Scribd
Upload
327 views4 pages

Wps

This welding procedure specification outlines the parameters for single V-groove welds on 170mm diameter, 10mm thick SA 53 B steel pipe using SMAW. Four passes will be used with E7018 3.2mm electrodes for passes 2-4 and E7016 2.6mm for the root pass. Welding will proceed downhill from the root to the fill passes at a travel speed of 40-100mm per minute. The welds will be made in the 1G position by two welders and tested through guided bend, tensile, and nick-break tests.

Uploaded by

MahfudRido'iRonggomania
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
327 views4 pages

Wps

This welding procedure specification outlines the parameters for single V-groove welds on 170mm diameter, 10mm thick SA 53 B steel pipe using SMAW. Four passes will be used with E7018 3.2mm electrodes for passes 2-4 and E7016 2.6mm for the root pass. Welding will proceed downhill from the root to the fill passes at a travel speed of 40-100mm per minute. The welds will be made in the 1G position by two welders and tested through guided bend, tensile, and nick-break tests.

Uploaded by

MahfudRido'iRonggomania
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

WELDING PROCEDURE SPESIFICATION NUMBER 1

Process : SMAW
Matrial : SA 53 B
Pipe outside diameter and wall thickness : 170 mm 10 mm
Joint design : V Grove
Filler metal and number of bead : A 5.5 Group 3 , 4
Electrical or flame characteristic : DC EP
Position : 1G
Direct of welding : downhill to uphill
Number of welder :2
Time lapse between passes : N/A
Type and removal of lineup clamp : N/A
Cleaning and/or grinding : Cleaning and grinding
Preheat/PWHT : N/A
Shielding gas and flow rate : N/A
: low hydrogen potasium and iron pwoder
Speed of travel : 40 100 mm/ menit

Tested : Kelompok 4
Welder : Syarifal wildan and mahfud ridoi
Approved : PPNS

Welding supervisor : Fany listya nurani


Adopted : Riano arsanta
Chief engineer : Miftaqus syifa

Joint Design

ELECTRODE SIZE AND NUMBER OF BEAD


Bead number Electrode size and voltage Amper and Speed
type polarity (mm/menit)
1 E 7016 2.6 mm 19-23 71-73 DCEP 72.8
2 E 7018 3.2 mm 23-25 95-96 DCEP 99.38
3 E 7018 3.2 mm 24-26 95-96 DCEP 47.5
4 E 7018 3.2 mm 23-25 95-96 DCEP 72.24

Aproved By

Mahfud RidoI
Welding Engineer
WELDING SPECIFICATION PROCEDURE

TEST PARAMETERS
Joint Type: Full Pene. Butt Diameter: 170 mm

Thickness: .10 mm Filler: 3.2 E 7018 2.6 E 7016

Material: ASTM SA 53 Gr B Preheat: N/A IPT N/A

Position: Roll welding (1G) Current: DCEP Amps: 71-99

Progression: E-7018 V/Dn E-7016 V/Dn. root Volts: 19-23

GUIDED BEND TESTS


No. Type Result No. Type Result
1. Face 1 Acc. 5.
2. Root 1 Acc. 6.
3. Face 2 Acc. 7.
4. Root 2 Reject 8.

TENSILE TESTS
No. Specimen Area Applied Ultimate Character of failure and location
Type (mm2) Load (KN) Tensile
1. TS 1 284.59 133.59 469.42 BM
2. TS 2 284.35 126.97 446.52 BM

NICK-BREAK TESTS
No. Type Remarks on Nick-Break tests

1. N1 No defect
2. N2 No defect
Welders Name: Syarifal wildan & mahfud Ridoi Z No.: 1 Stamp:

Procedure developed and conducted by: By: Kelompok 4 Date:_21/07/2016

Autorized by Kelompok 4
4

You might also like