Workshop Manual Thermo DW 300

Water Heaters Workshop Manual
Thermo 230
Thermo 300
Thermo 350
with control unit 1572
model .30 and up
Thermo 230
Thermo 300
Thermo 350
with control unit 1572D
model .030 and up
Thermo 231
Thermo 301
model .01 and up
Thermo Rail
12/2012
Ident Nr. 9003656C II
Thermo 230 / 231 / 300 / 301 / 350 List of Contents
List of Contents
1. Introduction
1.1 Scope and Purpose ............................................................................................................................... 101

1.2 Applicability of Manual ........................................................................................................................... 101
1.3 Meaning of Warnings, Cautions and Notes ........................................................................................... 101
1.4 Additional Documentation to be used .................................................................................................... 101
1.5 Safety Information and Regulations....................................................................................................... 101
1.5.1 General Safety Notes ................................................................................................................. 101
1.6 Legal Provisions for Installation ............................................................................................................. 102

1.7 Corrections and Improvements.............................................................................................................. 103
2. General Description
2.1 Combustion Air Fan ............................................................................................................................... 202

2.2 Fuel Pump ............................................................................................................................................. 202
2.2.1 Nozzle block preheater............................................................................................................... 203
2.3 Heat Exchanger ..................................................................................................................................... 203

2.4 Combustion Chamber............................................................................................................................ 203
2.5 Control Unit............................................................................................................................................ 203
2.6 Flame Sensor ........................................................................................................................................ 203
2.7 Igniter Box with Igniter Electrodes ......................................................................................................... 203
2.8 Temperature Sensor.............................................................................................................................. 204
2.9 Temperature Limiter .............................................................................................................................. 204
2.10 Overheat Thermostat (Thermo 231 and 301 only) ................................................................................ 204
2.11 Circulation Pump ................................................................................................................................... 204
2.11.1 Aquavent 5000 (U4814) and Aquavent 5000S (U4854) circulating pumps................................ 205
2.11.2 Aquavent 6000C (U4855) and Aquavent 6000SC (U4856) circulating pumps............................205
2.12 Fuel Filter............................................................................................................................................... 206
3. Functional Description
3.1 Switch On .............................................................................................................................................. 302

3.2 Heating Operation.................................................................................................................................. 302
3.3 Switch Off .............................................................................................................................................. 303
3.4 Power Save ........................................................................................................................................... 303
3.5 Auxiliary Heating Operation (heaters with control unit 1572D only) ...................................................... 303
3.6 Heater Lockout (heaters with control unit 1572D only).......................................................................... 303
3.7 Switch-off upon Failure (heaters with control unit 1572)........................................................................ 303
3.8 Switch-off upon Failure (heaters with control unit 1572D) ..................................................................... 305
3.9 Error Code Output (heaters with control unit 1572D) ............................................................................ 306
4. Technical Data
Electrical components...................................................................................................................................... 401

Propellant......................................................................................................................................................... 401
I
List of Contents Thermo 230 / 231 / 300 / 301 / 350
5. Troubleshooting
5.1 General ................................................................................................................................................. 501

5.2 General Fault Symptoms ...................................................................................................................... 501
5.3 Fault Symptoms during Functional Checkouts and Error Code Output or Tests with
Diagnostic Computer, Components Tester or PC Heater Diagnosis .................................................... 503
5.3.1 General ...................................................................................................................................... 503

5.3.2 Fault Symptoms......................................................................................................................... 504
6. Functional Checkouts
6.1 General ................................................................................................................................................. 601

6.2 Adjustments .......................................................................................................................................... 601
6.2.1 Adjustment of CO2 Contents ..................................................................................................... 601
6.3 Components Testing............................................................................................................................. 602
6.3.1 Temperature Sensor Resistance Check.................................................................................... 602

6.3.2 Flame Sensor Resistance Check .............................................................................................. 602
6.3.3 Igniter Electrodes Check ........................................................................................................... 602
6.3.4 Igniter Box Check ...................................................................................................................... 603
6.3.5 Fuel Pump Check ...................................................................................................................... 603
6.3.6 Fan Motor Check ....................................................................................................................... 604
6.3.7 Solenoid Valve Check ............................................................................................................... 604
6.3.8 Nozzle Block Preheater Check .................................................................................................. 604
7. Circuit Diagrams
7.1 General ................................................................................................................................................. 701
8. Servicing
8.1 General ................................................................................................................................................. 801

8.2 Heater Servicing ................................................................................................................................... 801
8.3 Vehicle Servicing .................................................................................................................................. 801
8.4 Heater Test Run.................................................................................................................................... 801
8.5 Maintenance ......................................................................................................................................... 801
8.5.1 Inspection and Attachment of the Exhaust Muffler (only heaters from year of
production 1996 and up to production date 1996, calendar week 36; 3G......) .......................... 801
8.5.2 Burner Head Opening and Closing or Removal and Installation ............................................... 803
8.6 Visual Inspections and Regulations for Installation............................................................................... 804
8.6.1 Connection to Vehicle Cooling System ..................................................................................... 804

8.6.2 Connection to Vehicle Fuel System........................................................................................... 804
8.6.3 Combustion Air Supply .............................................................................................................. 806
8.6.4 Exhaust Line .............................................................................................................................. 806
8.7 Removal and Installation....................................................................................................................... 807
8.7.1 Heater, Removal and Installation .............................................................................................. 807

8.7.2 Temperature Limiter, Replacement ........................................................................................... 807
8.7.3 Temperature Sensor, Replacement .......................................................................................... 807
8.7.4 Burner, Replacement................................................................................................................. 807
II
Thermo 230 / 231 / 300 / 301 / 350 List of Contents
8 7.5 Igniter Box, Replacement ........................................................................................................... 807

8.7.6 Flame Sensor, Replacement ...................................................................................................... 808
8.7.7 Combustion Chamber, Replacement ......................................................................................... 808
8.8 First Operation ....................................................................................................................................... 808
8.8.1 Water Circuit, Bleeding............................................................................................................... 808

8.8.2 Fuel Supply System, Bleeding.................................................................................................... 808
9. Repair
9.1 General .................................................................................................................................................. 901
9.1.1 Work on Components after Disassembly ................................................................................... 902

9.1.2 Incorporation of Modifications..................................................................................................... 902
9.2 Disassembly and Assembly................................................................................................................... 906
9.2.1 Temperature Limiter, Replacement ............................................................................................ 904

9.2.2 Temperature Sensor, Replacement ........................................................................................... 904
9.2.3 Burner, Replacement.................................................................................................................. 904
9.2.4 Combustion Air Fan, Replacement............................................................................................. 906
9.2.5 Control Unit, Replacement ......................................................................................................... 908
9.2.6 Fuel Pump, Replacement ........................................................................................................... 908
9.2.7 High Pressure Nozzle, Replacement...........................................................................................908
9.2.8 Igniter Box, Replacement ........................................................................................................... 910
9.2.9 Flame Sensor, Replacement ...................................................................................................... 910
9.2.10 Heat Exchanger, Replacement................................................................................................... 912
9.2.11 Combustion Chamber, Replacement ......................................................................................... 912
10. Packaging, Storage and Shipping
10.1 General ................................................................................................................................................ 1001
Annex A
Heater, Scheduled Maintenance...................................................................................................................... A-2
III
List of Contents Thermo 230 / 231 / 300 / 301 / 350
List of Figures
301 Functional Sequence (heaters with control unit 1572) .................................................................................... 304
302 Functional Sequence (heaters with control unit 1572D) ................................................................................. 305
501 General Fault Symptoms ................................................................................................................................ 501
701 Automatic Control Circuit with Control Unit 1572 and Switch ......................................................................... 702
702 Automatic Control Circuit with Control Unit 1572 and Timer (Triple Timer) .................................................... 703
703 Automatic Control Circuit with Control Unit 1572D and Switch....................................................................... 704
704 Automatic Control Circuit with Control Unit 1572D and Standard Timer......................................................... 705
705 System Circuit Daimler Chrysler Citaro, Ident.-Nr. 67131................................................................................ 706
706 System Circuit Van Hool, Ident.-Nr. 89401 ...................................................................................................... 707
707 System Circuit O405 / O407 / O408, Ident.-Nr. 91292..................................................................................... 708
708 System Circuit MAN, Ident.-Nr. 89404 ............................................................................................................. 709
709 System Circuit SETRA, Ident.-Nr. 90972 ......................................................................................................... 710
710 Automatic Control Circuit Rail with Control Unit 1572D and Standard Timer and filter heater ........................ 711
801 Swinging Burner Head open ........................................................................................................................... 803

802 Example of a Heater Installation in a Passenger Bus ..................................................................................... 805
901 Temperature Limiter, Temperature Sensor and Burner, Replacement........................................................... 905

902 Combustion Air Fan, Replacement ................................................................................................................. 907
903 Control Unit and Fuel Pump, Replacement..................................................................................................... 909
904 Igniter Box and Flame Sensor, Replacement ................................................................................................ 910
905 Heat Exchanger and Combustion Chamber, Replacement ............................................................................ 912
IV
Thermo 230 / 231 / 300 / 301 / 350 1 Introduction
1. Introduction 1.4 Additional Documentation to be used
This workshop manual contains all information and

1.1 Scope and Purpose procedures necessary for the repair of heaters Thermo
230, 231, 300, 301 and 350 as well as Thermo Rail.
This repair shop manual is intended to support Operating instructions and installation instructions may be
familiarized personnel in the repair of water heaters used as complementary information as necessary.
Thermo 230, 231, 300, 301 and 350.
1.5 Safety Information and Regulations
The water heater may only be operated with the specified
fuel (Diesel or also fuel oil EL) and the relevant designated
type of electrical connection. The general safety regulations for the prevention of
accidents and the relevant operating safety instructions
have to be observed at all times.
1.2 Applicability of Manual "General Safety Regulations" beyond the scope of these
regulations are detailed in the following.
This manual is applicable only for heaters identified on the
title page. The different appearance of control units (see The specific safety regulations applicable to this manual
2.5) allow to distinguish between model .30 and up with are highlighted in the individual chapters by Warnings,
control unit 1572 and the model .030 and up with control Cautions, and Notes.
unit 1572D.
1.5.1 General Safety Notes
In combination with control unit 1572D additionally a
different type of igniter box is installed (refer to 2.7). The year of first operation must be permanently
marked on the identification label by removing the
The heaters Thermo 231 and 301 are variants for vertical relevant number of the year.
installation.
The heaters are cleared for heating the vehicle engine
1.3 Meaning of Warnings, Cautions and and the passenger cabin. The use of the heater in
Notes vehicles not subject to the EU Directive 70/156/EEC (e.g.
ships) is partly governed by regional regulations.
For heaters designed for installation in rail vehicles, type
WARNINGS, CAUTIONS, and NOTES in this manual
approval has been granted (not for Thermo 231 and 301)
have the following meaning:
by the Federal Railway Authority with the type approval
number: EBA 32AZ3/0174/08.
WARNING
This heading is used to highlight that non-compliance with
The heater may only be fitted in vehicles or in independent
instructions or procedures may cause injuries or lethal
heating systems with a minimum coolant capacity of
accidents to personnel.
10 liters.
CAUTION
The heater may only be installed in motor vehicles or in
This heading is used to highlight that non-compliance
independent heating systems with a minimum coolant
with instructions or procedures may cause damage to
capacity of 6 liters.
equipment.
The heater must not be installed in the passenger or driver
NOTE
compartments of vehicles. Should the heater neverthe-
This heading is used to highlight and draw specific
less be installed in such a compartment, the installation
attention to information.
box must be sealed tight against the vehicle interior.
There must be sufficient ventilation of the installation box
from the exterior in order not to exceed a maximum
temperature of 85 C in the installation box. Excessive
temperatures may cause malfunctions.
WARNING
Due to the danger of poisoning and suffocation the
heater must not be operated, not even with timed
operation, in enclosed areas such as garages or
workshops not equipped with an exhaust venting
facility.
101
1 Introduction Thermo 230 / 231 / 300 / 301 / 350
At filling stations and fuel depots the heater must be (Extract from Directive 2001/56/EC Annex VII)
switched off to prevent explosions.
1.7.1. A clearly visible indicator within the user's field of
CAUTION vision must show when the heater is switched on or off.
Where flammable fumes or dust may build up (e.g. in
the vicinity of fuel, coal, wood, cereal depots, or NOTE:
similar installations) the heater must be switched off For further notes and provisions relating to the installation
to prevent explosions. of the heater in vehicles, refer to the installation instruc-
The heater must not be operated near flammable ma- tions.
terials such as dry grass and leaves, cardboard
boxes, paper, etc. IMPORTANT
Failure to follow the installation instructions and the notes
In the vicinity of the water heater a temperature of 110 C contained therein will lead to all liability being refused by
(storage temperature) must not be exceeded under any Spheros. The same applies if repairs are carried out incor-
circumstances (e.g. during body paint work). rectly or with the use of parts other than genuine spare
A violation of this temperature limit may cause permanent parts. This will result in the invalidation of the type appro-
damage to the electronics. val for the heater and therefore of its homologation / EC
type licence.
When checking the cooling water level proceed in
accordance with the vehicle manufacturers instructions. Installation Instructions for Spheros fuel tanks for the fuel
The water in the heating circuit of the heater must contain supply of water heaters in vehicles:
a minimum of 10% of a quality brand anti-freeze.
in busses and trains the installation is not permitted in
Additives in the heating circuit must not affect metals, the passengers or drivers compartment.
plastics and rubber and must leave no deposits. the fuel filler neck must not be located in the passen-
gers or drivers compartment of any vehicle.
The opening pressure in the vehicle cooling system - fuel containers must either be equipped with a vent
normally indicated on the radiator filler cap - must be cap or any other type of ventilation (vent line).
between 0.4 and 2.0 bar above operating pressure (also
applicable to separate heating circuits). Only vent caps in accordance with DIN 73400 may be
used.All fuel containers offered in the Spheros Accesso-
ries Catalogue are suitable for a maximum operating pres-
1.6 Legal Provisions for Installation sure of 0.15 bar overpressure.
All fuel containers offered in the Spheros Accessories Ca-

With effect from 4/03, Type Approvals pursuant to EC Di-
talogue are subjected during manufacture to individual
rectives 72/245/EEC (EMC) and 2001/56EC (Heating Sy-
pressure testing with at least 0.3 bar overpressure.
stems) were granted for the heaters Thermo 230 / Thermo
231 / Thermo 300 / Thermo 301 / Thermo 350 with the fol-
The operational state of the heater, i.e. at least an
lowing EC Type Approval Numbers:
indication "on" or "off" must be easily and clearly visi-
ble.
e1*72/245*95/54*1010*--
e1*2001/56*0007*-- for Thermo 230
For heaters in vehicles not ruled by the EU Directive but
e1*2001/56*0008*-- for Thermo 300
other regulations, the acceptance by the relevant authori-
e1*2001/56*0009*-- for Thermo 350
ty is required as applicable.
e1*2001/56*0010*-- for Thermo 231
e1*2001/56*0011*-- for Thermo 301
Up to 4/03, General Design Certifications existed for these

heaters.I
nstallation is governed above all by the provisions in

Annex VII of Directive 2001/56/EC.
NOTE:
The provisions of these Directives are binding within
the territory governed by EU Directive 70/156/EEC
and should similarly be observed in countries without
specific regulations.
102
Thermo 230 / 231 / 300 / 301 / 350 1 Introduction
1.7 Corrections and Improvements
Deficiencies, improvements, or proposals for correction of

this workshop manual are to be mailed to:
Spheros GmbH
Friedrichshafener Strae 9 - 11
D-82205 Gilching
Telefon: +49 (0)8105 7721 887
Telefax: +49 (0)8105 7721 889
www.spheros.de / [email protected]
103
1 Introduction Thermo 230 / 231 / 300 / 301 / 350
Page empty for notes
104
Thermo 230 / 231 / 300 / 301 / 350 2 General Description
2 General Description The heaters Thermo 230, 231, 300, 301 and 350 basically
consist of
The water heaters Spheros Thermo 230, 231, 300, 301 the combustion air fan
and 350 are used in combination with the vehicles own the fuel pump with nozzle block and nozzle
heating installation to the heat exchanger and
the combustion chamber
heat the passenger compartment the igniter box with igniter electrodes
defrost the windscreen
preheat water-cooled engines For control and monitoring the heater includes
The heaters Thermo 231 and 301 are variants for vertical a control unit
installation. The difference in appearance are the different a flame sensor
identification label and the Z profiles on the installation in- a temperature sensor
terface. a temperature limiter
a temperature limiter without reset button for Thermo
The water heater operates independent from the vehicle 231 and 301 and the Rail variant .126.
engine and is connected to the vehicle cooling system,
the fuel system and the electrical system. An external circulating pump is installed inside the vehicle,
or, in the case of compact units, directly at the heater.
The heater designed to the heat exchanging principle
operates intermittently controlled by the temperature
sensor.
4
3
2 5
Thermo 231/301
6
11 7 1 Burner
2 Coolant inlet
3 Temperature limiter
4 Temperature sensor
5 Coolant outlet
8 6 Heat exchanger
7 Exhaust outlet
10 9
8 Fuel return
9 Combustion air inlet
10 Fuel delivery
Thermo 231/301 11 Splash protection cover
(instead of screen)
201
2 General Description Thermo 230 / 231 / 300 / 301 / 350
2.1 Combustion Air Fan

Solenoid valve Nozzle block
The combustion air fan supplies the air required for pre-heater (optional)
combustion from the combustion air inlet to the combu-
stion chamber.
Fan motor
Splash protection cover
Screen
Fan wheel
Screen Cap
O-ring
The fan consists of a fan motor with fan wheel. Air is taken Fuel Pump
in through a splash protection cover or a screen and the
cap. The heaters Thermo 231 and 301 are provided with
a splash protection cover only.
2.2 Fuel Pump
The fuel pump is responsible for fuel supply.

The pump is driven by the burner motor via a coupling.
Fuel is compressed in the fuel pump to approx. 10 bar and
atomised via the atomiser nozzle.
The solenoid valve integrated into the fuel pump opens
and closes the fuel supply to the atomiser nozzle. Color dots for
Three different fuel pumps are assigned to the different identification
heating capacity classes of the Thermo series. of the heating
These are identified by the heating capacity class specifi- capacity class
cation as well as colour dots:
The fuel pump can be used in dual-line operation (fuel
16 KW: 1 color dot supply and return line).
23-35 KW: 2 color dots
40 KW: 3 color dots If the heater is operated with
a long fuel supply line

check valves in the fuel supply and return line
a fuel filter in the fuel supply line
single-line operation
the fuel supply line must be filled prior to first heater

start-up.
202
2.2.1 Nozzle block preheater
At extremely low temperatures malfunctions may occur

without a nozzle block preheater.
At a temperature of < 0C a thermostat activates the
heater cartridge in the nozzle block. The heating period
depends on the heat reflected within the combustion
chamber. Preheating is deactivated when the thermostat
ambient temperature is +8C.
If the heater is not equipped with a nozzle block preheater

a retrofit is possible.
2.3 Heat Exchanger

Control Unit 1572
IThe heat exchanger transfers the heat generated by
com-bustion to the coolant circuit.
2.4 Combustion Chamber
The fuel/air mix is dispersed in the combustion chamber

for combustion to heat the heat exchanger.
Heat exchanger
Control Unit 1572D
Combustion chamber
2.6 Flame Sensor
The flame sensor continuously monitors the flame

condition during operation. The flame sensor is a photo
transistor changing its resistance depending on the flame
intensity. The signals are supplied to the control unit for
processing.
Flame sensor
2.5 Control Unit

2.7 Igniter Box with Igniter Electrodes
The control unit 1572 or 1572D is the central component
to ensure controlled operation and monitoring of The igniter box generates the high voltage for igniting the
combustion. If the heater has a control unit 1572 installed, fuel/air mix by a high voltage ignition spark across the
a retrofit of control unit 1572D is possible (see Section 9). electrodes.
203
2.10 Overheat Thermostat for burner

Igniter electrodes
(Thermo 231 and 301 only)
Igniter box
Igniter box (green connector
(black connector The overheat thermostat is screwed onto the disk and
cover; mechanically coded)
cover) only in electrically connected to the solenoid valve of the fuel
in combination with
combination with pump. When the burner overheats the thermostat causes
control unit
control unit an error lockout.
1572D
1572
and also
control
unit 1572
2.8 Temperature Sensor
The temperature sensor senses the coolant temperature

at the heat exchanger outlet as an electrical resistance. Overheat Thermostat
This signal is supplied to the control unit for processing.
2.9 Temperature Limiter

2.11 Circulation Pump
The temperature limiter (bimetal) protects the heater
against undue high operating temperatures. The externally mounted circulation pump ensures proper
The temperature limiter can be reset manually. coolant circulation in the vehicle and heater circuit.
The temperature limiter responds at a temperature in Depending on the application, the circulating pump is
excess of 125C to switch off the heater. switched on via the control unit or directly via the vehicle
In the case of Thermo 231 and 301 as well as the Rail electrical system and operated during the entire heater
variant .126, the temperature limiter will trip at a operation duration.
temperature in excess of 105C. The heaters can be operated with the circulation pumps
After the temperature has dropped, an automatic reset will Aquavent 5000 (U4814), Aquavent 5000S (U4854),
occur. Aquavent 6000C (U4855) or Aquavent 6000SC (U4856).
Temperature sensor
Rated power consumption

Operating voltage range
Circulating pump
Rated voltage
Delivery rate
Weight
l/h V= V= W kg
U 4814 5000 12 1014 104 2,1

Aquavent (against 0,2 bar) or or
5000 24 2028
Temperature
limiter U 4854 5000 24 2028 104 2,2
Aquavent (against 0,2 bar)
5000S
U 4855 6000 24 2028 210 2,4

6000C
U 4856 6000 24 2028 210 2,5

6000SC
The circulating pump fuse may never be pulled, while the

pump is running, and may not be replaced, when the
pump is switched on.
204
2.11.2 Aquavent 6000C (U4855) and Aquavent

6000SC (U4856) circulating pumps
The Aquavent 6000C (U4855) andAquavent 6000SC

(U4856) circulating pumps are equipped with a brushless
Aquavent 5000
motor.
(U4814)
NOTE
The Aquavent 6000C (U4855) has a floating-ring type
shaft seal.
The Aquavent 6000SC (U4856) is equipped wit a
magnetic coupling (no seal).
Soft start
The circulating pump motor starts slowly and gently. Max.
Aquavent 5000S rotational speed is only reached after approx. 5 seconds.
(U4854)
Protection against dry running
Protection against dry running is integrated into the
circulating pump motor.
If the circulating pump motor consumes within a time
period of approx. 45 minutes significantly less current, dry
running is detected. The circulating pump motor is
switched off.
After approx. 2 minutes and circulating pump motor
reactivation, the operation can be continued.
Aquavent 6000C
(U4855) Blocking protection
If the pump wheel is blocked, the motor will be switched
off via the error mode directly prior to standstill of the
pump wheel.
Overload protection
Overload protection is activated after the soft start is
completed. The current consumption will be limited.
Aquavent 6000SC In case of hydraulic overpressuring of the circulating
(U4856) pump, the circulating pump motor will not be damaged.
Fehlermodus
In case of malfunctions the circulating pump motor is
switched off via the error mode. After approx. 5 seconds
the error mode switches the circulating pump motor into
energy-saving sleep mode.
Sleep mode
2.11.1 Aquavent 5000 (U4814) and Aquavent In sleep mode internal electronics consumers of the circu-
5000S (U4854) circulating pumps lating pump motor are switched off.
The Aquavent 5000 (U4814) and 5000S (U4854) circula- Reactivation of the circulating pump motor
ting pumps are equipped with a brush motor. It is possible to reactivate the circulating pump motor from
sleep mode. For this purpose the power supply is
NOTE disconnected for > 2 min. After the power supply is
Aquavent 5000 (U4814) with floating-ring type shaft seal. reconnected, the circulating pump motor restarts in soft-
Aquavent 5000S (U4854) uncoupled by a magnet (no start mode.
seal)
Inverse-polarity protection
ATTENTION The circulating pump motor is not equipped with an
The circulating pump motor is not equipped with an internal inverse-polarity protection.
internal inverse-polarity protection.
205
2.12 Fuel Filter
At compact devices of the series 230/300/350.126 and

.190 Rail an optional heatable fuel filter is provided, as an
additional option also for .124 and .155 Rail.
If the electrical filter heating is hooked-up, the temperature
switch turns the integrated filter heating
on at 0,5 2,5 C and
off at 5,5 2,5 C fuel temperature.
206
Thermo 230 / 231 / 300 / 301 / 350 3 Functional Description
3. Functional Description
Activation and deactivation is by means of a

switch
timer
air conditioning
dependent on the type of installation.
For monitoring operation at least an operating indicator

light is provided.
Switch off releases a run-down procedure (see "Switch
off").
The heaters may be

operated with power save for reduced fuel
consumption (see circuit diagram)
equipped or retrofitted with a nozzle block preheater
for extreme low temperatures.
Heaters with control unit 1572D only

When connecting terminal +61 the heaters may operate in
the auxiliary heating mode of operation.
Switching thresholds
Control device Ident. No. 63482E Ident. No. 97810B Ident. No. 63859D
Ident. No. 97806B
Bus Rail Rail
Standard J.E.S
Auxiliary heating
Upper operating point 85C 85C 85C
Lower operating point 78C 70C 75C
Parking heating
Parking heating (economic

setting)
Gradient evaluation Yes Yes Yes

Hysteresis adaption Yes Yes Yes
301
3 Functional Description Thermo 230 / 231 / 300 / 301 / 350
Switching thresholds for Thermo xxx Raill
230.040 230.056 300.124 xxx.126 300.155 350.190

Version Thermo xxx* 350.056 350.155
VOSSLOH VOSSLOH

973 13A 90 162 37x 90 210 12B
Scope of delivery thru 90 162 36A
973 13D 90 162 35A
Heater
Control device 638 59D 679 81C 987 10x 978 04x
Auxiliary heating
Upper operating point 85C 85C 85C 85C
Lower operating point 75C 72C 70C 70C
Parking heating Preheating

Parking heating (economic keeping frost-free

setting)
Gradient evaluation Yes Yes Yes

Hysteresis adaption Yes Yes Yes
Low voltage threshold 18,5V

(20 sec.)
* xxx means 230 or 300 or 350
3.1 Switch On 3.2 Heating Operation
Upon switch on the operating indicator light goes on. After reaching operating temperature the control unit
Combustion air fan, fuel pump and circulation pump start takes over to provide controlled operation by activation
operation. (If fitted and temperature is < 0 C nozzle block and deactivation of the burner in order to maintain a nearly
preheater is also activated). constant temperature of the heat exchanger (coolant).
After approximately 12 seconds (run-up time) the high The heating operation is terminated as soon as the upper
voltage igniter spark is available. Approximately 1 second operating point is exceeded.
later the solenoid valve in the fuel pump opens and the The heater now is in the control idle period. Heater
nozzle sprays fuel into the combustion chamber to be operation is resumed when the temperature drops below
ignited by the igniter spark. A photo control circuit the lower operating point.
deactivates the igniter box after flame-up.
302
Heaters with control unit 1572D only burner after control idle period is raised above that for
Gradient evaluation normal operation and is automatically shifted up or down
In case of low coolant flow or poor coolant circuit venting dependent on the combustion time of the heater
the temperature quickly increases in heating operation. (hysteresis adaptation).
If gradient evaluation exists, the control unit recognises
the quick temperature increase and automatically sets the Hysteresis adaptation (example)
upper switching threshold to a lower value. This prevents After the first control idle period, the lower operating point
residual heat triggering the overheating protection. is 78C.
Combustion operation is started when the temperature
Control idle period falls below this threshold.
A rise in temperature above the upper switching point The length of combustion time until the upper operating
makes the solenoid valve in the fuel pump shut off the fuel point is exceeded should be 120 seconds.
supply initiating the run-down. The flame extinguishes, If combustion lasts more than 120 seconds, the lower
the combustion air fan and the circulation pump however operating point is increased by 1 Kelvin, up to max. 80C.
continue their operation. After approximately 90 seconds If combustion time is less than 120 seconds, the lower
(120 seconds for heaters with control unit 1572D) operating point is lowered by 1 Kelvin, down to minimally
run-down is completed with deactivation of the 70C.
combustion air fan.
The circulation pump remains in operation during the

control idle period. The operating indicator light is on.
3.6 Heater Lockout (heaters with control
unit 1572D only)
3.3 Switch Off
After the heater has performed eight start attempts due to
Switching off the heater stops combustion. The operating a malfunction or after five subsequent flame-outs the
indicator light goes out and run-down commences. The heater enters a lockout and start attempts are suspended.
combustion air fan and circulation pump are deactivated This lockout is superior to the normal error lockout.
after approximately 90 to 120 seconds (120 seconds for Unlocking is performed by starting the heater and
heaters with control unit 1572D). disconnection of the main power supply of the heater
during error run-down.
Reactivation of the heater during run-down is permitted.
The burner immediately resumes operation after the
run-up time.
3.7 Switch-off upon Failure (heaters with
control unit 1572)
3.4 Power Save
The heater switches off automatically when detecting one
of the following malfunctions.
With power save on the control temperatures of the
heating circuit are kept low. Combustion performance is The operating indicator light goes off. Combustion air fan
not reduced. and circulation pump are deactivated after approximately
90 to 120 seconds.
This results in a reduced heat radiation loss when limited
heating performance is required (e.g. in heat hold opera- Malfunctions during switch-on
tion) cutting down fuel consumption. short or open circuit of temperature sensor.
short or open circuit of flame sensor.
open circuit of solenoid valve.
Malfunctions during start-up:

3.5 Auxiliary Heating Operation (heaters flame detected by photo control circuit prior to high
with control unit 1572D only) voltage igniter spark.
no flame detected after approximately 25 seconds
after heater start.
When terminal +61 is connected and powered (engine is
running), the heater operates in the auxiliary heating Malfunctions during heating operation:
mode. low voltage threshold of approximately 20V violated
The power save mode is during auxiliary heating automa- for a duration of 12 seconds.
tically deactivated by the control device. no combustion for more than 10 seconds.
The lower temperature threshold for reactivation of the
303
A H1 Operating indicator light

B E1 Heater cartridge
C M2 Circulation pump
7
D U1 Igniter box
3 5 3 E M1 Combustion air fan
1 2 6 8 2 9 6 10 F Y1 Solenoid valve
A G B1 Flame sensor
B
1 Switch on
C
2 Start
D 3 Combustion operation
5 Temperature sensor upper switching
E
threshold
F 6 Flame sensor dark
G 7 Control idle
8 Temperature sensor lower switching
threshold
12s 1s 1s 12s 30s 90s 12s 1s 1s 12s 30s 90s 9 Switch off
max. max. 10 Heater off
12 14 16 12 14 16
11 Nozzle block preheater
13 15 13 15
12 Start-up
11 13 Foreign light check
14 Pre-ignition
15 Safety period
16 Run-down
Fig. 301:Functional sequence (heaters with control unit 1572)
temperature sensor short circuit during control idle. Malfunctions by overheating:

temperature sensor open circuit during combustion. Overheating results in deactivation of the heater by the
flame sensor short circuit during combustion. temperature limiter. After cool down of the unit and
solenoid valve short circuit during combustion. correction of the fault the button of the temperature limiter
must be reset.
Malfunctions during run-down:
Detection of a flame after more than 30 seconds after start An error reset for a new start standby is achieved by
of run-down with the circulation pump and combustion air switching the heater off and on again.
fan maintaining operation for the following 90 seconds.
304
A H1 Operating indicator light

C M2 Circulation pump
D U1 Igniter box
7
E M1 Combustion air fan
F Y1 Solenoid valve
3 5 3
1 2 6 8 2 9 6 10 G B1 Flame sensor
A
1 Switch on
C 2 Start
D 3 Flame-up, combustion operation
5 Temperature sensor upper switching
E threshold
6 Flame sensor dark
F
7 Control idle
G 8 Temperature sensor lower switching
threshold
9 Switch off
max. max. max. max.
12s 1s 1s 12s 30s 12s 1s 1s 12s 30s 10 Heater off
12 Start-up
12 14 max. 12 14 max. 13 Foreign light check
13 15 120s 13 15 120s
14 Pre-ignition
16 16
15 Safety period
16 Run-down
Fig. 302:Functional sequence (heaters with control unit 1572D)
3.8 Switch-off upon Failure (heaters with short/open circuit or dry run (if programmed) of
control unit 1572D) circulation pump.
When using the circulation pump U 4851 approxi-
mately 15 seconds after switch-on the circulation
The heater switches off automatically when detecting one
pump is automatically stopped and may only be
of the following malfunctions.
reactivated after approximately 2 minutes should
Several subsequent switch-offs due to a malfunction will
coolant be missing or the pump wheel be seized.
cause the heater to enter an error lockout condition.
Malfunctions during heating operation:
Flash pulses are output via the operating indicator light.
low voltage threshold of approximately 21V violated
The combustion air fan and the circulation pump are
for a duration of 20 seconds.
switched off after approx. 120 seconds.
no combustion for more than 10 seconds.
temperature sensor short or open circuit.
Malfunctions during switch-on:
flame sensor short or open circuit.
Short or open circuit of
solenoid valve short or open circuit.
temperature sensor
flame sensor
Malfunctions during heating operation:
burner motor
(valid for application Thermo 350.190)
solenoid valve
low voltage threshold of approximately 18,5V violated
igniter box
for a duration of 20 seconds.
no combustion for more than 10 seconds.
Malfunctions during start-up:
temperature sensor short or open circuit.
short circuit of igniter box
flame sensor short or open circuit.
open circuit of igniter box
solenoid valve short or open circuit.
flame detected by photo control circuit prior to high
voltage igniter spark.
no flame detected after approximately 25 seconds
after heater start.
305
Malfunctions during run-down: 3.9 Error Code Output (heaters with

Detection of a flame after more than 30 seconds after control unit 1572D)
start of run-down with the circulation pump and
combustion air fan only maintaining operation for the follo-
When equipped with a standard timer an error code
wing 90 seconds.
readout appears on the display of the timer after a
malfunction.
Malfunctions by overheating:
Overheating results in deactivation of the heater by the NOTE
temperature limiter/thermostat. Dependent on heater When the heater is operated by means of a switch the
configuration: type of error is output during heater run-down via a flash
the reset button on the temperature limiter must be code of the operating indicator light. After five short
reset. signals the long flash pulses are counted. The flash
the reset of the thermostat is performed automatically pulses correspond to the error number in the following
after cool down. table:
An error reset for a new start standby is achieved by F 01 no start

switching the heater off and on again. F 02 flame-out *
Malfunctions by overheating of the burner F 03 low voltage or excess voltage

(Thermo 231 and 301): F 04 foreign light detected during run-up and run-down
Overheating of the burner causes the overheat thermostat
to initiate an error lockout at 150C. F 05 flame sensor defective
The solenoid valve closes, the fuel supply is cut off and a F 06 temperature sensor defective
run-down is launched. An auto-reset occurs after cool-
down of the thermostat. F 07 solenoid valve defective
F 08 fan motor defective
F 09 circulation pump defective **
F 10 temperature limiter defective / overheating
F 11 igniter box defective
F 12 error lockout due to repeated malfunction or
repeated flame-out
(8x no start-up or 5x flame-out)
* A response of the overheat thermostat will be stored
in the control unit as a flame-out (F 02) (Thermo 231
and301).
** The error 09 is indicated only if the heater is equipped
with a circulation pump monitoring (see table below).
Table: Programmed SG1572D with integrated circulation

pump monitoring
EOL-Data record for SG 1572D

EOL- Circulation pump monitoring Ctr. device
Data record Yes No programmed
63317F
63860E
67980D X 67981D
96774B
97805C
97807C X 97810C
97809C X 97810C
97811B X 97812A
97813A
97815A
306
Thermo 230 / 231 / 300 / 301 / 350 4 Technical Data
4. Technical Data
Where no threshold values are specified technical data

are understood to include standard tolerances for heater
units of 10% at ambient temperature of + 20 C and at
nominal voltage.
Electrical components
Control unit, fan and circulation pump motors, solenoid

valve, igniter box, heater cartridge, nozzle block preheater
and timer are 24V components. Temperature limiter,
flame sensor, temperature sensor and switches are
voltage independent components.
NOTE
The allocation of circulation pumps to heater units must be
in accordance with coolant resistances.
Propellant
The suitable propellant is the Diesel fuel specified by the

vehicle manufacturer.
Only the type of fuel indicated on the identification plate

may be used. Also Diesel fuel with an addition of 5% PME
(vegetable oil methyl ester), class EL fuel oils (not fuel oil
L) or petroleum may be used if their quality is in accordan-
ce with the German standard.
A bad influence caused by additives is not known.
When using fuel out of the vehicle tank the information

about additives of the vehicle manufacturer must be ob-
served.
When using fuel out of a separate fuel tank and at tempe-

ratures below 0C, winter Diesel fuel must be used.
The use of flow improvers is permitted.
Mixing ratio for separate fuel tank and temperature below

0C.
Temperature Winter Diesel Additive petrole-

fuel um or petrol
0 C to 20 C 100 %
20 C to 30 C 70 % 30 %
or special low temperature
Diesel fuel
30 C to 40 C special low temperature
Diesel fuel or 100 % petroleum
401
4 Technical Data Thermo 230 / 231 / 300 / 301 / 350
Heater Thermo 230 Thermo 231 Thermo 300 Thermo 301 Thermo 350
Type Thermo 230 Thermo 231 Thermo 300 Thermo 301 Thermo 350
Mark of conformity up to 4/03 ~ S230 ~ S327 ~ S229 ~ S328 ~ S228
EC type approval number e1*2001/56* 0007*-- 0010*-- 0008*-- 0011*-- 0009*--
Heater principle High pressure atomizer
Heating flow KW 23 30 35
(kcal/h) (20 000) (26 000) (30 000)
Fuel Diesel / fuel oil
Fuel consumption kg/h 2.9 3.3 3.7
Nominal voltage V- 24
Operating voltage V- 20 ... 28
Operating voltage V-
19 ... 28
Nominal power consumption W
65 110 140
(without circulation pump)
Permissible operating ambient
temperature range C 40 ... +85
(heater, control unit, circulation pump)
Permissible storage temperature C +110 max.
Permissible operating overpressure bar 0.4 ... 2.0
Heat exchanger capacity l 1.8
Minimum capacity of circuit l 10.00
CO2 in exhaust at nominal voltage Vol.-% 10 0.5 related to 500 m above S.L.
CO2 in exhaust at nominal voltage Vol.-%
9,2 ... 10,1
Dimensions heater mm length 610
(tolerance 3 mm) mm width 246
mm heigh 220
Weight kg 19
402
Thermo 230 / 231 / 300 / 301 / 350 4 Technical Data
Circulation pump U 4814 U 4854 U 4855 U4856

Aquavent 5000 Aquavent 5000S Aquavent 6000C Aquavent 6000SC
Volume flow I/h 5000 (against 0,2 5000 (against 0,2 6000 (against 0,4 6000 (against 0,4
bar) bar) bar) bar)
Nominal voltage V= 12 or 24 24 24 24
Operating voltage range V= 10...14 / 20...28 20...28 20...28 20...28
Nominal power consumption W 104 104 210 210
Dimensions Lenght 230 Lenght 249 Lenght 226 Lenght 231

Width 100 Width 100 Width 115 Width 115
Height 103 Height 105 Height 118 Height 118
Weight kg 2,1 2,2 2,4 2,5
Optional Fuel Filter Heater
Filter Heater
Nominal power consumption W 240
Nominal voltage V- 24
Switch-on point C 0,5 2,5
Switch-off point C 5,5 2,5
403
4 Technical Data Thermo 230 / 231 / 300 / 301 / 350
404
Thermo 230 / 231 / 300 / 301 / 350 5 Troubleshooting
5 Troubleshooting CAUTION
Troubleshooting is normally limited to the isolation of
defective components.
5.1 General The following possible causes for trouble have not been
taken into consideration and must always be excluded
This section describes troubleshooting procedures for the as a possible cause for malfunction:
heaters Thermo 230, 231, 300, 301 and 350.
corrosion on connector
CAUTION loose contact on connector
Troubleshooting requires profound knowledge about wrong crimping on connector
components and their theory of operation and may only be corrosion on wiring and fuses
performed by trained personnel. corrosion on battery terminals
In case of doubt functional interrelations may be derived After any fault correction a functional checkout in the
from Sections 2 and 3. vehicle has to be performed.
5.2 General Fault Symptoms
The following table (Fig. 501) lists possible fault

symptoms of general nature.
Symptom Probable Cause
Fault in electrical system
Operating indicator light is not on, no heater operation. no power supply

fuses
wiring to terminals of connector A of control unit.
Fuse F2 blows. Short circuit in circulation pump or in wiring to heater.
Fuse F3 blows. Short circuit in wiring to heater/motor/nozzle block

preheater (if installed).
Normal heater operation, operating indicator light is out. Operating indicator light defective or wiring to light open
or shorted.
Fault in water system
Circulation pump not operating Failure mode activated

(U 4851 and Aquavent 6000 S only)
The failure mode switches the motor off in case of mal-
functions. After approx. 5 sec the failure mode switches
the motor to the power saving sleep mode.
In the sleep mode the internal consumers of the motor

electronics are switched off. The power consumption in
this mode then amounts to < 2 mA.
The motor can be reactivated out of the sleep mode by

disconnection of the power supply for approx. 2 minutes.
After power reconnection the motor will again run up with
a soft start.
Fig. 501 General Fault Symptoms (Sheet 1 of 3)
501
5 Troubleshooting Thermo 230 / 231 / 300 / 301 / 350
Heater operation stops because heat exchangers Rate of flow too low, because
connected do not dissipate enough heat. air in heater, in heat exchangers or in system
sections.
cocks (flow regulator) throttled, contaminated or
closed.
contamination in system, e.g. in areas of restricted
flow.
circulation pump rate of delivery insufficient (air in
pump housing).
wrong sense of rotation check wiring colors
(black + / brown ).
not enough anti-freeze.
excessive system resistance (especially high when
cold).
circulation pump defective.
Heat exchanger dissipate not enough heat,

because
air in heat exchangers or in system sections.
contaminated heat exchanger surfaces (external).
insufficient air intake or exit.
fan: rate of delivery low / wrong sense of rotation /
resistance too high.
too much anti-freeze.
heat exchanger of too low capacity.
Rough calculation of rate of flow
heat flow [kW] acc. to ident. label

Rate of flow in [l/h] = x 860
temperature difference t in [K] or [C]
measured between heater water inlet and outlet
(e.g. with contact thermometer)
Fault in fuel supply
No fuel delivery to heater. fuel tank empty.

kinked, closed, contaminated or leaking lines.
paraffin deposits or water captured in fuel filter or fuel
lines.
vent in tank clogged.
fuel lines interchanged.
fuel filter contaminated.
fuel screen in pump contaminated.
502
Wrong combustion
CO2 value cannot be set to rated value, air bubbles in suction line (suction line leaking).
combustion irregular. fuel filter contaminated or leaking.
fuel system integration leak (suction height, low
pressure in tank); observe installation instructions.
fuel pump defective (pump pressure).
return line throttled.
filter screen in pump contaminated.
O-ring sealing on fuel pump no longer effective
(ageing)
nozzle jet defective.
combustion air or exhaust lines throttled or closed.
fan motor speed too low.
5.3 Fault Symptoms during Functional Operation of the diagnostic computer is menu controlled
Checkouts and Error Code Output or by means of four push button switches.
Tests with Diagnostic Computer,
For details refer to operating instructions for "Diagnostic
Components Tester or PC Heater Computer".
Diagnosis
Components Tester
5.3.1 General
NOTE
Error Code Output Checks with the components tester may only be
performed on heaters equipped with control unit 1572.
NOTE
Only heaters with a control unit 1572D provide an error Using the components tester several types of faults and
code output. component malfunctions may be analyzed in the vehicle.
When equipped with a standard timer an error code The test of the individual components with the compo-
readout is available after a malfunction on the display of nents tester is not intended. Faults like short or open
the timer. circuits may be detected with the components tester but
When the heater is operated by means of a switch a cannot be localized.
coded flashing of the operating indicator light during
run-down of the heater or until switch-off indicates the For details refer to operating instructions for "Components
type of error (see 3.9). Tester".
Diagnostic Computer PC Heater Diagnosis
NOTE By use of the PC heater diagnosis heaters (with control

Checks with the diagnostic computer may only be unit 1572 or 1572D) may be tested in the vehicle.
performed on heaters equipped with control unit 1572.
For details refer to operating instructions for "PC Heater
By use of the diagnostic computer heaters may be Diagnosis".
checked in the vehicle. The following tests are available:
indication of measured values: water temperature,

control unit supply voltage, flame sensor bright/dark.
indication and erasure of faults stored in the control
unit.
503
5.3.2 Fault Symptoms to a malfunction, the heater enters an error lockout and
stops any further attempts to start. This error lockout is
5.3.2.1 Fault Symptom "No Start" superior to the normal error lockout condition.
The error lockout reset is achieved by switching the heater
NOTE on and disconnection of the heater power supply during
Heaters with control unit 1572D: run-down.
If the heater performs 8 consecutive attempts to start due
NO
Switch on heater. Motor and fan wheel Is fan wheel caught Is voltage present on Check fuses F1/F2/F3
Is combustion air fan free to move? in cap? plug contact A3? and relais K1, K2 and
operating? replace as required
(control unit 1572
only).
Does trouble persist?
Check motor electrics Replace cap Is voltage too low? Check electrical
YES and replace as and fan wheel. Rated value >20,5 volts wiring and
required. ( 0,5 volts) connections.
Does trouble persist?
Low voltage switch Control unit defective,

off during start-up. replace.
Check battery.
Is fuel free of bubbles Is fuel filter Fuel suction line Fuel lines empty? Are O-rings in fuel
in supply and return? contaminated? leak? pump?
Is pump mounted
securely?
Replace fuel filter. Retighten line Repeat start (several Fuel pump defective,
connections, times if necessary) replace.
replace lines as until lines are filled.
required.
Is solenoid valve Connect solenoid

connected to valve.
electrics?
Is gap between igniter Check gap between

electrodes ok? igniter electrodes.
Is nozzle free of foreign Replace nozzle.

matter and deposits
and properly secured?
Is viewing glass of Clean window and

flame sensor viewing glass.
contaminated?
504
5.3.2.2 Fault Symptom "Flame-out" stops any further attempts to start. This error lockout is
superior to the normal error lockout condition.
NOTE The error lockout reset is achieved by switching the heater
Heaters with control unit 1572D: on and disconnection of the heater power supply during
If the heater performs 5 consecutive attempts to start due run-down.
to a malfunction, the heater enters an error lockout and
NO
Switch on heater. Electrical power Replace defective

Is combustion air fan supply, electrical
operating? fuses, plug contacts, components.
relays o.k.?
(control unit 1572
only)
Is fuel free of bubbles Is fuel filter contaminated Is fan wheel free to Check cap, motor and
YES in supply and return? or jellied? move? fan wheel.
Replace filter and check fuel low Is motor o.k.? Replace motor.
temperature rating.
Thermo 231/301 Is solenoid valve o.k.?

No fuel supply. (5.3.2.7) Control unit defective,
replace.
Is viewing glass of Clean window and

flame sensor viewing glass.
contaminated?
Is nozzle free of Replace nozzle.

foreign matter and
deposits?
5.3.2.3 Fault Symptom "Low Voltage"
NO
Is voltage present on plug contact A3? Is electrical wiring Make electrical

o.k.? connections.
Disconnect heater from battery supply.

Is battery properly charged?
Control unit defective,
YES replace.
Connect heater.
Is voltage between plug contacts A3 and A6
approx. 0.5 volts less than on battery?
Is electrical power supply line Replace power supply

to heater o.k.? line.
Control unit defective, replace.
505
5.3.2.4 Fault Symptom "Foreign Light Detection

during Run-up or Run-down"
NO
Has heater been in long time operation Flame sensor defective, replace.
shortly before ? Control unit defective, replace.
Allow heater to cool down and restart (approx. 2 min.). Clean combustion tube.
Does same symptom show again? Remove coke deposits.
YES
Flame in run-down. Control unit defective, replace.
Replace solenoid valve.
5.3.2.5 Fault Symptom "Flame Sensor Defective"
NO
Flame sensor defective, replace.
If replacement of flame sensor does not cure

the problem, replace control unit.
YES
5.3.2.6 Fault Symptom "Temperature Sensor

Defective"
NO
Are electrical lines and contacts to and on Make contacts or replace component.
temperature sensor o.k.?
WARNING: loss of water!
Temperature sensor defective, replace.

YES WARNING: Water may escape!
If replacement of temperature sensor does not cure

the problem, replace control unit.
506
5.3.2.7 Fault Symptom "Solenoid Valve Defective"
NO
Is solenoid valve supplied Make electrical connections.

with electrical power ?
Has safety thermostat responded ? Safety thermostat defective,

(Thermo 231/301 only) replace.
YES
Investigate reason for response

(e.g. check exhaust system)
Is components test with diagnostic computer o.k. Control unit defective, replace.
(audible click of solenoid valve)?
Does fuel leak from nozzle in run-down?
507
5.3.2.8 Fault Symptom "Temperature Limiter

Defective"
NO
Is electrical power supply Make electrical connections.

to components o.k.?
Has temperature limiter responded? Control unit defective, replace.

(Reset according to type of temperature limiter)
YES
Determine why temperature limiter has responded,

e.g.:
check shut-off elements,
check water circulation in system is free from
bubbles,
check circulation pump sense of rotation,
check coolant low temperature resistance.
Can no fault be detected?
Replace temperature limiter.
If symptom shows again after testing:

control unit defective, replace.
508
Thermo 230 / 231 / 300 / 301 / 350 6 Functional Checkouts
6 Functional Checkouts
6.1 General
This section describes the tests and adjustments on the

heater in installed and removed condition to prove its
serviceability.
WARNING
The heater must not be operated in closed areas like
garages or workshops with no exhaust ventilation
facilities.
To prevent fires do not switch heater on with burner
swung open.
Fastening screw
6.2 Adjustments
6.2.1 Adjustment of CO2 Contents

loosen fastening screw (refer to Fig.) and reposition
It is allowed to change the manufacturers setting for
setting ring with fastening screw until rated value is
combustion air quantity by rotation of the setting ring.
obtained.
tighten fastening screw with 1.0 +0.5 Nm and apply
Measurement of the CO2 value of the exhaust gas must
screw seal varnish.
be performed followed by an adjustment of the combusti-
on air quantity as required in case of:
NOTE
repairs on the burner
CO2 setting depends on fuel (viscosity) and on geodetic
irregularities in combustion
altitude (0.1 % per 100 m).
functional checkouts
If proper setting cannot be obtained or when exceeding
nozzle replacement
smoke spot number, proceed as follows:
check burner head air side for damage and replace if
required
Setting procedure
check fuel pump pressure and replace pump if
measure control unit power supply voltage
required
operate heater for approximately 5 min.
check fuel filter and strainer in fuel pump for contami-
measure CO2 contents and smoke spot number and
nation and replace if required
compare with relevant diagram
adjust pressure
replace fuel nozzle
measure burner motor speed
14
13
12
11
10
9
CO2 (Vol.-%)
6
18 20 22 24 26 28 30 32
Voltage
CO2 - setting at 500 m NN
601
6 Functional Checkouts Thermo 230 / 231 / 300 / 301 / 350
6.3 Components Testing 6.3.3 Igniter Electrodes Check
6.3.1 Temperature Sensor Resistance NOTE

The insulator of the igniter electrodes must show no
Check damage. Igniter electrodes not working properly must be
replaced.
When checking the temperature sensor with a digital
multimeter the values of the following diagram must be Check
obtained. Resistance checking is preferably performed at inspect insulators of igniter electrodes for damage
ambient temperatures between 20 C and approximately
100 C (immerse sensor in water).
R/y
10000
Resistance (Ohm)
5000
20 C 4419 ..... 4892 W
1000 100 C 319 ..... 348 W

T/C
10 50 100
Water temperature C
6.3.2 Flame Sensor Resistance Check
NOTE
The glass bulb of the flame sensor and the viewing glass
of the window (refer to Fig.) are to be cleaned if contami-
nated. In case of damage or not obtaining the rated values
replace flame sensor.
Check
cover flame sensor glass bulb
check resistance (rated value: < 20 kOhm)
uncover flame sensor glass bulb and expose to light
of strong lamp.
check resistance (rated value: < 400 Ohm)
Viewing glass
Glass bulb
602
Thermo 230 / 231 / 300 / 301 / 350 6 Functional Checkouts
6.3.4 Igniter Box Check 6.3.5 Fuel Pump Check
NOTE 6.3.5.1 Fuel Pump Check on Heaters with Control Unit

The igniter box may also be tested using the PC heater 1572
diagnosis (component test).
A test gauge is required for performing the test. Such a
WARNING gauge (with a range from 0 to 15 bar) can be procured
High voltage; 20.000 volts arcing across the igniter from your authorized Spheros dealer.
electrodes. The fuel pump and the fuel hoses must be replaced every
5 years.
CAUTION
Do not apply voltage to igniter box without electrodes.
CAUTION
Check The electronic ignition coil must be removed for safety
apply 24 V as shown on figure reasons.
normal condition: spark between electrodes.
Check
remove igniter box (refer to 9.2.7.1).
Igniter electrodes 20.000 V remove nozzle.
NOTE
screw on tester.
Igniter box (black
cover flame sensor.
connector cover)
switch on heater.
only in combination
after approximately 13 sec. pump pressure is
with control unit
indicated (refer to diagram).
1572
switch off heater.
unscrew tester.
CAUTION
Do not damage nozzle bore.
screw in nozzle and torque with 20 Nm.

install igniter box (refer to 9.2.7.2).
NOTE Igniter electrodes 20.000 V

Igniter box
(green connector cover;
mechanically coded)
in combination with
control unit
1572D and 11
also with
Pump pressure (bar)
10,5
control unit
1572 10
9,5
Thermo 350
9
Thermo 300/301
8,5
Thermo 230/231
8
2500 3000 4000 5000 6000 7000 8000 8500
-1
Speed (min )
Pump pressure in relation to speed
603
6 Functional Checkouts Thermo 230 / 231 / 300 / 301 / 350
6.3.5.2 Fuel Pump Check on Heaters with Control Unit 6.3.7 Solenoid Valve Check
1572D
NOTE
NOTE A solenoid valve leaking valve seat shows by rather long
On heaters with control unit 1572D the fuel pump may smoke emissions during run-down. In this case fuel keeps
only be checked by means of the PC heater diagnosis. dripping through the fuel nozzle.
The fuel pump and the fuel hoses must be replaced every Short smoke emissions are normal caused by clearing the
5 years. area between solenoid valve and nozzle bore.
Check
6.3.6 Fan Motor Check
CAUTION
NOTE Disconnect solenoid valve connector from control unit to
The fan motor check is performed with the burner avoid damage to the control unit.
installed. If normal conditions are not obtained the fan
motor must be replaced. Check electrics for the following values:
break voltage 17.0 Volts
Check operating voltage 19.2 ... 28.8 Volts
check fan motor bearing condition(binding) power consumption at
measure heater power supply voltage nominal voltage and 20 C 10 Watts
switch on heater nominal current 0.42 Amps
measure speed and compare with the diagram below
Thermo 230/231 4400 350 24 Volt NOTE
Thermo 300/301 5200 420 24 Volt With all variants of the control unit the solenoid valve may
Thermo 230/301 6200 500 24 Volt also be checked by means of the PC heater diagnosis
(component test).
8000 Thermo
350
6.3.8 Nozzle Block Preheater Check
7500
NOTE
7000 At a temperature of < 0 C the heater cartridge in the
6500
Thermo nozzle block is activated. The heating period depends on
300/301
the heat reflected within the combustion chamber.
6000 Preheating is deactivated when the thermostat ambient
5500
Thermo
230/231
temperature is +8 C.
Power consumption is 130 13 Watts at 24 Volt.
5000
4500
Check
swing burner head open or remove
Speed (1/min.)
4000 disconnect electrical connector

connect ohmmeter to connector
3500
using cooling spray cool down thermostat or bridge
3000 resistance (max. 4.5 ).
2500
18 20 22 24 26 28 30 32
Voltage
604
Thermo 230 / 231 / 300 / 301 / 350 7 Circuit Diagrams
7 Circuit Diagrams
7.1 General
The circuit diagrams (Fig. 701 and 702) show possible The circuit diagrams (Fig. 705 through 710) show possible
heater circuits for Thermo 230, 300 and 350 with control variants of heater circuits for Thermo 230, 231,300, 301
unit 1572 and with and 350 with control unit 1572D.
switch
timer 1529 (triple timer)
The circuit diagrams (Fig. 703 and 704) show possible

heater circuits for Thermo 230, 231, 300, 301 and 350
with control unit 1572D and with
switch
standard timer 1531
701
7 Circuit Diagrams Thermo 230 / 231 / 300 / 301 / 350
A
6 1
30 30 5 2
4 3
F3 F2
S2
S4
1 D
S1 X3 4 3 2 1
gn
or
br
gr
S3
D X1
X1 A 3 2 1 4
1 2 3
1 sw 5
4 5 6
5 or 1
rt/ws X3
1 3 5 7
3 3 X2
1
K1 A2
2
2 4 6 8
4 rt 4
2 br 6
M1 U1 F1/B3 B2 K2
6 bl 2
1 br B4
H1 M2 M + SE - H2
2 sw C U1 M F1
A2 B1 Y1 E1 A1
E1 M1 Y1 B2 B1
X2 U2 B3
A1
br
31 31
Wire colors
bl blue
br brown
ge yellow
1 Diagnostic connector gn green
Wire gauges
gr gray
< 7.5 m 7.5 - 15 m or orange
0.75 mm2 1.5 mm2 rt red
1.0 mm2 1.5 mm2 sw black
1.5 mm2 2.5 mm2
vi violet
2.5 mm2 4.0 mm2
4.0 mm2 6.0 mm2
ws white
Item Nomenclature Remark Item Nomenclature Remark

A1 Heater not grounded S3 Switch, external trigger
circulation pump
A2 Control unit SG 1572
B1 Flame sensor S4 Switch power save operation
B2 Temperature sensor U1 Igniter box
B3 Temperature limiter U2 Igniter electrodes
B4 Thermostat open at T > 8 C A Plug connections, 6-pole
E1 Heating cartridge for nozzle preheating C Plug connections, 1-pole
F2 Fuse 25A flat fuse SAE J 1284 D Plug connections, 4-pole
F3 Fuse 25A flat fuse SAE J 1284 X1 Plug connections, 6-pole
H1 Light operation indicator light X2 Plug connections, 2-pole
K1 Relay (in item A2) for circulation pump X3 Plug connections, 8-pole
K2 Relay (in item A2) for combustion air fan / Y1 Solenoid valve
heating cartridge
M1 Motor combustion air fan

M2 Motor circulation pump
S1 Switch on / off
S2 Continuity switch on water cock
Fig. 701 Automatic Control Circuit with Control Unit 1572 and Switch
702
A
58 58 6 1
75(15) 75(15)
30 30 5 2
4 3
F3 F6 F2
S4
S2 S3 1 D
X3 4 3 2 1
gn
or
br
gr
4 2
D X1
X1 A
3 1 5
3 2 1 4
1 2 3
sw
8 4 6 2 4 5 6
5 or 1
P X3
rt/ws 1 3 5 7
7 3 3 X2
H3 H4 1
3 K1 A2
2
5 X4 2 4 6 8
4 rt 4
X4
2 br 6
M1 U1 F1/B3 B2 K2 8 7 6 5 4 3 2 1
6 bl 2
1 br B4
M2 M + - H2
2 sw C SE
U1 M F1
A2 B1 Y1 E1 A1
E1 M1 Y1 B2 B1
X2 U2 B3
A1
br
br
31 31
Wire colors
bl blue
br brown
1 Diagnostic connector ge yellow
gn green
Wire gauges
2 to vehicle terminal +75 if available, otherwise terminal 15 gr gray
< 7.5 m 7.5 - 15 m or orange
3 Timer P: 0.75 mm2 1.5 mm2 rt red
with plus to connection 4 = continuous operation during immediate heating 1.0 mm2 1.5 mm2 sw black
without plus to connection 4 = heating period 1 hour 1.5 mm2 2.5 mm2
vi violet
2.5 mm2 4.0 mm2
4 vehicle lighting terminal 58 4.0 mm2 6.0 mm2
ws white

A1 Heater not grounded S2 Continuity switch on water cock
A2 Control unit SG 1572 S3 Switch, external trigger
circulation pump
B1 Flame sensor
S4 Switch power save operation
B2 Temperature sensor
U1 Igniter box
B3 Temperature limiter
U2 Igniter electrodes
B4 Thermostat opens at T > 8 C
A Plug connections, 6-pole
E1 Heating cartridge for nozzle preheating
C Plug connections, 1-pole
F2 Fuse 25A flat fuse SAE J 1284
D Plug connections, 4-pole
X1 Plug connections, 6-pole
H3 Light in item P symbol lighting
H4 Symbol for Heating in Display symbol lighting (in item P)
K1 Relay (in item A2) for circulation pump
Y1 Solenoid valve
K2 Relay (in item A2) fo combustion air fan /
heating cartridge
P Triple timing clock (1529) for timed operation
Fig. 702 Automatic Control Circuit with Control Unit 1572 and Timer (Triple Timer)
703
4
1
3 3 3 3 3 3
Wire colors
1 Diagnostic connector bl blue
br brown
3 Pin assignment: Pin assignment 4wire lead 7wire lead ge yellow
D1 0,75 gr 0,75 rt gn green
D2 0,75 or 0,75 or Wire gauges
gr gray
D3 0,75 gn 0,75 bl < 7.5 m 7.5 - 15 m or orange
D4 0,75 br 2,0 br 1.5 mm2
0.75 mm2 rt red
F1 nicht belegt 2,0 sw 1.0 mm2 1.5 mm2
F2 nicht belegt 2,0 rt/ws sw black
1.5 mm2 2.5 mm2
vi violet
2.5 mm2 4.0 mm2
4 with connection to terminal 61 auxiliary 4.0 mm2 6.0 mm2
ws white

A1 Heater S4 Switch power save operation
A2 Control unit SG 1572D U1 Igniter box
B1 Flame sensor observe polarity U2 Igniter electrodes
B2 Temperature sensor polarity optional W1 Wiring harness (1)
B3 Temperature limiter W2 Wiring harness (2)
B4 Thermostat for nozzle preheating A Plug connections, 6-pole
B5 Thermostat alternative to B3 C Plug connections, 1-pole
B6 Thermostat for vertical installation (MV Y1) D Plug connections, 4-pole
E1 Heating cartridge for nozzle preheating F Plug connections, 2-pole
F1 Fuse 5 A flat fuse DIN 72581 part 3 X1 Plug connections, 6-pole
H1 Light operation indicator light Y1 Solenoid valve
H2 Light flame indicator
S1 Switch on / off
S3 Switch external trigger circulation pump
Fig. 703 Automatic Control Circuit with Control Unit 1572D and Switch
704
4
1
2 3 3 3 3 3 3
1 Diagnostic connector
Wire colors
2 Timer P:
bl blue
with plus to connection 10 = continuous operating during immediate heating
terminal 10 not connected = duration of heating programmable (10 min to 120 min); br brown
ge yellow
3 Pin assignment: Pin assignment 4wire lead 7wire lead gn green
Wire gauges
D1 0.75 gr 0.75 rt gr gray
D2 0.75 or 0.75 or < 7.5 m 7.5 - 15 m or orange
D3 0.75 gn 0.75 bl 0.75 mm2 1.5 mm2 rt red
D4 0.75 br 2.0 br 1.0 mm2 1.5 mm2 sw black
F1 not used 2.0 sw 1.5 mm2 2.5 mm2
vi violet
F2 not used 2.0 rt/ws 2.5 mm2 4.0 mm2
4.0 mm2 6.0 mm2
ws white
4 with connection to terminal 61 auxiliary

A1 Heater P Standard timer (1531) for timed operation
A2 Control unit SG 1572D S3 Switch external trigger circulation pump
B1 Flame sensor observe polarity S4 Switch power save operation
B2 Temperature sensor polarity optional U1 Igniter box
B4 Thermostat for nozzle preheating W1 Wiring harness (1)
B5 Thermostat alternative to B3 W2 Wiring harness (2)
B6 Thermostat for vertical installation (MV Y1) A Plug connections, 6-pole
F1 Fuse 5 A flat fuse DIN 72581 part 3 D Plug connections, 4-pole
F2 Fuse 25 A flat fuse DIN 72581 part 3 F Plug connections, 2-pole
H2 Light flame indicator X3 Plug connections, 8-pole
H4 Symbol for Heating symbol lighting (in item P) X4 Plug connections, 12-pole
in Display
Y1 Solenoid valve
Fig. 704 Automatic Control Circuit with Control Unit 1572D and Standard Timer
705
61 61 A
6 1
30 30
DEUTSCH
5 2
F1 F2 F3 4 3
F
S4 1 2
S3 X3 1 1
Signal UP UPFA SP FA K BA
D
D+
6 5 7 3 1 2 4
6
rt/sw
sw
sw
br
or
rt
bl
7 1
2
3
4
W1 C
X1 F D C
A 1 2 3 2 1 4
1
3
S1 1 sw 5 2 1
3 rt/ws 3
4 rt 4
X1
sw 2
2 br 6
X3
5
M1 U1 B3/B5 B2
X2
2 br H1 H2
B4
+ SE -
M2 M U1 M B3
1 sw E1 M1
Y1 B2 B1
A2 B1 Y1 E1 A1 U2
X2 A2 A1
31 31
Wire colors
bl blue
br brown
ge yellow
Wire gauges
< 7,5 m 7,5 - 15 m gr gray
0,75 mm2 1,5 mm2 or orange
1,0 mm2 1,5 mm2 rt red
1,5 mm2 2,5 mm2 sw black
2,0 mm2 ? mm2 vi violet
2,5 mm2 4,0 mm2
ws white
4,0 mm2 6,0 mm2

A1 Heater not grounded U2 Igniter electrodes
A2 Control unit SG 1572D W1 Wiring harness (1+2)
B1 Flame sensor observe polarity A Plug connections, 6-pole
B2 Temperature sensor polarity optional C Plug connections, 1-pole
B3 Temperature limiter D Plug connections, 4-pole
B4 Thermostat for nozzle preheating F Plug connections, 2-pole
E1 Heating cartridge for nozzle preheating X1 Plug connections, 7-pole
F3 Fuse 5 A flat fuse DIN 72581 part 3
H1 Light operation indicator light
H2 Light flame indicator
S1 Switch on / off
S3 Switch external trigger circulation pump
U1 Igniter box
Fig. 705 System Circuit Daimler Chrysler Citaro, Ident.-Nr. 67131
706
30 30 A
6 1
DEUTSCH
F3 F2 5 2
4 3
C
S2
S4 1
S1 9 8 6 5 D
gn
or
br
gr
S3 X1
1
2
3
A D 3 2 1 4
4
2 5
sw A
3 or 1
3
6 5 1 4 X1
2
1 rt/ws 9 8
3
10 7
A
K1
14
15 rt 4 16
13 12 15 11
7 br 6
10 sw 2 K2 1 X2
16
4
4 bl
M1 U1 F1/B3 B2 rt
2
C 3
B5
rt
W1 B4
H1 - H2
3 br + SE
B3
U1 M
E1 M1
M2 M
Y1 B2 B1
A2 B1 Y1 E1 A1 1 sw U2
A2 A1
X2
-31 -31
Fuse acc. to SAE J 1284 / DIN 72581 Wire colors

DW 230 DW 300 DW 350
25A / 16A 25A / 16A 25A / 16A
bl blue
25A / 16A 25A / 16A 25A / 16A br brown
ge yellow
1 Diagnostic connector Wire gauges gn green
< 7,5 m 7,5 - 15 m gr gray
2,5 mm2 4,0 mm2
ws white
4,0 mm2 6,0 mm2

A1 Heater not grounded S3 Switch, external trigger required, if S2 not installed
circulation pump
A2 Control unit SG 1572
B3 Temperature limiter alternative to F1 U2 Igniter electrodes
B4 Thermostat for nozzle preheating W1 Wiring harness Van Hool
B5 Fire sensor Van Hool A Plug connections, 6-pole
E1 Heating cartridge C Plug connections, 1-pole
F2 Fuse see table D Plug connections, 4-pole
F3 Fuse see table X1 Plug connections, 16-pole
H2 Light flame indicator Y1 Solenoid valve
K1 Relay (in item A2) for circulation pump motor
K2 Relay (in item A2) for combustion air fan
S1 Switch on / off
Fig. 706 System Circuit Van Hool, Ident.-Nr. 89401
707
30 30 A
6 1
DEUTSCH
F3 F2 2
5
4 3
C
S2
S4
1
S1 X3 4 3 2 1
D
gn
or
br
gr
S3 W2
X1 W1 A D 3 2 1 4
1
2
3
1 sw 5 4
5 or 1 X1
rt/ws 1 2 3
3 3
4 5 6
K1 X2
1
4 rt 4
2
2 br 6
K2 X3
6 bl 2 1 3 5 7
M1 U1 F1/B3 B2
1 br
B4
H1 M2 M + SE - H2
2
sw C U1 M F1
E1 M1
Y1 B2 B1 2 4 6 8
X2 U2
A2 B1 Y1 E1 A1 A2 B3
A1
-31 -31
Fuse acc. to SAE J 1284 / DIN 72581 Wire colors

DW 230 DW 300 DW 350
25A / 16A 25A / 16A 25A / 16A
bl blue
25A / 16A 25A / 16A 25A / 16A br brown
ge yellow
1 Diagnostic connector Wire gauges gn green
< 7,5 m 7,5 - 15 m gr gray
2,5 mm2 4,0 mm2
ws white
4,0 mm2 6,0 mm2

circulation pump
A2 Control unit SG 1572D
B3 Temperature limiter alternative to F1 U2 Igniter electrodes
E1 Heating cartridge for nozzle preheating W2 Wiring harness (2)
F2 Fuse see table A Plug connections, 6-pole
F3 Fuse see table C Plug connections, 1-pole
H1 Light operation indicator light D Plug connections, 4-pole
K1 Relay for circulation pump motor X2 Plug connections, 2-pole
K2 Relay for combustion air fan X3 Plug connections, 8-pole
M1 Motor combustion air fan Y1 Solenoid valve
S1 Switch on / off
Fig. 707 System Circuit O405 / O407 / O408, Ident.-Nr. 91292
708
61 61 A
6 1
30 30
DEUTSCH
5 2
4 3
F1 F2
C
S2
S4 1 1
D+
D
L SP FA K M
S1 X2 1 5 4 3 2 1 X3
rt/sw
sw
br
or
bl
rt
1
2
S3 W2 3
4
D
X1 W1 A F 2 1 3 2 1 4 F
1 sw 5
1 2
3
5 or 1 2 1
X1
3 rt/ws 3
8
3
4 rt 4
2
4
1
7 2 5
7
7
2 br 6
X2
6 bl
M1 U1 B3/B5 B2
C
A
1
X3
B4
H1 + SE - H2
U1 M B3
M
M2 E1
A2 B1 Y1 E1 A1 sw 2
M1 Y1 B2 B1
U2
A2 A1 A 1
31 31 5
2
4
Wire colors
bl blue
br brown
ge yellow
Wire gauges
< 7,5 m 7,5 - 15 m gr gray
2,5 mm2 4,0 mm2
ws white
4,0 mm2 6,0 mm2

A1 Heater not grounded U1 Igniter box
A2 Control unit SG 1572D U2 Igniter electrodes
B1 Flame sensor observe polarity W1 Wiring harness (1)
B2 Temperature sensor polarity optional W2 Wiring harness (2)
B3 Temperature limiter A Plug connections, 6-pole
B4 Thermostat for nozzle preheating C Plug connections, 1-pole
E1 Heating cartridge for nozzle preheating D Plug connections, 4-pole
M1 Motor combustion air fan Y1 Solenoid valve
S1 Switch on / off
S3 Switch, external trigger required, if S2 not installed
circulation pump
Fig. 708 System Circuit MAN, Ident.-Nr. 89404
709
1 1
Wire colors
bl blue
br brown
ge yellow
Wire gauges
< 7,5 m 7,5 - 15 m gr gray
2,5 mm2 4,0 mm2
ws white
4,0 mm2 6,0 mm2
Item Nomenclature Remark Pos. Nomenclature Remark

circulation pump
A2 Control unit SG 1572D
B5 Temperature sensor extern observe polarity W2 Wiring harness (2)
B6 Thermostat alternative to B3 A Plug connections, 6-pole
F1 Fuse 25 A flat fuse DIN 72581 part 3 D Plug connections, 4-pole
M1 Motor combustion air fan X4 Plug connections, 4-pole
M2 Motor circulation pump X5 Plug connections, 4-pole
S1 Switch on / off Y1 Solenoid valve
S2 Continuity switch on water cock Y2 Shut-off valve with filter
Fig. 709 System Circuit SETRA, Ident.-Nr. 90972
710
1 Diagnostic connector
Wire colors
2 Timer P: bl blue
with plus to connection 4 = continuous operating during immediate heating
without plus to connection 4 = heating period 1 hour br brown
ge yellow
3 Pin assignment: Pin assignment 4wire lead 7wire lead gn green
D1 0,75 gr 0,75 rt Wire gauges
gr gray
D2 0,75 or 0,75 or
D3 0,75 gn 0,75 bl < 7,5 m 7,5 - 15 m or orange
D4 0,75 br 2,0 br 0,75 mm2 1,5 mm2 rt red
F1 not used 2,0 sw 1,0 mm2 1,5 mm2 sw black
F2 not used 2,0 rt/ws 1,5 mm2 2,5 mm2
vi violet
2,5 mm2 4,0 mm2
4 Option 4,0 mm2 6,0 mm2
ws white

A1 Heater P Digital timer, standard (1531) For programmed operation
A2 Control Unit SG 1572 D S1 Switch on / off
B1 Flame Sensor observe polarity S3 Switch external trigger circulation pump
B2 Temperature sensor polarity optional S4 Switch power save operation
B3 Temperature limiter S5 Switch Auxiliary heating mode
B4 Thermostat for nozzle preheating S6 Switch Filter heater on
B5 Thermostat alternative to B3 T Temperature switch Filter heater
B6 Thermostat for vertical installation (MV Y1) U1 Igniter box
E Filter heater U2 Igniter electrodes
E1 Heating cartridge for nozzle preheating W1 Wiring harness (1)
F1 Fuse 5A flat fuse DIN 72581 part 3 W2 Wiring harness (2)
F2 Fuse 25A flat fuse DIN 72581 part 3 W3 Wiring harness (3
F3 Fuse 25A flat fuse DIN 72581 part 3 A Plug connections, 6-pole
F4 Fuse 25A flat fuse DIN 72581 part 3 C Plug connections, 1-pole
F5 Fuse 5A flat fuse DIN 72581 part 3 D Plug connections, 4-pole
F6 Fuse 5A flat fuse DIN 72581 part 3 F Plug connections, 2-pole
F7 Fuse 5A flat fuse DIN 72581 part 3 O Plug connections, 2-pole
H1 Light operation indicator light Q Plug connections, 2-pole
H4 Heating symbol on the display Power-on indicator (in item P) X2 Plug connections, 2-pole
K4 Relay X3 Plug connections, 7-pole
M1 Motor combustion air fan X4 Plug connections, 12-pole
M2 Motor circulation pump X5 Plug connections, 4-pole
Y1 Solenoid valve
Fig. 710 Automatic Control Circuit Rail with Control Unit 1572D and Standard Timer and filter heater
711
712
Thermo 230 / 231 / 300 / 301 / 350 8 Servicing
8. Servicing plished twice per heating season.

in case of leakage the fuel pump and the fuel lines
must be replaced immediately, otherwise every 5
8.1 General years.
the heater should be checked in regular intervals by a
This section describes the servicing procedures allowed Spheros service agent, the latest before the beginning
on the heater when installed. of the heating season (refer to Annex A "Scheduled
Maintenance").When the heater is operated in rail ve-
hicles, mainte-nance chart / test certificate item
no. 90 087 22B is to be used.
8.2 Heater Servicing
8.5.1 Inspection and Attachment of the Exhaust
As long as the heater is in operation or in run-down the
Muffler (only heaters from year of
battery main power supply must not be disconnected to
prevent the heater from overheating by response of the
production 1996 and up to production
overheat protection. date 1996, calendar week 36; 3G......)
When performing long time repairs on the heater its
removal is appropriate. NOTE
After working on the heating circuit replenish with a If the exhaust muffler is already secured with a sheet
coolant mix prepared with water and anti-freeze and metal screw, the following procedure need not be per-
bleed circuit afterwards according to manufacturers formed.
instructions.
General
The exhaust muffler of heaters manufactured from the

8.3 Vehicle Servicing beginning of 1996 up to a manufacturing date of 1998
(calendar week 36; 3G.......) (for year or date of production
CAUTION refer to identification label) the exhaust muffler may get
In the vicinity of the heater a temperature of 110 C must loose or lost under certain circumstances. Therefore an
under no circumstances be exceeded (e.g. during paint inspection for proper attachment of the muffler should be
work on the vehicle). performed.
Heaters manufactured
8.4 Heater Test Run from beginning of 1996
Identification up to 1998, calendar
The heater must not be operated, not even with the timer, label week 36; 3G......)
in enclosed areas like garages or workshops not equipped
with exhaust ventilation facilities.
8.5 Maintenance
To ensure functional reliability of the heater the following

maintenance must be performed:
check combustion air inlet and exhaust outlet for

contamination and clean as required.
outside the heating season the heater should be
operated with the vehicle engine cold approximately
every four weeks for 10 minutes setting the heating
system to "warm". This avoids difficulties in the
start-up.
at least once a year, in case of contaminated fuel
more often, the fuel filter or filter cartridge as well as
the filter screen of the fuel pump must be replaced to
avoid malfunctions.
at least once a year the heat exchanger must be Exhaust muffler
cleaned inside.
Valid for application 350.190:
The cleaning of the heat exchanger is to be accom-
801
8 Servicing Thermo 230 / 231 / 300 / 301 / 350
Inspection and Attachment 3. If no muffler is found in exhaust end pipe check if

muffler is upstream in exhaust pipe. If muffler is
NOTE dislocated in the exhaust pipe, arrest muffler as
The exhaust muffler must always be secured with a sheet described in NOTE. Slot or drill exhaust pipe and refit.
metal screw. Drill a hole with a diameter of 2.5 mm into 4. If the exhaust muffler has been lost it may be ordered
the exhaust end pipe and muffler and arrest muffler with a from Spheros (ident. no. 206 91D). Fasten muffler
sheet metal screw B 3.9 x 25 (see figure). according to NOTE. Slot or drill exhaust pipe and refit.
5. If heater is operated without exhaust pipe, fasten
1. Check exhaust end pipe for presence of muffler. muffler according to NOTE. An exhaust deflector
For checking remove exhaust end pipe as required. (ident. no. 849 70A) must be additionally fitted.
2. If muffler is found in exhaust end pipe fasten as
described in NOTE. Slot or drill exhaust end pipe and
refit.
Exhaust end pipe
Exhaust Sheet metal Sheet metal screw

end pipe screw B 3.9 x 25
B 3.9 x 25
Hole Hole
2.5 mm 2.5 mm
Exhaust muffler
(ident. no. 206 91D) Exhaust muffler
(ident. no. 206 91D)
Slot exhaust
pipe
Exhaust deflector
(ident. no. 849 70A)
Heater without exhaust pipe

Exhaust pipe
Heater with exhaust pipe
802
8.5.2 Burner Head Opening and Closing Opening or removal

or Removal and Installation 1. Disconnect electrical connections to temperature
limiter and temperature sensor.
WARNING 2. Loosen nuts (3, Fig. 801) enough to release hinge
The igniter box operates with high voltage. Prior to bolts (2).
opening the burner head the connectors of the cable 3. Swing hinge bolts (2) out.
harness in the vehicle have to be disconnected to prevent 4. Swing burner head (4) open.
lethal injuries. 5. Remove cotter pin (1) as required to remove burner
After closing and fixing burner head, reconnect connec- head.
tors in the vehicle.
Closing or installation
NOTE 1. As required fasten burner head (4, Fig. 801) in
Maintenance on the heater is easy. By swinging the position using cotter pin (1).
burner head open the following components become 2. Swing burner head (4) closed and locate for
accessible: assembly.
fuel pump and fuel nozzle 3. Swing hinge bolts (2) into lock position and secure
solenoid valve with nuts (3).
igniter box 4. Torque nuts (3) with 7.5 Nm + 1 Nm.
igniter electrodes 5. Reconnect electrical connections to the temperature
flame sensor limiter and temperature sensor.
combustion chamber
nozzle block preheater (if installed) NOTE
When making electrical connections observe wiring color
In order to obtain a convenient burner head opening angle codes.
it is required to disconnect the electrical connection(s) to
the temperature limiter and temperature sensor.
1 Cotter pin
2 Screw (2)
3 Nut (2)
4 Burner head
NOTE
4 Depending on the burner head direction of swing the
cotter pin may be located on the opposite side.
Fig. 801 Swinging Burner Head open
803
8.6 Visual Inspections and Regulations 8.6.2 Connection to Vehicle Fuel System
for Installation
Fuel is tapped from the fuel reservoir of the vehicle or from
a separate fuel tank.
8.6.1 Connection to Vehicle Cooling System
8.6.2.1 Fuel Lines
The installation of the heater should be in a location as low
as possible to ensure self-venting of the heater and circu-
In order to avoid air from being captured in fuel lines, they
lation pump. This applies in particular for the circulation
should only be installed with an incline. The fuel line joints
pump because it is not self-sucking.
are to be secured against slipping with hose clamps
should no screwed mechanical unions be in use.
The heater is to be connected to the vehicle cooling
system according to Fig. 802. The cooling system coolant
Should fuel hoses be installed always use the hoses
capacity must be at least 10 liters.
supplied or offered by Spheros. If other hoses are used
they must at least meet the specifications of DIN 73379.
The vehicle cooling system or the separate heating circuit
Fuel hoses must not be kinked or twisted and must be
must use only pressure relief valves with an opening
secured with clamps every 25 cm.
pressure of at least 0.4 bar and of max. 2.0 bar.
For routing fuel also fuel lines may be used consisting of
It is a basic requirement to use the coolant hoses supplied
materials standard in the manufacturing of vehicles, e.g.
by Spheros, otherwise the hoses must at least meet the
steel, copper or plastic lines made of unhardened, light
specifications of DIN 73411. The hoses have to be instal-
and temperature stabilized PA11 or PA12 (e.g. Mecanyl
led free of kinks and for proper venting in an inclination.
RWTL) according to DIN 73378 observing the applicable
Hose connections must be secured against slippage with
jointing instructions.
hose clamps.
Basic rules for the routing of fuel lines are:
NOTE
Protect against undue temperatures.
The specified tightening torques of the hose clamps used
must be complied with.
WARNING
In overheat condition the heater outer shell may reach
Prior to the heaters first operation or after replacement of
Diesel fuel inflammation temperature!
the coolant, attention must be paid to carefully bleed the
cooling system. Heater and lines must be installed so that
Protect lines from stone strike.
static venting is guaranteed.
Dripping or evaporating fuel may neither accumu-
late nor ignite on hot components or electrical
Improper venting may cause malfunctions by overheating
equipment.
in equipment operation.
Proper venting may be identified by a circulation pump

almost noiseless in operation.
When using the circulation pump Aquavent 6000 (U4851)

or Aquavent 6000S (U4852) or Aquavent 6000SC
(U4856) the circulation pump automatically is switched off
approx. 15 seconds after switch-on if coolant is lacking or
the pump wheel is jammed.
In combination with control unit 1572D (Thermo label

colored) and with programmed circulation pump check the
heater also switches off when coolant is missing.
804
Water heating circuit

Sidewall radiators and roof duct heating
6
3 4 7
1
1
1
2
9
8 Vorlauf
Supply
Rcklauf
Return
1 Sidewall radiator with fan

2 Heat exchanger, entrance
3 Heater unit
4 Circulation pump
5 Heat exchanger, roof
6 Vehicle engine
7 Cockpit heating
8 Control element
Fig. 802 Example of a Heater Installation in a Passenger Bus
805
When installing a shut-off device in the return line a clearly It must be located so that no clogging by contamination,
visible information label must be provided. impact of snow, or intake of splash water is to be
expected.
CAUTION
Operation with the return line shut off causes damage to The combustion air intake and exhaust outlet is to be
the fuel pump. Fuel may escape. Danger of fire. located so that no air pressure difference builds up in any
operating condition of the vehicle.
Permissible dimensions of combustion air intake line:

inner diameter: 55 mm
max. length: 5 m without the exhaust extension
max. bend: 270
The combustion air inlet must be located so that no

exhaust fumes can enter.
NOTE
If the combustion air intake line cannot be routed upwards
to the heater, a water drain hole 4 mm is to be provided
at the lowest point.
If the heater is located near the fuel tank in a common

installation compartment, combustion air must be taken
in from and the exhaust routed to the exterior. The
Information label feedthroughs must be sealed against splash water.
Loose fuel lines must be secured in order to avoid If the heater is located in a closed installation box, a vent
sagging. port is required:
The installation of an additional fuel pump is not allowed. Thermo 230, 231, 300 and 301 30 cm2
Thermo 350 35 cm2
Fuel lines permissible dimensions:
inner diameter for suction and return line: If the temperature in the installation box exceeds the
6 mm (other diameters upon request). permitted ambient temperature of the heater (see
max. permissible length for each suction and return Technical Data), the vent port must be enlarged consult-
line: 10 m ing Spheros.
Max. permissible suction height: 2 m
Max. permissible priming pressure: 0.3 bar for suction
and return line. 8.6.4 Exhaust Line
8.6.2.2 Fuel Filter CAUTION

Observe official regulations concerning the installation
A fuel filter supplied as deliverable item or cleared for use (see 1.6).
by Spheros is to be fitted.
Installation position possibly vertical with horizontal The exhaust pipe outlet opening must not point in the
direction of flow. To avoid operating malfunctions replace direction of motion.
filter or filter cartridge once a year or more often if fuel is
contaminated. The exhaust pipe outlet opening must be located so as not
to expect clogging by snow or mud.
8.6.3 Combustion Air Supply The combustion air intake and exhaust outlet is to be
located so that no air pressure difference builds up in any
CAUTION operating condition of the vehicle.
Observe official regulations concerning the installation
(see 1.6).
Combustion air must under no circumstances be

extracted from rooms with persons. The combustion air
inlet must not point towards the forward direction of
motion.
806
Rigid pipes made of unalloyed or alloyed steel with a 5. Secure combustion air inlet line on heater as
minimum wall thickness of 1.0 mm have to be used as applicable.
exhaust line or flexible pipes made of alloyed steel only. 6. Connect electrical connectors of cable harness in
The exhaust pipe is secured to the air heater e.g. with a vehicle and to circulation pump.
clamp. 7. Bleed fuel supply system.
8. Bleed coolant circuit.
Permissible exhaust line dimensions:
inner diameter: 70 mm
max. length: 5 m without the exhaust extension 8.7.2 Temperature Limiter, Replacement
max. bend: 270
NOTE
As an alternative an exhaust deflector must be installed The replacement procedure for the temperature limiter is
cleared by Spheros. identical with the heater installed or removed.
Perform replacement in accordance with 9.2.1.
8.7 Removal and Installation

8.7.3 Temperature Sensor, Replacement
CAUTION
In installed condition only the following disassembly or NOTE
removal procedures are permitted should enough space The replacement procedure for the temperature sensor is
for removal allow such action: identical with the heater installed or removed.
replacement of temperature limiter
replacement of temperature sensor WARNING
replacement of combustion air fan Prior to replacement of temperature sensor in installed
replacement of burner condition relief overpressure in cooling system by opening
replacement of igniter box the cooling circuit sealing element.
replacement of flame sensor If required also allow heater to cool down and have
replacement of combustion chamber collector vessel ready to collect escaping coolant.
8.7.4 Burner, Replacement

8.7.1 Heater, Removal and Installation
NOTE
8.7.1.1 Removal The replacement procedure for the burner is identical with
the heater installed or removed.
1. Disconnect connectors of cable harness in vehicle Perform replacement in accordance with 9.2.3.
and of circulation pump.
2. Disconnect combustion air intake on heater if WARNING
required. The igniter box operates on high voltage. Prior to replace-
3. Loosen clamp on exhaust outlet. ment of burner disconnect electrical connectors of cable
4. Loosen fuel supply and return line connections and fit harness in vehicle to avoid lethal accidents.
dummy plugs.
Close water cocks as applicable.
5. Loosen hose clamps on coolant hoses, disconnect 8 7.5 Igniter Box, Replacement
hoses and fit dummy plugs.
6. Remove 3 screws and washers or 4 screws and NOTE
washers. The replacement procedure for the igniter box is identical
7. Remove heater. with the heater installed or removed.
8.7.1.2 Installation
WARNING
1. Locate heater for installation and secure with 3 screws The igniter box operates on high voltage. Prior to replace-
and washers or 4 screws and washers. ment of igniter box disconnect electrical connectors of
2. Secure line on exhaust outlet using clamp. cable harness in vehicle to avoid lethal accidents.
3. Slide on coolant hoses and fasten with hose clamps.
Torque clamps with 1.5 Nm. Open water cocks.
4. Connect fuel supply and return lines and tighten
connections or screw tight with banjo bolt and new
gaskets.
807
8.7.6 Flame Sensor, Replacement 8.8.1 Water Circuit, Bleeding
NOTE NOTE
The replacement procedure for the flame sensor is identi- Bleeding must always be performed in accordance with
cal with the heater installed or removed. manufacturers instructions. For bleeding the circulation
Perform replacement in accordance with 9.2.8. pump must not be switched on.
WARNING Set vehicle own heating system to "warm" and replenish

The igniter box operates on high voltage. Prior to re- coolant which must consist of at least 10 % anti-freeze
placement of flame sensor disconnect electrical connec- (on glycol base) (protection against corrosion). When
tors of cable harness in vehicle to avoid lethal accidents. using pure water there will be no protection against
corrosion and due to the lower boiling point of the water
8.7.7 Combustion Chamber, Replacement when overheating loss of cooling water may result
requiring continuous replenishment. Additives in the
NOTE coolant must not affect metals, plastics or rubber and
The replacement procedure for the combustion chamber leave no deposits.
is identical with the heater installed or removed.
Perform replacement in accordance with 9.2.10. Then operate engine at increased idle until radiator
thermostat opens. Shut down engine, check coolant level
WARNING and replenish as required.
The heater operates on high voltage. Prior to replacement
of combustion chamber disconnect electrical connectors Switch on heater and vehicle heating fan with engine shut
of cable harness in vehicle to avoid lethal accidents. down. After a certain cool-down period the heater must
automatically switch on and control to off. In case of no
restart attempt the temperature limiter on the heater has
8.8 First Operation responded because the heater has not been bled proper-
ly. Reset temperature limiter (push button on temperature
limiter) and repeat complete bleeding procedure.
After heater installation the coolant circuit and the fuel
supply system must be thoroughly bled observing the
NOTE
vehicle manufacturers instructions. During test runs all
The heater may be equipped with an automatically
coolant and fuel line connections have to be checked for
resetting temperature limiter. The manual reset is not
security and no leakage. Should the heater in operation
necessary.
enter a fault condition, perform troubleshooting (refer to
Section 5).
8.8.2 Fuel Supply System, Bleeding
NOTE
The whole fuel supply system including the fuel filter must
Heaters with control unit 1572D:
completely filled with fuel before initial start-up.
If the heater performs 5 subsequent attempts to start due
to a malfunction, the heater enters an error lockout and
stops any further attempts to start. This error lockout is
NOTE
superior to the normal error lockout condition.
Never use the fuel pump to fill / bleed the fuel system!
The error lockout reset is achieved by switching the heater
on and disconnection of the heater power supply within
120 sec. during run-down.
ATTENTION
In the event no fuel comes to the fuel pump during initial
start-up, there is a risk that the fuel pump will be damaged!
808
Thermo 230 / 231 / 300 / 301 / 350 9 Repair
9 Repair
9.1 General
This section describes the repairs that may be performed

on the heaters Thermo 230, 231, 300, 301 and 350 when
removed. Any further disassembly will void the warranty.
For re-assembly only components of the proper spare part
kits are to be used.
WARNING
The igniter box operates on high voltage. The following
components may also be replaced with the heater
installed unless restricted space prevents access:
temperature limiter
temperature sensor
combustion air fan
burner
igniter box
flame sensor
combustion chamber
Prior to replacement disconnect connectors of cable

harness in vehicle to avoid lethal accidents.
WARNING
Hot coolant may escape during the replacement of the
temperature sensor.
Before replacing the temperature sensor also release
pressure from cooling system by opening sealing
element.
If required also allow heater to cool down.
901
9 Repair Thermo 230 / 231 / 300 / 301 / 350
9.1.1 Work on Components after Disassembly 9.1.2 Incorporation of Modifications
CAUTION NOTE
All gaskets located between disassembled components Continuous enhancement of heater design is for optimi-
must always be replaced and discarded. zing performance and avoiding failures and malfunctions.
Normally equipment in use may be retrofitted using
9.1.1.1 Visual Inspection, General available modification kits
Examine all components for damages (cracks, The following modifications may be incorporated during
deformation, wear, etc.) and replace as necessary. repair procedures:
Examine connectors and wiring for corrosion, loose
contacts, wrong crimping, etc. and repair as installation of control unit 1572D as substitute for
necessary. control unit 1572 (see 9.1.2.1)
Check terminals for corrosion and contacts for
security. Repair as required.
9.1.1.2 Combustion Chamber, Visual Inspection
Check swirl ring for security.

Inspect combustion chamber for oxidizing and coke
deposits and remove as required.
Check welding seem for cracks.
NOTE
Longitudinal cracks up to 80 mm are allowed.
9.1.1.3 Heat Exchanger, Visual Inspection
Inspect exhaust ducting in heat exchanger for sooting,

deposits, damage and corrosion.
NOTE
Deposits are to be removed with water jet and brush.
Inspect heat exchanger for exterior damage, defor-

mation, etc.
NOTE
Heavy deformation may cause restricted flow of coolant.
CAUTION
When replacing the combustion chamber on
heaters installed vertically, remove deposits in heat
exchanger using a suitable tool.
9.1.1.4 Combustion Air Fan Wheel, Visual Inspection
Check fan wheel for contamination and cracks.

Check cover plate for security.
Check slide lock for proper sealing.
902
Thermo 230 / 231 / 300 / 301 / 350 9 Repair
9.1.2.1 Installation of Control Unit 1572D as Procedure

Substitute for Control Unit 1572
CAUTION
General Control unit 1572D may only be used in combination
with the igniter box delivered (green connector cover).
Due to the progress in the development of processors The electrical connector is coded.
control unit 1572 can no longer be supplied.
The retrofit of control unit 1572D is performed according 1. Remove control unit according to 9.2.5.1 and
to the following procedure: discard.
2. Remove igniter box according to 9.2.7.1 and
The modification kit consists of: discard.
control unit 1572D 3. Install new igniter box according to 9.2.7.2.
igniter box 4. Install new control unit according to 9.2.5.2.
thermo identification label 5. Apply new thermo label onto existing label to indicate
retrofit.
Previous igniter box

(black connector cover)
Thermo label
New igniter box

(green connector cover)
Control unit 1572
Control unit 1572D
903
9 Repair Thermo 230 / 231 / 300 / 301 / 350
9.2 Disassembly and Assembly 9.2.2.2 Installation
9.2.1 Temperature Limiter, Replacement 1. Manually screw temperature sensor (2, Fig. 901) into
coolant outlet (4).
2. Torque temperature sensor to 20 Nm +5 Nm.
9.2.1.1 Removal
3. Restore electrical connections.
1. Disconnect electrical connection to temperature
NOTE
limiter.
Observe electrical wiring color coding when making
2. Withdraw rubber cap. Using screw driver lever off
connections to temperature sensor.
retaining spring and remove temperature limiter
(1, Fig. 901).
9.2.1.2 Installation 9.2.3 Burner, Replacement
1. Slide rubber cap of temperature limiter (1, Fig. 901) 9.2.3.1 Removal
back until temperature limiter can be located for
installation. 1. Disconnect electrical connections on burner and
2. Position temperature limiter (1) in connector (3) and loosen fuel lines.
push in retaining clip. 2. Loosen nuts (6, Fig. 901) until hinge bolts are free.
3. Swing hinge bolts (7) open and remove cotter pin (5).
WARNING 4. Remove burner (8).
The retaining spring must be located in the groove of the 5. Perform procedures on components after
housing and must be latched in position both perceptibly disassembly (refer to 9.1.1).
and audibly (twice) at the collar of the locating socket.
Only then will the temperature limiter be in proper contact 9.2.3.2 Installation
with the heat exchanger jacket.
1. Position burner (8, Fig. 901) for installation, swing
3. Fit rubber cap. hinge bolts closed and secure temporarily using
After the rubber cap has been placed in position, the screws (6).
cable must be aligned in the cable sleeve, free from 2. Insert cotter pin (5) according to the intended opening
strain. swing direction.
Connection cables must not be routed over reset 3. Tighten nuts (6) with 7.5 Nm + 1 Nm.
button. 4. Connect fuel lines.
5. Restore electrical connections.
NOTE
connections to temperature limiter. NOTE
4. Make electrical connections. connections to temperature limiter and temperature
sensor.
9.2.2 Temperature Sensor, Replacement
9.2.2.1 Removal
1. Disconnect electrical connection to temperature

sensor.
WARNING
Prior to replacement of temperature sensor in installed
condition relief overpressure in cooling system by opening
the cooling circuit sealing element.
If required also allow heater to cool down and have
collector vessel ready to collect escaping coolant.
2. Unscrew temperature sensor (2, Fig. 901) and

remove.
904
Thermo 230 / 231 / 300 / 301 / 350 9 Repair
1 Temperature limiter Rubber cap

2 Temperature sensor Temperature
3 Connector limiter
4 Coolant outlet
5 Cotter pin
6 Nut (2) Retaining clip
7 Hinge bolt (2)
8 Burner
2
4
8 7 NOTE
Cotter pin (5) may be fitted on other side as required for
burner head to swing open in opposite direction.
Fig. 901 Temperature Limiter, Temperature Sensor and Burner, Replacement
905
9 Repair Thermo 230 / 231 / 300 / 301 / 350
9.2.4 Combustion Air Fan, Replacement 9.2.4.2 Installation
NOTE NOTE
For replacement of the combustion air fan the burner may Fan motor (7, Fig. 902) to be aligned with control unit
be left installed. (recess in mounting flange) and with clutch (by rotating
In removed condition ensure that igniter electrodes are drive shaft).
not bent and nozzle is not damaged.
1. Align fan motor (7) and position for installation.
9.2.4.1 Removal 2. Attach fan motor using screws (6) and lock washers.
3. Tighten screws with 5 Nm + 1 Nm.
1. Loosen screws (3, Fig. 902) and withdraw cap (2) 4. Connect electrical connector (9).
from burner. 5. Bring slide lock (5) on fan wheel in installation
2. Using suitable tool (e.g. mandrel 3 mm) open slide position.
lock (5) until fan wheel can be pulled off. 6. Slide fan wheel onto drive shaft and using suitable tool
3. Disconnect electrical connector (9). (e.g. mandrel 3 mm or pliers) close slide lock until fan
4. Remove screws (6) with lock washers and withdraw wheel is locked.
fan motor (7). 7. Locate cap (2) and secure with screws (3).
5. Perform procedures on components after 8. Tighten screws with 2 Nm.
disassembly (refer to 9.1.1).
Opening slide lock Closing slide lock
906
Thermo 230 / 231 / 300 / 301 / 350 9 Repair
5 6
4
8
9
7
1
1 Splash protection cover

2 Cap
3 Screw (2)
4 Fan wheel
3 5 Slide lock
6 Screw (3)
7 Fan motor
8 Clutch
9 Electrical connector
Fig. 902 Combustion Air Fan, Replacement
907
9 Repair Thermo 230 / 231 / 300 / 301 / 350
9.2.5 Control Unit, Replacement 9.2.6.2 Installation
NOTE 1. Install solenoid valve (7, Fig. 903) on fuel pump (10)
For replacement of the control unit the burner head if required.
may be left installed and must only be swung open for 2. Fit new O-ring (12) and filter screen (11) on fuel pump
disconnection of electrical connector (8, Fig. 903). (10).
In removed condition ensure that igniter electrodes are 3. Position fuel pump (10) for installation and secure
not bent and nozzle is not damaged. with screws (9) and lock washers.
If a control unit 1572 is substituted with a control unit 4. Tighten screws with 5 Nm + 1 Nm.
1572D, perform procedure according to 9.1.2.1. 5. Connect electrical connector (8).
6. Plug on disk (6) and mount heating cartridge.
7. Plug on igniter electrodes (3, Fig. 904).
9.2.5.1 Removal 8. Install burner (refer to 9.2.3.2).
1. Disconnect all electrical connections from control unit

(23, Fig. 903). 9.2.7 High Pressure Nozzle, Replacement
2. Swing burner head open (refer to 8.5.1) and
disconnect electrical connector (8). 9.2.7.1 Removal
3. Remove flame sensor (refer to 9.2.8.1).
4. Remove combustion air fan (refer to 9.2.4.1). 1. Remove burner (refer to 9.2.3.1).
5. Carefully withdraw control unit (23) in axial direction 2. Using screwdriver lever off igniter electrodes
from burner head (17) and remove. (3, Fig. 903) from igniter box (1) and remove.
6. Perform procedures on components after 3. Remove disk (6, Fig. 903) with heating cartridge
disassembly (refer to 9.1.1). (if installed).
4. Disconnect electrical connector (8) of the heating
cartridge.
9.2.5.2 Installation 5. Unscrew high pressure nozzle (4).
1. Carefully push control unit (23, Fig. 903) in axial

direction against stop into burner head (17). NOTE
2. Install combustion air fan (refer to 9.2.4.2). Ensure cleanliness is maintained when installing the
3. Make all electrical connections on control unit (23). nozzle. Only touch the nozzle at its hexagon surface.
4. Install flame sensor (refer to 9.2.8.2).
5. Connect electrical connector (8).
9.2.6 Fuel Pump, Replacement 1. Screw in high pressure nozzle (4, Fig. 903) and
tighten with 20 Nm.
9.2.6.1 Removal 2. Connect electrical connector (8) of the heating
cartridge.
1. Remove burner (refer to 9.2.3.1). 3. Plug on disk (6) and mount heating cartridge.
2. Using screwdriver lever off igniter electrodes 4. Plug on igniter electrodes (3, Fig. 903).
(3, Fig. 903) from igniter box (1) and remove. 5. Install burner (refer to 9.2.3.2).
3. Remove disk (6, Fig. 903) with heating cartridge
(if installed).
4. Disconnect electrical connector (8).
NOTE
During the following step ensure that escaping fuel is
immediately neutralized and properly disposed of.
5. Remove screws (9) with lock washers.

6. Withdraw fuel pump (10) together with solenoid valve
(7) and remove.
7. Remove and discard O-rings (12) and filter screen
(11).
8. Remove solenoid valve (7) from fuel pump (10) as
required.
9. Perform procedures on components after
908
Thermo 230 / 231 / 300 / 301 / 350 9 Repair
Igniter box 1
23 Overheat thermo-
stat (Thermo 231 /
mechanically coded)
301 only)
in combination with
control unit 1572D and
Control unit 26
also control unit
1572D
1572
5
2 6
3 7
1 4
8
9
Igniter box
(black connector
cover) only in
combination with
control unit 1572 5
6
25
10
11
12 24
13
Control unit
1572 14
15
16
17
18
23
1 Igniter box 15 Flame sensor
19 2 Screw (2) 16 Screw
3 Igniter electrodes 17 Burner housing
22 4 High pressure nozzle 18 Strain relief clamp (2)
20
21 5 Viewing glass 19 Screw (2)
6 Disk 20 Base plate for relays
7 Solenoid valve 21 Relay
8 Electrical connector 22 Relay
9 Screw (3) 23 Control unit
10 Fuel pump 24 Heating cartridge with
11 Filter screen thermostat
12 O-ring (2) 25 Clip
13 Rotating ring 26 Overheat thermostat
14 Screw 26 (Thermo Top 231 / 301 only)
Fig. 903 Control Unit and Fuel Pump, Replacement
909
9 Repair Thermo 230 / 231 / 300 / 301 / 350
9.2.8 Igniter Box, Replacement 9.2.9 Flame Sensor, Replacement
9.2.8.1 Removal 9.2.9.1 Removal
1. Remove burner if required (refer to 9.2.3.1). 1. Remove burner if required (refer to 9.2.3.1).
2. Using screw driver lever off igniter electrodes 2. If required lever off igniter electrodes (Fig. 904) from
(Fig. 904) from igniter box and remove. igniter box using screw driver and remove.
3. Remove disk (6). 3. Remove disk (6).
4. Remove screws (2) with lock washers. 4. Remove screw (14) and lock washer.
5. Withdraw igniter box (1) and remove. 5. Withdraw flame sensor (15) and remove.
6. Perform procedures on components after 6. Perform procedures on components after
disassembly (refer to 9.1.1). disassembly (refer to 9.1.1).
9.2.8.2 Installation 9.2.9.2 Installation
1. Locate igniter box (1, Fig. 904) for installation, plug on 1. Position flame sensor (15, Fig. 904) for installation,
making correct electrical connections and secure with plug on to make correct electrical connections and
screws (2) and lock washers. secure with screw (14) and lock washer.
2. Tighten screws (2) with 5 Nm + 1 Nm. 2. Tighten screw (14) with 5 Nm + 1 Nm.
3. Plug on disk (6) and align. 3. Plug on disk (6) and align.
4. Plug on igniter electrodes (3). 4. Plug on igniter electrodes (3).
5. Install burner (refer to 9.2.3.2). 5. Install burner (refer to 9.2.3.2).
Igniter box
Igniter electrodes
Removal and
installation of
igniter electrodes
Flame sensor
Fig. 904 Igniter Box and Flame Sensor, Replacement (Sheet 1 of 2)
910
Thermo 230 / 231 / 300 / 301 / 350 9 Repair
Igniter box 1
23 Overheat thermo-
stat (Thermo 231 /
mechanically coded)
301 only)
in combination with
control unit 1572D and
Control unit 26
also control unit
1572D
1572
5
2 6
3 7
1 4
8
9
Igniter box
(black connector
cover) only in
combination with
control unit 1572 5
6
25
10
11
12 24
13
Control unit
1572 14
15
16
17
18
23
1 Igniter box 15 Flame sensor
19 2 Screw (2) 16 Screw
3 Igniter electrodes 17 Burner housing
22 4 High pressure nozzle 18 Strain relief clamp (2)
20
21 5 Viewing glass 19 Screw (2)
6 Disk 20 Base plate for relays
7 Solenoid valve 21 Relay
8 Electrical connector 22 Relay
9 Screw (3) 23 Control unit
10 Fuel pump 24 Heating cartridge with
11 Filter screen thermostat
12 O-ring (2) 25 Clip
13 Rotating ring 26 Overheat thermostat
14 Screw 26 (Thermo Top 231 / 301 only)
Fig. 904 Igniter Box and Flame Sensor, Replacement (Sheet 2 of 2)
911
9 Repair Thermo 230 / 231 / 300 / 301 / 350
9.2.10 Heat Exchanger, Replacement 9.2.11 Combustion Chamber, Replacement
9.2.10.1 Removal 9.2.11.1 Removal
1. Remove temperature limiter (refer to 9.2.1.1). 1. Disconnect electrical connections to temperature

2. Remove temperature sensor (refer to 9.2.2.1). limiter and temperature sensor.
3. Remove burner (refer to 9.2.3.1). 2. Swing burner open (refer to 8.5.2).
4. Withdraw combustion chamber (1, Fig. 905) from heat 3. Withdraw combustion chamber (1, Fig. 905) from heat
exchanger (2). exchanger (2) and remove.
5. Remove heat exchanger (2). 4. Perform procedures on components after
6. Perform procedures on components after disassembly (refer to 9.1.1).
9.2.10.2 Installation 1. Slide combustion chamber (1, Fig. 905) fully into heat
exchanger (2) against stop.
1. Slide combustion chamber (1, Fig. 905) fully into heat 2. Swing burner closed (refer to 8.5.2).
exchanger (2) against stop.
2. Install burner (refer to 9.2.3.2). NOTE
3. Install temperature limiter (refer to 9.2.1.2). Observe electrical wiring color coding when making
4. Install temperature sensor (refer to 9.2.2.2). connections.
3. Make electrical connections to temperature limiter and

to temperature sensor.
1 Combustion chamber
2 Heat exchanger
1
Fig. 905 Heat Exchanger and Combustion Chamber, Replacement
912
Thermo 230 / 231 / 300 / 301 / 350 10 Packaging / Storage / Shipping
10 Packaging, Storage and

Shipping
10.1 General
The heater or its components shipped to Spheros for

testing or repair must be cleaned and packaged so that
they are protected against damage during handling, ship-
ping and storage.
CAUTION
When shipping a complete heater assembly it must be
drained completely. No coolant is allowed to escape when
packaging or shipping.
Dummy plugs must be fitted to the coolant inlet and outlet

as well as to the fuel lines.
In storage the ambient temperatures specified in

Section 4 must not be exceeded.
1001
10 Packaging / Storage / Shipping Thermo 230 / 231 / 300 / 301 / 350
Page empty for notes
1002
Thermo 230 / 231 / 300 / 301 / 350 Annex A
Annex A
Scheduled Maintenance
A-1
Annex A Thermo 230 / 231 / 300 / 301 / 350
Heater, Scheduled Maintenance * The maintenance intervals indicated below apply to appli-
cations and requirements typical of busses. Should the
The heater should be checked in regular intervals at least heaters be used in other vehicles or applications, these in-
at the beginning of the heating season (point of time when tervals may have to be adapted, i.e. shortened or exten-
weather conditions cause increased use of heater). ded.
In these cases, please contact your Spheros partner
charge.
Check / Maintenance Important Notes Check Result Measured Values,

Maintenance / Repair
i.O. nicht performed
i.O.
1. Electrical connections Use suitable contact

a) Disconnect electrical connectors to cable harness, spray, e.g. special
inspect for oxidation, spray and reconnect after performing contact spray
step 5. (order no. 101322).
b) Inspect fuses for oxidation and/or check transitionresistances.
2. Heat exchanger If necessary investigate

a) Inspect paint for dark stains of burn (local overheating). reason for overheating
(e.g. water circuit).
b) Check for signs of leakage. Check temperature
c) Clean heater exterior and interior. limiter.
3. Fuel system
a) Check fuel lines and connections for leaks. Check for leak-proof
b) Replace fuel filter cartridge with gasket. connections in fuel supply
and return!
c) If existing, open fuel shut-off valves. Retighten joints and hose
clamps.
d) Fuel pump Replace pump and lines

every 5years.
e) Replace fuel filter screen with gaskets in pump.
4. Burner head
a) Check combustion air inlet for contamination.
Swing burner head open:
b) Check cover for damage Replace damaged cover
c) Check housing interior for accumulation of fuel caused
by leaks.
d) Clean viewing glass of flame sensor.
e) Check igniter electrodes for condition. Replace bent electrodes.
f) Replace atomizer nozzle. When coked reduce

replacement interval for
fuel filter.
5. Exhaust system
a) Check exhaust line for contamination and clean as required.
b) Remove combustion chamber from heat exchanger, inspect both
components for damage and contamination and clean or replace
as required.
c) Insert combustion chamber and mount burner head. Check for secure
connection to heat exchanger.
d) Restore electrical connections.
6. Water system
a) If installed, clean water filter.
b) If installed, open water shut-off valves.
7. Functional checks
a) If installed, open shut-off valve in the return line.
b) Check heater function. after at least 10 min. of
heating operation.
c) Check for smoke emissions in run-down; replace nozzle if required.
* For rail applications consider the Maintenance Record RAIL 9008722B.
A-2
Spheros-Service
Sie haben ein technisches Problem? Spheros bietet Ihnen in Zusammenarbeit mit Webasto ein weltweites Servicenetz!
Spheros service telephone. Do you have a technical problem? Spheros offers in co-operation with Webasto a world-wide service net.
Spheros Spheros Webasto-Europa Webasto-Europa Webasto-Europa

BR Brasilien TR Trkei HR Kroatien IS Island SLO Slowenien
Spheros Brasil S.A. Spheros Thermo siehe Slowenien 210 Gardabaer 1000 Ljubljana
Tel. +55 54 21015700 Sistemleri A.S. Tel. +354 5672330 Tel. +386 1 2008710
Tel. +90 212 672 47 72 CH Schweiz
CND Canada 4123 Allschwil/BL KZ Kasachstan
Spheros North America, E Spanien Tel. +41 61 4869580 480019 Almaty
Inc., Canton, MI Spheros Europa Iberica Tel. +7 3272 312650
Webasto-Amerika
E-17451 Sant Feliu de CZ Tschechien
1-888-270-2226 140 00 Praha 4 Argentinien
Buixalleu, Girona L Luxemburg RA
Tel. +420 2 41045450-7 8263 BC Kampen (NL) 1424 Buenos Aires
RC China Tel. +34 972 874 923 Tel. +54 11 45242117
Spheros (Yangzhou) Tel. +31 38 3371 137
USA DK Dnemark
Limited USA RCH Chile
Spheros North America, DK-2610 Rdovre MK Mazedonien
Tel. +86 514 5881 226 Tel. +45 44 522000 OF907 Santiago de Chile
Inc., Canton, MI siehe Slowenien
Tel. +56 22 344311
D Deutschland 1-888-270-2226
EE Estland Niederlande
Gilching NL
ZA Sdafrika 11214 Tallinn 8263 BC Kampen
Tel. +49 8105 7721 887 Spheros SA (Pty) Ltd. Tel. +372 651 9309
[email protected] Tel. +27 21 761 9971
Tel. + 31 38 3371137 Webasto-Asien
www.spheros.de LV Lettland
1004 Riga N Norwegen RC China
UA Ukraine 1386 Asker Beijing
AE Dubai Spheros Elektron K. Ulmana gatve 2
Spheros Middle East Tel. +371 7807873 Tel. +47 66 753000 Tel. +852 28 118230
GU GmbH
Tel. +971 4 8860 665 Tel. +38 032 291 37 63
LT Litauen PL Polen J Japan
FIN Finnland 2300 Vilnius 05-092 Lomianki J-222-0033 Yokohama
Spheros Parabus Ltfd. Joioni g. 14 Tel. +48 22 7517787 +81 45 4741761
Tel. +358 2436 60 00 Webasto-Europa Tel. +370 5 275 81 81
RO Rumnien ROK Korea (Rep.)
IND Indien A sterreich F Frankreich 075100, Otopeni, llfov 626-140 Yangsan-si,
Spheros Motherson 1230 Wien 91280 Tigery Tel. +40 730 084 562 Gyeongsangnam-do
Thermal System Limited Tel. +43 1 6043780 Tel. +33 (0) 169 138383 Tel. +82 55 781 1002
Tel. +91 120 4346154 RUS Russland
B Belgien GB Grobritannien 107 065 Moscow MGL Mongolei
MY 8263 BC Kampen (NL) Dn4 5JH Doncaster Tel. +7 095 7770245 Ulaanbaatar
Malaysia
Tel. +31 38 3371 137 Tel. +44 1302 322232 Tel. +976 11 318138
Spheros (M) SDN BHD
Tel. +60 3 8961 5606 SRB Serbien und
GR Griechenland Montenegro
BIH Bosnien-Herzegovina CG
10442 Athen siehe Slowenien
MEX Mexiko siehe Slowenien Tel. +30 210 5196800
Spheros Mexico SK
Webasto-Australien
BG Bulgarien Slowakische Republik
Tel. +52 728 2 84 01 64 H Ungarn
1839 Sofia 04012 Koice AUS Australien
1135 Budapest Tel. +421 55 7871000
P Portugal Tel. +359 2 9420-555 Tel. +36 1 3502337 2232 NSW Kirrawee
Spheros Europa Iberica Tel. +61 2 85364800
BY
S Schweden
E-17451 Sant Feliu de Weirussland I Italien 19181 Sollentuna/ NZ Neuseeland
Buixalleu, Girona 220004 Minsk 40062 Molinella (BO) Stockholm 2232 NSW Kirrawee
Tel. +34 972 874 923 Tel. +37 50172201894 Tel. +39 051 690 6131 Tel. +46 8 923000 Tel. +61 2 85364800
Fr diese Druckschrift wurde ein
umweltschonendes, aus 100%
chlorfrei gebleichtem Zellstoff
hergestelltes Papier verwendet.
Printed in Germany 12.12

Druck: Steffendruck Friedland
nderungen vorbehalten
Subject to modification
Sous rserve de modifications
Spheros GmbH
Spheros GmbH
Friedrichshafener Strae 9-11 D-82205 Gilching
Tel. +49 (0) 8105 7721 887 Fax +49 (0) 8105 7721 889
www.spheros.de [email protected]
Technical Information
01-2008
Observance and affixing of the placard

Switch off auxiliary heating system before refuelling
Statutory regulations require that this placard, in the respective language of the
destination country, shall be affixed by the bus manufacturer near the fuel filler.
The bus operator shall observe this note categorically.
The placard in 9 languages and in the new Spheros-Design is provided with each
by the factory delivered SPHEROS-Heater since 21.07.08 as depicted. The placard
strip is attached securely to the heater by means of a clip as shown below and is
to be removed before installation.
Prepared on 21.07.08
Spheros Europa GmbH, After Sales Department
Friedrichshafener Strae 9-11, 82205 Gilching, Tel. +49 (0) 8105 7721 0 Fax +49 (0) 8105 7721 299
04-2008
Usage of the spare parts bag Small parts for magnetic

coil cpl., ident. no. 386650Z for heaters and
spare parts note for the new solenoid valve 2710806B
Please consider that the spare parts bag Small parts for magnetic coil
cpl., ident. no. 386650Z, may only be used for the below stated
heaters:
Heater Thermo 230/231/300/301/350, with magnetic coil ident. no. 29313_
Heater DBW 230 (2020)/300/350 for 12 V, version with magnetic coil ident. no. 322083
Heater DBW 230 (2020)/300/350/470 for 24 V, version with magnetic coil
ident. no. 322091
Otherwise the operation license of the heater will become invalid.
Spare parts note: The new solenoid valve 2710806B, which was included
into the heater series production, must be completely replaced if
required.
Old version of solenoid valve New solenoid valve 2710806B

prepared on 20.10.2008
Spheros Europa GmbH, Abteilung After Sales
Friedrichshafener Strae 9-11, 82205 Gilching,Tel.+49 (0) 8105 7721 887 Fax +49 (0) 8105 7721 889
05-2008
Splash water protection of magnetic clutch pumps

through technical changes
For all magnetic clutch pumps new / changed parts will be

provided:
- Shroud with changed design
- Additional gasket and a membrane
- The bearing splash guard is no longer used
By means of these technical changes the pump is

completely protected against splash water.
Affected are the Spheros circulation pumps U4818, U4854,

U4856, as well as the spare part kits magnetic clutch and the
spare part kits motor. The identification numbers of the items
remain unchanged.
05-2008
Shroud design changes
Shroud old Shroud new
05-2008
New gasket and membrane
New gasket New membrane
06-2008
Replacement of the solenoid valve

at DBW and Thermo Heaters
Old solenoid valve New solenoid valve
DBW 12 V --> 322083 + 2710247A 2710808A
DBW 24 V --> 322091 + 2710248A 2710807A
Thermo --> 29313_ 2710806B
SW 16 SW 8 SW 16 SW 12
(11.5 Nm) (2 Nm) (5 Nm) (1,5 Nm)
NOTE:
To replace the solenoid valve, first loosen the nut SW 8 resp. SW 12
(ref. figure) and remove the coil body. Thereafter the armature
sleeve SW 16 can be loosened more easily.
For installation reverse the sequence. Before installing the coil

body, the armature sleeve must be tightened. Torque to 5 Nm.
Then reinstall the coil body and fix it with the nut and torque as
prescribed (ref. figure).
Spheros Europa GmbH, After Sales
01-2009
(supersedes TI 07-2008)
Introduction of a new Electronic Ignition Unit

and a new Spare Parts Kit for Thermo Heaters
The new electronic ignition unit 2710213A supersedes the previous
version 14845C.
Do not reuse the combination screws M5x16 with spring ring when
replacing the old ignition unit 14845C by the new version 2710213A.
If required, please order in the future the 11113935A ignition unit

spare parts kit. It contains the ignition unit 2710213A and 2 ea
2710315A combination screw M5x16 (hexagon socket screw with
conical spring washer).
The amendment index of the heaters / burners will not be increased.

The implementation of the new ignition unit into the production is
accomplished in the middle of January 2009.
The ignition unit 2710213A is to

be installed with 2 combination
screws M5x16 (hexagon socket screw
with conical spring washer) only.
2710213A 2710315A
02-2009
Nozzle Block Preheater for Thermo Heaters

- Installation Notes for Heating Element Retrofit -
Spheros spare parts kit to be used:

86711B Retrofit bag heating element
Bag content:
- Heating element with thermostat
- Shield assy
- Retaining clamp
- Serrated lock washer
- Nut
Step 1:
Remove installed Further use delivered
shield shield
02-2009

Step 2:
Shield pre-assembly:
Position thermostat into the shield;
Install serrated lock washer and hand-tighten the nut.
For retaining clamp installation,

refer to step 3.
02-2009

Step 3: Substep 1:
Substep 2: Insert the heating element
Secure the heating element with the
retaining clamp
Substep 3:
Remove dummy connector; plug in the new connector
02-2009

Step 4:
Substep 1:
Place the pre-assembled shield onto the
Substep 2:
burner head and align it so the ignition
Install ignition electrodes
electrodes can be plugged in.
02-2009

Final result: Thermo heater with retrofitted heating element
Route cables as shown above

Attention:
Please consider during all other activities done at the heater
in regard to this retrofit the instructions given in the
workshop manual.
04-2009
(supersedes TI 03-2008)
Usage of new, optimized, downward compatible

Spheros atomizing nozzles for Thermo Heaters
Usage of hollow cone nozzles

Selected for Spheros quality optimized spray character / spray angle
Below of emission limitation permitted per law
Labeled with Spheros logo, heating power and identification number
Warranty and product liability only if genuine parts are used
Torque to 20 2 Nm;
(when tightening or loosen the nozzle, support the nozzle holder)
New Spheros identification numbers for Thermo Heaters 30 / 35 kW:

- 2710235B - atomizing nozzle 30 kW; (470724 still valid for DBW Heaters)
- 2710236B - atomizing nozzle 35 kW; (469556 still valid for DBW Heaters)
470716 atomizing nozzle 23 kW (without label)
still valid for Thermo and DBW Heaters
Sample view
STEINEN
SPHEROS 30kW 2710235
B
Technical Information 05-2009
New spare parts kit for the

current Spheros fuel pump
Please consider the following:
For repair purposes of the current Spheros fuel pump

11112615A the new identification no. 11113051A
(spare parts kit - gaskets) is to be used necessarily.
Content spare parts kit:

1 strainer 7,4-0,1 mm and 2 O-rings 7,65 x 1,78
For the previous fuel pump 82233A/B the 19977D

(small parts fuel pump bag 1 repair) resp. the
1302999B (small parts fuel pump bag 2 installation)
shall be further used.
Content kit 1 (standard repair kit - wear):

1 strainer 7,4-0,1 mm; 1 O-ring 5,28 x 1,78;
1 O-ring 7,65 x 1,78
Content kit 2 (assembly kit for nozzle holder sealing):

2 torx screws M4x12; 1 torx screw M4x20;
1 O-ring 2,9 x 1,78; 1 O-ring 33,08 x 1,78;
assembly instruction
Spheros Europa GmbH After Sales

Tel.+49 (0) 8105 7721 887 Fax +49 (0) 8105 7721 889 www.spheros.de [email protected] 09.11.2009
01-2010
New Spheros ident. no. for Small parts for magnetic coil
As of now, the spare parts kit Small parts for magnetic coil can be
ordered only, using the new Spheros ident. no. 11113599B (previously
386650Z).
The bag content remains unchanged, solely the package was adapted.
Pin Armature cpl.
Pressure spring O-ring
Please consider the Technical Information 04-2008 when using the

Small parts for magnetic coil.
13.01.2010
Friedrichshafener Strae 9-11, 82205 Gilching Tel.+49 (0) 8105 7721 887 Fax +49 (0) 8105 7721 889
Technical Information 02-2010
New Fuel Pumps for Thermo
Heaters
(please also note TI 2013_01)
Pumps to be Conversion kit to be

replaced - Application New Ident. Numbers ordered if required
Ident. No.
without heating pump: 11114892A
11112778B
element
82233A/B with heating pump: 11114892A

(only two-pipe element with heating element with 11112779B
operation) thermostat 83933B thermostat: 83933C
as vertical burner pump: 11114892A

(only Thermo 231.001 thermostat: 98640B 11112780B
+ 301.001) (for vertical burners)
without heating
element pump: 11114892A
11112778B
with heating
11112615A pump: 11114892A
element with (continue to use the 11112778B
(two-pipe
thermostat 83933C heating element 83933C)
operation)
as vertical burner pump: 11114892A

(only Thermo 231.001 (continue to use the 11112778B
+ 301.001) thermostat 98640B)
pump: 11114957A
11112615A
(continue to use the
(single-pipe 11114941A
heating element 83933C
operation)
and thermostat 98640B)
only heater
Thermo 230.060
pump: 11114957A
97952A/B/C
(heating element
(only single-pipe 83933C and thermostat
11114992A
operation) 98640B incl. shipment )
11114003A only heater

pump: 11114893A 11115017A
Thermo 350.190
03-2010
Heater reset after a lock-out and fault analysis
In the context of product quality monitoring and quality analysis we increased note the
submission of control devices which are ok (without any findings) in our plant in
Neubrandenburg.
Against this backdrop, we would like to advice you, that the deletion of saved faults by the
Spheros Thermo Test Diagnosis (ID. 11112249A) will not automatically remove the heater /
control device fault lock-out too.
To remove the heater fault lock-out the related instructions of the appropriate Thermo /
Thermo S Workshop Manual should be considered (see www.spheros.de/Service.Tech-
nische_Dokumente.Heizsysteme.aspx).
In this way you avoid unnecessary disassemblies and the respective effort (working time,
shipment, etc.).
Please note that the removal of the heater fault lock-out shall be accomplished by trained
personnel only. That includes also an investigation of the cause of the heater fault lock-out.
In order to process complaints faster and more efficient, please consider that the control
devices our heaters save the error codes. These codes then can be read out by the Spheros
Thermo Test Diagnosis and saved as text file.
Please attach this text file to your return consignment.
In this manner you support a purposeful and fast error code analysis as well the fault
remedy.
28.04.2010
05-2011
Service
Combustion Chamber Replacement in Thermo Series
Ongoing optimization of parts quality and the avoidance of unnecessary version

variety are firmly established in the product development process at Spheros.
Against this background, we point out that with a need for renewal or
replacement of a combustion chamber in one of the previous generation Thermo
230/300/350 heaters now the optimized version of Thermo S 230/300/350
heaters can be used.
In length and diameter it is identical to the Thermo

230/300/350 series.
The optimization lies in the two ring-
shaped reinforcements at the end of
the combustion chamber.
Advantages of Thermo S combustion chamber:

Prevention of warping due to thermal stresses during burner operation
Easier to disassemble the combustion chamber during maintenance
Reduce of the lifecycle costs due to significantly increased service life of the
combustion chamber (depending on operating conditions)
Spheros Recommendation
In future, during renewal of combustion chamber in Thermo 230/300/350
heaters, use new P/N 2710229A of Thermo S series.
06-2011
Service
Identification of GENUINE Spheros atomizing nozzles for heaters
Spheros label since Spheros ident. Heating power of the
2008 number heater (e.g. 35kW)
Nomenclature of production date recurring since 2008
1st letter => production month 2nd letter => production year
(A - January/M - December) (A - 2001/ K - 2010)
A => January G => July A => 2001 F => 2006

B => February H => August B => 2002 G => 2007
C => March I => September C => 2003 H => 2008
D => April K => October D => 2004 I => 2009
E => May L => November E => 2005 K => 2010
BK
F => June M => December from 2011 it starts with A
Feb 2010 again
A => 2011 B => 2012
!!! Attention: J does not exist!!!
Note: Under proper storage conditions of GENUINE Spheros atomizing

nozzles, the highest quality standards are guaranteed even with older
production date!
06-2011
Service
Overview on Spheros atomizing nozzles for heaters
Spheros
Series Designation Power Ident. number
label
160 16kW 2710233B yes
230 23kW 2710234B yes
Thermo S 300 30kW 2710235B yes
350 35kW 2710236B yes
400 40kW 2710237B yes
200 20kW 2711057A yes

Thermo E
320 32kW 2711056A yes
230 23kW 470716Z no

Thermo 300 30kW 2710235B yes
350 35kW 2710236B yes
DW 230 23kW 470716Z no

300 30kW 2710235B yes
350 35kW 2710236B yes
2020.26/31/65 23kW 341304Z no

2020.35 23kW 470716Z no
DBW 300.10 30kW 391697Z no
ab 300.18 30kW 470724Z no
ab 350.08 35kW 469556Z no
09-2012
Service
Initial start-up of Thermo, Thermo S and E Heaters
It is mandatory to read through the operating and maintenance instructions as well as the
installation instructions before starting the heater.
The safety precautions given in the above mentioned documents must be considered!
The heaters are adjusted in the factory and can be used unlimited without a change of the
CO2 adjustment up to an altitude of 1500 m above MSL and up to 2000 m above MSL if that
is a short stay in such conditions (pass crossing, break).
In case of a permanent heater operation above 1500 m the CO2 setting should be readjusted,
due to a negative change of the exhaust gas values in result of the decreased air density.
It is also recommended to adjust the CO2 content according to the technical data if
combustion air supply or exhaust gas applications are used.
After heater installation, bleed the water system and the fuel supply system carefully. In this
process it is mandatory to fill the suction line and the fuel filter of the heater completely.
Spheros recommends the usage of a separate bleeding unit. Follow the appropriate
instructions provided by the vehicle manufacturer. Verify the fuel supplied to the heater is
bubble-free.
NOTE:
Never use the fuel pump to fill / bleed the fuel system!
Generally, the hook-up of the heater to the vehicle power grid must be done only after filling
/ bleeding of the fuel system in order to prevent a premature start of the fan motor/fuel
pump.
Conduct a test run of the heater to check all the water and fuel connections for leaks and to
ensure that they are secure. If the heater suffers a fault during operation, the fault must be
located and remedied according to given in the shop manual instructions.
ATTENTION:
In the event no fuel comes to the fuel pump during initial start-up, there is a risk that the fuel
pump will be damaged!
30.09.2012
01-2013
Service
Overview fuel pumps for heaters

The optimized fuel pumps can clearly handle better fuel blowholes.
Blowholes in the fuel can originate by leakage in the bus fuel feed and also by gas
evolution in the fuel by elevated low-pressure.
Ignition miss and therefore the danger of heater locking will be reduced to a
minimum with the new pump.
The fuel pumps can be exchanged 1:1 in the field-

All spare part kits contain fastening bolts.
Spare-part-kit
Heater Fuel pump
fuel pump
23-35 kW 82233_
11112778C
23-35 kW 11114892_
Thermo 2-string
11112779C
23-35 kW 11114892_ Heating cartridge and
thermostate incl. (83933C)
16 kW 11114895_ 11118533A *
Thermo S 23-35 kW 2-string 11114896_ 11118534A *
40 kW 11114897_ 11118535A *
Thermo E 20-32 kW 2-string 11113950_ 11118536A *
* Scope of delivery incl. clutch
For heaters of the Thermo series we recommend to exchange als the old coupling
(20654A) with the new one (11117847A) together with the pump.
For 1-string pump demand, please contact us.
erstellt am 15.4.2013

Workshop Manual Thermo DW 300

Uploaded by

Copyright:

Available Formats

Workshop Manual Thermo DW 300

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Workshop Manual Thermo DW 300

Uploaded by

Copyright:

Available Formats

What is the purpose and scope of the manual?

What is the purpose and scope of the manual?

What are the main components of the water heaters described in the manual?

What are the main components of the water heaters described in the manual?

Water Heaters Workshop Manual

1.1 Scope and Purpose ............................................................................................................................... 101

1.5.1 General Safety Notes ................................................................................................................. 101

1.6 Legal Provisions for Installation ............................................................................................................. 102

2.1 Combustion Air Fan ............................................................................................................................... 202

2.2.1 Nozzle block preheater............................................................................................................... 203

2.3 Heat Exchanger ..................................................................................................................................... 203

2.12 Fuel Filter............................................................................................................................................... 206

3.1 Switch On .............................................................................................................................................. 302

Electrical components...................................................................................................................................... 401

5.1 General ................................................................................................................................................. 501

5.3.1 General ...................................................................................................................................... 503

6.1 General ................................................................................................................................................. 601

6.2.1 Adjustment of CO2 Contents ..................................................................................................... 601

6.3 Components Testing............................................................................................................................. 602

6.3.1 Temperature Sensor Resistance Check.................................................................................... 602

7.1 General ................................................................................................................................................. 701

8.1 General ................................................................................................................................................. 801

8.6 Visual Inspections and Regulations for Installation............................................................................... 804

8.6.1 Connection to Vehicle Cooling System ..................................................................................... 804

8.7 Removal and Installation....................................................................................................................... 807

8.7.1 Heater, Removal and Installation .............................................................................................. 807

8 7.5 Igniter Box, Replacement ........................................................................................................... 807

8.8 First Operation ....................................................................................................................................... 808

8.8.1 Water Circuit, Bleeding............................................................................................................... 808

9.1 General .................................................................................................................................................. 901

9.1.1 Work on Components after Disassembly ................................................................................... 902

9.2 Disassembly and Assembly................................................................................................................... 906

9.2.1 Temperature Limiter, Replacement ............................................................................................ 904

10. Packaging, Storage and Shipping

10.1 General ................................................................................................................................................ 1001

Heater, Scheduled Maintenance...................................................................................................................... A-2

501 General Fault Symptoms ................................................................................................................................ 501

801 Swinging Burner Head open ........................................................................................................................... 803

901 Temperature Limiter, Temperature Sensor and Burner, Replacement........................................................... 905

1. Introduction 1.4 Additional Documentation to be used

This workshop manual contains all information and

All fuel containers offered in the Spheros Accessories Ca-

Up to 4/03, General Design Certifications existed for these

nstallation is governed above all by the provisions in

1.7 Corrections and Improvements

Deficiencies, improvements, or proposals for correction of

Page empty for notes

2.1 Combustion Air Fan

Splash protection cover

2.2 Fuel Pump

The fuel pump is responsible for fuel supply.

a long fuel supply line

the fuel supply line must be filled prior to first heater

2.2.1 Nozzle block preheater

At extremely low temperatures malfunctions may occur

If the heater is not equipped with a nozzle block preheater

2.3 Heat Exchanger

2.4 Combustion Chamber

The fuel/air mix is dispersed in the combustion chamber

The flame sensor continuously monitors the flame