Chapter 2

Transformer: Principles and Practices

2.1 Introduction

There are many devices such as three-phase ac generator, transformer etc., which
are usually used in a power station to generate and supply electrical power to a
power system network. In the power station, the three-phase ac generator generates
a three-phase alternating voltage in the range between 11 and 20 kV. The magni-
tude of the generated voltage is increased to 120 kV or more by means of a power
transformer. This higher magnitude of voltage is then transmitted to the grid sub-
station by a three-phase transmission lines. A lower line voltage of 415 V is
achieved by stepping down either from the 11 or 33 kV lines by a distribution
transformer. In these cases, a three-phase transformer is used in either to step-up or
step-down the voltage. Since a transformer plays a vital role in feeding an electrical
network with the required voltage, it becomes an important requirement of a power
system engineer to understand the fundamental details about a transformer along
with its analytical behavior in the circuit domain. This chapter is dedicated towards
this goal. On the onset of this discussion it is worth mentioning that a transformer,
irrespective of its type, contains the following characteristics (i) it has no moving
parts, (ii) no electrical connection between the primary and secondary windings,
(iii) windings are magnetically coupled, (iv) rugged and durable in construction,
(v) efciency is very high i.e., more than 95 %, and (vi) frequency is unchanged.

2.2 Working Principle of Transformer

Figure 2.1 shows a schematic diagram of a single-phase transformer. There are two
types of windings in a single-phase transformer. These are called primary and
secondary windings or coils. The primary winding is connected to the alternating

Springer Science+Business Media Singapore 2016 49

Md.A. Salam and Q.M. Rahman, Power Systems Grounding,
Power Systems, DOI 10.1007/978-981-10-0446-9_2
50 2 Transformer: Principles and Practices

Fig. 2.1 Single-phase transformer

voltage source and the secondary winding is connected to the load. The primary and
secondary winding parameters are represented by the sufx p or 1 and s or 2,
respectively. A sinusoidal current flows in the primary winding when it is con-
nected to an alternating voltage source. This current establish a flux u which moves
from the primary winding to the secondary winding through low reluctance mag-
netic core.
About 95 % of this flux moves from the primary to the secondary through the
low reluctance path of the magnetic core and this flux is linked by the both
windings and a small percent of this flux links to the primary winding. According to
the Faradays laws of electromagnetic induction, a voltage will be induced across the
secondary winding as well as in the primary winding. Due to this voltage, a current
will flow through the load if it is connected with the secondary winding. Hence, the
primary voltage is transferred to the secondary winding without a change in
frequency.

2.3 Flux in a Transformer

The current in the primary winding establishes a flux. The flux that moves from
primary to secondary and links both the windings is called the mutual flux and its
maximum value is represented by /m .
Flux which links only the primary winding and completes the magnetic path
through the surrounding air is known primary leakage flux. The primary leakage
flux is denoted by /1l . Similarly, secondary leakage flux is that flux which links
only the secondary winding and completes the magnetic path through the sur-
rounding air. The secondary leakage flux is denoted by /2l . Mutual and leakage
fluxes are shown in Fig. 2.2.
2.4 Ideal Transformer 51

m I2
I1
+ N2 +
N1 E2
V1 V2 ZL
E1

2l
1l

Fig. 2.2 Mutual and leakage fluxes

2.4 Ideal Transformer

An ideal transformer is one which does not supply any energy to the load i.e., the
secondary winding is open circuited. The main points of an ideal transformer are
(i) no winding resistance, (ii) no leakage flux and leakage inductance,
(iii) self-inductance and mutual inductance are zero, (iv) no losses due to resistance,
inductance, hysteresis or eddy current and (v) coefcient of coupling is unity.
Figure 2.3a shows an ideal transformer where the secondary winding is left
open. A small magnetizing current Im will flow in the primary winding when it is
connected to the alternating voltage source, V1 . This magnetizing current lags
behind the supply voltage, V1 by 90 and produces the flux u, which induces the
primary and secondary emfs. These emfs lag behind the flux, u by 90. The
magnitude of primary induced emf E1 and supply voltage V1 is the same, but are
180 out of phase as shown in Fig. 2.3b.

(a) m
I1
+ +
V1 E1 E2 N2 V2
N1

(b) V2
V1
E2 E1 90
I m = I1

Fig. 2.3 Ideal transformer and phasor diagram

52 2 Transformer: Principles and Practices

2.5 E.M.F. Equation of Transformer

The primary winding draws a current when it is connected to an alternating voltage

source. This primary sinusoidal current produces a sinusoidal flux u that can be
expressed as,

/ /m sin xt 2:1

Instantaneous emf induced in the primary winding is,

d/
e1 N1 2:2
dt

Similarly, instantaneous emf induced in the secondary winding is,

d/
e2 N2 2:3
dt

Substituting Eq. (2.1) into the Eq. (2.2) yields,

d
e1 N1 / sin xt 2:4
dt m
e1 N1 x/m cos xt 2:5

e1 N1 x/m sinxt  90 2:6

The maximum value of e1 is,

Em1 N1 x/m 2:7

The rms value of the primary emf is,

Em1
E1 p 2:8
2

Substituting Eq. (2.7) into Eq. (2.8) yields,

N1 2pf /m
E1 p 2:9
2

E1 4:44 f /m N1 2:10
2.5 E.M.F. Equation of Transformer 53

Similarly, the expression of the secondary emf is,

E2 4:44 f /m N2 2:11

The primary and secondary voltages can be determined from Eqs. (2.10) and (2.11)
if other parameters are known.

2.6 Turns Ratio of Transformer

Turns ratio is an important parameter for drawing an equivalent circuit of a

transformer. The turns ratio is used to identify the step-up and step-down trans-
formers. According to Faradays laws, the induced emf in the primary e1 and the
secondary e2 windings are,
d/
e1 N1 2:12
dt
d/
e2 N2 2:13
dt

Dividing Eq. (2.12) by Eq. (2.13) yields,

e1 N 1
2:14
e2 N 2
e1 N1
a 2:15
e2 N2

Similarly, dividing Eq. (2.10) by (2.11) yields,

E1 N1
a 2:16
E2 N2

where a is the turns ratio of a transformer. In case of N2 [ N1 , the transformer is

called a step-up transformer. Whereas for N1 [ N2 , the transformer is called a
step-down transformer. The losses are zero in an ideal transformer. In this case, the
input power of the transformer is equal to its output power and this yields,
V1 I1 V2 I2 2:17

Equation (2.17) can be rearranged as,

V1 I2
a 2:18
V2 I1
54 2 Transformer: Principles and Practices

The ratio of primary current to the secondary current is,

I1 1
2:19
I2 a

Again, the magnetomotive force produced by the primary current will be equal to
the magnetomotive force produced by the secondary current and it can be expressed
as,

= =1  =2 0 2:20

N1 I1 N2 I2 2:21

I1 N2 1
2:22
I2 N1 a

From Eq. (2.22), it is concluded that the ratio of primary to secondary current is
inversely proportional to the turns ratio of the transformer.
The input and output power of an ideal transformer is,

Pin V1 I1 cos /1 2:23

Pout V2 I2 cos /2 2:24

For an ideal condition, the angle /1 is equal to the angle /2 and the output power
can be re-arranged as,

V1
Pout aI1 cos /1 2:25
a
Pout V1 I1 cos /1 Pin 2:26

From Eq. (2.26), it is seen that the input and the output power are the same in case
of an ideal transformer. Similarly, the input and output reactive powers are,

Qout V2 I2 sin /2 V1 I1 sin /1 Qin 2:27

From Eqs. (2.26) and (2.27), the input and output power and reactive power can be
calculated if other parameters are given.
Example 2.1 The number of turns in the secondary coil of a 22 kVA, 2200 V/220 V
single-phase transformer is 50. Find the (i) number of primary turns, (ii) primary
full load current, and (iii) secondary full load current. Neglect all kinds of losses in
the transformer.
2.6 Turns Ratio of Transformer 55

Solution
The value of the turns ratio is,

V1 2200
a 10
V2 220

(i) The value of the primary turns can be determined as,

N1
a
N2
N1 aN2 10  50 500

(ii) The value of the primary full load current is,

22  103
I1 10 A
2200

(iii) The value of the secondary full load current is,

22  103
I2 100 A
220

Example 2.2 A 25 kVA single-phase transformer has the primary and secondary
number of turns of 200 and 400, respectively. The transformer is connected to a
220 V, 50 Hz source. Calculate the (i) turns ratio, and (ii) mutual flux in the core.
Solution

(i) The turns ratio is,

N1 200
a 0:5
N2 400

(ii) The value of the mutual flux can be calculated as,

V1 E1 4:44 f /m N1
V1 220
/m 4:95 mWb
4:44 fN1 4:44  50  200

Practice problem 2.1

The primary voltage of an iron core single-phase transformer is 220 V. The number
of primary and secondary turns of the transformer are 200 and 50, respectively.
Calculate the voltage of the secondary coil.
56 2 Transformer: Principles and Practices

Practice problem 2.2

The number of primary turns of a 30 kVA, 2200/220 V, 50 Hz single-phase
transformer is 100. Find the (i) turns ratio, (ii) mutual flux in the core, and (iii) full
load primary and secondary currents.

2.7 Rules for Referring Impedance

For developing equivalent circuit of a transformer, it is necessary to refer the

parameters from the primary to the secondary or the secondary to the primary.
These parameters are resistance, reactance, impedance, current and voltage. The
ratio of primary voltage to secondary voltage is [14],
V1
a 2:28
V2

The ratio of primary current to secondary current is,

I1 1
2:29
I2 a

Dividing Eq. (2.28) by Eq. (2.29) yields,

V1
V2 a
I1 1
2:30
I2 a

V1
I1
V2 a2 2:31
I2

Z1
a2 2:32
Z2

Alternative approach: The impedances in the primary and secondary windings are,
V1
Z1 2:33
I1
V2
Z2 2:34
I2

Dividing Eq. (2.33) by Eq. (2.34) yields,

V
Z1 I11
2:35
Z2 VI 2
2
2.7 Rules for Referring Impedance 57

Z1 V1 I2
 2:36
Z2 V2 I1
Z1
aa 2:37
Z2
Z1
a2 2:38
Z2

From Eq. (2.38), it can be concluded that the impedance ratio is equal to the square
of the turns ratio. The important points for transferring parameters are (i) R1 in the
primary becomes Ra21 when referred to the secondary, (ii) R2 in the secondary
becomes a2 R2 when referred to the primary, (iii) X1 in the primary becomes Xa21 when
referred to the secondary, and (iv) X2 in the secondary becomes a2 X2 when referred
to the primary.
Example 2.3 The number of primary and secondary turns of a single-phase
transformer are 300 and 30, respectively. The secondary coil is connected with a
load impedance of 4 X. Calculate the (i) turns ratio, (ii) load impedance referred to
the primary, and (iii) primary current if the primary coil voltage is 220 V.
Solution

(i) The value of the turns ratio is,

N1 300
a 10
N2 30

(ii) The value of the load impedance referred to primary is,

ZL0 a2 ZL 102  4 400 X

(iii) The value of the primary current is,

V1 220
I1 0:55 A
ZL0 400

Practice problem 2.3

A load impedance of 8 X is connected to the secondary coil of a 400/200 turns
single-phase transformer. Determine the (i) turns ratio, (ii) load impedance referred
to primary and (iii) primary current if the primary coil voltage is 120 V.
58 2 Transformer: Principles and Practices

2.8 Equivalent Circuit of a Transformer

Windings of a transformer are not connected electrically. The windings are mag-
netically coupled with each other. In this case, it is tedious to do proper analysis.
Therefore, for easy computation and visualization, the practical transformer needs
to be converted into an equivalent circuit by maintaining same properties of the
main transformer. In the equivalent circuit, the related parameters need to be
transferred either from the primary to the secondary or vice versa. A two windings
ideal transformer is shown in Fig. 2.4.

2.8.1 Exact Equivalent Circuit

Figure 2.5 shows an exact equivalent circuit referred to the primary where all the
parameters are transferred from the secondary to the primary and these parameters
are,

I1 R1 X1 R2 X2 I2

I0 N1 N2

+
Iw +
Im V2 ZL
V1 R0 X0 E2
E1

Fig. 2.4 Two windings transformer

I1 R1 X1 R2 ' X2 ' I2 '

I0

+
Iw +
Im V2 ' ZL '
V1 R0 X0

Fig. 2.5 Exact equivalent circuit referred to primary

2.8 Equivalent Circuit of a Transformer 59

R02 a2 R2 2:39

X20 a2 X2 2:40

ZL0 a2 ZL 2:41

I2
I20 2:42
a

V20 aV2 2:43

Figure 2.6 shows the exact equivalent circuit referred to the secondary where all the
parameters are transferred from the primary to the secondary.
These parameters are,

R1
R01 2:44
a2
X1
X10 2:45
a2

I10 aI1 2:46

V1
V10 2:47
a

Iw0 aIw 2:48

Im0 aIm 2:49

I00 aI0 2:50

I1 ' R1 ' X1 ' R2 X2 I2

I0 '

+
Iw ' +
Im ' V2 ZL
V1 ' R0 ' X0 '

Fig. 2.6 Exact equivalent circuit referred to secondary

60 2 Transformer: Principles and Practices

2.8.2 Approximate Equivalent Circuit

The no-load current is very small as compared to the rated primary current.
Therefore, there is a negligible voltage drop due to R1 and X1 . In this condition, it
can be assumed that the voltage drop across the no-load circuit is the same as the
applied voltage without any signicant error. The approximate equivalent circuit
can be drawn by shifting the no-load circuit across the supply voltage, V1 .
Figure 2.7 shows an approximate equivalent circuit referred to the primary. The
total resistance, reactance and impedance referred to the primary are,

R01 R1 R02 R1 a2 R2 2:51

X01 X1 X20 X1 a2 X2 2:52

Z01 R01 jX01 2:53

The no-load circuit resistance and reactance are,

V1
R0 2:54
Iw

V1
X0 2:55
Im

Figure 2.8 shows an approximate equivalent circuit referred to the secondary.

The total resistance, reactance and impedance referred to the secondary is,

R1
R02 R2 R01 R2 2:56
a2

I1 I2 ' R01 X 01

I0

+
Iw +
Im V2 ' ZL '
V1 R0 X0

Fig. 2.7 Approximate equivalent circuit referred to primary

2.8 Equivalent Circuit of a Transformer 61

I1 ' I2 R02 X 02

I0 '

+
Iw ' +
Im ' V2 ZL
V1 ' R0 ' X0 '

Fig. 2.8 Approximate equivalent circuit referred to secondary

X1
X02 X2 X10 X2 2:57
a2
Z02 R02 jX02 2:58

The no-load circuit resistance and reactance referred to the secondary are,
V10
R00 2:59
Iw0

V10
X00 2:60
Im0

Example 2.4 A 2.5 kVA, 200 V/40 V single-phase transformer has the primary
resistance and reactance of 3 and 12 , respectively. On the secondary side, these
values are 0.3 and 0.1 , respectively. Find the equivalent impedance referred to
the primary and the secondary.
Solution
The value of the turns ratio is,
V1 200
a 5
V2 40

The total resistance, reactance and impedance referred to the primary can be
determined as,

R01 R1 a2 R2 3 25  0:3 10:5 X

X01 X1 a2 X2 12 25  0:1 14:5 X
p
Z01 10:52 14:52 17:9 X
62 2 Transformer: Principles and Practices

The total resistance, reactance and impedance referred to the secondary are cal-
culated as,

R1 3
R02 R2 0:3 0:42 X
a2 25
X1 12
X02 X2 2 0:1 0:58 X
p 25
a
Z01 0:422 0:582 0:72 X

Practice problem 2.4

A 1.5 kVA, 220/110 V single-phase transformer has the primary resistance and
reactance of 6 and 18 , respectively. The resistance and reactance at the secondary
side are 0.6 and 0.5 , respectively. Calculate the equivalent impedance referred to
the primary and the secondary.

2.9 Polarity of a Transformer

The relative directions of induced voltages between the high voltage and low
voltage terminals is known as the polarity of a transformer. The polarity of a
transformer is very important to construct three-phase transformer bank, parallel
connection of transformer, connection of current transformer (CT) and potential
transformer (PT) power with metering device. Two polarities namely additive and
subtractive are used in the transformer.
A polarity of a transformer is said to be an additive if the measured voltage
between the high voltage and the low voltage terminals is greater than the supply
voltage at the high voltage terminals. The additive polarity of a transformer is
marked by the orientation of dots as shown in Fig. 2.9. Whereas, a polarity is said to
be a subtractive if the measured voltage between the high voltage and the low
voltage terminals is lower than the supply voltage at the high voltage terminals. The

Fig. 2.9 Additive polarity

H1
X1
VH1 H 2

H2
X2
2.9 Polarity of a Transformer 63

Fig. 2.10 Subtractive

polarity

H1
X1
VH1H 2

H2
X2

subtractive polarity of a transformer is marked by the orientation of dots as shown

in Fig. 2.10. Consider a 220/110 V single-phase transformer with the high voltage
and the low voltage terminals for testing polarities. The high voltage terminal H1 is
connected to the low voltage terminal X1 by a cable. The voltmeter is connected
between H2 and X2. In this case, the turns ratio of the transformer is,

V1 220
a 2
V2 110

For safety issue, a lower voltage needs to be applied to the primary side i.e., high
voltage terminals. Suppose, a voltage of 110 V is applied to the primary side. In this
case, a voltage of 55 V (110/2) will appear at the secondary terminals. If the meter
read out the voltage of 165 V (110 + 55) then the transformer is said to be in
additive polarity. This connection is shown in Fig. 2.11.
Whereas, if the voltmeter reads the voltage of 55 V (110 55) then the trans-
former is said to be in subtractive polarity as shown in Fig. 2.12.

Fig. 2.11 Testing of additive

polarity H1
X1
VH1H 2
110 V 55 V

H2
X2

165 V
64 2 Transformer: Principles and Practices

H1
X1
VH1H 2
110 V 55 V

H2
X2

V
55 V

Fig. 2.12 Testing of subtractive polarity

2.10 Three-Phase Transformer

A three-phase power transformer is used at the power generating station to step-up

the voltage from 11 to 120 kV. Whereas in the power distribution substation, the
three-phase voltage is again stepped down to 11 kV voltage through a three-phase
distribution transformer.

A1 B1 C1

N11 N 21 N 31

N12 N 22
N 32

a1 b1 c1

Fig. 2.13 Three windings on a common core and wye-delta connection

2.10 Three-Phase Transformer 65

N11 N12 N 21 N 22

N 31 N 32

Fig. 2.14 Three single-phase transformers

Therefore, a three-phase transformer can be made either by three windings

wound on a common core or by three single-phase transformer connected together
in a three-phase bank.
The rst approach is a cheaper one that results in a transformer with smaller size
and less weight. The main disadvantage of the rst approach is that if one phase
becomes defective, then the whole transformer needs to be replaced. Whereas in the
second approach, if one of the transformers becomes defective then the system can
be given power by an open delta at a reduced capacity. In this case, the defective
transformer is normally replaced by a new one. A three-phase transformer with
wye-delta connection is shown in Fig. 2.13 and the three single-phase transformers
are shown in Fig. 2.14.

2.11 Transformer Vector Group

The most common congurations of a three-phase transformer are the delta and star
congurations, which are used in the power utility company. The primary and
secondary windings of a three-phase transformer are connected either in the same
(delta-delta or star-star), or different (delta-star or star-delta) conguration-pair. The
secondary voltage waveforms of a three-phase transformer are in phase with the
primary waveforms when the primary and secondary windings are connected in the
same conguration. This condition is known as no phase shift condition. If the
primary and secondary windings are connected in different conguration pair then
the secondary voltage waveforms will differ from the corresponding primary
66 2 Transformer: Principles and Practices

Fig. 2.15 Representation of

vector groups with clock
A A
a a
N n N n
0 shift 30 lag

A A
a
N n N n
180 shift +30 lead
a

voltage waveforms by 30 electrical degrees. This condition is called a 30 phase

shift condition. The windings and their position to each other are usually marked
by vector group. The vector group is used to identify the phase shift between the
primary and secondary windings. In the vector group, the secondary voltage may
have the phase shift of 30 lagging or leading, 0 i.e., no phase shift or 180 reversal
with respect to the primary voltage. The transformer vector group is labeled by
capital and small letters plus numbers from 1 to 12 in a typical clock-like diagram.
The capital letter indicates primary winding and small letter represents secondary
winding. In the clock diagram, the minute hand represents the primary line to
neutral line voltage, and its place is always in the 12. The hour hand represents the
secondary line to neutral voltage and its position in the clock changes based on the
phase shift as shown in Fig. 2.15.
There are four vector groups used in the three-phase transformer connection.
These vector groups are (i) Group I: 0 oclock, zero phase displacement (Yy0, Dd0,
Dz0), (ii) Group II: 6 oclock, 180 phase displacement (Yy6, Dd6, Dz6),
(iii) Group III: 1 oclock, 30 lag phase displacement (Dy1, Yd1, Yz1), and
(iv) Group IV: 11 oclock, 30 lead phase displacement (Dy11, Yd11, Yz11). Here,
Y represents wye connection, D represents delta connection and z represents the
zigzag connection. The connection diagrams for different combinations are shown
in Figs. 2.16, 2.17, 2.18, 2.19, 2.20, 2.21, 2.22, 2.23, 2.24, 2.25, 2.26 and 2.27.
2.11 Transformer Vector Group 67

C Y/y/0
C2
c
c2
A1 A2 a1 a2
C1 c1 a
B1 A b1

b b2
B2
B
A1 A2 A a1 a2 a

B1 B2 b1 b2
N B n b

C1 C2 c1 c2
C c

Fig. 2.16 Connection of Y-y-0

C C2 D/d/0
B1
c c2
b1
C1
A c1
a
A2 a2
b2
B2 b a1
B A1

A1 A2 A a1 a2 a

B1 B2 b1 b2
B b

C1 C2 c1 c2
C c

Fig. 2.17 Connection of D-d-0

68 2 Transformer: Principles and Practices

C C2 D/z/0
c2
B1 a2
a4
c4 c1 a1
C1
A c3 b3 a3
A2 b1

B2 c4
B A1 c b2 b4
c3
b1

a2 b2
a
c2 a4
a1
b3 c1 a3

b4
b

A1 A2 A a1 a2 a3 a4 a

B1 B2 b1 b2 b3 b4
B b
n
C1 C2 c1 c2 c3 c4
C c

Fig. 2.18 Connection of D-z-0

Fig. 2.19 Connection of C Y/d/1

Y-d-1
C2 b1 c c2
30
A1 A2
C1 c1
B1 A b2
b a1 a2 a

B2
B
A1 A2 A a1 a2 a

B1 B2 b1 b2
N B b

C1 C2 c1 c2
C c
2.11 Transformer Vector Group 69

D/y/1
C
A2 c c2
C1

A1 c1
b1
A a1 30
B2 a
b2 a2
b
C2
B B1

A1 A2 A a1 a2 a

B1 B2 b1 b2
B n b

C1 C2 c1 c2
C c

Fig. 2.20 Connection of D-y-1

C
C2 Y/z/1 c
c4
c3 c2
C1
A c1 a
B1 b1
A1 A2
a1 a2 a3 a4
b2
c4 b3
B2 c
B b4
c3
b
b1
a1 a2 b2
b3
c2
b4 c1 a
a3 a4
b

A1 A2 A a1 a2 a3 a4 a

B1 B2 b1 b2 b3 b4
N B b
n
C1 C2 c1 c2 c3 c4
C c

Fig. 2.21 Connection of Y-z-1

70 2 Transformer: Principles and Practices

Fig. 2.22 Connection of D/y/11

D-y-11 C C2
a2 a
B1 c
c2
a1 30
C1 c1
A b1
A2

b2
b
B2
B A1

A1 A2 A a1 a2 a

B1 B2 b1 b2
B n b

C1 C2 c1 c2
C c

Fig. 2.23 Connection of Y/d/11

Y-d-11 C C2
a
c a1 a2 a
30 c2 b1
30
A
C1
B1 A
A1 c1 b2
A2
b

B2
B

A1 A2 A a1 a2 a

B1 B2 b1 b2
N B b

C1 C2 c1 c2
C c
2.11 Transformer Vector Group 71

C
C2 Y/z/11
c4
c3 c2
C1
A c1
B1 b1
A1 A2
a1 a2 a3 a4
b2
B2 b3
B a3 a4 b4
c b1 a
c4
b2
c3 c2
a1 a2
c1

b3

b b4
A1 A2 A a1 a2 a3 a4 a

B1 B2 b1 b2 b3 b4
N B b
n
C1 C2 c1 c2 c3 c4
C c

Fig. 2.24 Connection of Y-z-11

Fig. 2.25 Connection of C b

C2 Y/y/6
Y-y-6 b1

C1 a1 a2
B1 A a b
A1 A2 c2 2

B2 c1 c
B a
A1 A2 A a1 a2

b
N B1 B2 b1 b2 n
B
c
C1 C2 c1 c2
C
72 2 Transformer: Principles and Practices

C C2 a1 b
C C2 D/d/6 b2
b B1
A1 A2 b1 a2
B1 A
C1 C1 a
a1 a2 A c1
b
a c2 2 A2
B2 b1
B c2 c
B2
c1 c A1
B

A1 A2 A a1 a2
a

B1 B2 b1 b2
B b

C1 C2 c1 c2
C c

Fig. 2.26 Connection of D-d-6

C
C2 D/z/6
B1
c c4 a4
C1 a
c3 c2 a3
A
A2 c1 a2
b1 a1
B2 b
A1 b3 b2
B
b3
a4 c2
b4
a3 c1 a2 b4
a a1 b
b1
b2
c4
c3 c
a
A1 A2 a1 a2 a3 a4
A

B1 B2 b2
n b1 b3 b4
B b

C1 C2 c1 c2 c3 c4
C
c

Fig. 2.27 Connection of D-y-6

2.12 Voltage Regulation of a Transformer 73

2.12 Voltage Regulation of a Transformer

Different types of loads like domestic, commercial and industrial are usually con-
nected with the secondary winding of a transformer. All these loads are operated
with a constant magnitude of voltage. The secondary voltage of a transformer under
operation changes due to voltage drop across the internal impedance and the load.
The voltage regulation of a transformer is used to identify the characteristic of the
secondary side voltage changes under different loading conditions. The voltage
regulation of a transformer is dened as the difference between the no-load terminal
voltage (V2NL ) to full load terminal voltage (V2FL ) and is expressed as a percentage
of full load terminal voltage. It is therefore can be expressed as,

V2NL  V2FL E2  V2
Voltage regulation  100 %  100 % 2:61
V2FL V2

Figure 2.28 shows an approximate equivalent circuit referred to the secondary

without no-load circuit to nd the voltage regulation for different power factors.
Phasor diagrams for different power factors are shown in Fig. 2.29 where the
secondary voltage V2 is considered as the reference phasor.
The phasor diagram with a unity power factor is shown in Fig. 2.29a and the
phasor form of the secondary induced voltage for a unity power factor can be
written as,

E2 V2 I2 R02 jX02 2:62

Figure 2.29b shows the phasor diagram for a lagging power factor, and from this
diagram, the following expressions can be written,

AC V2 cos /2 2:63

BC DE V2 sin /2 2:64

CD BE I2 R02 2:65

EF I2 X02 2:66

Fig. 2.28 Approximate R 02 I2 X 02

equivalent circuit referred to
secondary +
+
E2 V2 ZL


74 2 Transformer: Principles and Practices

(a) E2 U (b)
E2
I 2 X 02 F
I 2 Z 02
Z
X I2 V2 Y I 2 R02 V2 I 2 X 02

(c) 2 B
Q A
I 2 R02
P I2
E2 E
R C

I 2 X 02 D
O
I2

I 2 R02
2
M V2 N

Fig. 2.29 Phasor diagram for different power factors

From the right angle triangle-ADF, the expression of E2 can be derived as,

AF 2 AD2 DF 2 2:67

AF 2 AC CD2 DE EF2 2:68

Substituting equations from (2.63) to (2.66) into Eq. (2.68) yields,

q
E2 V2 cos /2 I2 R02 2 V2 sin /2 I2 X02 2 2:69

In phasor form, Eq. (2.69) can be written as,

E2 V2 cos /2 I2 R02 jV2 sin /2 I2 X02 2:70

Figure 2.29c shows the phasor diagram for a leading power factor and from this
diagram, the following expressions can be written,

MR V2 cos /2 2:71

RN OQ V2 sin /2 2:72

RQ NO I2 R02 2:73
2.12 Voltage Regulation of a Transformer 75

PO I2 X02 2:74

The expression of E2 from the right angled triangle MQP can be derived as,

MP2 MQ2 QP2 2:75

MP2 MR RQ2 OQ  PO2 2:76

Substituting equations from (2.71) to (2.74) into Eq. (2.76) yields,

q
E2 V2 cos /2 I2 R02 2 V2 sin /2  I2 X02 2 2:77

In phasor form, Eq. (2.77) can be written as,

E2 V2 cos /2 I2 R02 jV2 sin /2  I2 X02 2:78

Example 2.5 The primary coil resistance and reactance of a 200/400 V single-phase
transformer are 0.3 and 0:6 X, respectively. The secondary coil resistance and
reactance are 0.8 and 1:6 X, respectively. Calculate the voltage regulation if the
secondary current of the transformer is 10 A at a 0.8 pf lagging.
Solution
The value of the turns ratio is,

V1 200
a 0:5
V2 400

The value of the total resistance referred to the secondary is,

R1 0:3
R02 R2 0:8 2X
a2 0:25

The total reactance referred to the primary is,

X1 0:6
X02 X2 1:6 4X
a2 0:25

The no-load voltage is,

E2 V2 cos /2 I2 R02 jV2 sin /2 I2 X02

E2 400  0:8 10  2 j400  0:6 40
E2 440:5j39:5 V
76 2 Transformer: Principles and Practices

The voltage regulation can be determined as,

E2  V2
Voltage regulation  100 %
V2
440:5  400
Voltage regulation  100 % 10 %
400
Practice problem 2.5
A 110/220 V single-phase transformer has the resistance of 0:2 X and a reactance of
0:8 X in the primary winding. The resistance and reactance in the secondary
winding are 0.9 and 1:8 X, respectively. Calculate the voltage regulation, when the
secondary current is 6 A at a 0.85 power factor leading.

2.13 Efciency of a Transformer

The efciency is an important parameter to identify the characteristics of any

machine. The efciency g, of any machine can be dened as the ratio of its output to
the input. Mathematically, it can be expressed as,

output input  losses losses

g 1 2:79
input input input

Let us consider the following:

Pout is the output power, in W,
Pin is the input power, in W,
Plosses is the total losses, in W.
Equation (2.79) can be modied as,

Pout Plosses
g 1 2:80
Pin Pin

It is worth nothing that the efciency of a transformer is generally higher than other
electrical machines because the transformer has no moving parts.

2.14 Iron and Copper Losses

The iron loss of a transformer is often called as core loss, which is a result of an
alternating flux in the core of the transformer. The iron loss consists of the eddy
current loss and the hysteresis loss. In the transformer, most of the flux transferred
from the primary coil to the secondary coil through low reluctance iron path. A few
2.14 Iron and Copper Losses 77

portion of that alternating flux links with the iron parts of the transformer. As a
result, an emf is induced in the transformer core. A current will flow in that parts of
the transformer. This current does not contribute in output of the transformer but
dissipated as heat. This current is known as eddy current and the power loss due to
this current is known as eddy current loss. The eddy current loss Pe is directly
proportional to the square of the frequency (f) times the maximum magnetic flux
density Bm and the eddy current loss can be expressed as,

Pe ke f 2 B2m 2:81

where ke is the proportionality constant.

Steel is a very good ferromagnetic material which is used for the core of a
transformer. This ferromagnetic material contains number of domains in the
structure and magnetized easily. These domains are like small magnets located
randomly in the structure. When an mmf is applied to the core then those domains
change their position. After removing mmf, most of the domains come back to their
original position and remaining will be as it is. As a result, the substance is slightly
permanently magnetized. An additional mmf is required to change the position of
the remaining domains. Therefore, hysteresis loss is dened as the additional
energy is required to realign the domains in the ferromagnetic material. The hys-
teresis loss Ph is directly proportional to the frequency (f) and 2.6th power of the
maximum magnetic flux density Bm and the expression of hysteresis loss is,

Ph kh fB2:6
m 2:82

where ke is the proportionality constant.

Now that the magnetic flux density is usually constant, Eqs. (2.81) and (2.82)
can be modied as,

Pe / f 2 2:83

Ph / f 2:84

Practically, hysteresis loss depends on the voltage and the eddy current loss
depends on the current. Therefore, total losses of the transformer depend on the
voltage and the current not on the power factor. That is why the transformer rating
is always represented in kVA instead of kW.
In the transformer, copper losses occur due to the primary and the secondary
resistances. The full load copper losses can be determined as,

Pculoss I12 R1 I22 R2 2:85

Pculoss I12 R01 I22 R02 2:86

78 2 Transformer: Principles and Practices

2.15 Condition for Maximum Efciency

The expression of the output power of a transformer is,

Pout V2 I2 cos /2 2:87

The expression of the copper loss is,

Pcu I22 R02 2:88

The expression of an iron loss is,

Piron Peddy Phys 2:89

According to Eq. (2.79), the efciency can be expressed as,

output output
g 2:90
input output losses

Substituting Eqs. (2.87), (2.88) and (2.89) into Eq. (2.90) yields,

V2 I2 cos /2
g 2:91
V2 I2 cos /2 Piron Pcu

V2 cos /2
g I22 R02
2:92
V2 cos /2 Piron
I2 I2

The terminal voltage at the secondary side is considered to be constant in case of a

normal transformer. For a given power factor, the secondary current is varied with
the variation of load. Therefore, the transformer efciency will be maximum, if the
denominator of Eq. (2.92) is minimum. The denominator of Eq. (2.92) will be
minimum, for the following condition.
 
d Piron I22 R02
V2 cos /2 0 2:93
dI2 I2 I2

Piron
 R02 0 2:94
I22

Piron I22 R02 2:95

From Eq. (2.95), it is concluded that the efciency of a transformer will be

maximum, when the iron loss is equal to the copper loss. From Eq. (2.95), the
expression of secondary current can be written as,
2.15 Condition for Maximum Efciency 79

r
Piron
I2 2:96
R02

For maximum efciency, the load current can be expressed as,

r
Piron
I2g 2:97
R02

Equation (2.97) can be re-arranged as,

s
Piron
I2g I2 2 2:98
I2 R02

Multiplying both sides of Eq. (2.98) by the secondary rated voltage V2 yields,
s
Piron
V2 I2g V 2 I2 2 2:99
I2 R02
s
iron loss
VImax efficiency VIrated  2:100
full load copper loss

Example 2.6 A 30 kVA transformer has the iron loss and full load copper loss of
350 and 650 W, respectively. Determine the (i) full load efciency, (ii) output kVA
corresponding to maximum efciency, and (iii) maximum efciency. Consider that
the power factor of the load is 0.6 lagging.
Solution

(i) The total value of full load loss is,

Ptloss 350 650 1000 W 1 kW

The output power at full load is,

Pout 30  0:6 18 kW

The input power at full load is,

Pin 18 1 19 kW
80 2 Transformer: Principles and Practices

The efciency at full load is,

18
g  100 94:74 %
19

(ii) The output kVA corresponding to maximum efciency is,

r
Iron loss
kVArated 
Cu loss at full load
r
350
30  22 kVA
650

The output power is,

Po1 22  0:6 13:2 kW

(iii) For maximum efciency, iron loss is equal to copper loss.

The total value of the loss is,

Ptloss1 2  350 700 W

The value of the input power is,

Pin1 13:2 0:7 13:9 kW

The efciency is,

13:2
g  100 94:96 %
13:9

Practice problem 2.6

A 200 kVA transformer is having an iron loss of 1.5 kW and a copper loss of 5 kW
at full load condition. Find the kVA rating at which the efciency is maximum.
Also, nd the efciency at a unity power factor.

2.16 Transformer Tests

The equivalent circuit parameters are very important to characterize the perfor-
mance of transformer. The parameters of a transformer equivalent circuit can be
determined by the open circuit and the short circuit tests.
2.16 Transformer Tests 81

2.16.1 Open Circuit Test

The main objectives of the open circuit test are to determine the no-load current and
iron loss. The components of the no-load current are used to determine the no-load
circuit resistance and reactance.
In an open circuit test, the secondary side is considered to be open circuit, and the
primary coil is connected to the source as shown in Fig. 2.30a, where all measuring
instruments are connected in the primary side. A specic alternating voltage is
applied to the primary winding. Then the wattmeter will measure the iron loss and
small amount of copper loss. The ammeter and voltmeter will measure the no-load
current and the voltage, respectively. Since, the no-load current is very small, the
copper losses can be neglected. Then the wattmeter reading can be expressed as,

P0 V1 I0 cos /0 2:101

From Eq. (2.101), the no-load power factor can be determined as,

P0
cos /0 2:102
V1 I0

The working and magnetizing components of the current can be determined as,

Iw I0 cos /0 2:103

Im I0 sin /0 2:104

Then the no-load circuit resistance and reactance can be determined as,

V1
R0 2:105
Iw

V1
X0 2:106
Im

(a) (b)
I0
A
N1 N2
Iw
+ +
Im
V1 V V1 R 0 X0

Fig. 2.30 Connection diagrams for open circuit test and no-load circuit
82 2 Transformer: Principles and Practices

Example 2.7 A 200/400 V, 50 Hz single-phase transformer has the no-load test

data of 200 V, 0.6 A, 80 W. Calculate the no-load circuit resistance and reactance.
Solution
The power factor can be determined as,

P0 80
cos /0 0:67
V1 I0 200  0:6
sin /0 0:74

The values of the working and magnetizing components of the no-load current are,

Iw I0 cos /0 0:6  0:67 0:4 A

Im I0 sin /0 0:6  0:74 0:44 A

The no-load circuit parameters can be determined as,

V1 200
R0 500 X
Iw 0:4
V1 200
X0 454:5 X
Im 0:44

2.16.2 Short Circuit Test

The main objectives of the short circuit test are to determine the equivalent resis-
tance, reactance, impedance and full load copper loss. In this test, the supply
voltage and the measuring instruments (e. g,. wattmeter, ammeter) are connected to
the primary side and the secondary winding is shorted out by a wire as shown in
Fig. 2.31, or connected with an ammeter. The primary voltage is adjusted until the
current in the short-circuited winding is equal to the rated primary current. Under
this condition, the wattmeter will measure the full load copper loss and it can be
written as,

Psc Isc Vsc cos /sc 2:107

From Eq. (2.107), the short circuit power factor can be calculated as,

Psc
cos /sc 2:108
Isc Vsc
2.16 Transformer Tests 83

A
N1 N2
+ +
V Isc
V1 Vsc

Fig. 2.31 Connection diagram for short circuit test

The equivalent impedance can be calculated as,

Vsc
Z01 Zeq 2:109
Isc

In addition, the equivalent resistance and reactance can be calculated as,

R01 Z01 cos /sc 2:110

X01 Z01 sin /sc 2:111

Example 2.8 A 25 kVA, 2200/220 V, 50 Hz single-phase transformers low

voltage side is short-circuited and the test data recorded from the high voltage side
are P 150 W, I1 5 A and V1 40 V. Determine the (i) equivalent resistance,
reactance and impedance referred to primary, (ii) equivalent resistance, reactance
and impedance referred to secondary, and (iii) voltage regulation at unity power
factor.
Solution

(i) The parameters referred to primary are,

V1 40
Z01 8X
I1 5
P 150
R01 2 6X
I1 25
 
6
/ cos1 41:4
8
X01 Z01 sin / 8 sin 41:4 5:2 X
84 2 Transformer: Principles and Practices

(ii) The turns ratio is,

V1 2200
a 10
V2 220

The parameters referred to secondary are,

Z01 8
Z02 0:08 X
a2 100
R01 6
R02 2 0:06 X
a 100
X01 5:2
X02 2 0:052 X
a 100

(iii) The secondary side current is,

25;000
I2 113:6 A
220

The secondary induced voltage is,

E2 V2 I2 Z02 220 113:6  0:08 229 V

The voltage regulation is,

E2  V2 229  220
VR 4%
V2 220

Practice problem 2.7

The no-load test data of a 220/2200 V, 50 Hz single-phase transformer are 220 V,
0.4 A, 75 W. Calculate the no-load circuit resistance and reactance.
Practice problem 2.8
A 30 kVA, 2300/220 V, 50 Hz single-phase transformers low voltage side is
short-circuited by a thick wire. The test data recorded from the high voltage side are
P 400 W, I1 8:5 A and V1 65 V. Find the (i) equivalent resistance, reactance
and impedance referred to primary and (ii) equivalent resistance, reactance and
impedance referred to secondary, and (iii) voltage regulation at a 0.6 lagging power
factor.
2.17 Autotransformer 85

2.17 Autotransformer

A small rating transformer with a variable voltage output is usually used in the
educational laboratory as well as in the testing laboratory. This type of small rating
transformer with a variable output is known as autotransformer. An autotransformer
has one continuous winding that is common to both the primary and the secondary.
Therefore, in an autotransformer, the primary and secondary windings are con-
nected electrically. The advantages of an autotransformer over a two-winding
transformer include lower initial investment, lower leakage reactance, lower losses
compared to conventional transformer and lower excitation current.
An autotransformer with primary and secondary windings is shown in Fig. 2.32.
In this connection, the sufx c indicates the common winding and the sufx
s indicates the series winding. From Fig. 2.32, the following equations can be
written as,

Ns Ic
a 2:112
Nc Is

Vs Ns
a 2:113
Vc Nc

The total voltage in the primary side is,

 
Vs
V1 Vs Vc Vc 1 2:114
Vc

Substituting Eq. (2.113) into Eq. (2.114) yields,

V1
1 a 2:115
Vc

VL 1
2:116
V1 1 a

Fig. 2.32 Connection

diagram for an
autotransformer Is
+ Ns IL
V1
+
Nc
VL
Ic

86 2 Transformer: Principles and Practices

Where the voltage at the load is equal to the voltage at the common terminals i.e.,
VL Vc .
The expression of the load current can be written as,

IL Is Ic aIs Is 2:117

IL 1 aIs 2:118

IL
1 a 2:119
Is

Example 2.9 Figure 2.33 shows a single-phase 120 kVA, 2200/220 V, 50 Hz

transformer which is connected as an autotransformer. The voltages of the upper
and lower parts of the coil are 220 and 2200 V, respectively. Calculate the kVA
rating of the autotransformer.
Solution
The current ratings of the respective windings are,

120;000
Ipq 545:5 A
220
120;000
Iqr 54:5 A
2200

The current in the primary side is,

I1 545:5 54:5 600 A

The voltage across the secondary side is,

V2 2200 220 2420 V

Fig. 2.33 An p
autotransformer with a
specic voltage I pq +

I1
2420 V
q
+
-
2200 V
Iqr
- r
2.17 Autotransformer 87

Fig. 2.34 An p
autotransformer with a
specic voltage I pq
+
I1
q 1320 V
+
1100 V -
Iqr
- r

Therefore, the kVA ratings of an autotransformer,

600  2200
kVA1 1320 kVA
1000
545:5  2420
kVA2 1320 kVA
1000
Practice problem 2.9
A single-phase 100 kVA, 1100/220 V, 50 Hz transformer is connected as an
autotransformer as shown in Fig. 2.34. The voltages of the upper and lower parts of
the coil are 220 and 1100 V, respectively. Determine the kVA rating of the
autotransformer.

2.18 Parallel Operation of a Single-Phase Transformer

Nowadays, the demand of load is increasing with the increase in population and
industrial sector. Sometimes, it is difcult to meet the excess demand of power by
the existing single unit transformer. Therefore, an additional transformer is required
to connect in parallel with the existing one. The following points should be con-
sidered for making parallel connections of transformers:
Terminal voltage of both transformers must be the same.
Polarity must be same for both transformers.
For both transformers, the percentage impedances should be equal in magnitude.
Ratio of R to X must be the same for both transformers.
Phase sequences and phase shifts must be the same (for three-phase
transformer).
88 2 Transformer: Principles and Practices

2.19 Three-Phase Transformer Connections

The primary and secondary windings of the transformer may be connected in either
by wye (Y) or delta (D). Three-phase transformer connections are classied into
four possible types; namely, Y-Y(wye-wye), Y-D (wye-delta), D-Y(delta-wye) and
D-D (delta-delta).

2.19.1 Wye-Wye Connection

Figure 2.35 shows the Y-Y connection diagram. This type of connection of a
three-phase transformer is rarely used for large amount of power transmission.
Neutral point is necessary for both primary and secondary sides in some cases. In
balanced loads, this type of connection works satisfactorily and provides neutral to
each side for grounding. At the primary side, the phase voltage can be written as,

VL1
VP1 p 2:120
3

The secondary phase voltage can be written as,

VL2
VP2 p 2:121
3

The ratio of the primary line voltage to the secondary line voltage of this connection
is,

VL1
a 2:122
VL2
p
3VP1 VP1
a p 2:123
3VP2 VP2

Fig. 2.35 Y-Y connection B Primary

diagram A B C N
A

b
a

c a Secondary b c n
2.19 Three-Phase Transformer Connections 89

2.19.2 Wye-Delta Connection

The wye-delta connection is mainly used at the substation where the voltage is
stepped down. In this connection, the current in the secondary coil is 57.7 % of the
load current. At the primary side of this connection, a proper copper wire is used to
ground the neutral point. Figure 2.36 shows the connection diagram of the
wye-delta transformer. In this connection, the expression of the primary line voltage
is,
p
VL1 3VP1 2:124

At the secondary side, the line voltage is,

VL2 VP2 2:125

The ratio of primary phase voltage to secondary phase voltage is,

VP1
a 2:126
VP2

The ratio of primary line voltage to secondary line voltage is,

p
VL1 3VP1 p
3a 2:127
VL2 VP2

The primary phase current is,

IP1 IL1 2:128

In this case, the turns ratio is,

IP2
a 2:129
IP1

Fig. 2.36 Wye-delta B A B C N

connection diagram Primary

A
C
b

a c
Secondary a c
b
90 2 Transformer: Principles and Practices

The expression of the secondary phase current is,

IP2 aIP1 2:130

The secondary line current is,

p p
IL2 3IP2 3aIP1 2:131

2.19.3 Delta-Wye Connection

The delta-wye connection is generally used at the power generating station to step
the voltage. Figure 2.37 shows the connection diagram of a delta-wye transformer.
In this connection, the expression of the primary line voltage is,

VL1 VP1 2:132

The line voltage at the secondary side is,

p
VL2 3VP2 2:133

The ratio of primary line voltage to secondary line voltage is,

VL1 VP1 a
p p 2:134
VL2 3VP2 3

The phase current at the primary side is,

1
IP1 p IL1 2:135
3

Fig. 2.37 Delta-wye B

connection diagram
A B C
A
C
Primary
b

a
c
Secondary a b c
n
2.19 Three-Phase Transformer Connections 91

In this connection, the turns ratio is,

IP2
a 2:136
IP1

In this case, the secondary phase current is,

IP2 aIP1 2:137

The secondary line current is,

IL2 IP2 aIP1 2:138

2.19.4 Delta-Delta Connection

The delta-delta connection is generally used for both high voltage and low voltage
rating transformers where insulation is not an important issue. The connection
diagram for delta-delta transformer is shown in Fig. 2.38. In this case, the primary
line voltage is,
VL1 VP1 2:139

The secondary line voltage is,

VL2 VP2 2:140

The ratio of line-to-line voltage of this connection is,

VL1 VP1
a 2:141
VL2 VP2

Fig. 2.38 Delta-delta B

connection diagram A B C

A
C
Primary

a c
Secondary
a b c
92 2 Transformer: Principles and Practices

The secondary line current is,

p
IL2 3 IP2 2:142

The output capacity in delta-delta connection can be expressed as,

p
P0DD 3VL2 IL2 2:143

Substituting Eq. (2.142) into Eq. (2.43) yields,

p p
P0DD 3VL2  3IP2 3VL2 IP2 2:144

The remaining two transformers are able to supply three-phase power to the load
terminal if one of the transformer is removed from the connection. This type of
three-phase power supply by two transformers is known as open delta or V-V
connection. This open delta connection is able to supply three-phase power at a
reduced rate of 57.7 %. The connection diagram for open delta connection is shown
in Fig. 2.39.
In the V-V connection, the secondary line current is,

IL2 IP2 2:145

The output capacity in V-V connection is,

p
P0VV 3VL2 IP2 2:146

The ratio of delta-delta output capacity to the V-V output capacity is,
p
P0VV 3VL2 IP2
0:577 2:147
P0DD 3VL2 IP2

Fig. 2.39 Open delta or V-V B

connection diagram A B C

A
C
Primary
b

a c
Secondary
a b c
2.19 Three-Phase Transformer Connections 93

Example 2.10 A three-phase transformer is connected to an 11 kV supply and

draws 6 A current. Determine (i) line voltage at the secondary side, and also (ii) the
line current in the secondary coil. Consider the turns ratio of the transformer is 11.
Also, consider delta-wye and wye-delta connections.
Solution
Delta-wye connection:
The phase voltage at the primary side is,

VP1 VL1 11 kV

The phase voltage at the secondary side is,

VP1 11;000
VP2 1000 V
a 11

(i) The line voltage at the secondary is,

p p
VL2 3VP2 3  1000 1732 V

(ii) The phase current in the primary is,

IL1 11
IP1 p p 6:35 A
3 3

The line current in the secondary is,

IL2 IP2 aIP1 11  6:35 69:85 A

Wye-delta connection:
The line voltage at the primary side is,

VL1 11 kV

The phase voltage at the primary side is,

VL1 11;000
VP1 p p 6350:85 V
3 3
94 2 Transformer: Principles and Practices

(i) The phase voltage at the secondary side is,

VP1 6350:85
VP2 577:35 V
a 11

The line voltage at the secondary is,

VL2 VP2 577:35 V

(ii) The phase current in the secondary is,

IP2 aIP1 11  6 66 A

The line current in the secondary is,

p p
IL2 3IP2 3  66 114:32 A

Practice problem 2.10

A three-phase transformer is connected to the 33 kV supply and draws 15 A current.
Calculate (i) the line voltage at the secondary side, and also (ii) the line current in
the secondary winding. Consider the turns ratio of the transformer is 8 and
wye-delta connection.

2.20 Instrument Transformers

The magnitude of the voltage and the current are normally high in the power system
networks. To reduce the magnitude of the voltage and current, instrument trans-
formers are used. There are two types of instrument transformers; namely, current
transformer (CT) and potential transformer (PT) . If a power system carries an
alternating current greater than 100 A, then it is difcult to connect measuring
instruments like low range ammeter, wattmeter, energy meter and relay.
The current transformer is then connected in series with the line to step down the
high magnitude of the current to a rated value of about 5 A for the ammeter and the
current coil of the wattmeter. The diagram of a current transformer is shown in
Fig. 2.40. If the system voltage exceeds 500 V, then it is difcult to connect
measuring instruments directly to the high voltage. The potential transformer is then
used to step down to a suitable value of the voltage at the secondary for supplying
the voltmeter and the voltage coil of the wattmeter. The secondary of the instrument
transformer is normally grounded for safety reason. The connection diagram of a
potential transformer is shown in Fig. 2.41.
2.20 Instrument Transformers 95

Fig. 2.40 Connection I To load

diagram of current
transformer

Fig. 2.41 Connection

diagram of potential
transformer
V

Exercise Problems

2:1 A single-phase transformer is having the primary voltage of 240 V. The

number of turns at the primary and secondary coils are 250 and 50,
respectively. Determine the secondary voltage.
2:2 A single-phase transformer is having the secondary voltage of 100 V. The
number of turns at the primary and secondary windings are 500 and 50,
respectively. Calculate the primary voltage.
2:3 The 100 A current flows in the primary coil of a single-phase transformer.
Calculate the secondary current with the turns ratio of 0.05.
2:4 The number of turns at the primary and secondary windings of a single-phase
transformer are 500 and 100, respectively. Find the primary current if the
secondary current is 10 A.
2:5 The ratio of the primary current to the secondary current of a single-phase
transformer is 1:10. Find the voltage ratio. Also, nd the secondary voltage if
the primary voltage is 100 V.
2:6 The turns ratio of a single-phase transformer is 1:4. The secondary coil has
5000 turns and 60 V. Find the voltage ratio, primary voltage and number of
turns.
2:7 The voltage ratio of a single-phase transformer is 5:1. The voltage and
number of turns at the primary coil are found to be 1100 V and 500,
respectively. Calculate the voltage and secondary number of turns at the
secondary coil.
2:8 A single-phase transformer is connected to the 120 V source draws 4 A
current. Calculate the current in the secondary coil when the transformer
steps up the voltage to 500 V.
96 2 Transformer: Principles and Practices

2:9 The number of turns at the primary and secondary coils of a single-phase
transformer are found to be 480 and 60, respectively. The transformer draws
a current of 0.6 A when connected to 120 V supply. Determine the current
and the voltage at the secondary coil.
2:10 The turns ratio of a 5 kVA single-phase transformer is found to be 2. The
transformer is connected to a 230 V, 50 Hz supply. If the secondary current
of a transformer is 6 A, then nd the primary current and secondary voltage.
2:11 The secondary number of turns of a 30 kVA, 4400/440 V single-phase
transformer is found to be 100. Find the number of primary turns, full load
primary and secondary currents.
2:12 A 5 kVA, 1100/230 V, 50 Hz single-phase transformer is installed near the
domestic area of a country. Find the turns ratio, primary and secondary full
load currents.
2:13 The number of turns of the primary winding of a single-phase 50 Hz
transformer is found to be 50. Find the value of the core flux, if the induced
voltage at this winding is 220 V.
2:14 The number of primary turns of a 60 Hz single-phase transformer is found to
be 500. Calculate the induced voltage in this winding, if the value of the core
flux is 0.05 Wb.
2:15 The maximum flux of a 3300/330 V, 50 Hz step-down single-phase trans-
former is found to be 0.45 Wb. Calculate the number of primary and sec-
ondary turns.
2:16 The cross sectional area of a 5 kVA, 2200/220 V, 50 Hz single-phase
step-down transformer is found to be 25 cm2 and a maximum flux density is
4 Wb/m2. Calculate the primary and secondary turns.
2:17 The number of turns at the primary and secondary of an ideal single-phase
transformer are found to be 500 and 250, respectively. The primary of the
transformer is connected to a 220 V, 50 Hz source. The secondary coil
supplies a current of 5 A to the load. Determine the (i) turns ratio, (ii) current
in the primary and (iii) maximum flux in the core.
2:18 The primary number of turns of a 4 kVA, 1100/230 V, 50 Hz single-phase
transformer is 500. The cross sectional area of the transformer core is 85 cm2.
Find the (i) turns ratio, (ii) number of turns in the secondary and (iii) maxi-
mum flux density in the core.
2:19 The primary and secondary turns of a single-phase transformer are 50 and
500, respectively. The primary winding is connected to a 220 V, 50 Hz
supply. Find the (i) flux density in the core if the cross sectional area is
250 cm2 and (ii) induced voltage at the secondary winding.
2:20 The primary coil number of turns of a single-phase 2200/220 V, 50 Hz
transformer is found to be 1000. Find the area of the core if the maximum
flux density of the core is 1.5 Wb/m2.
2:21 The maximum flux of a single-phase 1100/220 V, 50 Hz transformer is found
to be 5 mWb. The number of turns and the voltage at the primary winding
are found to be 900 and 1100 V, respectively. Determine the frequency of the
supply system.
Exercise Problems 97

2:22 The maximum flux density of a 6 kVA, 2200/220 V, 50 Hz single-phase

transformer is found to be 0.6 Wb/m2. The induced voltage per turn of the
transformer is 10 V. Calculate the (i) primary number of turns, (ii) secondary
number of turns, and (iii) cross sectional area of the core.
2:23 A single-phase transformer is having the primary voltage per turn is 20 V.
Find the magnetic flux density if the cross sectional area of the core is
0.05 m2.
2:24 The no load primary current of an 1100/230 V single-phase transformer is
found to be 0.5 A and absorbs a power of 350 W from the circuit. Find the
iron loss and magnetizing components of the no-load current.
2:25 A 3300 V/230 V single-phase transformer draws a no-load current of 0.5 A
at a power factor of 0.4 in an open circuit test. Determine the working and
magnetizing components of the no-load current.
2:26 A single-phase transformer draws a no-load current of 1.4 A from the 120 V
source and absorbs a power of 80 W. The primary winding resistance and
leakage reactance are found to be 0.25 and 1:2 X, respectively. Determine the
no-load circuit resistance and reactance.
2:27 Under no-load condition, a single-phase transformer is connected to a 240 V,
50 Hz supply and draws a current of 0.3 A at a 0.5 power factor. The number
of turns on the primary winding is found to be 600. Calculate the (i) maxi-
mum value of the flux in the core, (ii) magnetizing and working components
of the no load current, and (iii) iron loss.
2:28 The no-load current of a 440/110 V single-phase transformer is measured 0.8
A and absorbs a power of 255 W. Calculate the (i) working and magnetizing
components of the no-load current, (ii) copper loss in the primary winding if
the primary winding resistance is 1:1 X, and (iii) core loss.
2:31 The primary winding resistance and reactance of a 300 kVA, 2200/220 V
single-phase transformer are 2 and 9 , respectively. The secondary winding
resistance and reactance are found to be 0.02 and 0.1 , respectively. Find
the equivalent impedance referred to the primary and the secondary.
2:32 The primary winding resistance and reactance of a 200 kVA, 3300/220 V
single-phase transformer are found to be 5 and 12 , respectively. The same
parameters in the secondary winding are found to 0.02 and 0.05 ,
respectively. Find the equivalent impedance referred to the primary and the
secondary. Also, determine the full load copper loss.
2:33 A 1100/400 V single-phase transformer having the resistance of 5 and the
reactance of 9 in the primary winding. The secondary winding resistance
and reactance are found to be 0.6 and 1.1 respectively. Find the voltage
regulation when the secondary delivers a current of 5 A at a 0.9 lagging
power factor.
2:34 A 2200/220 V single-phase transformer having the resistance of 6 and the
reactance of 16 in the primary coil. The resistance and the reactance in
secondary winding are found to be 0.07 and 0.15 , respectively. Find the
voltage regulation when the secondary supplies a current of 6 A at a 0.86
power factor leading.
98 2 Transformer: Principles and Practices

2:35 The iron loss and full load copper loss of a 40 kVA transformer are found to
be 450 and 750 W, respectively. Calculate the (i) full load efciency,
(ii) output kVA corresponding to maximum efciency, and (iii) maximum
efciency. Consider the power factor of the load is 0.95 lagging.
2:36 The iron loss of a 40 kVA transformer is 50 % of the full load copper loss.
The full load copper loss is found to be 850 W. Calculate the (i) full load
efciency, (ii) output kVA corresponding to maximum efciency, and
(iii) maximum efciency. Assume the power factor of the load is 0.9 lagging.
2:37 The iron loss and full load copper loss of a 25 kVA transformer are found to
be 300 and 550 W, respectively. Find the (i) full load efciency, (ii) output
kVA corresponding to maximum efciency, and (iii) maximum efciency.
Assume the power factor of the load is 0.6 lagging.
2:38 The primary and secondary windings parameters of a 100 kVA, 2200/220 V
transformer are R1 0:6 X, X1 0:9 X, R2 0:007 X, X2 0:008 X. The
transformer is operating at a maximum efciency of 75 % of its rated load
with 0.9 lagging power factor. Calculate the (i) efciency of transformer at
full load, and (ii) maximum efciency, if the iron loss is 350 W.
2:39 A 200 kVA, 2400/240 V transformer has the primary and windings
parameters R1 20 X, X1 27 X, R2 0:18 X, X2 0:26 X. The trans-
former is operating at a maximum efciency of 80 % of its rated load with
0.8 pf lagging. Calculate the (i) efciency of the transformer at full load, and
(ii) maximum efciency if the iron loss is 400 W.
2:40 The low voltage side of a 30 kVA, 2400/220 V, 50 Hz single-phase trans-
former is short circuited. The test data recorded from the high voltage side
are 200 W, 6 A and 45 V. Find the (i) equivalent resistance, reactance and
impedance referred to the primary, (ii) equivalent resistance, reactance and
impedance referred to the secondary, and (iii) voltage regulation at 0.6 power
factor lagging.
2:41 The low voltage winding of a 25 kVA, 1100/220 V, 50 Hz single-phase
transformer is short circuited. The test data recorded from the high voltage
side are 156 W, 4 A and 50 V. Calculate the (i) equivalent resistance,
reactance and impedance referred to the primary, (ii) equivalent resistance,
reactance and impedance referred to the secondary, and (iii) voltage regu-
lation at 0.85 power factor leading.
2:42 The test data of a 10 kVA, 440/220 V, 50 Hz single-phase transformer are as
follows:
Open circuit test: 220 V, 1.4 A, 155 W;
Short circuit test: 20.5 V, 15 A, 145 W;
Calculate the approximate equivalent circuit parameters.
2:43 The open circuit test data of a single-phase transformer are recorded as the
220 V, 1.2 A and 145 W. Find the no-load circuit parameters.
Exercise Problems 99

Fig. P2.1 An p
autotransformer with a I pq
specic voltage +

I1
q 1320 V
+
1100 V
I qr
r

2:44 A single-phase 100 kVA, 1100/220 V transformer is connected as an auto-

transformer, which is shown in Fig. P2.1. The voltage of the upper portion
and lower portion of the coil are found to be 220 and 1100 V, respectively.
Calculate the kVA rating of the autotransformer.
2:45 A 200 kVA three-phase, 50 Hz core-type transformer is connected as
delta-wye and has a line voltage ratio of 1100/440 V. The core area and the
maximum flux density of the transformer are found to be 0:04 m2 and
2:3 Wb/m2 , respectively. Calculate the number of turns per phase of the
primary and secondary coils.
2:46 The number of turns in the primary and secondary coils are found to be 600
and 150, respectively. The transformer is connected to 11 kV, 50 Hz supply.
Find the secondary line voltage when the windings are connected as
(a) delta-wye, and (b) wye-delta.

References

1. T. Wildi, Electrical Machines, Drives and Power Systems, 6th edn. (Pearson Education
International, Upper Saddle River, 2006)
2. M.A. Salam, Fundamentals of Electrical Machines, 2nd edn. (Alpha Science, International Ltd.,
Oxford, 2012)
3. S.J. Chapman, Electric Machinery and Power System Fundamentals (McGraw-Hill Higher
Education, New York, 2002)
4. A.E. Fitzgerald, C. Kingsley Jr., S.D. Umans, Electric Machinery, 6th edn (McGraw-Hill
Higher Education, New York, 2003)
http://www.springer.com/978-981-10-0444-5