DICHTOMATIK O-RING HANDBOOK

O-RING GLAND DESIGN GUIDELINES

SECTION TWO
O-RING GLAND DESIGN GUIDELINES

O-Ring Seal Types

Gland Dimension Calculations

O-Ring Dimensions

Selecting an O-Ring Cross-Section

ID/OD Interference
Reduction in Cross-Section

Compression Squeeze and Compression Ratio

Gland Fill

Extrusion

Back-Up Rings

Additional Groove Details

Installation

2
 DICHTOMATIK O-RING HANDBOOK
O-RING GLAND DESIGN GUIDELINES

THE 0-RING DESIGN GUIDE

This o-ring gland design guide is intended for use in specifying o-ring and gland dimensions for static applications
with pressures up to 1500 PSI. For dynamic applications and for pressure greater than 1500 PSI, please contact
Dichtomatik North America.

The guidelines are for the nominal condition. The minimum and maximum stack-up conditions should also be checked.
This entails evaluating the seal design dimensionally with the largest possible o-ring in the smallest possible gland and
the smallest possible o-ring in the largest possible gland.

EXAMPLE: Consider an o-ring with a 1.780.08 mm cross-section and a radial o-ring gland with a 1.520.10 mm
height. The formula for compression ratio (which will be introduced in this guide) is as follows.

Compression Ratio Calculation

O-Ring CS Gland Height
Compression Ratio =
O-Ring CS x

The acceptable range is 5% to 30%.

Using the nominal values for the compression ratio yields the following result:

Compression ratio at nominal conditions:

1.78 mm 1.52 mm
= 14.6% compression
1.78 mm x

A compression ratio of 14.6% falls within the acceptable range, so based on the nominal measurements, the
design is good. Next we need to check the maximum and minimum conditions. The maximum compression ratio
occurs when the largest o-ring is in the smallest gland. This calculation is as follows:

Largest possible o-ring in smallest possible gland:

1.86 mm 1.42 mm
= 23.7% compression
1.86 mm x

We then check the minimum compression ratio which occurs with the smallest o-ring in the largest gland. This
calculation is as follows:

Smallest possible o-ring in largest possible gland:

1.70 mm 1.62 mm
= 4.7% compression
1.70 mm x

With this design the maximum compression ratio is 23.7% which is within the recommended range. However,
the minimum compression ratio is only 4.7% which is not within the acceptable range. In this situation, the design
should be modified to ensure that the minimum compression ratio is within the acceptable range or testing should
be completed at this minimum condition to ensure that the seal will perform as required.

Throughout this reference guide the term compression is used to describe what happens to the o-ring. Since
elastomers are essentially incompressible, the technically correct term would be deformation. Compression is used
as the more common terminology in the sealing industry.

NOTE: It is critical to remember that most sealing applications are unique. Textbook guidelines regarding o-ring gland
design are no substitute for actually testing the components and the seals in their real-world conditions to determine
if the design is optimal and, more importantly, safe.

12
 DICHTOMATIK O-RING HANDBOOK

O-RING SEAL TYPES

Most static o-ring seals are one of the three types shown below. In the male gland seal the groove for the o-ring is
machined into the piston (the part that is inserted into the bore) and that part with the o-ring installed on it is inserted
into the bore. The o-ring seals radially. In the female gland seal the groove for the o-ring is machined into the bore
and a smooth rod is inserted through the installed o-ring. As with the male gland seal, the o-ring seals radially. For
the face seal, the groove is machined into the face that is perpendicular to the piston or rod. The o-ring seals axially.

The variable names presented in these diagrams are used throughout the design guide.

Male Gland Seal Female Gland Seal Face Seal

Width Width Height

Width

Bore Bore

Gland Piston Gland Rod Gland ID Gland OD

G L A N D D I M E N S I O N C A L C U L AT I O N S

Although each physical arrangement is different, each involves the o-ring being
Gland Dimensions
captured in a rectangular gland which has two sets of opposing surfaces.

1. The first set of opposing surfaces is sealing surfaces, in that the distance Height
between them, the gland height, is less than the o-ring cross-section (CS) so that
the installed o-ring is compressed resulting in a sealing force.

2. The second set of opposing surfaces is containing surfaces, in that the Width
distance between them, the gland width, is larger than the o-ring cross-section
Sealing
so that they only serve to keep the o-ring in place.
Surfaces
Gland height and width are used for compression and fill calculations. The
Containment
formulas for calculating these gland dimensions for male gland, female gland
Surfaces
and face seals are shown below.

Male Gland Seal Female Gland Seal Face Seal

Bore Gland Gland Rod Height = Height
Height = Height =
2 x 2 x Gland OD Gland ID
Width =
Width = Width Width = Width 2 x

13
 DICHTOMATIK O-RING HANDBOOK
O-RING GLAND DESIGN GUIDELINES

O-RING DIMENSIONS

Dimensionally specifying an o-ring is typically done with just two dimensions, the inner diameter (ID) and the cross-
section (CS). Occasionally, an o-ring may be specified with an outer diameter (OD) and cross-section or an inner
diameter and outer diameter. If two of the three dimensions are known, the third can be calculated using the formulas
shown below.

O-Ring Dimensions O-Ring Dimension Calculations

OD = ID + (2 x CS)
ID = OD (2 x CS)
OD ID
CS =
OD ID CS 2 x
A A

Section A-A

SELECTING AN O-RING CROSS SECTION

Whereas the ID or OD of the o-ring for a design is significantly influenced by the diameter of the mating components
(piston/rod and bore), the cross-section of the o-ring is usually fairly arbitrary. The following table describes some of
the advantages when opting for a small cross-section or a large cross-section.

Advantages of Smaller Cross-Section Advantages of Larger Cross-Section

More compact. Less prone to compression set.

Lighter weight. Less volume swell in liquidon percentage
Less expensive especially for higher cost basis.
elastomers like FKM or fluorosilicone. Allows for larger tolerances while still main-
Less machining required for machined grooves taining acceptable compression squeeze and
since grooves are smaller. compression ratio over full stack-up range.

More resistant to explosive decompression. Less prone to leakage due to contamination

dirt, lint, scratches, etc.

ID/OD INTERFERENCE

The ID or OD of the o-ring should be chosen to minimize the potential for installation damage and to minimize wear
during use. This can be accomplished by adhering to the following guidelines.

For male gland seals the ID of the o-ring should be smaller than the OD of the gland so that the installed o-ring
is always slightly stretched. As with all o-ring design calculations, this should be checked at the maximum and
minimum stack-up conditions.

For female gland seals the OD of the o-ring should be slightly larger than the ID of the gland so there is always
some interference.

continued next page

14
 DICHTOMATIK O-RING HANDBOOK

ID/OD INTERFERENCE continued

For external pressure face seals the ID of the o-ring should be slightly smaller than the gland inner diameter
(Gland ID) so when the pressure is applied, the o-ring is already where it would be as a result of the pressure.

For internal pressure face seals the OD of the o-ring should be slightly larger than the gland outer diameter (Gland
OD) so when the pressure is applied, the o-ring is already where it would be as a result of the pressure.

Male Gland Seal External Pressure Face Seal

Gland ID Gland ID ID
Interference = Interference =
ID x ID x
Maximum = 5% Minimum = 0% Maximum = 5% Minimum = 0%

Female Gland Seal Internal Pressure Face Seal

OD Gland OD Gland OD
Interference = Interference =
OD x OD x
Maximum = 2% Minimum = 0% Maximum = 3% Minimum = 0%

REDUCTION IN CROSS-SECTION

Since elastomers are essentially incompressible materials, if the ID of the o-ring is stretched (as a result of ID interfer-
ence), the cross-section of the o-ring will decrease. The following tables give the o-ring cross-sections that result from
ID interference. The new cross-section should be used for all compression and gland fill calculations.

The impact of OD interference on the o-ring cross-section varies and does not require design considerations.

For reference purposes the equation for the volume of an o-ring is as follows.

O-Ring Volume

Volume =
2 x CS 2 x [ID + CS]
4x

AS568 Original Cross-Section Reduced Cross-Section at

Series in Inches % ID Interference (inches)

1% 2% 3% 4% 5%

- 0XX* 0.070 in. .069 .069 .068 .068 .068

-1XX 0.103 in. .102 .101 .100 .100 .100

-2XX 0.139 in. .138 .137 .136 .135 .134

-3XX 0.210 in. .208 .206 .205 .204 .203

-4XX 0.275 in. .272 .270 .268 .267 .266

*Except for -001, -002 and -003 sizes.

continued next page

15
 DICHTOMATIK O-RING HANDBOOK
O-RING GLAND DESIGN GUIDELINES

REDUCTION IN CROSS-SECTION continued

AS568 Original Cross-Section Reduced Cross-Section at

Series in Millimeters % ID Interference (mm)

1% 2% 3% 4% 5%

-0XX* 1.78 mm 1.76 1.75 1.74 1.73 1.72

-1XX 2.62 mm 2.59 2.57 2.56 2.55 2.53

-2XX 3.53 mm 3.49 3.47 3.44 3.43 3.41

-3XX 5.33 mm 5.28 5.24 5.20 5.18 5.15

-4XX 6.99 mm 6.92 6.87 6.82 6.79 6.75

*Except for -001, -002 and -003 sizes.

COMPRESSION SQUEEZE & COMPRESSION RATIO

An elastomer is defined as a synthetic or natural material with resilience or memory sufficient to return to its original
shape after a major or minor distortion. This resilience of elastomers is what makes o-rings work as seals. The design
parameters that ensure this resilience is properly used and will probably have the biggest impact on o-ring sealing
performance are compression squeeze and compression ratio.

Compression squeeze is the difference between the original o-ring cross-section (CS) and the gland height (Height)
and is expressed in either inches or millimeters. Since almost all elastomers quickly take a 100% compression set with
very light squeeze, it is essential that a minimum compression squeeze of 0.1mm (0.005 inches) be maintained.

Compression Squeeze Calculation

Compression Squeeze = CS* Height
Compression Squeeze

Recommended Minimum Value

CS Height Compression Squeeze > 0.1 mm (0.005 in)

* Note: Be sure to use the reduced cross-section in

this calculation.

Compression ratio expresses what percentage the compression squeeze is of the uncompressed o-ring cross-section.

Compression Ratio Calculation

Compression Squeeze Compression Squeeze
Compression Ratio = x 100
CS x
X%
Recommended Value
100% See Table

continued next page

16
 DICHTOMATIK O-RING HANDBOOK

COMPRESSION SQUEEZE & RATIO c o n t i n u e d

The compression ratio recommendations are for static sealing applications. Most dynamic sealing applications would
use tighter tolerances on the mating components and then target a compression ratio range in the lower half of the
static sealing recommended range (5% to 20%). The lighter compression squeeze is recommended due to friction and
wear considerations.

Male or Female Gland Seal Face Seal

Minimum 5% Target 20% Maximum 30% Minimum 10% Target 25% Maximum 35%

GLAND FILL

Gland fill is the percentage of the gland that is occupied by the o-ring. It is calculated by dividing the cross-sectional
area of the o-ring by the cross-sectional area of the gland.
Calculations

O-Ring Cross-Sectional Area Gland Cross-Sectional Area Gland Fill

O-Ring CSA
Gland Fill (%) = x 100
Gland CSAx
CS Height

Width
2
CS
O-Ring CSA = x Gland CSA = Height x Width
2x

The following target gland fill recommendations take into account several hardware and o-ring related factors including
but not limited to thermal expansion, volume swell due to fluid exposure and the effect of tolerance stack-ups.

Recommended Values

Minimum 50% Target Minimum 65% Target 75% Target Maximum 85% Maximum 90%

EXTRUSION GAP

Extrusion is a concern for radial seals where there is a gap between the piston and the bore for a male gland seal
or between the rod and the bore for a female gland seal. Extrusion is not a concern for face seals where the metal
parts to be sealed are typically in line-to-line contact. The concern is that at higher pressures, especially for softer
o-ring elastomers, the o-ring can be forced by the pressure into the small gap between the piston or rod and the bore.
Unless the bore and the piston or rod are ensured to remain concentric by the hardware, we have to assume that all
of the gap possible can shift to one side (see diagram next page).

continued next page

17
 DICHTOMATIK O-RING HANDBOOK
O-RING GLAND DESIGN GUIDELINES

EXTRUSION GAP continued

Male Gland Seal Female Gland Seal

Extrusion Gap = Bore Piston Extrusion Gap = Bore Rod

Extrusion Concentricity & Diametric Clearance

The following table indicates the maximum

recommended total diametric clearance for
a given system pressure and elastomer
hardness. For pressures or hardness values
between those listed in the table, either
interpolate to determine the value or use the
next higher pressure and the next lower
durometer.

Pressure Elastomer Hardness (Durometer)

PSI 60 70 80 90
500 .010" (.25 mm) .015" (.38 mm) .020" (.51mm) .025" (.64 mm)

750 .005" (.13 mm) .011" (.28 mm) .016" (.41mm) .023" (.58 mm)

1000 .002" (.05 mm) .008" (.20 mm) .012" (.30 mm) .018" (.46 mm)

1250 .001" (.02 mm) .004" (.10 mm) .009" (.23 mm) .015" (.38 mm)

1500 Consult Dichtomatik .002" (.05 mm) .007" (.18 mm) .012" (.30 mm)

BACK-UP RINGS

Back-up rings are used to prevent o-rings from extruding when the tight
Use of a Back-up Ring
tolerances listed in the previous section cannot be maintained. Back-
up rings do not provide any sealing function. They are simply intended
to reduce the extrusion gap on the low-pressure side so that the o-ring
can fulfill its sealing function without being damaged.

Back-up rings are made of materials with better extrusion resistance

than most elastomers. Several common materials are high-durometer
NBR (or other elastomers), Nylon and filled PTFE.

continued next page

18
 DICHTOMATIK O-RING HANDBOOK

BACK-UP RINGS continued

Since the materials used for back-up rings are basically non-
Accommodating the Back-Up Ring
compressible and non-deformable, they can typically be treated as
though they are part of whatever the o-ring groove is machined into.
That is, the width of the groove has to be increased just enough to
accommodate the thickness of the back-up ring. Area for o-ring

For back-up rings with a curved surface facing the o-ring, the effective
thickness of the back-up ring can be determined by dividing the cross-
sectional area of the back-up ring by the height of the back-up ring.
This ensures that the o-ring has the same area to occupy.
Area for o-ring

Back-up ring thickness

A D D I T I O N A L G R O O V E D E TA I L S

Once the geometric arrangement and dimensions for the o-ring gland have been determined, the following details
must be observed for correct sealing function.

Groove Wall Angle

The wall angle of the groove should be controlled to be between Wall Angle
0 and 5 as shown.

Wall Angle

Transition Radii
The transition from the piston, bore, or face to the groove edge and Transition Radii
from the groove edge to the groove bottom must be slightly rounded
as shown. Radii recommendations follow on the next page.

Radius 1

Radius 2

continued next page

19
 DICHTOMATIK O-RING HANDBOOK
O-RING GLAND DESIGN GUIDELINES

A D D I T I O N A L G R O O V E D E TA I L S c o n t i n u e d

Transition Radii

TRANSITION RADII
Cross Section range Radius 1 Radius 2
mm 1.0 2.0 0.10 0.30
inch 0.04 0.08 0.004 0.012
mm 2.0 3.0 0.20 0.30
inch 0.08 0.12 0.008 0.012
mm 3.0 4.0 0.20 0.50
inch 0.12 0.16 0.008 0.020
mm 4.0 5.0 0.20 0.60
inch 0.16 0.20 0.008 0.024
mm 5.0 6.0 0.20 0.60
inch 0.20 0.24 0.008 0.024
mm 6.0 8.0 0.20 0.80
inch 0.24 0.31 0.008 0.031
mm 8.0 10.0 0.20 1.00
inch 0.31 0.39 0.008 0.039
mm 10.0 12.0 0.20 1.00
inch 0.39 0.47 0.008 0.039
mm 12.0 15.0 0.20 1.20
inch 0.47 0.59 0.008 0.047

Surface Finish
The surface finish of the sealing surfaces and the sides of the gland Sealing Surface Finish
should be controlled as shown.
Sealing Surface A

Containing Surfaces

Sealing Surface B

continued next page

20
 DICHTOMATIK O-RING HANDBOOK

A D D I T I O N A L G R O O V E D E TA I L S c o n t i n u e d

Surface Finish

Surface Finish Acceptable Range for CONSTANT PRESSURE Applications

Max Ra Max Rz Max Rmax

Sealing Surface A m 1.6 6.3 10.0

inch 64 256 400
Sealing Surface B m 3.2 10.0 12.5
inch 128 400 500
Containing Surfaces m 6.3 12.5 16.0
inch 256 500 640

Surface Finish Acceptable Range for PULSATING PRESSURE Applications

Max Ra Max Rz Max Rmax

Sealing Surface A m 0.8 1.6 3.2

inch 32 64 128
Sealing Surface B m 1.6 3.2 6.3
inch 64 128 252
Containing Surfaces m 3.2 6.3 10.0
inch 128 252 400

I N S TA L L AT I O N

Installation Chamfer
A perfectly designed o-ring seal is of little use if the o-ring is damaged Installation Chamfer Length
during installation. To prevent damage for male gland and female gland
seals, a 15 chamfer on the bore or rod is recommended. The chamfer must
be long enough to ensure that the o-ring sees only the chamfer when it is
installed. Face seals do not require installation chamfers.

O-Ring CS Chamfer Length

Inches mm Inches mm
.070 1.78 .083 2.10

.103 2.62 .122 3.10

.139 3.53 .157 4.00

.210 5.33 .236 6.00

.275 6.99 .283 7.20

continued next page

21
 DICHTOMATIK O-RING HANDBOOK
O-RING GLAND DESIGN GUIDELINES

I N S TA L L AT I O N continued

General Installation Guidelines

The following general guidelines should be observed for installation of an o-ring to avoid damage and leakage.

The o-ring must not be stretched beyond its elongation limit.

Edges must be burr-free and all radii and angles should be applied smoothly.

Dust, dirt, metal chips and other foreign material should be removed prior to installation of the o-ring.

Tips of screws and installation housings for other sealing and guiding elements should be covered by an
assembly sleeve.

A suitable lubricant should be applied to the assembly surfaces and/or the o-ring.

All installation tools (mandrels, sleeves, etc.) should be made of a soft material and not have any sharp edges.

The o-ring should not be rolled over assembly surfaces.

Ensure that the o-ring is not twisted during installation into the groove.

22