WIS5 NoneDestructiveTesting

Welding Inspection
Non-Destructive Testing
Course Reference WIS 5
Non-Destructive Testing
A welding inspector should have a working knowledge
of NDT methods and their applications, advantages and
disadvantages.
Four basic NDT methods
Magnetic particle inspection (MT)
Dye penetrant inspection (PT)
Radiographic inspection (RT)
Ultrasonic inspection (UT)

WI 3.1
Dye Penetrant Inspection
Copyright 2003 TWI Ltd M.S.Rogers

Surface breaking defects only detected
This test method uses the forces of capillary action to
detect surface breaking defects
The only limitation on the material type is the material can
not be porous
Penetrants are available in many different types
Water washable contrast
Solvent removable contrast
Water washable fluorescent
Solvent removable fluorescent
Post-emulsifiable fluorescent
Step 1. Pre-Cleaning
Ensure surface is very Clean normally with the use of a
solvent
Step 2. Apply penetrant
After the application of the penetrant the penetrant is normally
left on the components surface for approximately 15 minutes
(dwell time). The penetrant enters any defects that may be
present by capillary action
Step 3. Clean off penetrant
After sufficient penetration time (dwell time) has be given the
penetrant is removed, care must be taken not to wash any
penetrant out off any defects present
Step 3. Apply developer
After the penetrant has be cleaned sufficiently a thin even
layer of developer is applied. The developer acts as a
contrast against the penetrant and allows for reverse capillary
action to take place
Step 4. Inspection / development time
Inspection should take place immediately after the developer
has been applied any defects present will show as a bleed
out during development time. After full inspection has been
carried out post cleaning is generally required.
Fluorescent Penetrant Bleed out viewed
under a UV-A light
source
Bleed out viewed

under white light
Colour contrast Penetrant
Advantages Disadvantages
Simple to use Surface breaking defect
Inexpensive only
Quick results little indication of depths
Can be used on any Penetrant may
non-porous material contaminate component
Portability Surface preparation
Low operator skill critical
required Post cleaning required
Potentially hazardous
chemicals
Magnetic Particle WI 3.1
Inspection

Magnetic Particle Inspection
Surface and slight sub-surface detection
Relies on magnetization of component being tested
Ferro-magnetic materials only can be tested
A magnetic field is introduced into a specimen being tested
Methods of applying a magnetic field, yoke, permanent
magnet, prods and flexible cables.
Fine particles of iron powder are applied to the test area
Any defect which interrupts the magnetic field, will create a
leakage field, which attracts the particles
Any defect will show up as either a dark indication or in the
case of fluorescent particles under UV-A light a green/yellow
indication
Collection of ink
particles due to leakage
field
Electro-magnet (yoke) DC or AC
Prods DC or AC
A crack like
indication
Alternatively to contrast
inks, fluorescent inks
may be used for greater
sensitivity. These inks
require a UV-A light
source and a darkened
viewing area to inspect
the component
Typical sequence of operations to inspect a weld
Clean area to be tested

Apply contrast paint
Apply magnetisism to the component
Apply ferro-magnetic ink to the component
during magnatising
Iterpret the test area
Post clean and de-magnatise if required
Simple to use Surface or slight sub-

Inexpensive surface detection only
Magnetic materials only
Rapid results
No indication of defects
Little surface
depths
preparation required
Only suitable for linear
Possible to inspect
defects
through thin coatings
Detection is required in
two directions
WI 3.1
Ultrasonic Inspection
Copyright 2003 TWI Ltd Section Ref 15 M.S.Rogers

Surface and sub-surface detection
This detection method uses high frequency sound waves,
typically above 2MHz to pass through a material
A probe is used which contains a piezo electric crystal to
transmit and receive ultrasonic pulses and display the
signals on a cathode ray tube or digital display
The actual display relates to the time taken for the
ultrasonic pulses to travel the distance to the interface and
back
An interface could be the back of a plate material or a
defect
For ultrasound to enter a material a couplant must be
introduced between the probe and specimen
Pulse echo UT Set, Digital
signals
A scan Display
Compression probe Thickness checking the material

defect Back wall

initial pulse echo echo
Material Thk
defect
0 10 20 30 40 50
Compression Probe CRT Display

UT Set
A Scan
Display
Angle Probe
initial pulse
defect echo
defect 0 10 20 30 40 50
Skip CRT Display
initial pulse
defect echo
defect 0 10 20 30 40 50
Full Skip CRT Display

Rapid results Trained and skilled
Both surface and sub- operator required
Requires high operator
surface detection
skill
Safe
Good surface finish
Capable of measuring the required
depth of defects Defect identification
May be battery powered Couplant may
Portable contaminate
No permanent record
Any Questions

WI 3.1
Radiographic Inspection

The principles of radiography
X or Gamma radiation is imposed upon a test object
Radiation is transmitted to varying degrees dependant
upon the density of the material through which it is
travelling
Thinner areas and materials of a less density show as
darker areas on the radiograph
Thicker areas and materials of a greater density show
as lighter areas on a radiograph
Applicable to metals,non-metals and composites
X - Rays Gamma Rays

Electrically generated Generated by the
decay of unstable
atoms
Source
Radiation beam Image quality indicator
10fe16
Radiographic film Test specimen

Source
Radiation beam Image quality indicator
10fe16
10fe16
Test specimen
Radiographic film with latent image after exposure

Radiographic Quality
Density - relates to the degree

of darkness
Contrast - relates to the degree of difference
Definition - relates to the degree of sharpness
Sensitivity - relates to the overall quality of the

radiograph
Radiographic Sensitivity
7FE12
Step / Hole type IQI Wire type IQI

Image Quality Indicators
Step/Hole Type IQI
Wire Type IQI

Radiographic Techniques
Single Wall Single Image (SWSI)

- film inside, source outside
Single Wall Single Image (SWSI) panoramic
- film outside, source inside (internal exposure)
Double Wall Single Image (DWSI)
- film outside, source outside (external exposure)
Double Wall Double Image (DWDI)
- film outside, source outside (elliptical exposure)
Single wall single image SWSI
Film
Film
IQIs should be placed source side

Single wall single image SWSI panoramic
Film
IQIs are placed on the film side

Source inside film outside (single exposure)
Double wall single image DWSI
Film
IQIs are placed on the film side

Source outside film outside (multiple exposure)
This technique is intended for pipe diameters
over 100mm
Double wall single image DWSI
Identification
Unique identification
EN W10
IQI placing
Pitch marks A B
indicating readable ID
film length MR11
Radiograph
Double wall double image DWDI
Film
IQIs are placed on the source or film side
Source outside film outside (multiple exposure)
A minimum of two exposures
This technique is intended for pipe diameters
less than 100mm
Identification 4 3
Unique identification EN W10
IQI placing
Pitch marks 1 2
indicating readable ID
film length MR12
Shot A Radiograph
Elliptical
exposure
Permanent record Expensive consumables
Bulky equipment
Little surface preparation
Harmful radiation
Defect identification Defect require significant
No material type limitation depth in relation to the
Not so reliant upon radiation beam
Slow results
operator skill
Very little indication of
Thin materials depths
Access to both sides
required
Any Questions
Copyright 2003 TWI Ltd Section Ref 15 M.S.Rogers

Questions
QU 1. Name four NDT methods
QU 2. State the two radiation types used in industrial radiography

and state advantages of each.
QU 3. Give the advantages and disadvantages of radiography

and conventional ultrasonic inspection.
QU 4. Give the main disadvantages of magnetic particle

inspection and give at least three methods to magnetise a
component.
QU 5 State the main limitations of dye penetrant inspection.

WIS5 NoneDestructiveTesting

Uploaded by

Copyright:

Available Formats

WIS5 NoneDestructiveTesting

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

WIS5 NoneDestructiveTesting

Uploaded by

Copyright:

Available Formats

Welding Inspection

Four basic NDT methods

Magnetic particle inspection (MT)

Dye penetrant inspection (PT)

Radiographic inspection (RT)

Ultrasonic inspection (UT)

Dye Penetrant Inspection

Copyright 2003 TWI Ltd M.S.Rogers

Bleed out viewed

Copyright 2003 TWI Ltd M.S.Rogers

Clean area to be tested

Simple to use Surface or slight sub-

Copyright 2003 TWI Ltd Section Ref 15 M.S.Rogers

Compression probe Thickness checking the material

defect Back wall

Compression Probe CRT Display

Skip CRT Display

Full Skip CRT Display

Copyright 2003 TWI Ltd M.S.Rogers

Copyright 2003 TWI Ltd M.S.Rogers

X - Rays Gamma Rays

Radiation beam Image quality indicator

Radiographic film Test specimen

Radiation beam Image quality indicator

Radiographic film with latent image after exposure

Density - relates to the degree

Contrast - relates to the degree of difference

Definition - relates to the degree of sharpness

Sensitivity - relates to the overall quality of the

Step / Hole type IQI Wire type IQI

Step/Hole Type IQI

Wire Type IQI

Single Wall Single Image (SWSI)

IQIs should be placed source side

IQIs are placed on the film side

IQIs are placed on the film side

Copyright 2003 TWI Ltd Section Ref 15 M.S.Rogers

QU 2. State the two radiation types used in industrial radiography

QU 3. Give the advantages and disadvantages of radiography

QU 4. Give the main disadvantages of magnetic particle

QU 5 State the main limitations of dye penetrant inspection.

You might also like