Pe's Cal

PROPOSED CONTINUED USE OF TEMPORARY 2-STOREY CONTAINER
CLASSROOMS WITH SHELTERED LINKWAY TO EXISTING EAST VIEW

PRIMARY SCHOOL ON LOT 06126N MK28 AT 4 TAMPINES TRESS 91
SINGAPORE 528907 (PAMPINES PLANNING AREA)
DESIGN CALCULATION
REF. NO: E2501-00024-2014-ST01
B K Ta n Co nsul t a nt s 510 Geylang Road #02-04 The Sunflower Singapore 389466

Tel: 67416021 Fax: 67415198 E-Mail:[email protected]
CONTENT PAGES
P.E. Standard Endorsement 01

Design Criteria 02
Structural Design 04
Structural Steel Frame 20
Structural Steel Staircase 25
P.E. Standard Endorsement 26

STANDARD CERTIFICATION ON STRUCTURAL PLANS AND DESIGN
CALCULATIONS BY THE QUALIFIED PERSON FOR STRUCTURAL WORKS
1. In accordance with Regulation 9 of the Building Control Regulations, I, Tan Bin Keong Qualified
Person For Structural Works appointed under section 8(1)(a) or 11(1)(d)(i) of the Building Control
Act, hereby submit the detailed structural plans and design calculations prepared by me and certify
that they have been prepared in accordance with the provisions of the Building Control Regulations,
the Building Control Act and any other written law pertaining to buildings and construction for the
time being force.
3. I further certify that these detailed structural plans and design calculations are in reference to Project
Ref No: E2501-00024-2014-ST01
4. Total number of structural plans submitted: 02

Total number of pages of design calculation in this book: 33
I, Tan Bin Keong, certify that the building works shown on these plans have been designed in accordance
with provisions of the Building Control Act 1989 and the Building Control Regulations 1989 subject to
the provisions of Section 14 of the Act.
___________________________________________________________________
(QUALIFIED PERSON FOR STRUCTURAL WORKS STAMP & SIGNATURE)
Date: 08/01/2015

DESIGN CRITERIA
A. Building Regulation & Design Codes

The following Codes have been used for the purpose of design:
BS 6399: Part 1: 1996 Design Loading for Buildings
SS CP65 Structural use of concrete
BS 8110: Structural use of concrete
BS 5950: Part 1: 2000 Structural Use of Steelwork in Buildings
SS CP4 code of practice for foundations
Building Control Regulation 2000
B. Design Loading
The following superimposed live loads obtained from BS6399: Part 3 in Section 4
1. Roof imposed load: 0.5 kN/m2

Wind load 0.35 kN/m2
Imposed load 2.5 kN/m2
2. Characteristic Dead Load
Reinforced Concrete 24 kN/m3
Steel 78 kN/m3
C. Design for Fire Resistance

The fire-rating of structural load-bearing members shall be 2 hours. Based on BS8110: 1985, the
minimum cover to the nearest reinforcement/ strand for the various elements are as follows:
Exposed to weather 30mm
1st Storey Floor Slab 25mm
2nd Storey to Roof 30mm
D. Material Standard & Specifications

a) Concrete
The minimum 28-day compressive cube strength of concrete for specified structural elements
shall be as follows:
Structural Components from 1st to Attic Storey = 30N/mm2
Structural Components contact with ground = 30N/mm2
Precast, prestressed hollow-core slabs = 45 N/mm2 (min)
Precast, prestressed beams = 45 N/mm2 (min)
b) Steel Reinforcement
Minimum yield strength of steel reinforcement shall be as follows:-
High Tensile Deformed Bar - fy = 460 N/mm2
Mild Steel Plain Bar - fy = 250 N/mm2
Welded Steel Fabric - fy = 485 N/mm2
c) Structural Steel

SS275JO BS EN 10025:1993
d) Bolts
All bolts shall be Grade 4.6 black bolts, unless otherwise stated.
e) Weld
Grade E43 electrodes fillet weld with design strength = 215 N/mm2 and full
penetration butt weld with design strength same as that of parent metal.
E. Deflection Criteria for steel member
1. Vertical Deflection (Gravity)
Cantilever beam (LL) < (Span)/180
Other beams (LL) < (Span)/200
2. Horizontal deflection
Column (LL+WL) < (height of column) /300
Column in portal frame (LL+DL) < (height of column) /1000
Column in portal frame (LL+WL) < (height of column) /1000
F. Analytical Software
Manual Calculations ATS STAAD Pro 2007 Spread Sheets

DESIGN CALCULATION

STRUCTURAL STEEL FRAME

Job No Sheet No Rev
1
Part
Software licensed to BKT
Job Title Ref
By Date18-Jun-14 Chd
Client File Date/Time 31-Mar-2015 16:05

EAST VIEW PRIMARY SCHOOL-plan.std
Job Information
Engineer Checked Approved
Name:
Date: 18-Jun-14
Structure Type PLANE FRAME
Number of Nodes 18 Highest Node 23

Number of Elements 26 Highest Beam 26
Number of Basic Load Cases 4

Number of Combination Load Cases 4
Included in this printout are data for:

All The Whole Structure
Included in this printout are results for load cases:

Type L/C Name
Primary 1 DL
Primary 2 LL
Primary 3 WL
Primary 4 WL1
Combination 5 1.4DL+1.6LL
Combination 6 1.2(DL+LL+WL)
Combination 7 1.2(DL+LL+WL1)
Combination 8 1.2DL+1.4WL1
Nodes
Node X Y Z
(m) (m) (m)
2 6.000 0.000 4.000
4 6.000 2.825 4.000
7 5.500 3.325 4.000
8 6.000 3.325 4.000
9 7.500 3.325 4.000
10 6.000 5.925 4.000
11 6.400 5.925 4.000
12 6.800 5.925 4.000
13 7.300 5.925 4.000
14 6.800 6.060 4.000
15 6.400 6.167 4.000
16 6.000 6.275 4.000
18 6.000 7.000 4.000
19 0.150 0.000 4.000
20 0.150 2.825 4.000
21 0.150 3.325 4.000
22 0.150 6.650 4.000
23 0.650 3.325 4.000
Print Time/Date: 31/03/2015 16:09 STAAD.Pro for Windows Release 2007 Print Run 1 of 11
Job No Sheet No Rev
2
Part
Job Title Ref

Beams
Beam Node A Node B Length Property
(m) (degrees)
1 19 20 2.825 1 0
2 2 4 2.825 1 0
3 20 21 0.500 1 0
4 20 23 0.707 5 0
5 4 7 0.707 5 0
6 4 8 0.500 1 0
7 9 4 1.581 4 0
8 23 21 0.500 2 0
9 23 7 4.850 3 0
10 7 8 0.500 2 0
11 9 8 1.500 8 0
12 10 8 2.600 1 0
13 21 22 3.325 1 0
14 11 10 0.400 7 0
15 11 12 0.400 7 0
16 12 13 0.500 7 0
17 11 14 0.422 7 0
18 14 12 0.135 7 0
19 14 13 0.518 7 0
20 10 15 0.468 7 0
21 15 11 0.242 7 0
22 16 10 0.350 1 0
23 15 14 0.414 7 0
24 16 15 0.414 7 0
25 16 18 0.725 1 0
26 18 22 5.860 6 0
Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 2C75X45X3 19.020 426.200 429.900 0.659 STEEL
2 2C300X98X3 32.580 659.800 4.42E 3 10.000 STEEL
3 2C300X98X3 32.580 659.800 4.42E 3 10.000 STEEL
4 TUB100503.0 8.540 36.800 110.000 88.400 STEEL
5 UA50X50X5 4.910 17.603 4.918 0.406 STEEL
6 RHS200X100X4 23.360 420.766 1.24E 3 969.978 STEEL
7 SHS38X38X3 4.200 8.638 8.638 12.863 STEEL
8 SHS100X100X3 11.640 182.709 182.709 273.802 STEEL
Job No Sheet No Rev
3
Part
Job Title Ref

Beam Loads : 1 DL
Beam Type Direction Fa Da Fb Db Ecc.
(m) (m)
8 UNI kN/m GY -4.800 - - - -
9 UNI kN/m GY -4.800 - - - -
10 UNI kN/m GY -4.800 - - - -
11 UNI kN/m GY -4.800 - - - -
23 UNI kN/m GY -0.400 - - - -
24 UNI kN/m GY -0.400 - - - -
26 UNI kN/m GY -0.750 - - - -
Selfweight : 1 DL
Direction Factor
Y -1.000
Beam Loads : 2 LL
(m) (m)
8 UNI kN/m GY -5.000 - - - -
9 UNI kN/m GY -5.000 - - - -
10 UNI kN/m GY -5.000 - - - -
11 UNI kN/m GY -5.000 - - - -
23 UNI kN/m GY -1.000 - - - -
24 UNI kN/m GY -1.000 - - - -
26 UNI kN/m GY -2.100 - - - -
Beam Loads : 3 WL
(m) (m)
19 UNI kN/m GY -0.700 - - - -
23 UNI kN/m GY -0.700 - - - -
24 UNI kN/m GY -0.700 - - - -
26 UNI kN/m GY -0.700 - - - -
Beam Loads : 4 WL1

(m) (m)
23 UNI kN/m GY 0.800 - - - -
24 UNI kN/m GY 0.800 - - - -
Job No Sheet No Rev
4
Part
Job Title Ref

Y
X
Z Load 3
Whole Structure
Y
X
Z Load 1
DL
Job No Sheet No Rev
5
Part
Job Title Ref

Y
X
Z Load 2
LL
Y
X
Z Load 3
WL
Job No Sheet No Rev
6
Part
Job Title Ref

18
16 15 14 13
12
10 11
22
9
8
7
4
23
21
20
Y
X
Z Load 3
19
Whole Structure
25
2220 171819
242123 16
26 14 15
12
11
13 10 7
56
8
3 4 2
1
Y
X
Z Load 3
Whole Structure
Job No Sheet No Rev
7
Part
Job Title Ref

25
2220 171819
242123 16
26 14 15
12
11
13 10 7
56
9
8
34 2
1
Y
X
Z Load 5 : Bending Z
MzLOAD CASE 5 1.4DL+1.6LL
Job No Sheet No Rev
8
Part
Job Title Ref

25
2220 171819
242123 16
26 14 15
12
11
13 10 7
56
9
8
34 2
1
Y
X
Z Load 5 : Shear Y
Fy LOAD CASE 5 1.4DL+1.6LL
Job No Sheet No Rev
9
Part
Job Title Ref

25
2220 171819
242123 16
26 14 15
12
11
13 10 7
56
9
8
34 2
1
Y
X
Z Load 5 : Axial Force
Fx LOAD CASE 5 1.4DL+1.6LL
Job No Sheet No Rev
10
Part
Job Title Ref

25
Max:
Max: 3.186
Max:
23
2421 mm
Max:
19Max:
Max:
3.155
3.183
16 mm 3.154
3.142
mm mm mm
26 2220
14 1518
17
Max:Max: 3.064
3.010 mm mm
Max: 7.236 mm Max: 2.977 mm
Max: 2.393 mm
12
Max: 1.687 mm
11
13 10 1.3017 mm
Max:
56
Max: 1.401 mm
9
Max: 4.539 mm Max: 1.599 mm
8 Max:
Max: 1.456
0.671 mm mm
3 4 2
Max: 0.999 mm
1
Y
X Load 2 : Displacement
Z Displacement - mm
Whole Structure Displacements LOAD CASE 2 LL
Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
Max FX 19 5:1.4DL+1.6LL 3.94 56.23 0.00 0.00 0.00 -3.97
Min FX 2 5:1.4DL+1.6LL -3.94 86.49 0.00 0.00 0.00 4.61
Max FY 2 5:1.4DL+1.6LL -3.94 86.49 0.00 0.00 0.00 4.61
Min FY 2 4:WL1 0.01 -0.71 0.00 0.00 0.00 -0.01
Max FZ 2 1:DL -1.37 27.39 0.00 0.00 0.00 1.60
Min FZ 2 1:DL -1.37 27.39 0.00 0.00 0.00 1.60
Max MX 2 1:DL -1.37 27.39 0.00 0.00 0.00 1.60
Min MX 2 1:DL -1.37 27.39 0.00 0.00 0.00 1.60
Max MY 2 1:DL -1.37 27.39 0.00 0.00 0.00 1.60
Min MY 2 1:DL -1.37 27.39 0.00 0.00 0.00 1.60
Max MZ 2 5:1.4DL+1.6LL -3.94 86.49 0.00 0.00 0.00 4.61
Min MZ 19 5:1.4DL+1.6LL 3.94 56.23 0.00 0.00 0.00 -3.97
Job No Sheet No Rev
11
Part
Job Title Ref

Failed Members
Beam AnalysisPropertyDesignProperty Ratio Clause L/C Ax Iz Iy Ix
(cm2) (cm4) (cm4) (cm4)
Utilization Ratio
Beam AnalysisPropertyDesignProperty Ratio Clause L/C Ax Iz Iy Ix
(cm2) (cm4) (cm4) (cm4)
1 2C75X45X3 2C75X45X3 0.373 BS-4.8.3.3.1 5 19.020 429.900 426.200 0.659
2 2C75X45X3 2C75X45X3 0.432 BS-4.8.3.3.1 5 19.020 429.900 426.200 0.659
3 2C75X45X3 2C75X45X3 0.292 BS-4.8.3.2 5 19.020 429.900 426.200 0.659
4 UA50X50X5 UA50X50X5 0.477 BS-4.8.3.3.1 5 4.910 4.506 18.015 0.409
5 UA50X50X5 UA50X50X5 0.785 BS-4.8.3.3.1 5 4.910 4.506 18.015 0.409
6 2C75X45X3 2C75X45X3 0.278 BS-4.8.3.2 5 19.020 429.900 426.200 0.659
7 TUB100503.0 TUB100503.0 0.140 BS-4.7 (C) 5 8.540 110.000 36.800 88.400
8 2C300X98X3 2C300X98X3 0.142 BS-4.8.2.2 5 32.580 4.42E 3 659.800 10.000
9 2C300X98X3 2C300X98X3 0.973 BS-4.3.6 5 32.580 4.42E 3 659.800 10.000
10 2C300X98X3 2C300X98X3 0.288 BS-4.8.2.2 5 32.580 4.42E 3 659.800 10.000
11 SHS100X100X3 SHS100X100X3 0.491 BS-4.8.2.2 5 11.640 182.709 182.709 273.802
12 2C75X45X3 2C75X45X3 0.322 BS-4.8.3.3.1 5 19.020 429.900 426.200 0.659
13 2C75X45X3 2C75X45X3 0.299 BS-4.8.3.3.1 5 19.020 429.900 426.200 0.659
14 SHS38X38X3 SHS38X38X3 0.074 BS-4.8.3.3.3 6 4.200 8.638 8.638 12.863
15 SHS38X38X3 SHS38X38X3 0.017 BS-4.8.3.3.3 6 4.200 8.638 8.638 12.863
16 SHS38X38X3 SHS38X38X3 0.011 BS-4.8.3.3.3 6 4.200 8.638 8.638 12.863
17 SHS38X38X3 SHS38X38X3 0.022 BS-4.8.3.3.3 6 4.200 8.638 8.638 12.863
18 SHS38X38X3 SHS38X38X3 0.009 ANNEX I.1 6 4.200 8.638 8.638 12.863
19 SHS38X38X3 SHS38X38X3 0.025 BS-4.8.2.2 6 4.200 8.638 8.638 12.863
BKTAN CONSULTANTS
PROJECT EAST VIEW PRIMARY SCHOOL
Designed by: Date:
CLIENT CPG TRANG 3/31/2015
CODE BS 5950 - PART 1: 2000 Checked by: Revision:
JOB PURLIN DESIGN BKT 1
STATUS DESIGN: VALID DESIGN
Structural diagram: Fixed at two supports Span: Lmax= 4.5 m
Load span: 0.915 m
Loading calculation: kN/m3
Case DL LL WL Unit Roof material: steel = 78
Selfweight 0.09 kN/m Thickness: 0.47 (mm)
Uniform load UDL 0.4575 0.3203 kN/m Steel grade: S275
2
Total UDL 0.09 0.4575 0.3203 kN/m py= 275 N/mm
Factored load 1.4DL+1.6LL = 0.858 kN/m

Determine internal force: Mmax= 1.45 kNm
Vmax= 1.93 kN
Deflection = 2.41 mm
Section: 532
100x50x20x5.18xkg/m LIPPED CHANNEL
2 3
Section property: A= 6.53 cm ry= 1.87 cm Zx= 19.8 cm
4 3
Ix-x= 99 cm x= 33.1 Zy= 7.27 cm
4
Iy-y= 22.9 cm u= 0.781
3
Sx= 23.6 cm Selfweight= 5.18 kg/m
3 2
Sy= 11.6 cm E= 205 kN/mm
Checking: Flexure checking Shear checking Deflection checking

Mc=py*S= 6.49 kNm Pv=0.6pyAv= 107.7 kN a= L/200= 22.5 mm
Mc > Mmax Pv > Vmax < a
Satisfied Satisfied Satisfied
Zp= WpL/1800= 1.4 < Zx Satisfied

Zq= WqL/2250= 0.5 < Zx Satisfied
Lateral torsional buckling:

Checking lateral torsional buckling
LT= uvw1/2 = 123.0
With: LE= 0.85L= 3.825 m = LE/ry= 204.5
N= /x= 6.178 w= 1.0
1
v= = 0.77
(1+0.05N2)0.25
mLT= 0.925 (From table 18 BS 5950-1 2000)
2
=> pb = 92.4 N/mm (From table 16 BS 5950-1 2000)
Mb = 2.18 kNm
mLTMu= 1.34 kNm
Mb > mLTMu Satisfied
BKTAN CONSULTANTS
Designed by: Date:
JOB WELD DESIGN BKT 1
Position of weld connection: COLUMN - BASE PLATE

Material capacity: Grade of parent steel: S275
Electrode classification: 35
2
Design strength of fillet weld pw(N/mm ): 215 N/mm2
Iu= 984375 mm4
Wu= 13125.0 mm3
Length of weld L= 375 mm
Thickness of weld s= 3 mm
Internal force:
From staad pro Mu= 4.6 kN.m Vu= 3.9 kN
Node 2
Design weld:
FS due to shear force Vu: Fs=Vu/L= 10.4 N/mm
FT due to moment Mu: FT=Mu/W= 350.5 N/mm
Resultant stress: FR=(Fs2+FT2)1/2= 350.7 N/mm
CHECK FOR 3mm WELD SIZE

PL=0.7spw= 451.5 N/mm > FR Satisfied
BKTAN CONSULTANTS
Designed by: Date:
JOB BOLT DESIGN BKT 1
Position of bolt connection: Column-Base plate

Material capacity: Grade of plate steel: S275
Bolt size (): 16 Grade 8.8
Design strength of bolt(N/mm2): ps= 375 N/mm2
2
pt= 560 N/mm
2
pbb= 1000 N/mm
Total nos. of bolts= 4 nos. in 2 rows 2 col.s
Spacing in direction of major stress= 150 mm
Spacing in direction of minor stress= 140 mm
Plate size LxBxt= 250 x 200 x 25 mm
End distance= 30 mm
Bolts in tension: 4 nos.
Bolts in shear: 4 nos.
Internal force:
M= 4.6 kN.m V= 3.9 kN
Determine:
Shear stress due to direct shear
Fs= V = 0.98 kN
No. of bolts
Tension stress due to bending moment:
M.ymax
FT = = 15.33 kN
y2i
Design bolts connection:
Shear capacity Ps of a bolt: Ps=psAs= 75.4 kN
Tension capacity Pt of a bolt: Pt=0.8ptAt= 71.16 kN
Check for combine shear and tension:

Fs FT
+ <= 1.4
Ps Pt
<=> 0.23 < 1.4 Satisfied
BKTAN CONSULTANTS
Designed by: Date:
Position of weld connection: DETAIL B

Design strength of fillet weld pw(N/mm2): 215 N/mm2
Iu= 4500000.00 mm4
Wu= 30000.0 mm3
Internal force:
Mu= 12.7 kN.m Vu= 8.1 kN
Design weld:

BKTAN CONSULTANTS
Designed by: Date:
Position of weld connection: DETAIL A

Design strength of fillet weld pw(N/mm2): 215 N/mm2
Iu= 2333333.33 mm4
Wu= 23333.3 mm3
Internal force:
Mu= 9.3 kN.m Vu= 13.9 kN
Design weld:

BKTAN CONSULTANTS
Designed by: Date:
Position of weld connection: DETAIL B (100x100x3SHS-COLUMN)

2
Design strength of fillet weld pw(N/mm ): 215 N/mm2
Iu= 18000000.00 mm4
Wu= 60000.0 mm3
Internal force:
Mu= 4.8 kN.m Vu= 14 kN
Design weld:
FT due to moment Mu: FT=Mu/W= 80 N/mm

BKTAN CONSULTANTS
Designed by: Date:
JOB BOLT DESIGN (detail A) BKT 1
Position of bolt connection: DETAIL A

Material capacity: Grade of plate steel: S275
Bolt size (): 16 Grade 8.8
Design strength of bolt(N/mm2): ps= 375 N/mm2
pt= 560 N/mm2
2
pbb= 1000 N/mm
Total nos. of bolts= 4 nos. in 2 rows 2 col.s
Spacing in direction of major stress= 140 mm
Spacing in direction of minor stress= 160 mm
Bolts in tension: 4 nos.
Bolts in shear: 4 nos.
Internal force:
M= 9.3 kN.m H= 14 kN
Determine:
Shear stress due to direct shear
H
Fs= = 3.5 kN
No. of bolts
Tension stress due to bending moment:
M.ymax
FT = = 33.21 kN
y2i
Design bolts connection:
Shear capacity Ps of a bolt: Ps=psAs= 75.4 kN
Tension capacity Pt of a bolt: Pt=0.8ptAt= 71.16 kN
Check for combine shear and tension:

Fs FT
+ <= 1.4
Ps Pt
<=> 0.5 < 1.4 Satisfied
BKTAN CONSULTANTS
PROJECT EAST WIEW PRIMARY SCHOOL
Designed by: Date:
CODE BS8110:1997 Checked by: Revision:
JOB PUNCHING SHEAR CHECKING BKT 1
Punching shear analysis:

RC footing pad 350mm thick, d=300mm, is constructed with grade 30 concrete and
is reinforced with 7mm bars at 200mm centres one way and 7mm bars at
200mm centres in the other direction. Determine the maximum load that can
be carried on an area 250xmm, without exceeding the ultimate shear stress:
Take 1m width of slab band to analysis:

b= 200 mm d= 300 mm
a= 250 mm
fcu= 30 N/mm2
R 7 Spacing: 200 R 7 Spacing: 200
For R7-200 reinforcement
100As/(bd)= 100x3.14x3.5x3.5x(1000/200)/(200x300)= 0.32
For R7-200 reinforcement
100As/(bd)= 100x3.14x3.5x3.5x(1000/200)/(200x300)= 0.32
Average 100As/(bd)= (0.32+0.32)/2= 0.32

From table, c= 0.48 N/mm 2
Punch shear perimeter:

2a+b+6d= 2x250+200+6x300= 2500 mm
maximum load N=c x perimeter x d= 360000 N= 360 kN > 86.5 kN
Satisfied
At the face of loaded area, the shear stress:
=N/((2a+2b)d)= 360000/((2x250+2x200)x300)= 1.33 N/mm2
which is less than 0.8fcu1/2= 4.38 N/mm2 and 5.0 N/mm2 Satisfied
Table: Value of ultimate shear stress c (N/mm2) for a concrete strength of fcu=30N/mm2
Effective depth (mm)
100As/(bd) 150 175 200 225 250 300 >=400
<=0.15 0.46 0.44 0.43 0.41 0.40 0.38 0.36
0.25 0.54 0.52 0.50 0.49 0.48 0.46 0.42
0.50 0.68 0.66 0.64 0.62 0.59 0.57 0.53
0.75 0.76 0.75 0.72 0.70 0.69 0.64 0.61
1.00 0.86 0.83 0.80 0.78 0.75 0.72 0.67
1.50 0.98 0.95 0.91 0.88 0.86 0.83 0.76
2.00 1.08 1.04 1.01 0.97 0.95 0.91 0.85
>=3.00 1.23 1.19 1.15 1.11 1.08 1.04 0.97
For characteristic strengths other than 30N/mm2 the values in the table multiplied by
(fcu/25)1/3/1.06, the value of fcu should not be greater than 40N/mm2
STANDARD CERTIFICATION ON STRUCTURAL PLANS AND DESIGN
CALCULATIONS BY THE QUALIFIED PERSON FOR STRUCTURAL WORKS
1. In accordance with Regulation 9 of the Building Control Regulations, I, Tan Bin Keong Qualified
Person For Structural Works appointed under section 8(1)(a) or 11(1)(d)(i) of the Building Control
Act, hereby submit the detailed structural plans and design calculations prepared by me and certify
that they have been prepared in accordance with the provisions of the Building Control Regulations,
the Building Control Act and any other written law pertaining to buildings and construction for the
time being force.
3. I further certify that these detailed structural plans and design calculations are in reference to Project
Ref No: E2501-00024-2014-ST01
4. Total number of structural plans submitted: 02

Total number of pages of design calculation in this book: 33
I, Tan Bin Keong, certify that the building works shown on these plans have been designed in accordance
with provisions of the Building Control Act 1989 and the Building Control Regulations 1989 subject to
the provisions of Section 14 of the Act.
___________________________________________________________________
(QUALIFIED PERSON FOR STRUCTURAL WORKS STAMP & SIGNATURE)
Date: 08/01/2015


Pe's Cal

Uploaded by

Copyright:

Available Formats

Pe's Cal

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pe's Cal

Uploaded by

Copyright:

Available Formats

PROPOSED CONTINUED USE OF TEMPORARY 2-STOREY CONTAINER

CLASSROOMS WITH SHELTERED LINKWAY TO EXISTING EAST VIEW

B K Ta n Co nsul t a nt s 510 Geylang Road #02-04 The Sunflower Singapore 389466

P.E. Standard Endorsement 01

B K Ta n Co nsul t a nt s 510 Geylang Road #02-04 The Sunflower Singapore 389466

4. Total number of structural plans submitted: 02

B K Ta n Co nsul t a nt s 510 Geylang Road #02-04 The Sunflower Singapore 389466

A. Building Regulation & Design Codes

1. Roof imposed load: 0.5 kN/m2

C. Design for Fire Resistance

D. Material Standard & Specifications

B K Ta n Co nsul t a nt s 510 Geylang Road #02-04 The Sunflower Singapore 389466

B K Ta n Co nsul t a nt s 510 Geylang Road #02-04 The Sunflower Singapore 389466

B K Ta n Co nsul t a nt s 510 Geylang Road #02-04 The Sunflower Singapore 389466

STRUCTURAL STEEL FRAME

B K Ta n Co nsul t a nt s 510 Geylang Road #02-04 The Sunflower Singapore 389466

Client File Date/Time 31-Mar-2015 16:05

Structure Type PLANE FRAME

Number of Nodes 18 Highest Node 23

Number of Basic Load Cases 4

Included in this printout are data for:

Included in this printout are results for load cases:

Client File Date/Time 31-Mar-2015 16:05

Client File Date/Time 31-Mar-2015 16:05

Beam Loads : 4 WL1

Client File Date/Time 31-Mar-2015 16:05

Client File Date/Time 31-Mar-2015 16:05

Client File Date/Time 31-Mar-2015 16:05

Client File Date/Time 31-Mar-2015 16:05

MzLOAD CASE 5 1.4DL+1.6LL

Client File Date/Time 31-Mar-2015 16:05

Fy LOAD CASE 5 1.4DL+1.6LL

Client File Date/Time 31-Mar-2015 16:05

Fx LOAD CASE 5 1.4DL+1.6LL

Client File Date/Time 31-Mar-2015 16:05

Whole Structure Displacements LOAD CASE 2 LL

Client File Date/Time 31-Mar-2015 16:05

Factored load 1.4DL+1.6LL = 0.858 kN/m

Checking: Flexure checking Shear checking Deflection checking

Zp= WpL/1800= 1.4 < Zx Satisfied

Lateral torsional buckling:

STATUS DESIGN: VALID DESIGN

Position of weld connection: COLUMN - BASE PLATE

FT due to moment Mu: FT=Mu/W= 350.5 N/mm

Resultant stress: FR=(Fs2+FT2)1/2= 350.7 N/mm

CHECK FOR 3mm WELD SIZE

STATUS DESIGN: VALID DESIGN

Position of bolt connection: Column-Base plate

Tension capacity Pt of a bolt: Pt=0.8ptAt= 71.16 kN

Check for combine shear and tension:

STATUS DESIGN: VALID DESIGN

Position of weld connection: DETAIL B

FT due to moment Mu: FT=Mu/W= 423.3 N/mm

Resultant stress: FR=(Fs2+FT2)1/2= 423.5 N/mm

CHECK FOR 3mm WELD SIZE

STATUS DESIGN: VALID DESIGN

Position of weld connection: DETAIL A

FT due to moment Mu: FT=Mu/W= 398.6 N/mm