Mallick Gupta Notes PDF

LECTURE NOTES
ON
RCSDD
III B. Tech I semester (JNTUH-R13)
Mr. Gude Ramakrishna

Associate Professor
CIVIL ENGINEERING
INSTITUTE OF AERONAUTICAL ENGINEERING
DUNDIGAL, HYDERABAD - 500 043
Doubly Reinforced Beams
Instructional Objectives:
At the end of this lesson, the student should be able to:
explain the situations when doubly reinforced beams are designed,

name three cases other than doubly reinforced beams where compression
reinforcement is provided,
state the assumptions of analysis and design of doubly reinforced beams,
derive the governing equations of doubly reinforced beams,
calculate the values of fsc from (i) d'/d and (ii) calculating the strain of the
compression reinforcement,
state the minimum and maximum amounts of Asc and Ast in doubly reinforced
beams,
state the two types of numerical problems of doubly reinforced beams,
name the two methods of solving the two types of problems, and
write down the steps of the two methods for each of the two types of problems.
4.8.1 Introduction
Concrete has very good compressive strength and almost negligible tensile
strength. Hence, steel reinforcement is used on the tensile side of concrete. Thus, singly
reinforced beams reinforced on the tensile face are good both in compression and tension.
However, these beams have their respective limiting moments of resistance with
specified width, depth and grades of concrete and steel. The amount of steel
reinforcement needed is known as Ast,lim. Problem will arise, therefore, if such a section is
subjected to bending moment greater than its limiting moment of resistance as a singly
reinforced section.
There are two ways to solve the problem. First, we may increase the depth of the
beam, which may not be feasible in many situations. In those cases, it is possible to
increase both the compressive and tensile forces of the beam by providing steel
reinforcement in compression face and additional reinforcement in tension face of the
beam without increasing the depth (Fig. 4.8.1). The total compressive force of such
beams comprises (i) force due to concrete in compression and (ii) force due to steel in
compression. The tensile force also has two components: (i) the first provided by Ast,lim
which is equal to the compressive force of concrete in compression. The second part is
due to the additional steel in tension - its force will be equal to the compressive force of
steel in compression.
Such reinforced concrete beams having steel reinforcement both on tensile and
compressive faces are known as doubly reinforced beams.
Doubly reinforced beams, therefore, have moment of resistance more than the
singly reinforced beams of the same depth for particular grades of steel and concrete. In
many practical situations, architectural or functional requirements may restrict the overall
depth of the beams. However, other than in doubly reinforced beams compression steel
reinforcement is provided when:
(i) some sections of a continuous beam with moving loads undergo change of
sign of the bending moment which makes compression zone as tension
zone or vice versa.
(ii) the ductility requirement has to be followed.
(iii) the reduction of long term deflection is needed.
It may be noted that even in so called singly reinforced beams there would be
longitudinal hanger bars in compression zone for locating and fixing stirrups.
4.8.2 Assumptions
(i) The assumptions of sec. 3.4.2 of Lesson 4 are also applicable here.
(ii) Provision of compression steel ensures ductile failure and hence, the
limitations of x/d ratios need not be strictly followed here.
(iii) The stress-strain relationship of steel in compression is the same as that in
tension. So, the yield stress of steel in compression is 0.87 fy.
4.8.3 Basic Principle
As mentioned in sec. 4.8.1, the moment of resistance Mu of the doubly reinforced

beam consists of (i) Mu,lim of singly reinforced beam and (ii) Mu2 because of equal and
opposite compression and tension forces (C2 and T2) due to additional steel reinforcement
on compression and tension faces of the beam
(Figs. 4.8.1 and 2). Thus, the moment of resistance Mu of a doubly reinforced beam is
Mu = Mu,lim + Mu2 (4.1)
The Mu,lim is as given in Eq. 3.24 of Lesson 5, i.e.,

x x
u u
Mu,li ,max ,max
m = 0.36 ( ) (1 0.42 ) b d 2 fck (4.2)
d d
Also, Mu,lim can be written from Eq. 3.22 of Lesson 5, using xu = xu, max, i.e.,
Mu, lim= 0.87 Ast, lim fy (d - 0.42 xu, max)

x
u,
max
= 0.87pt, lim (1 - 0.42 )bd2 fy (4.3)
d
The additional moment Mu2 can be expressed in two ways (Fig. 4.8.2): considering (i) the
compressive force C2 due to compression steel and (ii) the tensile force T2 due to
additional steel on tension face. In both the equations, the lever arm is (d - d'). Thus, we
have
M A
u2 = sc ( f sc fcc ) (d d ') (4.4)
A
st
M
u2 = 2 ( 0.87f y ) (d d ') (4.5)
where Asc = area of compression steel reinforcement
fsc = stress in compression steel reinforcement
fcc =compressivestressinconcreteatthelevelofcentroidof
compression steel reinforcement
Ast2 = area of additional steel reinforcement

Since the additional compressive force C2 is equal to the additional tensile force T2, we
have
Asc (fsc - fcc) = Ast2 (0.87 fy)
(4.6)
Any two of the three equations (Eqs. 4.4 - 4.6) can be employed to determine Asc and Ast2.
The total tensile reinforcement Ast is then obtained from:
A =A +A
st st 1 st 2 (4.7)
M
p bd u , lim
t,
whereAst1= lim 100 = 0.87f y(d 0.42 xu , max ) (4.8)
4.8.4 Determination of fsc and fcc
It is seen that the values of fsc and fcc should be known before calculating Asc. The
following procedure may be followed to determine the value of fsc and fcc for the design
type of problems (and not for analysing a given section). For
the design problem the depth of the neutral axis may be taken as xu,max as shown in Fig.
4.8.2. From Fig. 4.8.2, the strain at the level of compression steel
reinforcement sc may be written as
d'
sc=0.0035 (1 ) (4.9)
x
u,
max
The stress in compression steel fsc is corresponding to the strain sc of Eq. 4.9 and is
determined for (a) mild steel and (b) cold worked bars Fe 415 and 500 as given below:
(a) Mild steel Fe 250

The strain at the design yield stress of 217.39 N/mm2 (fd = 0.87 fy ) is
0.0010869 (= 217.39/Es). The fsc is determined from the idealized stress-strain diagram of
mild steel (Fig. 1.2.3 of Lesson 2 or Fig. 23B of IS 456) after computing the value of sc
from Eq. 4.9 as follows:
(i) If the computed value of sc 0.0010869, fsc = sc Es = 2 (105) sc
(ii) If the computed value of sc > 0.0010869, fsc = 217.39 N/mm2.
(b) Cold worked bars Fe 415 and Fe 500
The stress-strain diagram of these bars is given in Fig. 1.2.4 of Lesson 2 and in
Fig. 23A of IS 456. It shows that stress is proportional to strain up to a stress of 0.8 fy.
The stress-strain curve for the design purpose is obtained by
substituting fyd for fy in the figure up to 0.8 fyd. Thereafter, from 0.8 fyd to fyd, Table A of
SP-16 gives the values of total strains and design stresses for Fe 415
and Fe 500. Table 4.1 presents these values as a ready reference here.
Table 4.1Values offsc andsc
Stress level Fe 415 Fe 500
Strain sc Stressfsc Strainsc Stressfsc

(N/mm2) (N/mm2)
0.80 fyd 0.00144 288.7 0.00174 347.8
0.85 fyd 0.00163 306.7 0.00195 369.6
0.90 fyd 0.00192 324.8 0.00226 391.3
0.95 fyd 0.00241 342.8 0.00277 413.0
0.975 fyd 0.00276 351.8 0.00312 423.9
1.0 fyd 0.00380 360.9 0.00417 434.8
Linear interpolation may be done for intermediate values.
The above procedure has been much simplified for the cold worked bars by presenting
the values of fsc of compression steel in doubly reinforced beams for different values of
d'/d only taking the practical aspects into consideration. In most of the doubly reinforced
beams, d'/d has been found to be between 0.05 and 0.2. Accordingly, values of fsc can be
computed from Table 4.1 after determining the value of sc from Eq. 4.9 for known values
of d'/d as 0.05, 0.10, 0.15 and 0.2. Table F of SP-16 presents these values of fsc for four
values of d'/d (0.05, 0.10, 0.15 and 0.2) of Fe 415 and Fe 500. Table 4.2 below, however,
includes Fe 250 also whose fsc values are computed as laid down in sec.
4.8.4(a) (i) and (ii) along with those of Fe 415 and Fe 500. This table is very
useful and easy to determine the fsc from the given value of d'/d. The table also
includes strain values at yield which are explained below:
(i)The strain at yield of Fe 250=
Design YieldStress 250
= = 0.0010869
Es 1.15 (200000)
Here, there is only elastic component of the strain without any inelastic strain.
Design YieldStress
(ii)The strain at yield of Fe 415 = Inelastic Strain+
Es
415
= 0.002+ 1.15 (200000) = 0.0038043
500
(iii) The strain at yield of Fe 500 = 0.002+ 1.15 (200000) = 0.0041739

Table 4.2 Values offsc for different values ofd'/d
fy d'/d Strain at
(N/mm2) 0.05 0.10 0.15 0.20 yield

250 217.4 217.4 217.4 217.4 0.0010869
415 355 353 342 329 0.0038043
500 412 412 395 370 0.0041739
4.8.5 Minimum and maximum steel
4.8.5.1 in compression
There is no stipulation in IS 456 regarding the minimum compression steel in

doubly reinforced beams. However, hangers and other bars provided up to 0.2% of the
whole area of cross section may be necessary for creep and shrinkage of concrete.
Accordingly, these bars are not considered as compression reinforcement. From the
practical aspects of consideration, therefore, the minimum steel as compression
reinforcement should be at least 0.4% of the area of concrete in compression or 0.2% of
the whole cross -sectional area of the beam so that the doubly reinforced beam can take
care of the extra loads in addition to resisting the effects of creep and shrinkage of
concrete.
The maximum compression steel shall not exceed 4 per cent of the whole area of
cross-section of the beam as given in cl. 26.5.1.2 of IS 456.
4.8.5.2 in tension
As stipulated in cl. 26.5.1.1(a) and (b) of IS 456, the minimum amount of tensile
reinforcement shall be at least (0.85 bd/fy) and the maximum area of tension
reinforcement shall not exceed (0.04 bD).
It has been discussed in sec. 3.6.2.3 of Lesson 6 that the singly reinforced
beams shall have Ast normally not exceeding 75 to 80% of Ast,lim so that xu remains less
than xu,max with a view to ensuring ductile failure. However, in the
case of doubly reinforced beams, the ductile failure is ensured with the presence of
compression steel. Thus, the depth of the neutral axis may be taken as xu, max if the beam
is over-reinforced. Accordingly, the Ast1 part of tension steel can go
up to Ast, lim and the additional tension steel Ast2 is provided for the additional moment M u
- Mu, lim. The quantities of Ast1 and Ast2 together form the total Ast, which shall not exceed
0.04 bD.
4.8.6 Types of problems and steps of solution
Similar to the singly reinforced beams, the doubly reinforced beams have two
types of problems: (i) design type and (ii) analysis type. The different steps of solutions
of these problems are taken up separately.
4.8.6.1 Design type of problems
In the design type of problems, the given data are b, d, D, grades of concrete and
steel. The designer has to determine Asc and Ast of the beam from the given factored
moment. These problems can be solved by two ways: (i) use of the equations developed
for the doubly reinforced beams, named here as direct computation method, (ii) use of
charts and tables of SP-16.
(a) Direct computation method

Step 1: To determine Mu, lim and Ast, lim from Eqs. 4.2 and 4.8, respectively.
Step 2: To determine Mu2, Asc, Ast2 and Ast from Eqs. 4.1, 4.4, 4.6 and
4.7, respectively.
Step 3: To check for minimum and maximum reinforcement in compression and

tension as explained in sec. 4.8.5.
Step 4: To select the number and diameter of bars from known values of
Asc and Ast.
(b) Use of SP table

Tables 45 to 56 present the pt and pc of doubly reinforced sections for d'/d = 0.05,
0.10, 0.15 and 0.2 for different fck and fy values against Mu /bd2. The values of pt and pc
are obtained directly selecting the proper table with known values of Mu/bd2 and d'/d.
4.8.6.2 Analysis type of problems
In the analysis type of problems, the data given are b, d, d', D, fck, fy, Asc and Ast .
It is required to determine the moment of resistance Mu of such beams.
These problems can be solved: (i) by direct computation method and (ii) by using tables
of SP-16.
(a) Direct computation method
Step 1: To check if the beam is under-reinforced or over-reinforced.

First, xu,max is determined assuming it has reached limiting stage using
x
u,ma
x
coefficients as given in cl. 38.1, Note of IS 456. The strain of tensile steel
d
c (d - xu, max )
st is computed from st = and is checked if st has reached the
x
u,max
yield strain of steel:
fy
=
stat yield + 0.002
1.15 (E)
The beam is under-reinforced or over-reinforced if st is less than or more than the yield
strain.
Step 2: To determine Mu,lim from Eq. 4.2 and Ast,lim from the pt, lim given in Table
3.1 of Lesson 5.
Step 3: To determine Ast2 and Asc from Eqs. 4.7 and 4.6, respectively.
Step 4: To determine Mu2 and Mu from Eqs. 4.4 and 4.1, respectively.
(b) Use of tables of SP-16
As mentioned earlier Tables 45 to 56 are needed for the doubly reinforced beams.
First, the needed parameters d'/d, pt and pc are calculated. Thereafter, Mu/bd2 is computed
in two stages: first, using d'/d and pt and then using d'/d and pc . The lower value of Mu is
the moment of resistance of the beam.
4.8.7 Practice Questions and Problems with Answers
Q.1: When do we go for doubly reinforced beams ?
A.1: The depth of the beams may be restricted for architectural and/or functional
requirements. Doubly reinforced beams are designed if such beams of restricted
depth are required to resist moment more that its Mu,
lim.
Q.2: Name three situations other than doubly reinforced beams, where the compression
reinforcement is provided.
A.2: Compression reinforcement is provided when:
(i) Some sections of a continuous beam with moving loads undergo change of
zone,
(ii) the ductility requirement has to be satisfied,
Q.3: State the assumptions of the analysis and design of doubly reinforced beams.
A.3: See sec. 4.8.2 (i), (ii) and (iii).
Q.4: Derive the governing equations of a doubly reinforced beam.
A.4: See sec. 4.8.3

Q.5: How do you determine fsc of mild steel and cold worked bars and fcc?
A.5: See sec. 4.8.4

Q.6: State the minimum and maximum amounts of Asc and Ast in doubly reinforced
beams.
A.6: See sec. 4.8.5
Q.7: State the two types of problems of doubly reinforced beams specifying the given
data and the values to be determined in the two types of problems.
A.7: The two types of problems are:
(i) Design type ofproblems and

(ii) Analysis type of problems
(i) Design type of problems:

The given data are b, d, D, fck, fy and Mu . It is required to determine Asc and Ast.
(ii) Analysis type of problems:

The given data are b, d, D, fck, fy, Asc and Ast. It is required to determine the Mu of
the beam.
Q.8: Name the two methods of solving the two types of problems.
A.8: The two methods of solving the two types of problems are:
(i) Direct computation method, and

(ii) Use of tables of SP-16.
Q.9: Write down the steps of the solution by the two methods of each of the two types
of problems.
A.9: (A) For the design type of problems:
(i) See sec. 4.8.6.1(a) for the steps of direct computation method, and
(ii) See sec. 4.8.6.1(b) for the steps ofusing the tables of SP-16
(B) For the analysis type of problems:
(i) See sec. 4.8.6.2 (a) for the steps of direct computation method, and
(ii) See sec. 4.8.6.2 (b) for the steps of using the tables of SP-16.
4.8.8 References
1. ReinforcedConcreteLimitStateDesign,6thEdition,byAshokK.Jain,
Nem Chand & Bros, Roorkee, 2002.
2. Limit State Design of Reinforced Concrete, 2nd Edition, by P.C.Varghese,
Prentice-Hall of India Pvt. Ltd., New Delhi, 2002.
3. Advanced Reinforced Concrete Design, by P.C.Varghese, Prentice-Hall of India
Pvt. Ltd., New Delhi, 2001.
4. ReinforcedConcreteDesign,2ndEdition,byS.UnnikrishnaPillaiand
Devdas Menon, Tata McGraw-Hill Publishing Company Limited, New Delhi,
2003.
5. Limit State Design of Reinforced Concrete Structures, by P.Dayaratnam, Oxford
& I.B.H. Publishing Company Pvt. Ltd., New Delhi, 2004.
6. ReinforcedConcreteDesign,1stRevisedEdition,byS.N.Sinha,Tata
McGraw-Hill Publishing Company. New Delhi, 1990.
7. Reinforced Concrete, 6th Edition, by S.K.Mallick and A.P.Gupta, Oxford & IBH
Publishing Co. Pvt. Ltd. New Delhi, 1996.
8. Behaviour, Analysis & Design of Reinforced Concrete Structural Elements, by
I.C.Syal and R.K.Ummat, A.H.Wheeler & Co. Ltd., Allahabad, 1989.
9. Reinforced Concrete Structures, 3rd Edition, by I.C.Syal and A.K.Goel,
A.H.Wheeler & Co. Ltd., Allahabad, 1992.
10. Textbook of R.C.C, by G.S.Birdie and J.S.Birdie, Wiley Eastern Limited, New
Delhi, 1993.
11. Design of Concrete Structures, 13th Edition, by Arthur H. Nilson, David Darwin
and Charles W. Dolan, Tata McGraw-Hill Publishing Company Limited, New
Delhi, 2004.
12. Concrete Technology, by A.M.Neville and J.J.Brooks, ELBS with Longman,
1994.
13. PropertiesofConcrete,4thEdition,1stIndianreprint,byA.M.Neville,
Longman, 2000.
14. Reinforced Concrete Designers Handbook, 10th Edition, by C.E.Reynolds and
J.C.Steedman, E & FN SPON, London, 1997.
15. IndianStandardPlainandReinforcedConcreteCodeofPractice(4th
Revision), IS 456: 2000, BIS, New Delhi.
16. Design Aids for Reinforced Concrete to IS: 456 1978, BIS, New Delhi.
4.8.9 Test 8 with Solutions
Maximum Marks = 50, Maximum Time = 30 minutes
Answer all questions.
TQ.1: Derive the governing equations of a doubly reinforced beam.

(10 marks)
A.TQ.1: See sec. 4.8.3
TQ.2: State the two types of problems of doubly reinforced beams specifying the given
data and the values to be determined in the two type of problems.
(8 marks)
A.TQ.2: The two types of problems are:
(i) Design type ofproblems and

(ii) Analysis type of problems
(i) Design type of problems:

The given data are b, d, D, fck, fy and Mu . It is required to determine Asc and Ast.
(ii) Analysis type of problems:

The given data are b, d, D, fck, fy, Asc and Ast. It is required to determine the Mu of
the beam.
TQ.3: Write down the steps of the solution by the two methods of each of the two
types of problems.
(8 marks)
A.TQ.3: (A) For the design type of problems:
(i) See sec. 4.8.6.1(a) for the steps of direct computation method, and
(ii) See sec. 4.8.6.1(b) for the steps ofusing the tables of SP-16
(B) For the analysis type of problems:
(i) See sec. 4.8.6.2 (a) for the steps of direct computation method, and
(ii) See sec. 4.8.6.2 (b) for the steps of using the tables of SP-16.
TQ.4: How do you determine fsc of mild steel and cold worked bars and fcc?
(8 marks)
A.TQ.4: See sec. 4.8.4
TQ.5: State the assumptions of the analysis and design of doubly reinforced beams.
(8 marks)
A.TQ.5: See sec. 4.8.2 (i), (ii) and (iii).
TQ.6: Name three situations other than doubly reinforced beams, where the compression
reinforcement is provided.
(8 marks)
A.TQ.6: Compression reinforcement is provided when:
(i) Some sections of a continuous beam with moving loads undergo change of
zone,
(ii) the ductility requirement has to be satisfied,
4.8.10 Summary of this Lesson
Lesson 8 derives the governing equations of the doubly reinforced beams

explaining different assumptions and situations when they are needed. The methods of
determination of compressive stress in steel are illustrated. The two types of problems
and the different steps of solution of them by two different methods are explained.
identify the regions where the beam shall be designed as a flanged and where it
will be rectangular in normal slab beam construction,
define the effective and actual widths of flanged beams,
state the requirements so that the slab part is effectively coupled with the flanged
beam,
write the expressions of effective widths of T and L-beams both for continuous
and isolated cases,
derive the expressions of C, T and Mu for four different cases depending on the
location of the neutral axis and depth of the flange.
(iv) Introduction
Reinforced concrete slabs used in floors, roofs and decks are mostly cast
monolithic from the bottom of the beam to the top of the slab. Such rectangular beams
having slab on top are different from others having either no slab (bracings of elevated
tanks, lintels etc.) or having disconnected slabs as in some pre-cast systems (Figs. 5.10.1
a, b and c). Due to monolithic casting, beams and a part of the slab act together. Under
the action of positive bending moment, i.e., between the supports of a continuous beam,
the slab, up to a certain width greater than the width of the beam, forms the top part of the
beam. Such beams having slab on top of the rectangular rib are designated as the flanged
beams - either T or L type depending on whether the slab is on both sides or on one side
of the beam (Figs. 5.10.2 a to e) . Over the supports of a continuous beam, the bending
moment is negative and the slab, therefore, is in tension while a part of the rectangular
beam (rib) is in compression. The continuous beam at support is thus equivalent to a
rectangular beam (Figs. 5.10.2 a, c, f and g).
The actual width of the flange is the spacing of the beam, which is the same as the
distance between the middle points of the adjacent spans of the slab, as shown in Fig.
5.10.2 b. However, in a flanged beam, a part of the width less than the actual width, is
effective to be considered as a part of the beam. This width of the slab is designated as
the effective width of the flange.
5.10.2 Effective Width

5.10.2.1 IS code requirements
The following requirements (cl. 23.1.1 of IS 456) are to be satisfied to ensure the
combined action of the part of the slab and the rib (rectangular part of the beam).
4.8.3 The slab and the rectangular beam shall be cast integrally or they shall be
effectively bonded in any other manner.
4.8.4 Slabs must be provided with the transverse reinforcement of at least 60 per cent of
the main reinforcement at the mid span of the slab if the main reinforcement of the slab is
parallel to the transverse beam (Figs. 5.10.3 a and b).
The variation of compressive stress (Fig. 5.10.4) along the actual width of the
flange shows that the compressive stress is more in the flange just above the rib than the
same at some distance away from it. The nature of variation is complex and, therefore,
the concept of effective width has been introduced. The effective width is a convenient
hypothetical width of the flange over which the compressive stress is assumed to be
uniform to give the same compressive
force as it would have been in case of the actual width with the true variation of
compressive stress.
5.10.2.2 IS code specifications
Clause 23.1.2 of IS 456 specifies the following effective widths of T and

L-beams:
(a) For T-beams, the lesser of

(i) bf = lo/6 + bw + 6 Df
(iv) bf=Actual width of the flange
4.8.4 For isolated T-beams, the lesser of
lo
(i)bf = + bw
(lo /b) + 4
bf=Actual width of the flange
(iv) ForL-beams, the lesser of

(i) bf = lo/12 + bw + 3 Df
bf=Actual width of the flange
(iii)For isolated L-beams, the lesser of
0.5 lo
(i)bf = + bw
(lo /b) + 4
(ii) bf = Actual width of the flange
where bf = effective width of the flange,
lo = distance between points of zero moments in the beam, which is the effective
span for simply supported beams and 0.7 times the effective span for
continuous beams and frames,
bw = beadth of the web,
Df = thickness of the flange,
and b = actual width of the flange.

5.10.3 Four Different Cases
The neutral axis of a flanged beam may be either in the flange or in the web
depending on the physical dimensions of the effective width of flange bf, effective width
of web bw, thickness of flange Df and effective depth of flanged beam d (Fig. 5.10.4). The
flanged beam may be considered as a rectangular beam of width bf and effective depth d
if the neutral axis is in the flange as the concrete in tension is ignored. However, if the
neutral axis is in the web, the compression is taken by the flange and a part of the web.
All the assumptions made in sec. 3.4.2 of Lesson 4 are also applicable for the
flanged beams. As explained in Lesson 4, the compressive stress remains constant
between the strains of 0.002 and 0.0035. It is important to find the depth h of the beam
where the strain is 0.002 (Fig. 5.10.5 b). If it is located in the web, the whole of flange
will be under the constant stress level of 0.446 fck. The
following gives the relation of Df and d to facilitate the determination of the depth h
where the strain will be 0.002.
From the strain diagram of Fig. 5.10.5 b:
0.002 xu- h
=
0.0035 xu
h 3
or = = 0.43
x 7
u
(5.1)
when xu= xu , max , we get
3
h= xu , max= 0.227 d , 0.205 d and 0.197 d , for Fe250,Fe415andFe
7
500, respectively. In general, we can adopt, say
h/d = 0.2 (5.2)
The same relation is obtained below from the values of strains of concrete and steel of
Fig. 5.10.5 b.

st d - xu
=
c xu
d st + c
or xu = c (5.3)
Dividing Eq. 5.1 by Eq. 5.3
h 0.0015
= (5.4)
d st + 0.0035
Using st = (0.87f y/ Es)+ 0.002 in Eq. 5.4, we get h/d = 0.227, 0.205 and
0.197 for Fe 250, Fe 415 and Fe 500 respectively, and we can adopt h/d = 0.2
(as in Eq. 5.2).
Thus, we get the same Eq. 5.2 from Eq. 5.4,
h/d= 0.2 (5.2)

It is now clear that the three values of h are around 0.2 d for the three grades of
steel. The maximum value of h may be Df, at the bottom of the flange where the strain
will be 0.002, if Df /d = 0.2. This reveals that the thickness of the flange may be
considered small if Df /d does not exceed 0.2 and in that case, the position of the fibre of
0.002 strain will be in the web and the entire flange will be under a constant compressive
stress of 0.446 fck .
On the other hand, if Df is > 0.2 d, the position of the fibre of 0.002 strain will be
in the flange. In that case, a part of the slab will have the constant stress of 0.446 fck
where the strain will be more than 0.002.
Thus, in the balanced and over-reinforced flanged beams (when xu = xu , max ), the
ratio of Df /d is important to determine if the rectangular stress block is for the full depth
of the flange (when Df /d does not exceed 0.2) of for a part of the flange (when Df /d >
0.2). Similarly, for the under-reinforced flanged beams, the ratio of Df /xu is considered in
place of Df /d. If Df /xu does not exceed
0.43 (see Eq. 5.1), the constant stress block is for the full depth of the flange. If Df /xu >
0.43, the constant stress block is for a part of the depth of the flange.
Based on the above discussion, the four cases of flanged beams are as follows:
(iii) Neutral axis is in the flange (xu < Df ), (Fig. 5.10.6 a to c)
14. Neutral axis is in the web and the section is balanced (xu = xu,max > Df),
(Figs. 5.10.7 and 8 a to e)
It has two situations: (a) when Df /d does not exceed 0.2, the constant
stress block is for the entire depth of the flange (Fig. 5.10.7), and
(b) when Df /d > 0.2, the constant stress block is for a part of the depth of flange
(Fig. 5.10.8).
17. Neutral axis is in the web and the section is under-reinforced (xu,max > xu >
Df), (Figs. 5.10.9 and 10 a to e)
This has two situations: (a) when Df /xu does not exceed 0.43, the full
depth of flange is having the constant stress (Fig. 5.10.9), and (b) when Df /xu >
0.43, the constant stress is for a part of the depth of flange
(Fig. 5.10.10).
(iii) Neutral axis is in the web and the section is over-reinforced (xu > xu,max>
Df), (Figs. 5.10.7 and 8 a to e)
As mentioned earlier, the value of xu is then taken as xu,max when xu> xu,max.
Therefore, this case also will have two situations depending on Df /d not
exceeding 0.2 or > 0.2 as in (ii) above. The governing equations of the four
different cases are now taken up.
5.10.4 Governing Equations
The following equations are only for the singly reinforced T-beams.
Additional terms involving Mu,lim, Mu2, Asc , Ast1 and Ast2 are to be included from Eqs. 4.1
to 4.8 of sec. 4.8.3 of Lesson 8 depending on the particular case.
Applications of these terms are explained through the solutions of numerical problems of
doubly reinforced T-beams in Lessons 11 and 12.
5.10.4.1 Case (i): When the neutral axis is in the flange (xu < Df ), (Figs. 5.10.6 a to c)
Concrete below the neutral axis is in tension and is ignored. The steel
reinforcement takes the tensile force (Fig. 5.10.6). Therefore, T and L-beams are
considered as rectangular beams of width bf and effective depth d. All the equations of
singly and doubly reinforced rectangular beams derived in Lessons 4 to 5 and 8
respectively, are also applicable here.
5.10.4.2 Case (ii): When the neutral axis is in the web and the section is balanced
(xu,max > Df ), (Figs. 5.10.7 and 8 a to e)
(a) When Df /d does not exceed 0.2, (Figs. 5.10.7 a to e)
As explained in sec. 5.10.3, the depth of the rectangular portion of the stress block
(of constant stress = 0.446 fck) in this case is greater than Df (Figs. 5.10.7 a, b and c). The
section is split into two parts: (i) rectangular web of width bw and effective depth d, and
(ii) flange of width (bf - bw) and depth Df (Figs.
5.10.7 d and e).
Total compressive force = Compressive force of rectangular beam of width bw and depth
d + Compressive force of rectangular flange of width (bf - bw) and depth Df .
Thus, total compressive force

C=0.36 fckbwxu, max+0.45fck (bf - bw) Df (5.5)
(Assuming the constant stress of concrete in the flange as0.45 fck in place of
0.446 fck ,as per G-2.2 of IS 456), and the tensile force
T=0.87fyAst (5.6)
The lever arm of the rectangular beam (web part) is (d - 0.42 xu, max) and the same for the
flanged part is (d - 0.5 Df ).
So, the total moment = Moment due to rectangular web part + Moment due to rectangular
flange part
or Mu = 0.36fck bw xu, max (d - 0.42 xu, max ) + 0.45fck (bf - bw) Df (d - Df /2)
or Mu = 0.36(xu, max /d){1 - 0.42( xu, max/d)} fck bw d2 + 0.45fck(bf - bw) Df(d - Df
/2)
(5.7)
Equation 5.7 is given in G-2.2 of IS 456.
(b) When Df /d > 0.2, (Figs. 5.10.8 a to e)
In this case, the depth of rectangular portion of stress block is within the flange
(Figs. 5.10.8 a, b and c). It is assumed that this depth of constant stress
(0.45 fck) is yf, where
yf = 0.15 xu, max + 0.65 Df, but not greater than Df
(5.8)
The above expression of yf is derived in sec. 5.10.4.5.
As in the previous case (ii a), when Df /d does not exceed 0.2, equations of C, T
and M u are obtained from Eqs. 5.5, 6 and 7 by changing Df to yf. Thus, we have (Figs.
5.10.8 d and e)
C = 0.36 fck bw xu, max + 0.45 fck (bf - bw) yf (5.9)
T = 0.87 fy Ast
(5.10)
The lever arm of the rectangular beam (web part) is (d - 0.42 xu, max same for
the flange part is (d - 0.5 yf ). Accordingly, the expression of follows: ) and the
Mu is as
Mu = 0.36(xu, max /d){1 - 0.42( xu, max/d)} fck bw d2 + 0.45 fck(bf - bw) yf(d - yf
/2)
(5.11)
5.10.4.3 Case (iii): When the neutral axis is in the web and the section is under-
reinforced (xu > Df ), (Figs. 5.10.9 and 10 a to e)
(a) When Df / xu does not exceed 0.43, (Figs. 5.10.9 a to e)
Since Df does not exceed 0.43 xu and h (depth of fibre where the strain is 0.002) is
at a depth of 0.43 xu, the entire flange will be under a constant stress of 0.45 fck (Figs.
5.10.9 a, b and c). The equations of C, T and Mu can be written in the same manner as in
sec. 5.10.4.2, case (ii a). The final forms of the equations are obtained from Eqs. 5.5, 6
and 7 by replacing xu, max by xu. Thus, we have (Figs. 5.10.9 d and e)
C = 0.36 fck bw xu + 0.45 fck (bf - bw) Df
(5.12)
T = 0.87 fy Ast
(5.13)
Mu = 0.36(xu /d){1 - 0.42( xu /d)} fck bw d2 + 0.45 fck(bf - bw) Df (d - Df /2)
(5.14)
(b) When Df / xu > 0.43, (Figs. 5.10.10 a to e)
Since Df > 0.43 xu and h (depth of fibre where the strain is 0.002) is at a depth of
0.43 xu, the part of the flange having the constant stress of 0.45 fck is assumed as yf (Fig.
5.10.10 a, b and c). The expressions of yf , C, T and Mu can be written from Eqs. 5.8, 9,
10 and 11 of sec. 5.10.4.2, case (ii b), by replacing xu,max by xu. Thus, we have (Fig.
5.10.10 d and e)
yf = 0.15 xu + 0.65 Df, but not greater than Df
(5.15)
C = 0.36 fck bw xu + 0.45 fck (bf - bw) yf
(5.16)
T = 0.87 fy Ast
(5.17)
Mu = 0.36(xu /d){1 - 0.42( xu /d)} fck bw d2 + 0.45 fck(bf - bw) yf (d - yf /2)
(5.18)
5.10.4.4 Case (iv): When the neutral axis is in the web and the section is over-
reinforced (xu > Df ), (Figs. 5.10.7 and 8 a to e)
For the over-reinforced beam, the depth of neutral axis xuis more than
xu, maxas in rectangular beams. However, xu is restricted up to xu,max. Therefore,
the corresponding expressions of C, Tand Mu for the two situations (a) when
Df / d does not exceed 0.2and (b) when Df / d > 0.2are written from Eqs. 5.5
to 5.7 and 5.9 to 5.11, respectively of sec. 5.10.4.2 (Figs. 5.10.7 and 8). The expression of
yf for (b) is the same as that of Eq. 5.8.
(a) When Df /d does not exceed 0.2 (Figs. 5.10.7 a to e)
The equations are:
C= 0.36 fckbwxu, max + 0.45fck (bf - bw) Df (5.5)
T=0.87fyAst (5.6)
Mu = 0.36(xu, max /d){1 - 0.42( xu, max/d)} fck bw d2 + 0.45 fck(bf - bw) Df(d - Df
/2)
(5.7)
(b)When Df /d>0.2 (Figs. 5.10.8 a to e)
yf = 0.15 xu, max + 0.65 Df, but not greater thanDf

(5.8)
C = 0.36 fckbwxu, max + 0.45fck (bf - bw) yf (5.9)
T=0.87fyAst
(5.10)
Mu = 0.36(xu, max /d){1 - 0.42( xu, max/d)} fck bw d2 + 0.45 fck(bf - bw) yf(d - yf
/2)
(5.11)
It is clear from the above that the over-reinforced beam will not have additional
moment of resistance beyond that of the balanced one. Moreover, it will prevent steel
failure. It is, therefore, recommended either to re-design or to go for doubly reinforced
flanged beam than designing over-reinforced flanged beam.
5.10.4.5 Derivation of the equation to determine yf , Eq. 5.8, Fig. 5.10.11
Whitney's stress block has been considered to derive Eq. 5.8. Figure
5.10.11 shows the two stress blocks of IS code and of Whitney.
yf = Depth of constant portion of the stress block when Df /d > 0.2. As yf is a
function of xu and Df and let us assume
yf = A xu + B Df
(5.19)
where A and B are to be determined from the following two conditions:
(i)yf=0.43xu , when Df = 0.43xu

(5.20)
(ii)yf=0.8 xu , when Df = xu
(5.21)
Using the conditions of Eqs. 5.20 and 21 in Eq. 5.19, we get A = 0.15 and B = 0.65. Thus,
we have
yf = 0.15 xu + 0.65 Df
(5.8)
Q.1: Why do we consider most of the beams as T or L-beams between the supports and
rectangular beams over the support of continuous span?
A.1: Sec. 5.10.1, first paragraph.
Q.2: Draw cross-section of a beam with top slab and show the actual width and
effective width of the T-beam.
A.2: Fig. 5.10.2 b.
Q.3: State the requirements with figures as per IS 456 which ensure the combined
action of the part of the slab and the rib of flanged beams.
A.3: Sec. 5.10.2.1(a) and (b), Figure 5.10.3 (a and b).
Q.4: Define effective width of flanged beams.
A.4: Effective width is an imaginary width of the flange over which the compressive
stress is assumed to be uniform to give the same compressive force as it would
have been in case of the actual width with the true variation of compressive stress
(Fig. 5.10.4 of text).
Q.5: Write the expressions of effective widths of T and L-beams and isolated beams.
A.5: Sec. 5.10.2.2.
Q.6: Name the four different cases of flanged beams.
A.6: The four different cases are:

(iii) Whentheneutralaxisisintheflange(xu<Df)(discussedinsec.
5.10.4.1).
(iv) When the neutral axis is in the web and the section is balanced (xu,max > Df). It
has two situations: (a) when Df /d does not exceed 0.2 and (b)
when Df /d > 0.2 (discussed in sec. 5.10.4.2).
(iii) When the neutral axis is in the web and the section is under-reinforced (xu,max
> xu > Df). It has two situations: (a) when Df /xu does not exceed
and (b) whenDf /xu > 0.43 (discussed in sec. 5.10.4.3).
(iv) When the neutral axis is in the web and the section is over-reinforced (xu >
xu,max> Df). It has two situations: (a) when Df /d does not exceed
and (b) whenDf /d > 0.2 (discussed in sec. 5.10.4.4).
Q.7: (a) Derive the following equation:

yf = 0.15 xu,max + 0.65 Df
(b) State when this equation is to be used.
(c) What is the limiting value ofyf ?
A.7: (a) For derivation of the equation, see sec. 5.10.4.5.
(b) This equation gives the depth of flange over which the stress is constant at
0.45 fck (i.e. strain is more than 0.002) when the neutral axis is in web. This occurs
when Df /d > 0.2 for balanced beam and when Df /xu
> 0.43 for under-reinforced beams.
(c) Limiting value ofyfisDf.
5.10.6 References
1. Reinforced Concrete Limit State Design, 6th Edition, by Ashok K. Jain, Nem
Chand & Bros, Roorkee, 2002.
2. Limit State Design of Reinforced Concrete, 2nd Edition, by P.C.Varghese,
3. Advanced Reinforced Concrete Design, by P.C.Varghese, Prentice-Hall of India
4. Reinforced Concrete Design, 2nd Edition, by S.Unnikrishna Pillai and Devdas
Menon, Tata McGraw-Hill Publishing Company Limited, New
Delhi, 2003.
5. Limit State Design of Reinforced Concrete Structures, by P.Dayaratnam, Oxford
& I.B.H. Publishing Company Pvt. Ltd., New Delhi, 2004.
6. Reinforced Concrete Design, 1st Revised Edition, by S.N.Sinha, Tata McGraw-
Hill Publishing Company. New Delhi, 1990.
7. Reinforced Concrete, 6th Edition, by S.K.Mallick and A.P.Gupta, Oxford &
IBH Publishing Co. Pvt. Ltd. New Delhi, 1996.
8. Behaviour, Analysis & Design of Reinforced Concrete Structural Elements, by
9. ReinforcedConcreteStructures,3rdEdition,byI.C.SyalandA.K.Goel,
10. Textbook of R.C.C, by G.S.Birdie and J.S.Birdie, Wiley Eastern Limited, New
Delhi, 1993.
11. Design of Concrete Structures, 13th Edition, by Arthur H. Nilson, David Darwin
and Charles W. Dolan, Tata McGraw-Hill Publishing Company
Limited, New Delhi, 2004.
12. ConcreteTechnology,byA.M.NevilleandJ.J.Brooks,ELBSwith
Longman, 1994.
Longman, 2000.
Version 2 CE IIT, Kharagpur

15. Indian Standard Plain and Reinforced Concrete Code of Practice (4th Revision),
IS 456: 2000, BIS, New Delhi.
TQ.1: Why do we consider most of the beams as T or L- beams between the supports and
rectangular beams over the support of continuous span?
(5 marks)
A.TQ.1: Sec. 5.10.1, first paragraph.
TQ.2: Define effective width of flanged beams.

(5 marks) A.TQ.2: Effective width is a convenient hypothetical width of the flange over
which the compressive stress is assumed to be uniform to give the same compressive
force as it would have been in case of the actual width with
the true variation of compressive stress (Fig. 5.10.4 of text).
TQ.3: State the requirements with figures as per IS 456 which ensure the combined
action of the part of the slab and the rib of flanged beams.
(10 marks)
A.TQ.3: Sec. 5.10.2.1(a) and (b), Figure 5.10.3 (a and b).
TQ.4: Write the expressions of effective widths of T and L-beams and isolated beams.
(10 marks)
A.TQ.4: Sec. 5.10.2.2.
TQ.5: Name the four different cases of flanged beams.

(10 marks)
A.TQ.5: The four different cases are
(i) Whentheneutralaxisisintheflange(xu<Df)(discussedinsec.
5.10.4.1).
(ii) When the neutral axis is in the web and the section is balanced. It has two
situations: (a) when Df /d does not exceed 0.2 and (b) when Df /d
> 0.2 (discussed in sec. 5.10.4.2).
(iii) When the neutral axis is in the web and the section is under-reinforced. It has two situations: (a) when Df /xu does not exceed
0.43 and (b) when Df /xu > 0.43 (discussed in sec. 5.10.4.3).
(iv) When the neutral axis is in the web and the section is over-reinforced. It has two situations: (a) when Df /d does not exceed
0.2 and (b) when
Df /d > 0.2 (discussed in sec. 5.10.4.4).
TQ.6: (a) Derive the following equation:

yf = 0.15 xu,max + 0.65 Df
(b) State when this equation is to be used.

(c) What is the limiting value ofyf ?
(5 + 3 + 2 = 10 marks) A.TQ.6: (a) For derivation of the equation, see
sec. 5.10.4.5.
(b) This equation gives the depth of flange over which the stress is constant at 0.45 fck (i.e. strain is more than 0.002) when the
neutral axis is in web. This occurs when Df /d > 0.2 for balanced beam and when Df /xu
> 0.43 for under-reinforced beams.
(c) Limiting value ofyfisDf.
This lesson illustrates the practical situations when slabs are cast integrally with the beams to form either T and L-beams or
rectangular beams.
The concept of effective width of the slab to form a part of the beam has been explained. The requirements as per IS 456 have been
illustrated so that the considered part of the slab may become effective as a beam. Expressions of effective widths for different cases of T
and L-beams are given. Four sets of governing equations for determining C, T and Mu are derived for four different cases. These
equations form the basis of analysis and design of singly and doubly reinforced T and L- beams.
DESIGN OF DOUBLY REINFORCED BEAMS

When beam depth is restricted and the moment the beam has to carry is greater than the moment capacity of the beam in concrete
failure.
When B.M at the section can change sign.
When compression steel can substantially improve the ductility of beams and its use is therefore advisable in members when larger
amount of tension steel becomes necessary for its strength.
Compression steel is always used in structures in earthquake regions to increase their ductility.
Compression reinforcement will also aid significantly in reducing the long-term deflections of beams.
(v) A doubly reinforced concrete beam is reinforced in both compression and tension faces.
4.8.5 When depth of beam is restricted, strength available from a singly reinforced beam is inadequate.
4.8.6 At a support of a continuous beam, the bending moment changes sign, such a situation may also arise in design of a ring beam.
2 Analysis of a doubly reinforced section involves determination of moment of resistance with given beam width, depth, area of
tension and compression steels and their covers.
3 In doubly reinforced concrete beams the compressive force consists of two parts; both in concrete and steel in compression.
4 Stress in steel at the limit state of collapse may be equal to yield stress or less depending on position of the neutral axis.
Doubly Reinforced Concrete Beam
Steel Beam Theory
Design Steps
4.8.5 Determine the limiting moment of resistance Mum for the given cross-section using the equation for a singly reinforced beam
Mlim = 0.87fy.Ast,1 [d - 0.42xm] = 0.36 fck.b.xm [d - 0.42xm]
(ii) If the factored moment Mu exceeds Mlim, a doubly reinforced section is required (Mu - Mlim) = Mu2
Additional area of tension steel Ast2 is obtained by considering the equilibrium of force of compression in comp. steel and force of
tension T2 in the additional tension steel
sc Asc cc Asc = 0.87fy Ast2 sc Asc = 0.87 fy Ast2
Asc = compression steel.
cc = Comp. stress in conc at the level of comp. steel = 0.446fck.
Reasons
(v) When beam section is shallow in depth, and the flexural strength obtained using balanced steel is insufficient i.e. the factored
moment is more than the limiting ultimate moment of resistance of the beam section. Additional steel enhances the moment
capacity.
(vi) Steel bars in compression enhances ductility of beam at ultimate strength.
(vii) Compression steel reinforcement reduces deflection as moment of inertia of the beam section also increases.
(viii) Long-term deflections of beam are reduced by compression steel.
(ix) Curvature due to shrinkage of concrete are also reduced.
(x) Doubly reinforced beams are also used in reversal of external loading.
Examples
(iii) A single reinforced rectangular beam is 400mm wide. The effective depth of the beam section is 560mm and its effective cover is
40mm. The steel reinforcement consists of 4 MS 18mm diameter bars in the beam section. The grade of concrete is M20. Locate the
neutral axis of the beam section.
(iv) In example 1, the bending moment at a transverse section of beam is 105 kN-m. Determine the strains at the extreme fibre of
concrete in compression and steel bars provided as reinforcement in tension. Also determine the stress in steel bars.
(v) In example 2, the strain in concrete at the extreme fibre in compression cu is 0.00069 and the tensile stress in bending in steel is
199.55 N/mm2. Determine the depth of neutral axis and the moment of resistance of the beam section.
(vi) Determine the moment of resistance of a section 300mm wide and 450mm deep up to the centre of reinforcement. If it is reinforced
with (i) 4-12mm fe415 grade bars, (ii) 6-18mm fe415 grade bars.
E
x
a
m
p
l
e
s
(iv) A rectangular beam section is 200mm

wide and 400mm deep up to the centre
of reinforcement. Determine the
reinforcement required at the bottom if
it has to resist a factored moment of
40kN-m. Use M20 grade concrete and
fe415 grade steel.
(v) A rectangular beam section is 250mm

wide and 500mm deep up to the centre
of tension steel which consists of 4-
22mm dia. bars. Find the position of the
neutral axis, lever arm, forces of
compression and tension and safe
moment of resistance if concrete is M20
grade and steel is Fe500 grade.
(vi) A rectangular beam is 200mm wide and

450 mm overall depth with an effective
cover of 40mm. Find the reinforcement
required if it has to resist a moment of
35 kN.m. Assume M20 concrete and
Fe250 grade steel.
Limit State of
Serviceability
Instruction Objectives:
explain the need to check for the limit state of serviceability after designing the
structures by limit state of collapse,
differentiate between short- and long-term deflections,
state the influencing factors to both short- and long-term deflections,
select the preliminary dimensions of structures to satisfy the requirements as per

IS 456,
calculate the short- and long-term deflections of designed beams.
7.17.1 Introduction
Structures designed by limit state of collapse are of comparatively smaller

sections than those designed employing working stress method. They, therefore, must be
checked for deflection and width of cracks. Excessive deflection of a structure or part
thereof adversely affects the appearance and efficiency of the structure, finishes or
partitions. Excessive cracking of concrete also seriously affects the appearance and
durability of the structure. Accordingly, cl. 35.1.1 of IS 456 stipulates that the designer
should consider all relevant limit states to ensure an adequate degree of safety and
serviceability. Clause 35.3 of IS 456 refers to the limit state of serviceability comprising
deflection in cl. 35.3.1 and cracking in cl. 35.3.2. Concrete is said to be durable when it
performs satisfactorily in the working environment during its anticipated exposure
conditions during service. Clause 8 of IS 456 refers to the durability aspects of concrete.
Stability of the structure against overturning and sliding (cl. 20 of IS
456), and fire resistance (cl. 21 of IS 456) are some of the other importance issues to be
kept in mind while designing reinforced concrete structures.
This lesson discusses about the different aspects of deflection of beams and the
requirements as per IS 456. In addition, lateral stability of beams is also taken up while
selecting the preliminary dimensions of beams. Other requirements, however, are beyond
the scope of this lesson.
7.17.2 Short- and Long-term Deflections
As evident from the names, short-term deflection refers to the immediate

deflection after casting and application of partial or full service loads, while the long-term
deflection occurs over a long period of time largely due to shrinkage
and creep of the materials. The following factors influence the short-term deflection of
structures:
(vi) magnitude and distribution of live loads,

(vii)span and type of end supports,
(viii) cross-sectional area of the members,
(ix) amount of steel reinforcement and the stress developed in the
reinforcement,
(x) characteristic strengths of concrete and steel, and
(xi) amount and extent of cracking.
The long-term deflection is almost two to three times of the short-term deflection.
The following are the major factors influencing the long-term deflection of the structures.
4.8.7 humidity and temperature ranges during curing,

4.8.8 age of concrete at the time of loading, and
(c) type and size of aggregates, water-cement ratio, amount of compression
reinforcement, size of members etc., which influence the creep and shrinkage
of concrete.
7.17.3 Control of Deflection
Clause 23.2 of IS 456 stipulates the limiting deflections under two heads as given
below:
5 The maximum final deflection should not normally exceed span/250 due to
all loads including the effects of temperatures, creep and shrinkage and measured from
the as-cast level of the supports of floors, roof and all other horizontal members.
6 The maximum deflection should not normally exceed the lesser of span/350
or 20 mm including the effects of temperature, creep and shrinkage occurring after
erection of partitions and the application of finishes.
It is essential that both the requirements are to be fulfilled for every structure.
7.17.4 Selection of Preliminary Dimensions
The two requirements of the deflection are checked after designing the members.
However, the structural design has to be revised if it fails to satisfy any one of the two or
both the requirements. In order to avoid this, IS 456 recommends the guidelines to
assume the initial dimensions of the members which will generally satisfy the deflection
limits. Clause 23.2.1 stipulates different span to effective depth ratios and cl. 23.3
recommends limiting slenderness of
beams, a relation of b and d of the members, to ensure lateral stability. They are given
below:
(A) For the deflection requirements
Different basic values of span to effective depth ratios for three different support
conditions are prescribed for spans up to 10 m, which should be modified under any or all
of the four different situations: (i) for spans above 10 m, (ii) depending on the amount
and the stress of tension steel reinforcement, (iii) depending on the amount of
compression reinforcement, and (iv) for flanged beams. These are furnished in Table 7.1.
(B) For lateral stability
The lateral stability of beams depends upon the slenderness ratio and the support
conditions. Accordingly cl. 23.3 of IS code stipulates the following:
4.8.6 For simply supported and continuous beams, the clear distance between the
lateral restraints shall not exceed the lesser of 60b or 250b2/d, where d is the effective
depth and b is the breadth of the compression face midway between the lateral restraints.
4.8.7 For cantilever beams, the clear distance from the free end of the cantilever to
the lateral restraint shall not exceed the lesser of 25b or 100b2/d.
Table 7.1 Span/depth ratios and modification factors
Sl. Items Cantilever Simply Continuous

No. supported
1 Basic values of span to 7 20 26
effective depth ratio for
spans up to 10 m
2 Modification factors for Not applicable Multiply values of row 1 by
spans > 10 m as deflection 10/span in metres.
calculations
are to be
done.
3 Modification factors Multiply values of row 1 or 2 with the modification
depending on area and factor from Fig.4 of IS 456.
stress of steel
4 Modification factors Further multiply the earlier respective value with
depending as area of that obtained from Fig.5 of IS 456.
compression steel
5 Modification factors for (i)Modify values of row 1 or 2 as per Fig.6 of IS
flanged beams 456.
(ii)Further modify as per row 3 and/or 4 where
reinforcement percentage to be used on area of
section equal to bf d.
7.17.5 Calculation of Short-Term Deflection
Clause C-2 of Annex C of IS 456 prescribes the steps of calculating the short-term
deflection. The code recommends the usual methods for elastic deflections using the
short-term modulus of elasticity of concrete Ec and effective moment of inertia Ieff given
by the following equation:
Ir
I = I I
eff ;butI r eff gr
1. 2 - (M r / M )( z / d )( 1 x / d )( bw / b )
(7.1)
where Ir =moment of inertia of the cracked section,

Mr = cracking moment equal to ( fcr Igr)/yt , where fcr is the modulus of rupture of
concrete, Igr is the moment of inertia of the gross section about the
centroidal axis neglecting the reinforcement, and yt is the distance from
centroidal axis of gross section, neglecting the reinforcement, to extreme
fibre in tension,
M = maximum moment under service loads,
z = lever arm,
x = depth of neutral axis,
d = effective depth,
bw = breadth of web, and
b = breadth of compression face.

For continuous beams, however, the values of Ir, Igr and Mr are to be modified by
the following equation:
X +X
1 2
k
X e= 1 + (1- k1 ) X o
2
(7.2)
where Xe = modified value ofX,
X1, X2 = values of Xat the supports,

Xo = value of Xat mid span,
k1 = coefficient given in Table 25 of IS 456 and in Table 7.2 here, and
X = value of Ir,IgrorMras appropriate.
Table 7.2 Values of coefficientk1
k1 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4
or
less
k2 0 0.03 0.08 0.16 0.30 0.50 0.73 0.91 0.97 1.0
Note: k2 is given by (M1 + M2)/(MF1 + MF2), where M1 and M2 = support

moments, and MF1 and MF2 = fixed end moments.
7.17.6 Deflection due to Shrinkage
Clause C-3 of Annex C of IS 456 prescribes the method of calculating the

deflection due to shrinkage cs from the following equation:
cs = k3 cs l 2
(7.3)
where k3 is a constant which is 0.5 for cantilevers, 0.125 for simply supported
members, 0.086 for members continuous at one end, and 0.063 for fully
continuous members; cs is shrinkage curvature equal to k4 cs /Dwhere cs is
the ultimateshrinkagestrainofconcrete.For cs , cl. 6.2.4.1ofIS 456
recommends an approximate value of 0.0003 in the absence of test data.
k4 = 0.72( pt - pc ) / pt 1.0, for 0.25 pt - pc < 1.0

= 0.65( pt - pc ) / pt 1.0, for pt - pc 1.0
(7.4)
where pt =100Ast/bdand pc=100Asc/bd,D is the total depth of the section,

and lis the length of span.
7.17.7 Deflection Due to Creep
Clause C-4 of Annex C of IS 456 stipulates the following method of calculating

deflection due to creep. The creep deflection due to permanent loads
cc( perm) is obtained from the following equation:
=
cc( 1cc( perm) -

perm) 1(perm)
(7.5)
where
1cc( perm) =initial plus creep deflection due to permanent loads obtained
usinganelasticanalysiswithaneffectivemodulusof
elasticity,
Ece= Ec /(1 + ), being the creep coefficient, and

1(
perm ) = short-term deflection due to permanent loads usingEc.
(iii) Numerical Problems
Problem 1:
Figures 7.17.1 and 2 present the cross-section and the tensile steel of a simply
supported T-beam of 8 m span using M 20 and Fe 415 subjected to dead
load of 9.3 kN/m and imposed loads of 10.7 kN/m at service. Calculate the short-and
long-term deflections and check the requirements of IS 456.
Solution 1:
Step 1: Properties of plain concrete section
Taking moment of the area about the bottom of the beam

yt = (300)(600)(300) + (2234 - 300)(100)(550) = 429.48 mm
(300)(600) + (2234 - 300)(100)
I
300(429.48)3 2234(170.52)3 1934(70.52)3
gr = + - = (11.384) (10)9 mm4
3 3 3
This can also be computed from SP-16 as explained below:

Here, bf /b w = 7.45, Df /D = 0.17. Using these values in chart 88 of SP-16, we get
k1 = 2.10.
Igr = k1bw D3/12 = (2.10)(300)(600)3/12 = (11.384)(10)9 mm4
Step 2: Properties of the cracked section (Fig.7.17.2)
fcr = 0.7 fck (cl. 6.2.2 of IS 456) = 3.13 N/mm2

Mr=fcr Igr /yt =3.13(11.384)(10)9/429.48=82.96kNm
Es=200000N/mm2
Ec=5000 fck(cl. 6.2.3.1 of IS 456)=22360.68N/mm2
m=Es /Ec= 8.94
Taking moment of the compressive concrete and tensile steel about the neutral axis, we
have (Fig.7.17.2)
bf x2/2 =m Ast (d x) gives (2234)(x2/2)=(8.94)(1383)(550 x)
or x2 + 11.07 x 6087.92 =0 .Solving the equation, we getx = 72.68 mm.

z =lever arm=d x/3=525.77 mm
2234(72.68)3
Ir = + 8.94(1383)(550 - 72.68)2 = 3.106(10)9 mm4
3
M= wl2/8 = (9.3 + 10.7)(8)(8)/8 = 160kNm
I Ir
eff = Mr z x bw . (Eq. 7.1)
1.2 - (1- ) ( )
M d d b
Ir
I I
= = 0.875 I r . But I r eff gr
82.96 525.77 72.68 300
1.2 - ( )( ) (1- )( )
160 550 550 2234
Ief
So, f = Ir =3.106(10)9 mm4.
Step 3: Short-term deflection (sec. 7.17.5)
Ec = 5000 fck (cl. 6.2.3.1 of IS 456) = 22360.68 N/mm2
Short-term deflection = (5/384) wl4/EcIeff
= (5)(20)(8)4(1012)/(384)(22360.68)(3.106)(109) = 15.358 mm
(1)
Step 4: Deflection due to shrinkage (sec. 7.17.6)
k4 = 0.72( pt - pc )/pt= 0.72(0.84)0.84= 0.6599

cs = k4 cs / D= (0.6599)(0.0003)/600 = 3.2995(10) -7
k3 =0.125 (from sec. 7.17.6)

cs = k3 cs l 2 (Eq. 7.3) = (0.125)(3.2995)(10)-7(64)(106) = 2.64 mm
(2)
Step 5:Deflection due to creep (sec. 7.17.7)

cc(
Equation7.5revealsthatthedeflectionduetocreep perm ) canbe

1cc(
obtained after calculating 1cc( perm)and1( perm ) . We calculate perm) in the
next step.

Step 5a:Calculation of 1cc( perm )
Assuming the age of concrete at loading as 28 days, cl. 6.2.5.1 of IS 456 gives =
1.6. So, Ecc = Ec /(1 + ) = 22360.68/(1 + 1.6) = 8600.2615
N/mm2 and m = Es /Ecc = 200000/8600.2615 = 23.255
Step 5b: Properties of cracked section

Taking moment of compressive concrete and tensile steel about the neutral axis
(assuming at a distance of x from the bottom of the flange as shown in Fig.7.17.3):
2234(100)(50 +x )= (23.255)(1383)(450 -x ) or x= 12.92 mm
which givesx=112.92 mm. Accordingly, z=leverarm =dx/3=

512.36mm.
Ir=2234(100)3/12+ 2234(100)(62.92)2 + 23.255(1383)(550 112.92)2
+ 300(12.92)3/3 =7.214(109)mm4
Mr = 82.96 kNm (see Step 2)
M = wperm l2/8 = 9.3(8)(8)/8 = 74.4 kNm.
Ir
I =
eff = 0.918 I r
82.96 512.36 112.92 300
(1.2) - ( )( ) (1- )( )
74.4 550 550 2234
Ief
However, to satisfy Ir f Igr, Ieff should be equal to Igr. So, Ieff = Igr =
11.384(109). For the value of Igrplease see Step 1.

1cc(
Step 5c:Calculation of perm )

1cc( perm) = 5wl4/384(Ecc)(Ieff) =
5(9.3)(8)4(10)12/384(8600.2615)(11.384)(10 9)
=5.066mm
(3)

1( perm
Step 5d:Calculation of )

1( perm ) = 5wl4/384(Ec)(Ieff) =
5(9.3)(8)4(10)12/384(22360.68)(11.384)(109)
= 1.948 mm
(4)
Step 5e: Calculation of deflection due to creep

-
cc( perm ) = 1cc( perm ) 1( perm )
= 5.066 1.948 = 3.118 mm
(5)
It is important to note that the deflection due to creep cc( perm ) can be obtained
even without computing 1cc( perm) . The relationship of cc( perm) and

is given below.
1
(

cc( perm)= 1cc( perm)-1( perm )
p
4 e 1( perm ) ( )
= {5wl /384(Ec)(Ieff)} {(Ec /Ecc) 1}=
r
m
Hence, the deflection due to creep, for this problem is:
)
cc( perm) = 1( perm ) ( ) = 1.948(1.6) = 3.116 mm
Step 6: Checking of the requirements of IS 456
The two requirements regarding the control of deflection are given in sec. 7.17.3.
They are checked in the following:
Step 6a: Checking of the first requirement
The maximum allowable deflection = 8000/250 = 32 mm
The actual final deflection due to all loads
(xi) 15.358 (see Eq.1 of Step 3) + 2.64 (see Eq.2 of Step 4)
+ 3.118 (see Eq.5 ofStep 5e) =21.116 mm<32mm. Hence,

o.k.
Step 6b: Checking of the second requirement
The maximum allowable deflection is the lesser of span/350 or 20 mm. Here,

span/350 = 22.86 mm. So, the maximum allowable deflection = 20 mm. The actual final
deflection = 1.948 (see Eq.4 of Step 5d) + 2.64 (see Eq.2 of Step
4) + 3.118 (see Eq.5 of step 5e) = 7.706 mm < 20 mm. Hence, o.k.
Thus, both the requirements of cl.23.2 of IS 456 and as given in sec. 7.17.3 are
satisfied.
Q.1: Why is it essential to check the structures, designed by the limit state of collapse, by
the limit state of serviceability?
A.1: See sec. 7.17.1.
Q.2: Explain short- and long-term deflections and the respective influencing factors of
them.
A.2: See sec. 7.17.2.
Q.3: State the stipulations of IS 456 regarding the control of deflection.
A.3: See sec. 7.17.3.
Q.4: How would you select the preliminary dimensions of structures to satisfy (i) the
deflection requirements, and (ii) the lateral stability ?
A.4: See secs. 7.17.4 A for (i) and B for (ii).
Q.5: Check the preliminary cross-sectional dimensions of Problem 1 of sec. 7.17.8

(Fig.7.17.1) if they satisfy the requirements of control of deflection. The spacing
of the beam is 3.5 m c/c. Other data are the same as those of
Problem 1 of sec. 7.17.8.
A.5:
Step 1: Check for the effective width
bf = lo /6 + bw + 6Dfor spacing of the beam, whichever is less.
Here,bf = (8000/6) + 300 + 6(100)=2234<3500. Hence, bf=2234mm

is o.k.
Step 2: Check for span to effective depth ratio
(vii) As per row 1 of Table 7.1, the basic value of span to effective depth ratio is
20.
(viii) As per row 2 of Table 7.1, the modification factor is 1 since the span 8 m<
10 m.
(ix) As per row 5 of Table 7.1, the modification factor for the flanged beam is to be
obtained from Fig. 6 of IS 456 for which the ratio of web width to flange width
= 300/2234 = 0.134. Figure 6 of IS 456 gives the modification factor as 0.8. So, the
revised span to effective depth ratio = 20(0.8) = 16.
(iv) Row 3 of Table 7.1 deals with the area and stress of tensile steel. At the preliminary
stage these values are to be assumed. However, for this problem the
area of steel is given as 1383 mm2 (2-25T + 2-16T), for which pt = Ast(100)/bf d =
1383(100)/(2234)(550) = 0.112.
fs = 0.58 fy (area of cross-section of steel required)/(area of cross-section of steel
provided) = 0.58(415)(1) = 240.7 (assuming that the provided steel is the same as
required, which is a rare case). Figure 4 of IS 456 gives the modification factor as 1.8. So,
the revised span to effective depth ratio = 16(1.8) = 28.8.
(v) Row 4 is concerning the amount of compression steel. Here, compression steel is not
there. So, the modification factor = 1.
Therefore, the final span to effective depth ratio = 28.8.
Accordingly, effective depth of the beam = 8000/28.8 = 277.8 mm < 550

mm.
Hence, the dimensions of the cross-section are satisfying the requirements.
(vii) References
(iv) Reinforced Concrete Limit State Design, 6th Edition, by Ashok K. Jain, Nem
(v) Limit State Design of Reinforced Concrete, 2nd Edition, by P.C.Varghese,
(vi) Advanced Reinforced Concrete Design, by P.C.Varghese, Prentice-Hall of India
(vii) ReinforcedConcreteDesign,2ndEdition,byS.UnnikrishnaPillaiand
2003.
(viii) Limit State Design of Reinforced Concrete Structures, by P.Dayaratnam,
Oxford & I.B.H. Publishing Company Pvt. Ltd., New Delhi, 2004.
(ix) ReinforcedConcreteDesign,1stRevisedEdition,byS.N.Sinha,Tata
(x) Reinforced Concrete, 6th Edition, by S.K.Mallick and A.P.Gupta, Oxford & IBH
Publishing Co. Pvt. Ltd. New Delhi, 1996.
(xi) Behaviour, Analysis & Design of Reinforced Concrete Structural Elements, by
(xii) ReinforcedConcreteStructures,3rdEdition,byI.C.SyalandA.K.Goel,
15. Textbook of R.C.C, by G.S.Birdie and J.S.Birdie, Wiley Eastern Limited,
New Delhi, 1993.
16. DesignofConcreteStructures,13thEdition,byArthurH.Nilson,David
Darwin and Charles W. Dolan, Tata McGraw-Hill Publishing Company Limited,
New Delhi, 2004.
17. ConcreteTechnology,byA.M.NevilleandJ.J.Brooks,ELBSwith
Longman, 1994.
Longman, 2000.
20. Indian Standard Plain and Reinforced Concrete Code of Practice (4th Revision),
IS 456: 2000, BIS, New Delhi.
TQ.1: Explain short- and long-term deflections and the respective influencing factors of
them.
(10 marks)
A.TQ.1: See sec. 7.17.2.

TQ.2: Check the preliminary dimensions of a singly reinforced rectangular cantilever
beam of span 4 m (Fig.7.17.4) using M 20 and Fe 415. (15 marks)
A.TQ.2: (i) From row 1 of Table 7.1, the basic value of span to effective depth ratio is 7.
18. Modification factor for row 2 is 1 as this is a singly reinforced beam.

19. Assuming pt as 0.6 and area of steel to be provided is the same as area of
steel required, fs = 0.58(415(1) = 240.7 N/mm2. From Fig. 4 of IS 456, the modification
factor = 1.18. Hence, the revised span to effective depth ratio is 7(1.18) = 8.26.
Modification factors for rows 4 and 5 are 1 as there is no compression steel

and this being a rectangular beam. Hence, the preliminary effective depth needed =
4000/8.26 = 484.26 mm < 550 mm. Hence, o.k.
TQ.3: Determine the tensile steel of the cantilever beam of TQ 2 (Fig. 7.17.4) subjected
to service imposed load of 11.5 kN/m using M 20 and Fe 415.
Use Sp-16 for the design. Calculate short- and long-term deflections and check
the requirements of IS 456 regarding the deflection. (25 marks)
A.TQ.3: Determination of tensile steel of the beam using SP-16:
Dead load of the beam = 0.3(0.6)(25) kN/m = 4.5 kN/m
Service imposed loads = 11.5 kN/m
Total service load = 16.0 kN/m
Factored load = 16(1.5) = 24 kN/m

Mu = 24(4)(4)/2 = 192 kNm
For this beam of total depth 600 mm, let us assume d = 550 mm.
Mu /bd2 = 192/(0.3)(0.55)(0.55) = 2115.70 kN/m2
Table 2 of SP-16 gives the corresponding pt = 0.678 + 0.007(0.015)/0.02 = 0.683
Again, for Mu per metre run as 192/0.3 = 640 kNm/m, chart 15 of SP-16 gives pt
= 0.68 when d = 550 mm.
With pt = 0.683, Ast = 0.683(300)(500)/100 = 1126.95 mm2. Provide 4-
20T to have 1256 mm2. This gives provided pt = 0.761%.
Calculation of deflection
Step 1: Properties of concrete section

yt = D/2 = 300 mm, Igr = bD3/12 = 300(600)3/12 = 5.4(109) mm4
Step 2: Properties of cracked section
fcr = 0.720 (cl. 6.2.2 of IS 456)=3.13 N/mm2
yt =300 mm
fcr Igr
Mr = /yt =3.13(5.4)(109)/300=5.634(107)Nmm
Es = 200000N/mm2
Ec = 5000 fck(cl. 6.2.3.1 of IS 456)= 22360.68N/mm2
m= Es /Ec= 8.94
Taking moment of the compressive concrete and tensile steel about the neutral axis
(Fig.7.17.5):
300 x2/2 = (8.94)(1256)(550 x) or x2 + 74.86 x 41171.68 = 0

This gives x = 168.88 mm and z = d x/3 = 550 168.88/3 = 493.71 mm.
Ir= 300(168.88)3/3 + 8.94(1256)(550 168.88)2= 2.1126(109)mm4
M=wl2/2=20(4)(4)/2=160kNm
Ir
I
eff = = 1.02 I r = 2.1548 (109 ) mm4
5.634 493.71 168.88
(1.2) - ( )( ) (1- ) (1)
16 550 550
This satisfiesIr Ieff Igr. So, Ieff = 2.1548(109)mm4.
Step 3: Short-term deflection (sec. 7.17.5)

Ec = 22360.68 N/mm2 (cl. 6.2.3.1 of IS 456)
Short-term deflection = wl4/8EcIeff
= 20(44)(1012)/8(22360.68)(2.1548)(109) = 13.283 mm
So, short-term deflection = 13.283 mm

(1)
Step 4: Deflection due to shrinkage (sec. 7.17.6)
k4 = 0.72(0.761)/ 0.761 = 0.664

cs = k4 cs / D = (0.664)(0.0003)/600 = 3.32(10) -7
k3 =0.5 (from sec. 7.17.6)

cs = k3 cs l 2 = (0.5)(3.32)(10)-7(16)(106) = 2.656 mm
(2)
Step 5: Deflection due to creep (sec. 7.17.7)
Step 5a: Calculation of 1cc( perm)
Assuming the age of concrete at loading as 28 days, cl. 6.2.5.1 of IS 456

gives
= 1.6
So, Ecc = Ec /(1 + ) = 8600.2615 N/mm2
m = Es /Ecc = 200000/8600.2615 = 23.255
Step 5b: Properties of cracked section
From Fig.7.17.6, taking moment of compressive concrete and tensile steel about
the neutral axis, we have:
300 x2/2=(23.255)(1256)(550 - x)
or x2 + 194.72 x 107097.03=0
solving we getx=244.072 mm
z=d x/3=468.643 mm
Ir=300(244.072)3/3+ (23.255)(1256)(550 468.643)2
=1.6473(10)9mm4
Mr = 5.634( 107) Nmm (see Step 2)
M = wperm l2/2 = 4.5(42)/2 = 36 kNm
I
Ir
eff = = 2.1786 I r = 3.5888(109 ) mm4
5.634 468.643 244.072
1.2 - ( )( ) (1- ) (1)
3.6 550 550
Since this satisfies Ir Ieff Igr, we have, Ieff = 3.5888(109) mm4. For the value
of Igrplease see Step 1.
Step 5c: Calculation of 1cc( perm )
1cc( perm) = (wperm)( l4)/(8Ecc Ieff) = 4.5(4)4(10)12/8(8600.2615)(3.5888)(109)
= 4.665 mm
(3)
Step 5d: Calculation of 1( perm )
1( perm ) = (wperm)( l4)/(8Ec Ieff) = 4.5(4)4(10)12/8(22360.68)(3.5888)(109)
= 1.794 mm
(4)
Step 5e: Calculation of deflection due to creep

-
cc( perm ) = 1cc( perm ) 1( perm )
= 4.665 1.794 = 2.871 mm
(5)
Moreover: cc( perm) = 1cc( perm) ( ) gives cc( perm) = 1.794(1.6) = 2.874 mm.
Step 6: Checking of the two requirements of IS 456
Step 6a: First requirement
Maximum allowable deflection = 4000/250 = 16 mm
The actual deflection = 13.283 (Eq.1 of Step 3) + 2.656 (Eq.2 of Step 4)

+ 2.871 (Eq.5 of Step 5e) = 18.81 > Allowable 16
mm.
Step 6b: Second requirement
The allowable deflection is lesser of span/350 or 20 mm. Here,

span/350 =
11.428 mm is the allowable deflection. The actual deflection = 1.794
(Eq.4 of Step 5d) + 2.656 (Eq.2 of Step 4) + 2.871 (Eq.5 of step 5e) =
7.321 mm < 11.428 mm.
Remarks:
Though the second requirement is satisfying, the first requirement

is not satisfying. However the extra deflection is only 2.81 mm, which
can be made up by giving camber instead of revising the section.
This lesson illustrates the importance of checking the structures

for the limit state of serviceability after designing by the limit state of
collapse. The short-and long-term deflections along with their respective
influencing factors are explained. The code requirements for the control
of deflection and the necessary guidelines for the selection of dimensions
of cross-section are stated. Numerical examples, solved as illustrative
example and given in the practice problem and test will help the students
in understanding the calculations clearly for their application in the
design problems.
Flanged Beams Theory

and Numerical Problems
identify the two types of numerical problems analysis and design types,
apply the formulations to analyse the capacity of a flanged beam,
determine the limiting moment of resistance quickly with the help of tables of SP-
16.
(xii) Introduction
Lesson 10 illustrates the governing equations of flanged beams. It is now

necessary to apply them for the solution of numerical problems. Two types of numerical
problems are possible: (i) Analysis and (ii) Design types. This lesson explains the
application of the theory of flanged beams for the analysis type of problems. Moreover,
use of tables of SP-16 has been illustrated to determine the limiting moment of resistance
of sections quickly for the three grades of steel.
Besides mentioning the different steps of the solution, numerical examples are also taken
up to explain their step-by-step solutions.
5.11.2 Analysis Type of Problems

The dimensions of the beam bf, bw, Df, d, D, grades of concrete and steel and the
amount of steel Ast are given. It is required to determine the moment of resistance of the
beam.
Step 1: To determine the depth of the neutral axis xu
The depth of the neutral axis is determined from the equation of equilibrium C =
T. However, the expression of C depends on the location of neutral axis, Df /d and Df / xu
parameters. Therefore, it is required to assume first that the xu is in the flange. If this is
not the case, the next step is to assume xu in the web and the computed value of xu will
indicate if the beam is under-reinforced, balanced or over-reinforced.
Other steps:
After knowing if the section is under-reinforced, balanced or over-reinforced, the

respective parameter Df/d or Df/xu is computed for the under-reinforced, balanced or over-
reinforced beam. The respective expressions of C,
T and Mu, as established in Lesson 10, are then employed to determine their values.
Figure 5.11.1 illustrates the steps to be followed.
4.8.9 Numerical Problems (Analysis Type)
Ex.1: Determine the moment of resistance of the T-beam of Fig. 5.11.2. Given data: bf =
1000 mm, Df = 100 mm, bw = 300 mm, cover = 50 mm, d = 450 mm and Ast = 1963 mm2
(4- 25 T). Use M 20 and Fe 415.
Step 1: To determine the depth of the neutral axis xu
Assuming xu in the flange and equating total compressive and tensile forces from
the expressions of C and T (Eq. 3.16 of Lesson 5) as the T-beam can be treated as
rectangular beam of width bf and effective depth d, we get:
0.87f y Ast 0.87 (415) (1963)

xu = f
= = 98.44 mm < 100 mm
0.36 b f ck 0.36 (1000) (20)
So, the assumption of xu in the flange is correct.
xu, max for the balanced rectangular beam = 0.48 d = 0.48 (450) = 216
mm.
It is under-reinforced since xu < xu,max.
Step 2: To determine C, T and Mu
From Eqs. 3.9 (using b = bf) and 3.14 of Lesson 4 for C and T and Eq.
3.23 of Lesson 5 for Mu, we have:
C=0.36bfxufck (3.9)
= 0.36 (1000) (98.44) (20) = 708.77 kN

T = 0.87 fy Ast
(3.14)
= 0.87 (415) (1963) = 708.74 kN
A f
st y
M = 0.87 f Ad(1 - ) (3.23)
u y st
f
ckbf d
(1963) (415)
= 0.87 (415) (1963) (450) {1- (20) (1000) (450) } = 290.06 kNm
This problem belongs to the case (i) and is explained in sec. 5.10.4.1 of Lesson 10.
Ex.2: Determine Ast,lim and Mu,lim of the flanged beam of Fig. 5.11.3. Given data are: bf =
1000 mm, Df = 100 mm, bw = 300 mm, cover = 50 mm and d
= 450 mm. Use M 20 and Fe 415.
Step 1: To determine Df/d ratio
For the limiting case xu = xu,max = 0.48 (450) = 216 mm > Df. The ratio Df/d is
computed.
Df/d = 100/450 = 0.222 > 0.2
Hence, it is a problem of case (ii b) and discussed in sec. 5.10.4.2 b of Lesson 10.
Step 2: Computations of yf , C and T
First, we have to compute yf from Eq.5.8 of Lesson 10 and then employ Eqs. 5.9,
10 and 11 of Lesson 10 to determine C, T and Mu, respectively.
yf = 0.15 xu,max +0.65 Df = 0.15 (216) + 0.65 (100)=97.4 mm. (from

Eq. 5.8)
C = 0.36 fckbw xu,max+ 0.45fck (bf-bw) yf

(5.9)
= 0.36 (20) (300) (216) + 0.45 (20) (1000 - 300) (97.4) = 1,080.18 kN.
T= 0.87 fy Ast =0.87 (415) Ast

(5.10)
EquatingCandT, we have
(1080.18) (1000) N
A = = 2,991.77 mm2
s
t
0.87 (415) N/mm 2
Provide 4-28 T (2463 mm2) +3-16 T (603mm2)=3,066mm2
Step 3:Computation ofMu

x x
u, u,
max max
M = 0.36( ) {1 - 0.42( )} f bd2
u, c
lim k w
d d
+ 0.45 f (b - b ) y (d - y /2) (5.11)
c
k f w f f
= 0.36 (0.48) {1 - 0.42 (0.48)} (20) (300) (450)2
+ 0.45 (20) (1000 - 300) (97.4) (450 - 97.4/2) = 413.87 kNm
Ex.3: Determine the moment of resistance of the beam of Fig. 5.11.4 when Ast = 2,591
mm2 (4- 25 T and 2- 20 T). Other parameters are the same as those of Ex.1: bf = 1,000
mm, Df = 100 mm, bw = 300 mm, cover = 50 mm and d = 450 mm. Use M 20 and Fe 415.
Step 1: To determine xu
Assuming xu to be in the flange and the beam is under-reinforced, we have from

Eq. 3.16 of Lesson 5:
0.87f yAst 0.87 (415) (2591)

x
u = = = 129.93 mm > 100 mm
0.36 b ff ck 0.36 (1000) (20)
Since xu > Df, the neutral axis is in web.Here, Df/d=100/450=0.222>0.2.

So, we have to substitute the term yf from Eq. 5.15 of Lesson 10, assuming Df /
xu> 0.43 in the equation ofC =Tfrom Eqs. 5.16 and 17 ofsec. 5.10.4.3 b of
Lesson 10. Accordingly, we get:
0.36 fckbwxu+ 0.45fck (bf- bw) yf=0.87 fy Ast
or 0.36 (20) (300) (xu) + 0.45 (20) (1000 - 300) {0.15 xu + 0.65 (100)}
=0.87 (415) (2591)
or xu =169.398mm<216 mm (xu,max = 0.48 xu = 216 mm)

So, the section is under-reinforced.
Step 2: To determine Mu
Df /xu = 100/169.398 = 0.590 > 0.43
This is the problem of case (iii b) of sec. 5.10.4.3 b. The corresponding equations are Eq.
5.15 of Lesson 10 for yf and Eqs. 5.16 to 18 of Lesson 10 for C, T and
Mu, respectively. From Eq. 5.15 of Lesson 10, we have:
yf = 0.15 xu + 0.65 Df = 0.15 (169.398) + 0.65 (100) = 90.409 mm
From Eq. 5.18 of Lesson 10, we have

Mu = 0.36(xu /d){1 - 0.42( xu /d)} fck bw d2 + 0.45 fck(bf - bw) yf (d - yf /2)
or Mu = 0.36 (169.398/450) {1 - 0.42 (169.398/450)} (20) (300) (450) (450)
(iii) 0.45 (20) (1000 - 300) (90.409) (450 - 90.409/2)
7 138.62 + 230.56=369.18kNm.
Ex.4: Determine the moment of resistance of the flanged beam of Fig. 5.11.5 with Ast =
4,825 mm2 (6- 32 T). Other parameters and data are the same as those of Ex.1: bf = 1000
mm, Df = 100 mm, bw = 300 mm, cover = 50 mm and d = 450 mm. Use M 20 and Fe 415.
Step 1: To determine xu
Assuming xu in the flange of under-reinforced rectangular beam we have from Eq.

3.16 of Lesson 5:
0.87f yAst 0.87 (415) (4825)

x
u = = = 241.95 mm > D f
f
0.36 b f ck 0.36 (1000) (20)
Here, Df/d=100/450= 0.222> 0.2. So, we have to determine yffrom Eq.
5.15 and equating C and T from Eqs. 5.16 and 17 of Lesson 10.
yf = 0.15 xu +0.65Df (5.15)
0.36 fckbwxu+ 0.45fck (bf- bw) yf=0.87 fy Ast (5.16 and

5.17)
or 0.36 (20) (300) (xu) + 0.45 (20) (1000 - 300) {0.15 xu + 0.65 (100)}
= 0.87 (415) (4825)
or 2160 xu +945 xu =-409500+ 1742066
or xu =1332566/3105=429.17 mm
xu,m
ax =0.48 (450)=216 mm
Since xu > xu,max, the beam is over-reinforced. Accordingly.
xu =xu, max =216 mm.
Step 2:To determineMu
This problem belongs to case (iv b), explained in sec.5.10.4.4 b of Lesson

10. So, we can determine Mufrom Eq. 5.11 of Lesson 10.
Mu = 0.36(xu, max /d){1 - 0.42(xu, max /d)} fck bw d2 + 0.45fck(bf - bw) yf (d - yf

/2)
(5.11)
where yf =0.15 xu, max+0.65Df =97.4mm

(5.8)
From Eq. 5.11, employing the value of yf = 97.4 mm, we get:
Mu = 0.36 (0.48) {1 - 0.42 (0.48)} (20) (300) (450) (450)
+ 0.45 (20) (1000 - 300) (97.4) (450 - 97.4/2)
= 167.63 + 246.24 = 413.87 kNm

It is seen that this over-reinforced beam has the same Mu as that of the balanced beam of
Example 2.
5.11.4 Summary of Results of Examples 1-4
The results of four problems (Exs. 1-4) are given in Table 5.1 below. All the
examples are having the common data except Ast.
Table 5.1 Results of Examples 1-4 (Figs. 5.11.2 5.11.5)
Ex. Ast Case Section Mu Remarks

No. (mm2) No. (kNm)
1 1,963 (i) 5.10.4.1 290.06 xu = 98.44 mm < xu, max (= 216
mm),
xu<Df (= 100 mm),
Under-reinforced, (NA in the
flange).
2 3,066 (ii b) 5.10.4.2 413.87 xu =xu, max= 216 mm,
(b) Df /d = 0.222 > 0.2,
Balanced, (NA in web).
3 2,591 (iii b) 5.10.4.3 369.18 xu = 169.398 mm < xu, max(= 216
(b) mm),
Df /xu= 0.59 > 0.43,
Under-reinforced, (NA in the
web).
4 4,825 (iv b) 5.10.4.4 413.87 xu =241.95 mm > xu, max (= 216
(b) mm),
Df /d=0.222 > 0.2,
Over-reinforced, (NA in web).
It is clear from the above table (Table 5.1), that Ex.4 is an over-reinforced flanged
beam. The moment of resistance of this beam is the same as that of balanced beam of
Ex.2. Additional reinforcement of 1,759 mm2 (= 4,825 mm2 3,066 mm2) does not
improve the M u of the over-reinforced beam. It rather prevents the beam from tension
failure. That is why over-reinforced beams are to be avoided. However, if the Mu has to
be increased beyond 413.87 kNm, the flanged beam may be doubly reinforced.
5.11.5 Use of SP-16 for the Analysis Type of Problems

Using the two governing parameters (bf /bw) and (Df /d), the Mu,lim of balanced
flanged beams can be determined from Tables 57-59 of SP-16 for the
three grades of steel (250, 415 and 500). The value of the moment coefficient
Mu,lim /bwd2fck of Ex.2, as obtained from SP-16, is presented in Table 5.2 making linear
interpolation for both the parameters, wherever needed. Mu,lim is then
calculated from the moment coefficient.
Table 5.2 Mu,lim of Example 2 using Table 58 of SP-16
Parameters:(i) bf /bw = 1000/300 =3.33

(ii) Df /d = 100/450 = 0.222
(Mu,lim /bw d2 fck)inN/mm2

Df /d bf /bw
3 4 3.33
0.22 0.309 0.395
0.23 0.314 0.402
0.222 0.31* 0.3964* 0.339*
*by linear interpolation
M
u, lim
So, from Table 5.2, = 0.339
bw d 2 fck
Mu,lim= 0.339 bw d2 fck = 0.339 (300) (450) (450) (20) 10-6=411.88
kNm
Mu,lim as obtained from SP-16 is close to the earlier computed value of Mu,lim = 413.87
kNm (see Table 5.1).

Q.1: Determine the moment of resistance of the simply supported doubly reinforced
flanged beam (isolated) of span 9 m as shown in Fig. 5.11.6. Assume M 30
concrete and Fe 500 steel.
A.1:Solution of Q.1:
l
o 9000
Effective widthbf= + bw = + 300 = 1200 mm
(lo /b) + 4 (9000/1500) + 4
Step 1: To determine the depth of the neutral axis
Assuming neutral axis to be in the flange and writing the equation C = T, we

have:
0.87 fy Ast = 0.36 fck bf xu + (fsc Asc fcc Asc)
Here, d ' / d = 65/600 = 0.108 = 0.1 (say). We, therefore, have fsc = 353 N/mm2 .
From the above equation, we have:
xu= 0.87 (500) (6509) -{(353) (1030) - 0.446 (30) (1030)} = 191.48 mm >120
0.36 (30) (1200) mm
So, the neutral axis is in web.
Df /d= 120/600=0.2
AssumingDf /xu <0.43, andEquatingC = T
0.87 fy Ast =0.36 fck bw xu+ 0.446 fck (bf bw) Df

+ (fsc fcc) Asc
x= 0.87 (500) (6509) - 1030{353 - 0.446 (30)}- 0.446 (30) (1200 - 300) (120)
u
0. 36 ( 30 ) ( 300 )
= 319.92> 276 mm (xu ,max = 276 mm)
So, xu = xu,max = 276 mm (over-reinforced beam).

Df /xu = 120/276 = 0.4347 > 0.43
Let us assume Df /xu > 0.43. Now, equating C = T with yf as the depth of flange having
constant stress of 0.446 fck. So, we have:
yf = 0.15 xu + 0.65 Df = 0.15 xu + 78
0.36 fck bw xu + 0.446 fck (bf bw) yf + Asc (fsc fcc) = 0.87 fy Ast
0.36 (30) (300) xu + 0.446 (30) (900) (0.15 xu + 78)
= 0.87 (500) (6509) 1030 {353 0.446 (30)}

or xu = 305.63 mm > xu,max. (xu,max = 276 mm)
The beam is over-reinforced. Hence, xu = xu,max = 276 mm. This is a problem of case (iv),
and we, therefore, consider the case (ii) to find out the moment of
resistance in two parts: first for the balanced singly reinforced beam and then for the
additional moment due to compression steel.
Step 2: Determination of xu,lim for singly reinforced flanged beam
Here, Df /d = 120/600 = 0.2, so yf is not needed. This is a problem of case (ii a) of sec.
5.10.4.2 of Lesson 10. Employing Eq. 5.7 of Lesson 10, we have:
Mu,lim = 0.36 (xu,max /d) {1 0.42 (xu,max /d)} fck bw d2
i 0.45 fck (bf bw) Df (d Df /2)
4.8.8 0.36(0.46) {1 0.42(0.46)} (30) (300) (600)

(600) + 0.45(30) (900) (120) (540)
4.8.9 1,220.20kNm
A M
st u ,lim
,lim =
0.87 f y d {1 - 0.42 (xu,max / d )}
(1220.20) (106 ) 2
= = 5,794.6152mm
( 0.87 ) ( 500 ) ( 600 ) ( 0.8068 )
Step 3:Determination ofMu2
TotalAst=6,509mm2,Ast,lim =5,794.62mm2
Ast2 = 714.38 mm2 and Asc = 1,030 mm2
It is important to find out how much of the total Asc and Ast2 are required effectively.
From the equilibrium of C and T forces due to additional steel
(compressive and tensile), we have:
(Ast2) (0.87) (fy) = (Asc) (fsc)
If we assume Asc = 1,030 mm2
Ast 2 = 10300.87 (500)(353) = 835.84 mm2 > 714.38 mm2 , (714.38 mm2 is the total
Ast2 provided). So, this is not possible.
Now, using Ast2 = 714.38 mm2 , we get Asc from the above equation.
(714.38) (0.87) (500)

A = = 880.326 < 1,030 mm2 , (1,030 mm2is
sc
353
the total Asc provided).
M
u 2 = Asc f sc (d - d ') = (880.326) (353) (600 - 60) = 167.807 kNm
Total moment of resistance= Mu,lim + Mu2= 1,220.20 + 167.81= 1,388.01
kNm
TotalAst required=Ast,lim + Ast2 =5,794.62 + 714.38= 6,509.00mm2 ,

(provided Ast = 6,509 mm2)
Asc required=880.326mm2 (provided 1,030mm2).

5.11.7 References
(iv) Reinforced Concrete Limit State Design, 6th Edition, by Ashok K. Jain, Nem
(v) Limit State Design of Reinforced Concrete, 2nd Edition, by P.C.Varghese,
(vi) Advanced Reinforced Concrete Design, by P.C.Varghese, Prentice-Hall of
India Pvt. Ltd., New Delhi, 2001.
(vii) Reinforced Concrete Design, 2nd Edition, by S.Unnikrishna Pillai and
2003.
(viii) Limit State Design of Reinforced Concrete Structures, by P.Dayaratnam,
Oxford & I.B.H. Publishing Company Pvt. Ltd., New Delhi, 2004.
(ix) ReinforcedConcreteDesign,1stRevisedEdition,byS.N.Sinha,Tata
(x) Reinforced Concrete, 6th Edition, by S.K.Mallick and A.P.Gupta, Oxford &
IBH Publishing Co. Pvt. Ltd. New Delhi, 1996.
(xi) Behaviour, Analysis & Design of Reinforced Concrete Structural Elements, by
(xii) Reinforced Concrete Structures, 3rd Edition, by I.C.Syal and A.K.Goel,
(xiii) Textbook of R.C.C, by G.S.Birdie and J.S.Birdie, Wiley Eastern Limited,
New Delhi, 1993.
(xii) DesignofConcreteStructures,13thEdition,byArthurH.Nilson,David
Darwin and Charles W. Dolan, Tata McGraw-Hill Publishing Company Limited,
New Delhi, 2004.
(xiii) Concrete Technology, by A.M.Neville and J.J.Brooks, ELBS with
Longman, 1994.
(xiv) PropertiesofConcrete,4thEdition,1stIndianreprint,byA.M.Neville,
Longman, 2000.
(xv) Reinforced Concrete Designers Handbook, 10th Edition, by C.E.Reynolds
and J.C.Steedman, E & FN SPON, London, 1997.
(xvi) Indian Standard Plain and Reinforced Concrete Code of Practice (4th
Revision), IS 456: 2000, BIS, New Delhi.
(xvii) Design Aids for Reinforced Concrete to IS: 456 1978, BIS, New Delhi.

TQ.1: Determine Mu,lim of the flanged beam of Ex. 2 (Fig. 5.11.3) with the help of SP-16
using (a) M 20 and Fe 250, (b) M 20 and Fe 500 and (c) compare the results with the
Mu,lim of Ex. 2 from Table 5.2 when grades of concrete and steel are M 20 and Fe 415,
respectively. Other data are: bf = 1000 mm, Df = 100 mm, bw = 300 mm, cover = 50 mm
and d = 450 mm.
(10 X 3 = 30 marks)
A.TQ.1: From the results of Ex. 2 of sec. 5.11.5 (Table 5.2), we have:
Parameters:(i)bf /bw = 1000/300 =3.33

(ii) Df /d = 100/450= 0.222
For part (a): When Fe 250 is used, the corresponding table is Table 57 of SP-16. The
computations are presented in Table 5.3 below:
Table 5.3(Mu,lim /bw d2 fck)inN/mm2 Of TQ.1 (PART a for M 20 and Fe 250)
(Mu,lim /bw d2 fck)inN/mm2

Df /d bf /bw
3 4 3.33
0.22 0.324 0.411
0.23 0.330 0.421
0.222 0.3252* 0.413* 0.354174*
(x) by linear interpolation
Mu,lim /bw d2 fck = 0.354174 = 0.354 (say)
So, Mu,lim = (0.354) (300) (450) (450) (20) N mm = 430.11 kNm
For part (b): When Fe 500 is used, the corresponding table is Table 59 of SP-
16. The computations are presented in Table 5.4 below:
Table 5.4 (Mu,lim /bw d2 fck) in N/mm2 2Of TQ.1 (PART2 b for M 20 and Fe 500)
(Mu,lim /bw d fck) in N/mm
Df /d bf /bw
3 4 3.33
0.22 0.302 0.386
0.23 0.306 0.393
0.222 0.3028* 0.3874* 0.330718*
* by linear interpolation
Mu,lim /bw d2 fck= 0.330718 = 0.3307 (say)

So, Mu,lim =(0.3307) (300) (450) (450) (20) mm= 401.8kNm
For part (c): Comparison of results of this problem with that of Table 5.2 (M 20 and Fe
415) is given below in Table 5.5.
Table 5.5 Comparison of results of Mu,lim
Sl. Grade of Steel Mu,lim(kNm)

No.
1 Fe 250 430.11
2 Fe 415 411.88
3 Fe 500 401.80
It is seen that Mu,lim of the beam decreases with higher grade of steel for a
particular grade of concrete.
TQ.2: With the aid of SP-16, determine separately the limiting moments of resistance
and the limiting areas of steel of the simply supported isolated, singly reinforced
and balanced flanged beam of Q.1 as shown in Fig. 5.11.6 if the span = 9 m. Use
M 30 concrete and three grades of steel, Fe
250, Fe 415 and Fe 500, respectively. Compare the results obtained above with
that of Q.1 of sec. 5.11.6, when balanced.
(15 + 5 = 20 marks)
A.TQ.2: From the results of Q.1 sec. 5.11.6, we have:
Parameters:(i)bf /bw = 1200/300 =4.0

(ii) Df /d = 120/600= 0.2
For Fe 250, Fe 415 and Fe 500, corresponding tables are Table 57, 58 and 59,
respectively of SP-16. The computations are done accordingly. After computing the
limiting moments of resistance, the limiting areas of steel are determined as explained
below. Finally, the results are presented in Table 5.6 below:
A M
st u ,lim
,lim =
0.87 f y d {1 - 0.42 (xu,max / d )}
Table 5.6 Values of Mu,lim inN/mm2 Of TQ.2
(Mu,lim/b
GradeofFe/Q.1of w d2fck) Mu,lim (kNm) Ast,lim (mm2)
sec. 5.11.6 (N/mm2 )
Fe 250 0.39 1, 263.60 12,455.32
Fe 415 0.379 1, 227.96 7,099.78
Fe 500 0.372 1, 205.28 5,723.76
Q.1ofsec.5.11.6(Fe 1, 220.20 5,794.62
415)
The maximum area of steel allowed is .04 b D = (.04) (300) (660) = 7,920 mm2 .
Hence, Fe 250 is not possible in this case.
(viii) Summary of this Lesson
This lesson mentions about the two types of numerical problems (i) analysis and
(ii) design types. In addition to explaining the steps involved in solving the analysis type
of numerical problems, several examples of analysis type of problems are illustrated
explaining all steps of the solutions both by direct computation method and employing
SP- 16. Solutions of practice and test problems will give readers the confidence in
applying the theory explained in Lesson 10 in solving the numerical problems.

Mallick Gupta Notes PDF

Uploaded by

Copyright:

Available Formats

Mallick Gupta Notes PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mallick Gupta Notes PDF

Uploaded by

Copyright:

Available Formats

LECTURE NOTES

Mr. Gude Ramakrishna

At the end of this lesson, the student should be able to:

explain the situations when doubly reinforced beams are designed,

(ii) the ductility requirement has to be followed.

(iii) the reduction of long term deflection is needed.

4.8.3 Basic Principle

As mentioned in sec. 4.8.1, the moment of resistance Mu of the doubly reinforced

The Mu,lim is as given in Eq. 3.24 of Lesson 5, i.e.,

Mu, lim= 0.87 Ast, lim fy (d - 0.42 xu, max)

Ast2 = area of additional steel reinforcement

The total tensile reinforcement Ast is then obtained from:

(a) Mild steel Fe 250

(ii) If the computed value of sc > 0.0010869, fsc = 217.39 N/mm2.

(b) Cold worked bars Fe 415 and Fe 500

Stress level Fe 415 Fe 500

Strain sc Stressfsc Strainsc Stressfsc

= 0.002+ 1.15 (200000) = 0.0038043

(iii) The strain at yield of Fe 500 = 0.002+ 1.15 (200000) = 0.0041739

(N/mm2) 0.05 0.10 0.15 0.20 yield

4.8.5 Minimum and maximum steel

There is no stipulation in IS 456 regarding the minimum compression steel in

4.8.6.1 Design type of problems

(a) Direct computation method

Step 3: To check for minimum and maximum reinforcement in compression and

(b) Use of SP table

(a) Direct computation method

Step 1: To check if the beam is under-reinforced or over-reinforced.

(b) Use of tables of SP-16

4.8.7 Practice Questions and Problems with Answers

Q.1: When do we go for doubly reinforced beams ?

A.2: Compression reinforcement is provided when:

(iii) the reduction of long term deflection is needed.

A.3: See sec. 4.8.2 (i), (ii) and (iii).

Q.4: Derive the governing equations of a doubly reinforced beam.

A.4: See sec. 4.8.3

A.5: See sec. 4.8.4

A.6: See sec. 4.8.5

A.7: The two types of problems are:

(i) Design type ofproblems and

(i) Design type of problems:

(ii) Analysis type of problems:

(i) Direct computation method, and

A.9: (A) For the design type of problems:

(B) For the analysis type of problems:

4.8.9 Test 8 with Solutions

Maximum Marks = 50, Maximum Time = 30 minutes

Answer all questions.

TQ.1: Derive the governing equations of a doubly reinforced beam.

A.TQ.1: See sec. 4.8.3

A.TQ.2: The two types of problems are:

(i) Design type ofproblems and

(i) Design type of problems:

(ii) Analysis type of problems:

(B) For the analysis type of problems:

(ii) the ductility requirement has to be satisfied,

(iii) the reduction of long term deflection is needed.

4.8.10 Summary of this Lesson

Lesson 8 derives the governing equations of the doubly reinforced beams