Antenna Matching Techniques
Antenna Matching Techniques
Antenna Matching Techniques
As with antenna types, there are numerous matching techniques employed in amateur radio antennae.
Many of these techniques depend on the frequency of use and the antenna type. We will take a quick
look at several popular types here. For a more in-depth examination of matching networks, consult the
ARRL Antenna Book.
The Matchbox
Perhaps the most popular of matching networks is the matchbox, or tuner as it has come to be known.
Previously, we discussed that the tuner is not an antenna matching device but a coax to rig matching
device. If this concept is still not clear you should review the discussion we presented earlier until your
concept of the matchbox is solidly based on the principles presented here.
One of the simplest of matches for dipoles is the series lumped component match. This is a complicated
way of saying we can put a coil or capacitor in series or parallel with the antenna to bring the
impedance presented the feedline, closer to the characteristic impedance of the coax (thus lowering the
SWR at the antenna). This form of matching is more often seen in VHF than HF type antennas, but
historically is well represented in VHF dipole configurations.
An example of the lumped impedance transmission line matching is shown in the illustration. If we
recall the study of resonate circuits we will be able to apply that knowledge to surmise that antenna
matching with very low impedances (like mobile verticals) may need series matching. And in fact
almost all marine and CB fiberglass whip antennas do contain some form of series matching to bring
the very low (typically 3-10 ohms) impedance up to the nominal coax impedance of 50 or 75 ohms.
Dipoles very often are much higher in impedance than coax or twin lead impedances. This situation
may use parallel matching to lower impedances presented to the feedline. In the illustration, a short
(less than wavelength) coax stub is used to compensate for antenna impedances that are capacitive or
inductive in value. The shorted stub as shown is inductive in value, while an open stub of similar length
would be capacitive. It is even possible, (and likely in most fiberglass verticals) that the antenna
element has a short length of higher impedance cable in series with the radiating element. A classic
example of this type of matching is the wavelength matching stub. The stub match is a length of
transmission line that is one-quarter wavelength at the center operating frequency. Millions of antennas
like this have been sold for the Citizen's Band, Marine band, and 2 meter ham band under very famous
brand names. Many times (not always, but quite often) transmission line stub matching is an indication
of non-resonate wide-SWR bandwidth antenna design parameters for a single narrow band of
frequencies (like the 155.5 157.0 MHz marine VHF band or 144-148 MHz 2 meter amateur band).
The transmission line type matching is much harder to recognize and describe.
It does, however, illustrate how variations on mechanical means can accomplish a broad range of
challenging matching conditions. This beam accomplishes 4.9 db of gain with 15 db f:b in only a
sixteen foot boom on 40 meters. The 3:1 SWR bandwidth is 150 kHz. Quite good for a very compact
40 meter beam.
The same kind of loading/matching can be seen in the linear loaded dipole seen in QST July 2002
issue. The author, Lew Gordon K4VX, has used the same loading/matching principals to make a
shortened wide-band dipole for 40 meters. The stated 2:1 SWR bandwidth is 300 kHz from the design
center frequency. The article provides SWR graphics to show the performance of this unique antenna.
Although the physical appearance is different, the principals are the same between the two antennas of
vastly differing construction methods.
The Real Scoop On SWR
In this treatise we have looked at SWR and discovered many things that are true, and dispelled a few
myths perpetuated in ham radio circles. So what does all this come down to?
If there is anything you need to carry away from a thorough reading of the material, it is that:
1) There are a number of factors, simple and complex that affect SWR.
2) Not all antennas are 50 ohms. They come in all manner of impedances.
3) SWR alone is not a sole consideration for antenna effectiveness. We must also consider
radiation efficiency and radiated pattern in the entire system.
4) Low SWR does not mean your antenna is radiating properly. Nor does a modest SWR mean
your antenna will not work or that you cannot use some antenna types at your installation.
5) An antenna that Works may mean something different to you than to another ham. Generally
we give this term the meaning that it is relatively easy to tune to a workable SWR in our band
segment and we get good signal reports from the important distant stations contacted. Very Low
SWR should not be the only meaning given to how an antenna works. You may notice that
some antennas that exhibit very low SWR are not necessarily the best performers in your
application.
6) You CAN operate your rig on an antenna system that exhibits a significant SWR WITHOUT
DAMAGE due to SWR. Notwithstanding that some rigs and power amps have a SWR lockout
set at about 3:1, with a good tuner you can operate with high SWR under some circumstances
without equipment damage and with surprising results.
7) Your tuner does not tune your antenna. It provides an additive phase-linear match to the
transmission line by redirecting the reflected power measured (due to impedance mismatch at
the antenna). At the same time a nominal impedance is presented to your transmitter so it will
operate efficiently enough so as not to damage components due to the increased heat generated
from working harder than it should to generate operable RF power.
8) Antennas are complex and are affected by everything around them, especially the ground and
resonating conductors near them. This can be a good thing (as in Yagi antennas) or a bad thing
(as in ground-loop resonating).
9) Don't trust advertising hype from manufacturers. Look at stated specs with an educated eye. No
one can operate beyond the laws of physics and wave dynamics. If you are skeptical, consult an
Elmer before spending your hard earned cash on unrealistic promises. Use the knowledge you
have gained from these pages and make better, more informed choices.
You are highly encouraged to use the information sources provided at the end. There is much more to
antenna theory and practice than could be covered here. These sources provide a wealth of information
that you can use every day.