This document contains 8 practice problems related to tensile testing of materials:
1. Calculating elongation of a copper specimen under tensile stress.
2-3. Determining maximum load and change in length for brass and steel specimens under tensile stress.
4. Calculating strain in an aluminum specimen under tensile force.
5. Calculating modulus of elasticity for a steel specimen under tensile load.
6. Calculating elongation of a titanium wire under tensile load.
7. Determining maximum load and length change without plastic deformation for a bronze alloy.
8. Determining diameter required for a copper rod to elongate a specified amount under tensile load
This document contains 8 practice problems related to tensile testing of materials:
1. Calculating elongation of a copper specimen under tensile stress.
2-3. Determining maximum load and change in length for brass and steel specimens under tensile stress.
4. Calculating strain in an aluminum specimen under tensile force.
5. Calculating modulus of elasticity for a steel specimen under tensile load.
6. Calculating elongation of a titanium wire under tensile load.
7. Determining maximum load and length change without plastic deformation for a bronze alloy.
8. Determining diameter required for a copper rod to elongate a specified amount under tensile load
This document contains 8 practice problems related to tensile testing of materials:
1. Calculating elongation of a copper specimen under tensile stress.
2-3. Determining maximum load and change in length for brass and steel specimens under tensile stress.
4. Calculating strain in an aluminum specimen under tensile force.
5. Calculating modulus of elasticity for a steel specimen under tensile load.
6. Calculating elongation of a titanium wire under tensile load.
7. Determining maximum load and length change without plastic deformation for a bronze alloy.
8. Determining diameter required for a copper rod to elongate a specified amount under tensile load
This document contains 8 practice problems related to tensile testing of materials:
1. Calculating elongation of a copper specimen under tensile stress.
2-3. Determining maximum load and change in length for brass and steel specimens under tensile stress.
4. Calculating strain in an aluminum specimen under tensile force.
5. Calculating modulus of elasticity for a steel specimen under tensile load.
6. Calculating elongation of a titanium wire under tensile load.
7. Determining maximum load and length change without plastic deformation for a bronze alloy.
8. Determining diameter required for a copper rod to elongate a specified amount under tensile load
A. Pengujian Tarik 1. A piece of copper originally 305 mm (12 in.) long is pulled in tension with a stress of 276 MPa (40,000 psi). If the deformation is entirely elastic, what will be the resultant elongation? E=110 GPa
2.
From the tensile stressstrain behavior for the brass specimen shown in Figure 7.12, determine the following: a. The maximum load that can be sustained by a cylindrical specimen having an original diameter of 12.8 mm (0.505 in.). b. The change in length of a specimen originally 250 mm (10 in.) long that is subjected to a tensile stress of 345 MPa (50,000 psi) and E = 97 GPa.
3. A cylindrical specimen of steel having an original diameter of 12.8 mm (0.505 in.) is
tensile tested to fracture and found to have an engineering fracture strength _f of 460 MPa (67,000 psi). If its cross-sectional diameter at fracture is 10.7 mm (0.422 in.), determine: a. The ductility in terms of percent reduction in area. b. The true stress at fracture.
4. A specimen of aluminum having a rectangular cross section 10 mm x 12.7 mm (0.4
in.x 0.5 in.) is pulled in tension with 35,500 N (8000 lbf ) force, producing only elastic deformation. Calculate the resulting strain. (E aluminum = 69 GPa)
5. A steel bar 100 mm (4.0 in.) long and width 20 mm (0.8 in.) on an edge is pulled in tension with a load of 89,000 N (20,000 lbf ), and experiences an elongation of 0.10 mm. Assuming that the deformation is entirely elastic, calculate the elastic modulus of the steel.
6. Consider a cylindrical titanium wire 3.0 mm (0.12 in.) in diameter and
2.5x104mm(1000 in.) long. Calculate its elongation when a load of 500 N (112 lbf ) is applied. Assume that the deformation is totally elastic (E titanium = 107 GPa)
7. For a bronze alloy, the stress at which plastic deformation begins is 275 MPa (40,000 psi), and the modulus of elasticity is 115 GPa. a. What is the maximum load that may be applied to a specimen with a cross- sectional area of 325mm2 without plastic deformation? b. If the original specimen length is 115 mm (4.5 in.), what is the maximum length to which it may be stretched without causing plastic deformation? 8. A cylindrical rod of copper (E =110 GPa) having a yield strength of 240 MPa (35,000 psi) is to be subjected to a load of 6660 N (1500 lbf ). If the length of the rod is 380 mm (15.0 in.), what must be the diameter to allow an elongation of 0.50 mm (0.020 in.)?
