TTP-2410M Service Manual E

TTP-2410M/346M/644M
TTP-246M Plus/344M Plus
THERMAL TRANSFER / DIRECT THERMAL

BAR CODE PRINTER
SERVICE
MANUAL
TTP-2410M/346M/644M
Bar Code Printer Service Manual
TABLE OF CONTENT
1. FUNDAMENTAL OF THE SYSTEM .......................................................................... 1
1.1. Overview ................................................................................................................. 1
2. ELECTRONICS.......................................................................................................... 5
2.1 Summary of Board Connectors ............................................................................. 5
2.2 Interface Pin Configuration .................................................................................. 10
3. MECHANISM ........................................................................................................... 13
3.1 Remove Covers and the Lower Front Panel ....................................................... 13
3.2 Replacing the LCD Panel Module ........................................................................ 15
3.3 Replacing the Power Supply Unit ........................................................................ 16
3.4 Replacing Multi-interface Board .......................................................................... 17
3.5 Replacing the Main Board .................................................................................... 18
3.6 Replacing the Platen Roller Assembly ................................................................ 19
3.7 Replacing the Stepping Motor ............................................................................. 20
3.8 Replacing the Print head ASS'Y .......................................................................... 21
3.9 Replacing the Gap/Black Mark Sensor Module .................................................. 23
3.10 Replacing the Media Damper ............................................................................. 24
3.11 Replacing the Ribbon Rewind Spindle .............................................................. 25
3.12 Cutter Module Installation (Option) ................................................................... 26
3.13 Peel-off Kit Installation (Option) ........................................................................ 27
3.14 Internal Rewinding Kit Installation (Option) ..................................................... 31
4. TROUBLESHOOTING ............................................................................................. 35
4.1 Common Problems ............................................................................................... 35
4.2 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles ................................... 40
5. MAINTENANCE ....................................................................................................... 42
UPDATE HISTORY ...................................................................................................... 44
i
TTP-2410M/346M/644M
1. FUNDAMENTAL OF THE SYSTEM
1.1. Overview
Front View
4 6
1. LED indicators
2. LCD display
3. Front panel buttons
4. Paper exit chute
5. Lower front cover
6. Printer right side cover
1
TTP-2410M/346M/644M
Interior View
7
1
8
2
9
4
10
5
11
6 12
1. Ribbon rewind spindle 13

2. Ribbon release button
3. Ribbon guide plate
4. Print head
5. Platen roller 14
6. Print head release lever
7. Media guide bar 15
8. Label roll guard
9. Label supply spindle
10. Ribbon supply spindle
11. Damper
16
12. Label guide
13. Z axis mechanism adjustment knob
14. Print head pressure adjustment knob
15. Print head secure screw
16. Ribbon sensor
17
17. Media sensor
2
TTP-2410M/346M/644M
Rear View
2
7
3
8
4 9
10
5
1. Fan-fold paper entrance chute

2. Centronics interface
3. USB interface
4. RS-232C interface
5. Power jack socket
6. GPIO interface
7. SD card slot
8. Ethernet interface
9. PS/2 interface
10. Power switch
Note:
1. SD card slot, Ethernet interface and PS/2 interface are standard interfaces for
TTP-2410M/TTP-346M models, but optional for TTP-246M Plus/TTP-344M Plus models.
2. GPIO interface card includes SD card slot, Ethernet and PS/2 interfaces. So GPIO interface is
an factory option for TTP-2410M/TTP-346M, but a dealer option for TTP-246M Plus/TTP-344M
Plus models.
3. Recommended SD card specification.
3
TTP-2410M/346M/644M
SD card spec SD card capacity Approved SD card manufacturer
V1.0, V1.1 128 MB SanDisk, Transcend
V1.0, V1.1 256 MB SanDisk, Transcend, Panasonic
V1.0, V1.1 512 MB SanDisk, Transcend, Panasonic
V1.0, V1.1 1 GB SanDisk, Transcend, Panasonic
V2.0 SDHC CLASS 4 4 GB
V2.0 SDHC CLASS 6 4 GB SanDisk, Transcend, Panasonic
V1.0, V1.1 microSD 128 MB Transcend, Panasonic
V1.0, V1.1 microSD 256 MB Transcend, Panasonic
V1.0, V1.1 microSD 512 MB Panasonic
V1.0, V1.1 microSD 1 GB Transcend, Panasonic
V2.0 SDHC CLASS 4 microSD 4 GB Panasonic
V2.0 SDHC CLASS 6 microSD 4 GB Transcend
V1.0, V1.1 miniSD 128 MB Transcend, Panasonic
V1.0, V1.1 miniSD 1 GB Transcend, Panasonic
V2.0 SDHC CLASS 4 miniSD 4 GB Transcend
V2.0 SDHC CLASS 6 miniSD 4 GB
- The DOS FAT file system is supported for the SD card.
- Folders/files stored in the SD card should be in the 8.3 filename format
- The miniSD/microSD card to SD card slot adapter is required.
4
TTP-2410M/346M/644M
2. ELECTRONICS
2.1 Summary of Board Connectors
Main board
13
1
6
5
14
3
15
8
9
10 11 12 16
Connector Description
1 Centronics port connector

2 USB connector
3 RS-232C connector
4 LCD panel connector
5 Multi-interface board connector/ GPIO interface board
6 Micro processor
5
TTP-2410M/346M/644M
7 RFID module connector
Head open sensor connector
Pin Description Voltage

1 Head open sensor emitter
1.2~1.4V
power pin
8
2 GND 0V
3 0V: Head close
Head open sensor receiver
3.3V: Head open
4 GND 0V
Gap sensor connector

1 GND 0V
2 Gap and black mark
9 A/D: 0~3.3V
sensor receiver
3 4.0~4.1V: Emitter on
Black mark sensor emitter
4.3~4.4V: Emitter off
Gap sensor emitter
5 Power 5V
Ribbon sensor connector

Ribbon sensor emitter
10 4.3~4.4V: Emitter off
2 GND 0V
3 Ribbon sensor emitter
5V
power pin
4 Ribbon sensor receiver A/D: 0~3.3V
Ribbon encoder sensor connector

11 Ribbon encoder sensor
1 4.0~4.15V
emitter power pin
Ribbon encoder sensor
2 A/D: 0~3.3V
receiver
3 GND 0V
6
TTP-2410M/346M/644M
Cutter/peel-off sensor connector

1 0V: Cutter work
Cutter enable
5V: Cutter stop
2 0V: Cutter positive cut
Cutter direction
5V: Cutter negative cut
3 Cutter position sensor 0V: Cutter stop
12
switch 3.3V: Cutter work
4 Peel sensor receiver A/D: 0~3.3V
Peel sensor emitter
6 Logic power 5V
7 GND 0V
8 Cutter power 24V
13 Power supply output (24V DC) connector

14 GPIO interface power (24V DC) connector
15 Print head connector
16 Stepping motor connector
7
TTP-2410M/346M/644M
Multi-interface board
2
3 4
Connector Description Remark

1 Main board connector
2 SD card slot
3 Ethernet RJ-45 connector
4 PS/2 connector
8
TTP-2410M/346M/644M
GPIO with multi-interface board
3
4 5
1
Connector Description Remark

1 GPIO connector
2 Main board connector
3 SD card slot
4 Ethernet RJ-45 connector
5 PS/2 connector
6 GPIO power connector
9
TTP-2410M/346M/644M
2.2 Interface Pin Configuration
RS-232C
PIN CONFIGURATION
1 +5 V
2 TXD
3 RXD
4 CTS
5 GND
6 RTS
7 N/C
8 RTS
9 N/C
USB
PIN CONFIGURATION
1 N/C
2 D-
3 D+
4 GND
Centronics
Pin SPP Mode Nibble In/Out Function

A low on this line indicates that there are valid data
at the host. When this pin is de-asserted, the +ve
1 Strobe N/A In
clock edge should be used to shift the data into the
device.
2-9 Data 0-7 N/A In Data Bus. Single-directional.
A low on this line indicates that there are valid data
at the Device. When this pin is de-asserted, the +ve
10 Ack N/A Out
clock edge should be used to shift the data into the
host.
When in reverse direction, a high indicates data,
11 Busy N/A Out
while a low indicates a command cycle. In forward
10
TTP-2410M/346M/644M
direction, it functions as PtrBusy.
Paper Out /
12 N/A Out When low, device acknowledges reverse request.
End
13 Select N/A Out Extensibility flag
14 Ground N/A GND
15 No Defined N/A N/A
16-17 Ground N/A GND Ground
A low set by the device indicates that the reverse
32 Error / Fault N/A Out
data is available
Ethernet
PIN CONFIGURATION
1 Tx+
2 Tx-
3 Rx+
4 N/C
5 N/C
6 Rx-
7 N/C
8 N/C
PS/2
PIN CONFIGURATION
1 KBD Clock
2 GND
3 KBD Data
4 N/C
5 +5V(VCC)
6 N/C
11
TTP-2410M/346M/644M
GPIO
12
TTP-2410M/346M/644M
3. MECHANISM
3.1 Remove Covers and the Lower Front Panel
3. Remove two screws from rear of printer.
Screws
2. Open printer right side cover and remove two screws then close the cover.
Screws
3. Push the printer left side electronics cover toward the interface direction then take it out
from the printer. Please refer to the following pictures.
13
TTP-2410M/346M/644M
Electronics cover
4. Remove 3 screws from each hinge. Be careful the right side cover may fall out from the
printer. Take out the right side cover from the printer.
Screws
5. Remove 2 screws to remove lower front panel.
Screws
6. Reassemble the parts in the reverse procedures.
14
TTP-2410M/346M/644M
3.2 Replacing the LCD Panel Module
1. Refer to section 3.1 to remove the electronics cover.

2. Disconnect harness from the LCD panel module.
3. Push two tabs to remove/replace the LCD panel module.
LCD panel
module
4. Remove five screws to remove/replace LCD panel PCB ASSY and LCD panel ASSY.
LCD panel PCB assembly
15
TTP-2410M/346M/644M
3.3 Replacing the Power Supply Unit

2. Disconnect all connectors on the power supply unit.
3. Remove 2(TTP-2410M/346M) / 4(TTP-246M Plus/344 Plus) screws and 2 cable ties.
TTP-2410M/346M TTP-246M Plus/344M Plus
---- Connector
---- Screw
---- Cable tie
4. Remove/Replace the power supply unit.

Note: Replacing the power supply unit for TTP-2410M/ TTP-346M/ TTP-644M, please
use the come with new power supply cable to replace the power supply unit.
The power supply unit and its cable are compatible.
16
TTP-2410M/346M/644M
3.4 Replacing Multi-interface Board

2. Remove 4 screws then take off the interface plate.
Screws Interface
plate
3. Remove 2 screws.
Screws
4. Replace the multi-interface board.
Copper pillar
Multi-interface
Connector board
17
TTP-2410M/346M/644M
3.5 Replacing the Main Board

(Refer to section 3.4 to remove the multi-interface board.)
2. Disconnect all connectors from the main board.
3. Remove 5 screws from the main board.
(Remove 2 copper pillars and 3 screws.)
Screws or Screws
copper pillars
4. Remove/Replace the main board.
Main board
18
TTP-2410M/346M/644M
3.6 Replacing the Platen Roller Assembly
1. Open printer right side cover.

2. Disengage print head lift lever.
3. Refer to section 3.1 to remove the lower front panel.
4. Remove 2 screws from the platen holder.
Screws
5. Take out the platen holder, platen roller assembly and replace a new platen roller
assembly.
Platen roller assembly
Holder
19
TTP-2410M/346M/644M
3.7 Replacing the Stepping Motor

2. Disconnect the stepping motor connector from the main board.
Stepping motor
connector
3. Remove 2 screws on the stepping motor.
Screws
4. Remove/Replace the stepping motor.

20
TTP-2410M/346M/644M
3.8 Replacing the Print head ASSY
1. Open the printer right side cover.

2. Turn the two print head pressure adjustment knobs counterclockwise to lowest index
to minimize the pressure applied to the print head.
3. Disengage print head release lever.
4. Loose the print head secure screw counterclockwise until it can be taken out from the
mechanism.
5. Carefully disconnect connector from the print head ASSY. Please do not pull the cable to
right and left side alternatively in order to disconnect it from the print head connector.
Please use the flat screw driver to push at the key in the middle of the connector. When
the connector becomes loose from the print head connector, you can disconnect it.
6. Remove/Replace the print head ASSY.

7. Connect the print head cable and carefully slide assembly into the print mechanism. Make
sure the two locating protrusions on the print mechanism mounting plate snap into the
locating holes on the print head.
---- Locating protrusions
---- Locating holes
21
TTP-2410M/346M/644M
8. Check the print head has been totally closed to the print mechanism before secure the
print head by the previously removed thumbscrew.
Note: Please use the come with new print head secure screw to replace the print head
assembly. DO NOT use the original screw.
22
TTP-2410M/346M/644M
3.9 Replacing the Gap/Black Mark Sensor Module

2. Disconnect the gap/black mark sensor connector from the main board.
Gap/black mark
sensor connector

4. Pull the media sensor module to the end of mechanism.
5. At the bottom of the gap/black mark sensor module, there is a green plastic tab to latch
the sensor module to the mechanism. Push up the tab then pull out the gap/black mark
sensor module.
PUSH UP TAB
6. Remove/Replace the gap/black mark sensor.

23
TTP-2410M/346M/644M
3.10 Replacing the Media Damper

2. Remove the screw that fixes the damper to the mechanism.
Screw Media damper
3. Remove/Replace the media damper.

24
TTP-2410M/346M/644M
3.11 Replacing the Ribbon Rewind Spindle

2. Remove 1 E-ring.
E-ring
3. Remove the ribbon rewind spindle gear.
Ribbon rewind
spindle gear
4. Remove the E-ring that fixes the spindle at the mechanism.
E-ring
5. Remove/Replace the ribbon rewind spindle.

25
TTP-2410M/346M/644M
3.12 Cutter Module Installation (Option)

3. Plug the cutter mini DIN cable connector into the cutter/peel-off connector. The triangle
mark on the connector must be at the upper side.
4. Attach the cutter module to the front of the platen roller. Align the cutter bracket screw
holes to the screw holes that fix the lower front panel.
5. Fasten the 2 screws at the cutter bracket to fix the cutter module to the printer
mechanism.
26
TTP-2410M/346M/644M
3.13 Peel-off Kit Installation (Option)
Peel-off kit parts list:

2. Fasten the screw#2 to fix the gear#1.
Gear#1
position
Screw#2
27
TTP-2410M/346M/644M
Gear#2
position
4. Put the bearing into the internal rewind hole.
Internal rewind
hole (Left side) Bearing

6. Remove the dustproof cover from the internal rewind hole and put the bearing into it.
Internal rewind Bearing

hole (Right side)
7. Insert the internal rewind into the hole.
28
TTP-2410M/346M/644M
8. Use the E-ring driver and hammer to fix the internal rewind by E-ring.
*How to assemble e-ring?

a. Put E-ring into E-ring driver.
b. Put the E-ring on roller niche.
c. Use hammer to fix e-ring and roller.
29
TTP-2410M/346M/644M
9. Insert the gear (with spring) into the spindle and fix it with E-ring.
Gear with E-ring

spring

11. Plug the peel-off mini DIN cable connector into the cutter/peel-off connector and place
the cable in the cable cavity. The triangle mark on the connector must be at the upper
side.
12. Attach the peel-off module to the front of the platen roller. Align the peel-off module screw
holes to the screw holes that fix the lower front panel.
13. Fasten the 2 screws at the peel-off module to fix the peel-off module to the printer
mechanism.
Screw
Screw
30
TTP-2410M/346M/644M
3.14 Internal Rewinding Kit Installation (Option)
Internal rewinding kit parts list:

Gear#1
position
Screw#2

31
TTP-2410M/346M/644M
Gear#2
position
4. Put the bearing into the internal rewind hole.
Internal rewind
hole (Left side) Bearing

6. Remove the dustproof cover from the internal rewind hole and put the bearing into it.
Internal rewind Bearing

hole (Right side)
7. Insert the internal rewind into the hole.
32
TTP-2410M/346M/644M
8. Use the E-ring driver and hammer to fix the internal rewind by E-ring. (Please refer to the
section 3.13 for How to assemble e-ring?)
9. Insert the gear (with spring) into the spindle and fix it with E-ring.
Gear with E-ring

spring

11. Fasten the 2 screws to fix the label redirect front panel to the printer mechanism.
Screw
Screw
33
TTP-2410M/346M/644M
4. TROUBLESHOOTING
4.1 Common Problems
The following guide lists the most common problems that might be encountered when
operating this bar code printer. If the printer still does not function after all suggested
solutions have been invoked, please contact the Customer Service Department of your
purchased reseller or distributor for assistance.
Problem Possible Cause Recovery Procedure

Power indicator does * The power cord is not properly * Plug the power cord in printer and outlet.
not illuminate connected. * Switch the printer on.
Carriage Open
* The printer carriage is open. * Please close the print carriage.
No Ribbon * Running out of ribbon.

* Supply a new ribbon roll.
* The ribbon is installed incorrectly.
* The ribbon sensor is not been well * Please refer to the steps in users manual to
calibrated. reinstall the ribbon.
No Paper * Running out of label. * Supply a new label roll.

* The label is installed incorrectly. * Please refer to the steps in users manual to
* Gap/black mark sensor is not reinstall the label roll.
calibrated. * Calibrate the gap/black mark sensor.
Paper Jam * Gap/black mark sensor is not set

properly.
* Calibrate the gap/black mark sensor.
* Make sure label size is set properly.
* Set label size correctly.
* Labels may be stuck inside the printer
mechanism.
Take Label * If the peeler module is installed, please remove

the label.
* Peel function is enabled. * If there is no peeler module in front of the printer,
please switch off the printer and install it.
* Check if the connector is plugging correctly.
35
TTP-2410M/346M/644M
* If the cutter module is installed, please press UP
or DOWN key to rotate the cutter up or down to
UP: Fwd. * Cutter jam. make the knife back to the right position.
DOWN: Rev. * There is no cutter installed on the * Remove the label.
printer. * Make sure the thickness of label is less than 200
MENU: Exit * Cutter PCB is damaged. g/m2 (for regular cutter) or 300 g/m2 (for heavy
duty cutter).
* Replace a cutter PCB.
* Re-connect cable to interface.
* If using serial cable,
- Please replace the cable with pin to pin
connected.
- Check the baud rate setting. The default baud
rate setting of printer is 9600,n,8,1.
* If using the Ethernet cable,
- Check if the Ethernet RJ-45 connector green
LED is lit on..
- Check if the Ethernet RJ-45 connector amber
LED is blinking.
- Check if the printer gets the IP address when
using DHCP mode.
- Check if the IP address is correct when using
* Cable is not well connected to serial or the static IP address.
USB interface or parallel port. - Wait a few seconds let the printer get the
Not Printing
* The serial port cable pin configuration communication with the server then check the
is not pin to pin connected. IP address setting again.
* Chang a new cable.
* Ribbon and media are not compatible.
* Verify the ribbon-inked side.
* Reload the ribbon again.
* Clean the printhead.
* The print density setting is incorrect.
* Printheads harness connector is not well
connected with printheat. Turn off the printer
and plug the connector again.
* Check if the stepping motor is plugging in the
right connector.
* Check your program if there is a command
PRINT at the end of the file and there must have
CRLF at the end of each command line.
* Delete unused files in the FLASH/DRAM.
* The max. numbers of file of DRAM is 50 files.
* The max. user addressable memory space of
Memory full DRAM is 256 KB
* The space of FLASH/DRAM is full. * The max. numbers of file of FLASH is 256 files.
( FLASH / DRAM ) * The max. user addressable memory space of
FLASH is 2560 KB for TTP-246M Plus and
TTP-344M Plus and 6656KB for TTP-2410M
and TTP-346M.
36
TTP-2410M/346M/644M
* Use the supported capacity SD card.
* Insert the SD card again.
* The supported SD card spec.
* SD card is damaged. - 128MB
SD card is unable to * SD card doesnt insert correctly. - 256MB
use * Use the non-approved SD card - 512MB
manufacturer. - 1GB
- 4GB SDHC CLASS 6
* Approved SD card manufacturers; SanDisk,
Transcend
* Did not turn off power prior to plug in * Turn off printer power prior to plug in the PS/2
the PS/2 keyboard keyboard .
PS/2 port does not * PS/2 keyboard is damaged. * Plug the PS/2 keyboard again.
work * PS/2 keyboard doesnt plug-in * Make sure the keyboard is fine.
correctly. * Make sure if there is any BAS file downloaded
* There is no BAS file in the printer. into printer.
* Reload the supply.
* Clean the printhead.
* Clean the platen roller.
* Adjust the print density and print speed.
* Run printer self-test and check the print head
test pattern if there is dot missing in the pattern.
* Change proper ribbon or proper label media.
* Adjust the printhead pressure adjustment knob.
- If the left side printout is too light, please adjust
the left side pressure adjustment knob to the
* Ribbon and media is loaded incorrectly
higher index (higher pressure). If the pressure
* Dust or adhesive accumulation on the
adjustment knob has been adjust to index 5
print head.
and the poor print quality is still at the left side
* Print density is not set properly.
Poor Print Quality of the printout, please adjust the pressure
* Printhead element is damaged
adjustment knob to index 1 and use the
* Ribbon and media are incompatible.
Z-axis adjustment knob to fine tune the
* The printhead pressure is not set
pressure.
properly
- If the right side printout is too light, please
adjust the right side pressure adjustment knob
to the higher index (higher pressure) to
improve the print quality.
* If the label thickness is more than 0.22 mm, the
print quality might be good enough, please
adjust the heater line adjustment screw counter
clockwise to get the best print quality.
* The release lever does not latch the printhead
properly.
LCD panel is dark and * The cable between main PCB and LCD * Check if the cable between main PCB and LCD
keys are not working. panel is loose. is secured or not.
LCD panel is dark but * The printer initialization is * Turn OFF and ON the printer again.
the LEDs are light. unsuccessful. * Initialize the printer.
LCD panel is dark and

LEDs are lit on, but * The LCD panel harness connector is * The LCD panel harness connector is plugged
the label is feeding loose. upside down.
forward.
37
TTP-2410M/346M/644M
Ribbon encoder * The ribbon encoder sensor connector
* Fasten the connector.
sensor doesnt work. is loose.
Ribbon end sensor * The connector is loose.
* Check the connector.
* The ribbon sensor hole is covered with
doesnt work. * Clear the dust in the sensor hole by the blower.
dust.
Peel sensor is not * Peel sensor is not located on the * Make sure that the media goes through the Peel
correct position. sensor.
working. * The connector is loose. * Plug the connect cable correctly.
Cutter is not working. * The connector is loose. * Plug in the connect cable correctly.
Label feeding is not * If the label is moving to the right side, please
* The media guide does not touch the move the label guide to left.
stable (skew) when
edge of the media. * If the label is moving to the left side, please
printing. move the label guide to right.
* Check if label size is setup correctly.
Skip labels when * Label size is not specified properly.
* Calibrate the sensor by Auto Gap or Manual
* Sensor sensitivity is not set properly.
printing. Gap options.
* The media sensor is covered with dust.
* Clear the GAP/Black mark sensor by blower.
* Calibrate the sensor sensitivity again.
* Set the correct label size and gap size.
* Press [MENU] [SELECT] x3[DOWN]x6
[SELECT] to fine tune the parameter of Shift Y.
* If using the software BarTender, please set the
vertical offset in the driver.
* Media sensor sensitivity is not set

properly.
The printing position
* Label size is incorrect.
of small label is * The parameter Shift Y in the LCD menu
is incorrect.
incorrect. * The vertical offset setting in the driver is
incorrect.
* Set the correct label size.

The left side printout * Wrong label size setup. * Press [MENU] [SELECT] x 3 [DOWN] x 5
* The parameter Shift X in LCD menu is
position is incorrect. incorrect. [SELECT] to fine tune the parameter of Shift
X.
Missing printing on
the left or right side of * Wrong label size setup. * Set the correct label size.
label.
38
TTP-2410M/346M/644M
RTC time is incorrect
when reboot the * The battery has run down. * Check if there is a battery on the main board.
printer.
Multi interface board * Check if the board is plugged in the right
* The installation is incorrect.
doesnt work. connector.
Power and Error LEDs * Turn off the printer and wait all LEDs are dark,
* Power switch OFF and ON too fast.
are blinking fast. and turn on the printer again.
* Printhead pressure is incorrect. * Please refer to the 5.2 chapter.
* Ribbon installation is incorrect. * Please set the suitable density to have good
Wrinkle Problem * Media installation is incorrect. print quality.
* Print density is incorrect. * Make sure the label guide touch the edge of the
* Media feeding is incorrect. media guide.
Gray line on the blank * The printhaed is dirty. * Clean the printhead.
label * The platen roller is dirty. * Clean the platen roller.
* Turn off and on the printer to skip the dump
* The printer is in Hex Dump mode.
Irregular printing mode.
* The RS-232 setting is incorrect.
* Re-set the Rs-232 setting.
39
TTP-2410M/346M/644M
4.2 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles
This printer has been fully tested before delivery. There should be no ribbon wrinkle
presented on the media for general-purpose printing application. Ribbon wrinkle is related to
the media thickness, print head pressure balance, ribbon film characteristics, print darkness
settingetc. In case the ribbon wrinkle happens, please follow the instructions below to
adjust the printer parts.
Print head pressure

adjustment knob Z-axis mechanism
adjustment knob
Adjustable
Printer
Ribbon guide plate
Parts
1. Wrinkle happens from label lower left to 2. Wrinkle happens from label lower right
Symptom
upper right direction () to upper left direction ()
Wrinkle
Example
Feed direction
40
TTP-2410M/346M/644M
Adjust the print head pressure adjustment knob Adjust the print head pressure adjustment knob
Left knob Right knob Left knob Right knob
The print head pressure adjustment knob has 5 The print head pressure adjustment knob has 5
levels of settings. Clockwise direction adjustment levels of settings. Clockwise direction adjustment
is to increase the print head pressure. Counter is to increase the print head pressure. Counter
Clockwise adjustment can decrease the print Clockwise adjustment can decrease the print
head pressure. head pressure.
If the wrinkle on the label starts from the lower left If the wrinkle on the label starts from the lower
side to upper right side, please do following right side to upper left side, please do following
adjustment. adjustment.
1. Decrease the right side print head pressure 1. Decrease the left side print head pressure
adjustment knob setting 1 level per each adjustment knob setting 1 level per each
adjustment then print the label again to check if adjustment then print the label again to check if
wrinkle is gone. wrinkle is gone.
2. If the right side print head adjustment knob 2. If the left side print head adjustment knob level
setting has been set to index 1 (the lowest has been set to index 1 (the lowest index),
pressure index), please increase the left side please increase the right side print head
print head pressure. pressure.
3. If the left side print head adjustment knob
setting has been set to 5 (the highest pressure
index) the wrinkle cant be avoid, please rotate
the both knobs back to setting 1 then rotate the
Z-axis mechanism adjustment knob clockwise
for a few degrees and print again for fine tune
the print head pressure distribution.
Z axis mechanism
adjustment knob
Note for step 3:

*Factory default setting, the Z-axis knob is rotated
counter clockwise to the end of thread.
*Turn the Z-axis mechanism adjustment knob
clockwise until you feel the knob touch the
mechanism for the first adjustment.
* If the wrinkle is still there, please turn the Z-axis
mechanism adjustment knob clockwise about
1/4 circle each time for adjustment
* If the winkled direction is change from to
by adjusting the Z-axis mechanism
adjustment knob, please turn the Z axis
mechanism adjustment knob counter clockwise
to avoid the wrinkle. 41
TTP-2410M/346M/644M
5. MAINTENANCE
This session presents the clean tools and methods to maintain your printer.
3. Please use one of following material to clean the printer.

Cotton swab (Head cleaner pen)
Lint-free cloth
Vacuum / Blower brush
100% ethanol
2. The cleaning process is described as following

Printer Part Method Interval
1. Always turn off the printer Clean the print head when changing a
before cleaning the print head. new label roll
2. Allow the print head to cool for
a minimum of one minute.
3. Use a cotton swab (Head
cleaner pen) and 100% ethanol
to clean the print head surface.
Print Head
1. Turn the power off. Clean the platen roller when changing
2. Rotate the platen roller and a new label roll
Platen Roller wipe it thoroughly with 100%
ethanol and a cotton swab, or
lint-free cloth.
Tear Bar/Peel Use the lint-free cloth with 100% As needed
42
TTP-2410M/346M/644M
Bar ethanol to wipe it.
Sensor Compressed air or vacuum Monthly
Wipe it with water-dampened As needed
Exterior
cloth
Interior Brush or vacuum As needed
Note:
Do not touch printer head by hand. If you touch it careless, please use ethanol to clean
it.
Please use 100% Ethenol. DO NOT use medical alcohol, which may damage the printer
head.
Regularly clean the print head and supply sensors once change a new ribbon to keep
printer performance and extend printer life.
43
TTP-2410M/346M/644M
UPDATE HISTORY
Date Content Editor
Modify electronics cover part no. from 32-0240004-00LF to
2007/12/4 Camille
98-0240031-00LF.
2007/12/5 Add internal rewinding kit part no. (Option). Camille
Modify description for 98-1000011-00LF External wireless Camille
2008/1/24 print server / US & 98-1000012-00LF External wireless print
server / EU
2008/2/19 Modify the print head module part number. (Add screw) Camille
2008/2/22 Add 2.4 section: Internal Rewinding Kit Installation (Option) Camille
2008/2/29 Add print head module (TTP-644M) and peel-off sensor assy Camille
part number
2008/3/7 Modify the Maintenance section Camille
2008/3/12 Modify the Troubleshooting section Camille
2008/3/21 1.Add print head harness (TTP-644M) part number Camille
2.Update the LCD panel board assembly part no. from -00LF
to -10LF
3.Update the interface plate part no. from -00LF to -10LF
2008/4/29 Update the Multi-interface board part no. from -01LF to -11LF Camille
2008/6/23 Remove the part list section Camille
2008/10/3 Modify the 3.9 section Camille
2008/11/20 Modify the 3.7 section (Replacing the stepping motor) Camille
2009/3/16 Modify section 1.1 (Recommended SD card specification) Camille
2009/4/15 Modify section 3.13 & 3.14 (Peel-off kit installation & Internal Camille
rewinding kit installation)
2009/9/25 Modify section 2.1 Camille
2011/1/25 Modify TSC address Camille
2012/3/1 Modify section 3.3 (Note for replacing the power supply unit) Cinya
44
Corporate Headquarters Li Ze Plant
9F., No.95, Minquan Rd., Xindian Dist., No.35, Sec. 2, Ligong 1st Rd., Wujie Township,
New Taipei City 23141, Taiwan (R.O.C.) Yilan County 26841, Taiwan (R.O.C.)
TEL: +886-2-2218-6789 TEL: +886-3-990-6677
FAX: +886-2-2218-5678 FAX: +886-3-990-5577
Web site: www.tscprinters.com
TSC Auto ID Technology Co., Ltd. E-mail: [email protected]
[email protected]
45

TTP-2410M Service Manual E

Uploaded by

Copyright:

Available Formats

TTP-2410M Service Manual E

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TTP-2410M Service Manual E

Uploaded by

Copyright:

Available Formats

What are the main sections covered in the manual?

What are the main sections covered in the manual?

What components can be replaced according to the manual?

What components can be replaced according to the manual?

TTP-2410M/346M/644M

TTP-246M Plus/344M Plus

THERMAL TRANSFER / DIRECT THERMAL

1. FUNDAMENTAL OF THE SYSTEM

1. Ribbon rewind spindle 13

1. Fan-fold paper entrance chute

1 Centronics port connector

Pin Description Voltage

Gap sensor connector

Pin Description Voltage

Ribbon sensor connector

Pin Description Voltage

Ribbon encoder sensor connector

Pin Description Voltage

Pin Description Voltage

13 Power supply output (24V DC) connector

Connector Description Remark

Connector Description Remark

Pin SPP Mode Nibble In/Out Function

3.1 Remove Covers and the Lower Front Panel

3. Remove two screws from rear of printer.

5. Remove 2 screws to remove lower front panel.

6. Reassemble the parts in the reverse procedures.

1. Refer to section 3.1 to remove the electronics cover.

LCD panel PCB assembly

5. Reassemble the parts in the reverse procedures.

1. Refer to section 3.1 to remove the electronics cover.

TTP-2410M/346M TTP-246M Plus/344M Plus

4. Remove/Replace the power supply unit.

1. Refer to section 3.1 to remove the electronics cover.

4. Replace the multi-interface board.

5. Reassemble the parts in the reverse procedures.

1. Refer to section 3.1 to remove the electronics cover.

4. Remove/Replace the main board.

5. Reassemble the parts in the reverse procedures.

1. Open printer right side cover.

Platen roller assembly

6. Reassemble the parts in the reverse procedures.

1. Refer to section 3.1 to remove the electronics cover.

3. Remove 2 screws on the stepping motor.

4. Remove/Replace the stepping motor.

1. Open the printer right side cover.

TTP-2410M/346M TTP-246M Plus/344M Plus

6. Remove/Replace the print head ASSY.

TTP-2410M/346M TTP-246M Plus/344M Plus

9. Reassemble the parts in the reverse procedures.

1. Refer to section 3.1 to remove the electronics cover.

3. Open the printer right side cover.

6. Remove/Replace the gap/black mark sensor.

1. Open the printer right side cover.

Screw Media damper

3. Remove/Replace the media damper.

1. Refer to section 3.1 to remove the electronics cover.

3. Remove the ribbon rewind spindle gear.

4. Remove the E-ring that fixes the spindle at the mechanism.

5. Remove/Replace the ribbon rewind spindle.