Scribd Logo
Upload

Welcome to Scribd!

  • 594 views

    MediaTek LinkIt Smart 7688 Duo Pin Out v1 3

    Uploaded by

    teguhscribd
    This document provides a summary of the LinkIt Smart 7688 Duo board: 1. It is based around the MediaTek MT7688 system on a chip which integrates an MIPS 24KEc 580MHz processor, WiFi/Bluetooth radio, and other peripherals. 2. It has various interfaces including USB host and device ports, analog and digital pins for expansion, JTAG interface, serial ports, and an onboard ATmega32U4 microcontroller. 3. It requires a regulated 3.3V power supply and has a reset button for the MPU and WiFi modules. Special care needs to be taken with the bootstrap pin on first power on.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    MediaTek LinkIt Smart 7688 Duo Pin Out v1 3

    Uploaded by

    teguhscribd
    594 views1 page
    This document provides a summary of the LinkIt Smart 7688 Duo board: 1. It is based around the MediaTek MT7688 system on a chip which integrates an MIPS 24KEc 580MHz processor, WiFi/Bluetooth radio, and other peripherals. 2. It has various interfaces including USB host and device ports, analog and digital pins for expansion, JTAG interface, serial ports, and an onboard ATmega32U4 microcontroller. 3. It requires a regulated 3.3V power supply and has a reset button for the MPU and WiFi modules. Special care needs to be taken with the bootstrap pin on first power on.

    Original Description:

    LinkIt Smart 7688 Duo

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a summary of the LinkIt Smart 7688 Duo board: 1. It is based around the MediaTek MT7688 system on a chip which integrates an MIPS 24KEc 580MHz processor, WiFi/Bluetooth radio, and other peripherals. 2. It has various interfaces including USB host and device ports, analog and digital pins for expansion, JTAG interface, serial ports, and an onboard ATmega32U4 microcontroller. 3. It requires a regulated 3.3V power supply and has a reset button for the MPU and WiFi modules. Special care needs to be taken with the bootstrap pin on first power on.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    594 views1 page

    MediaTek LinkIt Smart 7688 Duo Pin Out v1 3

    Uploaded by

    teguhscribd
    This document provides a summary of the LinkIt Smart 7688 Duo board: 1. It is based around the MediaTek MT7688 system on a chip which integrates an MIPS 24KEc 580MHz processor, WiFi/Bluetooth radio, and other peripherals. 2. It has various interfaces including USB host and device ports, analog and digital pins for expansion, JTAG interface, serial ports, and an onboard ATmega32U4 microcontroller. 3. It requires a regulated 3.3V power supply and has a reset button for the MPU and WiFi modules. Special care needs to be taken with the bootstrap pin on first power on.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    LinkIt Smart 7688 Duo

    TM

    GND
    POWER
    CONTROL
    DIGITAL PIN
    ANALOG PIN
    MPU EJTAG
    PWM PIN (on the bottom side)
    SERIAL PIN This is a bootstrap pin for MT7688. Make sure it's pull-low
    at power on, or the system will fail to boot up normally.
    CHIP PIN NAME
    Connected to MT7688 Chip Antenna
    I-PEX Connector (require HW rework)

    MPU RESET PORST_N PB3 D14 MISO GPIO 17


    P0 S0
    EPHY LED GPIO 43 EPHY_LED0_N PB2 D15 MOSI GPIO 16
    P1 S1
    ETHY RD+ MDI_RP_P0 PB1 D16 SCLK GPIO 15
    P2 S2
    ETHY RD- MDI_RN_P0 PB0 D17 SS GPIO 14
    P3 S3

    MT7688
    ETHY TD+ MDI_TP_P0 PD2 D0 EINT UART RX UART_TXD0
    P4 D0
    ETHY TD- MDI_TN_P0 PD3 D1 EINT UART TX UART_RXD0
    P5 D1
    USB D+ USB_DP PD1 D2 EINT SDA
    P6 D2
    USB D- USB_DM PD0 D3 EINT SCL PWM
    P7 D3
    UART TX2 GPIO 20 UART_TXD2 PD4 D4 ADC

    ATmega32U4
    P8 D4
    UART RX2 GPIO 21 UART_RXD2 PC6 D5 PWM
    P9 D5
    GND PD7 D6 ADC PWM
    GND D6
    Requires a regulated 3.3V, 3V3 PE6 D7 EINT GPIO 0
    3V3 D7
    if a higher voltage is used, VCC PB4 D8 ADC
    the board will be damaged. VCC D8
    5V PB5 D9 ADC PWM
    5V D9
    ADC D18 PF0 PB6 D10 ADC PWM
    A0 D10
    ADC D19 PF1
    ATmega32U4

    PB7 D11 PWM


    A1 D11
    ADC D20 PF4 PD6 D12 ADC PWM
    A2 D13 D12
    ADC D21 PF5 PC7 D13 PWM D13 LED
    A3 MPU WiFi MCU D13
    ADC D22 PF6 RST MCU RESET GPIO 3
    A4 RST
    ADC D23 PF7 AREF AREF
    USB HOST PWR/MCU
    A5 AREF
    WiFi

    microSD Slot (on the bottom side)


    ON

    USB Host USB Power &


    CPU MIPS 24KEc 580MHz
    MCU USB Port
    MPU Reset Button Wi-Fi Reset Button RAM 128MB
    Flash 32 MB
    Wi-Fi Reset Button
    Wi-Fi 1T1R 802.11 b/g/n (2.4G)
    Ethernet 10/100Mbps
    SD SD-XC
    USB USB 2.0 Host
    MCU ATmega32U4 8MHz

    You might also like