International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395 -0056

Volume: 04 Issue: 03 | Mar -2017 www.irjet.net p-ISSN: 2395-0072

PIC Microcontroller based baby incubator using sensors

Dhruvkumar Pandya1, Jay Parmar2, Apurva Patel3
1 Student IV Year B.E, Dept. of EE, Vadodara Institute of Engineering, Kotambi, Gujarat, India.
2 Student IV Year B.E, Dept. of EE, Vadodara Institute of Engineering, Kotambi, Gujarat, India.
3 Student IV Year B.E, Dept. of EE, Vadodara Institute of Engineering, Kotambi, Gujarat, India.

---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - There are 16 million babies are born too early In incubator microprocessor is use for the controller
every year. The rate of preterm birth range from 6%-20% of temperature, humidity and gas concentration. Fan is
babies born across 184 countries according to WHO. Almost provided to circulate air and distribute heat in incubator. In
4 million children die each year due to preterm birth. In the incubator manual set temperature and humidity used.
first month, one million die on the first day low birth weight Temperature, humidity and gas level displays, high and low
(LBW) is the greatest risk of the new born babies. The temperature and gas indicators and low water indicator.
countries with the greatest numbers of preterm births are in Figure 1 Incubator Heating System
India-35,19,100; China- 11,72,300,Pakistan- 7,48,100,U.S-
5,17,400 and Brazil-2,79,300.The microcontroller based
baby incubator help to all peoples. Cost of this project is very
low. So, everyone which belongs to economical backward
also use this. Today baby incubator used in all big hospital.
This project not only used for monitoring and controlling
the temperature but also provide of advantages such as
controlling humidity and monitoring the heart beat and
respiration.

Key Words: Microcontroller, Temperature sensor,

Humidity sensor, Heart beat sensor, Respiration
sensor, GSM modems, Baby incubator, switching
circuit, etc.

1. INTRODUCTION The basic operation of the circuit is monitoring the

temperature and humidity within the incubator shell. The
temperature sensor will detect the temperature and send
This project is design to control the temperature and
the single to the microprocessor for further action. If the
humidity. It is use to control the temperature and
temperature level is high, then the microprocessor will
humidity of a small environment in a baby incubator. A
send single to the temperature injector to open the valve.
baby incubator system is use for the Preterm birth babies,
Some time microprocessor send single to outlet the air flow
new born babies and sick babies. It provides a safe and
in incubator. In incubator the temperature level too low,
clean environment, with fresh air, clean and sterile
the microprocessor send the single to the fan, and fan will
ambient condition for the babies. In baby incubator
be stopped. High and low temperatures level detection, the
provide a homogeneous and stable temperature, a relative
red color light blink and the warning by the alarm system.
humidity level, heart beat and repatriation sense and
concentration that is need especially for intensive care of
the preterm baby and full term baby. Most of the baby
incubators are made up of using microprocessors.

1.1 Incubator Heating System

For this an automatic incubator comprises a chamber
surrounded by a water jacket and insulation with
temperature and gas level sensors, a gas injection and
separate water jacket and air heaters.

2017, IRJET | Impact Factor value: 5.181 | ISO 9001:2008 Certified Journal | Page 1906
 International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395 -0056
Volume: 04 Issue: 03 | Mar -2017 www.irjet.net p-ISSN: 2395-0072

Figure 2 Control circuit for incubator using

Microprocessor

2. Block Diagram and Description

Microcontroller: It will Read all information from sensors Figure 3 Block Diagram
and compare it with Set Levels. If any problem it will send
SMS to Operator and Buzzer will Sound. It Regularly Log Computer: It is used for Logging Data with time and
Data in Computer for Monitoring of Patient. Sensor information in Real Time.
GSM Modem (SIM300): this is used for sending SMS to
LCD: it is used for Display Sensor information and System operator about emergency in incubator.
Running Status.
Relay Driver: Relay cant be connecting directly to MCU to
Buttons: These are used for change the Set Level of save MCU from Short Circuit and High Current. So to
Sensing Information. provide isolation we need Relay Driver. We have used
ULN2003. It consists of 7 Relay Driver modules inside a
Temp. & Humidity Sensor: we have selected combine single chip.
Module Named DHT22. It is Purely Digital. It communicates
with MCU by one wire. It directly gives digit data so we Buzzer: it is used for generate sound at the time of
dont have to convert the data, we just have to get it and emergency.
print it. Relays: these are used for switching the Lights by electrical
signal from MCU.
Heart Beat Sensor: In our top of our finger Blood
Circulation is changed as per our Heart Beats. So it changes 3. RELATED WORK
it Density accordingly Heart Beat and it sense by the IR
Light. I. Temperature Sensor & Humidity Sensor

Respiration Sensor: As we Breath our Chest is Changes its

state. If we attach Flex Sensor then we can get digital
output from it. So we will use Flex Sensor.

Switching Circuit: We need Connection of Computer and

GSM Modem. Both need UART Module to Communicate
with MCU. Our MCU have only one UART Module. So we
have connected Switching Circuit by which we can connect
both simultaneously when it need.

Respiration Sensor: As we Breath our Chest is Changes its

state. If we attach Flex Sensor then we can get digital Fig 4: Temperature Sensor & Humidity Sensor
output from it. So we will use Flex Sensor.
The DHT22 is a basic, low-cost digital temperature and
humidity sensor. In DHT22 Polymer capacitor Sensing
element is used. It is simple to use. Temperature range is -
Switching Circuit: We need Connection of Computer and
400 to 900 Celsius and humidity range is 0 to 100%RH.it is
GSM Modem. Both need UART Module to Communicate
sensing period is 2 second. The second pin is data pin it is
with MCU. Our MCU have only one UART Module. So we
connect to the microcontroller. Third is NC (Not connected)
have connected Switching Circuit by which we can connect
both simultaneously when it need.

2017, IRJET | Impact Factor value: 5.181 | ISO 9001:2008 Certified Journal | Page 1907
 International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395 -0056
Volume: 04 Issue: 03 | Mar -2017 www.irjet.net p-ISSN: 2395-0072

pin and fourth pin is show in fig this pin is ground pin.
DHT22 sensor is give data after every 3 second.
This sensor is more precise, more accurate and works in a
bigger range of temperature/humidity.
Its larger and more expensive.Temperature sensor
connected to the microcontroller. In baby incubator DHT22
detect temperature more then 34. Celsius, so cooling fan
will be switched on automatically and bulb is switch off. In
case temperature is decrease to the 340 Celsius so bulb is
automatically switch on. Temperature sensor maintains
the 340 to 35.50 Celsius temperature in baby incubator. Fig 5: circuit diagram of Heart beat sensor
DHT 22 also maintain temperature and humidity in
incubator. III. Respiration sensor

Below table shows relation between weight and range of Respiration sensor is developes by us. In this sensor flex
temperature. sensor is use. Flex sensor work based on resistive carbon
element. Flex sensor is variable printed resister. Flex
Sensors use for the P5 gaming glove, and the below
applications:

Automotive controls, Medical devices, Industrial controls,

Computer peripherals, Fitness products, Musical
instruments.

In flex sensor normal condition the normal resistance

value but it is band 45o increased resistance value. Further
band 90o more increased resistance value.

Table 1
II. Heart beat sensor
Heartbeat sensor is developed by us. In heartbeat sensor
two Operational amplifiers is use. In top of our finger
Blood Circulation is changed as per our Heart Beats. So it
changes its Density accordingly Heart Beat. If we apply IR
signal to our finger it reflect different IR light as its
density. But this change is Very small. So we have
connected 2 Non -inverting Amplifier with Gain of 101. So
we will get Pulses of Our Heart Beat.
Fig 6 Circuit Diagram of Respiration sensor

IV. GSM Modem (SIM 300)

The GSM modem can accept any GSM network and

operated by SIM card. Switching circuit is use to
communicate and develop embedded application.
Switching circuit developed by us. In switching circuit we
can use 7432 and 7408. It is developed by very easy. The
Table 2 modem is connected to directly pc serial port and PIC
microcontroller pin RX/TX. In case baby heartbeat pulse is
reduced the rated pulse in baby incubator it sends the
message to screen or mobile; If breathing rate is reduced
to the rated value so, GSM modem sends to the mobile and
screen.

2017, IRJET | Impact Factor value: 5.181 | ISO 9001:2008 Certified Journal | Page 1908
 International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395 -0056
Volume: 04 Issue: 03 | Mar -2017 www.irjet.net p-ISSN: 2395-0072

V. PIC Microcontroller Temperature sensor, Humidity sensor, Flex sensor, and

Heartbeat sensor is used. There are many functions are
The microcontrollers played revolutionary role in involved such as cooling, heating, pulse rating, display all
embedded industry and other place after the invention of readings, etc.
89c51. The steady and progressive research in this field
gave the hospital, industry and other place more efficient,
high-performance and low-power consumption
microcontrollers. The AVR, PIC and Ardiono are the prime
examples.

Full form of PIC Microcontroller Peripheral Interface

controller, it is one of the advanced microcontrollers
developed by microchip technologies. This
microcontroller is widely using in modern electronics
applications. This controller is more advanced than
normal microcontroller like 89c51.

Fig 8 Circuit Diagram

6. RESULTS

Fig 7

PIC controller is 8 bit microcontroller. In PIC16F877A is

40 pin microcontroller device. The PIC16F877A features
256 bytes of EEPROM data memory, 2 Comparators, 8
channels of 10 -bit Analog- to-Digital (A/D) converter, 2
capture/compare/PWM functions, the synchronous serial
port can be configured as either 3 -wire Serial Peripheral
Interface (SPI) or the 2-wire Inter-Integrated Circuit Fig 9 Result 1
(IC) bus and a Universal Asynchronous Receiver
Transmitter (USART), self-programming.

VI. Cooling Fan

Cooling fans come in all shapes and sizes as well as

voltages, airflow and case size. It is important to know the
specific type of fan your CPU or electronic component
requires as fans. In the baby incubator the temperature or
humidity is increases to the rated value the fan is on
condition otherwise fan is off condition. A relay circuit is
used for the switching the voltage from 5V to 12V, which is
the Voltage required to run the Fan.

5. CIRCUIT DIAGRAM Fig 10 Result 2

The given circuit diagram shows interfacing between all

components of this project. Here PIC Microcontroller is
use to control the all sensors in the baby incubator.

2017, IRJET | Impact Factor value: 5.181 | ISO 9001:2008 Certified Journal | Page 1909
 International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395 -0056
Volume: 04 Issue: 03 | Mar -2017 www.irjet.net p-ISSN: 2395-0072

heartbeat and respiration ratings are continuously display

on LCD.

REFERENCES

[1] Med A.Z.,Elyes F., and Abdelkader M., American

Journal of Engineering and Applied Sciences,
Application of Adaptive Predictive Control to a
Newborn Incubator, 4 (2): 235-243, ISSN 1941-7020,
2011.
[2] Microcontroller Based Baby Incubator Using Sensors,
M.Suruthi, S.Suma, International Journal of Innovative
Fig 11 Result 3 Research in Science, Engineering and Technology, Vol.
4, Issue 12, December 2015, ISSN 2319-8753.
[3] PIC Microcontroller based Efficient Baby Incubator,
International Journal of Advanced Research in
Electrical, Electronics and Instrumentation
Engineering, Vol. 4, Issue 2, February 2015, ISSN
(Online): 2278 8875.

BIOGRAPHIES
Dhruvkumar Pandya is
currently pursuing Bachelor of
engineering in electrical field
from Vadodara Institute of
Engineering, Kotambi,
Vadodara, Gujarat.

Jay Parmar is currently

pursuing Bachelor of
engineering in electrical field
from Vadodara Institute of
Fig 12
Engineering, Kotambi,
Vadodara, Gujarat.
7. CONCLUSIONS

The project is designed keeping in mind the medical Apurva Patel is currently
conditions available in rural areas. This Equipment can be pursuing Bachelor of
effectively used by technicians in a small health care engineering in electrical field
centre. It can be a life saving machine for premature baby from Vadodara Institute of
as well as low birth weight babies. The components can be Engineering, Kotambi,
easily fixed. The chamber is sufficient enough to Vadodara, Gujarat.
accommodate the baby comfortably. The temperature and
humidity of the system can be easily understood. This
project is simple and efficient in maintaining the
temperature and humidity of the in the incubator
irrespective of the outside temperature and humidity. It is
low cost design.
Above figure shows the Simulation results of complete
circuit carried out using Proteus software. The results
obtained from the PIC16F877A microcontroller interfaced
with one DHT22 temperature sensors and humidity
sensor. The LCD is used to monitor the sensor readings. If
the temperature in incubator increased above 370c then
cooling fan is on condition and heating bulb is off
condition, similarly if temperature decreases then heating
bulb is on condition and cooling fan is off condition. Also

2017, IRJET | Impact Factor value: 5.181 | ISO 9001:2008 Certified Journal | Page 1910