CH GATE'2017 Paper Key Solution PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 26

|CH| GATE-2017 www.gateforum.

com

Chemical Engineering
Q. No. 1 25 Carry One Mark Each

1. In a venturi meter, P1 and P2 are the pressure drops corresponding to volumetric flowrates
Q2 P2
Q1 and Q2 . If = 2, then equals
Q1 P1
(A) 2 (B) 4 (C) 0.5 (D) 0.25
Key: (B)
P fLQ2
Exp: = P Q2
g 12 D5
2
P2 Q 2 2
So = =2 =4
P1 Q1

2. The volumetric properties of two gases M and N are described by the generalized
compressibility chart which expresses the compressibility factor ( Z ) as a function of reduced
pressure and reduced temperature only. The operating pressure ( P ) and temperature ( T ) of
two gases M and N along with their critical properties ( PC ,TC ) are given in the table below.
Gas P ( bar ) T ( K ) PC ( bar ) TC ( K )
M 25 300 75 150
N 75 1000 225 500
ZM and Z N are the compressibility factor of the gases M and N under the given operating
conditions respectively.
The relation between ZM and z N is
(A) z M = 8ZN (B) ZM = 3ZN
(C) ZM = ZN (D) ZM = 0.333ZN
Key: (C)
Exp: For gas M; P = 25 bar, Pc = 75 bar
P 25 1
Pr = = =
PC 75 3
For Gas N; P = 75bar, PC = 225bar
75 1
Pr = =
225 3
T
For Gas M; T = 300K, TC = 150K, Tr = =2
TC
T
For Gas N, T = 1000K, TC = 500K, Tr = =2
TC
Pr
Compressibility factor, Z = k
Tr

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

1
K
Zm = =
3 K
2 6
1
K
Zn = = Z m = Z n
3 K
2 6

3. Match the polymerization process in Group-1 with the polymers in Group-2.


Group-1 Group-2
P) Free radical polymerization I) Nylon 6.6
Q) Ziegler Natta polymerization II) Polypropylene
R) Condensation polymerization III) Poly vinyl chloride

Choose the correct set of combinations.


(A) P I,Q II,R III (B) P III,Q II, R I
(C) P I, Q III, R II (D) P-II, Q-I, R-III
Key: (B)
Exp: P. Free Radical Polymerisation III) Poly Vinyl Chloride
Q. Zeigler Natta Polymerisation II) Polypropylene
R. condensation Polymerisation I) Nylon 6, 6

4. An LVDT (Linear Variable Differential Transformer) is a transducer used for converting

(A) displacement to voltage (B) Voltage to displacement


(C) resistance to voltage (D) voltage to current
Key: (A)
Exp: LVDT converts displacement to voltage.

5. Match the variables in Group-1 with the instruments in Group-2.


Group-1 Group-2
P) Temperature I) Capacitance probe
Q) Liquid level II) McLeod gauge
R) Vacuum III) Chromatograph
S) Concentration IV) Thermistor
Choose the correct set of combinations.
(A) P-IV,Q-III,R-II,S-I (B) P-I,Q-II,R-IV,S-III
(C) P-IV,Q-I,R-II,S-III (D) P-III,Q-II,R-I,S-IV
Key: (C)

6. The thickness of laminar boundary layer over a flat plate varies along the distance from the
leading edge of the plate. As the distance increases, the boundary layer thickness
(A) increases (B) decreases
(C) initially increases and then decreases (D) initially decreases and then increases
Key: (A)

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

7. The marks obtained by a set of students are 38, 84, 45,70, 75, 60, 48.
The mean and median marks, respectively, are

(A) 45 and 75 (B) 55 and 48


(C) 60 and 60 (D) 60 and 70
Key: (C)
38 + 84 + 45 + 70 + 75 + 60 + 48
Exp: Mean = = 60
7
In ascending order
38, 45, 48, 60, 70, 75, 84
Median = Middle most observation= 60

8. In a heat exchanger, the inner diameter of a tube is 25 mm and its outer diameter is 30 mm.
The overall heat transfer coefficient based on the inner area is 360 W/m2.OC. Then, the overall
heat transfer coefficient based on the outer area, rounded to the nearest integer, is ___
W/m2.OC.
Key: 300
Exp: Di = 25mm
D O = 30 mm
Vi = 360 W
m2 O C
Vi A i = VO A O
Ai D 25
VO = Vi = Vi i = 360 = 300 W 2 O
AO D0 30 m . C

9. The cost of a new pump (including installation) is 24,000 Rupees. The pump has useful life of
10 years. Its salvage value is 4000 Rupees. Assuming straight line depreciation, the book
value of the pump at the end of 4th year, rounded to the nearest integer, is ___ Rupees.
Key: 16000
Exp: Cost of new pump = Rs. 24000
Useful life of pump = 10 years
Salvage value of pump at the end of service life = 4000
Annual Depreciation using straight line method = (24000-4000)/10 = 2000 Rs
Book Value at the end of 4th year = Cost of equipment Accumulated Depreciation till the
end of 4th year
= 24000- (4*Annual depreciation)
= 24000-(4*2000)
=24000-8000
= 16000 Rs

10. A gas bubble (gas density g = 2 kg / m 3 ; bubble diameter D = 104 m ) is rising vertically
through water (density = 1000 kg / m3 ; viscosity = 0.001 Pa.s ). Force balance on the
bubble leads to the following equation,

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

d g 18
= g
dt g g D 2
Where is the velocity of the bubble at any given time t. Assume that the volume of the
rising bubble does not change. The value of g = 9.81m / s 2 .
The terminal rising velocity of the bubble (in cm/s), rounded to 2 decimal places, is ___ cm/s.
Key: 0.54
Exp: At terminal missing velocity
d g 18
= 0 = g
dt g g D 2
We get,
gD 2 ( g ) 9.81 (104 )2 (1000 2)
= = = 5.439 103 m / s = 0.54 cm / s
18 18(0.001)

11. Water is heated at atmospheric pressure from 40OC to 80OC using two different processes. In
process I, the heating is done by a source at 80OC. In process II, the water is first heated from
40OC to 60OC by a source at 60OC, and then from 60OC to 80OC by another source at 80OC.
Identify the correct statement.
(A) Enthalpy change of water in process I is greater than enthalpy change in process II
(B) Enthalpy change of water in process II is greater than enthalpy change in process I
(C) Process I is closer to reversibility
(D) Process II is closer to reversibility
Key: (D)

12. The DCDA (Double Contact Double Absorption) process is used the manufacture of

(A) Urea (B) Sulphuric acid (C) nitric acid (D) ammonia
Key: (B)
Exp: The contact process is the current method of producing sulphuric acid in the high
concentrations needed for industrial processes. Platinum used to be the catalyst for this
reaction; however, as it is susceptible to reacting with arsenic impurities in the sulphuric
feedstock, vanadium (V) oxide (V2O5) is now preferred.

13. The real part of 6ei /3 is ___.


Key: 3
i

Exp: 6e 3 = 6 cos + isin = 6cos + i 6sin
3 3 3 3
1
Real part = 6cos = 6 = 3
3 2

14. Consider a first order catalytic reaction in a porous catalyst pellet.


Given R - characteristic length of the pellet: De - effective diffusivity; k C - mass transfer
coefficient: k1 - rate constant based on volume of the catalyst pellet; Cs - concentration of
reactant on the pellet surface.
 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

The expression for Thiele modulus is


kCR k1 k1Cs De
(A) (B) R (C) R (D) R
De De De k1
Key: (B)

15. Which of the following conditions are valid at the plait point?
P) Density difference between the extract and raffinate phases is zero
Q) Interfacial tension between the extract and raffinate phases is zero
R) Composition difference between the extract and raffinate phases is zero
(A) P and Q only (B) Q and R only (C) P and R only (D) P, Q and R
Key: (D)
Exp: Plait point signifies the condition at which the composition of two liquid phases in
equilibrium become identical and indeed transforms to a single phase. At this point interfacial
tension and density difference between extract and raffinate phase is zero as both phases
united to form one phase.

16. The purpose of the mathanation reaction used in ammonia plants is to


(A) remove CO as it is a catalyst poison
(B) increase the amount of hydrogen
(C) remove sulphur as it is catalyst poison
(D) utilize methane as a catalyst for ammonia synthesis
Key: (A)

17. Which of the following is the correct sequence of equipment for size reduction of solids?
(A) (B) Hammer mill
Fluid energy mill

Jaw crusher Jaw crusher

Hammer mill
Fluid energy mill

(C) Fluid energy mill (D) Jaw crusher

Hammer mill Hammer mill

Jaw crusher Fluid energy mill

Key: (D)
Exp: Solid is crushed into intermediate by jaw crusher after which grinding of solid is done by
hammer mill. Ultrafine grinding is done by fluid energy mill.

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

18. Let i and j be the unit vectors in the x and y directions, respectively. For the function
F ( x, y ) = x 3 + y 2
the gradient of the function i.e.. F is given by
(A) 3x 2 i 2y j (B) 6x 2 y
(C) 3x 2 i+2 y j (D) 2 y i-3 x 2 j
Key: (C)
F F
Exp: F = i + j = i ( 3x 2 ) + j ( 2y )
x y

19. Consider steady state mass transfer of a solute A from a gas phase to a liquid phase. The gas
phase bulk and interface mole fractions are y A,G and y A,i respectively. The liquid phase bulk

and interface mole fractions are x A,L and x A,i , respectively. The ratio
(x A,i x A,L )
is very
(y A,G y A,i )
close to zero.

The implies that mass transfer resistance is


(A) negligible in the gas phase only (B) negligible in the liquid phase only
(C) negligible in both the phases (D) considerable in both the phases
Key: (B)

Exp: Here
(x A,i x A,L )
=0
(y A,G y A,i )
Or x A,i x A,L = 0
x A,i = x A,L
Mole fraction of liquid phase interface is equal to mole fraction of liquid phase bulk.
It means resistance in the liquid phase is negligible.
Option (B) is correct

tan ( x )
20. The value of lim is _____.
x 0 x
Key: 1
tan x
Exp: lim =1
x 0 x

21. For a solid-catalyzed gas phase reversible reaction, which of the following statements is
ALWAYS TRUE?
(A) Adsorption is rate-limiting
(B) Desorption is rate-limiting
(C) Solid catalyst does not affect equilibrium conversion
(D) Temperature does not affect equilibrium conversion
Key: (C)
Exp: Solid catalyst does not effect the equilibrium conversion.

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

22. The one-dimensional unsteady heat conduction equation is


T 1 n T
C P= r k
t r n r r
Where, T temperature, t time, r radial position, k thermal conductivity, - density, and
Cp - specific heat.
For the cylindrical coordinate system, the value of n in the above equation is

(A) 0 (B) 1 (C) 2 (D) 3


Key: (B)
Exp: n = 1 for cylindrical coordinate system
1 T T
rk = Cp
r r r t

23. The composition of vapour entering a tray in a distillation column is 0.47. The average
composition of the vapour leaving the tray is 0.53. The equilibrium composition of the vapour
corresponding to the liquid leaving this tray is 0.52. All the compositions are expressed in
mole fraction of the more volatile component.

The Murphree efficiency based on the vapour phase, rounded to the nearest integer, is ___ %.
Key: 120
Exp: Murphree efficiency is defined as the actual change in average composition accomplished by
y1 y
a given tray divided by the change in average composition. m =
ye y
0.53 0.47
m = 100 = 120%
0.52 0.47
Where,
y1 = Average composition of vapour leaving the tray.
ye = Equilibrium composition of vapour corresponding to the liquid leaving the tray.
y = Composition of vapour entering the tray.

24. The number of positive roots of the function f ( x ) shown below in the range 0 < x < 6 is
___________.
150
120
90
60
f(x)

30
0
0 2 4 6 8 10
30

60
x

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

Key: 3
Exp: The graph of the function cuts x axis in 3 times in 0 < x < 6
The no. of positive roots=3

25. The following reaction rate curve is shown for a reaction A P. Here, ( rA ) and x A
represent reaction rate and conversion, respectively. The feed is pure A and 90% conversion
is desired

1
rA

0 0.2 0.4 0.6 0.8 1


XA
Which amongst the following reactor configurations gives the lowest total volume of the
reactor (s)?
(A) CSTR followed by PFR (B) Two CSTRs in series
(C) PFR followed by CSTR (D) A single PFR
Key: (A)
Exp: The performance equation for a PFR
XA
V dX A
=
CAo FAo
=
0 rA
Hence the volume required for the reactor for given conversion is
XA
dX A
V = FAo 0
rA
1
Which is the area under curve between versus X A
rA
The performance equation for a CSTR
V XA
= =
C Ao FAo rA
Hence the volume required for the reactor for given conversion is
X
V = FAo A
rA
1
Which is the volume of rectangle drawn on the graph between versus X A for the given
rA
conversion.
For the given reaction,
 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

The following options give the following volumes


Set up Volume
CSTR followed by PFR Area of rectangle from 0 to 0.5 and area under
curve from 0.5 to 1
Two CSTRs in series Area of two rectangles (from 0 to 0.5 and 0.5 to 1)
PFR followed by CSTR Area under curve from 0 to 0.5 and area of
rectangle from 0.5 to 1
A single PFR Area under the curve.
Its clearly shown the combination of CSTR followed by PFR
Hence answer is Option (A).

Q. No. 26 to 55 Carry Two Marks Each

26. The total cost ( CT ) of an equipment in terms of the operation variables x and y is
12000
CT = 2x + +y+5
xy
The optimal value of CT , rounded to 1 decimal place, is ____.
Key: 91.5
Exp: The total cost of an equipment in terms of the operating variables x and y is
12000
CT = 2x + + y+5
xy
To find optimum value of CT,
CT 12000
=02 2 =0
x x y
2x 2 y = 12000 (1)
and
CT 12000
= 0 1 =0
y xy 2
xy 2 = 12000 (2)
Solving equation (1) and (2) yields
X=14.4 and y= 28.8
Hence the optimum value of CT is 91.5

27. The vapour pressure of a pure substance at a temperature T is 30bar. The actual and ideal gas
values of g / RT for the saturated vapour at this temperature T and 30 bar are 7.0 and 7.7
respectively. Here, g is the molar Gibbs free energy and R is the universal gas constant.
The fugacity of the saturated liquid at these conditions, rounded to 1 decimal place, is ___
bar.
Key: 14.9
g g
Exp: = 7, = 7.7
RT RT
As we know

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

fi gR
x = = exp
p RT
gR g g
= = 7 7.7
RT RT RT ig
gR f
= 0.7 = i = p ( 0.7 )
RT P
f i = 30exp ( 0.7 ) = 14.9 bar

28. The Sherwood number ( Sh L ) correlation for laminar flow over a flat plate of length L is
given by
1
Sh L = 0.664 Re0.5
L Sc
3

Where Re L and Sc represent Reynolds number and Schmidt number, respectively.


This correlation, expressed in the form of Chilton-Colburn jD factor, is
(A) jD = 0.664 (B) jD = 0.664 Re L0.5
2
(C) jD = 0.664 ReL (D) jD = 0.664 Re0.5
L Sc
3

Key: (B)
1

L Sc (1)
Sh L = 0.664 Re0.5 3
Exp:
Sh L
Chilton- Coburn factor jD = 1
Re L Sc 3
1
Sh L = jD .ReL .Sc 3 ( 2 )
From equation (1) & (2)
1 1
jD Re L .Sc 3 = 0.664 Re L 0.5 Sc 3
jD = 0.664 Re L0.5

29. For the initial value problem


dx
= sin ( t ) , x ( 0 ) = 0
dt
the value of x at t = , is ____.
3
Key: 0.5
dx
Exp: = sin t dx = sin t dt x = cos t + C
dt
Given,
x ( 0 ) = 0 at t = 0 x = 0 0 = 1 + C C = 1
x = cos t + 1
1 1
at t = , x = cos + 1 = + 1 = = 0.5
3 3 2 2

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

30. In a counter current stripping operation using pure steam the mole ratio of a solute in the
liquid stream is reduced from 0.25 to 0.05. The liquid feed flowrate, on a solute-free basis, is
3mole/s. The equilibrium line for the system is given in the figure below.

0.15

Mole ratio in the gas phase, Y


0.1

equilibrium line

0.05

0
0 0.05 0.1 0.15 0.2 0.25
Mole ratio in the liquid phase, X
The MINIMUM flowrate of pure steam for this process, rounded to 1 decimal place, is ___
mol/s.
Key: 4
Exp: Equation of equilibrium line can be written as y = mX
0.15
m=slope of equilibrium line = = 0.6
0.25
y = 0.6X
Material balance of solute gives L ( 0.25 0.05 ) = G min 0.6 ( 0.25 )
Here, L = 3mol / sec, G = minimum flow rate of pure steam
3 ( 0.25 0.05 )
G min = = 4 mol / sec
0.6 ( 0.25 )
S +1
31. The Laplace transform of a function is . The initial and final values,
S (S + 2 )
respectively, of the function are
1 1 1
(A) 0 and 1 (B) 1 and (C) and 1 (D) and 0
2 2 2
Key: (B)
1
S 1 +
= lim
S +1 S 1+ 0
Exp: For initial value, finding lim SF ( S) = limS = =1
s s S(S + 2) s 2 1+ 0
S 1 +
S
S +1 1
For finalvalue, Finding limSF ( S) = limS =
s 0 s0 S ( S + 2 ) 2

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

32. The following table provides four sets of Fanning friction factor data, for different values of
k
Reynolds number (Re) and roughness factor .
D
Re 102 103 105 105
k
0 0.001 0 0.001
D
Set I f 0.16 0.016 16 105 16 105
Set II f 0.016 0.16 0.0055 0.0045
Set III f 0.16 0.016 0.0045 0.0055
Set IV f 0.0045 0.0055 0.016 0.16
Which of the above sets of friction factor data is correct?
(A) Set 1 (B) Set II (C) Set III (D) Set IV
Key: (C)

33. In a batch adsorption process, 5 g of fresh adsorbent is used to treat 1 litre of an aqueous
phenol solution. The initial phenol concentration is 100 mg/litre. The equilibrium relation is
given by q* = 1.3C
Where, q* is the amount of phenol adsorbed in mg of phenol per gram of adsorbent: and C is
the concentration of phenol in mg/litre in the aqueous solution.
When equilibrium is attained between the adsorbent and the solution, the concentration of
phenol in the solution, rounded to 1 decimal place is ___________ mg/litre.
Key: 13.34
Exp: Suppose y mg of phenol is adsorbed
Amount of phenol adsorbed in mg y
q* = =
wt.of fresh adsorbent 5
q* = 1.3C
C =100 y
y
= 1.3 (100 y )
5
0.15384y = 100 y
y = 86.66 mg
Concentration of phenol in solution = 100 86.66 = 13.34 mg / lt

34. A bond has a maturity value of 20,000 Rupees at the end of 4 years. The interest is
compounded at the rate of 5% per year.
The initial investment to be made, rounded to the nearest integer, is _______ Rupees.
Key: 16454
Exp: Maturity value = 20000
Bond life = 4 years
Interest rate = 5%
Amount of investment to be made can be found from present worth formula
= 20000/(1+0.05)^4=16454.04=16454 Rs

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

35. Size analysis was carried out on a sample of gravel. The data for mass fraction ( x i ) and
average particle diameter ( D pi ) of the fraction is given in the table below:
xi DPi (mm)
0.2 5
0.4 10
0.4 20
The mass mean diameter of the sample, to the nearest integer, is ________mm.
Key: 13
Exp: xi = 1
Mass mean diameter of sample
= x i D pi / xi = ( 0.2 5 ) + ( 0.4 10 ) + ( 0.4 20 ) = 13mm

36. A propeller (diameter D = 15 m) rotates at N = 1 revolution per second (rps). To understand


the flow around the propeller, a lab-scale model is made. Important parameters to study the
flow are velocity of the propeller tip ( V = ND ) , diameter D and acceleration due to gravity
(g). The lab-scale model is 1/100th of the size of the actual propeller.
The rotation speed of the lab-scale model, to the nearest integer, should be _________ rps.
Key: 10.0

37. The transfer function of a system is


1
4S2 + 1.2S + 1
For a unit step increase in the input, the fractional overshoot, rounded to 2 decimal places, is
______.
Key: 0.37
1
1 4 0.25
Exp: Transfer function = 2 = 2
4S + 1.2S + 1 4 1.2 1 S + 0.3S + 0.2S
S2 + S+
4 4 4
Denominator is in the form of S2 + 2n S + n 2
We can infer n 2 = 0.25
n = 0.25 = 0.5
and 2 n S = 0.3
0.3
damping ratio , = = 0.3
2 0.5

Peak over shoot = 100
1 2
0.3
= 100 = 0.37%
2
1 ( 0.3)

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

38. A fluid over a heated horizontal plate maintained at temperature Tw . The bulk temperature of
the fluid is T . The temperature profile in the thermal boundary layer is given by:
1 y 3 3 y
T = Tw + ( Tw T ) , 0 y t
2 t 2 t
Here, y is the vertical distance from the plate, t is the thickness of the thermal boundary
layer and k is the thermal conductivity of the fluid.
The local heat transfer coefficient is given by
k k 3 k k
(A) (B) (C) (D) 2
2 t t 2 t t
Key: (C)
1 3

T = Tk1 + ( Tk1 T ) y y , 0 y t
3
Exp:

2 t 2 t
T
k = h ( Tw T )
y y=0

3
k ( Tw T ) = h ( Tw T )
2 t
3k
=h
2 t

39. The following liquid second-order reaction is carried out in an isothermal CSTR at steady
state A R ( rA ) = 0.005CA 2 mol / m 3 .hr
Where, C A is the concentration of the reactant in the CSTR. The reactor volume is 2 m 3 , the
inlet flow rate is 0.5 m3 / hr and the inlet concentration of the reactant is 1000mol / m3 .
The fractional conversion, rounded to 2 decimal places, is _____.
Key: 0.80
Exp: For a CSTR, The performance equation can be written as
V/Fo= T/CAo=XA/-rA
V/Vo= T=CAo. XA/-rA
(2/0.5)= (CAo XA)/(0.005C2A)
4= (CAo XA)/(0.005C2Ao(1- XA)2)
Solving this equation yields, XA as 0.80 or 80%.

40. Reaction A B is carried out in a reactor operating at steady state and 1 mol/s of pure A at
425C enters the reactor. The outlet stream leaves the reactor at 325OC. The heat input to the
reactor is 17kW. The heat of reaction at the reference temperature of 25C is 30kJ/mol. The
specific heat capacities (in kJ/mol.K) of A and B are 0.1 and 0.15, respectively.
The molar flowrate of B leaving the reactor, rounded to 2 decimal places, is ____mol/s.
Key: 0.6
Exp: AB
Suppose X be the conversion of reactant

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

T1 = 4250 C, H x = 30 kJ / mol = 30000 J / mol


Q = 17 kW = 17000J, T2 = 3250 C
Trpf = 250 C, FAo = 1mol / sec, FA = (1 x ) FAo
C PA = 0.1 kJ / mol, C PB = 0.15 kJ / mol, FB = x FAo
Heat balance gives
FAo C PA ( T2 Trpf ) = FA C PA ( T2 Trpf ) + FB C PB ( T2 Trpf )
1 0.1( 425 25 ) = 0.1(1 x )( 325 25 ) + x ( 0.15 )( 325 25 )
40 = 30 (1 x ) + 45x
X = 0.6
FB = FAo X = 0.6 (1) = 0.6 mol / sec

41. The C-curve measured during a pulse tracer experiment is shown below. In the figure, C(t) is
the concentration of the tracer measured at the reactor exit in mol/liter at time t seconds.
1.5

1
C(t)

0.5

0 1 2 3
t
The mean residence time in the reactor, rounded to 1 decimal place, is ______ s.
Key: 1.0
Exp: The data can be drawn from the diagram is as follows
C(t) t t. C(t)
0 0 0
1 1 1
0 2 0
Mean residence time = t. C/C = (0+1+0)/(0+1+0)=1s

42. The reversible reaction of t-butyl alcohol (TBA) and ethanol (EtOH) to ethylt-butyl ether
(ETBE) is
TBA + EtOH  ETBE + Water
The equilibrium constant for this reaction is K C = 1 . Initially, 74 g of TBA is mixed with
100g of aqueous solution containing 46 weight% ethanol. The molecular weights are:74g/mol
for TBA. 46g/mol for EtOH, 102g/mol for ETBE, and 18 g/mol for water.
The mass of ETBE at equilibrium, rounded to 1 decimal place, is ____g.
Key: 20.4

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

Exp: Let x mole of ETBE present of equilibrium mass of EtOH=46 g


Mass of water = 54g
46
Moles of EtOH = = 1 mol
46
54
Moles of water = 3mol
18
TBA + EtOH  ETBE + water
At t=0 1 1 0 3
At equilibrium 1 x 1 x x 3+ x

Kc =
( 3 + x )( x ) = 1
(1 x )(1 x )
x = 0.2
Moles of ETBE=0.2
Moles of ETBE = 0.2 (102 ) = 20.4gm

43. Let Ib be the spectral black body radiation intensity per unit wavelength about the wavelength .
The blackbody radiation intensity emitted by a blackbody over all wavelengths is
dI b d 2 I b
(A) (B) 2
(C) Ib d (D) Ib d
d d 0 0

Key: (C)

Exp: Ib = I b d
0

44. Match the equipment in Group-1 with the process in Group-2:


Group-1 Group-2
(P) Fluidized bed (I) Paper-making
(Q) Multistage adiabatic reactor with (II) Sodium hydroxide manufacturer
Inter-stage cooling
(R) Fourdrinier machine (III) SO2 oxidation
(S) Diaphragm cell (IV) Catalytic cracking
Choose the correct set of combinations.
(A) P IV,Q III, R I,S II (B) P IV,Q III,R II,S I
(C) P III, Q IV, R I,S II (D) P III, Q IV, R II,S I
Key: (A)

45. Oil is being delivered at a steady state flowrate through a circular pipe of a radius
1.25 102 m and length 10m. The pressure drop access the pipe is 500 Pa.
The shear stress at the pipe wall, rounded to 2 decimal places______ Pa
Key: 0.3125
Exp: r = 1.25 102 m
L = 10 m, P = 500 pa, C w = ?
2
P r 500 1.25 10
Cw = = = 0.3125 pa
L 2 10

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

46. Match the problem type in Group-1 with the numerical method in Group-2
Group-1 Group-2
(P) System of linear algebraic equations (I) Newton-Raphson
(Q) Non-linear algebraic equations (II) Gauss-seidel
(R) Ordinary differential equations (III) Simphsons Rule
(S) Nemerical integrations (IV) Runge-Kutta
Choose the correct set of combinations.
(A) P II,Q I, R III,S IV (B) P I,Q II, R IV,S III
(C) P IV,Q III, R II,S I (D) P II,Q I, R IV,S III
Key: (D)

47. The following gas-phase reaction is carried out in a constant-volume isothermal batch reactor
A+ B R +S
The reactants A and B as well as the product S are non-condensable gases. At the operating
temperature, the saturation pressure of the product R is 40 kPa.
Initially, the batch reactor contains equimolar amounts of A and B (and no products) at a total
pressure of 100 kPa. The initial concentrations of the reactants are
C A,0 = CB,0 = 12.56 mol / m3 . The rate of reaction is given by ( rA ) = 0.08C A CB mol / m3 .s .
The time at which R just starts condensing, rounded to 1 decimal place, is_____
Key: 4
Exp: A+ BR +S
Let m moles of A and B present initially in the reactor
Initially m, m 0,0
After time t, m xm, m xm mx mx
Total moles after time t= mx + mx + m mx + m mx = 2m
( mx ) Pt Pt x
Partial pressure of R at time t = = = PR
2m 2

At Pr = 40 kPa. R will start conden sin g


100(x)
Here, Pt = 100kPa, PR = 40 =
2
x = 0.8
C A = C A0 (1 X) = 1.25(1 0.8)
C A = 2.5mol / m 3
CA dC A
Batch reactor t =
CA 0 0.08C A 2
1 1 1 1 1 1
t= = t = 4sec
0.08 C A C A0 0.08 2.5 12.5

48. The vapor phase composition and relative volatilities (with respect to n-propane) on an ideal
tray of a distillation column are

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

Component Methane Ethane n-Propane

Mole fraction in 0.12 0.28 0.60


vapour
Relative volatility 10 4 1

The mole fraction of n-propane in the liquid phase, rounded to 2 decimal places, is ____.
Key: 0.88
Exp: yA = 0.12, yB = 0.28, yC = 0.60
y A x C 0.12 x C
AC = 10 = = = 10
yC x A 0.60
xA + xB + xC = 1
xA = 1 xB xC
0.12x C
We get, = 10
0.60 (1 x B x C )
x B = 1 1.02 x C (1)
yB xC 0.2 x C
BC = 4 = =4
y C x B 0.60 (1 0.02 x C )
We get x C = 0.88

49. The Characteristic equation of a closed-loop system is


6s3 + 11s 2 + 6s + (1 + k ) = 0, Where, k > 0
The value of K beyond which the system just becomes unstable, rounded to the nearest
integer, is _____.
Key: 10
Exp: Characteristic equation
6S3 + 11S2 + 6S + (1 + k ) = 0
Use R-H criteria to find the value of k.
S3 6 11
S2 11 (1 + k )
66 6 (1 + k )
S1 0
11
S0 (1 + k )
66 6 (1 + k )
=0
11
66 6 (1 + k ) = 0
66 = 6 (1 + k )
11 = 1 + k k = 11 1 = 10
The value is 10.

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

50. A aqueous salt-solution enters a crystallizer operating at steady state at 25O C . The feed
temperature is 900 C and the salt concentration in the feed is 40 weight%. The salt
crystallizes as a pentahydrate. The crystals and the mother liquor leave the crystallizer. The
molecular weight of the anhydrous salt is 135. The solubility of the salt at 25O C is 20
weight%.
The feed flowrate required for a production rate of 100 kg/s of hydrated salt, rounded to the
nearest integer, is ____ kg/s.
Key: 200
Exp: x F = Salt concentration in the feed ( wt.% ) = 0.4
Molecular wt. of 5H 2 O molecules = 18 5 = 90
Molecular wt. of the anhydrous salt= 135
135
x C = wt% of hydrated crystal = 0.6
90 + 135
x L = Solubility of salt=0.2
Total Mass balance gives
M Feed = M hydrated crystal + M mother liquor
M Feed = 100 + M Mother liquor (1)
Mass balance of salt gives
0.4M Feed = 0.6 (100 ) + 0.2 M mother liquor
0.4M Feed = 60 + 0.2M mother liquor ( 2 )
On solving (1) and (2) we get
M feed = 200 kg / s

51. The pressure of a liquid is increased isothermally. The molar volume of the liquid decreases
from 50.45 106 m3 / mol to 48 106 m3 / mol during this process. The isothermal
compressibility of the liquid is 109 Pa 1 , which can be assumed to be independent of
pressure.
The change in the molar Gibbs free energy of the liquid, rounded to nearest integer, is ___
J/mol.
Key: 2511.4
1 dv
Exp: As we know = (1)
V dp T
For isothermal process pv = const
dv V
Pdv + Vdp = 0 =
dp P1
From equation(1)
1 1
= P1 = = 109 Pa
P1
At constant temperature

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

RT
dG = Vdp SdT dG = VdP = dP
P
P P V
DG = RT ln 2 ; P1V1 = P2 V2 2 = 1
P1 P1 V2
P1V1 = RT
V
DG = P1V1 ln 1
V2
P1 = 10 pa, V1 = 50.45 106 m3 / mol
9

V2 = 48 106 m3 / mol
50.45 106
G = 109 ( 50.45 106 ) ln 6
48 10
G = 50.45 10 ln (1.051)
3

G = 2511.48 J / mole

52. The open loop transfer function of a process with a proportional controller (gain K C ) is
e 2s
G OL = K C
s
Based on the Bode criterion for closed-loop stability, the ultimate gain of the controller,
rounded to 2 decimal places, is____.
Key: 0.78
e 2s
Exp: G OL = K C
s
At ultimate gain.
phase angle is - 1800
2
= tan 1 (180 ) = 1800
0
2
90 (180 ) = 180


=
4
1
Amplitude ratio ( AR ) = K C (1)

K
AR = C

At ultimate gain AR is 1
( K C )4
=1

3.14
( K C )4 = = =
4 4
( K C )4 = 0.785

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

53. In nucleate boiling, the pressure inside a bubble is higher than the pressure of the surrounding
liquid. Assuming that both the liquid and vapour are saturated, the temperature of the liquid
will ALWAYS be
(A) at 100O C
(B) lower than the temperature of the vapour
(C) equal to the temperature of the vapour
(D) higher than the temperature of the vapour
Key: (B)
Exp: The temperature of the liquid will always be lower than the temperature of the vapour

54. A box has 6 red balls and 4 white balls. A ball is picked at random and replaced in the box,
after which a second ball is picked.
The probability of both the balls being red, rounded to 2 decimal places, is ____.
Key: 0.36
6 6 36
Exp: Required probability = = = 0.36
10 10 100

55. A sparingly soluble gas (solute) is in equilibrium with a solvent at 10 bar. The mole fraction
of the solvent in the gas phase is 0.01. At the operating temperature and pressure, the fugacity
coefficient of the solute in the gas phase and the Henrys law constant are 0.92 and 1000 bar,
respectively. Assume that the liquid phase obeys Henrys law.
The MOLE PERCENTAGE of the solute in the liquid phase, rounded to 2 decimal places, is
_____.
Key: 0.91
Exp: H = 1000 bar, = 0.92 for dilute solution
We can use Henry law for solute H x = yP
1000 x = 0.92 (1 0.01)(10 )
Here, y and x are mole fraction of solute in gas and liquid phase respectively
x = 9.108 103
Mole percentage of solute in liquid phase = 100 9.108 103 = 0.91 ( )
General Aptitude
Q. No. 1 - 5 Carry One Mark Each

1. Consider the following sentences:


All benches are beds. No bed is a bulb. Some bulbs are lamps.
Which of the following can be inferred?
(i) Some beds are lamps.
(ii) Some lamps are beds.
(A) Only i (B) Only ii
(C) Both i and ii (D) Neither i nor ii
Key: (D)

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

Exp: Beds
Ben Beds Bulbs Bulbs lamps
ches

A B C
Since, there is no direct relation given between lamps and beds. So, neither will be correct.

2. The following sequence of numbers is arranged in increasing order: 1, x, x, x, y, y,9,16,18.


Given that the mean and median are equal, and are also equal to twice the mode, the value of
y is
(A) 5 (B) 6 (C) 7 (D) 8
Key: (D)
Exp: Given, Mean = Median = 2Mode
Mean = Median = 2x [ Mode = x ] (1)
3x + 2y + 44
Mean of the data =
9
3x + 2y + 44
2x = 15x 2y = 44 (2)
9
Median of the data = y (3)
y = 2x (4) [ Median = 2Mode ]
From (2);11x = 44
x = 4; y = 8

3. The bacteria in milk are destroyed when it _________ heated to 80 degree Celsius.
(A) would be (B) will be (C) is (D) was
Key: (C)

4. If the radius of a right circular cone is increased by 50%, its volume increases by
(A) 75% (B) 100% (C) 125%` (D) 237.5%
Key: (C)
Exp: Given, radius of a right circular cone is increased by 50%.
Let, height of the circular cone =(h)
1
Initially, Volume of the cone= r 2 h (1)
3
1 2 2
New volume of the cone= r (1.5r ) h (2)
3
1 2 1
From (1) and (2); r h = ( 2.25 ) r 2 h
3 3

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

1 2 1
r h (2.25)r 2 h
3 3
1 1.25 2.25

1.25
Required percentage= 1 100 % = 125%

5. __________ with someone elses email account is now very serious offence.
(A) Involving (B) Assisting (C) Tampering (D) Incubating
Key: (C)

Q. No. 6- 10 Carry Two Marks Each

6. Students applying for hostel rooms are allotted rooms in order of seniority. Students already
staying in a room will move if they get a room in their preferred list. Preferences of lower
ranked applicants are ignored during allocation.
Given the data below, which room will Ajit stay in?

Names Student Seniority Current room Room preference


list
Amar 1 P R,S,Q
Akbar 2 None R,S
Anthony 3 Q P
Ajit 4 S Q,P,R
(A) P (B) Q (C) R (D) S
Key: (B)
Exp: Amar R
Akbar S
Anthony P
Ajit Q
As per their preferences given.

7. The bar graph below shows the output of five carpenters over one month, each of home made
different items of furniture: Chairs, tables, and beds.

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

20 Bed
18 Table
16 Chair

Number of furniture items


14
12
10
8
6
4 C1 C2 C3 C4 C5
2
0
Carpenter ( C)
Consider the following statements.
(i) The number of beds made by carpenter C2 is exactly the same as the same as the number
of tables made by carpenter C3.
(ii) The total number of chairs made by all carpenters is less than the total number of tables.
Which one of the following is true?
(A) Only i (B) Only ii
(C) Both i and ii (D) Neither i nor ii
Key: (C)
Exp: (i) The number of beds made by carpenter C2 is exactly the same as the number of tables
made by carpenter C3
i.e., beds made by carpenter C 2 = 8 = tables made by carpenter C3 [ From the bar graph ]
So,(i) is correct.
(ii) Total Number of tables made by all carpenters=31.
Total Number of chairs made by all carpenters=23
23 < 31
(ii) is correct
8. The last digit of (2171)7 + (2172)9 + (2173)11 + (2174)13 is
(A) 2 (B) 4 (C) 6 (D) 8
Key: (B)
Exp: The last digit of (2171)7 = 1
The last digit of (2172)9 = (2172)8 (2172) = (2172)4n (2172) [ Where, n = 2]
= 6 2 = 12 ( 2172 ) = Last digit = 6
4n

4n
Last digit of (2172) = 6

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

The last digit of (2173)11 = (2173)8 (2173)3


= (2173) 4n (2173)3 [ Where, n = 2]
Last digit of (2173) 4n = 1 = 1 7 = 7
The last digit of (2174)13 = (2174)12 (2174)
= (2174)2n (2174) [ n = 6]
= 6 4 ( 2174 ) = last digit = 6
2n

Last digit of (2174) 2n = 6 = 24
The last digit of (2171)7 + (2172)9 + (2173)11 + (2174)13
= 1 + 2 + 7 + 4 = 14

9. Two machines M1 and M2 are able to execute any of four jobs P, Q, R and S. The machines
can perform one job on one object at a time. Jobs P, Q, R and S take 30 minutes, 20 minutes,
60 minutes and 15 minutes each respectively. There are 10 objects each requiring exactly 1
job. Job P is to be performed on 2 objects. Job Q on 3 objects. Job R on 1 object and Job S on
4 objects. What is the minimum time needed to complete all the jobs?
(A) 2 hours (B) 2.5 hours (C) 3 hours (D) 3.5 hours
Key: (A)
Exp:

M1 M2
60 R S 15min R takes 60 min s;
30 P S 15min Stakes15mins;
30 P S 15min Q takes 20 min;
S 15min P takes30 min;
Q 20 min
Q 20 min
Q 20 min
2hrs 2hrs

2hrs

(OR)
P 30 min 2 = 60 min
Q 20 min 3 = 60 min
R 60 min 1 = 60 min
S 15min 4 = 60 min
M1 P Q = 2hrs
M2 R S = 2hrs

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
|CH| GATE-2017 www.gateforum.com

10. The old concert hall was demolished because of fears that the foundation would be affected
by the construction tried to mitigate the impact of pressurized air pockets created by the
excavation of large amounts of soil. But even with these safeguards, it was feared that the soil
below the concert hall would not be stable.
From this, one can infer that
(A) The foundations of old buildings create pressurized air pockets underground, which are
difficult to handle during metro construction.
(B) Metro construction has to be done carefully considering its impact on the foundations of
existing buildings.
(C) Old buildings in an area form an impossible hurdle to metro construction in that area.
(D) Pressurized air can be used to excavate large amounts of soil from underground areas.
Key: (B)

 ICPIntensive Classroom Program  eGATE-Live Internet Based Classes DLP  TarGATE-All India Test Series
 Leaders in GATE Preparations  65+ Centers across India
All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

You might also like