Scribd Logo
Upload

Welcome to Scribd!

  • 134 views

    NPort 5100 Series QIG E4.0 PDF

    Uploaded by

    Anonymous HqwS65vtJ
    The document provides a quick installation guide for NPort 5100 series device servers. It includes an overview of the product, package contents checklist, hardware introduction and installation instructions, software installation information, pin assignments, and specifications. The guide is intended to help users get started with installation and set up of the NPort 5100 series device servers in a concise manner.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    NPort 5100 Series QIG E4.0 PDF

    Uploaded by

    Anonymous HqwS65vtJ
    134 views6 pages
    The document provides a quick installation guide for NPort 5100 series device servers. It includes an overview of the product, package contents checklist, hardware introduction and installation instructions, software installation information, pin assignments, and specifications. The guide is intended to help users get started with installation and set up of the NPort 5100 series device servers in a concise manner.

    Original Title

    NPort_5100_Series_QIG_e4.0.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides a quick installation guide for NPort 5100 series device servers. It includes an overview of the product, package contents checklist, hardware introduction and installation instructions, software installation information, pin assignments, and specifications. The guide is intended to help users get started with installation and set up of the NPort 5100 series device servers in a concise manner.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    134 views6 pages

    NPort 5100 Series QIG E4.0 PDF

    Uploaded by

    Anonymous HqwS65vtJ
    The document provides a quick installation guide for NPort 5100 series device servers. It includes an overview of the product, package contents checklist, hardware introduction and installation instructions, software installation information, pin assignments, and specifications. The guide is intended to help users get started with installation and set up of the NPort 5100 series device servers in a concise manner.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    NPort 5100 Series

    Quick Installation Guide

    Edition 4.0, November 2015

    Technical Support Contact Information


    www.moxa.com/support

    Moxa Americas: Moxa China (Shanghai office):


    Toll-free: 1-888-669-2872 Toll-free: 800-820-5036
    Tel: 1-714-528-6777 Tel: +86-21-5258-9955
    Fax: 1-714-528-6778 Fax: +86-21-5258-5505
    Moxa Europe: Moxa Asia-Pacific:
    Tel: +49-89-3 70 03 99-0 Tel: +886-2-8919-1230
    Fax: +49-89-3 70 03 99-99 Fax: +886-2-8919-1231
    Moxa India:
    Tel: +91-80-4172-9088
    Fax: +91-80-4132-1045

    2015 Moxa Inc. All rights reserved.

    P/N: 1802051000013
    *1802051000013*
    Overview
    NPort 5100 series device servers are compact, palm-sized data
    communication devices that allow you to control RS-232 (NPort 5110),
    RS-422/485 (NPort 5130), and RS-232/422/485 (NPort 5150) serial
    devices over a TCP/IP-based Ethernet.

    NOTE -T indicates an extended temperature model.

    Package Checklist
    Before installing the NPort 5100 series device server, verify that the
    package contains the following items:
    1 NPort 5100 series 1-port serial device server
    100 to 240 VAC power adapter (excluding T models)
    4 stick-on pads
    Documentation and software CD
    Quick Installation Guide
    Warranty card
    Optional Accessories
    DK-35A: DIN-Rail Mounting Kit (35 mm)
    Notify your sales representative if any of the above items are missing or
    damaged.

    -2-
    Hardware Introduction
    As shown in the following figures, NPort 5100 series device servers have
    one male DB9 port for transmitting RS-232 (NPort 5110), RS-422/485
    (NPort 5130), or RS-232/422/485 (NPort 5150) serial data.

    NOTE The NPort 5110, NPort 5130, and NPort 5150 have the same form
    factor.

    Reset ButtonPress the Reset button continuously for 5 sec to load


    factory defaults: Use a pointed object, such as a straightened paper clip
    or toothpick, to press the reset button. This will cause the Ready LED to
    blink on and off. The factory defaults will be loaded once the Ready LED
    stops blinking (after about 5 seconds). At this point, you should release
    the reset button.

    -3-
    LED IndicatorsNPort 5100s top panel has three LED indicators, which
    are described in the following table.

    LED Name LED Color LED Function


    Steady on: Power is on and NPort is booting up.
    Red Blinking: Indicates an IP conflict, or DHCP or
    BOOTP server is not responding properly.
    Steady on: Power is on and NPort is functioning
    Ready
    normally.
    Green
    Blinking: The NPort has been located by NPort
    Administrators Location function
    Off Power is off, or power error condition exists.
    Orange 10 Mbps Ethernet connection.
    Link Green 100 Mbps Ethernet connection.
    Off Ethernet cable is disconnected, or has a short.
    Orange Serial port is receiving data.
    Green Serial port is transmitting data.
    Tx/Rx
    No data is being transmitted or received through
    Off
    the serial port.

    Adjustable pull high/low resistor for RS-422/485 (150

    K or 1 K)

    Jumpers are used to set the pull high/low


    resistor values. The default is 150 K.
    Short the jumpers to set this value to 1
    K. Do not use the K setting with
    RS-232 mode, since doing so will degrade
    the RS-232 signals and shorten the
    communication distance.

    Hardware Installation Information


    STEP 1: After removing the NPort 5100 series device server from the box,
    connect the NPort 5100 series device server to a network. Use a standard
    straight-through Ethernet cable to connect to a hub or switch. When
    setting up or testing the NPort 5100 series device server, you might find
    it convenient to connect directly to your computers Ethernet port. In this
    case, use a cross-over Ethernet cable.
    STEP 2: Connect the NPort 5100 series device servers serial port to a
    serial device.
    STEP 3: Connect the power adaptor.
    STEP 4: Placement options

    -4-
    In addition to placing the Wall Mount DIN-Rail
    NPort 5100 on a desktop or
    other horizontal surface,
    you may also make use of
    the DIN-Rail or Wall Mount
    options, as illustrated here.

    Software Installation Information


    To install NPort Administration Suite, insert the NPort Document &
    Software CD into your computers CD-ROM drive. Once the NPort
    Installation CD window opens, click on the Installation button, and
    then follow the instructions on the screen.
    To view detailed information about NPort Administration Suite, click
    on the Documents button, and then select NPort 5100 Series Users
    Guide to open the pdf version of the users guide.

    Pin Assignments
    Ethernet Port Pinouts
    Pin No. Ethernet
    1 Tx+
    2 Tx-
    3 Rx+
    6 Rx-
    NPort 5110DB9 male (RS-232) port pinouts
    Pin No. RS-232
    1 DCD
    2 RxD
    3 TxD
    4 DTR
    5 GND
    6 DSR
    7 RTS
    8 CTS
    9
    NPort 5130DB9 male (RS-422/485) port pinouts
    Pin No. RS-422/485-4W RS-485-2W
    1 TXD-(A)
    2 TXD+(B)
    3 RXD+(B) Data+(B)
    4 RXD-(A) Data-(A)
    5 GND GND
    6
    7
    8
    9

    -5-
    NPort 5150DB9 male (RS-232/422/485) port pinouts
    Pin No. RS-232 RS-422/485-4W RS-485-2W
    1 DCD TXD-(A)
    2 RxD TXD+(B)
    3 TxD RXD+(B) Data+(B)
    4 DTR RXD-(A) Data-(A)
    5 GND GND GND
    6 DSR
    7 RTS
    8 CTS
    9

    Specifications
    Power Requirements
    Power Input 12 to 48 VDC
    Power Consumption NPort 5110: 128.7 mA @ 12V, 72 mA @ 24V
    NPort 5130: 200 mA @ 12V, 106 mA @ 24V
    NPort 5150: 200 mA @ 12V, 106 mA @ 24V
    Operating Temperature 0 to 55C (32 to 131F), for standard models
    -40 to 75C (-40 to 167F), for -T models
    Operating Humidity 5 to 95% RH
    Dimensions 75.2 x 80 x 22 mm including ears
    (2.96 x 3.15 x 0.87 in)
    52 x 80 x 22 mm without ears
    (2.05 x 3.15 x 0.89 in)
    Serial Line Protection 15 KV ESD for serial port
    Magnetic Isolation 1.5 KV for Ethernet
    Power Line Protection Level 2 Burst (EFT), EN61000-4-4
    Level 2 Surge, EN61000-4-5
    Regulatory Approvals FCC Class A, CE Class A, UL, LVD

    -6-

    You might also like