MMUP Sample Questions

1. What do we call Synchronous motor working on a lead power factor at no load?

a. Synchronous condenser
b. Reluctance motor
2. A synchronous motor on No-load can be used as:
a. synchronous condenser
b. induction motor
c. induction generator
3. Synchronizing motor leading power factor
a. Synchronic condenser
b. Universal motor
c. Relocating motor
4. Which type of motor used in home ceiling fan:
a. capacitor motor
b. shaded pole motor
c. universal motor
5. Which type of motor used in ceiling fan?
a. Capacitor start type
b. Permanent capacitor run
c. Capacitor induction run.
6. Starting method of IP Motors used in House holding Fans?
a. Capacitor Start
b. Induction start
c. Split phase
d. none of the above
7. Best starting for single phase motor.
a. Connect resistor
b. Connect inductor
c. Connect resistor and inductor in series
d. Connect capacitor.
8. What is the best economical way to start a single phase motor
a. Resistive method
b. Inductive method
c. Capacitive method
d. None of the above
9. Which of the following Braking system is used in the induction Motor?
a. Regenerative Barking
b. Plugging Braking
c. Dynamic Braking
 d. All of the above.
10. What one of the below devices is faster and consumes less power in large scale projects?
a. DSP
b. Microcontrollers
c. ASIC
d. FPGA
11. For Fire alarm & smoke detector it is preferable to use
a. Microcontrollers
b. ASIC
c. FPGA
12. Incandescent Lamp flickering due to
a. Voltage
b. Frequency
13. Cascade amplifier is used because
a. High Voltage gain
b. High output impedance
c. High input impedance
14. Cascade amplifier used to reduce load effect, the input impedance will be
a. High
b. Low
c. Medium
15. What is the low-pass filter?
a. It will let pass low frequencies? (or it blocks high frequency)
b. It will let pass high frequencies?
c. It will let pass a band of frequencies?
d. It will eliminate a band of frequencies?
16. What is the role of the zener diode?
a. Rectification
b. Amplification
c. voltage regulation
17. Ohms Law (the right one is U=RI, they put choices not related to this law)
18. A synchronous motor at over excited can be used as:
a. Leading power factor
b. Motor unity
c. Motor lagging
19. Voltage regulator negative for synchronous motor
a. Leading power factor
20. What is the QSAS?
a. Qatar Sustainability Assisting Systems
21. For an inverter op-amp, what will be the equivalent output resistance?
a. Zero
b. Infinity
 c. Relative forward resistance
d. Same as the input resistance.
22. The heat loss inside a straight conductor is 60J upon applying current I for 5s. if the resistance of
the conductor is decease to half, and the same current is applied for 5s, what will be the heat
dissipation:
a. 60J
b. 30J
c. 15J
d. 120J
23. Breaking for induction motor
a. Regeneration
b. Dynamic
c. Plugging
d. All above
24. Fan out logic gate is
a. Number of gate
b. Number of gate connect to output
25. Type of amplifier at transmitter?
a. Power amplifier
b. Differential Amplifier
26. Loading effect can be reduced in a system by using
a. Integrator
b. Inverted Amplifier
c. Non - Inverted Amplifier
d. Diff Amplifier
27. Transformer humming due to
a. Vibration in Lamination
b. vibration in oil
28. If fuse rate = 8 Ampere, what does mean?
29. First line in transmission
a. Ground
b. R-phase
c. B-phase
d. Neutral
30. Circuit breaker is
a. Current interrupting device
b. Power factor detection device
31. Incandescent lamp operating at a power factor of
a. Leading
b. Lagging
c. Unity
d. Zero
32. Terminal represents control input of BJT
a. Emitter
b. Base
c. Collector
33. Changing in the excitation in grid having an alternator connected to it will having the following
effect
a. Change in active component
b. Change in reactive component
c. No change
34. If a sudden excitation happens to the alternator what will be its effect:
a. Variation in real power on load side.
b. Variation in apparent power on load side.
c. Power factor effects.
d. The frequency of the generated wave form will be affected.
35. Transducers convert physical quantity into
a. Electrical
36. Sensor transducers will transfer.
a. Move to electrical signals
b. Heat to mechanical signal.
37. How much is the slip for synchronous generators
a. Zero
b. Negative
c. positive
38. Difference between inch and centimeter
a. 2.45
b. 2.54
39. Common breakers used in distribution level
a. Air circuit breaker ACB
b. Oil type
c. Vacuum VCB
40. Question regarding what does an engineer do!
41. Difference between MOSFET and BJT
a. MOSFET amplifies current
b. BJT is bigger in size and dimensions
42. What is the DC gain of the transistor NPN?
a. The right answer is IC/IB, they put also the formulas of the MOSFET which are wrong for
this question
43. How the diode let pass the current?
a. Only in one way, it will block the other way
44. Power transformers are generally designed to have maximum efficiency around:
a. No load
b. half load
 c. near full load
d. over load
45. Minimum cross sectional area of earth continuity conductor in buildings used:
a. 20 AWG
b. 16 AWG = 1.5 mm2
c. 12 AWG
d. 10 AWG
46. For power factor correction of power systems which one is used:
a. capacitor
b. inductor
c. resistors
47. Terminals of a transistor (BJT):
a. Base, collector & emitter
b. gate, collector & emitter
c. gate, emitter & drain
48. Differential Amplifier with High CMRRS means:
a. High rejection of noise
b. Amplify noise
c. High amplification gain
49. High voltage winding of transformer has ---------- resistivity than the low voltage side.
a. Lower
b. Higher
c. Equal
d. Lower or Equal
50. ABET stands for Accreditation Board for Engineering and Technology?
a. True
b. False
51. What does the power factor stands for:
a. Cosine of the angle between voltage and current.
b. Sine of the angle between voltage and current.
c. Apparent power over real power.
52. Displacement factor
a. Cosine angle between voltage and current
b. sine angle between voltage and current
c. tan angle between voltage and current
d. cotangent angle between voltage and current
53. If the induction motor speed at no-load is 745 RPM, what is the speed of the motor:
a. 700 RPM
b. 750 RPM
c. 800 RPM
d. 850 RPM
54. What are the types of losses
 a. Armature losses
b. Winding losses
55. Op-amp (operational amplifier) input resistance:
a. Zero
b. Infinity
c. Relative resistance
d. Same output resistance.
56. Which of the following devices has a metalsemiconductor junction formed between a metal
and a semiconductor:
a. schottky diode
b. zener diode
c. varactor diode
d. tunnel diode
57. Inverter allowed noise level question given the values of VOH, VOL, VIH, VIL. And need to get
NMH and NML
58. Which of the transmission voltage is not applied in Qatar Electrical Specs:
a. 66KV
b. 132KV
c. 220KV
d. 400KV
59. CMOS inverter is superior to the R-pull up inverter due to:
a. High impedance
b. Smaller propagation delay
c. Symmetric transfer characteristics
60. Ultrasound test used to determine
a. Cracks
b. Position of cracks
c. Length of cracks
d. All of above
61. A passive filter can
a. filter only
b. filter & amplify only
c. amplify only
d. none of the above
62. Wireless receiver?
a. power amplifier
b. differential amplifier
63. In receiver and transmitter. Which kind of amplifier used.
a. Power amplifier
64. Major factor that has to be considered when designing a distribution system is
a. Efficiency
b. Voltage Regulation
 c. PF
d. Reliability
65. To get rid of DC offset use?
a. Low pass filter
b. high pass filter
c. Band pass filter
d. Stop band pass filter
66. For forward biasing
a. Anode 3v cathode 7v
b. Anode 5v cathode 3v
c. Anode 7v cathode 10v
67. Transformer resistivity
a. High voltage higher than low voltage
b. High voltage lower than low voltage
c. High voltage equal to low voltage
68. Amplifier working with good gain in?
a. Reverse region
b. Cutoff region
c. Active region
d. Saturated region
69. What is wrong sentence
a. Donor N Type
70. What is MOSFET
a. Transistor
b. Thyristors
c. Amplifier
71. What is the efficiency of BJT = IC/IB
72. What is the power consumption of BJT
a. 15%
73. Alternator connected on no load condition, what affect the efficiency.
a. Speed
b. Voltage
c. Armature losses
74. Transformer saturation
a. High efficiency, low no load losses.
b. Low efficiency, low no load losses.
c. Low efficiency, high no load losses.
d. High efficiency, high no load losses.
75. To minimized loading effect use?
a. Resistance
b. Capacitors.
c. Inductors.
76. Best type of switchgear
a. SF6
b. VCB
c. OCB
d. ACB
77. What is least influential in projects?
a. Time
b. Materials
c. Manpower.
78. Which one of the following has High input Impedance?
a. NPN-BJT.
b. PNP-BJT.
c. MOSFET.
d. Both BJT & MOSFET.
79. Ripple Factor of Zener Diode Depends on:
a. Zener Voltage
b. I/P Impedance
c. O/P Impedance
d. None of the above
80. I/P side of the GSM Network should contain?
a. Low Pass Filter
b. High Pas Filter
c. Band Pass Filter
d. None of the above.
81. Power Consumption in the advanced embedded system is
a. 10%
b. 50%
c. 80%
d. None of the above.
82. Power Consumption in Advanced Embedded can be reduced by using
a. Pipe Lining.
b. Voltage sensing
c. Parallelizing
d. None of the above
83. A 4pole Alternator runs in 750 rpm, what is the frequency?
a. 50 HZ
b. 25Hz
c. 60Hz
d. None of the above
84. Earth Electrode shall be placed in an earth pit?
a. Vertical
b. Horizontal
 c. Any Angle
85. Which of the following is a weak power system?
a. Power system with high short circuit capacity and high sensitivity to harmonics
b. Power system with high short circuit capacity and low sensitivity to harmonics
c. Power system with low short circuit capacity and high sensitivity to harmonics
d. Power system with low short circuit capacity and low sensitivity to harmonics
86. Once the transformer is saturated its no load current will be
a. Increases
b. Decreases
c. no change
d. Cancelled
87. Lower current frequency of an NPN transistor depends on
a. Input Imp
b. OP/P imp
c. System Voltage
d. All of the above
88. Harmonics in a system is mainly due to:-
a. Variable Imp Load
b. Saturated magnetic load
c. Power Electronics Load
d. All of the above
89. When I current is passing through R resistance for a time period of t seconds, then the electrical
energy generated will be:
a. I2Rt
b. IR2t
c. 2IRt
d. IR2/t
90. Digital codes only two input
a. True
b. False
91. Ohms Law (the right one is U=RI, they put choices not related to this law)
92. The best mix around an earth electrode (Lime sand mixture? Coal & Salt? Etc the right choice is
sand mixture with copper mulch)
93. In case of Transformer saturation how the efficiency and the no load current will behave?
(efficiency decrease and current output is similar to the magnetic field in the transformer and
chopped with notches)
94. What is the circuit breaker application? Its basic function is to detect a fault condition and
interrupt current flow.
95. Synchronous speed for motor 8000 RPM , 50Hz, calculate number of poles.
96. Synchronous speed for motor 8000 RPM , rotor speed 7500 RPM calculate slip.
 MMUP EXAM
1. Cascaded amplifier used to reduce load effect, the input impedance will be
a. High
b. Low
c. Medium
2. Cascaded amplifier used to reduce load effect, the output impedance will be
a. High
b. Low
c. Medium
3. Which one of the following is not correct based on Ohms Law:
a. Potential / current = constant
b. Current / potential = constant
c. Current = potential x resistance
d. Potential = current x resistance
4. The heat loss inside a straight conductor is 60J upon applying current I for 5s. if the resistance of
the conductor is decease to half, and the same current is applied for 5s, what will be the heat
dissipation:
a. 60J
b. 30J
c. 15J
d. 120J
5. If fuse rate = 8 Ampere, what does mean?
a. Cant pass current below 8 A
b. Melts if currents exceeded 8 A
6. Circuit breaker is
a. Current interrupting device
b. Power factor correction device
7. BJT acts as a switch in:
a. Linear Region
b. Saturation Region
c. Active Region
8. Changing in the excitation in grid having an alternator connected to it will having the following
effect
a. Change in active component
b. Change in reactive component
c. No change
d. The frequency of the generated wave form will be affected.
9. Differential Amplifier with High CMRRS means:
a. High rejection of noise
b. Amplify noise
c. High amplification gain
10. Which of the following devices has a metalsemiconductor junction formed between a metal
and a semiconductor:
a. schottky diode
b. zener diode
c. varactor diode
d. tunnel diode
11. Which of the transmission voltage is not applied in Qatar Electrical Specs:
a. 66KV
b. 132KV
c. 220KV
d. 400KV
12. Which statement is not correct: (related to semiconductors doping)
a.
13. Power Consumption in the advanced embedded system is
a. 10%
b. 50%
c. 80%
d. None of the above.
14. Earth Electrode shall be placed in an earth pit?
a. Vertical
b. Horizontal
c. Any Angle
15. Which of the following is a weak power system?
a. Power system with high short circuit capacity and high sensitivity to harmonics
b. Power system with high short circuit capacity and low sensitivity to harmonics
c. Power system with low short circuit capacity and high sensitivity to harmonics
d. Power system with low short circuit capacity and low sensitivity to harmonics
16. Harmonics in a system is mainly due to:-
a. Variable Imp Load
b. Saturated magnetic load
c. Power Electronics Load
d. All of the above
17. What is HRC fuse:
a. High resistance and capacitance
b. High rupturing capacity
18. Number 34 in the following N34, E usually will be specified with:
a. Starting point
b. Traverse
c. Bearing
19. What is spinning reserve:
20. Project Control will be:
a. Before construction
b. During construction
c. After construction
d. Throughout the process
21. What is a system:
a. Group of elements having one input and one output
b. Group of elements making a function
22. The forward pass review of the project management will indicate the following:
a. The earliest start of the task
b. The earliest finish of the task
c. Critical path (longest path)
d. Only A & B
e. A,B & C are all correct
23. What is the least level of WBS
a. Deliverable
b. Cost
c. Work package

MMUP Sample Questions

1. If you were awarded a project, you will start work:

a. One week before the approval of the authorities
b. After the approval of the authorities
c. One day before the approval of the authorities
2. Project Scope Management:
a. Define scope and control scope
b. Executing scope and verify scope
c. Closing process and Create work breakdown structure
d. All of the above
e. Only A & B
3. Scope Management starts with is:
a. To identify the client requirements
b. Meet the team
c. Review strategic plan
4. Final as built drawings for what purpose
a. To keep record for later maintenance
b. To give more work to architect
c. To be used for further renovation
5. Control department work starts
 a. From the beginning of the project
b. During construction
c. After construction
6. Project management is ideally suited except
a. Accountability
b. Flexibility
c. Innovation
d. Speed
e. Repeatability
7. A critical path is the ----------------------in the project management:
a. longest
b. shortest
c. none
8. The forward pass review of the project management will indicate the following:
a. The earliest start of the task
b. The earliest finish of the task
c. Critical path (longest path)
d. Only A & B
e. All of the above
9. The back pass review of the project will indicate the following:
a. The latest start of the task.
b. The earliest finish of the task.
c. The critical path.
d. Only A & C
e. All of the above.
10. Intersecting point for WBS and OBS
a. Cost account
b. Intersect matrix
c. Project matrix
d. None of above
11. For operation and designed auto mobile factory
a. Mechanical Engineer
b. Civil Engineer
c. Chemical Engineer
d. Petroleum Engineer
12. Which of the following discipline is most suitable for doing a natural gas pipeline work?
a. Mechanical Engg
b. Petroleum Engg
c. Chemical Engg
d. Civil Engg
13. Gypsum board at residence and industrial building used except
a. Low cost
 b. Ease of installation
c. Recyclability
14. Stress defined
a. Strain time force
b. Mass divide volume
c. Pressure time length
d. None of above
15. What is the last of estimation for project
a. Estimation
b. Assembly schedule
16. Which one of the following is suitable in engineering manner? Decision shall be based on
reason than situation .
a. Quantity Thinking.
b. Logical Thinking.
c. Interpersonal Skills.
d. Honesty.
17. What is QSAS?
a. Qatar Sustainability Assessment System
18. An activity in a project network can be represented by which of the following?
a. Arrow
b. Line
c. Node
d. All of the above
19. Before starting work at site, the major factor has to be checked is?
a. Access to site (EFE)
b. Storage of Water, tools & equipments
c. Safety
d. Approval from MMUP / Civil / Defence etc.
e. All of the above
20. Software programming flow
a. Plan, Do, Check, Act
b. Plan, Do, Act, Check
c. Plan, Act, Do, Check
21. First step of Scope planning starts with
a. Budgeting
b. Current earning estimation
c. Objectives and requirements to satisfy customer
22. In network which point getting more inward flow
a. Float
b. Critical path
c. Slack
d. Merging point
 23. What is the least level of WBS
a. Deliverable
b. Cost
c. Work package
d. Lowest sub deliverable
24. The best place to build an exhibition and convention center (near the Airport? Or in satellite
place far from Urban? Etc)
25. One situation for cancel project.
26. What is the most sensitive period in the project?

MMUP Sample Questions

97. What is the sum of the interior angles of the hexagonal

a. 180
b. 360
c. 720
d. 940
98. Which type of motor used in home ceiling fan
a. Induction start
b. Capacitor start type
c. Permanent capacitor run
d. Permanent induction runs
99. What is the minimum standard approved grounding wire size
a. 20 AWG
b. 16 AWG
c. 10AWG
d. 8 AWG
100. If the induction motor runs 1200 RPM at 100 HZ, what will be the number of the poles:
a. 5
b. 8
c. 10
d. 12
101. Which one of the following is suitable for engineering work Decision shall be based on
reason than situation .
a. Quantity Thinking.
b. Logical Thinking.
c. Interpersonal Skills.
d. Honesty

102. Terminal represents control input of BJT

 a. Emitter
b. Base
c. Collector
d. drain
103. NMOS in the R-pull up mode (W/L) will be used for
a. To force Vo to be at VOL
b.
c.
d.

104. The load resistance for the Cascade amplifier is (it should be the i/p impedance)
a. The resistance after first stage
b. The resistance before first stage
c. The resistance after second stage
d. The resistance before second stage

105. Which is better

a. To have self target and to achieve it
b. To have a goal and try to try to achieve and to maximize the goal.

106. What is the change order (1)change in scope (2)change in time (3)change in cost and budget
a. 1&3
b. 2&3
c. 1&2
d. Any change in the work

107. Main cause of the Transformer humming is

a. Oil and coil vibration
b. Vibration of the core
c. Vibration of the laminators
d. Non of the above.

108. What is the main reason for harmonic in the electrical circuits
a. Impedance
b. Inductance loads
c. Capacitance loads
d. Power electronics loads
109. The dominant power in the embedded circuits is called
a. Dynamic power
b. Static power
c. Leakage power
d. All of the above

110. Which one of the following is suitable for engineering work Decision shall be based on reason
than situation
a. Quantity Thinking.
b. Logical Thinking.
c. Interpersonal Skills.
d. Honesty

111. What is the Micro strip antenna

a. Antenna which is used in electronic circuits
b. Antenna which is used in embedded circuits
c. It is small antenna
d. It is large antenna

112. Number 34 in the following N34 E usually will be specified with

a. Temporary
b. Starting point
c. Traverse
d. Bearing

113. Which of the following is used for rectification circuits

a. Diode
b. Ziner diode
c. PJT transistor
d. FET transistor

114. Breaking for induction motor

a. Regeneration
b. Dynamic
c. Plugging
d. All above
115. Incandescent Lamp flickering can be noticed in case of
a. Voltage increasing
b. Voltage decreasing
c. Frequency increasing
d. Frequency decreasing

116. The Incandescent Lamp will work normally with best efficiency if the power factor is
a. unity
b. 0.5 leading
c. 0.5 lagging
d. Any power factor

117. The compound which will be used around the earth rod is
a. SE salt and sand
b. E Carbon dust with sand
c. Metal with sand
d. Coral salt with sand

118. Wire placed on the top of a transmission line?

a. Ground wire
b. Neutral wire
c. Phase wire

119. The theoretical output resistance for the electrical amplifier

a. zero
b. Infinity
c. Depending on the circuit impedance
d. Non of the above.

120. Ultrasound test used to determine

1. Cracks
2. Position of cracks
3. Length of cracks
4. All of above

121. Main objective to design power system

a. reliability
b. power factor
 c. voltage regulation
d. efficiency

MMUP Sample Questions

122. What is the sum of the interior angles of the hexagonal

a. 180
b. 360
c. 720
d. 940
123. Which type of motor used in home ceiling fan
a. Induction start
b. Capacitor start type
c. Permanent capacitor run
d. Permanent induction runs
124. What is the minimum standard approved grounding wire size
a. 20 AWG
b. 16 AWG
c. 10AWG
d. 8 AWG
125. If the induction motor runs 1200 RPM at 100 HZ, what will be the number of the poles:
a. 5
b. 8
c. 10
d. 12
126. Which one of the following is suitable for engineering work Decision shall be based on
reason than situation .
a. Quantity Thinking.
b. Logical Thinking.
c. Interpersonal Skills.
d. Honesty

127. Terminal represents control input of BJT

a. Emitter
b. Base
c. Collector
d. drain
128. NMOS in the R-pull up mode (W/L) will be used for
a.
 b.
c.
d.

129. The load resistance for the Cascade amplifier is

e. The resistance after first stage
f. The resistance before first stage
g. The resistance after second stage
h. The resistance before second stage

130. Which is better

a. To have self target and to achieve it
b. To have a goal and try to try to achieve and to maximize the goal.

131. What is the change order (1)change in scope (2)change in time (3)change in cost and budget
e. 1&3
f. 2&3
g. 1&2
h. Any change in the work

132. Main cause of the Transformer humming is

e. Oil and coil vibration
f. Vibration of the core
g. Vibration of the laminators
h. Non of the above.

133. What is the main reason for harmonic in the electrical circuits
e. Impedance
f. Inductance loads
g. Capacitance loads
h. Power electronics loads

134. The dominant power in the embedded circuits is called

e. Dynamic power
f. Static power
g. Leakage power
h. All of the above
135. Which one of the following is suitable for engineering work Decision shall be based on reason
than situation
e. Quantity Thinking.
f. Logical Thinking.
g. Interpersonal Skills.
h. Honesty

136. What is the Micro strip antenna

e. Antenna which is used in electronic circuits
f. Antenna which is used in embedded circuits
g. It is small antenna
h. It is large antenna

137. Number 34 in the following N34 E usually will be specified with

a. Temporary
b. Starting point
c. Traverse
d. Bearing

138. Which of the following is used for rectification circuits

e. Diode
f. Ziner diode
g. PJT transistor
h. FET transistor

139. Breaking for induction motor

e. Regeneration
f. Dynamic
g. Plugging
h. All above

140. Incandescent Lamp flickering can be noticed in case of

e. Voltage increasing
f. Voltage decreasing
g. Frequency increasing
h. Frequency decreasing
141. The Incandescent Lamp will work normally with best efficiency if the power factor is
e. unity
f. 0.5 leading
g. 0.5 lagging
h. Any power factor

142. The compound which will be used around the earth rod is
e. SE salt and sand
f. E Carbon dust with sand
g. Metal with sand
h. Coral salt with sand

143. Wire placed on the top of a transmission line?

d. Ground wire
e. Neutral wire
f. Phase wire

144. The theoretical output resistance for the electrical amplifier

e. zero
f. Infinity
g. Depending on the circuit impedance
h. Non of the above.

145. Ultrasound test used to determine

5. Cracks
6. Position of cracks
7. Length of cracks
8. All of above

146. Main objective to design power system

e. reliability
f. power factor
g. voltage regulation
h. efficiency
1- What is the low-pass filter?
a- it will let pass low frequencies? (or it blocks high frequency)
b- It will let pass high frequencies?
c- It will let pass a band of frequencies?
d- It will eliminate a band of frequencies?

2- What is the DC gain of the transistor NPN?

The right answer is IC/IB, they put also the formulas of the Mosfet which are wrong for
this question

3- What is the role of the zener diode?

a- Rectification
b- Amplification
c- voltage regulation

4- How the diode let pass the current?

Only in one way, it will block the other way

A small problem where u have to determine the number of poles of a synchronous

motor, if you know the pulsation ws (rad/sec) & speed Ns (RPM)and the frequency f (Hz)

&

5- In case of Transformer saturation how the efficiency and the no load current will
behave? (efficiency decrease and current output is similar to the magnetic field in the
transformer and chopped with notches)

6- Ohms Law (the right one is U=RI, they put choices not related to this law)

7- The best mix around an earth electrode (Lime sand mixture? Coal & Salt? Etc the right
choice is sand mixture with copper mulch)

8- The best place to build an exhibition and convention center (near the Airport? Or in
satellite place far from Urban? Etc)

9- What is the circuit breaker application? Its basic function is to detect a fault condition and
interrupt current flow.
10- Power transformers are generally designed to have maximum efficiency around:
a- No load
b- half load
c- near full load
d- over load

11- Which breakers used as the main circuit breakers of power distributions in buildings:
a- ACB
b- VCBs
c- oil circuit breakers

12- Which type of motor used in home ceiling fan:

a- capacitor motor
b- shaded pole motor
c- universal motor

13- A synchronous motor on No-load can be used as:

a- synchronous condenser
b- induction motor
c- induction generator

14- Running along the top of transmission line is:

a- ground conductor
b- line conductor

15- Minimum cross sectional area of earth continuity conductor in buildings used:
a- 20 AWG
b- 16 AWG = 1.5 mm2
c- 12 AWG
d- 10 AWG

16- A critical path is the ----------------------in the project management:

a- longest
b- shortest
c- none

17- For power factor correction of power systems which one is used:
a- capacitor
b- inductor
c- resistors
18- terminals of a transistor (BJT):
a- Base, collector & emitter
b- gate, collector& emitter
c- gate,emitter&drain

19- Differential Amplifier with High CMRRS means:

a- High rejection of noise
b- Amplify noise
c- High amplification gain

20- High voltage winding of transformer has ---------- resistivity than the low voltage side.
a- Lower
b- Higher
c- Equal
d- Lower or Equal

21- CMOS inverter is superior to the R-pull up inverter due to:

a- Smaller propagation Delay

22- Which type of motor used in ceiling fan?

a- Capacitor start type
b- Permanent capacitor run
c- Capacitor induction run.

23- ABET stands for Accreditation Board for Engineering and Technology?
a- True
b- False

24- What does the power factor stands for:

a- Cosine of the angle between voltage and current.
b- Sine of the angle between voltage and current.
c- Apparent power over real power.

25- If the induction motor speed at no-load is 745 RPM, what is the speed of the motor:
a- 700 RPM
b- 750 RPM
c- 800 RPM
d- 850 RPM

26- What are the type of losses inside the alternator:

a- Armature losses
 b- Winding losses

27- If a sudden excitation happens to the alternator what will be its effect:
a- Variation in real power on load side.
b- Variation in apparent power on load side.
c- Power factor effects.
d- The frequency of the generated wave form will be affected.

28- Op-amp (operational amplifier) input resistance:

a- Zero
b- Infinity
c- Relative resistance
d- Same output resistance.

29- For an inverter op-amp, what will be the equivalent output resistance?
a- Zero
b- Infinity
c- Relative forward resistance
d- Same as the input resistance.

30- Which of the following devices has ametalsemiconductor junction formed between a metal
and a semiconductor:
a- schottky diode
b- zener diode
c- varactor diode
d- tunnel diode

31- The heat loss inside a straight conductor is 60J upon applying current I for 5s. if the
resistance of the conductor is decease to half, and the same current is applied for 5s,
what will be the heat dissipation:
a- 60J
b- 30J
c- 15J
d- 120J

32- Project Scope Management:

a- Define scope and control scope
b- Executing scope and verify scope
c- Closing process and Create work breakdown structure
d- All of the above
e- Only A & B

33- The forward pass review of the project management will indicate the following:
 a- The earliest start of the task
b- The earliest finish of the task
c- Critical path (longest path)
d- Only A & B
e- All of the above

34- The back pass review of the project will indicate the following:
a- The latest start of the task.
b- The earliest finish of the task.
c- The critical path.
d- Only A & C
e- All of the above.

35- Invertor allowed noise level question given the values of VOH, VOL, VIH, VIL. And need
to get NMH and NML

36- Which of the transmission voltage is not applied in Qatar Electrical Specs:
a- 66KV
b- 132KV
c- 220KV
d- 400KV

Additional new questions :

1. Flickering in Flurecent is due to
a. Increase in frequency
b. Decrease in f
c. Inceras in voltage
d. Decrease in voltage
2. UPS is and equipment :
a. Connected in parallel to work in normal condition
b. Connected in series to work in normal condition
c. Connected in parallel to work in disturbance
d. Connected in series to work in disturbance
3. Voltage regulation of an alternator may be ________ if connected to capacitive load
a. Negative
b. Positive
c. Zero
d. Non
4. ASCR oof conductor have 7 steel wires and 25 aluminum wires can be specified as:
a. 7/25
b. 7/32
 c. 25/32
d.
5. The motor used in travelling cranes is :
a. Ward Leonel controlled DC shunt motor
b. AC split motor
c. DC compound motor
d. .
6. Project management has :
a. Replaced middle management
b. Became in all business
c. Only in major projects
d. A & b
e. A,b, and c
7. The main difference between MOSFEt and BJT is
a. The geometry in bigger in BJT
b. MOSFET has better gain
c. MOSFET has zero input current.
8. To reduce the load effect of the input using cascaded amplifiers, the input impedance of the 1st
stage shall be
a. Very high
b. Moderate
c. Low.
9. Pipelining help :
a. Latency
b. Throughput
c. Both
10. Dynamic power in integrated circuits can reach
a. 10%
b. 50%
c. 80%
11. Dynamic power consumption in embedded system can be improved by
a. Parallelism
b. Voltage scaling
c.
d. ..
12. Alternator having tv voltage regulation when
a. Over speed
b. Under speed
c. Leading power factor
d. Lagging power factor
13. Number 34 in the following N34 E usually will be specified with
e. Temporary
f. Starting point
g. Traverse
h. Bearing