Chemical Engineering Draft

CURRICULUM
OF
CHEMICAL ENGINEERING
BE, BSc
&
ME, MSc
(Revised 2016)
EDUC ATION
HIGHER EDUCATION COMMISSION

ISLAMABAD
1
CURRICULUM DIVISION, HEC
Prof. Dr. Mukhtar Ahmed Chairman, HEC
Mr. Fida Hussain Director General (Acad)
Ms. Ghayyur Fatima Director (Curri)
Mr. Rizwan Shoukat Deputy Director (Curri)
Mr. Abid Wahab Assistant Director (Curri)
Mr. Riaz-ul-Haque Assistant Director (Curri)
Composed by: Mr. Zulfiqar Ali, HEC, Islamabad
2
Table of Contents
1. Minutes 6
2. Rationale 9
3. Mission Statement 10
4. Objectives 10
5. Framework for
BE, BSc in Chemical Engineering 11
6. Scheme of Studies for BE, BSc in Chemical 15

Engineering
7. Detail of Courses for BE, BSc in

Chemical Engineering 17
8. Social Sciences and Management Courses 67

9. Framework for ME, MSc in Chemical 82
Engineering
10. Detail of Courses for ME, MSc 84
11. Recommendations 93
3
PREFACE
The curriculum, with varying definitions, is said to be a plan of the teaching-
learning process that students of an academic programme are required to
undergo. It includes objectives & learning outcomes, course contents, scheme
of studies, teaching methodologies and methods of assessment of learning.
Since knowledge in all disciplines and fields is expanding at a fast pace and
new disciplines are also emerging; it is imperative that curricula be developed
and revised accordingly.
University Grants Commission (UGC) was designated as the competent

authority to develop, review and revise curricula beyond Class-XII vide Section
3, Sub-Section 2 (ii), Act of Parliament No. X of 1976 titled Supervision of
Curricula and Textbooks and Maintenance of Standard of Education. With the
repeal of UGC Act, the same function was assigned to the Higher Education
Commission (HEC) under its Ordinance of 2002, Section 10, Sub-Section 1
(v).
In compliance with the above provisions, the Curriculum Division of HEC

undertakes the revision of curricula after every three years through respective
National Curriculum Revision Committees (NCRCs) which consist of eminent
professors and researchers of relevant fields from public and private sector
universities, R&D organizations, councils, industry and civil society by seeking
nominations from their organizations.
In order to impart quality education which is at par with international standards,

HEC NCRCs have developed unified templates as guidelines for the
development and revision of curricula in the disciplines of Basic Sciences,
Applied Sciences, Social Sciences, Agriculture and Engineering in 2007 and
2009.
It is hoped that this curriculum document, prepared by the respective NCRCs,

would serve the purpose of meeting our national, social and economic needs,
and it would also provide the level of competency specified in Pakistan
Qualification Framework to make it compatible with international educational
standards. The curriculum is also placed on the website of HEC
http://hec.gov.pk/english/services/universities/RevisedCurricula/Pages/default.aspx
(Fida Hussain)
Director General (Academics)
4
CURRICULUM DEVELOPMENT PROCESS
STAGE-I STAGE-II STAGE-III STAGE-IV
CURRI. UNDER CURRI. IN DRAFT FINAL STAGE FOLLOW UP

CONSIDERATION STAGE STUDY
COLLECTION OF APPRAISAL OF 1ST PREP. OF FINAL QUESTIONNAIRE

DRAFT BY EXP. OF
REC CURRI.
COL./UNIV
CONS. OF CRC. FINALIZATION OF INCORPORATION OF COMMENTS

DRAFT BY CRC REC. OF V.C.C.
PREP. OF DRAFT APPROVAL OF PRINTING OF REVIEW

BY CRC CURRI.BY V.C.C. CURRI.
Abbreviations Used: IMPLE.OF CURRI. BACK TO STAGE-I

CRC. Curriculum Revision
Committee
VCC. Vice Chancellors Committee
EXP. Experts
COL. Colleges
UNI. Universities
ORIENTATION
PREP. Preparation COURSES
REC. Recommendations
5
MINUTES OF THE FINAL MEETING
The final meeting of National Curriculum Revision Committee (NCRC) in the

discipline of Chemical Engineering was held from March 14-16, 2016 at HEC
Regional Centre, Lahore to revise and prepare final draft curriculum for BE,
BSc & ME, MSc levels of Chemical Engineering. The following members
attended the meeting:-
Sr. Name & Address Status

No.
1. Prof. Dr. Javaid Rabbani Khan, Convener
Professor,
Department of Chemical Engineering,
GIK University of Engineering Science & Technology,
Topi, KP.
2. Prof. Dr. Muhammad Tayyeb Javed, Member
Head of Department,
Pakistan Institute of Engineering and Applied Sciences,
C-209, P.O. Nilore, Islamabad.
3. Dr. Arshad Chugtai, Member
Visiting Faculty,
School of Chemical & Materials Engineering (SCME),
National University of Sciences & Technology,
Sector H-12, Islamabad.
4. Dr. Muhammad Mazhar Iqbal, Member
Director,
Project Management Organization NESCOM,
Opposite EME College, Peshawar Road, Golra More,
Rawalpindi.
5. Prof. Dr. Amir Ijaz, Member
Director.
Institute of Chemical Engineering & Technology,
New Campus,
University of Punjab, Lahore.
6. Dr. Muhammad Jamil, Member
HoD,
University of Faisalabad, Amin Campus, West Canal
Road, Faisalabad.
7. Dr. Ghulam Mustafa Mamoor, Member
Professor,
Wah Engineering College,
University of Wah, Wah Cantt.
6
8. Dr. Fahad Rehman, Member
Assistant Professor,
COMSATS Institute of Information Technology, Defence
Road, Off Raiwind Road, Lahore.
9. Prof. Dr. M. Suleman Tahir, Member
Professor,
University of Gujrat, Engineering Block, Hafiz Hayat
Campus, Gujrat.
10. Dr. Inayatullah Memon, Member
Professor & Chairman,
NED University of Engineering &Technology, Main
University Road, Karachi.
11. Mr. Abdul Waheed Bhutto Member
Department of Chemical Engineering, Dawood University
of Engineering & Technology,
M.A Jinnah Road, Karachi.
12. Dr. Shaheen Aziz Shaikh, Member
Professor,
Mehran University of Engineering & Technology,
Jamshoro.
13. Dr. Shagufta Ishtiaque, Member
Assistant Professor/In-Charge,
University of Karachi, Karachi.
14. Dr. Muhammad Najam Khan, Member
Associate Professor / Chairperson,
Department of Chemical Engineering, Balochistan
University of Information Technology, Engineering &
Management Science, Takatu Campus, Airport Road,
Balili, Quetta.
15. Prof. Dr. Muhammad Zafar Noon, Member
Campus Coordinator,
Department of Chemical, Polymer Engineering,
University of Engineering & Technology, KSK Campus,
Lahore.
16. Prof. Dr. Shahid Raza Malik, Member
Director / CEO,
NFC Institute of Engineering & Fertilizer Research,
Jaranwala Road, Faisalabad.
7
17. Dr. Muhammad Asim Ibrahim, Member
Pakistan Institute of Engineering & Applied Sciences, C-
209, P.O. Nilore, Islamabad.
18. Dr. Saeed Gul, (Secretary) Secretary
Associate Professor,
University of Engineering & Technology, University
Campus, Peshawar.
The meeting started with recitation of Verses from the Holy Quran by Mr.
Rizwan Shoukat, Deputy Director HEC, and he welcomed the participants of
the meeting on behalf of the Chairman HEC. He thanked the members of the
committee and their institutions for their efforts and their quality contribution in
the preparation of the curriculum. He also thanked the Convener, Prof. Dr.
Javaid Rabbani Khan, for taking personal interest in the development of the
curriculum and for excellent coordination of the efforts of the committee.
At the beginning of the regular agenda, the Convener and Secretary discussed
the curriculum prepared by the members in the first meeting and thanked the
members for providing additional information for the curriculum after the first
meeting.
The committee also visited the Chemical Engineering Department of the
University of the Punjab. All members of the committee appreciated the efforts
and hospitality of Prof. Dr. Amir Ijaz Director Institute of Chemical Engineering
& Technology (ICET) for arranging the visit of ICET postgraduate and
undergraduate labs and interactive meeting with the faculty members.
The Convener, Prof. Dr. Javaid Rabbani Khan, closed the meeting with thanks
on behalf of all committee members to HEC for its efforts on the advancement
of higher education and for providing a platform at the national level to bring
together the experts from various institutions to develop the electronic
engineering curriculum. He thanked all members of the committee for their
dedication, hard work, and excellent teamwork in the preparation of the revised
curriculum. He requested the members of the committee to convey his thanks
to their respective institutions for support of this task of national importance.
Finally, he thanked Mr. Nazeer Hussain and the staff of the HEC Regional
Centre, Lahore, for their dedicated support of the committee and generous
hospitality.
RATIONALE:
The chemical engineering curriculum is designed so that its graduates are
familiar with the techniques used in analyzing and solving engineering
problems associated with the chemical and related industries (petroleum,
pharmaceutical, metallurgical, plastics, pollution control etc.).
8
Chemical engineering is the application of mathematical and Natural
Sciences by processing the raw material to finished product, economically
without polluting environment for the benefit of mankind. Chemical
engineering also applies the principles and application of other fields to
improve and solve the problems of chemical engineering processes
encountered in industries.
The chemical engineering curriculum is so designed that it not only includes

the core chemical engineering courses but also courses from basic sciences
(mathematics, chemistry, physics), communication skills, Islamiat and
Pakistan studies, so that the graduate will not only have professional skills
but also have a knowledge and understanding of basic principles, ethical
considerations and leadership qualities.
Courses in chemical engineering fundamentals (material and energy

balances) are introduced, followed by intensive work in engineering science
and analysis (heat, mass, and momentum transfer; chemical
thermodynamics; chemical reaction engineering; continuous and stage-wise
separation processes; process dynamics and control). Computer solutions
and simulation topics are stressed. An understanding of the ethical, and social
issues, economic, and safety considerations in engineering practice is
stressed throughout the curriculum. The appreciation of these professional
concepts is incorporated as a part of all engineering course work.
MISSION STATEMENT:
Mission of chemical engineering undergraduate program is to provide

qualified manpower with inter-disciplinary academic foundations needed to
develop chemical products for the society. The program is aligned to integrate
critical thinking, scholarly training, leadership qualities and sustainable vision
in graduates to enable them to cope with the complex problems of the chemical
and allied industries.
OBJECTIVES:
This curriculum is designed to impart knowledge, skills and training in
order to prepare graduates to have:
Understanding of the needs of the society and demands of the

21stcentury and be able to improve quality of life
Understanding of the principles of chemical engineering design and
their application for sustainable development
Ability to understand, analyze, interpret and solve problems of chemical
and allied industries by using modern techniques, engineering tools,
research and innovation
Understanding of safety principles and practices in process industries
Understanding of professional and ethical responsibilities
9
Knowledge of contemporary issues and ability to work in
multidisciplinary teams
Leadership skills to serve on managerial positions within chemical
and associated industries
Understanding of life cycle environmental impacts of chemical and
allied industries and their mitigation measures
Effective communication of technical knowledge, skills and training
Motivation to maintain and raise their level of engineering competence
and achievement by engaging in lifelong learning
10
ELIGIBILITY CRITERIA BE, BE in CHEMICAL ENGINEERING:
The eligibility criteria for admission to undergraduate degree in Chemical
Engineering as prescribed by the Pakistan Engineering Council (PEC) is
endorsed.
Framework BE, BSc Chemical Engineering
Non-Engineering Domain
Knowledge Subject Name of Course Th Lab C. Total Total % % overall
Hrs Courses Credits Area
Area Area
Functional English 3 0 3
Communication 0 1 1
Skills 3 6 15 5.2
English
Technical Report
writing & 2 0 2
Humanities Presentation skills
Pakistan Studies 1 0 1
Culture Islamic 2 3 7.5 2.2
Studies/Ethics 2 0 2
Social Sciences-I 2 0 2
*Social Social Sciences-II 2 4 10 3.0
Sciences (Chemical 2 0 2
Engineering
Economics) 2 0 2
Industrial
Management
Management Manage
sciences ment 2 4 10 3.0
sciences Entrepreneurship 2 0 2
Physics Applied Physics 3 1 4 1 4 10 3.0
Maths-I (Calculus
& Analytical 3 0 3
Geometry)
Maths-II (Applied
Natural Mathematics) 3 0 3
Sciences Mathematics 4 11 27.5 7.5
Maths-III
(Chemical 3 0 3
Engineering
Mathematics)
Probability &
Statistics 2 0 2
Inorganic & 3 1 4
Organic
Chemistry 2 8 20 6.0
Chemistry Physical & 3 1 4

Analytical
TOTAL 16 40 100 30
Chemistry
11
Engineering Domain
Knowledge Subject Area Name of Course Th Lab C. Total Total % %
Hrs Courses Credits Area Overall
Area
Fundamen Computer 1 1 2
tals & Programing
Programming
Computing Numerical Methods
& Software 2 1 3 8 8.42 5.93
Applications 3
Computer
application Process Design &
in Chemical Simulation 2 1 3
Engineering
design
Chemical 3 1 4
Engineering
Thermodynamics-I
Particulate 3 1 4
Technology
Engineering Engineering
Mass Transfer 2 1 3
Foundation Foundation 8 28 29.47 20.74
Chemical Process 3 1 4
Technology
Fluid mechanics-I 3 1 4
Heat Transfer 3 1 4
Principles-I
Principles-II
Instrumentation and
Process Control 3 1 4
Separation 2 1 3
Processes-I
Separation 2 1 3
Processes-II
Major Chemical Reaction 31 32.98 23.13
3 1 4 10
Based Core Engineering
Major
Based Core Fluid Mechanics-II 2 0 2
(Breadth) Transport 3 0 3
Phenomena
Chemical Plant
Design 3 0 3
Process Analysis &
Optimization 3 0 3
Fuels & Energy 3 1 4

Chemical
Engineering 2 0 2
Thermodynamics- II
12
Major 3 0 3 3 9 9.57 7.15
Major Based *Elective-I
Core
(Depth) *Elective-II 3 0 3
*Elective-III 3 0 3
Workshop
practices 0 1 1
Applied Electrical 2 1 3
Engineering
Inter- Inter Engineering 2 0 2
disciplinary Mechanics
Disciplinary
Engineering Engineering
Engineering
Breadth
Breadth
2 0 2 8 14 14.58 10.29
Materials
Computer Aided
Engineering 0 1 1
Drawing
Engineering
0 1 1
Drawing
Maintenance &
Utility Engineering 2 0 2
Process Safety
Management 2 0 2
Design project- 0 3 3
Design Part I
Project
2 6 6.25 4.41
Design project- 0 3 3
Part II
TOTAL 34 96 100 70
Industrial 4-6 weeks industrial training mandatory (Non
Training Credit)
Grand Total 50 136
*Elective subjects may be offered from the pool of subjects given below.
Electives
Chemical Engineering Design Engineering Oil & Gas

Computational Fluid Engineering
Petroleum
Polymer Engineering Dynamics (CFD) Refinery
Engineering
Statistical Gas Processing
Novel Separation Processes Experimental Design
Operation Management Process Design & Petrochemicals
Optimization
Molecular Modeling
13
Mineral Processing
Nanotechnology
Biochemical Engineering Green Engineering Nuclear
Environmental Engineering
Introduction to
Biochemical Engineering Engineering Nuclear
Biochemical Separations Green Technologies & Engineering
sustainable
Development
Industrial Ecology
Biochemical Processes and Nuclear Fuel
Waste Management Fabrication
Products
Sustainability in
Processes & Energy
System
Process Engineering Energetic Materials Energy & Power
Science of Energetic Industrial Energy
Process Analysis & Optimization
Materials Systems
Sustainable
Chemical Wet Processing of Rocket Propulsion
Energy
Textiles
Resources
Explosive Formulation,
Manufacturing & Filling
** New area/subjects can also be included according to the

specialization/availability of the faculty and facilities and need of the
province.
14
Scheme of Studies
BE, BSc Chemical Engineering
Semester 1 Semester 2
Course Title Th Lab C.Hrs Course Title Th Lab C.Hrs
Functional English 3 0 3 Physical & Analytical 3 1 4
Chemistry
Islamic
2 0 2 Pakistan Studies 1 0 1
Studies/Ethics
Chemical Process Applied Mathematics
3 0 3 3 0 3
Principles-I
Engineering Drawing 0 1 1 Applied Physics 3 1 4
Inorganic & Communication Skills
3 1 4 0 1 1
Organic Chemistry
Chemical Process
Calculus & Analytical 3 0 3 3 1 4
Technology
Geometry
Total 14 2 16 Total 13 4 17
First Year Credit
33
Hours
Computer Aided
Workshop Practices 0 1 1 0 1 1
Engineering Drawing
Applied Electrical
Computer
1 1 2 Engineering 2 1 3
Programming
Chemical Engineering
Chemical Process 2 0 2 2 0 2
Thermodynamics-II
Calculations-II
Chemical Chemical Engineering
3 1 4 3 0 3
Engineering Mathematics
Thermodynamics-I
Social Sciences*
2 0 2 Particulate Technology 3 1 4
Fluid Mechanics II
Fluid Mechanics-I 3 1 4 2 0 2
Engineering Process Safety 2 0 2
2 0 2
Mechanics Management
Total 13 4 17 Total 14 3 17
Second Year Credit
34
Hours
15
Mass Transfer 2 1 3 Instrumentation & 3 1 4

Process Control
Chemical Reaction 3 1 4 Fuel & Energy 3 1 4
Engineering
Engineering Materials 2 0 2 Chemical 2 0 2
Engineering
Economics
Heat Transfer 3 1 4 Separation 2 1 3
Processes-I
Numerical Methods & Transport
2 1 3 3 0 3
Software Applications Phenomena
Probability and 2 0 2 Technical Report 2 0 2

Statistics Writing &
Presentation Skills
Total 14 4 18 Total 15 3 18
Third Year Credit
36
Hours
Course Title Lec Lab C.Hrs Course Title Lec Lab C.Hrs
Separation Processes- Entrepreneurship

2 1 3 2 0 2
II
Industrial Management Elective*-II
2 0 2 3 0 3
Chemical Plant Design 3 0 3 Elective*-III 3 0 3
Elective*-I 3 0 3 Process Design & 2 1 3
Simulation
Design Project- I 0 3 3 Design Project-II 0 3 3

Process Analysis and 3 0 3 Maintenance & 2 0 2
optimization Utility Engineering
Total 13 4 17 Total 12 4 16
Final Year Credit
33
Hours
process
Total Credit Hours 136
16
DETAIL OF COURSES
FOR BE, BSc IN CHEMICAL ENGINEERING
SEMESTER 1
FUNCTIONAL ENGLISH
Credit hours: 3 (3,0,0) Prerequisites: N/A
Objectives of the course:

To enhance language skills and develop critical thinking
Course Outline:
Basics of Grammar, parts of speech and use of articles, sentence structure,
active and passive voice, practice in unified sentence, analysis of phrase,
clause and sentence structure, transitive and intransitive verbs, punctuation
and spelling.
Comprehension
Answers to questions on a given text
Discussion
General topics and every-day conversation (topics for discussion to be at the
discretion of the teacher keeping in view the level of students)
Listening
To be improved by showing documentaries/films carefully selected by subject
teachers.
Translation skills
Urdu to English
Paragraph writing
Topics to be chosen at the discretion of the teacher
Presentation skills
Introduction
Recommended Books:
1. Practical English Grammar by A. J. Thomson and A. V. Martinet.
Exercises
1. Third edition. Oxford University Press. 1997. ISBN 0194313492
Exercises Third edition. Oxford University Press. 1997. ISBN 0194313506
3. Writing. Intermediate by Marie-Christine Boutin, Suzanne Brinand and
Francoise Grellet. Oxford Supplementary Skills. Fourth Impression 1993.
ISBN 0 19 435405 7 Pages 20-27 and 35-41.
4. Reading. Upper Intermediate. Brain Tomlinson and Rod Ellis. Oxford
Supplementary Skills. Third Impression 1992. ISBN 0 19 453402 2.
17
ISLAMIC STUDIES/ETHICS

1 To provide Basic information about Islamic Studies
2 To enhance understanding of the students regarding Islamic Civilization
3 To improve Students skill to perform prayers and other worships
4 To enhance the skill of the students for understanding of issues related to
faith and religious life.
5 Interrelationship of Islam and Science (Where we were and where we
are?)
Course Outline:
INTRODUCTION TO QURANIC STUDIES
1) Basic Concepts of Quran
2) History of Quran
3) Uloom-ul -Quran
STUDY OF SELECTED TEXT OF HOLY QURAN

1) Verses of Surah Al-Baqra Related to Faith(Verse No-284-286)
2) Verses of Surah Al-Hujrat Related to Adab Al-Nabi (Verse No-1-18)
3) Verses of Surah Al-Mumanoon Related to Characteristics of faithful (Verse
No-1-11)
4) Verses of Surah al-Furqan Related to Social Ethics (Verse No.63-77)
5) Verses of Surah Al-Inam Related to Ihkam(Verse No-152-154)
STUDY OF SELECTED TEXT OF HOLY QURAN

1) Verses of Surah Al-Ihzab Related to Adab al-Nabi (Verse
No.6,21,40,56,57,58.)
2) Verses of Surah Al-Hashar (18,19,20) Related to thinking, Day of
Judgment
3) Verses of Surah Al-Saf Related to Tafakar,Tadabar (Verse No-1,14)
SEERAT OF HOLY PROPHET (S.A.W) I
1) Life of Muhammad Bin Abdullah (Before Prophet Hood)
2) Life of Holy Prophet (S.A.W) in Makkah
3) Important Lessons Derived from the life of Holy Prophet in Makkah
SEERAT OF HOLY PROPHET (S.A.W) II

1) Life of Holy Prophet (S.A.W) in Madina
2) Important Events of Life of Holy Prophet in Madina
3) Important Lessons Derived from the life of Holy Prophet in Madina
INTRODUCTION TO SUNNAH
1) Basic Concepts of Hadith
2) History of Hadith
3) Kinds of Hadith
18
4) Uloom-ul-Hadith
5) Sunnah & Hadith
6) Legal Position of Sunnah
SELECTED STUDY FROM TEXT OF HADITH INTRODUCTION TO
ISLAMIC LAW & JURISPRUDENCE

1) Basic Concepts of Islamic Law & Jurisprudence
2) History & Importance of Islamic Law & Jurisprudence
3) Sources of Islamic Law & Jurisprudence
4) Nature of Differences in Islamic Law
5) Islam and Sectarianism
ISLAMIC CULTURE & CIVILIZATION

1) Basic Concepts of Islamic Culture & Civilization
2) Historical Development of Islamic Culture & Civilization
3) Characteristics of Islamic Culture & Civilization
4) Islamic Culture & Civilization and Contemporary Issues
ISLAM & SCIENCE

1) Basic Concepts of Islam & Science
2) Contributions of Muslims in the Development of Science
3) Quran & Science
ISLAMIC ECONOMIC SYSTEM

1) Basic Concepts of Islamic Economic System
2) Means of Distribution of wealth in Islamic Economics
3) Islamic Concept of Riba
4) Islamic Ways of Trade & Commerce
POLITICAL SYSTEM OF ISLAM

1) Basic Concepts of Islamic Political System
2) Islamic Concept of Sovereignty
3) Basic Institutions of Govt. in Islam
ISLAMIC HISTORY
1) Period of Khlaft-e-Rashida
2) Period of Ummayyads
3) Period of Abbasids
SOCIAL SYSTEM OF ISLAM

1) Basic Concepts of Social System Of Islam
2) Elements of Family
3) Ethical Values of Islam
Recommended Books:
1) Hameed ullah Muhammad, Emergence of Islam , IRI, Islamabad
2) Hameed ullah Muhammad, Muslim Conduct of State
3) Hameed ullah Muhammad, Introduction to Islam
4) Mulana Muhammad Yousaf Islahi,
19
5) Hussain Hamid Hassan, An Introduction to the Study of Islamic
Law leaf Publication Islamabad, Pakistan.
6) Ahmad Hasan, Principles of Islamic Jurisprudence Islamic Research
Institute, International Islamic University, Islamabad (1993)
7) Mir Waliullah, Muslim Jurisprudence and the Quranic Law of Crimes
Islamic Book Service (1982)
8) H.S. Bhatia, Studies in Islamic Law, Religion and Society Deep & Deep
Publications New Delhi (1989)
9) Dr. Muhammad Zia-ul-Haq, Introduction to Al Sharia Al Islamia Allama
Iqbal Open University, Islamabad (2001)
CHEMICAL PROCESS PRINCIPLES I

Credit hours: 3 (3-0) Prerequisites: N/A
Objectives of the Course:
To impart skills to understand the chemical process calculations and to
find solution of material balance problems in processing units
Course Outline:
Units, dimensions and conversions, Temperature and Pressure scales,
Composition of mixtures, Principles of stoichiometric combination.
Nature of balances: Concept of a balance. Input-output relationships. Steady-
state considerations. Black box approach. Sub-systems and interconnections.
Familiarization with flow sheets. Mass balance diagrams and tables.
Mass balances for items of plant, Choice of basis/datum for balances. Overall
and component balances, Limiting and excess reactants. Balances for
systems with recycle, purge and by-pass streams. Mass balances for
reactive processes. Mass balances for unit operations, Tie components.
Balances for batch and continuous plant.
Recommended Books:
1. Himmelblau David M. Basic Principles and Calculations in Chemical
Engineering. 8 Ed. 2014. Prentice Hall PTR.
th
2. Felder Richard M., Rousseau Ronald W. Elementary Principles of

Chemical Processes 4th Ed. 2015. John Willey & Sons.
3. Reklaitis G.V., Schneider Daniel R. Introduction to Material and
Energy Balances 1983. John Wiley & Sons.
4. Hougen Olaf A., Watson Kenneth M. Chemical Processes Principles.
2004, John Wiley and Sons & CBS Publishers.
5. Chopy & Hicks, Handbook of Chemical Engineering Calculations ,
2nd Ed. 1994 McGraw-Hill Professional Publishing.
20
ENGINEERING DRAWING
To provide skills to understand, draw and interpret technical / engineering
drawings
Course Outline:
Drawing equipment and the use of instruments; Basic drafting techniques and
standards; Geometrical curves including plane curves; Cycloid; Hypocycloid
and Involute. Intersections at various positions of geometrical bodies such
as prisms, pyramids, cylinders and cones: Development of surfaces of prisms,
pyramids, cylinders and cones. Freehand sketching of machine and engine
components, Locking arrangements; Foundation bolts; Stuffing box; Shaft
couplings; Foot step bearing; Pulleys; Engine connecting rod. Concept of
working drawing of component parts of machines and engines. Size
description, dimensions and specifications; Limit dimensioning and geometric
tolerance; Limits; Fits and tolerances; Conventional symbols. Sectioning of
machine and engine components; Orthographic projections and standard
practices. Isometric views with particular reference to piping and ducting.
Introduction to Computer aided drawing software.
Recommended Books:
1. Parkinson, A. C. A First Year Engineering Drawing 1958, Sir Isaac
Pitman & Sons.
th
2. Engineering Drawing and Graphic Technology 14 Edition by T.E.
French, C.J. Vierk and R.J. Foster
3. E n g i n e e r i n g Drawing (53rd Edition, 2014) by N.D. Bhatt, Charotar
Publishing House Pvt. Ltd.
4. E n g i n e e r i n g Drawing and Graphic Technology (14th Edition,1993 ) by
Thomas E. French, Charles Vierck & Robert Foster, McGraw-Hill
Publishing Company
INORGANIC & ORGANIC CHEMISTRY

To acquire knowledge of inorganic and organic chemistry for understanding
unit processes in chemical engineering.
Course Outline:
Overview of periodic table: molecular orbital theory: Chemistry of solutions:
Chemistry of transition metals, coordination compound and radioactive
elements. Crystalline state of metals and lattice structure. Industrial inorganic
Chemistry. Qualitative and group theory of inorganic Chemistry.
Molecular structure and bonding. Organic molecules and functional groups,
21
Inter conversion of functional groups, alkanes, alkenes, alkynes,
stereochemistry. Organic reactions, alkyl halides, alcohols, ethers and
epoxides, oxidation reduction reactions, benzene and aromatic compounds,
polymer chemistry.
Unit Processes; reaction mechanism of sulfonation; nitration; hydrogenation;
amination; halogenation, oxidation, polymerization.
Lab Outline:
Practical exercises relating to the topics covered in theory.
Recommended Books:
th
1. Unit Process in Organic synthesis, P.H. Groggens, McGraw-Hill, 5 Ed.
1984.
2. Inorganic Chemistry, Gary L. Miessler, Donald A. Tarr, Prentice-Hall, 2003.
CALCULUS & ANALYTICAL GEOMETRY

Credit hours: 3 (3,0,0) Prerequisite: N/A
To develop understanding of the concepts of calculus and analytical geometry
with emphasis on applications in Engineering
Course Outline:
Introduction to functions, introduction to limit, derivatives and their
applications, partial derivatives, maxima and minima, integral calculus with
applications including double and triple integrals, vector algebra, introduction
to analytical geometry, straight line, surfaces, cylinders and cones in
Cartesian, cylindrical and spherical coordinates. Complex numbers and
complex variables.
Vector Calculus, Gradient, divergence, curl of the vector, Introduction to tensor
calculus and their Engineering applications.
Recommended Books:
1. George B. Thomas and Ross L. Finney, Calculus and Analytic
Geometry, Addison-Wesley, ISBN: 0201531747.
2. George F. Simmons, Calculus with Analytic Geometry, McGraw-Hill,
ISBN: 0070576424.
3. Gerald B. Folland, Advanced Calculus, Prentice Hall, ISBN:
0130652652.
4. Monty J. Strauss, Gerald L. Bradley and Karl J. Smith, Calculus,
Prentice Hall, ISBN: 0130918717.
22
SEMESTER 2
PHYSICAL & ANALYTICAL CHEMISTRY
To enhance the knowledge of Physical and Analytical chemistry and their
relation with process industry.
Course Outline:
Kinetic theory of gases. Daltons law, Henrys law and Raoults law. Antoine
equation. Relative volatility.
Surface Phenomena: Adsorption, catalysis, enzyme catalysis.
Electrochemistry, including fuel cells. Colloidal chemistry, reaction kinetics and
equilibrium.
Introduction to instrumental techniques involving potentiometery, pH-Metery:
liquid solid chromatography: high performance liquid chromatography, ion
exchange, gas chromatography, plane chromatography. Spectroscopy: Basics
of spectroscopy; UV and visible spectroscopy.
Lab Outline:
Recommended Books:
1. Kuhn, H., Forsterling, H. D., Waldeck, D. H., Principles of Physical
Chemistry 2009, John Wiley & Sons.
2. Analytical Chemistry, G.L. Hargis, Prentice Hall Inc. 2000.
th
3. Analytical Chemistry, G.D. Christian, J. Wiley, 6 Ed. 2003
4. Fundamentals of Analytical Chemistry, D.A. Skoog, D.M. West, FJ. Holler
7th Ed. Harcourt Asia, 2001.
5. Richard M. Pashley; Marilyn E. Karaman. Applied Colloid and Surface
Chemistry. John Wiley and Sons, Ltd. 2004.
Pakistan Studies (Compulsory)

Introduction/Objectives:
Develop vision of historical perspective, government, politics,
contemporary Pakistan, ideological background of Pakistan.
Study the process of governance, national development, issues arising
in the modern age and posing challenges to Pakistan.
Course Outline:
1. Historical Perspective
a. Ideological rationale with special reference to Sir Syed Ahmed Khan,
Allama Muhammad Iqbal and Quaid-e-Azam Muhammad Ali Jinnah.
b. Factors leading to Muslim separatism
23
c. People and Land
i. Indus Civilization
ii. Muslim advent
iii. Location and geo-physical features.
2. Government and Politics in Pakistan
Political and constitutional phases:
a. 1947-58
b. 1958-71
c. 1971-77
d. 1977-88
e. 1988-99
f. 1999 onward
3. Contemporary Pakistan
a. Economic institutions and issues
b. Society and social structure
c. Ethnicity
d. Foreign policy of Pakistan and challenges
e. Futuristic outlook of Pakistan
Recommended Books:
1. Burki, Shahid Javed. State & Society in Pakistan, The MacMillan Press
Ltd 1980.
2. Akbar, S. Zaidi. Issue in Pakistans Economy. Karachi: Oxford University
Press, 2000.
3. S. M. Burke and Lawrence Ziring. Pakistans Foreign policy: An Historical
analysis. Karachi: Oxford University Press, 1993.
4. Mehmood, Safdar. Pakistan Political Roots & Development. Lahore,
1994.
5. Wilcox, Wayne. The Emergence of Bangladesh, Washington: American
Enterprise, Institute of Public Policy Research, 1972.
6. Mehmood, Safdar. Pakistan Kayyun Toota, Lahore: Idara-e-Saqafat-e-
Islamia, Club Road, nd.
7. Amin, Tahir. Ethno - National Movement in Pakistan, Islamabad: Institute
of Policy Studies, Islamabad.
8. Ziring, Lawrence. Enigma of Political Development. Kent England: Wm
Dawson & sons Ltd, 1980.
9. Zahid, Ansar. History & Culture of Sindh. Karachi: Royal Book Company,
1980.
10. Afzal, M. Rafique. Political Parties in Pakistan, Vol. I, II & III. Islamabad:
National Institute of Historical and cultural Research, 1998.
11. Sayeed, Khalid Bin. The Political System of Pakistan. Boston: Houghton
Mifflin, 1967.
12. Aziz, K. K. Party, Politics in Pakistan, Islamabad: National Commission on
Historical and Cultural Research, 1976.
13. Muhammad Waseem, Pakistan Under Martial Law, Lahore: Vanguard,
1987.
14. Haq, Noor ul. Making of Pakistan: The Military Perspective. Islamabad:
National Commission on Historical and Cultural Research, 1993.
24
APPLIED MATHEMATICS
Credit hours: 3 (3,0,0) Prerequisite: N/A
To provide an understanding of analytical solution of h i g h e r o r d e r
a n d p a r t i a l differential equations concerning to transport processes.
Course Outline:
Differential equations and their classification, formation of differential
equations. Differential equations of first order. Methods of solution of
differential equations of first order and first-degree: Separable equations,
homogenous equations, equations reducible to homogenous, exact differential
equations, integrating factor, linear equations, Bernoulli equations, orthogonal
trajectories in Cartesian and polar coordinates, application of first order
differential equations. Non-linear first order differential equations.
Higher order linear differential equations: Homogeneous linear equations of
order n with constant coefficients, auxiliary/characteristics equations. Solution
of higher order differential equation according to the roots of auxiliary
equation. Non- homogenous linear equations. Working rules for finding
particular integral. Cauchy Euler Equation. Application of partial differential
equations for various transport processes in chemical engineering.
Recommended Books:
1. Erwin Kreyszig, Advanced Engineering Mathematics, John Wiley &
Sons, ISBN: 0471728977.
2. John Polking, Al Boggess, David Arnold Differential Equations, Prentice
Hall, ISBN: 0131437380
3. Stephen Goode, Differential Equations and Linear Algebra, Prentice
Hall, ISBN: 013263757X.
4. Larry A. Glasgow, Applied Mathematics for Science and Engineering
2014, Wiley.
APPLIED PHYSICS
To learn the fundamental principles of physics and their applications
Course Outline:
Electrostatics and Magnetism: Coulombs Law. Electrostatic potential energy
of discrete charges, Continuous charge distribution, Gausss Law, Electric field
around conductors. Dielectrics. Dual trace oscilloscope with demonstration.
Magnetic fields. Magnetic force on current. Hall effect. Biot-Savart Law.
Amperes Law, Fields of rings and coils. Magnetic dipole. Diamagnetism,
Paramagnetism and Ferromagnetism.
25
Waves and Oscillations: Free oscillation of systems with one and more
degrees of freedom. Solution for Modes. Classical wave equation. Transverse
modes for continuous string. Standing waves. Dispersion relation for waves.
LC network and coupled pendulums. Plasma oscillations.
Semi-Conductors: Energy levels in a semiconductor, Hole concept, Intrinsic
and Extrinsic regions, PNP, NPN junction. Transistor, LEDs, Amplifiers Optics
and Lasers: Harmonic traveling waves in one dimension. Near and far fields.
Two-slit interference. Huygens Principle. Single-slit diffraction. Resolving
power of optical instruments. Diffraction Grating. Lasers, Population
inversion. Resonant cavities. Quantum efficiency. He-Ne, Ruby and CO2
lasers. Doppler effect and sonic boom.
Modern Physics: Inadequacy of classical physics, Planks explanations of
black body radiation. Photoelectric effect, Compton effect. Bohrs theory of
Hydrogen atom, Atomic spectra, De-Broglie hypothesis, Braggs Law, Atomic
nucleus, Mass energy relation, Exponential decay and half-life. Nuclear
stability and radioactivity, Alpha decay, Beta decay, Gamma decay
attenuation, Fission, Energy release, Nuclear Fusion.
Lab Outline:
Recommended Book:
1. Dale Ewen Applied Physics 2009, Prentice Hall, Inc.
English II (Communication Skills)

Objectives: Enable the students to meet their real life communication needs.
Course Contents:
Paragraph writing
Practice in writing a good, unified and coherent paragraph
Essay writing
Introduction
CV and job application
Translation skills
Urdu to English
Study skills
Skimming and scanning, intensive and extensive, and speed reading,
summary and prcis writing and comprehension
Academic skills
Letter/memo writing, minutes of meetings, use of library and internet
26
Presentation skills
Personality development (emphasis on content, style and
pronunciation)
Note: documentaries to be shown for discussion and review

Recommended Books:
Communication Skills
a) Grammar
Exercises 2. Third edition. Oxford University Press 1986. ISBN 0
19 431350 6.
b) Writing
1. Writing. Intermediate by Marie-Christine Boutin, Suzanne Brinand
and Francoise Grellet. Oxford Supplementary Skills. Fourth
Impression 1993. ISBN 019 435405 7 Pages 45-53 (note taking).
2. Writing. Upper-Intermediate by Rob Nolasco. Oxford
Supplementary Skills. Fourth Impression 1992. ISBN 0 19 435406
5 (particularly good for writing memos, introduction to
presentations, descriptive and argumentative writing).
c) Reading
1. Reading. Advanced. Brian Tomlinson and Rod Ellis. Oxford
Supplementary Skills. Third Impression 1991. ISBN 0 19 453403
0.
2. Reading and Study Skills by John Langan
3. Study Skills by Richard York.
CHEMICAL PROCESS TECHNOLOGY

To familiarize students with conversion of raw materials into finished
products on industrial scale using conventional and green technology.
Course Outline:
History and Development of Chemical Process Industry in Pakistan. Drawing
Symbols of equipment used in a process industry. Drawing of process flow
diagram using computer softwares like MS Visio. Inorganic chemicals
manufacturing (acids, alkali and salts), Soaps and Detergents, Cement and
Ceramics, Glass, Water treatment and Purification, Fertilizers manufacture,
(Urea, Ammonium Nitrate, Super Phosphate, Di-ammonium Phosphate) and
introduction to pesticides, Pulp and Paper manufacture. Sugar Manufacture,
Polymers manufacture (PVC, Phenol and Urea Formaldehyde), Plastics
Additives & Molding Machines and introduction to Rubber, Synthetic fiber
27
(Manufacture of PET). Leather industry. Food and Beverages, Paints &,
coating Industries, Applications of Sustainable and Green technology.
Lab outline:
Recommended Books:
Austin George T. Shreves Chemical Processes Industries 6 Ed.
th
1.
1997, McGraw-Hill International Edition.
2. Haidari Iqbal Chemical Industry in Pakistan,1992. Industrial Research
Service Karachi, Pakistan.
nd
3. Pandey G. N. A Textbook of Chemical Technology 2 Ed. Vol-I & II.
2000. Vikas Publishing House (Pvt) Limited
4. Riegels Handbook of Industrial Chemistry, James A. Kent 2000,
Springer/Van Norstrand/Rein Hold.
5. Kirk Othmer Encyclopedia of Chemical Technology 1999, Inter
Science Publishers.
6. Jacob A. Moulin, Michiel Makkee, Annelies E. van Diepen, Chemical
Process Technology, 2nd Edition, 2013, Wiley.
7. Anne E. Marteel-Parrish and Martin A. Abraham, Green Chemistry and
Engineering: A pathway to Sustainability, 2014, Wiley.
8. Bailey's Industrial Oil and Fat Products, 6 Volume Set, 6th Edition,
Fereidoon Shahidi (Editor), 2005, John Wiley & Sons, Inc.
SEMESTER 3
WORKSHOP PRACTICES
To provide hands on training skills of workshop machines and tools.
Course Outline:
Use of carpenters tools, Exercise in preparing simple joints, Bench fitting
practice, exercise in marking and fittings; Use of measuring instruments.
Smiths forge, exercise in bending, upsetting and swaging. Familiarizing the
students with the following processes: Soldering and brazing, Welding, Heat
treatment, Moulding and casting. Simple machine shop processes, such as
turning, shaping, milling and sheet metal work.
Recommended Books:
1. Chapman, W., Workshop Technology: Part 1 1972, Elsevier Science &
Technology.
2. Chapman, W., Workshop Technology: Part 2 1972, Elsevier Science &
Technology.
28
COMPUTER PROGRAMMING
To develop programming skills to solve problems of Chemical Engineering
Course Outline
Introduction to development of programming languages. Elements of a language:
instructions, data and addresses. Syntax and instruction sets. Mnemonics and
arguments.
Variable types: Names and character sets. Constants and variables; Real
and integer data types; Double precision; character, complex and logical
variables. Pointers, arrays and other data structure concepts. Effective
choice of variable types. Declaration statements, e.g. common, data and
dimension. Format: read, write and print.
Arithmetic operations: Operator symbols. Arithmetic expressions;
Assignment statements. Library functions. Algorithms.
Program structure: Declarations, main program and termination. Input and
output requirements; Use of subroutines and functions. Program flow: use of
DO loops, IF statements, GOTO and labels. Nesting of loops and IF blocks.
Structured programming. Data Input/Output using files.
File handling: Editing. Compiling, linking, loading and executing. Opening and
closing of files. Program development: Sequential modular layout. Choice of
step length and run time. Initial and boundary conditions. Flow diagrams.
Importance of comments. Debugging. Interpretation of error messages.
Functional testing and validation. Good practice.
Lab Outline:
Recommended Books:
1. Sanford, Larry R. and Nyhoff, L., Introduction to FORTRAN 90 for
Engineers and Scientists, Prentice Hall, 1996.
2. Lafore Programming for PC using Turbo C++ SAMS
3. Bob McFarlane, Robert McFarlane, Beginning AutoCAD 2007, Newnes,
2007
4. Wilson, John E., 3D Modeling in AutoCAD, CMP Books, 2001.
5. Bruce A. Finlayson. Introduction to Chemical Engineering Computing.
John Wiley and Sons, Ltd. 2006.
29
CHEMICAL PROCESS PRINCIPLES II
Credit hours: 2 (2,0,0)
Prerequisites: Chemical Process Calculations-I
To study complex problems of simultaneous material and energy balances
in Chemical Engineering Calculations.
Course Outline:
Components of Energy balance. Balances with reaction: Mass and energy
balances for reacting systems. Balances for combustion processes.
Environmental balances. Sub-systems and interconnections. Concept of
integrated pollution control. Case studies on balances for a selection of
important industrial processes. Efficiency and conversion. Standard states.
Temperature dependence. Heat Effects. Application of Computers in
stoichiometric calculations.
Simultaneous mass and energy balances. Temperature and pressure
dependence. Balances for condensing systems. Dynamic balances.
Recommended Books:
1. Himmelblau David M. Basic Principles and Calculations in Chemical
Engineering. 7 Ed. 2003. Prentice Hall PTR
th
2. Felder Richard M., Rousseau Ronald W. Elementary Principles of

Chemical Processes 3rd Ed. 2001. John Wiley & Sons.
3. Reklaitis G.V., Schneider Daniel R. Introduction to Material and Energy
Balances 1983. John Wiley & Sons.
4. Hougen Olaf A., Watson Kenneth M. Chemical Processes Principles.
2004, John Wiley and Sons & CBS Publishers.
Chopy & Hicks, Handbook of Chemical Engineering Calculations, 2
nd
5.
Ed. 1994 McGraw-Hill Professional Publishing.
CHEMICAL ENGINEERING THERMODYNAMICS- I

Credit hours 4 (3, 3, 0) Prerequisites: N/A
To familiarize students with the definitions, concepts, and laws of
thermodynamics and their engineering applications
Course Outline:
Introduction, thermodynamic systems and processes, equilibrium,
thermodynamic variables, intensive and extensive variables, thermodynamic
properties, state functions, derived intensive variables. Types of work, kinetic
and potential energy, the first law of thermodynamics, internal energy,
energy transfer by heat, energy balance, energy analysis of cycles. Quasi-
static processes, reversibility, heat capacities.
30
Property relations relevant to engineering thermodynamics, P-V-T relation,
evaluating thermodynamic properties, generalized compressibility chart Ideal
gas model, internal energy, enthalpy and specific heat of ideal gases,
evaluating changes in specific enthalpy and internal energy for ideal gases,
polytropic process of an ideal gas. Introducing the control volume,
conservation of mass and energy in a control volume, Steady-state and
transient forms of mass and energy rate balances. Second law of
thermodynamics, irreversible processes, entropy, the Carnot cycle.
Applying the second law to thermodynamic cycles, the Carnot cycle. The
Clausius inequality, entropy changes, evaluating entropy data. Entropy
balance for closed systems, entropy rate balance for control volumes,
isentropic processes, isentropic efficiencies of turbines, nozzles, etc.
Equations of state, property relations from exact differentials, fundamental
thermodynamic functions, relations for gas mixtures and multi-component
systems, the Gibbs-Duhem relation.
Applications to flow processes, nozzles, turbines, compressors, Heat Engines,
Refrigeration & Air Conditioning, and Liquefaction of gases.
Lab Outline:
Recommended Books:
1. Smith J.M., Van Ness H.C., Abbott M.M. Chemical Engineering
Thermodynamics 8 Ed. 2005. McGraw-Hill International Edition.
th
Daubert Thomas E. Chemical Engineering Thermodynamics, 1 Ed.

st
2.
1985, McGraw-Hill Book Company.
Sandler Stanley I. Chemical and Engineering Thermodynamics 3 Ed.
rd
3.
John Wiley and Aons, Inc.
4. Eastop, Mc Conkey Applied Thermodynamics National Book
Foundation
5. Moran M. J., Shapiro H. N., Fundamentals of Engineering
Thermodynamics 6th Ed. John Wiley and Sons, Inc.
6. Cengel, Y. A., Boles, M. A., Thermodynamics: An Engineering
Approach, 2008, McGraw-Hill.
FLUID MECHANICS-I
To impart knowledge of the concepts and laws of fluid mechanics, and their
applications in pipe sizing and flow metering.
Course Outline:
Fluid Statics: pressure forces on surfaces, Pressure distribution, Head
Calculations, pressure measuring devices, Buoyancy, Pressure in accelerated
rigid body motions.
31
Nature of Flow: Laminar & Turbulent Flow, Compressible & Non-Compressible
Bernoullis equation and its applications; Continuity Equation, Energy
Relationships & the Bernoulli equation, pressure terminology, diffusers and
sudden expansion.
Momentum of a Flowing Fluid; Newtons 2nd law of motion & Momentum
Balance, Calculations for Laminar & Turbulent pipe flow, nozzle flow & other
example.
Stress in Fluids; Viscosity, Newtons Law of Viscosity, Shear Stress
Components, Newtonian and non-Newtonian flow
Flow of Incompressible Newtonian Fluids in Pipes & Channels Shear stress in
a pipe, Friction factor & pressure drop, Losses in fittings and bend pipes,
enlargements and contractions, friction in non-circular channels, Velocity
distribution for turbulent flow in a pipe. Piping network analysis.
Flow measurement; Orifice meter, Venturi meter, Rota meter, Nozzle. Notch
and Wier, Electromagnetic flow meter, Concept of centrifugal pumps;
Centrifugal pump characteristics; NPSH and its application in chemical
engineering; concept of specific speed; similarity laws in centrifugal pumps;
pumps in series and parallel; Positive displacement pumps, their classification,
characteristics and selection; matching system characteristics with pump
characteristics.
Recommended Books:
Holland, F.A. Bragg, R. Fluid flow for Chemical Engineers, 2 Edition,
nd
1.
Butterworth & Heinemann. 1995.
2. White, F.M. Fluid Mechanics, 7th Edition, McGraw-Hill. 2011.
3. Noel-de-Nevers Fluid Mechanics for Chemical Engineers McGraw-Hill,
2004
4. McCabe Warren L., Smith Julian C., Harriott peter Unit Operations of
Chemical Engineering 7th Edition, 2010. McGraw-Hill Inc.
5. Coulson J.M., Richardson J.F. Chemical Engineering Vol-I, 6th 1999.
Butterworth, Elsevier.
6. Munson B.R., Huebsch W.W., Rothmayer A.P. Fundamental of Fluid
Mechanics Wiley; 7th edition, 2012
7. Fundamental of Fluid Mechanics, 6th Edition.
ENGINEERING MECHANICS

To impart knowledge of mechanics of engineering materials that is generally
part of the process industry.
Course Outline:
General principles of statics; Review of vector addition and subtraction;
32
Cartesian vectors
Position vectors; Force vector directed along a line. Dot product and cross
products. Laws of triangle and parallelogram law of forces. Momentum;
Conditions of equilibrium of particles; Free-body diagrams; Co-planar force
systems. Moment of force; Scalar and vector formulation, Moment of a couple.
Conditions of equilibrium of a rigid body in two dimensions. Free body
diagrams and equations. Structural Analysis; Methods of joints and sections,
Rules for Zero Force members.
Kinematics of particles; Rectilinear and curvilinear motion of particles;
Components of velocity and acceleration kinetics of particles. Newtons second
law of motion; Dynamic Equilibrium. Work; Energy; Power; Impulse and
momentum.
Recommended Books:
1. Bedford, A., Fowler, W. L., Engineering Mechanics: Statics & Dynamics
Principles 2003, Prentice Hall.
2. Hibbeler, R. C., Engineering Mechanics: Statics 2009, Prentice Hall.
SEMESTER 4
COMPUTER AIDED ENGINEERING DRAWING
To enable students to understand and produce 2D and 3D engineering
drawings using CAD tools.
Course Outline:
Introduction to CAD software: User interface; Entity selection; Setting drawing
limits; Using the grid and snap; Creating drawing geometry; Modifying drawing
geometry; Typed input; Using Ortho, polar and object tracking; Object
snapping; Screen.
Manipulation. Transformation commands: Layers; Hatching; Properties; Text
creation and editing; Dimension creation and editing; Layouts/paper space;
Plotting.
Recommended Books:
1. Engineering Drawing and Graphic Technology 14th Edition by T.E.
French, C.J. Vierk and R.J. Foster
2. Elementary Engineering Drawing by N.D. Bhatt.
3. AutoCAD 2002 Users Guide by Autodesk, Mastering AutoCAD 2002 by
George Omura.
33
APPLIED ELECTRICAL ENGINEERING
To impart the basic knowledge of electrical machines and electronic devices
Course Outline:
Introduction to electrical engineering; A.C/D.C Motors, their types and control;
Generators; Transformers; Single and multi-phase. A.C circuits; Power factor;
Introduction to electronics and circuit analysis. Integrated circuits, resisters,
micro- processors. Controller and their types
Recommended Books:
1. Thomas L. Floyd, David M. Buchla, Electronics Fundamentals: Circuits,
Devices, and Applications,8th Ed. 2009, Prentice Hall
2. John Bird, Electrical Circuit Theory and Technology, 2nd Ed., 2003,
Newnes Publication.
3. C.L. Wahdwa, Basic Electrical Engineering, 2nd Ed., 2006, New Age
International Publishers
4. Heinz Schmidt-Walter, Ralf Kories, Electrical Engineering: a pocket
reference, 2007, Artech House
5. Allan R. Hambley, Electrical Engineering: Principles and Applications,
5th Ed., 2010, Prentice Hall
CHEMICAL ENGINEERING THERMODYNAMICS- II

Prerequisites: Chemical Engineering Thermodynamics- I.
To enable students to understand and apply principles of thermodynamics on
equilibrium calculations in multi-component and multiphase systems.
Course Outline:
General Vapour Liquid Equilibrium (VLE) behaviour: Equilibrium criterion and
Raoultss law.
VLE calculations Bubble point, Dew point and Flash calculations.
Partial molar quantities; Excess properties; Chemical potential, fugacity and
activity coefficients; Theory and applications.
Chemical reaction equilibrium and equilibrium constants; single and multi-
reaction equilibria, Dependence of equilibrium constant on T, P, and
composition.
Chemical and phase equilibrium, phase transitions, Gibbs free energy and
phase diagrams, chemical potential, chemical potential in solutions, ideal
reacting gas mixture.
Calculations in Phase Equilibria: Liquid-Liquid; Liquid-Solid. Thermodynamic
Analysis of Chemical Processes.
34
Introduction to Statistical Thermodynamics.
Recommended Books:
1. Smith J. M., Van Ness H. C., Abbott M. M. Chemical Engineering
Thermodynamics 6th Ed. 2001. McGraw-Hill International Edition.
2. Daubert Thomas E. Chemical Engineering Thermodynamics, 1st Ed.
1985, McGraw-Hill Book Company.
3. Sandler Stanley I. Chemical and Engineering Thermodynamics 3rd Ed.
John Wiley and Sons, Inc.
4. Eastop, Mc Conkey Applied Thermodynamics National Book Foundation
5. Moran M. J., Shapiro H. N., Fundamentals of Engineering
Thermodynamics 6th Ed, John Wiley & Sons
6. Cengel, Y. A., Boles, M. A., Thermodynamics: An Engineering Approach,
2008, McGraw-Hill.
CHEMICAL ENGINEERING MATHEMATICS

To focus on use and application of mathematical methods in the areas
relevant to chemical engineering.
Course Outline:
Application of following mathematical techniques to the chemical engineering
problems, Laplace transform, solution of differential equations using laplace
transforms, fourier transform and its applications. Special functions e.g.
gamma function, error function, bessel function.
Vector calculus, gradient, divergence, and curl of a vector and their
applications. Introduction to tensor calculus.
Matrices: Addition & multiplication of matrices, determinant of matrices.
Recommended Books:
1. Edwards, C., and D. Penney. Elementary Differential Equations with
Boundary Value Problems. 6th Ed. Upper Saddle River, NJ: Prentice Hall,
2003.
2. Erwin Kreyszig, Advanced Engineering Mathematics, John Wiley, 2006.
PARTICULATE TECHNOLOGY
To provide understanding of the fundamentals of particle technology with the
emphasis on applications in chemical and process industries
Course Outline:
Characterization of particle and particulate systems (Sieve analysis, Particle
size analysis); Processing (Granulation, Sedimentation); Particle Formation
35
(Granulation, Size Reduction); Description & Energy calculations for coarse
to ultrafine size reducing equipment, Agglomeration.
Storage and Transport (Hopper Design, Conveyers and its t ypes
Pneumatic Conveying, Standpipes, Slurry Flow); Mechanical Separation
(Filtration and its types, Settling, Cyclones); Properties of Particulate Systems
(Colloids, Respirable Drugs, Coal-Water Slurries, Slurry Rheology ). Hazards
identification of Mechanical equipment. Motion of particles in fluid; drag force
on a spherical particles, motion of bubbles and drops, accelerated motion of
particles in centrifugal field.
Sedimentation of fine particles and coarse particles
Solid-Liquid mixing; types of mixing and mixing mechanism. Equipment for
solid-liquid mixing
Flow through porous media, Carman-Kozney equation
Electrostatic Precipitation: Basic operating principles, the physics of
precipitation, factors effecting the design and performance of electrostatic
precipitators.
Powder, ultra-fine and nanoparticles technology
Lab Outline:
Recommended Books:
1. McCabe Warren L, Smith Julian C, Harriott Peter., Unit Operations, 7th
Edition, 2010, McGraw-Hill Inc.
2. Coulson J. M, Richardson J. F., Chemical Engineering- Particle
technology and separation processes Vol 2, 5th Ed. 2007, Pergamon
Press.
3. Martin Rhodes, Introduction to Particle Technology, 2nd Ed. 2008, John
Wiley & Sons, Ltd.
4. Richard G. Holdich, Fundamentals of particle technology, 2002,
Midland Information Technology and Publishing.
5. Enrique Ortega-Rivas, Unit Operations of Particulate Solids: Theory and
Practice 2012, CRC Press.
6. Particle Technology, Hans Rumpf4th Edition. 2013.
FLUID MECHANICS-II
Credit hours: 2 (2,0,0) Prerequisites: Fluid Mechanics-I.
To impart in-depth knowledge about the selection and design of fluid flow
systems in process industry.
Course Outline:
Flow of Compressible Newtonian Fluids
Flow through porous media; Fluidization and types of fluidized beds and
36
their use in chemical engineering, Particle and Regime classification,
minimum fluidization and particulate fluidization, entrainment and elutriation,
concept of hydrodynamic characteristics of fluidized beds, bubbling
fluidization, turbulent fluidization, slurry bed fluidization. Industrial
application of fluidization.
Introduction to non-Newtonian fluids
Flow through packed beds, types of packing, hydrodynamics of packed column
Fluid Motion in the Presence of Solid Particles, Relative motion between a fluid
and a single particle, Effect of presence of other particles and wall on the
particle velocity Turbo-machinery and its classifications. Compressors, their
classification, characteristics and selection. Turbines, their classification and
selection. Compressible flow and its application in chemical engineering,
concept of choked flow.
Lab Outline:
Recommended Books:
1. Holland, F. A. Bragg, R. Fluid flow for Chemical Engineers, 2nd
Ed., Butterworth & Heinemann. 1995.
2. White, F.M. Fluid Mechanics, 7th Ed., McGraw-Hill. 2011.
3. Noel-de-Nevers Fluid Mechanics for Chemical Engineers McGraw-Hill,
2004
Chemical Engineering 7th Ed., 2010. McGraw-Hill Inc.
5. Coulson J.M., Richardson J.F. Chemical Engineering Vol-I, 6th 1999.
Butterworth, Elsevier.
6. Munson B.R., Huebsch W.W., Rothmayer A.P. Fundamental of Fluid
Mechanics Wiley; 7th Ed., 2012
7. Seppo A. Korpela, Principles of Turbomachinery, 2012, Wiley.
PROCESS SAFETY MANAGEMENT

Familiarization of international standards & the importance of safety and the
occupational health viz-a viz environment related to chemical industries
Course Outline:
Importance of safety with increased productivity, Overall safety of plant and
personnel; Accident and loss statistics. Accident analysis and prevention.
Types of accidents in chemical industry. Regulations and standards for
industrial safety. Difference between accident and incident. Accident rate
calculations and economics of accident prevention. Safety management.
Hazard and risk assessment. Accident investigation and case history. Fires
and explosions. Fire triangles. Flammability characteristics. Safety
37
equipment, fire-fighting equipment and their uses. Occupational diseases
related to chemical industry.
Environmental impacts and quality standards
Recommended Books:
1. Crowl D.Y., Louvar J.F., Chemical Process Safety Fundamentals with
Applications, 1990, Prentice Hall.
2. Marc J. Assael and Konstantinos E. Kakosimos, Fires, Explosion and
Toxic Gas Dispersion, 2010, CRC Press.
3. Charles E. Thomas, Process Technology: Safety, Health, and
Environment By Charles E. Thomas 3rd Edition, 2005.
4. Reynold L. Hoover, Health, Safety, and Environmental Control, 2nd Edition
2000.
5. Stephen Asbury ,Health and Safety, Environment and Quality Audits: A
Risk-based Approach, 2nd Edition.1999.
6. By Elearn ,Managing Health, Safety and Working Environment, 2nd
Edition.
SEMESTER 5
MASS TRANSFER
To impart knowledge of fundamental laws of mass transfer their
applications for stage operations
Course Outline:
Classification of mass transfer operations; the choice of mass transfer
methods; Design principles. Molecular Diffusion in fluids and solids; Ficks
law of Diffusion; steady state diffusion in fluids at rest or in laminar motion.
Concept of mass transfer coefficients, their calculation in laminar and
turbulent flows; Interphase mass transfer; Equilibrium and diffusion across the
interface and the concept of stages. Phase equilibrium in Mass transfer.
Distillation: The fractionating column. Lewis-Sorel; McCabe-Thiele methods.
Importance of the reflux ratio; Calculation of minimum reflux ratio; Number of
plates at total reflux; Underwood and Fenske methods; Selection of economic
reflux ratio. Effect of multiple feeds and side streams. Plate efficiency and
Murphrees formula. Concept of a theoretical plate and HETP. Method of
transfer units and HTU. Enthalpy-concentration method.
Multi-component distillation: Degrees of freedom in separation specifications.
Key components in multi-component mixtures and recovery fraction.
Continuous flash distillation with heat balancing; Equilibrium and enthalpy
expressions; Multi-stage distillation; Numerical examples of multi- component
separation problems; Side streams and partial condensers. Column Design:
Tray design; hydraulics and performance.
38
Batch distillation: operation at constant product composition or constant reflux
ratio. Calculation of column diameter and height.
Lab Outline:
Recommended Books:
1. McCabe Warren L., Smith Julian C., Harriott Peter Unit Operations of
Chemical Engineering 7th Ed. 2005. McGraw-Hill Inc.
2. Coulson J.M., Richardson J. F. Chemical Engineering Vol-II, 5th Ed.
2002. The English Book Society and Pergamon Press.
3. Incropera Frank P., De Witt David P. Fundamentals of Heat and Mass
Transfer 3rd Ed. 1990. John Wiley and Sons.
4. Treybal Robert E. Mass Transfer Operations, 1981, McGraw-Hill Book
Company.
5. Schweitzer, Handbook of Separation Techniques for Chemical
Engineers, 1979, McGraw-Hill Book Co.
6. Coulson J. M., Richardson J. F. Chemical Engineering Vol-I, 1999. The
English Book Society and Pergamon Press
7. Alan S. Foust, Leonard A. Wenzel Principles of Unit Operations 2nd
Ed.1980. John Wiley & Sons.
8. Diran Basmadjian. Mass Transfer and Separation Process (Principles
and Applications) CRC Press Taylor and Francis Group. 2007.
CHEMICAL REACTION ENGINEERING

Prerequisites: Chemical Engineering Thermodynamics, Physical &
Analytical Chemistry.
To provide in-depth knowledge of the application of laws of thermodynamics,
reaction kinetics for the economical design of chemical reactors.
Course Outline:
Kinetics of homogeneous reactions: Rate of reaction, variables affecting the
rate of reaction, order of reaction, rate constant; searching for a mechanism
of reaction, activation energy and temperature dependency, Interpretation of
batch reactor data for single and multiple reactions. Integral method and
differential method of analysis for constant volume and variable volume batch
reactors. Search for a rate equation.
Design of homogeneous reactors: Batch, Mixed flow, Plug flow reactors,
Comparison of single reactor, multiple reactor systems in parallel/series.
Temperature and pressure effects, Adiabatic and non-adiabatic operations.
Design of heterogeneous reactors: Surface phenomenon and catalysis,
adsorption/desorption isotherms, Heterogeneous reaction systems, Rate
equations for heterogeneous reactions, Determination of rate controlling
steps. Kinetics of solid catalyzed reactions. Catalyst deactivation and
39
regeneration. Design of fixed bed and fluidized bed catalytic reactors.
Lab Outline:
Recommended Books:
1. H. Scott Fogler Elements of Chemical Reaction Engineering 4th Edition,
Prentice Hall; 2005
2. Levenspiel Octave. Chemical Reaction Engineering 3rd Ed. 2006, John
Wiley & Sons Inc.
3. Smith J. M. Chemical Engineering Kinetics 2001, McGraw-Hill Book Co.
4. E Bruce Nauman Chemical Reactor Design, Optimization and Scale up
McGraw-Hill 2002.
5. Charles and Thatcher Introduction to Chemical Engineering Kinetics and
Reactor Design Second Ed. 2014 John Wiley
ENGINEERING MATERIALS
Credit hours: 2 (2,0,0) Prerequisites: N/A.
To impart knowledge of engineering materials, their characteristics, testing
and applications.
Course Outline:
Stress, strain, modulus, elastic and plastic behaviour of materials. Physical,
mechanical, thermal properties and characterization. Properties, classification
and application of materials of construction such as Iron, steel, stainless
steel, Nickel, haste alloy, copper alloys, A luminium and its alloys, lead,
titanium and tantalum, PVC, Teflon, poly-olefins, PTFE glass, stone ware,
acid resistant bricks and tiles. Biomaterials, Composites, Ablatives and
thermal insulation materials. Electrical and optical properties of materials,
biodegradable materials and recyclable materials.
Nature, types and rate of corrosion, corrosion protection, surface treatment,
heat treatment. Material selection; Material testing (destructive and non-
destructive testing); International standards for material testing.
Introduction to nano-materials.
Lab Outline: N/A
Recommended Books:
1. William D. Callister, D. G. R. (2014). Materials Science and Engineering:
An Introduction (9th Ed.). John Wiley & Sons, Inc.
Srivastava C. M., Srinivasan C. Science of Engineering Materials 2
nd
2.
Ed.2000, New Age International (PRACTICALS) Limited, Publishers.
3. Varnon John. Introduction of Engineering Materials MacMillan.
4. William F. Smith. Principles of Materials Science and Engineering
McGraw-Hill.
5. R. A. Flinn and P. K. Trjan Engineering Materials and Their Applications
Jaico.
40
6. Ijaz Hussain Khan. Corrosion Technology, Vol-I and 2, Institute of
Chemical Engineering, University of the Punjab, Lahore, Pakistan.
HEAT TRANSFER
To develop understanding of the governing laws of heat transfer for designing
heat transfer equipment.
Course Outline:
Difference between thermodynamics and heat transfer; modes of heat transfer:
Conduction; Fouriers law of heat conduction, steady state one dimensional
heat conduction without and with heat generation, conduction in multi layers
geometries and its application in insulation. Unsteady state heat conduction;
Introduction to heat conduction in two dimensions.
Convection; concept of free and forced convection; concept of heat transfer
coefficient and Newtons law of cooling; forced convection in laminar and
turbulent flows in pipes and on flat plates; Use of dimensional analysis in
convection, concept of overall heat transfer coefficient; Concept of thermal
boundary layer and its analogy with momentum boundary layer.
Radiation heat transfer; laws of radiation, radiation surface behaviour
concept of shape factor for black body and non-black body radiation.
Heat transfer equipment, types and selection criteria; types of heat
exchangers and design; heat transfer with phase change; boiling and
condensation; the boiling curve; evaporators and their design. International
standards, e.g. TEMA and IPS standards shall be followed.
Lab Outline:
Recommended Books:
1. Kern Donald Q. Process Heat Transfer, 1997, McGraw-Hill Book
Company.
2. Cengel Yunus A. Heat Transfer-A Practical approach, 1988,
McGraw-Hill Book Company.
Transfer 5th Ed. 2002. John Wiley and Sons.
4. Coulson J.M., Richardson J.F. Chemical Engineering Vol-I, 1999. The
5. Coulson J.M., Richardson J.F. Chemical Engineering Vol-II, 5th Ed.
2002. The English Book Society and Pergamon Press
6. Hewitt Bott. Process Heat transfer
7. J. P. Holman, Heat Transfer, 2002, McGraw-Hill Book Company.
41
NUMERICAL METHODS AND SOFTWARE APPLICATIONS
To enable students to use structured programming techniques in suitable
programming languages and implement numerical solutions using software
tools e.g. MATLAB, MATHEMATICA etc.
Course Outline:
Linear Algebra: Matrix and First-order Linear Systems. Eigen values and
Eigen vectors. Finite difference and theory of interpolation; Iterative methods;
Taylor, Newton Series etc. Approximation zeros (roots); numerical
integration and differentiation. Iterative methods for solution of linear
systems, design value problems, numerical solutions of ordinary differential
equations.
Linear algebra applications: matrix calculations, solution of linear equations,
Eigen value calculation. Numerical solution/calculation of integrals,
derivatives and differential equations. Transfer function manipulation and
study of transient response of various first and second order systems, plotting
Bode and Root Locus diagrams. Introduction to simulations using software
tools.
Lab Outline:
Practical exercises relating to the topics covered in theory using software tools
e.g. MATLAB, MATHEMATICA etc.
Recommended Books:
1. Zhilin Li, Lubin & Vulkov, Jerzy Wasniewski, Numerical analysis and its
applications, Springer, 2005, ISBN 3540249370.
2. Michelle Schatzman, Numerical Analysis Oxford University Press,
2002, ISBN 0198508522.
3. Steven T. Karris, Numerical Analysis Orchard Publications, 2004,
ISBN 0974423912.
Probability & Statistics

Credits: 2 (2,0,0) Prerequisite: N/A
To prepare the students for the statistical analysis of data to
quantify the errors
Course Outline:
Statistical treatment of data. Probability analysis and distribution including
random variables, binomial distribution, poisson approximation to binomial
distribution, Probability density function. Sampling distribution. Regression
analysis. Scientific notation and significant figures. Types of errors in
experimental measurements. Units in different systems. Graphical Techniques
(Log, semi-log and other non-linear graphs). Applications of statistical analysis
42
software i.e. SPSS, STATA, R, etc.
Recommended Books:
1. Kenneth. Lange, Statistical Methods, Springer, 2002, ISBN 0387953892.
2. Montgomery, D.C., and Runger, G.C., Applied Statistics and Probability
for Engineers, John Wiley & Sons, 2001.
SEMESTER 6
INSTRUMENTATION & PROCESS CONTROL
To impart knowledge of instruments and control in order to design control
systems for chemical process industry.
Course Outline:
Study of scientific principles employed in instruments; sensors, modifiers,
recorders etc. Dynamic and static properties of instruments; selection and
calibration of instruments; error analysis of process measurement; Instrument
Identification and Line Symbols; Available technology of instrumentation for
temperature, flow, level, weight, load, pressure, composition and pH
measurement. Transducers; advanced measurement devices employing
piezoelectric current, ultrasonic, laser, microwave etc. final control elements;
Installation of different types of sensors with economic considerations; Types
of Controller, Design and Hardware elements of control Case studies based
on installation and commissioning of different types of sensors on the basis of
economics and technology.
Introduction and significance of control; Feedback and feed forward control;
Design and Hardware elements of control; Dynamics of first and second
order systems; Overall transfer function testability; Controllers (P, PI, PID
etc.), final control elements; Dynamic behavior of feedback controlled
processes, Representation of control systems; Multiple control loops;
cascade, ratio, over-riding etc. Introduction to stability of chemical processes,
tuning of feedback control loops; introduction to frequency response
m e t h o d s /techniques; Routh's criteria, Bode plots, Nyquit method;
Computer control, Introduction to Distributed Control Systems; Case study:
Development of control scheme of complete plant. Development of P & ID.
Safety instrumented system.
Lab Outline:
Recommended Books:
1. Smith, C. A, Corripio, A. B, Principles and Practice of Automatic Process
Control, John Wiley, 3rd Edition 2006.
2. Marlin, T.E., Process Control, 2nd Ed., McGraw-Hill Book Co., 2000.
3. Ogunnaike, B. A., et al., Process Dynamics, Modeling, and Control,
43
Oxford University Press, 1997.
4. Coughanowr, D. R. and S. E. LeBlanc,, Process system Analysis &
Control, 3rd Edition, 2009, McGraw-Hill.
5. Process Control Instrumentation Technology, Curtis D. Johnson,
Pearson Education 2003.
6. Chemical Process Control, G. Stephanupolos, Prentice Hall 2002
7. Essentials of Process Control, W.L. Luyben McGraw-Hill 1997.
FUELS & ENERGY


To provide in-depth knowledge of selection and efficient utilization of fossil fuels
and alternate & sustainable energy resources.
Course Outline:
Survey of available energy resources. Introduction and survey of locally
available fuels, industrial fuels: Classification and storage of solids, liquids and
gaseous fuels: Criteria and characterization for the selection of fuels for
industrial purposes; Carbonization, liquefaction and gasification of coal;
Synthetic fuels; Petroleum refining, natural gas processing & syngas production
Fuel up gradation, Fishertrops process and clean coal technology
Furnaces, Burners and their performance Biomass Sources, Pretreatment of
biomass for thermo-chemical conversion, methods of production of fuels from
biomass, Gasification and liquefaction of forest products, Biomass volatilization,
Kinetics of gasification, Ethanol and Methanol production from biomass.
Nuclear and Solar energy, hydel power, wind and tidal energy, geothermal
energy. Energy conservation, methodologies of selected systems.
Lab Outline:
Recommended Books:
1. Turns, S. R. An Introduction to Combustion 2nd Edition McGraw-Hill. 2000.
2. Griffiths, J. F. & Barnard, J. A. Flame and Combustion, 3rd Edition,
Blackie Academic & Professional. 1995.
3. Harker J. H., Backhurst J. R. Fuel and Energy, 1981, Academic Press
4. Probstein, Synthetic Fuels, McGraw-Hill.
5. Marion Smith, Fuels and Combustion, McGraw-Hill.
CHEMICAL ENGINEERING ECONOMICS

To familiarize students with the importance of economics and its application
in chemical engineering design for the purpose of cost estimation,
profitability and economic feasibility.
44
Course Outline:
Engineering economy basics: Measures of financial effectiveness; Non-
monetary factors and multiple objectives; principles of engineering economy.
Consumer and producer goods; Measures of economic worth; Price, Supply
and Demand relationship; Production; Factors of production; Laws of return ,
Taxation & Insurance
Depreciation calculation Sunk and opportunity costs; Fixed, variable, and
incremental costs; Recurring and nonrecurring costs; Direct, indirect, and
overhead costs; Standard costs; Breakeven analysis; Unit cost of production;
Cost-benefit analysis; Feasibility studies; Value analysis in designing and
purchasing.
Economic evaluation of processes and equipment; Payback period method;
Present worth method; Uniform annual cost method; Rate of return method
(including Internal Rate of Return).
Manufacturing lead time; Production rate; Capacity; Utilization; Availability;
Work in process; WIP and TIP ratios.
Types of ownership; types of stock; Partnership & joint stock companies;
Banking and specialized credit institutions.
Islamic and Contemporary financing systems and their use in cost estimation.
Recommended Books:
1. Leland Blank, and Anthony Tarquin, Engineering Economy, 6th Edition,
McGraw-Hill, 2005.
2. G. J. Thuesen, and W. J. Fabrycky, Engineering Economy, 9th Edition,
Prentice Hall of India, 2005.
3. Ted G. Eschenbach, Engineering Economy, 2nd Edition, Oxford
University Press, 2003.
4. James L. Riggs, David D. Bedworth, and Sabah U. Randhawa,
Engineering Economics, 4th Edition, Tata McGraw-Hill, 1996.
5. James L. Riggs, and Thomas M. West, Essentials of Engineering
Economics, 2nd Edition, McGraw-Hill, 1986
6. Engineering Economy (9th Edition, 2008) by Gerald J. Thuesen and W.J.
Fabrycky, Prentice Hall.
7. Engineering Economy (7th Edition, 2011) by Leland Blank and Anthony
Tarquin, McGraw-Hill.
8. Engineering Economy (3rd Edition, 2010) by Ted G. Eschenbach, Oxford
University Press.
9. Engineering Economics (4th Edition,1996) by James L. Riggs and David
D. Bedworth, McGraw-Hill.
10. Process Engineering Economics (Chemical Industries) (1st Edition, 2003)
by James R. Couper ,CRC Press.
11. Engineering Economy (16th Edition, 2014) by William G. Sullivan & C.
Patrick koelling, Prentice Hall. mes L. Riggs, and Thomas M. West,
Essentials of Engineering Economics, 2nd Edition, McGraw-Hill, 1986
45
Separation Processes I
Equipment for gas liquid operations; Equipment where the gas is dispersed;
sparged vessels column, tray towers; Equipment where liquid is dispersed,
packed towers, venturi scrubbers. Equipment for liquid operations; mixer
settlers and pulse columns. Equipment for solid fluid operations; leaching,
drying, adsorption and ion exchange.
Absorption: Extension of design techniques to absorption.

Liquid-Liquid extraction: Introduction, Extraction Processes, Equilibrium data,
Calculation of the number of theoretical stages for various cases of
countercurrent and co-current operations.
Humidification and Cooling Towers: Humidification terms, wet-bulb and
adiabatic saturation temperature, Humidity data for the air-water system,
temperature- humidity chart, enthalpy-humidity chart, determination of
humidity, humidification and dehumidification.
Cooling Towers: Basic principles, types, features and operation of various
cooling towers. Cooling tower design; Alternative sinks for waste heat. Design
of equipment based on worst case scenarios. Water and air based systems.
Environmental effects.
Drying: General principles; Rate of drying; The mechanism of moisture
movement during drying; Diffusion and Capillary theory of drying; Classification
and selection of dryers (Tray, tunnel, rotary, drum, spray, pneumatic, fluidized
beds, turbo-shelf, disc and centrifuge dryers), solvent drying, superheated
steam drying, freeze drying, flash drying, partial-recycle dryers; The drying of
gases.
Recommended Books:
1. McCabe Warren L., Smith Julian C., Harriott Peter Unit Operations of
2. Coulson J.M., Richardson J. F. Chemical Engineering Vol-II, 5th Ed. 2002.
The English Book Society and Pergamon Press.
4. Treybal Robert E. Mass Transfer Operations, 1981, McGraw-Hill Book
Company.
5. Schweitzer, Handbook of Separation Techniques for Chemical Engineers,
1979, McGraw-Hill Book Co.
6. Coulson J. M., Richardson J. F. Chemical Engineering Vol-I, 1999. The
7. Alan S. Foust, Leonard A. Wenzel Principles of Unit Operations 2nd Ed.
1980. John Wiley & Sons.
8. Diran Basmadjian. Mass Transfer and Separation Process (Principles and
Applications) CRC Press Taylor and Francis Group. 2007.
46
TRANSPORT PHENOMENA
Credit hours: 3 (3,0,0) Prerequisites: Fluid Mechanics-I.
To develop comprehensive models of chemical engineering operations
based on the theories of momentum, mass, and energy transport.
Course Outline:
Transfer processes: A review of the mechanisms of momentum, energy and
mass transport.
Momentum transport: Derivation of equations of continuity and motion
(Navier- Stokes equation). Application in laminar and turbulent flow problems.
Energy transport: Derivation of energy equation. Application to heat transfer
problems involving conduction, forced and free convection. Application in
laminar and turbulent flow problems.
Mass transport: Derivation of species conservation equations for binary and
multi- component mixtures. Application to mass transfer problems with and
without chemical reaction. Application in laminar and turbulent flow problems.
Recommended Books:
1. Bennett C. O., Myers J. E. Momentum, Heat & Mass Transfer 3rd Ed.
1983. McGraw-Hill Book Company.
2. Bird R. Byron, S Warren E., Lightfoot Edwin N. Transport Phenomena ,
Revised 2nd Edition, 2007, John Wiley & Sons Inc.
3. B Robert S., Hershey Harry C. Transport PhenomenaA Unified
Approach, 1988, McGraw-Hill International Editions.
5. James Welty, Charles E. Wicks, Gregory L. Rorrer, Robert E. Wilson,
Fundamentals of Momentum, Heat and Mass Transfer, 5th Edition, 2008,
Wiley.
TECHNICAL REPORT WRITING & PRESENTATION SKILLS

To enhance the report writing & presentation skills and develop interpersonal
communication expertise
Course Outline:
Presentation skills
Introduction to basic concepts; features of effective presentation, best
practices.
Essay writing
Descriptive, narrative, discursive, argumentative.
47
Academic writing
How to write a proposal for research paper/term paper.
How to write a research paper/term paper (emphasis on style, content,
language, form, clarity, consistency).
Technical Report writing
Introduction to basic concepts, important aspects of technical reports
and documentation, best practices.
Recommended Books:
1. Writing. Advanced by Ron White. Oxford Supplementary Skills. Third
Impression 1992. ISBN 0 19 435407 3 (particularly suitable for
discursive, descriptive, argumentative and report writing).
2. College Writing Skills by John Langan. McGraw-Hill Higher Education.
2004.
3. Patterns of College Writing (4th Edition) by Laurie G. Kirszner and
Stephen R. Mandell. St. Martins Press.
SEMESTER 7
SEPARATION PROCESSES II
Prerequisites: Heat Transfer, Mass Transfer.
To provide understanding of design strategies of separation equipment
involving simultaneous heat and mass transfer operations.
Course Outline:
Adsorption: Introduction, The nature of adsorbents, Adsorption equilibria,
Adsorption from liquids, structure of adsorbents, Adsorption equipment and
regeneration of spent adsorbents.
Ion exchange: principles, applications and equipment. Membrane Separation
Processes.
Leaching: General principles, Factors influencing the rate of extraction, Mass
transfer in leaching operations, Equipment for leaching, Calculation of the
number of stages by graphical methods.
Crystallization: Growth and properties of crystals, saturation and nucleation,
crystallization rate, impurities, effect of temperature on solubility. Solubility and
phase diagram, fractional crystallization, caking, crystallizers, principles of
construction and operations.
Azeotropic and Extractive distillation: Heterogeneous azeotropes; Illustrative
examples of azeotropic distillation. Reactive distillation.
48
Lab Outline:
Recommended Books:
2. Coulson J. M., Richardson J. F. Chemical Engineering Vol-II, 5th Ed.
2002. The English Book Society and Pergamon Press.
3. Coulson J. M., Richardson J. F. Chemical Engineering Vol-I, 1999.
The English Book Society and Pergamon Press
4. Foust Alan S., Wenzel Leonard A., Clump Curtis W., Maus Louis and
Anderen L. Bryce Principles of Unit Operations 2nd Ed. , 1963, John
Wiley and Sons.
6. Treybal Robert E. Mass Transfer Operations, 1 981, McGraw-Hill Book
Company
7. Christie J. Geankoplis, Transport Processes and Unit Operations, 4th
Ed., 2003, Prentice Hall Professional Technical Reference
INDUSTRIAL MANAGEMENT
To provide understanding of the principles and techniques of industrial
management.
Course Outline:
Introduction to Industrial Management; Productivity, Plant Layout; Product &
Process layout analysis and comparison; Material handling considerations in
layout. Production planning methods, material requirement planning, material
resource planning. Capacity planning and control; Production control systems;
Job shop scheduling; Quality Control; Production control charts; Scheduling
techniques; Purchasing and procurement. Inventory control; EOQ/EPQ
models (calculations based on EOQ). Time and Motion study.
Organizational structure, Human resource management. Project
management principles, PERT/CPM, total quality management, ISO
standards, labour and engineering laws. Labour problems; Labour
organizations; Prevention & settlement of disputes.
Recommended Books:
1. Harold Kerzner, Project Management: A Systems Approach to Planning,
Scheduling, and Controlling, Ninth Edition, John Wiley & Sons, 2006.
2. Jay Heizer and Barry Render, Principles of Operations Management, 3rd
Edition, Prentice Hall, 1999.
3. Jay Heizer and Barry Render, Operations Management, 5th Edition,
Prentice Hall, 2000.
49
4. Industrial Management Methods Ronald Hurst.
5. Industrial Organization & Management BETHEL.
6. Principles of Management Design Robert E. Parr.
7. Operations Management (11th Edition, 2013) by Jay Heizer and Barry
Render, Prentice Hall.
8. Principles of Operations Management (9th Edition,2013) by Jay Heizer and
Barry Render, Prentice Hall.
9. Fundamentals of Project Management (4th Edition, 2011) by Joseph
Heagney , Amacom.
CHEMICAL PLANT DESIGN

Prerequisites: Heat Transfer, Mass Transfer.

To integrate applications of design practices and techniques by using
international codes and standards for chemical plants
Course Outline:
Process design and development. General design considerations. Design
codes, standards & materials selection.
Vessel design: Low, medium and high pressure storage and transportation
vessels; Cryogenic vessels
Design of mass transfer equipment; material transport; material handling. Heat
transfer equipment including furnaces and refrigeration units. Piping and
pipeline design.
Basic Concepts of Cost Indexing & Optimization: Optimization of Unconstrained
Functions; Linear Programming Applications; Non-Linear Programming with
Constraints.
Engineering Ethics; Local, Global Impact Analysis.
Recommended Books:
1. Peters Max S., Timmerhaus Klaus D. Plant Design and Economics for
Chemical Engineers 4th Ed. 1991. McGraw-Hill Inc.
2. Ludwig Ernest E. Applied Process Design for Chemical and
Petrochemical Plants Vol 1, 2 & 3, 3rd Ed. 2002, Gulf Publishing
Company.
3. Walas Stanley M. Chemical Process Equipment Selection and Design
Butterworth Heinemann 1999.
4. Coulson J. M, and Richardson, Chemical Engineering, Vol VI,
Butterworth Heinemann 1999.
5. Wells G. L. Rose L. M. The art of Chemical Process Design 1986.
Elsevier.
6. Smith Robin Chemical Process Design 1995. McGraw-Hill Inc.
50
7. Backhurst & Harker, Chemical Process Design, John Wiley
8. Evans, Handbook of Chemical Equipment Design
9. E. L. Cussler and G. D. Moggridge, Chemical Product Design, 2001,
Cambridge University Press.
10. Special Issue of Chemical Engineering Research and Design, Part A 80
(A1), 2002 on Process and Product Development
11. James Wel, Molecular Structure and Property: Product Engineering, Ind.
Engg. Chem. Res. 41(8) 1917-1919 (2002)
12. Robbin Smith, Chemical Process : Design and Integration, 2005, Wiley.
DESIGN PROJECT- Part I

ELECTIVE-I
PROCESS ANALYSIS & OPTIMIZATION

To impart knowledge of various models used for process and performance
analysis for optimization in process industry.
Course Outline:
Use of models in process engineering: Model as a working description of a
system. Types and function of model: mechanistic, empirical, stochastic,
procedural and qualitative. Reasoning for using models. Strategy for model
building: Relationship between engineering and mathematical
approximations. Example of dynamic delay of air heater. Conceptual models.
Formulation of functional mechanistic models based on conservation
equations. Coordinate free methods based on vector/matrix notation. Models
for complex and irregular geometry. Case study examples for heat exchanger
and tubular reactor definition of system parameters consistent with the
model. Averaging and model reduction techniques. Numerical procedures
based on weighted residuals.
Adaptive models: Empirical models based on non-linear regressive adaptive
refinement of models. State variables models and matrix differential
equations. Filtering and continuous up-dating of models. State estimation and
adaptive control. Population balance models: Description of process in terms
of distribution functions based on principal attributes. Age distribution.
Process vessel characteristics in terms or residence time distribution
functions. Standard models based on plug flow, CSTR and dead space. Mixing
and age distribution. Application to reaction systems and liquid-liquid
extraction. Quantitative models: Diagnostics procedures. Signal flow graphs.
Reasoning with qualitative models.
51
Models for process simulation: Analysis of systems behavior for process
optimization, flexibility and safety. Stability and multiple states. Optimization
methods; Analytical/numerical techniques for single variable and multi variable
(constrained and unconstrained) functions; linear programming; PERT and
CPM project and its organization.
Recommended Books:
1. Taha Hamdy A. Operation Research-An Introduction Prentice Hall (Pvt)
Limited.
2. Edgar T. F., Himmelblau D.M. Optimization of Chemical Processes 1989
McGraw-Hill Inc.
3. B. V. Babu Process Plant Simulation, 2004 Oxford University Press.
4. E. Bruce Nauman, Chemical Reactor Design, Optimization and Scaleup,
2002 McGraw-Hill.
5. Robbin Smith, Chemical Process : Design and Integration, 2005, Wiley.
SEMESTER 8
Entrepreneurship
To provide and understanding of basic principles and concepts to analyze the
theories of entrepreneurship
Course Outline:
Introduction: The concept of entrepreneurship; The economist view of
entrepreneurship; The sociologist view; Behavioural approach;
Entrepreneurship and Management
The Practice of Entrepreneurship: The process of entrepreneurship;
Entrepreneurial Management; The entrepreneurial business;
Entrepreneurship in service institutions; The new venture.
Entrepreneurship and Innovation: The innovation concepts; Importance of
innovation for entrepreneurship; Sources of innovative opportunities; The
innovation process; Risks involved in innovation.
Developing Entrepreneur: Entrepreneurial profile; Trait approach to
understanding entrepreneurship; Factors influencing entrepreneurship; The
environment; Socio cultural factors; Support systems.
Entrepreneurship Organization: Team work; Networking organization;
Motivation and compensation; Value system.
Entrepreneurship and SMES: Defining SMEs; Scope of SMEs;
Entrepreneurial managers of SME; Financial and marketing problems of
SMEs.
Entrepreneurial Marketing: Framework for developing entrepreneurial
marketing; Devising entrepreneurial marketing plan; Entrepreneurial
52
marketing strategies; Product quality and design.
Entrepreneurship and Economic Development: Role of entrepreneur in
the economic development generation of services; Employment creation and
training, Ideas, knowledge and skill development; The Japanese experience.
Case Studies of Successful Entrepreneurs.
Recommended Books:
1. Paul Burns and Jim Dew Hurst: Small Business and Entrepreneurship
2. P. N. Singh: Entrepreneurship for Economic Growth
3. Peter F. Drucker: Innovation and Entrepreneurship Peter F. Drucker
4. John B. Miner: Entrepreneurial Success
ELECTIVE-II
ELECTIVE-III
PROCESS DESIGN & SIMULATION

Prerequisites: Engineering Thermodynamics.
To impart knowledge of the principles of process design and application of
simulation tools for synthesis of flow sheets for chemical processes.
Course Outline:
Hierarchy of process design; Process synthesis and design strategy. Pinch
design method. Heat and power integration. Reactor network design.
Separation system selection and design. Design of heat exchanger networks.
Optimization.
Introduction to various design and simulation software. Development of
process flow diagrams for various process industries and de-bottlenecking
using simulation software such as HYSYS/ASPEN. Economic evaluation of
processes. Strategies for decision making.
Lab Outline:
Recommended Books:
1. HYSYS (or Chem CAD) User and Tutorial Guides.
2. Chau, Pao C. Process Control: A First Course with MATLAB,
Cambridge University Press, 2002.
3. Davis, Timothy A. and Sigmon, Kermit, MATLAB Primer, 7th Ed.
Chapman & Hall/CRC, 2004.
4. Smith, R, Chemical Process Design and Integration 2005, John
Wiley & Sons.
53
DESIGN PROJECT- Part II
MAINTENANCE & UTILITY ENGINEERING

To equip students with the know-how of maintenance of process plants &
utilities handlings & operation
Course Outline:
Types of maintenance: Preventive, predictive and corrective, break down and
total productive maintenance. Individual versus group replacement; Internal
versus external maintenance. Scheduling and planning of maintenance.
Organization of maintenance force. Design considerations; Layout and
construction. Maintenance of rotary and stationery equipment, inspection
techniques; Non-destructive testing techniques. Lubrication and lubricants.
Importance of utilities in process industries, its types, selection criteria and
economical utilization. Flare network , Instrument & Plant Air, Boiler feed water,
Cooling water supply, Fire fighting system, Fuel gas supply, etc.
Recommended Books:
1. Maintenance Managers Standard Manual by Thomas A. Wester-Kamp,
Prentice-Hall.
2. A Guide to Effective Industrial Safety by Jack W. Boley, Gulf Publishing
Company.
ELECTIVES
COMPUTATIONAL FLUID DYNAMICS
Prerequisites: Fluid Mechanics-I, Fluid Mechanics-II.
To impart knowledge of the numerical solution of the comprehensive models
of chemical engineering operations based on the theories of momentum,
mass, and energy transport using commercial CFD packages.
Course Outline:
Scope and limitations of experimental, analytical and numerical methods in
transport processes. The Continuity Equation and governing equations for
Momentum, Heat and Mass transport in a continuum; The General Transport
Equation.
Discretization; basic concepts and methods. Discretized forms and solution
methodologies for steady and unsteady-state one-dimensional heat
conduction; Extension of discretization concepts to two- and three-
dimensional domains. Modeling of Convection and Diffusion terms using
54
various discretization schemes; Calculation of flow field using SIMPLE
algorithm.
Case studies: Simulation of various one- and two-dimensional laminar flow
situations covered in the course of Transport Phenomena using a CFD
software and comparison of results with analytical solutions.
Recommended Books:
1. Patankar. S. V., Numerical heat transfer and fluid flow, Hemisphere, 1980.
2. Versteeg, H. and Malalasekra, W., An Introduction to Computational Fluid
Dynamics: The Finite Volume Method, 2nd Ed., Prentice Hall, 2007.
MINERAL PROCESSING
To provide knowledge about art and science of beneficiating ores and minerals
with the aim to yield marketable value added products.
Course Outline:
Introduction to Mineralogy; Objectives of mineral processing. Mine-mill
interface. Properties of minerals and ores. Sampling and evaluation.
Comminution: fracture, liberation, size criteria, energy-size relationships.
Crushing and grinding. Screening and classifying. Concentration processes:
density and other physical processes. Interfacial phenomena. Flotation.
Liquid-solid separation: flocculation, thickening, filtration. Washability curves.
Partition curves. Material balances. Performance prediction. Applications
of biotechnology in mineral processing.
Recommended Books:
1. Jones, Meurig P., Applied Mineralogy: A Quantitative Approach, John
Wiley & Sons, 1987
2. Kelly, Errol G. and Spottiswood, David J., Introduction to Mineral
Processing, John Wiley & Sons, 1989
3. Wills, B. A., Mineral Processing Technology, Pergamon Press. 1985
NUCLEAR ENGINEERING
To acquaint students with the field of nuclear engineering.
Course Outline:
Role and importance of nuclear energy; Nuclear cross-sections; Reaction
Rates; Nuclear fission and chain reaction; Criticality conditions; Conversion
and breading; Reactor components and their characteristics; Classification
and design features of research, production and power reactors; Introduction
to fast and fusion reactor systems.
55
Different types of fuel cycles; Core and feedmaterial preparations; Uranium
enrichment; Fabrication of fuel; Reprocessing of Irradiated fuel; Fuel cycle
performance of commercially available reactors; In-core fuel management and
fuel management strategies.
Nuclear radiation hazards and nuclear waste management.
Recommended Book:
1. Lamarsh, J. R, Introduction to Nuclear Engineering, 3rd Edition, Prentice
Hall, 2001.
NOVEL SEPARATION PROCESSES

To impart knowledge about fundamentals, theory and design of Novel
separation processes.
Course Outline:
General theory of multistage separations based upon equilibrium and rate
processes. Theory, design and analysis of ion exchange processes along with
their industrial applications. Mass transfer processes through membranes:
separation of chemical species using osmosis, reverse osmosis, electro-
dialysis and molecular sieves. Adsorption, desorption and other surface
phenomena, design and operation of adsorption columns. Chromatographic
separation technology and its application to chemical and biochemical
separations.
Recommended Books:
1. Seader, J. D., and Ernest J. Henley. Separation Process Principles. New
York, NY: Wiley, 1998.
2. King, C. J. Separation Processes. 2nd Edition, New York, NY: McGraw-Hill,
1980
3. Manson Benedict, Nuclear Chemical Engineering, 2nd Edition, McGraw-
Hill, 1981
4. Treybal, R. E. Mass Transfer Operations. 3rd Edition, New York, NY:
McGraw-Hill, 1980.
SCIENCE OF ENERGETIC MATERIALS

To develop an understanding of chemistry and ballistics of propellants, primary
and high explosives and pyrotechnics.
Course Outline:
Propellants: Solid and liquid propellants, main families and use of solid
propellants, double base propellants, composite propellants, advanced
56
energetic binder propellants. Liquid mono and bi-propellants. Hybrid
propellants, safety characteristics and hazards, green propellant fuels.
Explosives: History of explosives and types of explosions, the chemistry of
explosives, deflagration, detonation and explosion, explosive classifications,
explosive initiation.
Pyrotechnics: Principles and applications of pyrotechnics, production of
noise, smoke, light, colour etc. Non-military applications of propellants and
explosives.
Recommended Books:
1. A. Bailey, G. S Murray Explosives, Propellants and Pyrotechnics
2. Alain Davenas, Solid Rocket Propulsion Technology Pergamon Press.
3. Urbanski, Chemistry and Technology of Explosives
ROCKET PROPULSION
To develop an understanding of theory and engineering of rocket propulsion,
basic design principles of solid and liquid rocket engines.
Course Outline:
Background and History of Rocket Propulsion, Classification, Applications,
Thrust, Exhaust Velocity, Energy and Efficiencies, Nozzle Theory and
Thermodynamic Relations, Chemical Rocket Propellant Performance
Analysis, Solid Propellant Rocket Fundamentals, Propellant Burning Rate,
Combustion Models, Basic Performance Relations, Propellant Grain and
Grain Configurations, Solid Propellant Classification, Propellant
Characteristics, Hazards, Propellant Ingredients, Propellant Processing and
Manufacture, Propellant Grain Mechanical Properties, Solid Rocket
Components and Motor Design, Introduction to Liquid Propellant Rocket
Engines, Liquid Propellants.
Recommended Books:
1. Elements of Rocket Propulsion; George P. Sutton, 7th Edition
2. Solid Rocket Propulsion Technology, Alain Davenas
3. Space Propulsion Analysis and Design; Humble, Hennry and Larson
4. Rocket Propulsion, M. Barriere
5. Modern Engineering for Design of Liquid Propellant Rocket Engines,
D. K. Huzel, D. H. Huang
EXPLOSIVE FORMULATION, MANUFACTURING & FILLING

To develop an understanding with manufacturing technologies of explosives
57
and energetic materials
Course Outline:
Manufacture of energetic materials, TNT, RDX, HMX, Tetryl, PETN, NC, NG,
Lead azide, Lead Styphnate etc. Formulation and filling of explosives,
casting, projectile preparations, Effects of casting, porosity, cavitation, crystal
size, uniformity of composition, standard casting procedures, pellet casting,
vacuum melting and casting, vibration and centrifugal casting, controlled
cooling and extrusion, Pressing, standard procedures and measurement of
explosive charges, direct pressing in casing, palletizing, vacuum pressing,
hot pressing, hydrostatic and iso-static pressing, machining of explosives,
quality controls in explosive charging, density, cracks, cavities, composition
variations.
Recommendation Books:
1. Paul Cooper, Explosive Engineering
2. A. Bailey, G. S Murray Explosives, Propellants and Pyrotechnics
3. Urbanski, Chemistry and Technology of Explosives
POLYMER ENGINEERING
To enhance the knowledge of polymers, their raw materials, processing
techniques, and uses.
Course Outline:
Detailed account of raw materials used; advanced treatment of methods of
polymerization and co-polymerization; principles of polymers formation;
thermal cleavage of covalent bonds; radical production by photochemical; high
energy radiation and oxidation-reduction processes; flow properties of
polymers, classification of melt flow behavior, rheological properties, structure
and properties of polymer; analysis and testing of polymers; production and
properties of commercially important polymers; detailed account of polymer
processing; design of equipment and machinery used; recent advances in
polymer technology.
Recommended Books:
1. Fried Joel R. Polymer Science and Technology, 2000, Prentice Hall.
2. Stanley Middlean, Fundamentals of Polymer Engineering, 3rd Edition,1996
3. Tim A. Ossworld, Georg Menges, Hanser Material Science of Polymer for
Engineering 2003.
4. I. M. Ward & D. W. Hadley, Wiley, An Introduction to the Mechanical
Properties of Solid Polymer, 3rd Edition, 1998
58
CHEMICAL WET PROCESSING OF TEXTILES
To impart knowledge of wet processing in textile industry
Course Outline:
Chemistry of textile processing; processes and machines for desizing,
scouring, bleaching and mercerization. Pretreatments; Application of reactive
vat and another classes of dyestuff on various machines. Dying of cotton,
viscous rayon and blend fibres. Printing, exposing print paste, pigment and
reactive types. thickening.
Rotary printing machine on curing process. Objective and service
performance of chemical finishing of soft and hard finishing agents. Printing
flexibility using CAD/CAM system; Treatment of effluent from Textile
Industry; Recovery of chemicals and their sustainable aspects.
Recommended Books:
1. Tyron. L. Vigo, Textile Processing and properties, 1994 Elsevier.
2. S. Kawabek, Objective Parameters of fabric, 1999, Textile Machinery
Society Kyoto.
3. E. R. Trotman, Hodder & Stoughton, Dyeing & Chemical Technology of
Textile Fibres, 1993 Charles Griffin & Co.
4. A. J. Hall, The Standard Handbook of Textiles, 2004, Wood head Publishing
Co.
PETROLEUM REFINERY ENGINEERING

To impart knowledge of processes and operations in petroleum refining
industry.
Course Outline:
Introduction; origin; formation and composition of petroleum; Indigenous and
world resources. Refinery products; properties; significant tests and
standard test methods; characterization and evaluation of crude oil stocks;
generation of crude processing data; Crude pre heating and preliminary
treatment; pipestill heaters; desalting; atmospheric and vacuum distillation;
steam stripping; arrangement of towers. Calculation of number of trays,
types of reflux employed; Packies approach; processing plans, schemes
and product patterns of refineries. Modern separation, conversion and
treatment processes. Thermal and catalytic cracking and reforming,
hydrocracking. Auxiliary processes and operations; refinery corrosion and
metals; blending plants, product design and marketing. Use of linear
programming techniques to solve refinery blending and production problems;
Overview of petroleum act.
59
Recommended Books:
1. W. L. Nelson, Petroleum Refinery Engineering, 1991, McGraw-Hill.
2. G. D. Hobson, Modern Petroleum technology, 1991, Applied Sc. Publisher.
3. J. H. Gary and G.E Handwerk, Petroleum Refinery Technology &
Economics, 2001, Dekker.
4. S. Parkash, Refining Processes Handbook, 2003, Elsevier/GPP.
GAS PROCESSING
To provide an understanding of the processes and operations in hydrocarbon
gas processing plants.
Course Outline:
Introduction to natural gas industry, gas production, testing of well fluid; Test
separator, Multiphase flow meters, establishing GOR; Gas-liquid separation
design and configurations. Acid gas sweetening; Chemical and Physical
solvent processes. Membrane/molecular sieve processes, Cryogenic
separation, solvent regeneration. Dehydration of Natural Gas, LPG recovery
and condensate stabilization, LNG and CNG. Gas processing facilities,
process flow schemes and product specifications.
Disposal of gas field emissions, effluent, produced water (EOR, Re-injection,
flaring) Design, metallurgy and corrosion protection of gas pipelines and
equipment. Sludge handling. Gas compression; compressors types, selection
between centrifugal and reciprocating compressor, design considerations.
Energy conservation in gas processing facilities. Flare system design; PSVs,
blow down, flare/vent stack sizing.
Recommended Books:
1. Ken Arnold, Maurice Stewart, Design of Gas Handling Systems and
Facilities, Volume 2, 1989, Gulf Publishing Company
2. Stephen A. Newman, Acid and Sour Gas Treating Processes,1985, Gulf
Publishing Company
3. Donald L. Katz , Handbook of Natural Gas Engineering,1990, McGraw-Hill
4. M. Saeed, Handbook of Natural Gas Transmission and Processing,
2006, Gulf Publishing Company
5. E. J. Hoffman, Membrane Separation Technology, 2003, Gulf Publishing
Company
6. GPSA Engineering Data Book 13th Ed. 2012, Gas Processors Supplier
Association.
7. Tarek Ahmed, Reservoir_Engineering_Handbook, 4E , 2010, Gulf
Professional Publishing.
8. Charles R. Smith, G. W. Tracy, and R. Lance Farrar, Applied Reservoir
Engineering, Vol 1 and Vol 2 Smith, Oil & Gas Consultants International.
9. Boyan Guo and Ali Ghalambor, Natural Gas Engineering Handbook, 2nd
Edition , 2005, Gulf Publishing Company
60
PETROCHEMICALS
To develop knowledge about unit operations and processes used for
production of valuable products from petroleum.
Course Outline:
Recent trends in Petrochemical industries. Hydrocarbon Sources and Raw
materials; their characterization, availability and pricing. Processes for the
production of ethylene, acetylene, and other monomers. Polymerization of
monomers into useful plastics.
Synthesis gas production, separation and purification, ammonia synthesis.
BTX production, separation and purification.
Recommended Books:
1. Austin George T. Shreves Chemical Processes Industries 6th Ed.
1997, McGraw-Hill International Edition.
2. Robert A. Meyers, Handbook of Petrochemical Production Processes,
2005, McGraw-Hill.
3. A. C. Waddems, Chemicals from Petroleum 978, John Murrey.
4. S. Strelzoff, Technology and Manufacture of Ammonia, 1982, Inter
Science Publishers.
5. Kirk Othmer, Encyclopedia of Chemical Technology, 1999, Intoosc
Publishers.
RISK MANAGEMENT & SAFETY

To provide understanding of plant safety by identifying risks, controlling and
managing them.
Course Outline:
Major hazard accidents; Basic concepts of risk; Hazard identification
procedures and techniques; What-if; HAZOP; FMEA. Consequence analysis
concerning release of chemical hazards including discharge models,
dispersion and effect models.
Fire and explosion models, effect models. Estimation of incident frequencies
(estimation of incident frequencies from historical data, frequency modeling
techniques, FTA and ETA).
Human factors in risk analysis; Risk of chemical reactions, e. g. chemical
reactivity and run away, active and passive safety in the design of equipment
and systems.
Emergency planning and responses; Storage and transportation of hazardous
61
materials. Introduction to International safety standards (e.g. OSHA etc.) A
specific case study
Recommended Book:
1. Fullwood R. R., Pobabilitistic Safety Assessment in Chemical and Nuclear
Industries. 1999.
INDUSTRIAL WASTE MANAGEMENT


To impart the knowledge about the sources of waste, its treatment and
disposal according to international/national standards, policies and regulations.
Course Outline:
Environmental Management; ISO 14001; EMAS; Environmental auditing;
Responsible Care; Environmental Policies and regulations. Different types of
eco- labeling.
Material Recycling: recycling of metals, recycling of polymeric materials.
Treatment of liquid waste streams: mechanical, biological and chemical
methods. Production of bio-gas. Anaerobic digestion and other stabilization
methods. Dewatering. Drying.
Treatment of solid waste: separation, incineration, composting. Separation;
Incineration. Other methods for disposal of solid waste (e.g. composting and
landfilling). Treatment and use of ash products. Treatment of radioactive
waste. Air and noise pollution and its control.
Recommended Book:
1. Cheremisinoff, Handbook of water and waste water treatment
technologies, 2002.
ENVIRONMENTAL ENGINEERING
To impart knowledge of environmental pollution, its control considering the
national and international standards, and its impact on environment and
ecology.
Course Outline:
Introduction to environment and ecology, pollution concept, types of pollution.
Environmental policy and standards; Environmental Monitoring (Air, Water &
Soil): Objectives of sampling and monitoring programme; Design and types
of samples; Pre-sampling requirements/information, sampling and design
purposes.
Air pollution control technologies, water pollution control technologies, water
62
treatment technologies, soil pollution control technologies, noise pollution
control technologies. Biotechnology for environment, industrial pollution
control; Occupational safety devices.
Principles and purposes of IEE and EIA and its significance for the society.
Cost and benefits of EIA. Main stages in EIA process. Public consultation
and participation in EIA process. EIA methods and techniques for impact
prediction and evaluation.
Recommended Book:
1. Cheremisinoff, Handbook of air pollution prevention and control, 2002.
RENEWABLE ENERGY RESOURCES

To provide in-depth knowledge of renewable energy resources and their
production to meet the energy needs of the country.
Course Outline:
Biomass Sources; Pretreatment of biomass for thermo-chemical conversion,
methods of production of fuels from biomass; Gasification and liquefaction of
forest products; Biomass volatilization; Pyrolytic reactions and products of
biomass; Kinetics of wood gasification; Characterization of peat and biomass
liquids; Fermentation to Ethanol and Biogas; Ethanol and Methanol
production; Social, economical, and environmental implications; Applied Solar
energy; Current status of wind and Tidal energy; Economics of Tidal power;
Wind turbines.
Recommended Books:
1. Overand R. P, Milne T. A, and Mudge L. K, Fundamentals of Thermo-
chemical Biomass Conversion, 1985, Elsevier Applied Science
publishers, NY, USA, ISBN 0 85334 306 3.
2. Palz W, Chartier P, and Hall D. O. Energy from Biomass, 1981,
Proceedings of First EC Conference, Applied sciences publishers Ltd.
London, UK, ISBN 0 85334 970 3.
3. Hobson P. N, Bousfield S, and Summers R, Methane production from
Agricultural and Domestic waste, 1981, Applied sciences publishers Ltd.
London, UK, ISBN 0 85334 924-X.
4. Report of National Research Council, Committee on Technology
Innovation, Board on Science and Technology for International
Development, USA, Alcohol Fuels-Options for Developing Countries,
1983, National Academy Press, Washington DC, ISBN 0309 03386 1.
5. Meinel B Aden, and Meinel P. Marjorie, Applied Solar Energy an
Introduction, 1976, Addison Wesley publishing Co. London, UK, ISBN 0
201 04719 5.
6. Roger Henri Charlier, Tidal Energy 1982, Van Nostrand Reinhold Co.
NY, USA, ISBN 0 442 24425 8.
7. Bhadra S. N, Kastha D, and Banerjee S, Wind Electrical Systems, 2005,
63
Oxford University Press, ISBN 0 195 67093 0.
INDUSTRIAL ENERGY SYSTEMS

To impart knowledge of energy systems in the process industry.
Course Outline:
Introduction to industrial process energy systems: concepts, heat balances,
heat distribution systems; local heating vs. central heating systems;
illustrative example from the pulping industry.
An overview of energy conversion technologies in industrial energy systems.
Process integration: Basics of process integration methodologies with
emphasis on Pinch analysis (Pinch temperature, minimum process heating
and cooling requirements, composite curves and grand composite curves,
targeting for minimum number of heat exchanger units). Design of heat
exchanger networks for maximum heat recovery. Process integration
principles for high-efficiency energy conversion technologies (heat pumps
and combined heat and power units) and energy-intensive chemical
separation operations (distillation, evaporation). Energy efficiency and
economic performance evaluation of process integration measures. Process
integration methodologies for retrofit applications in existing industrial energy
systems. Impact of reduced steam demand on electricity production for an
industrial process equipped with a steam turbine, CHP unit. Economics of
energy conversion in industrial energy systems: characteristics of heat
pumps and combined heat and power (CHP) units (performance, investment
costs). Influence of operating conditions on performance. Optimization of
size and various design parameters based on process integration principles.
Methodology for identifying the cost-optimal mix of technologies for satisfying
a process heat demand, accounting for heat load variation over the course of
the year.
Recommended Books:
1. Putman, R. E., Industrial Energy Systems: Analysis, Optimization, and
Control.
2. Smith, R., Chemical Process Design and Integration 2005, John
Wiley & Sons.
BIOCHEMICAL ENGINEERING
To develop an understanding of design and construction of unit processes
that involve biological organisms or molecules.
64
Course Outline:
Introduction to biochemical engineering; Enzyme Classification; Enzyme
reaction kinetics (Single-substrate Reactions) and energy patterns in
biological systems; Enzyme Inhibition; Non-ideal Enzyme Kinetics, Isolation
of enzymes and immobilized enzyme technology; Applications of Enzyme
Catalysis (Bio-catalysis); Transport phenomenon in microbial system; Design
and analysis of biochemical reactors (fermentors); Anaerobic and aerobic
metabolism photosynthesis and bio synthesis; biochemical and
microbiological applications.
Recommended Books:
1. Shuler, Michael L., and Fikret Kargi. Bioprocess Engineering: Basic
Concepts. 2nd Edition. Upper Saddle River, NJ: Prentice Hall PTR, 2001.
2. Blanch, Harvey W., and D. S. Clark, eds. Biochemical Engineering. New
York, NY: Marcel Dekker Incorporated, 1997.
3. Bailey, James E., and David F. Ollis. Biochemical Engineering
Fundamentals. 2nd Edition, McGraw-Hill, Inc., New York, 1986.
4. Lovitt, R., and Jones, M. Biochemical reaction engineering, Coulson and
Richardsons Chemical Engineering, Richardson, J.F., and Peacock, D.G
(Eds.), 3rd Edition, Vol-3, Pergamon Press, London. 1994.
5. Levenspiel, O. Chemical Reaction Engineering. 3rd Edition 2006, John
Wiley & Sons.
BIOCHEMICAL SEPARATIONS
To study the techniques involved in the purification, or recovery, of product
obtained through biochemical reactions.
Course Outline:
Introduction to the fundamental principles of separation operations for the
recovery of products from biological processes; Mass transfer coefficients;
Supercritical fluids. Flocculation and coagulation. Membrane filtration,
chromatography, centrifugation, crystallization, drying, cell disruption.
Protein refolding, extraction. Process design for recovery of products from
biological processes. Application of bio-technology to energy conversion, solid
waste and water treatment etc.
Recommended Books:
2. Lovitt, R., and Jones, M. Biochemical Reaction Engineering, Coulson and
Richardsons Chemical Engineering, Richardson, J.F., and Peacock, D.G
(Eds.), 3rd Edition, Vol-3, Pergamon Press, London. 1994.
3. Tutunjian, R. S. "Ultrafiltration Processes in Biotechnology." In
Comprehensive Biotechnology. Vol. 2, The Principles of Biotechnology:
Engineering Considerations. Edited by C. L. Cooney, and A. E.
65
Humphrey. Elmsford, NY: Pergamon Press Ltd., 1985.
BIOCHEMICAL PROCESSES AND PRODUCTS

To apply the knowledge in biochemical engineering to develop processes and
products.
Course Outline:
Application of biotechnology in Chemical Industry: Bio-degradation; Bio mass
productivity and activity; Aerobic and anaerobic processes; Bio-chemical
processes involved in the production of food products, beverages, organic
acids, industrial solvents, various pharmaceutical products and antibiotic and
commercial enzymes. Fermentation Industries: Industrial alcohol, Biodiesel
and industrial solvents. Biodegradable Plastics and other related products.
Treatment of waste from food and pharmaceutical Industry; Bio-remediation;
Food preservation; Health hazards; Hygiene and sanitation. Important food
industries in Pakistan. Food legislation: Concept and significance; Food
legislation in Pakistan in relation to international laws. Bio-safety regulations
Recommended Books:
2. Austin George T. Shreves Chemical Processes Industries. 6th Ed.,
McGraw Hill International Edition. 1997
3. Kirk Othmer Encyclopaedia of Chemical Technology. Inter Science
Publishers. 1999.
4. Government of Pakistan. Prospects of Chemical Industry in Pakistan
2003, Export Advisory cell, Ministry of Industries and Production,
Islamabad.
PRODUCTION & OPERATIONS MANAGEMENT

To familiarize students with the techniques of management
Course Outline:
Introduction to Evaluation of Management Science: Entrepreneurship, SMEs.
Nature & scope of Operation Management: Introduction to production
management functions and classification of production systems. Production
Operation Strategies, Goals tactics and mission.
Decision Making: The decision process, characterization of operation decision
; General approach to decision making. Decision Environmental; Decision
Models. Resource Allocation- Linear Programming: Model Formulation Types/
Classification of Models; Analysis of linear programming model, Graphics
approach, Simplex method, Application of linear programming.
66
Forecasting: Forecasting Environments & their modeling. Design of Work
System: Facilities layout basic types, line balancing, Waiting Lines Goal,
measuring system performance Quening Models Infinite Source, Finite
Source. Reliability & Liability. Product Life Cycle. Process selection & capacity
planning; Breakeven Analysis, Linear & Non-Linear. Cost volume analysis.
Capacity Management: the meaning of capacity; Capacity planning; Inventory
Management/types & EOQ model, quantity Discount models.
Project Management: PERT CPM Analysis, Queuing Analysis/waiting lines
Recommended Books:
1. Bufa e. S., (1980), Elements of Production: Operations Management,
New York: John Wiley & Sons.
2. Stevenson, W.J., (1986), Production operation Management, 8th Edition.
3. Chase Richard B. Aquilano, Nicholas, J. (1973), Production of operations
management: a lifecycle approach. Homewood, III: R. D. Irwin.
4. Stevenson W.J., (2005), Production operations Management, 8th Edition,
McGraw-Hill Irwiv.\
5. John V. C. Lawrence R. P. Reavil A. C. Payne (2004), Management of
Engineers, Scientists & Technologists, 2nd Edition, Wiley & Son
67
SOCIAL SCIENCES & MANAGEMENT COURSES
SOCIAL SCIENCES COURSES
ENGINEERING ECONOMICS

To familiarize students with the concepts of economics and their application
in chemical engineering design for the purpose of cost estimation and
profitability analysis.
Course Outline:
Engineering economy defined; Measures of financial effectiveness; Non-
monetary factors and multiple objectives; principles of engineering economy.
Consumer and producer goods; Measures of economic worth; Price, Supply
and demand relationship; Production; Factors of production; Laws of return.
Sunk and opportunity costs; Fixed, variable, and incremental costs; Recurring
and non-recurring costs; Direct, indirect, and overhead costs; Standard costs;
Breakeven analysis; Unit cost of production; Cost-benefit analysis; Feasibility
studies; Value analysis in designing and purchasing.
Islamic and Contemporary financing system and their use in cost estimation.
Depreciation accounting.
Economic evaluation of processes and equipment; Payback period method;
Present worth method; Uniform annual cost method; Rate of return method.
Manufacturing lead time; Production rate; Capacity; Utilization; Availability;
Work in process; WIP and TIP ratios.
Types of ownership; Types of stock; Partnership and joint stock companies;
Banking and specialized credit institutions.
Recommended Books:
1. Leland Blank, and Anthony Tarquin, Engineering Economy, 6th
Edition, McGraw-Hill, 2005
2. G. J. Thuesen, and W. J. Fabrycky, Engineering Economy, 9th
Edition, Prentice Hall of India, 2005.
3. Ted G. Eschenbach, Engineering Economy, 2nd Edition, Oxford
University Press, 2003.
4. James L. Riggs, David D. Bedworth, and Sabah U. Randhawa,
Engineering Economics, 4th Edition, Tata McGraw-Hill, 1996.
5. James L. Riggs, and Thomas M. West, Essentials of Engineering
Economics, 2nd Edition, McGraw-Hill, 1986.
68
SOCIOLOGY AND DEVELOPMENT
To apprise potential engineers about social factors that contribute towards
enhancing their professional performance for the good of society and the
country.
Course Outline:
Introduction to Sociology
What is sociology? Nature, scope, and importance of sociology, social
interactions, social groups, social institutions.
Culture and Related Concepts
Definition of culture, types of culture, elements of culture, role of culture in
organization, socialization and personality.
Interpersonal Relations
Interpersonal behaviour, formation of personal attitudes, language and
communication, motivations and emotions, public opinion.
Social Stratification
Factors of social stratification, caste and class, power, prestige, and authority,
social mobility, migration.
Human Ecology
Ecological processes, ecosystem andenergy, ecosystem and physical
environment, solid waste disposal, pollution.
Population Dynamics
World population growth and distribution, population dynamics in Pakistan,
causes and consequences of urbanization, population policy in Pakistan,
population and development.
Community Development
Meaning, scope, and subject matter of community development, processes of
community development, community development programs in Pakistan,
community organization and related services, cooperation and conflict in
community development.
Deviance and Crime
Crime as a social and cultural phenomenon, crime and social organization,
organized crime, culture based crime, economics of crime.
Sociology of Change and Development
What is social change and development? dynamics of social change, role of
NGOs in development; World system and development, gender and
development.
Recommended Books:
1. Allport, G. W. (1985). The Historical Background of Modern Social
Psychology. New York, Random House.
2. Bernard, A. and T. Burgess (2004). Sociology. Cambridge University
69
Press.
3. DuBrin, A. J. (2007). Human Relations: Interpersonal Job Oriented Skills.
New York, Prentice Hall.
4. Gardezi, H. N., Ed. (1991). Understanding Pakistan: The Colonial
Factor in Societal Development. Lahore, Maktaba Fikr-o-Danish.
5. Hafeez, S. (1991). Changing Pakistan Society. Karachi, Royal Book
Company. Gardezi, H. N., Ed. (1991).
6. Jones, G. W. (2005). "Why are Population and Development Issues not
Given Priority?" Asia-Pacific Population Journal 20(1).
7. Macionis, J. J. (1999). Sociology 7th Edition, National Book Foundation,
Islamabad
8. Maser, C. (1997). Sustainable Community Development: Principles and
Concepts. Plorida St. Lucie Press.
9. Nelson, N. and S. Wright (1995). Power and Participatory Development:
Theory and Practice. London, Intermediate Technology Publications.
10. Syed, S. H. (2003). The State of Migration and Multiculturalism in
Pakistan: The Need for Policy and Strategy. Islamabad, UNESCO: 1-30.
11. Utton, A. E. (1976). Human Ecology, West View Press.
12. Webster, A. (1990). Introduction to Sociology of Development. London,
Macmillan Education Ltd.
13. Weiss, A. M. (2001). Power and civil society in Pakistan, Oxford
University press.
SOCIAL ANTHROPOLOGY
To provide understanding of anthropological skills for application by
professional engineers and other related practitioners.
Course Outline:
I Introduction
1. Anthropology and social anthropology
2. Fields of anthropology
3. Anthropological research methods
4. Social anthropology and other social sciences
5. Significance of social anthropology
II Culture
1. Definition, properties and taxonomy
2. Evolution of growth and culture
3. Evolution of man: Religious and modern perspectives
4. Evolution of culture
5. Culture and personality
III Evolution and Growth of Culture
1. Evolution of man
2. Schools of thought in cultural anthropology
70
3. Acculturation
4. Enculturation
5. Ethnocentrism and xenocentrism
IV Language and Culture
1. Communication
2. Structural linguistics
3. Historical linguistics
4. Relationship between language and culture
5. Ethnography
V Economic System
1. Global economic system
2. The allocation of resources
3. The conversion of resources
4. The distribution of goods and services
5. Poverty and inequality
VII Marriage and Family
1. Marriage and mate selection
2. The family: Types and functions
3. Kinship system
4. Structure and function of family
5. Gender Relations
VIII Political Organization
1. Political sociology
2. Origin of political organization and organizational system
3. Types of political organizations
4. Power politics and factionalism in Pakistan
5. Resolution of conflict
IX Religion and Magic
1. The universality of religion
2. Comparative religions
3. Religion and society
4. Religious beliefs and practices
5. Witchcraft and sorcery
XI Culture Change
1. Forms of art
2. Expressive culture
3. Process of cultural change
4. Cultural change in the modern world
5. Cultural change in Pakistani society
Recommended Books:
1. Ahmad, Akbar S. 1990. Pakistani Society, Karachi, Royal Books Co.
2. Bernard, H. Russel. 1994. Research Methods in Anthropology,
Qualitative and Quantitative Approaches. London: Sage Publications
3. Bodley, John H. 1994. Cultural Anthropology, California: Mayfield
71
Publishing Co.
4. Brogger, Jan. 1993. Social Anthropology and the Lonely Crowd. New
Delhi: Reliance Publishing
5. Ember, Carol R. & Ember Melvin. 2005. Anthropology, 11th Ed.
Englewood Cliffs: Prentice Hall, Ince. Harper and Row
6. Harris Marvin. 1987. Cultural Anthropology. New York: Harper and Row
7. Harris Marvin. 1985. Culture, People, nature; An Introduction to General
Anthropology London: Harper and Row
8. Haviland, W. A. (2005). Anthropology: The Human Challenge. New York,
Thomson Learning Inc.
9. Hertzler J. O. 1981. The Social Structure of Islam. Cambridge: Cambridge
University Press.
10. Keesing, Roger M. 1998. Cultural Anthropology: A contemporary
perspective. 3rd ed. New York: Harcourt Brace College Publishers.
11. Kottak, Conard Phillip. 2002. Anthropology: The Exploration of Human
Diversity. 9th Ed. Boston: McGraw-Hill Higher Education.
12. Kennedy, Charles H. 1992. Pakistan London: Westview Press,.
13. Marron, Stanley. 1057. Pakistani Society and Culture. New Heaven
14. Wilson, Richard A. 1996. Human Rights, Culture and Context:
Anthropological Perspective. London: Pluto Press.
UNDERSTANDING PSYCHOLOGY AND HUMAN BEHAVIOUR

To provide an understanding of human psychology and behaviour.
Course Outline:
- What is psychology?
- Nature, scope and application with special reference to Pakistan
- Different schools of psychology
- Methods of psychology
- Learning
- Intelligence and artificial intelligence
- Personality and its assessment
- Understanding mal-adjective behaviour
- Positive emotional states and processes
- Stress management and anger management
Recommended Books:
1. Atkinson R. C., Smith E. E. (2000), Introduction to Psychology (13th
Ed.), Harcourt Brace College Publishers. Fernald, L. D., & Fernald, P. S.
(2005), Introduction to Psychology, USA: WMC Brown Publishers.
2. Hergenhahn, B. R. (2001). An Introduction to the History of Psychology,
New York: Wadsworth.
3. Goodwin, C. J, (2000) Research in Psychology: Methods and Design,
(3rd E), New York: John Wiley & Sons.
4. Synder, C. R., Lopez, S. J. (2007) Positive Psychology, USA, Sage
72
Publications.
5. Allen, B. P. (1997), Personality Theories: Development, Growth and
Diversity, (2nd Ed.), Boston: Allyn & Bacon.
6. Cohen, R. J., Swerdlik, M. E. (2005) Psychological Testing &
Assessment (6th Ed.), New York: McGraw-Hill.
7. Corcini, R., (2000). Current Psychotherapies. London: Thompson & Co
Publishers.
8. Comer, R. J. (2004). Abnormal Psychology, USA: Freeman & Company.
9. Schwartz, B., Wassernman, E., Robbins, S. (2002), Psychology of
Learning and Behaviour, 5th Ed. Norton and Company.
PROFESSIONAL PSYCHOLOGY

To provide understanding of human psychology in the context of technical
organizations and work environment.
Course Outline:
- Introduction to professional psychology
- Psychological testing
- Educational psychology
- Industrial/organizational psychology
- Social psychology
- Health psychology
- Clinical psychology
- Positive psychology
- Legal, ethical, and professional issues.
Recommended Books:
1. Crow, L., & Crow, A. (2000) Educational Psychology, New Delhi:
Eurosia Publishing House Ltd.
2. Spiegel, P.K., Koocher, G.P. (1998), Ethics in Psychology, New York:
Oxford University Press
3. Snyder, C. R., Lopez, S. J. (2000), Handbook of Positive Psychology,
New York: Oxford University Press.
4. Compton, W. C. (2005), Introduction to Positive Psychology, USA,
Thomson Wadsworth.
5. Debra, L. N. James Compbell Quick, (2000) Organizational Behaviour
(3rd Ed), Cincinnati: South Western.
6. Fred Luthans, Alexander, D. S. Edwin, A. Locke (2000) (Eds),
Handbook of Principles of Organizational Behaviour, London: Blackwell.
7. Brannon, L. Reist, J. (2000), Health Psychology: An Introduction to
Behaviour and Health (4th Ed.), USA Wadsworth.
8. Donohue, W. Ferguson, K. (Eds), (2003), Handbook of Professional Ethics
for Psychologists; Issues, Questions and Controversies, London: Sage
Publications.
9. Meyers, D. (2005), Social Psychology, 8th Ed. McGraw-Hill Inc.
73
10. Cooper, J. Hogg, M. (2003) Handbook of Social Psychology, Sage
Publications
11. Halgin, R. P., Whitbourne, S. K., Halgin, R. (2004), Abnormal
Psychology: Clinical Perspectives on Psychological Disorders, New York:
McGraw-Hill.
12. Thorndike R. L., Hage, E. P. (1995), Measurement and Evaluation in
Psychology and Education (4th Ed), New York, McMillan.
Organizational Behaviour
To provide an understanding of organizational behaviour
Course Outline:
Introduction to organizational behaviour Organizational disciplines and
topics Psychological perspective
o Social-psychological perspectives
Structure and control in organization
o Introduction
o Bureaucracy
o Managerial work
o Contingency theory
o Organizational design
Individual and work learning
o Learning theories
o Learning and work
Stress
o Types of stress and work
o Occupational stress management
Individual differences
o Personality and its factors
o Personality dimensions and social learning
Intelligence
Motivation and job satisfaction
o Needs at work
o Theories of motivation and job satisfaction
o Correlates of job satisfaction
o Correlates of job satisfaction
Group and work
o Social interaction
o Dramaturgy and impression management
o Social skill
Group and inter-group behaviour
o Group structure and norms
o Group processes
o How throne studies
74
Leadership
o Leadership as an attribute
o Leadership style
Patterns of work
o Work-the classical approach
o Marx, Weber, and the critique of labor
o Foucault and disciplinary power
Conflict and consent in work
o The labour process debate
o Work place control and resistance
o Industrial conflict and industrial relations
Organizational culture
o Organizational culture and strategic management
o Exploring organizational culture
o Evaluating concept of culture
Recommended Books:
1. Finchan, R., Rhodes, P. (2003), Principles of Organizational
Behaviour, 3rd Oxford.
2. Noe, R., Hollenbeck, J. Gerhart, B., Wright, P. (2006), Human
Resource Management, 5th Ed., McGraw-Hill.
3. Newstrom John W. (2007), Organizational Behaviour, (12th Ed), McGraw-
Hill.
4. Luthan Fred, (2005), Organizational Behaviour, McGraw-Hill Inc.
5. Robins, Stephen, (2005), Organizational Behaviour, McGraw-Hill Inc.
INTRODUCTION TO SOCIOLOGY
To provide an understanding of basic principles and concepts relating to
sociology
Course Outline:
The Nature of sociology
o The study of social life
o Exploring the global village
o Sociology as a science
o The sociological imagination
o The development of sociology
o Pioneers of sociology
o Nature, scope and subject matter of sociology
o Brief historical development of sociology
o Society and community
o Relationship with other social sciences
o Social interaction processes
75
Social groups
o Definition and functions
o Types of social groups
Social institutions
o Definition
o Structure and function of social institutions
o Inter-relationships among various social institutions
Culture and related concepts
o Definition and aspects of culture
o Elements of culture
o Organization of culture
o Other concepts, cultural relativism, sub cultures, ethnocentrism,
culture lag
Socialization and personality
o Role and status
o Socialization
o Culture and personality
Deviance and social control
o Definition and types of deviance
o Juvenile delinquency
o Formal and information methods of social control
Social stratification
o Approach to study social stratification
o Caste class and race as basics of social stratification
Major perspectives in sociology
o Functionalist perspective
o Conflict perspective
o Interactionistic perspective
Social control and deviance
o Agencies of social control
Social stratification
o Determinants of social stratification
o Social mobility, types and definition
o Dynamics of social mobility
Concept of social movement
o Theories of social movement
o Social and cultural change
Social and cultural change
o Definition of social change
o Dynamics of social change
o Impact of globalization on society and culture
o Resistance to change
Collective behaviour
o Definition
o Characteristics
76
o Causes
o Types
o Social movements
o Mob and crowd behaviour
Recommended Books:
1. Neulreck, Kenneth, J. 2005, Sociology: Diversity, Conflict and Change,
Boston
2. Barnard, Andy. 2004. Sociology, Cambridge University Press
3. Giddens, Anthony, 2004, Sociology 4thEdition, Cambridge Polity Press
4. Albrow, Martin, 2003, Sociology, London Routledge.
5. Richard, T. Schaefer, 2003, Sociology 5th Edition, McGraw-Hill College
6. Kendall, Diana, 2004. Sociology in our Times, 4th Ed, Wadsworth
7. Tyler Melissa, Wallace Claire & Abbott Pamela, 2005, An
Introduction to Sociology, 3rd Ed. Routledge.
LOGICAL & CRITICAL THINKING

To provide an understanding of basic principles and concepts relating to logical
and critical thinking.
Course Outline:
The Power of critical thinking
o Claims and reasons
o Reasons and arguments
o Arguments in the rough
The Environment of critical thinking
o Perils of haunted mind
o Self and the power of the group
o Subjective and social relativism
o Skepticism
Making sense of arguments
o Arguments basics
o Patterns
o Diagramming arguments
o Assessing long arguments
Reasons for belief and doubt
o Conflict experts and evidence
o Personal experience
o Fooling ourselves
o Claims in the news
Faulty reasoning
o Irrelevant premises
o Genetic fallacy, composition, division
o Appeal to the person, equivocation, appeal to popularity
o Appeal to tradition, appeal to ignorance, appeal to emotion
o Red herring, straw man
77
Unacceptable premises
o Begging the question, false dilemma o Slippery slope, hasty
generalization o Faulty analogy
Deductive reasoning: Propositional logic
o Connectives and truth values
o Conjunction, disjunction, negation
o Conditional, checking for validity
o Simple arguments, tricky arguments
o Streamlined evaluation
Deductive reasoning: Categorical logic
o Statements and classes
o Translations and standard form
o Terms, quantifiers
o Diagramming categorical statements
o Sizing up categorical syllogisms
Inductive reasons
o Enumerative induction
o Sample size, representativeness, opinion polls
o Analogical induction
o Casual arguments, testing for causes
o Casual confusions
Inference to the best explanation
o Explanations and inference
o Theories and consistency
o Theories and criteria
o Testability, fruitfulness, scope, simplicity
o Conservatism
Judging scientific theories
o Science and not science
o The scientific method, testing scientific theories
o Judging scientific theories
o Copernicus versus Ptolemy, evolution versus creationism
o Science and weird theories
o Making weird mistakes
o Leaping to the weirdest theory, mixing what seems with what is
o Misunderstanding the possibilities
o Judging weird theories
o Crop circles, talking with the dead
Recommended Books:
1. Vaughn Lewis, 2005, The Power of Critical Thinking, Oxford University
Press.
2. Paulsen David W., Cederblom Jerry: 2000, Critical Reasoning,
Wadsworth
3. Restall Greg. 2005, Logic: An Introduction, Routledge
78
INTRODUCTION TO PHILOSOPHY

Course Outline:
Definition and nature of philosophy
Theory of knowledge
o Opinion and knowledge
o Plato, the republic selection
o Knowledge through reason
o Descartes meditation on first philosophy
o Knowledge through experience
o Hume an Inquiry concerning human understanding (Selection)
o Experience structured by the mind
o Kant critique of pure reason (Selection)
o Knowing and doing
o James pragmatism (Selection)
o Knowledge and emotion
o Jaggar love and knowledge (Selection)
Philosophy of religion
o Proving the existence of God
o Anselm, Aquinas, Paley, Dawkins (Selection)
o Justifying religious beliefs
o Pascal Pensees (Selection)
o James The will to believe selection
o Freud The future of an illusion (Selection)
o Confronting the problems of evil
o Mackie Evil and omnipotence (Complete)
o Hick Philosophy of religion (Selection)
Metaphysics
o Idealism and materialism
o Berkeley Three dialogues between Hylas and Pholonous (Selection)
o Armstrong Naturalism, materialism and first philosophy (Selection)
o The mid-body problem
o Descartes Meditations on first philosophy (Selection)
o OHear Introduction to the philosophy of science (Selection)
o Dennett The origins of selves (Complete)
o Pali Canon (Selection)
o Penelhum Religion and rationality (Selection)
Freedom to Choose
o Libertarianism
o James The dilemma of determinism (Selection)
o Taylor Metaphysics (Selection)
o Determinism
o Hospers Meaning and free will (Selection)
o Skinner Walden Two (Selection)
o Compatibilism
o State Religion and the modern mind (Selection)
79
o Radhakrishnan Indian philosophy (Selection)
Ethics
o Fulfilling Human Nature
o Aristotle Nicomachean Ethics (selection)
o Loving God
o Augustine The Morals of the Catholic Church and the City of
God (Selection)
o Following Natural Law
o Aquinas Summa Theologiae (Selection)
o Doing Ones Duty
o Kant Fundamental Principles of the Metaphysics of Morals (Selection)
o Maximizing Utility
o Mill Utilitarianism (Selection)
o Turning Values of Upside Down
o Nietzsche Human, All too Human and Beyond Good and Evil
(Selection)
o Creating Ourselves
o Sartre Existentialism is a Humanism (Selection)
o Hearing the Feminine Voice
o Gilligan In a Different Voice (Selection)
o Baier What do Women Want in a Moral Theory (Selection)
Political and Social Philosophy
o The State as Natural
o Plato the Republic (Selection)
o Aristotle Politics (Selection)
o The State as a Social Contract
o Hobbes Philosophical Rudiments Concerning Government and
Society (Selection)
o Locke the Second Treatise of Government (Selection)
o Liberty of the Individual
o Mill On Liberty (Selection)
o Alienation in Capitalism
o Marx Economic and Philosophic Manuscripts of 1844 (Selection)
o Justice and Social Trust
o Rawls A Theory of Justice (Selection)
o Nozick Anarchy, State, and Utopia (Selection)
o Held Rights and Goods (Selection)
o Women in Society
o Wollstonecraft A Vindication of the Rights of Women (Selection)
o De Behaviour The Second Sex (Selection)
o The Value of Philosophy
o Russel The Problems of Philosophy (Selection)
o Midgley Philosophical Plumbing (Selection)
Recommended Books:
1. Abel Donald C., Stumpf Samuel Enoch, 2002. Elements of Philosophy:
An Introduction, 4th Ed. McGraw-Hill.
2. Scruton Roger, 2001. A short History of Modern Philosophy, 2nd Ed.
Routledge.
80
MANAGEMENT COURSES
Principles of Management
To provide an understanding of the fundamental principles of management
and of managing people and organization in a historical as well as
contemporary world.
Course Outline:
Introduction, overview and scope of discipline
The evolution and emergence of management thought
Management functions
Planning concepts, objectives, strategies and policies
Decision making
Organizing; departmentalization, line/staff authority, commitments and
group decision making
Staffing: principles of selection, performance, career planning
Leading: Motivation, leadership, communication
Controlling: the system and process and techniques of controlling
Management and Society: future perspective
Recommended Books:
1. Stephen P. Robins, Mary Coulter: Management
2. H. Koontz Odonnel and H. Weihrich: Management
3. Mc Farland: Management: Foundation and Practice
4. Robert M. Fulmer: The New Management
INDUSTRIAL MANAGEMENT
To provide understanding of the principles and techniques of industrial
management
Course Outline:
Introduction to Industrial Management; Productivity, Plant Layout; Product and
Process layout analysis and comparison; Material handling considerations in
layout; Production planning methods, material requirement planning, material
resource planning. Capacity planning and control; Production control systems;
Job shop scheduling; Quality Control; Production control charts; Scheduling
techniques; Purchasing and procurement; Inventory control; EOQ/EPQ
models; Time and Motion study.
Organizational structure; Human resource management; Project
81
management principles; PERT/CPM; Total quality management; ISO
standards; Labour and engineering laws; Labour problems; Labour
organizations; Prevention and settlement of disputes.
Recommended Books:
1. Harold Kerzner, Project Management: A Systems Approach to Planning,
Scheduling, and Controlling, Ninth Edition, John Wiley & Sons, 2006.
2. Jay Heizer and Barry Render, Principles of Operations Management,
Third Edition, Prentice Hall, 1999.
3. Jay Heizer and Barry Render, Operations Management, Fifth Edition,
Prentice Hall, 2000.
4. Industrial Management Methods. Ronald Hurst.
5. Industrial Organization & Management. BETHEL.
6. Principles of Management Design. Robert E. Parr.
82
ME/MSc. (Engg) CHEMICAL ENGINEERING
This program aims to provide in-depth knowledge of Chemical Engineering
to enhance analytical skills and research capabilities of the candidates.
The program will prepare chemical engineers for careers in teaching,
research and development, and management in academia, government, and
industry. This program shall also provide a basis for continued study leading
to PhD degree.
Eligibility Criteria:
The committee determined the eligibility of the candidates seeking admission
to the degree of ME/MSc. (Engg.) in Chemical Engineering and recommended
that:
Bachelors Degree in Chemical Engineering or equivalent from a
recognized University should be the minimum requirement for eligibility of a
candidate seeking admission to the degree of MS/ME/MSc. (Engg.) in
Chemical Engineering.
Degree Requirements:
The committee determined the requirements for the award of degree of
ME/MSc. (Engg.) in Chemical Engineering and recommended that the
ME/MSc. (Engg.) in Chemical Engineering course shall comprise of:
1. A minimum of thirty (30) credit hours of course work or a minimum of twenty
four (24) credit hours of course work along with a minimum of six (6)
credit hours of research work/thesis.
2. A minimum of one academic year for full-time students or two academic
years for part-time students.
3. The minimum number of teaching weeks per semester shall be sixteen.
4. Candidates should be evaluated during the session through tests, quizzes
and assignments followed by a comprehensive examination at the end
of each semester.
Framework ME/MSc Chemical Engineering

This program is built around:
a minimum of 12 credit hours of course work from the core chemical
engineering courses, and
a minimum of 12 credit hours of course work from elective courses
a minimum of 6 credit hours of research work, preferably resulting in
a publication in peer reviewed journal/conference.
LIST OF ME/MSc. (Engg.) COURSES
LIST OF CORE COURSES:
(Select any 04 courses; Advanced Engineering Mathematics is compulsory)
1 . Advanced Chemical Engineering Thermodynamics Advanced Chemical
83
Reaction Engineering
2. Advanced Transport Phenomena
3. Advanced Engineering Mathematics
4. Process Dynamics and Control
5. Advanced Separation Processes
LIST OF ELECTIVE COURSES:

Group 1: Design Engineering:
1. Advanced Chemical Reactor Design
2. Advanced Fluid Mechanics
3. Advanced Heat Transfer
4. Numerical Methods in Chemical Engineering
5. Design of Heat Recovery Systems
6. Particle Dynamics
7. Experimental Design and Analysis
8. Project Management
Group 2: Process Engineering

1. Biochemical Engineering
2. Computational Fluid Dynamics
3. Computer Aided Process Design
4. Occupational Health and Safety in Process Industries
5. Process Design and Optimization
6. Transport Processes
7. Process Modeling and Control
8. Process Safety and Loss Prevention
Group 3: Energy Engineering
1. Sustainable Energy Engineering
2. Environmental Engineering
3. Energy Management & Auditing
4. Power Plant Engineering
5. Coal Technology
Group 4: Energetic Materials
1. Polymer Engineering
2. Explosives and Propellants
3. Rocket Propulsion Technology
4. Combustion of Energetic Materials.
Group 5: Advanced Materials
1. Advanced Composite Materials
2. Nano Technology
3. Materials Engineering
4. Mechanical & Thermal Behaviour of Materials
84
Other elective subjects may also be included according to the
specialization/availability of the faculty and the facilities.
Students may undertake up to two relevant elective courses from other
Academic Departments of the same Institution or from any other Academic
Institution of Pakistan.
DETAIL OF COURSES
FOR ME/MSc IN CHEMICAL ENGINEERING
The proposed course contents are recommended to be offered as part of
three credit hour courses.
Group 0; Core Engineering Courses
ADVANCED CHEMICAL ENGINEERING THERMODYNAMICS:
Advanced topics in thermodynamics with emphasis on chemical and physical
equilibria, and the estimation of thermodynamic properties. Methods of
treating chemical and phase equilibria in multi-component systems through
the application of thermodynamics and molecular theory.
ADVANCED CHEMICAL REACTION ENGINEERING:
Review of fundamental principles; Order of reaction and rate equation;
Theory of rate processes; Diffusion and types of reactors; Estimation of
reaction rate parameters using empirical and quantum chemical methods,
detailed chemical kinetic modeling. Design of chemical reactors for
homogeneous and heterogeneous reactions; Analysis and comparison of
the differences between batch and continuous reactor by using kinetics and
mass, energy and momentum balances. Design of fixed-bed, fluidized-bed
and industrial catalytic reactors.
ADVANCED TRANSPORT PHENOMENA:
Advanced treatment of conductive heat transfer and convective heat and
mass transfer. Use of boundary conditions to obtain solutions in particular
situations. Interfacial phenomena. Simultaneous heat and mass transfer.
Turbulence and its measurements. Statistical approach to turbulent flow.
Mathematical model of turbulence. Applications of continuity and Navier-
Stokes equations of particular situations. Solutions of boundary layer
equations. Application to equipment design. Transfer through membranes and
transpiration cooling.
ADVANCED ENGINEERING MATHEMATICS:
Application of advanced mathematical techniques to chemical engineering
analysis. Mathematical modeling, scaling, regular and singular perturbation,
multiple scales and asymptotic analysis. An introduction to modeling of
Chemical Engineering problems. Formulation and classification of partial
differential equations. Finite difference approximation. Method of
characteristics. Formulation of boundary conditions and treatment of non
linearities. Coupled equations. Application of the above principles in
85
chemical engineering problems including linear and nonlinear ordinary
differential equations and partial differential equations.
PROCESS DYNAMICS & CONTROL:
Fundamentals of mathematical modeling; Modeling and simulation of
chemical processes. Transient response of control systems. Frequency
response analysis. Root locus method of analysis. Frequency response of
controllers. Frequency response of closed loop systems. Complex control
scheme. Optimum controller settings. Dynamics and control of heat
exchangers, distillation columns and chemical reactors. An introduction to
modern control theory and computer control.
Enhancement of single loop control, digital control systems. Multi loop and
multivariable control. Design of control systems.
ADVANCED SEPARATION PROCESSES:
Solvent extraction; Industrial processes and reagents; Equilibrium; Extraction
kinetics. Extraction processes for metals including copper and uranium.
Laboratory data collection; Column equipment and design principles; Mixer-
settler performance; Coalescence; Adsorption. Ion exchange, principles,
application and equipment. Fundamentals of membrane separation
processes. Operating principles and equipment for dialysis. Reverse osmosis.
Gas separation. Leaching and sorption.
Group 1; Design Engineering

ADVANCED CHEMICAL REACTOR DESIGN:
Design, scale-up and optimization of chemical reactors with allowance for heat
and mass transfer and non-ideal flow patterns. Analysis of rate data for gas-
solid, gas- liquid, and three-phase reaction systems. Transport processes
in heterogeneous catalytic systems. Nonlinear boundary value problems
arising in chemical reactors. Chemical reactor stability and sensitivity.
ADVANCED FLUID MECHANICS:
Solutions of the Navier-strokes equation; Percolation in porous media. Low
Reynolds number flow. Creeping flow around a sphere. Laminar boundary
layer. Free surface flows. Bubble dynamics at low, intermediate and large
Reynolds number. Boundary conditions in the presence of surface active
agents. Inter phase transport in isothermal systems. Fluid dynamics of two
phase flow; Purely viscous non-newtonian constitutive equations. Fluidization.
ADVANCED HEAT TRANSFER:
Optimal design of shell and tube heat exchangers; Pinch technology. Flow
arrangements of increased heat recovery. Condensation of single vapours;
Condensation of single and mixed vapours; Vaporizers, evaporators and
reboilers. Extended surfaces heat transfer. Cooling towers. Furnace design
and operation. Process design of equipment for heat transfer operation based
on performance and economic optima.
86
ADVANCED MASS TRANSFER:
Uses and characteristics of separation processes; Simple equilibrium
processes. Additional factors influencing product purities. Multi-stage
separation processes. Patterns of change and computational approaches.
Limiting flows and stage requirements. Empirical correlation, stage to stage
methods. Successive approximation methods. Capacity and efficiency of
contacting devices; Energy requirements of separation processes. Selection of
separation processes. Optimal design and operation of separation processes.
NUMERICAL METHODS IN CHEMICAL ENGINEERING:
Numerical treatment of ordinary differential equations and partial differential
equations; Sampling theory, Inference and estimation; Tests of Hypotheses,;
THEORY-test, chi-square test, F-Test and analysis of variance. Regression
analysis and correction. Random walk and poison processes, Application of
simulation to the solution of engineering problems. Linear programming.
DESIGN OF HEAT RECOVERY SYSTEMS:
Introduction to heat integration, energy targeting and pinch analysis, heat
exchanger network design for maximum heat recovery, heat exchanger design,
utilities provision, capital and energy trade-offs, automated design of heat
exchanger networks, retrofit of heat exchanger networks, heat engines, heat
pumps, and refrigeration. Heat integration of reactors, separation processes.
Data extraction.
PARTICLE DYNAMICS:
Flow around particles. Drag force, Motion of particles and bubbles;
Sedimentation. Settling. Fluidization. Centrifugation. Filtration. Gas cleaning.
Theory of cyclones. Atomization. Power storage. Solid conveying.
Aerodynamics; Instability of liquids and mechanics of drop formation.
Agglomeration mechanics.
EXPERIMENTAL DESIGN AND ANALYSIS:
Fundamentals of design of experiments; Interactions in processes; A
systematic methodology for design of experiments; Single factor
experiments; Analytical comparisons among treatments and trend analysis;
Two factor experiments; higher- order factorial experiments; Decreasing error
variance; Other designs; Fitting regression models.
PROJECT MANAGEMENT:
Project identification and formulation. Project selection models. Feasibility
preparation including market evaluation, Demand forecasting. Site selection
and survey. Plant capacity decisions. Project engineering including selection
of technology. Industrial proprietary rights. Procurement operations; Contracts
and contractors. Project implementation, PERT/CPM. Resource allocation;
Cost estimates. Progress reporting. Industrial hazards and safety
consideration; Quality Management in Projects. Project Audit; Use of computer
software packages in project management.
87
Group 2; Process Engineering
BIOCHEMICAL ENGINEERING:
Characteristics of industrial micro-organism. Growth of micro-organism. Basic
metabolic processes. Bio-degradation. Bio-mass productivity and activity.
Aerobic and anaerobic processes; Nitrification and De-nitrification processes.
Stirred tank bioreactor. Jet bioreactor. Reciprocating jet bioreactor. Hollow fibre
bioreactor. Fuidized bed bioreactor. Application of various bio processes for
the treatment of industrial wastes and production of chemicals. Theory of Bio-
chemical processes involved in the production of food products, beverages,
organic acids, industrial solvents, various pharmaceutical products and
commercial enzymes.
COMPUTATIONAL FLUID DYNAMICS:
General Differential Equations; Numerical solution of energy and Navier-
Stokes Equations; Numerical schemes and algorithms; Methods of obtaining
convergence; Transient analysis; finite difference and finite element methods
applied to fluid mechanics; Matrix solving Techniques; Recent developments
in CFD; Control Volume Formulation; Finite Volume Method. Development of
computer programs for CFD problems.
COMPUTER AIDED PROCESS DESIGN:
Selection and design of chemical, biochemical or petrochemical processes,
equipment and control systems, case studies. Comparison and optimization;
Equipment evaluation and estimating procedures using computer methods.
Process oriented Languages, data banks, decompositional methods related
to process systems arrangement. Heuristic synthesis of equipment
sequences. Application in chemical and petro-chemical processes.
OCCUPATIONAL HEALTH AND SAFETY IN PROCESS INDUSTRIES:
Introduction to occupational health and safety, basic concepts of health and
safety in process industries. Hazards and types of hazards in chemical and
process industries. Causes of accidents in industries, concept and principles
of accident prevention in industries, risk analysis, safety performance
measurement in industries, strategies for control of occupational safety and
health hazards in process industries.
PROCESS DESIGN AND OPTIMIZATION:
A coordinating course consisting of Chemical Engineering problems of
considerable complexity which require for their solutions the application of
thermodynamics, transport processes, reaction engineering. The selection of
materials of construction. The organization for optimization. Optimization
techniques. Function of a single variable. Analytical and numerical methods.
Multivariable functions, analytical and numerical methods. Function of
continuous variable, analytical and numerical methods. Optimization in
practice.
TRANSPORT PROCESSES:
Development of differential and integral forms of Momentum and Energy
88
conservation equations; The analogy between heat and momentum transfer;
Solution of laminar flow and inviscid flow problem; Boundary layer theory;
Turbulent flow, conductive and convective heat transfer problems; Heat
transfer during laminar and turbulent flow. Solution of steady and transient
heat and mass diffusion problems; Convective heat and mass transfer in
laminar and turbulent flow; Interphase heat and mass transport.
PROCESS MODELING & CONTROL:
Mathematical Modeling; Dynamic Behaviour of Linear Low Order Systems;
Dynamic Behaviour of Linear Higher Order Systems; Inverse Response
Systems; Time-Delay Systems; Frequency-Response Analysis; Stability.
Process Identification: Empirical Process Modeling; Feedback Control
Systems; Conventional Feedback; Controller Design; Controller Design for
Processes with Difficult Dynamics; Model-Based Control; Review of Partial
Differential Equations, Physical behaviours of Partial Differential Equations;
Mathematical Tools, e.g. Tensors, combination of variables; Mathematical
Modeling in MATLAB, SIMULINK.
PROCESS SAFETY AND LOSS PREVENTION:
Introduction to hazard, accident and loss. Legislation and law. Major hazard
control and management systems. Hazard identification and safety audit.
Hazard assessment. Plant layout. Process and pressure system design.
Safety in plant operation. Maintenance and modification. Control system
design. Human factors in control system design. Emission and dispersion.
Fire, explosion and toxic release and storage. Transport. Emergency
planning, Personal safety and safety systems.
Group 3: Energy Engineering

SUSTAINABLE ENERGY ENGINEERING:
Chemical fuels; Characteristics of chemical fuels; Chemical fuels reserves and
production in Pakistan; Combustion chamber design. Clean coal technology.
Fluidized bed combustion. Atmospheric pressure FBC boiler. Atmospheric
pressure FBC furnaces. Fast fluidized bed systems. Pressurized fluidized
bed combustion. Pollutant emissions in combustion processes. Primary and
secondary fuels; Energy conversion with combustion. Wind power. Water
power; Solar power. Geo thermal power. Nuclear power. Calculations in fuel
and energy, energy economics. Energy conservation methodologies of
selected systems, Renewable energy technologies.
ENVIRONMENTAL ENGINEERING:
Introduction to environmental engineering and basic terminology.
Environmental issues at global, regional and national levels. Types of
environmental pollution and their control. Land pollution. Water pollution. Air
pollution and noise pollution. Plastic materials. Recycling. Effects of pollutants
on living systems. Effluent Guidelines and standards; Monitoring of pollution;
Conservation of Material Resources and Energy through recycling. Water
pollution, Waste water and its treatment. Industrial waste treatment and
89
disposal. Air pollution and its abatement. Solid waste management; Noise
pollution and its abatement; Radioactivity and its monitoring. Pollution control
of selected industry. Mathematical modeling of environmental pollution control.
Environmental Management and Auditing system (EMAS). Sustainable
development. Environment friendly technologies and cleaner production.
Pollution prevention. Life cycle analysis.
ENERGY MANAGEMENT & AUDITING:
Definition, Energy audit- need, Types of energy audit, Energy management
(audit) approach-understanding energy costs, Bench marking, Energy
performance, Matching energy use to requirement, Maximizing system
efficiencies, Optimizing the input energy requirements, Fuel and energy
substitution, Energy audit instruments.
POWER PLANT ENGINEERING:
A thermodynamics review, First & Second Law of Thermodynamics, Open and
Closed system, Cycle, Property Relationships, Concept of Reversibility,
Concept of Entropy, Carnot Cycle, Rankine, Ideal Rankine & Externally &
Internally Irreversible Rankine cycle, superheat, Reheat, Regeneration, Open
and closed or Direct-Contact Feed water Heaters, Efficiency and Heat Rate,
The Placement of Feedwater Heaters, Supercritical-Pressure Cycle,
Cogenerations.
Introduction to Fossil-Fuel Steam Generators, Fire and water-Tube Boiler,
Once-through Boiler, Steam-Generator Control, Fuels and Combustion, Coal
Analysis, Coal Firing, Mechanical Stoker, Fluidized-Bed Combustion, Liquid
Fuels, Liquid, Gas, and Solid By-products, Synthetic Fuels, Biomass, Heat of
Combustion, Heating Values, Turbines, Impulse Principle & turbines,
Efficiencies, Turbine Arrangements, Gas Turbines & Combined Cycles, Ideal
& non ideal Bryton Cycles, combined Cycle for Nuclear Power plants
Principles of Nuclear Energy
Atomic Structure, Chemical and Nuclear Equations, Energy from Nuclear
Reactions, Nuclear Fusion and Fission, Energy from Fission and Fuel Burnup,
Radioactivity, Decay Rates and Half-Lives, Neutron Energies, Thermal
Neutrons, Nuclear Cross Sections, Neutron Flux and Reaction Rates, Fission
Reactor Types, Reactor Control, Pressurized-water Reactor (PWR), boiling-
water Reactor (BWE), The Gas-Cooled Reactor (GCR), High-Temperature
Gas-Cooled Reactor (HTGR), Pebble-bed Reactors
Geothermal Energy, Past, Present, and Future, Origin and Types of
Geothermal Energy, Operational and Environmental Problems, Petrothermal
Systems, Hybrid Geothermal-Fossil Systems. Solar Energy, Extraterrestrial &
Terrestrial Solar Radiation, Solar-Electric Conversion System, Receiver,
Thermal-Storage System, World Experience Wind Energy, Principles of Wind
Power, Wind Turbine Operation, Site Characteristics, New Developments:
Small & large Machines Energy from the Oceans, Ocean Temperature
Differences, Open or Claude Cycle, Ocean Waves & Wave Motion, Energy and
Power from Waves, Wave-Energy Conversion by Floats, Tides, Simple Single-
90
Pool Tidal System.
Energy-Storage Systems, Pumped Hydro, Compressed-Air Storage, Energy
Storage by Flywheels, Electrical Battery Storage, Superconducting Magnetic
Energy Storage, Thermal Sensible Energy Storage, Latent Heat Energy
Storage, Chemical-Reaction Storage
Recommended Book:
1. Power plant Technology by M.M. El-Wakil
COAL TECHNOLOGY:
Introduction to combustion & coal Technology, coal preparation, processing,
Utilization & Emission, Clean Coal Technology, Co-combustion, Co-firing
concepts, Coal carbonization, Coal Washing, Coal Blending, Coal Gasification,
Integrated Gasification Combined Cycles (IGCC) ,Early and Commercial
Gasifies, Coal Briquetting, Coal Utilization in power plants and other industries,
CO2 Capturing Technology, Effects of usage of coal on human health and
environment, LCA process.
Group 4: Energetic Materials

POLYMER ENGINEERING:
Structure and properties of polymers. Analysis and testing of polymers.
Methods of polymerization and co-polymerisation. Preparation and properties
of commercially important polymers. Polymers processing, equipment and
machinery. Polymer blends, formulation and performances. Synthesis of
high polymers, properties, thermodynamics and molecular weight. Polymer
additives, blends and composites. Commodity thermoplastics and specializing
polymers. Polymer processing and rheology. Application of polymers. Energetic
polymers for composite propellents. Extrusive and Casting of polymer-based
composition.
PROPELLANTS AND EXPLOSIVES:
Explosion theory and types of explosions; The chemistry of explosive
compounds and mixtures; The concept of fuel and oxidant, oxygen balance;
Thermo-chemistry, simple prediction of heat, temperature and pressure of
explosion; Introduction to deflagration, detonation and classification of
explosives; Commercial and military HE, power, brisance; Aluminized HE;
Introduction to wave shaping and shaped charges; Principles of propellant
chemistry, solid and liquid propellants for guns, rockets and mortars;
Primary explosives, initiation, effect of heat on explosives, explosives trains;
Principles and applications of pyrotechnics; Safety, reliability and testing of
explosives; Management of explosive including classification and storage.
ROCKET PROPULSION TECHNOLOGY:
Background and History of Rocket Propulsion, Classification, Applications,
Thrust, Exhaust Velocity, Energy and Efficiencies, Nozzle Theory and
91
Thermodynamic Relations, Chemical Rocket Propellant Performance
Analysis, Solid Propellant Rocket Fundamentals, Propellant Burning Rate,
Combustion Models, Basic Performance Relations, Propellant Grain and
Grain Configurations, Solid Propellant Classification, Propellant
Characteristics, Hazards, Propellant Ingredients, Propellant Processing and
Manufacture, Propellant Grain Mechanical Properties, Solid Rocket
Components and Motor Design, Introduction to Liquid Propellant Rocket
Engines, Liquid Propellants.
COMBUSTION OF ENERGETIC MATERIALS:
Thermochemistry of Combustion, Energetics of Propellants and Explosives,
Combustion of Crystalline and Polymeric Materials, Combustion of Double
Base Propellants, Combustion of Composite Propellants, Combustion of
Explosives, Combustion in a Rocket Motor. Combustion Rate Predictions and
Measurement Methods.
CIVILIAN APPLICATIONS OF ENERGETIC MATERIALS:
Rock blasting, Mining, Motor car safety bags, Oil exploration, Outer space
exploration, Fireworks, Explosive welding, Controlled demolition industry,
Agriculture sector, Medical industry, Civil Engineering and Nuclear devices.
Group 5: Advanced Materials

ADVANCED COMPOSITE MATERIALS:
Introduce to advanced materials for engineers, emphasizing the production
/structure /property /function relation and application of a number of advanced
materials mainly for Biomedical and Aerospace applications. Background to
thermosetting and thermoplastic polymer matrix composites; Overview of
established manufacturing processes; Developing processes; Automation;
Machining; Future process developments (including tufting, nanoparticle
modified resins, hybridised materials, Applications - case studies from
aerospace, automotive, marine and energy sectors; Refractory materials and
coatings for high temperature applications, thin film shape memory alloys for
MEMS.
NANO TECHNOLOGY:
Basic Concepts, History of Nano, Size Effects on Properties, Top Down vs
Bottom Up, Nano Tools, Nanoparticle synthesis & characterization, Other
Nanomaterials, Sensors, Biomaterials, Energy, Nanomaterials in the
Environment.
MATERIALS ENGINEERING:
Introduction to materials: Atomic structure, crystal structure, imperfections,
diffusion, mechanical properties, dislocations and strengthening mechanisms,
phase diagrams, phase transformations, solidification, corrosion. Basic and
alloy steels, tensile behaviour of metals, work and precipitation hardening,
recovery and recrystallization.
92
Structural steels C-Mn ferrite-pearlite structural steels, specifications and
influence of composition, heat treatment and microstructure on mechanical
properties. Fracture, weldability and the influence of welding on mechanical
properties. Corrosion Resistant Materials - Stainless steels - austenitic, ferritic,
martensitic and duplex stainless steels compositions, microstructures,
properties. Welding and joining processes, weld metal, heat affected zones and
weld cracking. Non-metallic Materials - Polymers and composites
manufacturing issues, physical properties and mechanical behavior Structure
and properties and applications of ceramics. Principles underlying electrical and
magnetic properties of materials.
MECHANICAL BEHAVIOUR OF MATERIALS:
Overview of failure behaviour of cracked bodies; crack size influence, brittle and
ductile behaviour; influence of material properties; cyclic loading and chemical
environment. Linear elastic fracture mechanics (LEFM) and crack tip stress
fields, stress concentration, stress intensity, plane stress and plane strain;
fracture toughness in metallic materials; fracture toughness testing; calculations
of critical defect sizes and failure stress. elastic- plastic failure criteria; Fracture
of rigid polymers and standard tests for fracture resistance of polymers.
Delamination fatigue tests. Emerging CEN/ISO standards, current ESIS test
procedures. Crack extension under cyclic loading; regimes of fatigue crack
growth; influence of material properties and crack tip plastic zones; calculation
of crack growth life and defect assessment in fatigue; crack closure and variable
amplitude loading; short cracks and the limits of LEFM; software design tools
for fatigue crack growth. Static loading-stress corrosion cracking; corrosion
fatigue.
93
RECOMMENDATIONS
1. All Chemical Engineering institutions should review their educational

process and make it more sustainable.
2. The courses should be taught in a way to develop a more application

based and research oriented approach.
3. The student assessment should be based on questions related with

knowledge and understanding of subject including engineering analysis,
investigation, engineering practices and transferable skills.
4. Latest software relating to chemical engineering subjects such as

HYSYS, MATLAB, ANSYS, Auto CAD, Math, CAD, Pro-E should be made
available at Institutions offering programmes in Chemical Engineering.
5. Faculty training in core disciplines should be arranged at Institutions

offering programmes in Chemical Engineering.
6. Laboratory facilities should be strengthened to facilitate the lab work

associated with theory courses.
7. All laboratories should be supervised and managed by qualified Lab

Engineers.
8. Efforts should be made to strengthen academia-industry interaction.
9. Masters in Chemical Engineering by research is strongly recommended to

be incorporated in the postgraduate programme.
10. The Practical/Lab work should comprise at least 20-30% of the total credit
hours.
11. All the Universities/Institutions should make arrangements for practical

training of their students in industrial organizations during summer.
12. To strengthen research capacity of HEIs, the honorarium for the

postgraduate students, in engineering disciplines, is recommended to be
equivalent to BPS- 17 salary.
94

Chemical Engineering Draft

Uploaded by

Copyright:

Available Formats

Chemical Engineering Draft

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chemical Engineering Draft

Uploaded by

Copyright:

Available Formats

CURRICULUM

HIGHER EDUCATION COMMISSION

Mr. Fida Hussain Director General (Acad)

Ms. Ghayyur Fatima Director (Curri)

Mr. Rizwan Shoukat Deputy Director (Curri)

Mr. Abid Wahab Assistant Director (Curri)

Mr. Riaz-ul-Haque Assistant Director (Curri)

Composed by: Mr. Zulfiqar Ali, HEC, Islamabad

6. Scheme of Studies for BE, BSc in Chemical 15

7. Detail of Courses for BE, BSc in

8. Social Sciences and Management Courses 67

10. Detail of Courses for ME, MSc 84

University Grants Commission (UGC) was designated as the competent

In compliance with the above provisions, the Curriculum Division of HEC

In order to impart quality education which is at par with international standards,

It is hoped that this curriculum document, prepared by the respective NCRCs,

STAGE-I STAGE-II STAGE-III STAGE-IV

CURRI. UNDER CURRI. IN DRAFT FINAL STAGE FOLLOW UP

COLLECTION OF APPRAISAL OF 1ST PREP. OF FINAL QUESTIONNAIRE

CONS. OF CRC. FINALIZATION OF INCORPORATION OF COMMENTS

PREP. OF DRAFT APPROVAL OF PRINTING OF REVIEW

Abbreviations Used: IMPLE.OF CURRI. BACK TO STAGE-I

The final meeting of National Curriculum Revision Committee (NCRC) in the

Sr. Name & Address Status

The chemical engineering curriculum is so designed that it not only includes

Courses in chemical engineering fundamentals (material and energy

Mission of chemical engineering undergraduate program is to provide

Understanding of the needs of the society and demands of the

Humanities Presentation skills

Chemistry Physical & 3 1 4

Fuels & Energy 3 1 4

Grand Total 50 136

Chemical Engineering Design Engineering Oil & Gas

** New area/subjects can also be included according to the

Mass Transfer 2 1 3 Instrumentation & 3 1 4

Probability and 2 0 2 Technical Report 2 0 2

Separation Processes- Entrepreneurship

Design Project- I 0 3 3 Design Project-II 0 3 3

Objectives of the course:

Objectives of the course:

STUDY OF SELECTED TEXT OF HOLY QURAN

STUDY OF SELECTED TEXT OF HOLY QURAN

SEERAT OF HOLY PROPHET (S.A.W) II

SELECTED STUDY FROM TEXT OF HADITH INTRODUCTION TO

ISLAMIC LAW & JURISPRUDENCE

ISLAMIC CULTURE & CIVILIZATION

ISLAM & SCIENCE

ISLAMIC ECONOMIC SYSTEM

POLITICAL SYSTEM OF ISLAM

SOCIAL SYSTEM OF ISLAM

CHEMICAL PROCESS PRINCIPLES I

2. Felder Richard M., Rousseau Ronald W. Elementary Principles of

INORGANIC & ORGANIC CHEMISTRY

CALCULUS & ANALYTICAL GEOMETRY

Pakistan Studies (Compulsory)

English II (Communication Skills)

Note: documentaries to be shown for discussion and review

CHEMICAL PROCESS TECHNOLOGY

2. Felder Richard M., Rousseau Ronald W. Elementary Principles of