ZNV

For Internal Use Only
ZNV Client User Manual

(Android)
SHENZHEN ZNV TECHNOLOGY CO., LTD.
<All information contained in this document is for the internal use of ZNV. No spreading without permission.> 1
Contents
1 Device Connection ......................................................................................... 3
2 APP Installation Configuration ...................................................................... 5
3 APP Use ........................................................................................................ 11
1 Device Connection
This is to connect a camera to a home LAN (local area network). Two ways of connection
are available: one is WPS (Wi-Fi Protected Setup), and the other is wired connection.
After connection, the mobile phone accesses the same router via wireless connection for
operations such as search, adding, configuration, and browsing.
1. WPS
Press the WPS button on the router and network card within two minutes. If the
router does not have the WPS button, you have to choose wired connection.
Figure 1-1 Wireless Connection
2. Wired connection
Connect the IP camera to a special power supply attached, and connect the IP
camera to the router with a network cable.
Figure 1-2 Wired Connection
2 APP Installation Configuration

1. Download the ZNV.apk application from the ZNV website and install it.
Figure 2-1 Downloading the APP
2. Open the installed application, register a local account, and log in to the device with
the registered user name.
Figure 2-2 Registration
Figure 2-3 Login
3. Enter the application, and click a camera icon in the interface to go to the interface
for adding a camera.
Figure 2-4 Camera Icon
4. Add a camera in three ways on the page for adding a camera: scan, searchUID,
and entering the UID manually.
Figure 2-5 Adding a Camera
i. Scan
Click the scan button and scan the QR (Quick Response) code on the camera
with the mobile camera module to automatically enter the camera ID.
Figure 2-6 QR Code Scanning
ii. Search UID
When the camera and the mobile phone are connected with the same router,
click the searchUID button to search all devices within the LAN. Click any of
the listed search result (UID and IP address) to add the desired device.
Figure 2-7 Searching the UID
iii. Entering the UID manually
Figure 2-8 Entering the UID manually
5. After entering the UID, type the password (admin by default) and camera name,
and click the Save button on the upper right corner to complete adding the camera.
Figure 2-9 Entering the Password and Camera Name
3 APP Use
1. With the camera added, you can see the camera list and screen in the APP main
interface.
Figure 3-1 Camera List and Screen
2. Click the screen to view the monitoring image and gesture to move the PTZ and
zoom the camera.
Figure 3-2 Gesturing
3. In a vertical screen, the status bar displays the Back button, the list of devices of the
same IP address, and the fresh and setting buttons. The resolution, number of
online users and network status are shown above the image. Operations such as
replay, muting/listening, talk, snapshot, and album are available below the image.
Figure 3-3 Vertical Screen
i. Device list
When a DVR (Digital Video Recorder) or NVR (Network Video Recorder) is

accessed, click the device list on the status bar to switch between cameras of
different channels under the same device.
Figure 3-4 Device List
ii. Replay
Click the replay button to go to the Replay interface, where you can filter
events within an hour, within half a day, within a day, within a week, or in a
custom period.
Figure 3-5 Replay
Click a searched event listed in the figure below to view an associated record.
Figure 3-6 Searched Events
iii. Mute/Listen
Click to switch between the mute status and the listening status. You can
only view a record in the mute status, and view a record and listen to the talk
simultaneously in the listening status.
Figure 3-7 Muting/Listening
iv. Talk
Hold the talk button to enable talk between the mobile phone and the
device.
Figure 3-8 Talk
v. Snapshot
Click the snapshot button to take a snapshot of the current image. The
system saves snapshot to the album automatically.
Figure 3-9 Snapshot
vi. View pictures
Click to go to the album and view taken pictures.
Figure 3-10 Album
Click a picture to view its full image, and click the Share button to share the
picture to Sina Weibo or WeChat Moments.
Figure 3-11 Sharing a Picture
4. Camera Setting: In a monitoring image, click the setting button on the upper
right corner to go to the Camera Setting interface.
Figure 3-12 Camera Setting
i. Name
Modify a camera name.
Figure 3-13 Name
ii. Record Setting
You can choose among Close, All Time, and Alert modes under Record
Setting.
Figure 3-14 Record Setting
iii. Video Setting
Video Setting: You can choose among Low, Middle, and High modes under
Video Quality, and Normal, Vertical Flip, Horizontal Flip, Vertical and
Horizontal Flip modes under Image Flip.
Figure 3-15 Video Setting
Figure 3-16 Video Quality and Image Flip
iv. Event Setting
Event Setting: You can modify sensitivity (Close, Low, Middle, and High) of
motion detection. Event Reminder: You can choose among the Silent, Ring,
Vibrate, Ring and Vibrate types.
Figure 3-17 Event Setting
Figure 3-18 Motion Detection and Event Reminder
v. WiFi Management
Reset WiFi connection at the device side.
Figure 3-19 WiFi Management
vi. Change Password
Change the password of the camera.
Figure 3-20 Change Password
vii. Device Information
View the model, version, and manufacturer of the camera.
viii. Clear Cache
Format the T-flash card on the camera.
Figure 3-21 Formatting
ix. Delete Camera
Delete the camera associated with the APP.
Figure 3-22 Delete Camera
5. More: Click the More button in the main interface of the APP client to go to the
interface for more setting, for example, traffic statistics, message and position
setting, and feedback.
Figure 3-23 More

ZNV

Uploaded by

Copyright:

Available Formats

ZNV

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ZNV

Uploaded by

Copyright:

Available Formats

For Internal Use Only

ZNV Client User Manual

SHENZHEN ZNV TECHNOLOGY CO., LTD.

2 APP Installation Configuration ...................................................................... 5

3 APP Use ........................................................................................................ 11

Figure 1-1 Wireless Connection

Figure 1-2 Wired Connection

2 APP Installation Configuration

Figure 2-1 Downloading the APP

Figure 2-2 Registration

Figure 2-3 Login

Figure 2-4 Camera Icon

Figure 2-5 Adding a Camera

Figure 2-6 QR Code Scanning

ii. Search UID

Figure 2-7 Searching the UID

iii. Entering the UID manually

Figure 2-8 Entering the UID manually

Figure 2-9 Entering the Password and Camera Name

Figure 3-1 Camera List and Screen

Figure 3-2 Gesturing

Figure 3-3 Vertical Screen

When a DVR (Digital Video Recorder) or NVR (Network Video Recorder) is

Figure 3-4 Device List

Figure 3-5 Replay

Figure 3-6 Searched Events

Figure 3-7 Muting/Listening

Figure 3-8 Talk

Figure 3-9 Snapshot

vi. View pictures

Click to go to the album and view taken pictures.

Figure 3-10 Album

Figure 3-11 Sharing a Picture

Figure 3-12 Camera Setting

Modify a camera name.

Figure 3-13 Name

ii. Record Setting

Figure 3-14 Record Setting

iii. Video Setting

Figure 3-15 Video Setting

Figure 3-16 Video Quality and Image Flip

iv. Event Setting

Figure 3-17 Event Setting

Figure 3-18 Motion Detection and Event Reminder

Reset WiFi connection at the device side.

Figure 3-19 WiFi Management

vi. Change Password

Change the password of the camera.

Figure 3-20 Change Password

vii. Device Information

View the model, version, and manufacturer of the camera.

viii. Clear Cache

Format the T-flash card on the camera.

Figure 3-21 Formatting

ix. Delete Camera

Delete the camera associated with the APP.

Figure 3-22 Delete Camera

Figure 3-23 More

You might also like