INSTALLATION

G OVERNORS

A
Magnetic Speed Pickups
Magnetic Speed Pickup Installattion: MERICA
1. If no mounting loacation is available, then drill and tap a hole in the flywheel hous-
ing. The threaded hole should be perpendicular to the center line of the crankshaft
and centered over the ring gear teeth. Spot face the hole to provide a flat surface
on which to anchor the locknut. (Refer to the charts on the inner page for the thread
C ORP.
MSP Series

size of the Magnetic Speed Pickup)

GACs Magnetic Speed Sensors are a rugged and economic
2. Insert the magnetic speed pickup into the hole and turn it until the magnetic speed
solution for detecting engine speed. Sturdier than plastic
pickup makes contact with the face of the gear.
sensors and outperforming semiconductor-type devices at
3. Back out the magnetic pickup by turning it counter clockwise. (About a 3/4 turn) high temperatures, GACs epoxy encapsulated sensors are
The gap between the pickup and gear should be no smaller than 0.025 in (0.64 mm) unaffected by dust and dirt. Multiple sizes and customizable
and 0.035 in (0.89 mm) configurations are available.

3/4 Turn
4. Wire leads should be twisted for their entire length from
the magnetic speed sensor to the control unit. Shielding is FEATURES
required if external interference is present or the leads are
longer than 10 ft ( 3 m).
Produces Electrical Frequency -65F to +225F (-55C to +105C)
Operating Temperature
0.025 in (0.64 mm) 0.035 in (0.89 mm) Requires No Energizing Circuit From Control
minimum gap maximum gap Available For Hazardous Location Installation
Used On All GACs Electronic Speed Controllers (Not Certified)

OPTIONS SPECIFICATIONS
TSE050 Power Input
A New Tool For Your Toolkit! Dimensions See Chart on Inside Pages
Proximity to Gear Teeth 0.025 - 0.035 in. (0.64 - 0.89 mm)
The TSE050 simulates a running engine when connected to Temperature Range -65 F to +225 F (-55 C to +105 C)
Output 0.5 - 30 Volts RMS Is Recommended For Input To Control Units
the magnetic pickup input on a speed control. An on-board
(1 V RMS When Cranking Engine)
potentiometer allows the signal to be adjusted between 750 Resistance (Varies From Sensor to Sensor) 160 - 1200 ohms
to 10,000 Hz and is compatible with all GAC speed controls
using a magnetic pickup.
CONNECTORS

Contact Your Local Dealer:

Governors America Corp.

720 Silver Street Agawam, MA 01001
Phone: 413.786.5600 Fax: 413.789.7736
www.governors-america.com Automotive Military Packard Dual Packard Stud Terminals
8.13 PTI3000 A
[email protected] 2013 Governors America Corp. All rights reserved.
 SELECTION CHART

5/8 - 18 UNF Threaded BODY THREAD CABLE CONNECTOR DRILL 3/8 - 24 UNF-2A Threaded BODY
THREAD CABLE CONNECTOR DRILL
LENGTH LENGTH LENGTH TYPE SIZE LENGTH LENGTH TYPE SIZE

3 Without Mating Half 3.125 2.75 2.50 2.5 With 6 Shielded 2.7 2.25 72.00
MSP674 WIRE LEADS 37/64 MSP6729 (69) (57) (1829) WIRE LEADS 0.332
Connector / High Output (79) (70) (64) Cable

3.125 2.75 7.00 1.5 With 6 Shielded 1.7 1.25 72.00

MSP675 3 With 7 Leads WIRE LEADS 37/64 MSP6730 (43) (32) (1829) WIRE LEADS 0.332
(79) (70) (178) Cable

5.0 4.625 12.00 4.0 With 6 Shielded 4.0 3.55 72.00

MSP676 5 With 12 Leads WIRE LEADS 37/64 MSP6731 (102) (90) (1829) WIRE LEADS 0.332
(127) (118) (305) Cable

3 Without Mating Half 3.125 2.75 1.7 With 6 Shielded 1.7 1.25 72.00
MSP677 (79) (70) n/a MILITARY 37/64 MSP6740 PACKARD 0.332
Connector Cable (43) (32) (1829)

5 Without Mating Half 5.00 4.75

MSP678 (127) (121) n/a MILITARY 37/64
Connector

3 Mating Half Connector 3.125 2.75

MSP679 (79) (70) n/a MILITARY 37/64
/ Weather Boot
3/4 - 16 UNF Threaded BODY THREAD CABLE CONNECTOR
TYPE
DRILL
LENGTH LENGTH LENGTH SIZE
5 Mating Half Connector 5.00 4.75
MSP6710 (127) (121) n/a MILITARY 37/64
/ Weather Boot 4.00 3.375 2.50
MSP6724 3.5 With 3 Leads (102) (86) (64) AUTOMOTIVE 11/16

MSP6719 2.375 With 12 Leads 2.375 2.00 6.00 WIRE LEADS 37/64
(60) (51) (152) 3.5 With 3 Leads / With
MSP6724C 4.00 3.375 2.50 AUTOMOTIVE 11/16
Mating Half Connector (102) (86) (64)
MSP6720 4 With 6 Leads 3.875 3.50 4.500 WIRE LEADS 37/64
(98) (59) (114)
3.5 With 4 Leads 4.00 3.375
MSP6734 (102) (86) 4.25 WIRE LEADS 11/16
MSP6721 3 With 3 Leads 3.125 2.75 2.50 AUTOMOTIVE 37/64
(79) (70) (64)
4.00 3.375 2.50
3 With 3 Leads / Mating MSP6735 3.5 With 3 Leads (102) (86) PACKARD 11/16
MSP6721C 3.125 2.75 2.50 AUTOMOTIVE 37/64 (64)
Half Connector (79) (70) (64)

3.125 2.75 6.5 MSP6744 2.29 With 8/32 Stud Term 3.50 2.29 n/a STUD 11/16
MSP6728 3 With 10 Leads (79) (70) (165) PACKARD 37/64 (90) (58)

3 With 10 Leads / Mat-

MSP6728C ing Half Connector 3.125 2.75 6.5 PACKARD 37/64
(79) (70) (165)

3 With 4 Leads / Dual 3.125 2.75 3.0

MSP6732 (79) (70) (76) DUAL PACKARD 37/64
Output
M16 x 1.5 Threaded BODY THREAD CABLE CONNECTOR DRILL
3 With 4 Leads / Dual LENGTH LENGTH LENGTH TYPE SIZE
MSP6732C Output / Mating Half 3.125 2.75 3.0 DUAL PACKARD 37/64
(79) (70) (76) 3 Without Mating Half 3.125 2.875
Connector MSP6714 n/a MILITARY 14mm
Connector (79) (73)
3.75 With 8/32 Stud 4.38 3.55
MSP6743 (111) (90) n/a STUD 37/64
Terminals 3 With Mating Half Con- 3.125 2.875
MSP6715 (79) (73) n/a MILITARY 14mm
nector / Weather Boot

MSP6723 3 With 3 Leads 3.125 2.75 2.50 AUTOMOTIVE 14mm

(79) (70) (64)

M18 x 1.5 Threaded BODY THREAD CABLE CONNECTOR DRILL

MSP6723C
3 With 3 Leads / With 3.125 2.75 2.50 AUTOMOTIVE 14mm
LENGTH LENGTH LENGTH TYPE SIZE Mating Half Connector (79) (70) (64)

3.20 2.30 9.0

MSP6741 3.25 With 9 Leads PACKARD 21/32
(81) (58) (229)
NOTE: For the most up-to-date list of magnetic speed pickups, go to governors-america.com. GAC is continuously adding new solutions
for engine speed sensing.