WheatFromFieldToFlour PDF
WheatFromFieldToFlour PDF
WheatFromFieldToFlour PDF
TABLE OF CONTENTS
Introduction .............................................................................................. 1
Milling...................................................................................................... 22
REFERENCES ......................................................................................................................... 36
I
Wheat: From Field to Flour
Funding for this publication is supported by the Nebraska Wheat Board. Much of this information was gathered
from a variety of offices supported by the Nebraska Wheat Board. Information in this text is designed as a supple-
ment to agricultural education and is subject to change without notification.
Use of this publication is at the discretion of each individual. Reproduction of this publication by photocopy,
email, fax, and other electronic forms of reproduction is permissible.
Thank you to our constituents for providing the original sources of information used in producing this publication.
This information was compiled by Cody Dvorak, 2008-2009 Nebraska Wheat Board intern.
May 8, 2009
II
INTRODUCTION
Wheat flour is one of the most nutritious plant foods available, offering an array of minerals and critical nutrients.
Per capita consumption of wheat in the United States exceeds that of any other single food staple; however, not all
wheat is equal. There are many types, varieties and different properties to the different grains. Wheat is classified
into six classes (classes are described on page 6) and over 30,000 varieties. Wheat is not only used to make food
but it is also a component of glue, paper and pet food, among other products. Wheat is one of the most important
foods to the United States in terms of health as well as the economy. It is a staple in most Americans diets and
has properties that cant be replaced by other cereal grains.
Over 17,000 years ago, humans gathered and ate plant seeds. At this time they discovered the berry of the wheat
plant was edible. Around 8,000 years ago, Swiss lake dwellers ground and mixed early wheat with water, then
baked it to make unleavened cakes or bread. The Egyptians were the first to discover leavened bread over 5,000
years ago. Today, we still eat the wheat berry but unlike 17,000 years ago, we eat a refined product of wheat rather
than chewing on raw kernels.
The top five producing countries of the worlds total wheat supply in 2005-06 were:
1. China 15.4 percent (of world supply)
2. India 11.5 percent
3. United States 9.1percent
4. Russia 7.3 percent
5. France 5.9 percent
In 2008, the United States produced 2.5 billion bushels of wheat. Harvested area of land totaled 55.7 million acres
resulting in an average yield of 44.9 bushels/acre. The top wheat producing states (in order of production) in 2008
were Kansas, North Dakota, South Dakota, Oklahoma and Montana.
In 2008, Nebraska ranked 12th in total wheat production and ninth in total winter wheat production. All of Ne-
braska wheat is winter wheat of which 98 percent is Hard Red Winter (HRW) and 2 percent is Hard White (HW).
Production in 2008 totaled 73.5 million bushels with an average yield of 44 bushels/acre.
1
2
3
PARTS OF THE
WHEAT PLANT
kernel
awn/beard
head
leaves
main stem
7. tiller
roots
4
WHEAT GROWTH STAGES
(FEEKES SYSTEM)
Being able to determine the growth stage of wheat is important in deciding cultural practices during the duration of the
plant. Fertilizers, pesticides, and other chemicals should or should not be applied at certain points during the plants
life. By understanding what stage the plant is in, producers can determine the correct cultural practices.
There are many methods used today to determine the stage of wheat but the most commonly used system is the
Feekes System shown below.
5
Vegetative growth in the tillering stage is determined by tillers present as shown here. Many
tillers are formed, and formation may be interrupted or completed prior to the onset of winter.
(2.0)
Wheat Growth Stages
L3 Tiller nomenclature
Third tiller (T3)
L2
Main Stem (MS)
Flag Leaf
node
internode
node
Leaf Sheath
Head forming
6
Wheat Reproductive Growth
The final stage of vegetative growth is spike
StagesThe flowering
Feekes Scale
stage begins once the anthers
emergence. This occurs when the head is fully emerge.
emerged from the stem. After this takes place, (10.5.1)
the plant starts reproductive growth. Wheat is 10.1 to 10.5 Spike emergence
self-pollinating.
(10.5) 10.5 to 11.0 Flowering
Anther
Immediately following emergence of all anthers, Wheat is ready to harvest when pressure from ones
the ripening stage starts. The ovaries are polli- thumb applied to the kernel does not create a dent. This
nated and the seed begins to mature. means that the grain is physiologically mature and has
(11.0) lost enough moisture to be harvested and stored.
7
CLASSES OF WHEAT
There are six market classes of wheat grown in the United States. Within the six classes, there are over 30,000 varieties.
The six classes are categorized according to hardness, color and growing season.
Each class is produced in a specific area of the United States due to its specifications for climate, soil type and topogra-
phy. Each class also has its own unique milling characteristics, making each class unique for specific uses in baking or
other food uses.
The major wheat classes in Nebraska are Hard Red Winter and Hard White. Hard White Wheat accounts for about 1.9
percent of the total production in Nebraska and continues to rise.
HRW wheat has good characteristics for milling and baking. The ma- HRS wheat is another important bread wheat. It maintains the highest
jority of HRW wheat is produced in the Great Plains states between protein content of all the classes, usually 13-14%. It is primarily grown
the Mississippi River and Rocky Mountains as well as significant in the north central United States and has good milling and baking
amounts in California. HRW wheat has a significant amount of pro- characteristics. Primary producers are North Dakota, South Dakota,
tein and is typically used in breads, rolls, all purpose flour, and some Minnesota, and Montana.
sweet goods.
8
As the map shows, not every class of wheat is grown everywhere. Each class has its own specifications and re-
quirements to produce optimally. Some wheat requires a certain amount of moisture. Others require a specific
temperature range. Some wheat requires a specific type of soil to grow in. And certain classes have specific grow-
ing seasons very different from other classes.
Geography and climate indicate what type of wheat can be grown in a specific area. Even though wheat is a versa-
tile grain with six classes suited to different growing conditions, there are parts of the country not well suited for
growth. These areas may not have temperatures and/or rainfall required for proper growth of the crop or they may
have soils better suited to other types of production agriculture.
9
WHEAT PRODUCTS
cosmetics
pet food
paper
Carry-out containers
body/laundry soap & shampoo
10
RAISING WHEAT
The six classes of wheat and their thousands of varieties make wheat suitable to various climates in vast areas of
the world. Each class and variety has its own unique specifications for temperatures, elevation and water require-
ments, but there is also much diversity within the classes. More of the worlds surface is covered by wheat than
any other food staple. Wheat can be grown all the way from the Arctic Circle to the equator, at sea level or on roll-
ing, high-altitude slopes. In fact, somewhere in the world, wheat is being harvested every month of the year.
Spring wheat planted just before or during April. Spring wheat grows throughout the spring and summer
months and is usually harvested around the beginning of August.
Winter wheat planted just before September in the Northern United States and continues through October in the
Southern regions. After planting, the seed will grow into a plant and continue to go through the tillering stage, but
will not joint before reaching a cool point known as vernalization.
Vernalization is a necessary process all winter wheat varieties go through. The wheat must submit to a
certain amount of cool temperatures before it joints and flowers. The optimum temperature for vernaliza-
tion of winter wheat is between 40F and 50F; not around freezing temperatures, contrary to popular be-
lief. Winter wheat can be submitted to temperatures so cold that the plant undergoes a process called
winterkill. For this reason, a layer of snow is often desired on the topsoil to act as an insulation between
the soil and the air. Under normal field conditions, eight to 12 weeks of growth is usually required before
vernalization temperatures set in for the full development of winter hardiness.
Wheat did not originally have a winter adaption process. Through evolution, wheat has developed adaptive
mechanisms to cool temperatures. After winter hardening, wheat can reverse its dormancy when the
weather becomes warm again. Cold acclimation of winter wheat begins once fall crown temperatures drop
below 48F. Likewise, in the spring, when crown temperatures rise above 48F, winter wheat dehardens.
The crown temperature is different from the air temperature because soil holds a certain amount of cold/
warmth after air temperatures considerably change. The crown of the wheat plant remains below the soil
surface and takes on the temperature of the soil rather than the temperature of the air. Therefore, several
weeks of cold/warm air temperatures are required to cool/warm the crown of the wheat plant to a tempera-
ture similar to the air.
Durum Durum is a spring-seeded wheat, harvested in late July or early August. It is milled into high-protein
semolina flour used to make high-quality pasta products such as macaroni and spaghetti.
11
TILLING AND PLANTING
The method of planting wheat has greatly evolved over the years. Humanity went from seeding crops by hand to
using horses or oxen to make the job easier. Through the years, humans have developed more and more sophisti-
cated machinery to pull the plows and planters required to seed crops, including wheat. Now, tractors can be
guided by GPS or Global Positioning System that literally steers the tractor by utilizing a complex set of satellites
orbiting the earth in space.
Wheat like most other crops can be planted in either tilled soil or in minimum/no-till soil. Tilled soil means the
previous crop in that field is plowed or disked under to create looser, more arid soil.
Minimum and no-till practices save on fuel and help minimize soil erosion. Soil conservation is very important so
a farmer can continue to use the same piece of land, year after year and generation after generation. If too much
topsoil is lost due to erosion, it will become infertile and be very difficult to revert into good farming ground again.
On the other hand, planting wheat into untilled soil may result in increased insect and plant disease problems left
from the previous crop.
Wheat planted into old crop residue Tractor pulling a disk through a field of wheat
Another practice producers may choose to utilize is referred to leaving a field fallow or unplanted for a year. Fal-
low fields are usually in a rotation with other fields, creating an every-other-year harvest on that particular field.
Leaving a field unplanted for one year stores moisture in dry regions as long as the farmer makes sure the field
remains weedless.
Wheat may be utilized as pasture in the Great Plains of Texas, Oklahoma, and southern Kansas. Winter wheat
classes can be grazed either before winter, during early winter or in early spring. Wheat can be grazed between the
6 inch height and jointing stage, after which grazing should be ceased in order to attain a grain crop. Grazing at
this point will cause significant depletion of the grain harvest yield. If there is no intention of harvesting the wheat
field for grain, it may be grazed for a longer period of time. Each individual farmer determines whether the re-
duced grain yield/no yield is profitable for their operation. This decision can fluctuate from year to year, depend-
ing upon the price of wheat versus beef cattle prices.
Air seeder
Grain Drill
12
HARVEST
Wheat begins to ripen in the southern United States in late May, progressing northward throughout the summer
until spring wheat is harvested near the Canadian border after August first.
Just as the procedures to plant wheat have evolved over the years, so have the harvesting methods. Over four thou-
sand years ago a sickle and scythe were used to cut the grain. This process was very time consuming and labor
intensive.
Reaping
The reaper was developed in 1830 by a Virginia farmer, Cyrus McCormick. The machine was designed to cut the
wheat at a specific height then men gathered the bundles into sheaves. Eventually the reaper was designed to bun-
dle the sheaves itself. After the sheaves were bundled they were gathered by the reaper and the grain was flailed
(beat) off the chaff (stems).
Threshing
Threshing, or thrashing in earlier days was designed to beat the grain off the wheat stems. This process was called
flailing. In the days before 1770, farmers laid their cut wheat and other cereal crops on the floor of a barn to be
flailed by farm animals. This worked easier than the alternative but left the clean grain dirty and full of rocks
and animal manure which decreased the market value. The alternative to this was to beat the head of the stalk with
a club like tool to loosen the grain, then throw it into the air. The lighter chaff material blew away further on the
ground than the grain which was heavier. The grain was then collected and sold at the local mill.
The first recorded attempt at developing a threshing machine was in 1770 by a Pennsylvania farmer, John Clayton
and again in 1782 by another Pennsylvania farmer, Colonel Anderson. Both of these machines were horse pow-
ered. Throughout the years the thresher was improved and remodeled until it no longer required horses, then was
combined with the reaper and winnower (cleaner) to create the first combine.
The Combine
The first combine (stripper-harvester) was developed in 1884 by James Morrow of Victoria, Australia. The fol-
lowing year Hugh Victor McKay, also of Victoria, unveiled his version of a stripper-harvester. Morrow received a
Victorian Government Prize for his invention but it was McKays version that went on to be widely distributed.
Today McKay is considered the inventor of the modern combine. The development of a large scale manufacturing
facility, Sunshine Harvester, in Victoria facilitated the popularity of McKays machine.
In the United States, the idea of the combine didnt really catch on until shortly after World War I (1918). Today,
an acre of wheat can be harvested in about thirty minutes. Thanks to the development of the combine and other
helpful farm machinery, thirty-two acres of wheat can now be planted and harvested with the same amount of labor
once used for one acre.
The combine cuts the wheat, threshes the grain, separates the large particles of chaff out of the grain and stores the
grain in a large hopper on the combine or unloads directly to a grain cart pulled by a tractor, then onto a semi truck
for transport to the local elevator or to the farmers private bins for storage to be sold at a later time.
Hopper
Auger (arm)
13
Head Cab
PLANTING AND HARVEST DATES
WHEAT JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC
HRW Planting
HRW Harvest
HRS Planting
HRS Harvest
SRW Planting
SRW Harvest
SW Planting
SW Harvest
HW Planting
HW Harvest
Durum Planting
Durum Harvest
14
THE MARKET
After the farmers grain is harvested he will either immediately truck the grain to a country elevator near the farm or
store it in his own bins to sell at a later time. The reason for doing this is because the farmer is expecting a better
price for the grain in the future. The name for the large storage facility, the elevator, is because of the moving belts
used inside to move, or elevate, the grain. The grain is purchased by the elevators manager, often acting on
behalf of a cooperative group of farmers. The wheat, whether stored at the farm or elevator, is kept in a tempera-
ture and humidity controlled environment to prevent spoilage and insect growth.
Wheat should ideally be at or below 14% moisture when harvested. If not, it is placed in special equipment called
a dryer to dry. The farmer or elevator manager may either sell or hold the grain for future sale watching the market
for a better price.
GRAIN INSPECTION
The U.S. Department of Agriculture can do an official inspection of a ship-
ment of wheat at any point in the marketing of grain. The farmer will either
submit a sample or a U.S.D.A. service representative will take an official
sample to record the wheat class, protein, moisture, and percentage of non-
wheat material in the sample.
GRAIN SALE
The sale of wheat may be either for ex-
port or domestic use. Approximately half
Grain Dryer of the United States wheat production is
sold through both markets each year. If
the wheat is sold for domestic use, it is frequently sold at a grain exchange.
A grain exchange is where U.S. grain buyers and sellers meet. The largest ex-
changes are located in Chicago, Kansas City, and Minneapolis. The grain ex-
change itself does not buy or sell. Its members represent either the individuals
and companies that sell grain or the buyers, i.e., millers, brewers, feed manufac-
turers and exporters. They will buy on either a cash basis, in which the grain is
delivered immediately, or on a futures basis for a guaranteed price at a future Country Grain Elevator
delivery date.
Once the grain is sold, it is transported to a terminal elevator for movement to the buyer. Trucks, rail cars, barges
and ships are all part of this system.
When the grain is finally delivered, it will probably be to a mill, either in the United States or abroad.
15
16
17
WHY EAT WHEAT?
Wheat is one of the most important foods in a balanced diet. In general people starting at the age of 14 should con-
sume approximately 6-7 ounces of grains per day, half of which should come from whole grains. Specific amounts
with regard to age and gender can be found at http://mypyramid.gov. One ounce of grain, in general, is equal to
one slice of bread, one cup of ready-to-eat cereal, or one-half cup of cooked rice, pasta, or cooked cereal.
Wheat is primarily made up of complex carbohydrates which provide a source of time-released energy. The nu-
trition community recommends that 55-60 percent of our daily calories come from carbohydrates. Also, no more
than 30 percent of our calories should come form fat, and approximately 12-15 percent of calories should be de-
rived from protein. Clearly, calories acquired from carbohydrates such as wheat products are the healthiest and
most important to incorporate in our diets.
Complex carbohydrates provide essential nutrients, are less likely to be stored as fat and more likely to be stored as
muscle fuel.
So, whats in wheat that makes it so healthy? One major component in wheat which is only found in plant foods is
dietary fiber. Dietary fiber is the carbohydrate in food which humans cannot digest. Fiber acts as a broom to
sweep out the digestive tract as well as satisfying appetite longer. One slice of whole wheat bread contains 2
grams of dietary fiber; one slice of white bread contains 0.5 grams; and one ounce of wheat bran cereal contains
between 8 and 9 grams of dietary fiber. The American Dietetic Association recommends eating 20-35 grams of
fiber each day, but on average, Americans currently only consume about 12 grams of dietary fiber per day.
18
WHEAT FOODS PROVIDE...
Thiamin (B1)- Needed daily for good appetite, digestion, and healthy nerves. It also helps the body make better
use of fat and carbohydrates.
Riboflavin (B2)- This vitamin is essential for the use of protein by the body.
Niacin (B3)- This is the anti-pellagra vitamin. Pellagra is a nutrient deficient disease that has been virtually
eliminated since the enrichment of white flour products began in the 1940s.
Iron Iron is essential for providing our bodies with energy. Iron acts in this way by carrying oxygen from the
lungs to muscles and other parts of the body. A deficiency of iron causes a disease known as anemia which results
in a lack of energy.
Protein Wheat foods provide 2-4 grams of protein per one ounce serving. Six to seven ounces of protein per day
are required for the average teenager and adult. Protein is an important component of every cell in the body. Hair
and nails are mostly made of protein. Your body uses protein to build and repair tissues. You also use protein to
make enzymes, hormones, and other body chemicals. Protein is an important building block of bones, muscles,
cartilage, skin, and blood.
Insoluble fiber Found in wheat bran and whole grains, insoluble fiber passes through the digestive system
quickly, promoting regularity and reducing the risk of colon irregularities or diverticulosus, a type of colon disease.
Research suggests foods containing insoluble fiber may also help reduce the risk of colon and breast cancer when
part of a low-fat diet.
Soluble fiber Found in oats, beans, some fruits and vegetables and refined white flour products. Studies indicate
foods containing soluble fiber may help decrease blood pressure and cholesterol levels, helping to reduce the risk
of heart disease. They may also help control blood sugar levels in people with diabetes.
Percentages of Protein
in Wheat End Products
Whole wheat bread 16.25
Hearth bread 15.5
Macaroni & egg noodles (U.S.) 15
White bread 14
All purpose flour 12.5
Crackers 11.25
Pie crust & doughnuts 10.5
Noodles (oriental) 10.5
Cookies 9.75
Cake 9.5
0 2 4 6 8 10 12 14 16 18
19
20
WHEAT FLOUR
Wheat flour is the most important ingredient in home baking and is the framework for almost every commercially
baked product and pasta. Of the grains available for the production of flour, wheat is unique. It is the only cereal
grain with sufficient gluten content to make a typical loaf of bread without being mixed with other grains. For
example, for one to make rye bread a certain amount of wheat flour is usually present in the end product. Breads
can be made without wheat flour but they are rather rare because the bread will not rise as high and therefore will
be very dense.
All-purpose flour is a product of the ground endosperm Gluten flour is processed from high protein wheat. It is
of hard wheat or a combination of hard and soft wheat used by bakers in combination with low protein or non-
kernels. wheat flours. The increased amount of gluten improves
baking quality and produces yeast breads of high protein
Enriched all-purpose flour has iron and B-vitamins content.
(thiamine, niacin, and riboflavin) added in amounts
equal to or exceeding that in whole wheat flour. Semolina is the coarsely ground endosperm of durum
wheat. It is high in protein and is used to create high
Bleached all-purpose flour is exposed to chlorine gas or quality pasta products such as macaroni and spaghetti.
benzoyl peroxide to whiten and brighten flour color.
Chlorine also affects baking quality by maturing or Durum flour is a by-product in the production of semo-
oxidizing the flour, which is beneficial for cake and lina and is used for American noodles, some types of
cookie baking. The bleaching agents react and do not pasta and occasionally in specialty breads.
leave harmful residues or destroy nu-
trients. Farina is the coarsely ground en-
dosperm of durum. It is used to make
Unbleached all-purpose flour is hot breakfast cereals, most commonly
bleached by oxygen in the air during known as Cream of Wheat or Malt-
an aging process and is off-white in O-Meal.
color. Nutritionally, bleached and
unbleached flour are equivalent. Whole wheat flour is flour produced
from the entire berry of wheat. It in-
Bread flour is ground form the en- cludes coarsely ground bran and germ
dosperm of the hard red spring wheat as well as endosperm in the mix. The
kernel. Bread flour is usually en- presence of bran reduces the gluten
riched and although similar to all- percentage in the flour mix therefore
purpose flour, it has greater gluten whole wheat breads are often heavier
strength and is generally used for yeast breads. than breads made from white flour.
Self-rising flour is an all-purpose flour with salt and Whole wheat flour is rich in B-vitamins, vitamin E and
leavening added. One cup of self-rising flour contains protein and contains more trace minerals and dietary
1 1/2 teaspoons baking powder and 1/2 teaspoon salt. fiber than white flour. Since whole wheat flour contains
so many minerals, it does not have to be enriched as
Cake flour is milled from soft wheat and is especially white flour does.
suitable for cakes, cookies, crackers, and pastries. It is
low in protein and low in gluten. In most recipes, whole wheat flour can be mixed half
and half with white flour to increase the gluten percent-
Pastry flour has comparable protein, but less starch age.
than cake flour. It is milled from a soft, low gluten
wheat and is used for pastries. Graham flour is another term for whole wheat
flour.
21
MILLING
Milling is the process used to grind wheat into flour. Flour is a value-added product derived from wheat, although
rarely thought as a value added product today, because we seldom buy whole wheat to grind at home ourselves.
The earliest methods of milling wheat was to find a large, sloping stone called a saddle stone and another smaller
stone to hold in ones hand. The wheat berries were then ground between these two stones to create a rough form
of whole wheat flour. A similar method of using a mortar and pestle was used at this time to grind wheat as well.
These processes were very laborious and time consuming, and since the berries were very coarsely ground, they
often wore down peoples teeth very rapidly.
Methods of milling continued to evolve until the invention of the millstone which consisted of two large horizon-
tal, disk-shaped stones, placed one on top of the other. The top stone turned while the bottom stone remained sta-
tionary while grain was fed in between. The millstone was powered by men, horses, oxen, and finally water or
wind. Romans were believed to be the first to use water power for milling flour in about 100 B.C. in Asia Minor.
Windmills were developed nearly a thousand years after water mills. Their use was first recorded in Normandy
and Provence, France in 1180 A.D.; Suffolk, England, in 1185 A.D.; and in Syria in 1190 A.D.
The automated mill made its first debut around 1785 by Oliver Evans. The mill included screw conveyors that
moved flour and wheat horizontally and bucket elevators that lifted the grain and its milled products, called grist.
Other new machines cleaned the wheat for a purer flour. By 1808 Evans granted a license to use his mill improve-
ments to Thomas Jefferson.
By 1870, mills required fewer than three employees. Water powered two-thirds of all mills and steam powered the
rest. In the middle of the 19th century with the development of harder wheat required the use of a new milling
process.
In the process, the miller sets the stones wider apart to crack, rather
than crush the wheat. The speed of the turning millstones was
slowed at the same time. This reduced the heat of friction and
ground and separated the wheat into bran and white flour by grad-
ual reduction and repeated grinding and bolting. The flour proc-
essed was similar to modern extraction rates of 72-75 percent flour
and 25-28 percent millfeed from a given weight of wheat.
Three key changes in milling moved it into the modern age by the
later half of the 19th century.
1) The invention of the steam engine by James Watt
(1769), and its application to American milling in the
1870s.
22
The use of rollers was a cost saver because dressing (regrooving and repairing) millstones is expensive. Steel roll-
ers also have to be regrooved and repaired, but it is a far different process than the work that was regularly needed
on the stones.
Rollers permitted a longer, more gradual extraction without the heat produced by millstones. This resulted in a
larger amount of better grade flour from a given amount of wheat. The bran was more cleanly separated from the
endosperm (the flour portion of the wheat) and produced a cleaner, more uniform flour. Rollers were also superior
for milling harder bread wheats.
The middling purifier added to this premium flour by blowing out the bran particles from the middlings, or coarse
farina particles released from the wheat endosperm by the roller mill action. The farina could then be further re-
duced, or ground and sifted repeatedly, to extract high grade, or patent flour.
Flour extraction is important to the miller. The largest profit is in the sale of flour, not millfeed, a term used to
classify all parts of the wheat that are not flour. Because an average bushel of wheat weighs about 60 pounds, the
miller hopes to extract about 45 pounds of flour (75 percent) and 15 pounds of millfeed (25 percent).
Milling efficiency has increased even further with improved equipment, expanded transportation and computeriza-
tion. It takes far fewer mills today to provide the flour and grain products that food processors, feed manufacturers
and other industries need.
Due to the fact that weather cannot be controlled nor wheat exactly matched to an end use, the miller still takes
what the farmer produces. However, todays miller fully knows the kind of wheat being milled, tests its properties,
and, by scientific blending, produces a huge variety of very specific flour and grain products.
23
MILLING TODAY
A closer look inside the mill shows us how flour is made and the great care and science used to make this basic
ingredient for so many favorite foods. Every mill is just a little different, depending on the kind of flour needed for
the end product. However, most mills follow many of the steps in roughly the same order.
PRODUCT CONTROL
Wheat arrives at the mill by truck, ship, barge, or rail car. Before the wheat is even unloaded, samples are taken to
ensure it passes inspection. X-rays may be used to detect any signs of insect infestation. Meanwhile, product con-
trol chemists begin their tests to classify the grain by milling and baking a small amount to determine the end-use
qualities. Wheat and flour tests are described in depth in the next section.
The results from these tests determine how the wheat will be handled and stored. Millers may blend different
wheats to achieve the desired end product. The wheat will then be stored at the mill in large bins. Storing wheat is
an exact science. The right moisture, heat and air must be maintained or the wheat may mildew, sprout, or fer-
ment.
MAGNETIC SEPARATOR
The wheat first passes by a magnet that removes iron and steel particles.
SEPARATOR
Vibrating screens remove bits of wood and straw and almost anything too big and too small to be wheat.
ASPIRATOR
Air currents act as a kind of vacuum to remove dust and lighter impurities.
DE-STONER
Using gravity, the machine separates the heavy material from the light to remove stones that may be the same size
as the wheat kernels.
DISC SEPARATOR
The wheat passes through a separator that identifies the size of the kernels even more closely. It rejects anything
longer, shorter, more round, more angular or in any way a different shape.
SCOURER
The scourer removes outer husks, crease dirt (dirt contained in the crease of the wheat berry) and any smaller im-
purities with an intense scouring action. Currents of air pull all the loosened material away.
Tempered wheat is stored in bins from 8 to 24 hours, depending on the type of wheat - soft, medium or hard.
Blending of wheats may be done at this time to achieve the best flour for a specific end use.
24
IMPACT SCOURER
Centrifugal force breaks apart any unsound kernels and rejects them from the mill flow.
From the entoleter, the wheat flows to grinding bins, large hoppers that will measure or feed wheat to the actual
milling process.
This modern milling process is a gradual reduction of the wheat kernels. The goal is to produce middlings, or
coarse particles of endosperm. The middlings are then graded and separated from the bran by sieves and purifiers.
Each size returns to corresponding rollers and the same process is repeated until the desired flour is obtained. The
rolls are paired and rotate inward against each other, moving at different speeds. Just one pass through the
corrugated first break rolls begins the separation of bran, endosperm and germ.
From the rolls, the grist (ground wheat) is sent way upstairs to drop through sifters. The grist is moved via pneu-
matic systems that mix air with the particles so they flow, almost like water, through tubes. This is a great advance
in health and safety from earlier methods of moving the grist with buckets.
SIFTERS
The broken particles of wheat are introduced into huge, rotating, box-like sifters where they are shaken through a
series of bolting cloths or screens to separate the larger from the smaller particles. Inside the sifter, there may be as
many as 27 frames, each covered with either a nylon or stainless steel screen, with square openings that get smaller
and smaller the farther down they go.
Up to six different sizes of particles may come from a single sifter, including some flour with each sifting. Larger
particles are shaken off from the top, or scalped, leaving the finer flour to sift to the bottom. The scalped fractions
are sent to other roll passages and particles of endosperm are graded by size and carried to separate purifiers.
PURIFIERS
In a purifier, a controlled flow of air lifts off bran particles while at the same time a bolting cloth separates and
grades coarser fractions by size and quality.
Four or five additional break rolls, each with successively finer corrugations and each followed by a sifter, are usu-
ally used to rework the coarse stocks from the sifters and reduce the wheat particles to granular middlings that are
as free from bran as possible. Germ particles will be flattened by later passage through the smooth reduction rolls
and can be easily separated. The reduction rolls reduce the purified, granular middlings, or farina, to flour.
The process is repeated over and over again, sifters to purifiers to reducing rolls, until the maximum amount of
flour is separated, consisting of close to 75 percent of the wheat. The remaining percentage of the wheat kernel or
berry is classified as millfeedshorts, bran and germ.
25
Bakers buy a wide variety of flour types, based on the products they produce. The flour the consumer buys at the
grocery store, called family flour by the milling industry, is usually a long-patent all-purpose or bread flour. Oc-
casionally short patent flour is available in retail stores.
Reconstituting, or blending back together, all parts of the wheat in the proper proportions yields whole wheat
flour. This process produces a higher quality whole wheat flour than is achieved by grinding the whole wheat
berry. Reconstitution assures that the wheat germ oil is not spread throughout the flour so it does not go rancid so
readily.
BLEACHING FLOUR
Toward the end of the line in the millstream, if the flour is to be bleached, the finished flour flows through a device
which releases a bleaching-maturing agent in measured amounts.
It has been known for centuries that freshly milled flour makes a lesser quality baked product. In the old days,
flour was stored for a few months to mature, or naturally oxidize. This whitened the flour and improved its baking
characteristics. The modern bleaching process simply duplicates this natural oxidation process, but does so more
quickly.
In the bleaching process, flour is exposed to chlorine gas or benzoyl peroxide to whiten and brighten flour color.
Chlorine also affects baking quality by maturing or oxidizing the flour, which is beneficial for cake and cookie
baking. The bleaching agents react and do not leave harmful residues or destroy nutrients.
ENRICHMENT
What is an important source of iron in the diet, especially for those who eat few eggs or little red meat? Why is
beriberi no longer a public health concern?
The enrichment of flour with three B vitamins (thiamin, niacin and riboflavin) and iron, begun in the 1930s, is the
answer to both questions.
The flour stream passes through a device that measures out specified quantities of enrichment. If the flour is self-
rising, a leavening agent, salt and calcium are also added in exact amounts.
Before the flour leaves the mill, additional lab tests are run to ensure that the customers get what they ordered.
Finally, the flour millstream flows through pneumatic tubes to the packing room or into hoppers for bulk storage.
Family flour for retail sale may be packed in 5, 10, or 25 pound bags. Bakery flour may be packed in 50-100
pound bags or sent directly to bulk trucks or rail cars.
26
27
28
29
30
31
Moisture Content
Low temperature heating
Measures moisture content
Method
1. 2-3 grams of flour is weighed and placed in a moisture dish.
2. Sample is heated to 266F in an air oven for one hour.
3. Sample is cooled to room temperature and the residue is weighed.
Results
Moisture content is determined by comparing the weight of the sample before and after heating.
The amount of weight loss is the moisture content.
This amount is expressed as a percentage. An example of a common HRW wheat moisture is 11.4%.
Wheat or flour with a high moisture content (over 14.5%) attracts mold, bacteria, and insects, all of which cause
deterioration during storage.
32
Protein Content
High Temperature combustion
Measures protein content
Method
1) A sample of flour or ground wheat (0.15-0.20 grams) is weighed and placed into a CAN protein analyzer.
2) This process is fully automated and begins by dropping the sample into a hot oven where it is burned at
1,746F.
1) The amount of nitrogen gas released during burning is measured and a formula is applied to convert this meas-
urement to protein content in the sample.
Results
Since protein is the major wheat compound that contains nitrogen, the protein content can be determined by meas-
uring the amount of nitrogen released during burning.
Protein content results are expressed as a percentage of the total sample weight; for example, 10% protein content
on 12% moisture basis for wheat or 8.5% on 14% moisture basis for flour.
Method
1) A sample of flour or ground wheat (3-5) grams is weighed and placed in an ash cup.
2) The sample is heated to 1,085F in an ash oven until its weight is stable. (Usually overnight).
3) The residue is cooled to room temperature and then weighed.
Results
The high temperature of the oven drives out the moisture and burns away all organic materials (starch, protein,
and oil), leaving only the ash. The residue (ash) is composed of the non-combustible, inorganic minerals that are
concentrated in the bran layer.
Ash content results for wheat or flour ash are expressed as a percentage of the initial sample weight; for exam-
ple, wheat ash of 1.58% or flour ash of 0.52%. Wheat or flour ash is usually expressed on a common moisture
basis of 14%.
34
Flour Color Analysis
Color analysis
Measures flour color
One method to measure flour color is the Minolta Chroma Meter Test.
Method
1) A sample of flour is placed on the granular materials attachment and compacted.
2) The Minolta Chroma Meter is inserted into the granular materials attachment.
3) Measurements are taken and recorded.
Results
Flour color is determined by measuring the whiteness of a flour sample with the Minolta Chroma Meter.
The rating scale is as follows