

conceptual and feasibility studies have been carried out. Typically, corrosion
management can be divided into three major phases
.
Phase 1 of the program is the programmatic assessment of the project. This
phase is the planning stage for a corrosion management program to take
place. It initiates the program to be implemented on structures that are found
to be under the threat of corrosion. For the planning stage, three main
requirements are sought, namely the strategy, budget and schedule needed to
overcome the problem raised from corrosion of reinforcement. This is seen
asan important part for an effective management program as feasibility
studies are normally conducted to determine the serviceability of the
structure after treatment.
Phase 2 of the program involves physical assessment and actual remediation.

Inspections for severity of corrosion are conducted in this phase to determine
what strategy or methods are most suitable to be applied. Development of
corrosion control strategy would present more option to the management
program. Remedial work would be carried out once the proper strategy has
been recognized.
Phase 3 of the program mainly deals with future monitoring of the repaired
structure. Currently and historically, most of the corrosion control programs
are driven by response to incident or urgent need, rather than systematically
identifying and managing the existing resources. This can be overcome by
implementing internal or external monitoring system using current
technology practiced in oil and gas industries
seen an important part for an effective management program as feasibility


been recognized.
as an important part for an effective management program as feasibility

been recognized.
Zones Of Corrosion Of Steel Piles
Examination of corroded marine piles reveals several distinct areas of attack. It

is convenient to divide these areas into five zones, each having a characteristic
corrosion rate as shown in Fig
Control Of Corrosion
CORROSION PROTECTION METHODS
2.1 Protective Coating
In order to protect metals from corrosion, the contact between the metal and the
corrosive environment is to be cut off. This is done by coating the surface of
metals with a continuous non-porous material inert to the corrosive atmosphere.
Surface coatings are broadly classified into three

a). Metallic coatings
b). Inorganic Coatings
c). Organic Coatings

Individual coatings are formulated to perform specific functions and must be
selected to become components of a total system designed for optimum results
considering the environment and service expectations.
The different types of coatings used for under water piles are:
2.1.1 Inorganic Zinc Silicates Primers
Steel structures that are permanently immersed in sea water, such as jackets in
the area below the Splash Zone, are typically not coated for various reasons and
protected solely by cathodic protection systems consisting of sacrificial anodes
or impressed current arrays, which can be maintained as required by underwater
contractors. Various anticorrosive pigmented primers are available, some that
passivate the steel but the most effective are inorganic zinc silicate primers
which essentially become anodic to the steel in a corrosion cycle. The primary
advantage of this type of coating is that it will arrest rust creep, or undercutting
of the coatings surrounding the damaged area, and confine corrosion to the
point of the damage. These coatings also provide a high degree of resistance to
heat and chemical spills.
2.1.2 High Build Epoxy Coatings
Epoxies are generally more abrasion and chemical resistant than primers and
topcoats and in this case protect not only the substrate itself, but the zinc primer
as well from all of these detrimental factors. However, one drawback with
epoxy coatings is very poor resistance to ultra violet from sunlight and most
will chalk and fade rapidly. This leads to an erosion of the coatings film
thickness, reducing the barrier protection of the system.
2.1.3 Aliphatic Polyurethane Topcoats
Polyurethane finish coats are generally acknowledged as providing optimum

resistance to UV and high degrees of flexibility and chemical resistance. They
also help to maintain a very high level of cosmetic gloss and colour retention
and can be cleaned very easily, generally with low pH detergents and fresh
water pressure washing. Although polyurethane finishes offer no real
anticorrosive or barrier protection to the substrate they do provide a high level
of protection to the integrity of the coatings system.
2.1.4 Zinc Rich Epoxy Primers
Zinc modified epoxy anticorrosives will provide a high level of service and are
more tolerant to compromised surface preparation and ambient weather
conditions provided the zinc loading of the formula is sufficient. Zinc rich
epoxy is also most effective in maintaining damaged areas and breakdown of
the coatings systems applied at new construction as it is compatible with
alternate methods of surface preparation such as power tool cleaning and UHP
Hydro Blasting.
2.1.5 Non-Skid Deck Coatings
Coatings specifically designed with anti-slip properties normally incorporate

very course aggregates for an exaggerated profile. They are applied in very high
film builds and normally without a zinc rich primer. When primers are required
they are usually epoxy types.
2.2 Cathodic Protection
The preferred technique for mitigating marine corrosion, based on historical

performance and measurable results, is cathodic protection (CP) - the practice of
using electrochemical reactions to prevent the corrosion of steel structures. The
reason for increased acceptance: cathodic protection prevents corrosion on
underwater structures.
In theory and practice, the implementation of a CP system is quite simple.

Assuming you already have corroding steel in seawater, all you need is an
anode, a power supply, and engineering talent. A protective circuit is
accomplished between the anode, steel (cathode), power supply and electrolyte
(seawater).
CONCLUSION
Though there is no absolute way to eliminate all corrosion on under water piles,
there are some effective measures to control them. The cathodic protection is
found to be quite simple to employ and mostly used in marine conditions. The
protective coatings are used in vast and expensive structures. The FRP
composites have many advantages over conventional methods such that they are
light weight, possess high strength and chemical resistance and moreover have
incomparable flexibility.
Of the various ways of wrapping of FRP composites, transverse wrapping is

found to be the easiest as otherwise, the longitudinal pieces are awkward to
handle and difficult to position. Bi-directional material is the best option.
Scaffolding measures during the application of materials ensures safety and
simplifies installation. Out of the two system of FRP application, the pre-preg
system is easier to use. On-site FRP saturation can be problematic. High winds
and high tides should be avoided during the process.
REFERENCES
[1] R. Lacayo, C. Estulin, and S. Jakes, Going up and up: When height is all
that matters, Time, vol. 164/165, no. 26/1, pp. 172-173, December 2004.
[2] M. M. Ali and A. Aksamija, Toward a better urban life: Integration of cities
and tall buildings, in Proc. 4th Architectural Conference on High Rise
Buildings, pp. 1-21, Amman, Jordan, June 2008
SUBMITTED BY
STUDENTS OF FX ENGINEERING COLLEGE:

SREJA.S
3rd YEAR,
CIVIL ENGINEERING,
FX ENGINEERING COLLEGE,
TIRUNELVELI-627003

Control of Corrosion On Underwater Pile1

Uploaded by

Copyright:

Available Formats

Control of Corrosion On Underwater Pile1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Control of Corrosion On Underwater Pile1

Uploaded by

Copyright:

Available Formats

Control Of Corrosion On Underwater

Corrosion protection can be in different ways according to the environment and

Corrosion Mechanism Of Steel In Sea Water

Before deciding on the methods for control of corrosion to be applied,

Phase 2 of the program involves physical assessment and actual remediation.

seen an important part for an effective management program as feasibility

Phase 2 of the program involves physical assessment and actual remediation.

Phase 2 of the program involves physical assessment and actual remediation.

Zones Of Corrosion Of Steel Piles

Examination of corroded marine piles reveals several distinct areas of attack. It

CORROSION PROTECTION METHODS

2.1 Protective Coating

Surface coatings are broadly classified into three

b). Inorganic Coatings

c). Organic Coatings

2.1.1 Inorganic Zinc Silicates Primers

2.1.2 High Build Epoxy Coatings

2.1.3 Aliphatic Polyurethane Topcoats

Polyurethane finish coats are generally acknowledged as providing optimum

2.1.5 Non-Skid Deck Coatings

Coatings specifically designed with anti-slip properties normally incorporate

2.2 Cathodic Protection

The preferred technique for mitigating marine corrosion, based on historical

In theory and practice, the implementation of a CP system is quite simple.

Of the various ways of wrapping of FRP composites, transverse wrapping is

STUDENTS OF FX ENGINEERING COLLEGE:

You might also like