PGJ

Gear Driven Sprinklers

To decrease arc:
Radius Reduction Screw 1. Insert the key end of the Hunter wrench
into the adjustment socket.
2. While holding the nozzle turret at the right

stop, turn the wrench counterclockwise.
Pull-up
Socket 3. Wrench will stop turning when adjusted to
PGJ the minimum arc (40). Do not go past this
M AD

V stop.
EI
N
US

A
4. Adjust to any arc between 40-360.

Plus+ Minus -- Arc Adjustment Radius Adjustment

To decrease radius:
1. Turn nozzle-retainer/range-adjustment
Arc Adjustment screw clockwise using hex end of Hunter
tool or slot screwdriver. This can reduce
(All PGJ adjustable heads are PRESET to
radius up to 25%.
approximately 40)
2. If an even smaller radius is desired, install
1. Rotate the nozzle turret counterclockwise a smaller nozzle. This will affect precipita-
to the left stop. tion rate.
2. Now, rotate the nozzle turret clockwise to
To increase radius:
the right stop. This is the fixed side of the
1. Turn nozzle-retainer/range-adjustment
arc. The nozzle turret must be held in this
screw counterclockwise using hex end of
position for all arc adjustments.
Hunter tool or slot screwdriver.
To increase arc: 2. If larger radius is desired, install larger
1. Insert the key end of the Hunter wrench nozzle. This will affect precipitation rate.
into the adjustment socket on top of the
sprinkler. Precipitation Rate Adjustment
2. While holding the nozzle turret at the right To increase precipitation:
stop, turn the wrench clockwise. 1. Remove existing nozzle.
3. Wrench will stop turning when adjusted to 2. Replace with larger size.
the maximum arc (360). Do not go past 3. Adjust radius.
this stop.
To decrease precipitation:
4. Adjust to any arc between 40- 360. 1. Remove existing nozzle.
2. Replace with smaller size.
3. Adjust radius.
Note: Undamaged nozzles are reusable.

Hunter Industries Incorporated The Irrigation Innovators 2004 Hunter Industries Incorporated
www.HunterIndustries.com P/N 700974 LIT-379 3/04
 PGJ
Gear Driven Sprinklers

Nozzle Installation
1. Insert the plastic key end of the Hunter 25 so that the nozzle range screw threads
wrench into the lifting socket of the sprin- directly down. Then tighten the nozzle
kler and turn 90. Pull the riser up to gain range screw. The arrow on the rubber
access to the nozzle socket. cover will always indicate the location of
the nozzle and direction of the water flow
2. Using the hex key of the Hunter wrench,
when the sprinkler is retracted.
turn the radius adjustment screw coun-
terclockwise to be sure it is not blocking Removing Filter Screen Proper Installation
the nozzle socket opening. If a nozzle is for Cleaning Height
already installed, it can be removed by
backing out the adjustment screw and
turning on the water, or by prying outward
under the nozzle.
3. Slip the desired nozzle into the nozzle
socket. Note that the socket is angled up

PGJ Nozzle Performance Data PGJ Nozzle Performance Data Metric

Pressure Radius Flow Precip in/hr Pressure Radius Flow Precip mm/hr
Nozzle PSI ft. GPM Nozzle Bars kPa m m3/hr l/min
30 15' 0.64 0.55 0.63 2.1 206 4.6 0.15 2.4 14 16
.75 40
50
16'
17'
0.75
0.85
0.56
0.57
0.65
0.65
.75 2.8
3.4
275
344
4.9
5.2
0.17
0.19
2.8
3.2
14
14
17
17
30 18' 0.85 0.51 0.58 2.1 206 5.5 0.19 3.2 13 15
1.0 40
50
19'
19'
1.0
1.1
0.53
0.59
0.62
0.68
1.0 2.8
3.4
275
344
5.8
5.8
0.23
0.25
3.8
4.2
14
15
16
17
30 21' 1.3 0.57 0.66 2.1 206 6.4 0.30 4.9 14 17
1.5 40
50
22'
22'
1.5
1.7
0.60
0.68
0.69
0.78
1.5 2.8
3.4
275
344
6.7
6.7
0.34
0.39
5.7
6.4
15
17
18
20
30 24' 1.7 0.57 0.66 2.1 206 7.3 0.39 6.4 14 17
2.0 40
50
25'
25'
2.0
2.3
0.62
0.71
0.71
0.82
2.0 2.8
3.4
275
344
7.6
7.6
0.45
0.52
7.6
8.7
16
18
18
21
30 27' 2.2 0.58 0.67 2.1 206 8.2 0.50 8.3 15 17
2.5 40
50
28'
28'
2.5
2.8
0.61
0.69
0.71
0.79
2.5 2.8
3.4
275
344
8.5
8.5
0.57
0.64
9.5
10.6
16
18
18
20
30 30' 2.5 0.53 0.62 2.1 206 9.1 0.57 9.5 14 16
3.0 40
50
31'
31'
3.0
3.4
0.60
0.68
0.69
0.79
3.0 2.8
3.4
275
344
9.4
9.4
0.68
0.77
11.4
12.9
15
17
18
20
30 33' 3.7 0.65 0.76 2.1 206 10.1 0.84 14.0 17 19
4.0 40
50
34'
34'
4.0
4.3
0.67
0.72
0.77
0.83
4.0 2.8
3.4
275
344
10.4
10.4
0.91
0.98
15.1
16.3
17
18
20
21
30 36' 4.7 0.70 0.81 2.1 206 11.0 1.07 17.8 18 21
5.0 40 37' 5.0 0.70 0.81 5.0 2.8
3.4
275
344
11.3
11.3
1.14
1.20
18.9
20.1
18
19
21
22
50 37' 5.3 0.75 0.86
Note: All precipitation rates calculated for 180 degree operation. Note: All precipitation rates calculated for 180 degree operation.
For the precipitation rate for a 360 degree sprinkler, divide by 2. For the precipitation rate of a 360 degree sprinkler, divide by 2.
For more information on precipitation rates see page 105.
Data represented test results in zero wind. Adjust for local conditions. Radius may be reduced up to 25% with adjustment screw (this may alter the uniformity of spray pattern).
Optimum performance is shown in bold type.
For warranty information on Hunter Sprinklers, consult factory.