Condensing Cooling Systems PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 8
At a glance
Powered by AI
The document discusses heat rejection equipment like condensers and cooling towers and how they are used in HVAC systems.

Condensers are heat exchangers that remove heat from the refrigerant and transfer it to another medium like air or water. They desuperheat, condense and subcool the refrigerant.

The total heat of rejection is affected by the refrigeration effect, heat of compression, compressor efficiency and the condenser cooling method. Higher compressor pressures result in lower refrigeration effect and higher heat of compression.

COMMERCIAL

HVAC EQUIPMENT

Condensers
and Cooling
Towers
Technical Development Programs (TDP) are modules of technical training on HVAC theory,
system design, equipment selection and application topics. They are targeted at engineers and
designers who wish to develop their knowledge in this field to effectively design, specify, sell or
apply HVAC equipment in commercial applications.
Although TDP topics have been developed as stand-alone modules, there are logical group-
ings of topics. The modules within each group begin at an introductory level and progress to
advanced levels. The breadth of this offering allows for customization into a complete HVAC
curriculum from a complete HVAC design course at an introductory-level or to an advanced-
level design course. Advanced-level modules assume prerequisite knowledge and do not review
basic concepts.

This TDP module discusses the most common heat rejection equipment: condensers and
cooling towers. Heat rejection is a process that is an integral part of the air conditioning cycle.
The heat is rejected to the environment using air or water as the medium. In order to properly ap-
ply system concepts to a design, HVAC designers must be aware of the different heat rejection
methods. Also presented is the concept of total heat of rejection, its derivation, and how it ap-
plies to the process of air conditioning, as well as the controls that are used to regulate each type
of heat rejection unit.

2005 Carrier Corporation. All rights reserved.


The information in this manual is offered as a general guide for the use of industry and consulting engineers in designing systems.
Judgment is required for application of this information to specific installations and design applications. Carrier is not responsible for
any uses made of this information and assumes no responsibility for the performance or desirability of any resulting system design.
The information in this publication is subject to change without notice. No part of this publication may be reproduced or transmitted in
any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Carrier Corporation.

Printed in Syracuse, NY
CARRIER CORPORATION
Carrier Parkway
Syracuse, NY 13221, U.S.A.
Table of Contents
Introduction ..................................................................................................................................... 1
Condenser Total Heat of Rejection.................................................................................................. 2
Heat Rejection Factors................................................................................................................. 3
Condensers....................................................................................................................................... 4
Water-Cooled Condensers ........................................................................................................... 5
Once-Thru versus Recirculating .............................................................................................. 5
Water Requirement Calculation for Recirculating Systems .................................................... 6
ARI Conditions ........................................................................................................................ 7
Water Consumption and Makeup Quantity ............................................................................. 8
Construction and Types of Water-Cooled Condensers............................................................ 8
Fouling Factors ...................................................................................................................... 13
Tubing Materials.................................................................................................................... 15
Effects of Antifreeze .............................................................................................................. 15
Condenser Pass Arrangements............................................................................................... 16
Selection Inputs...................................................................................................................... 17
Air-Cooled Condensers.............................................................................................................. 17
Air-Cooled Condenser versus Air-Cooled Condensing Unit................................................. 18
Subcooling Circuit ................................................................................................................. 19
Placement............................................................................................................................... 20
Selection................................................................................................................................. 21
Evaporative Condensers............................................................................................................. 22
Evaporative Condenser Selection Parameters........................................................................ 24
Condenser Economics................................................................................................................ 25
Cooling Towers ............................................................................................................................. 27
Basic Terms ............................................................................................................................... 28
Entering Wet Bulb Temperature ............................................................................................ 28
Approach................................................................................................................................ 28
Range ..................................................................................................................................... 29
Total Heat of Rejection.......................................................................................................... 30
Drift (Windage)...................................................................................................................... 30
Evaporation............................................................................................................................ 31
Blow-down (Bleed)................................................................................................................ 31
Makeup .................................................................................................................................. 32
Cooling Tower Psychrometric Plot........................................................................................ 32
Types of Cooling Towers........................................................................................................... 33
Natural Draft (Atmospheric).................................................................................................. 33
Mechanical Draft ................................................................................................................... 34
Closed-Circuit Cooling Towers (Fluid Coolers).................................................................... 36
Application of Cooling Towers ................................................................................................. 37
Placement............................................................................................................................... 37
Effects of Reduced Cooling Tower Water Temperature........................................................ 38
Hydronic Free Cooling .......................................................................................................... 39
Cooling Tower Relief Profiles ............................................................................................... 40
Cooling Tower Differences: Electric versus Absorption Chillers ........................................ 41
Cooling Tower Selection ....................................................................................................... 43
Water Treatment ............................................................................................................................ 44
Condenser and Cooling Tower Control Systems........................................................................... 46
Water-Cooled Condensers .........................................................................................................47
Air-Cooled Condensers..............................................................................................................47
Refrigerant Side Control ........................................................................................................48
Airside Control.......................................................................................................................48
Evaporative Condensers.............................................................................................................50
Cooling Towers..........................................................................................................................51
Water Bypass of the Cooling Tower......................................................................................51
Airflow Control on Cooling Towers ......................................................................................52
Winter Operation of Cooling Towers ....................................................................................53
Summary........................................................................................................................................ 54
Work Session ................................................................................................................................. 55
Appendix........................................................................................................................................ 57
References:.................................................................................................................................57
Work Session Answers ..............................................................................................................58
CONDENSERS AND COOLING TOWERS

Introduction
Condensers and cooling towers are the most common kinds of heat rejection equipment.
There are three types of condensers: water-cooled, air-cooled, and evaporative. Water-cooled and
air-cooled condensers use a
sensible-only cooling proc-
ess to reject heat.
Evaporative condensers use
both sensible and latent heat
principles to reject heat.
Cooling towers are simi-
lar to evaporative condensers
because they also utilize la-
tent cooling through the
process of evaporation. We
will discuss three kinds of
cooling towers in this TDP: Figure 1
natural, mechanical, and Three Types of Condensers
closed-circuit. Photos: Water-cooled: Courtesy of Standard Refrigeration; Evaporative: Courtesy of
Baltimore Aircoil Company
We will discuss total
heat of rejection, its deriva-
tion, and how it applies to
the process of air condition-
ing. Applications for
condensers and cooling tow-
ers, as well as the controls
that may be used to maintain
proper refrigerant and water
temperatures will also be
covered.

Figure 2
Cooling Towers
Photos reproduced with permission of Baltimore Aircoil Company

Commercial HVAC Equipment


1
CONDENSERS AND COOLING TOWERS

Condenser Total Heat of Rejection


The heat to be rejected by the condenser in condensing the refrigerant is equal to the sum of
the refrigeration effect (RE) of the evaporator plus the heat equivalent of the work of the com-
pression.
RE + Compressor work = THR (Total Heat Rejection)
Heat rejection in the condenser
may be illustrated on the P-H (pres-
sure-enthalpy) diagram. A pressure-
enthalpy diagram is used because
condensing takes place at constant
pressure, or nearly constant pressure
when blended refrigerants are used,
(line F-G). This diagram may also be
used to show the pressure rise of the
condensing medium as it absorbs heat
from the refrigerant (curved line).
The THR of the condenser is de-
fined by line E-H, which is the sum of
the refrigeration effect (line A-B) and
the heat of compression (line C-D). Figure 3
As the ratio between compressor dis- Condenser Total Heat of Rejection (shown on p-h diagram)
charge and suction pressures increase,
the refrigeration effect decreases and
the heat of compression increases. This is because the work done by the compressor has in-
creased.
These are the equations to calculate the THR in units of Btuh:
In cases where the brake horsepower (bhp) of the compressor(s) is known:
THR = RE + (bhp 2545)

2545 is a constant; it is the Btuh


equivalent of one bhp. Brake horse-
power is the application rating for the
compressor.
In cases where the compressor
kW is known:
THR = RE + (kW 3414)
3414 Btuh is equivalent to one
kW.
Figure 4
Total Heat of Rejection Formulas

Commercial HVAC Equipment


2
CONDENSERS AND COOLING TOWERS

THR reflects the work done by the compressor as


Kilowatts well as the evaporator. THR can be expressed in Btuh
(1000 watts) is the term used to tons, or MBtuh. One MBtuh is equal to 1000 Btuh.
describe compressor power. The Where refrigerant is used to cool the motor, such as in a
kW unit is used more often than hermetic-type compressor design, added heat (the heat
brake horsepower because most from the motor losses) also becomes part of the THR in
manufacturers product ratings the condenser.
are now expressed in kW.

Heat Rejection Factors


Heat rejection factor is a multiplier applied to the cool-
ing capacity to find the condenser total heat of rejection. When a chiller
The amount of heat added to the cooling capacity to is said to have a 100-ton
arrive at the THR for any given application is a function of capacity we are referring to the
the compressor efficiency and the condenser cooling refrigeration effect. The
method (air, water, or evaporative) cooled. As an example, condenser, however, should be
represented in terms of THR
compressors used in HVAC equipment typically have a
tons. In the case of an air-cooled
full load heat rejection factor in the range of 1.15 to 1.25. chiller, for example, the THR
Water-cooled screw and centrifugal compressors are would be approximately 1.25
very efficient, so they tend to have heat rejection factors 100 = 125 tons.
between 1.15 and 1.18. Compressors used in air-cooled
applications typically have heat rejection factors closer to 1.25. This efficiency is a function of
the saturated condensing temperature, which is lower for water-cooled chiller compressors.
Using a value of 1.17 as an example for a water-cooled chiller, for every ton (12,000 Btuh)
refrigeration effect, the load on the water-cooled condenser would be:
12,000 1.17 = 14,040 Btuh heat rejection for each ton of cooling capacity
A heat rejection factor of
1.25 results in 15,000 Btuh
heat rejection per ton of cool-
ing. (12,000 1.25 = 15,000).
Consequently, 15,000 Btuh per
cooling ton was used for many
years as representative of all
chillers. For modern water-
cooled chillers, however, this
value is no longer accurate due
to efficiency improvements.

Figure 5
Typical Heat Rejection Factors

Commercial HVAC Equipment


3
CONDENSERS AND COOLING TOWERS

Condensers
Condensers remove heat from the refrigeration system. Like the evaporator, the condenser is
a heat transfer device. Heat from the high-temperature, high-pressure refrigerant vapor is trans-
ferred to a heat-absorbing me-
dium (air or water) that passes
over or through the condenser.
Condensers do three things:
desuperheat the refrigerant
gas, condense the hot refriger-
ant gas into a liquid, and
subcool the liquid refrigerant.

Figure 6
Condenser Definition

Condensers are one of the four basic refrigeration components. The other three are the evapo-
rator, compressor, and metering device. The metering device shown in Figure 7 is a thermostatic
expansion valve.

Figure 7
Condensers reject the heat from the evaporator and the compressor.

Commercial HVAC Equipment


4

You might also like