Cat

797F
MINING TRUCK

Specifications
Engine Transmission
Engine Model Cat C175-20 Forward 1 11.3 km/h 7 mph
Gross Power SAE J1995 2983 kW 4,000 hp Forward 2 15.2 km/h 9.5 mph
Net Power SAE J1349 2828 kW 3,793 hp Forward 3 20.5 km/h 12.7 mph
Bore 175 mm 6.9 in Forward 4 27.7 km/h 17.2 mph
Stroke 220 mm 8.7 in Forward 5 37.2 km/h 23.1 mph
Displacement 106 L 6,469 in3 Forward 6 50.3 km/h 31.2 mph
Power ratings apply at 1,750 rpm when tested under the specific Forward 7 67.6 km/h 42 mph
conditions for the specified standard. Reverse 11.9 km/h 7.4 mph
Ratings based on SAE J1995 standard air conditions of 25 C (77 F)
and 99 kPa (29.32 Hg) barometer. Power based on fuel having API Suspension
gravity of 35 at 16 C (69 F) and an LHV of 42 780 kJ/kg (18,390 Btu/lb) Effective Cylinder Stroke Front 313.6 mm 12.3 in
when engine is used at 30 C (38 F).
Effective Cylinder Stroke Rear 165.1 mm 6.5 in
No low altitude arrangement (LAA) engine derating required up to
Rear Axle Oscillation 4.0 degrees
2134 m (7,000 ft) altitude.
No high altitude arrangement (HAA) engine derating required up to
4877 m (16,000 ft) altitude. Body Hoists
Emission Standards. Where applicable, the Cat C175-20 engine is Pump Flow High Idle 1200 L/min 317 gal/min
compliant with current U.S. EPA emission standards. Relief Valve Setting Raise 24 200 kPa 3,510 psi
Body Raise Time High Idle 25 Seconds
Weights Approximate High Idle Body Lower Time Float 19 Seconds
Target Gross Machine Operating
Weight (GMW) 623 690 kg 1,375,000 lb Brakes
Body Weight Range 41 368- 91,200- Number of Discs per Side Front 10
61 235 kg 135,000 lb Number of Discs per Side Rear 15
Chassis Weight Range 210 630- 464,359- Outside Diameter 1067 mm 42 in
219 146 kg 483,134 lb Brake Surface 330 517 cm2 51,243 in2
Refer to the Cat Mining Truck 10/10/20 Payload Policy for maximum Standards ISO 3450:2011
gross machine weight limitations.
Body weight varies depending on body and liner configuration. Approximate Weights MSD II
Weight range for known applications.
Chassis weight with 100 percent fuel, hoist, body mounting group, Front Axle Empty 47.2%
rims and tires. Front Axle Loaded 33.3%
Rear Axle Empty 52.8%
Rear Axle Loaded 66.7%
Operating Specifications
Nominal Payload Capacity 363 tonnes 400 tons
Heaped SAE (2:1) Capacity 240-267 m3 314-350 yd3
Weight Distributions Approximate
Top Speed Loaded 67.6 km/h 42 mph Front Axle Empty 47.2%
Steer Angle 40 Degrees Rear Axle Empty 52.8%
Machine Clearance Turning Diameter 42 m 138 ft Front Axle Loaded 33.3%
Rear Axle Loaded 66.7%
Final Drives
Differential Ratio 1.276:1
Planetary Ratio 16.67:1
Total Reduction Ratio 21.26:1
Double reduction, planetary with full floating axles.
797F Mining Truck
Capacity MSD II 100% Fill Factor
Struck 188-213 m3 246-290 yd3
Heaped (SAE 2:1) 240-267 m3 314-350 yd3
Consult your local Cat dealer for truck body recommendations.
2

Service Refill Capacities 3

13

12
Fuel Tank 3785 L 1,000 gal 14
11
Cooling System 1160 L 306 gal 15
16
Crankcase 319 L 84 gal 10
45
Front Wheels, Each 61 L 16 gal 9
1
Final Drives, Each 185 L 49 gal
Differentials 1176 L 311 gal 8 17
Steering Tank 254 L 67 gal 7

5
Steering System (Includes Tank) 355 L 94 gal 4
6

Brake/Hoist Hydraulic Lines 830 L 219 gal 18

Brake/Hoist System (Includes Tank) 1600 L 441 gal 19

Brake/Hoist Tank 770 L 203 gal 20

Torque Converter Sump 303 L 80 gal

Torque Converter/Transmission System Dimensions (All dimensions are approximate)
(Includes Sump) 629 L 166 gal Dimensions are with standard body 290-6420.
1 Height to Top of ROPS Empty 6526 mm 21 ft 5 in
Tires 2 Overall Body Length 14 802 mm 48 ft 7 in
Tire 59/80R63 Michelin 3 Inside Body Length 9976 mm 32 ft 9 in
or Bridgestone 4 Overall Length 15 080 mm 49 ft 6 in
Productive capabilities of the 797F are such that, under certain job 5 Wheelbase 7195 mm 23 ft 7 in
conditions, TKPH (TMPH) capabilities of standard tires could be 6 Rear Axle to Tail 3944 mm 12 ft 11 in
exceeded and, therefore, limit production. 7 Loaded Ground Clearance 786 mm 2 ft 7 in
8 Dump Clearance 2017 mm 6 ft 7 in
ROPS 9 Loading Height Empty 6998 mm 23 ft 0 in
ROPS Standards 10 Inside Body Depth Maximum 3363 mm 11 ft 0 in
ROPS (Rollover Protective Structure) for cab offered by Caterpillar 11 Overall Height Body Raised 15 701 mm 51 ft 6 in
meets ISO 3471:2008 ROPS criteria. 12 Centerline Front Tire Width 6534 mm 21 ft 5 in
FOPS (Falling Objects Protective Structure) meets ISO 3449:2005 13 Engine Guard Clearance Loaded 1025 mm 3 ft 4 in
Level II FOPS criteria. 14 Outside Body Width 9755 mm 32 ft 0 in
15 Overall Canopy Width 9116 mm 29 ft 11 in
Sound 16 Inside Body Width 8513 mm 27 ft 11 in
Sound Standards 17 Front Canopy Height Empty 7709 mm 25 ft 4 in
The operator sound pressure level measured according to work cycle 18 Rear Axle Clearance Loaded 947 mm 3 ft 1 in
procedures specified in ISO 6394:2008 and 6396:2008 is 76 dB(A) for 19 Centerline Rear Dual Tire Width 6233 mm 20 ft 5 in
cab offered by Caterpillar when properly installed and maintained 20 Overall Tire Width 9529 mm 31 ft 3 in
and tested with doors and windows closed.
Hearing protection may be needed when operating with an open
operator station and cab (when not properly maintained or doors/
windows open) for extended periods or in a noisy environment.

Steering
Steering Standards ISO 5010:2007

For more complete information on Cat products, dealer services, andindustry solutions, visit us on the web atwww.cat.com AEHQ5884-07 (05-2017)
2017 Caterpillar Replaces AEHQ5884-06
All rights reserved
Materials and specifications are subject to change without notice. Featured machines in photos may include additional
equipment. See your Cat dealer for available options.
CAT, CATERPILLAR, SAFETY.CAT.COM, their respective logos, CaterpillarYellow and the Power Edge tradedress, as well
as corporate and product identity used herein, are trademarks ofCaterpillarand may notbeused without permission.