Chapter 2

Finite Element Equations for Heat Transfer

Abstract Solution of heat transfer problems is considered. Finite element equations

are obtained using the Galerkin method. The conductivity matrix for a triangular
finite element is calculated.

2.1 Problem Statement

Let us consider an isotropic body with temperature-dependent heat transfer. A basic

equation of heat transfer has the following form [15]:
 
qx qy qz T
+ + + Q = c . (2.1)
x y z t

Here, qx , qy and qz are components of heat flow through the unit area; Q =
Q(x, y, z,t) is the inner heat-generation rate per unit volume; is material density;
c is heat capacity; T is temperature and t is time. According to Fouriers law the
components of heat flow can be expressed as follows:

T
qx = k ,
x
T
qy = k , (2.2)
y
T
qz = k ,
z
where k is the thermal-conductivity coefficient of the media. Substitution of Fouriers
relations gives the following basic heat transfer equation:
     
T T T T
k + k + k + Q = c . (2.3)
x x y y z z t

13
14 2 Finite Element Equations for Heat Transfer

It is assumed that the boundary conditions can be of the following types:

1. Specified temperature
Ts = T1 (x, y, z,t) on S1 .

2. Specified heat flow

qx nx + qy ny + qz nz = qs on S2 .

3. Convection boundary conditions

qx nx + qy ny + qz nz = h(Ts Te ) on S3 ,

4. Radiation
qx nx + qy ny + qz nz = Ts4 qr on S4 ,

where h is the convection coefficient; Ts is an unknown surface temperature; Te is

a convective exchange temperature; is the StefanBoltzmann constant; is the
surface emission coefficient; is the surface absorption coefficient, and qr is the
incident radiant heat flow per unit surface area. For transient problems it is necessary
to specify an initial temperature field for a body at the time t = 0:

T (x, y, z, 0) = T0 (x, y, z). (2.4)

2.2 Finite Element Discretization of Heat Transfer Equations

A domain V is divided into finite elements connected at nodes. We shall write all
the relations for a finite element. Global equations for the domain can be assembled
from finite element equations using connectivity information.
Shape functions Ni are used for interpolation of temperature inside a finite ele-
ment:
T = [N]{T },
 
[N] = N1 N2 ... , (2.5)
 
{T } = T1 T2 ... .

Differentiation of the temperature-interpolation equation gives the following inter-

polation relation for temperature gradients:


T N1 N2


x x ...
Tx
N N
1 2
= ...{T } = [B]{T }. (2.6)

y
y y

T N1 N2


...
z z z
2.2 Finite Element Discretization of Heat Transfer Equations 15

Here, {T } is a vector of temperatures at nodes, [N] is a matrix of shape functions,

and [B] is a matrix for temperature-gradient interpolation.
Using the Galerkin method, we can rewrite the basic heat transfer equation in the
following form:
  
qx qy qz T
+ + Q + c Ni dV = 0. (2.7)
x y z t
V

Applying the divergence theorem to the first three terms, we arrive at the relations:
   
T Ni Ni Ni
c Ni dV {q}dV
t x y z
V V
 
= QNi dV {q}T{n}Ni dS,
(2.8)
V S
 
{q}T = qx qy qz ,
 
{n}T = nx ny nz ,

where {n} is an outer normal to the surface of the body. After insertion of boundary
conditions into the above equation, the discretized equations are as follows:
   
T Ni Ni Ni
c Ni dV {q}dV
t x y z
V V
 
= QNi dV {q}T {n}Ni dS (2.9)
V S1
  
+ qs Ni dS h(T Te )Ni dS ( T 4 qr )Ni dS.
S2 S3 S4

It is worth noting that

{q} = k[B]{T }. (2.10)
The discretized finite element equations for heat transfer problems have the follow-
ing form:

[C]{T } + ([Kc ] + [Kh] + [Kr ]){T }

(2.11)
= {RT } + {RQ} + {Rq} + {Rh} + {Rr },
16 2 Finite Element Equations for Heat Transfer


[C] = c[N]T [N]dV ,
V

[Kc ] = k[B]T [B]dV ,
V

[Kh ] = h[N]T [N]dS,
S3

[Kr ]{T } = T 4 [N]T dS,
S4

(2.12)
{RT } = {q}T{n}[N]T dS,
S1

{RQ } = Q[N]T dV ,
V

{Rq } = qs [N]T dS,
S2

{Rh } = hTe [N]T dS,
S3

{Rr } = qr [N]T dS.
S4

Here, {T } is a nodal vector of temperature derivatives with respect to time.

2.3 Different Type Problems

Equations for different types of problems can be deducted from the above general
equation:
Stationary linear problem

([Kc ] + [Kh ]){T } = {RQ } + {Rq} + {Rh}. (2.13)

Stationary nonlinear problem

([Kc ] + [Kh] + [Kr ]){T }

(2.14)
= {RQ (T )} + {Rq(T )} + {Rh(T )} + {Rr (T )}.
2.4 Triangular Element 17

Transient linear problem

[C]{T (t)} + ([Kc ] + [Kh (t)]){T (t)}

(2.15)
= {RQ (t)} + {Rq(t)} + {Rh(t)}.

Transient nonlinear problem

[C(T )]{T } + ([Kc (T )] + [Kh (T,t)] + [Kr (T )]){T }

(2.16)
= {RQ (T,t)} + {Rq(T,t)} + {Rh(T,t)} + {Rr(T,t)}.

2.4 Triangular Element

Calculation of element conductivity matrix [kc ] and heat flow vector {rq } is illus-
trated for a two-dimensional triangular element with three nodes. A simple triangu-
lar finite element is shown in Figure 2.1. The temperature distribution T (x, y) inside
the triangular element is described by linear interpolation of its nodal values:

T (x, y) = N1 (x, y)T1 + N2 (x, y)T2 + N3 (x, y)T3 ,

(2.17)
Ni (x, y) = i + i x + i y.

Interpolation functions (usually called shape functions) Ni (x, y) should satisfy the
following conditions:
T (xi , yi ) = Ti , i = 1, 2, 3. (2.18)
Solution of the above equation system provides expressions for the shape functions:

y 3

1
x

Fig. 2.1 Triangular finite element

18 2 Finite Element Equations for Heat Transfer

y 2
t
1
L

x
Fig. 2.2 Integration along an element side

1
Ni = (ai + bi x + ci y),
2
ai = xi+1 yi+2 xi+2 yi+1 ,
bi = yi+1 yi+2, (2.19)
ci = xi+2 xi+1 ,
1
= (x2 y3 + x3y1 + x1y2 x2 y1 x3 y2 x1 y3 ),
2
where is the element area.
The conductivity matrix of the triangular element is determined by integration
over element area A (assuming that the element has unit thickness),

[kc ] = k[B]T [B]dxdy. (2.20)
A

The temperature differentiation matrix [B] has expression

N1 N2 N3
x x x  
1 b1 b2 b3
[B] = = . (2.21)
N1 N2 N3 2 c1 c2 c3
y y y
Since the temperature differentiation matrix does not depend on coordinates, inte-
gration of the conductivity matrix is simple;
2
b1 + c21 b1 b2 + c1c2 b1 b3 + c1 c3
k
[kc ] = b1 b2 + c1 c2 b22 + c22 b2 b3 + c2 c3 . (2.22)
4
b1 b3 + c1 c3 b2 b3 + c2c3 b23 + c23

The heat-flow vector {rq } is evaluated by integration over the element side, as
shown in Figure 2.2
Problems 19
  1
{rq } = qs [N]T dL = qs [N1 N2 ]T Ldt. (2.23)
L 0

Here, integration over an element side L is replaced by integration using variable

t ranging from 0 to 1. Shape functions N1 and N2 on element side 12 can be ex-
pressed through t:
N1 = 1 t, N2 = t. (2.24)
After integration with substituting integration limits, the heat-flow vector equals
 
L 1
{rq } = qs . (2.25)
2 1

Element matrices and vectors are calculated for all elements in a mesh and assem-
bled into the global equation system. After application of prescribed temperatures,
solution of the global equation system produces temperatures at nodes.

Problems

2.1. Calculate matrix [kh ] describing convection boundary conditions


[kh ] = h[N]T [N]dL
L

for a side of a triangular element (see Figure 2.2).

2.2. Obtain shape functions N1 , N2 , N3 and N4 for the square element shown below.
y

4 3

1 2 x
L

Assume that its size is L = 1 and that shape functions can be represented as Ni =
a1 (a2 + x)(a3 + y).
2.3. For the square element of the previous problem, estimate the heat-generation
vector 
{rQ } = Q[N]T dV .
V

Use the shape functions obtained in the previous problem.

http://www.springer.com/978-1-84882-971-8