Vika Rizkia, ST., MT.

Mechanichal Engineering
Jakarta State Polythechnic
 The Metals Handbook defines hardness as
Resistance of metal to plastic deformation,
usually by indentation

The term may also refer to stiffness or temper, or to resistance to scratching, abrasion, or cutting. It
is the property of a metal, which gives it the ability to resist being permanently, deformed (bent,
broken, or have its shape changed), when a load is applied

In mineralogy the property of matter commonly described as the resistance of a substance to being
scratched by another substance

In metallurgy hardness is defined as the ability of a material to resist plastic

deformation

The greater the hardness of the metal, the greater resistance it has to
deformation

Materials with higher hardness have higher Tensile Strength and

Brittleness. Softer material are more ductile
Hardness measurement can be defined as macro-, micro- or nano-
scale according to the forces applied and displacements obtained

Measurement of the macro-hardness of materials is a quick and simple method of

obtaining mechanical property data for the bulk material from a small sample. It
is also widely used for the quality control of surface treatments processes

However, when concerned with coatings and surface properties of importance to

friction and wear processes for instance, the macro-indentation depth would be too
large relative to the surface-scale features

Where materials have a fine microstructure, are multi-phase, non-homogeneous or prone to

cracking, macro-hardness measurements will be highly variable and will not identify individual
surface features. It is here that micro-hardness measurements are appropriate.

Microhardness is the hardness of a material as determined by forcing an indenter such as a Vickers

or Knoop indenter into the surface of the material under 15 to 1000 gf load; usually, the
indentations are so small that they must be measured with a microscope.

Capable of determining hardness of different microconstituents within a structure, or measuring

steep hardness gradients such as those encountered in casehardening.
Hardness measurement can be defined as macro-, micro- or nano-
scale according to the forces applied and displacements obtained

Conversions from microhardness values to tensile strength and other hardness scales
(e.g. Rockwell) are available for many metals and alloys
Micro-indenters works by pressing a tip into a sample and continuously measuring:
applied load, penetration depth and cycle time

Nano-indentation tests measure hardness by indenting using very small, on the

order of 1 nano-Newton, indentation forces and measuring the depth of the
indention that was made. These tests are based on new technology that allows
precise measurement and control of the indenting forces and precise measurement
of the indentation depths

By measuring the depth of the indentation, progressive levels of forcing are measurable on the same
piece. This allows the tester to determine the maximum indentation load that is possible before the
hardness is compromised and the film is no longer within the testing ranges.
Scratch Hardness Testing

Indentation Hardness
Testing
Introduced by Friedrich Mohs in 1822
Mohs based the scale on ten minerals that are all
readily available
The hardest of material is measured against the scale
by finding the hardest material that the given material
can scratch, and / or the softest material that can
scratch the given material
Introduced by Friedrich Mohs in 1822
Mineral Hardness #
Diamond 10
Corundum 9
Topaz
8
Hard Cr plating 8 Mohs
Martensitic steel 7-8
Quartz 7 W7
scale
Feldspar 6
Apatite 5
Fluorite 4 Mild steel 3-4
Calcite 3 Copper 2-3
Gypsum 2 Lead 1-2
Talc 1
if a mineral is scratched by orthoclase but not by apatite, its Mohs hardness is between 5 and 6.
In the determination procedure it is necessary to be certain that a scratch is actually made and
not just a "chalk" mark that will rub off.

If the species being tested is fine-grained, friable, or pulverulent,

the test may only loosen grains without testing individual mineral
surfaces

Thus certain textures or aggregate forms may hinder or prevent a

true hardness determination
For this reason the Mohs test, while greatly facilitating the identification
of minerals in the field, is not suitable for accurately gauging the
hardness of industrial materials such as steel or ceramics

Another disadvantage of the Mohs scale is that it is not linear; that is, each increment of one in
the scale does not indicate a proportional increase in hardness
The progression from calcite to fluorite (from 3 to 4 on the Mohs scale) reflects an
increase in hardness of approximately 25 percent; the progression from corundum to
diamond, on the other hand (9 to 10 on the Mohs scale), reflects a hardness increase of
more than 300 percent
There are three types of tests used with accuracy by the metals industry; they are the
Brinell hardness test, the Rockwell hardness test, and the Vickers hardness test

The tests determine the depth which such a ball or cone will sink into the metal, under a
given load, within a specific period of time.

The followings are the most common hardness test methods used in today`s
technology :

- Rockwell hardness test

- Brinell hardness
- Vickers
- Knoop hardness
 is determined by forcing a hard steel or carbide sphere of a specified
diameter under a specified load into the surface of a material and
measuring the diameter of the indentation left after the test.

The Brinell hardness number, or simply the Brinell number, is

obtained by dividing the load used, in kilograms, by the actual
surface area of the indentation, in square millimeters

The Brinell hardness test uses a desk top machine to press a 10mm diameter, hardened steel ball into
the surface of the test specimens

The machine applies a load of 500 kilograms for soft metals such as copper, brass and thin stock. A
1500 kilogram load is used for aluminum castings, and a 3000 kilogram load is used for materials such
as iron and steel. The load is usually applied for 10 to 15 seconds.

After the impression is made, a measurement of the diameter of the resulting round impression is
taken. It is measured to plus or minus 0.05mm using a low-magnification portable microscope
 P
BHN
D / 2D D2 d 2
P load in kg
D diameter of the ball in mm
d diameter of indentation in mm
 A well structured Brinell hardness
number reveals the test conditions,
and looks like this,
"75 HB 10/500/30"

a Brinell Hardness of 75 was obtained

using a 10mm diameter hardened steel with
a 500 kilogram load applied for a period of
30 seconds

On tests of extremely hard metals a tungsten carbide ball is substituted for the steel ball.
Among the three hardness tests discussed, the Brinell ball makes the deepest and widest indentation,
so the test averages the hardness over a wider amount of material, which will more accurately account
for multiple grain structures, and any irregularities in the uniformity of the alloy.

The load applied in this test is usually 3,000, 1,500, or 500 kgf

The full test load is applied for 10 to 15 seconds

Two diameters of impression at right angles are measured

the mean diameter is used as a basis for calculating the Brinell hardness number (BHN)
1. Sample must be ten times thicker 1. Widely used and well accepted
than the indentation depth (sample 2. Large ball gives good average
usually should be at least 3/8" reading with a single test
thick).
3. Accurate
2. Test is most accurate if the
indentation depth is 2.5 - 5.0 mm. 4. Easy to learn and use
Adjust load to achieve this.
3. Test is no good if BHN > 650 Material P/D2 ~BHN
4. Sensitivity problem. Error due to
operator reading Brinell Microscope Steels and
30 Over 100
(10%max) cast iron
Copper and
10 30-200
Al alloys
Pure Al 5 15-100
Tin, lead and
1 3-20
their alloys
 It is the standard method for measuring the hardness of metals, particularly those
with extremely hard surfaces: the surface is subjected to a standard pressure for a
standard length of time by means of a pyramid-shaped diamond. The diagonal of
the resulting indention is measured under a microscope and the Vickers Hardness
value read from a conversion table

Vickers hardness is a measure of the hardness of a material,

calculated from the size of an impression produced under load by
a pyramid-shaped diamond indenter. Devised in the 1920s by
engineers at Vickers, Ltd., in the United Kingdom

The indenter employed in the Vickers test is a square-based pyramid whose opposite
sides meet at the apex at an angle of 136

The diamond is pressed into the surface of the material at loads ranging up to approximately 120
kilograms-force, and the size of the impression (usually no more than 0.5 mm) is measured with the aid
of a calibrated microscope
 1. The indenter is pressed into the
sample by an accurately controlled
test force.
2. The force is maintained for a specific
dwell time, normally 10 15 seconds.
3. After the dwell time is complete, the
indenter is removed leaving an indent
in the sample that appears square
shaped on the surface.
4. The size of the indent is determined
optically by measuring the two
diagonals of the square indent.

1. ASTM E384 = microvickers

2. ASTM E92 = vickers

HV = 1854.4 x P/d2
P load in kg
d diameter of indentation in mm
The Vickers test is reliable for measuring the hardness of metals, and also used on ceramic materials

The Vickers testing method is similar to the Brinell test. Rather than using the Brinell's steel ball
type indenter, and have to calculate the hemispherical area of impression, the Vickers machine uses
a penetrator that is square in shape, but tipped on one corner so it has the appearance of a playing
card "diamond".

The Vickers indenter is a 136 degrees square-based diamond cone, the diamond material of the
indenter has an advantage over other indenters because it does not deform over time and use.

The load varies from 1 to 120 kilograms.

To perform the Vickers test, the

specimen is placed on an anvil that has
a screw threaded base. The anvil is
turned raising it by the screw threads
until it is close to the point of the
indenter. With start lever activated, the
load is slowly applied to the indenter.
The load is released and the anvil with
the specimen is lowered. The operation
of applying and removing the load is
controlled automatically.
 Need to optically measure the One scale covers the entire hardness
indent size. This requires that range.
the test point be highly A wide range of test forces to suit
every application.
polished to be able to see the
Nondestructive, sample can
indent well enough to make an normally be used.
accurate measurement. The small diamond indenter and low
Slow. Testing can take 30 test forces allows testing very small
seconds not counting the parts or material features not
capable if being tested any other
sample preparation time. way
 a hardness measurement based on the net
increase in depth of impression as a load is
applied

Hardness numbers have no units and are commonly given in the R, L, M, E and K scales. The
higher the number in each of the scales means the harder the material.

The indenter may either be a steel ball of some specified diameter or a spherical diamond-
tipped cone of 120 angle and 0.2 mm tip radius, called Brale. The type of indenter and the test
load determine the hardness scale(A, B, C, etc)[4].

a hardness number is determined by

the difference in depth
of penetration resulting from the
application of an initial minor load
followed by a larger major load;
A minor load of 10 kg is first applied, which causes an initial penetration
and holds the indenter in place.

Then, the dial is set to zero and the major load is applied

Upon removal of the major load, the depth reading is taken while the minor
load is still on

The hardness number may then be read directly from the scale

The hardness testing of plastics is most commonly measured by the Rockwell

hardness test or Shore (Durometer) hardness test. Both methods measure the
resistance of the plastic toward indentation. Both scales provide an empirical
hardness value that doesn't correlate to other properties or fundamental
characteristics. Rockwell hardness is generally chosen for 'harder' plastics such as
nylon, polycarbonate, polystyrene, and acetal where the resiliency or creep of the
polymer is less likely to affect the results.

The Rockwell hardness test does not serve well as a predictor of other
properties such as strength or resistance to scratches, abrasion, or wear, and
should not be used alone for product design specifications
 Widely used and well accepted
Little operator subjectivity direct reading
Accurate
Fast
Large range of scales (plastics to steels)
Regular surface preparation (polishing not
needed)
the minor load is 10 kg

the minor load is 3 kg

 Scale Indenter Major Typical Applications of Scales
Symbol Load
kgf

HRA Brale 60 Cemented carbides, thin steel and shallow case hardened steel
Diamond

HRB 1/16" ball 100 Copper alloys, soft steels, aluminum alloys, malleable iron

HRC Brale 150 Steel, hard cast irons, pearlitic malleable iron, titanium, deep case hardened
Diamond steel and other materials harder than B100

HRD Brale 100 Thin steel and medium case hardened steel and pearlitic malleable iron
Diamond

HRE 1/16" ball 100 Cast iron, aluminum and magnesium alloys, bearing metals

HRF 1/16" ball 60 Annealed copper alloys, thin soft sheet metals

HRG 1/16" ball 150 Phosphor bronze, beryllium copper, malleable irons. Upper limit G92 to avoid
possible flattening of ball
HRH 1/8" ball 60 Aluminum, zinc, lead

HRK 1/8" ball 150

HRL 1/4" ball 60
HRM 1/4" ball 100 Bearing metals and other very soft or thin materials, including plastics (See
HRP 1/4" ball 150 ASTM D785). Use smallest ball and heaviest load that do not give anvil effect.
HRR 1/2" ball 60
HRS 1/2" ball 100
HRV 1/2" ball 150
Scale Symbol Indenter Major Typical Applications of Scales
Load
kg

HR15N Brale Diamond 15 kg Cemented carbides, thin steel and shallow

HR30N 30 kg case hardened steel
HR45N 45 kg Steel, hard cast irons, pearlitic malleable iron,
titanium, deep case hardened steel and other
materials harder than B100
Thin steel and medium case hardened steel
and pearlitic malleable iron
HR15T 1/16" ball 15 kg Copper alloys, soft steels, aluminum alloys,
HR30T 30 kg malleable iron
HR45T 45 kg Annealed copper alloys, thin soft sheet metals
Phosphor bronze, beryllium copper, malleable
irons. Upper limit G92 to avoid possible
flattening of ball
HR15W 1/8" ball 15 kg Cast iron, aluminum and magnesium alloys,
HR30W 30 kg bearing metals
HR45W 45 kg Aluminum, zinc, lead
Steel, hard cast irons, pearlitic malleable
HR15X 1/4" ball 15 kg
HR30X 30 kg
HR45X 45 kg
HR15Y 1/2" ball 15 kg
HR30Y 30 kg
HR45Y 45 kg
Whats Your Message?