810 - 820 Reload PDF

Siemens 810/820 Service Course 1
810 / 820 Service Course
How to reload your NC?
Siemens PLC 810/820 Service Course

Training Centre
Reloading your Control

If you power up your control and it is either visibly corrupted, power up in German or the screen
does not power up at all; you then need to follow the procedure below to reload your control
from your backup.
Firstly you need to power up your control with the eyeball key pressed .Power the control off
the press the EYEBALL key on the control then power the control on while keeping
the Eyeball key pressed.
When your control has powered up it should be in INITAIL CLEAR MODE. This mode allows
you to clear out all the corrupted data.
If your control has powered up in German press MACH-DATEN (forth soft key) if its in English
press MACHINE DATA.
Starting with the first soft key on the left press four soft-keys in total. You should see small ticks
appear against options on the screen.
Press the RECALL Button to go back to the screen you powered up in.
Press PLC INITIAL, this is the same in German and English (third soft key).
Press the first two soft-keys from the left. Again ticks will appear against the options.
If in German press NC DATEN in English it will be NC DATA (second soft key).

Press the first three soft-keys from the left. Ticks again will appear against the options.
You have now cleared out all the corrupted data. If the control is in German it is preferable to
change the language to English. To do this follow the steps below.
How to select English.

After you have carried out the above steps you need to do the following to make to control
display English.
Press INBETR ENDE (last soft key).
The control will now power off and then back up again normal running mode.
Press DIAGNOSE (if Diagnose is not present press and the option should then
appear)
Then press the RIGHT SCROLL Button so that you see NC MD and press the soft
key.
Type 250 then the search button this will highlight the Machine Data. Machine Data
250 is for either a Milling machine or a Lathe and Machine Data 199 for either a Grinder or a
Nibbling machine and is for Language Selection.
Now press the EYEBALL Button.
Type 1111
Press the ENTER Button

Training Centre
Type 1 and press ENTER Button accept the setting.
Press the EYEBALL Button
Press the first soft key on the Left.

The control should now power off and back on again in INITIAL CLEAR Mode but this time in
English.
Reloading Your Data.

Once the control has powered back up you can now reload your data.
Press MACHINE DATA (forth soft key).
Starting with the first soft key on the left press four soft-keys in total. You should see small ticks
appear against options on the screen. This will clear any machine data and load Standard
machine data for both the NC & PLC.
Press PLC INITIAL (third soft key).

Press the first two soft-keys from the left. Again ticks will appear against the options. This will
clear the PLC Program and also clear any Retentive Flags from the PLC memory.
Press NC DATA (second soft key).

Press the first three soft-keys from the left. Ticks again will appear against the options. This will
Format the USER Data, Clear the Part Program & Clear the Alarm Text.
Now press DATA IN/OUT (first soft key).

You will now see the Setting Data page. You now need to input the correct port settings for
data transfer using PCIN.
The settings are as follows:-
5010 = 00000000 - This sets the device as RTS
5011 = 11000111 - This sets 2 Stop Bits, 7 Data Bits & 9600 Baud
5016 = 00101000 - This sets Data Transmission details.
You now need get your PC / PG ready for transmission.
Starting Pcin:
Double click on the pcin icon on the desktop

Training Centre
Pcin Settings:
When Pcin has loaded up, use the your cursor keys to
highlight V24_INI.
When highlighted press ENTER.

Use your up & down cursors to highlight the settings and then
your left & right cursors to select the correct settings.
Following settings should be used: -

COM NUMBER 1
BAUDRATE 9600
PARITY EVEN
STOPBITS 2
DATABITS 7
TIMEOUT 4s
BINFILE OFF
Once you have completed your settings press ENTER & then
press Y for SAVE INPUT. This will then set your port
settings for data transmission.
Changing into the directory

you have created
Once you have created a directory, you must
now change directory so that all the data is
saved in it.
Highlight FILE using your cursors.
Press ENTER so that the drop down menu
appears.
Again use your cursor to highlight
CHANGE DIR.
Press ENTER on your PC.
When the box appears showing the

directory which you are in press the
SPACE BAR on the PC. This will clear the
box.
Press ENTER on the PC and the window
opposite will appear.
Use your cursor to highlight the directory,
which you have created.
Press F2, this will accept the directory.

Training Centre
You now need to start to reload your data from your PC to the NC in order.
On you PC highlight DATA OUT and press your ENTER Button.
Press your SPACE BAR on your PC to clear the contents of the window.
Press the ENTER Button on your PC.
Now using your cursor highlight TEA1
Now press ENTER on the PC.

Your PC will now wait.
On your NC press DATA IN/OUT.
Connect your RS232 cable COM1 of the PC & the Front interface of the NC
Type 1 then ENTER on the NC. This will set the interface number.
You will see the Data transfer from the PC to the NC.
Repeat the procedure above but this time select TEA2 on the PC to transfer.
When you have transferred TEA1 & TEA2 press on the NC.
Press END SETUP PW (last soft key) on the right.

When the control powers up it will be in normal running mode.
You need to go back into INITAIL CLEAR Mode.
Now press the EYEBALL Button.
Type 1111
Press the ENTER Button
Press the EYEBALL Button
Press the first soft key on the Left.

Training Centre
The control should now power off and back on again in INITIAL CLEAR Mode.
Press PLC INITIAL (third soft key).
Press the first two soft-keys from the left. Again ticks will appear against the options. This will
clear the PLC Program and also clear any Retentive Flags from the PLC memory.
Press NC DATA (second soft key).

Press the first three soft-keys from the left. Ticks again will appear against the options. This will
Format the USER Data, Clear the Part Program & Clear the Alarm Text.
Now press DATA IN/OUT (first soft key).

You will now see the Setting Data page. You now need to input the correct port settings for
data transfer using PCIN.
The settings are as follows:-
5010 = 00000000 - This sets the device as RTS
5011 = 11000111 - This sets 2 Stop Bits, 7 Data Bits & 9600 Baud
5016 = 00101000 - This sets Data Transmission details.
Now on your PC Highlight DATA OUT.
Press ENTER on the PC.
Press your Space Bar to clear the window.
Using your cursor keys highlight PCP.
Then press Enter on your PC.
Your PC will now wait.
On your NC press DATA IN.
Type 1 then ENTER on the NC. This will set the interface number.
You will see the Data transfer from the PC to the NC.
Repeat the procedure above but this time select PCA on the PC to transfer.
When you have transferred PCP & PCA press on the NC.
Press END SETUP PW (last soft key on the right.)

On the NC press DATA IN/OUT.
Press DATA IN START.
On the PC Highlight DATA OUT.
Press the Space Bar to clear the window.

Training Centre
Using ALT T select any files which you have not already transferred. You will see an asterix
appear next to each file you tag. Do not tag any file with a .DIR extension and make sure that
when you have selected all your files that you leave the highlight over one of the tagged files.
The rest of the files will now be transferred.
When finished press DATA STOP on the NC.
Your NC should now be ready for operation.

Training Centre

810 - 820 Reload PDF

Uploaded by

Copyright:

Available Formats

810 - 820 Reload PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

810 - 820 Reload PDF

Uploaded by

Copyright:

Available Formats

Siemens 810/820 Service Course 1

810 / 820 Service Course

How to reload your NC?

Siemens PLC 810/820 Service Course

Reloading your Control

If in German press NC DATEN in English it will be NC DATA (second soft key).

How to select English.

Now press the EYEBALL Button.

Siemens PLC 810/820 Service Course

Type 1 and press ENTER Button accept the setting.

Press the EYEBALL Button

Press the first soft key on the Left.

Reloading Your Data.

Press PLC INITIAL (third soft key).

Press NC DATA (second soft key).

Now press DATA IN/OUT (first soft key).

Double click on the pcin icon on the desktop

Siemens PLC 810/820 Service Course

When highlighted press ENTER.

Following settings should be used: -

Changing into the directory

When the box appears showing the

Siemens PLC 810/820 Service Course

Now press ENTER on the PC.

Press END SETUP PW (last soft key) on the right.

Now press the EYEBALL Button.

Press the EYEBALL Button

Press the first soft key on the Left.

Siemens PLC 810/820 Service Course

Press NC DATA (second soft key).

Now press DATA IN/OUT (first soft key).

Press END SETUP PW (last soft key on the right.)

Siemens PLC 810/820 Service Course

Siemens PLC 810/820 Service Course

You might also like