SMV PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 29

Procedure for installing

Service Manual Viewer


and Service Manual data

SMV.pdf
Contents

Chapter 1 System requirements for installation of Service Manual Viewer ---- 2

Chapter 2 Procedure for installing ------------------------------------------------------------ 3


2.1 Flow of installation------------------------------------------------------------------- 3
2.2 Procedure for installing Service Manual Viewer--------------------------- 4
2.3 Procedure for installing Service Manual data ------------------------------ 9
2.3.1 Preparation of installing Service Manual data------------------------------ 9
2.3.2 Installation of Service Manual data--------------------------------------------- 12

Chapter 3 Procedure for uninstalling--------------------------------------------------------- 20


3.1 Flow of uninstallation --------------------------------------------------------------- 20
3.2 Procedure for uninstalling Service Manual data -------------------------- 21
3.3 Procedure for uninstalling Service Manual Viewer ----------------------- 25

Chapter 4 Notes of use only for Windows2000 and WindowsXP------------------- 28


4.1 Account in which SMV use is possible --------------------------------------- 28

1
Chapter 1 System requirements for installation of Service Manual Viewer

(1) Hardware
Operating system : Windows2000 or WindowsXP
Caution: The recommended OS is English version in this installer.
When you use OS in other languages, some characters may be garbled.
There is no problem on the system, so you can keep installing.

RAM : More than recommended value of operating system (Windows98 : 32MB or more)
Hard disk : Service Manual Viewer system
10MB of available hard-disk space
Hard drive utilization of the Service Manual data
(1) Database for the Service Manual search approx. 20MB *1
(2) Service manual data approx. 250MB *1

Display : Greater than 800X600 pixels resolution and 256 colors

(2) Software
Microsoft Internet Explorer 5.5 or 6.0
Acrobat Reader 5.0 or later

Trademarks
Microsoft, Windows2000, WindowsXP and Internet Explorer are registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
Acrobat Reader Copyright 1987-2001 Adobe Systems Incorporated. All rights
reserved.Adobe, Adobe logo, Adobe Acrobat and Adobe Acrobat logo are trademarks of Adobe
Systems Incorporated.

2
Chapter 2 Installation procedure

2.1 Flow of installation


Caution: In case of Windows2000 and WindowsXP, installation must be started
after login by a user who has authority of the Administrator.

Start

Installation into
Windows2000 Yes
and
WindowsXP Login by a user who has
authority of the
No Administrator

2.2. Installing Service


Manual Viewer

The set location for installation is the


Restarting PC same folder as the system.
Recommendation:
If there is enough space on another
drive, change of location for
installation is recommended.
Change of location
where Service
Manual (S/M) datal is
installed
No
Yes

2.3.1. Preparating
S/M installation

2.3.2. Installing Service


Manual data

Complete

3
2.2 Procedure for installing Service Manual Viewer

Caution: Exit all of other applications before installing.


Some data may be lost because of restarting PC after completing installation.

(1) When you set CD-ROM in CD drive, installation is automatically started.


Go to (2) on this page.

In case that installation is not started, right-click Start at the lower-left corner of the desktop and click
Explore. (Refer to Figure1)
Then double-click AUTORUN.exe in the CD. (Refer to Figure2)

Figure 1: Running Explore

Figure 2: Running AUTORUN.exe

(2) Dialog box for confirmation of Service Manual (S/M) Viewer installation (Figure 3) appears. Click Yes.

Figure 3: Dialog box for confirmation of S/M Viewer installation

4
(3) The dialog box for preparation (Figure 4) appears, and then the next dialog box for welcome (Figure 5)
appears.

Figure 4: InstallShield Wizard

Start to install Service Manual Viewer. Click Next. (Refer to Figure 5)

Figure 5: Starting installation

(4) Select a folder for installation. (Default : C:\Program Files)


When you change the folder, click Browse. Then the window for referring to folders appears.
(Refer to Figure 7)
Select or enter a folder, and click OK.

Caution: Appoint a folder for installation.


(e.g.: not appoint X :\ . X is drive name.)

After selecting a folder, click Next.

Figure 6: Selecting a folder for installation

5
Figure 7: Referring to folders for installation

(6) Select language for introduction, and click Next.

Figure 8: Selecting the introduction language

(7) Select language for use, and click Next.

Figure 9: Selecting the use language

6
(8) Installation of the Service Manual Viewer is started. (Refer to Figure 10)

Caution: Wait for a while until setup is completed properly,


even if Setup status reached 100%.

Figure 10: Setup Status window (at installation)


When the window for completion appears, select Yes, I want to restart my computer now, and click
Finish. (Refer to Figure 11)

Figure 11: Completing installation

7
After restarting PC, the shortcut icon appears on the desktop. (Refer to Figure 12)

Figure 12: Shortcut icon

Double-click the shortcut icon (Figure 12) to start the Service Manual main menu. (Refer to Figure 13)

Figure 13: Screen of the Service Manual main menu

You complete installing the Service Manual Viewer.

8
2.3 Procedure for installing Service Manual data

2.3.1 Preparation of installing Service Manual data

If you do not change location for installation, go to 2.3.2 Installation of Service Manual (S/M) data on page 12.

(1) Double-click the created shortcut icon (Figure 14) on the desktop to start Service Manual main menu.
(Refer to Figure 15)

Figure 14: Shortcut icon

(2) Click Maintenance in Service Manual Main Manu. (Refer to Figure 15)

Figure 15: Service Manual main menu

9
(3) Click Environment tab, and click Environmental setting change button. (Refer to Figure 16)

Figure 16: Maintenance menu

(4) Password input screen appears. (Refer to Figure 17)


Enter password SMV, and click OK.

OK button

Figure 17: Password input screen

10
(5) Environmental change screen appears. (Refer to Figure 18)

You can set any drive and any directory to install the Service Manual data.
Initial setting is the system default. e.g.: C:\Program files
When you change a local drive, click alphabet in A local drive. (Refer to Figure 18 (a))
When you change a directory, click Directory button. (Refer to Figure 18 (b) and Figure 19)

Click OK after selecting a drive and a directory. (Refer to Figure 18)

Caution: Confirm that you click OK in order to reflect Environmental


change.

(a) (b)

OK button

Figure 18: Environmental change

OK button

Figure 19: Directory change

11
2.3.2 Installation of Service Manual data

Caution: Confirm that there is enough space in the disk drive before installation.

Required disk space for installation of Service Manual (S/M) data is as follows. (Refer to Chart 1)

Chart 1: Required disk space for installation


Required disk space
DB data S/M data Remarks
Approx. 20MB - Install only DB data *1
Approx. 20MB Approx. 250MB

*1: In case that only DB data is installed, CD-ROM is required to browse the S/M data.

Caution: Exit all of other applications before installation.

(1) When you set CD-ROM in CD drive, installation is automatically started.


Go to (2) on page 13.

In case that installation is not started, right-click Start at the lower-left corner of the desktop and click
Explore. (Refer to Figure20)

Figure 20: Running EXPLORE


Then double-click AUTORUN.exe in the CD-ROM. (Refer to Figure 21)

Figure 21: Running AUTORUN.exe

12
(2) Dialog box for confirmation of S/M data installation (Figure 22) appears. Click Yes.

Figure 22: Dialog box for confirmation of S/M installation

(3)The dialog box for preparation (Figure 23) appears, and then the next dialog box for welcome (Figure 24)
appears.

Figure 23: InstallShield Wizard

Start to install Service Manual data. Click Next . (Refer to Figure 24)

Figure 24: Starting installation

13
(4) When you select a model year for installing the Service Manual data, the selected model is highlighted as
Figure 25.

After selecting, click Next. (Refer to Figure 25)

Figure 25: Selecting a model year for installation.


(5) Select location for installing the Service Manual data.

Select one of the following options.


a) Install only the DB data into a local drive
Install only the DB data into a hard disk.
In this case, make reference to the S/M data in CD-ROM.
When you browse the S/M data, CD-ROM must be set.
Select this basically.
Go to page 15.

b) Install the DB data and the Service Manual data into a local drive.
Install all data (the DB and the S/M) into a disk drive.
When you browse the S/M data, CD-ROM is not required.
Go to page 17.

Figure 26: Selecting location for installing

14
(6) Case 1 selecting Only DB data will be installed on the Local.
The image of installing the Service Manual data is as follows. (Refer to Figure 27)

Appointed location e.g. : C:\Program files

MUT3

DATA Figure 27

004 Destination code

5850202020202020 Model code (GRANDIS in this case)

2004 DB

VER Storage location of the DB data

a) Select Only DB data will be installed on the Local. ,and click Next. (Refer to Figure 28)

Figure 28: Selecting location for installation


b) Confirm that the directory for installation is displayed properly, and click Next. (Refer to Figure 29)

Figure 29: Indicating the directory for installation

15
c) After copying files (Refer to Figure 30), Setup Status window appears (Refer to Figure 31).
It takes a few minutes.

Figure 30: Copying files

Figure 31: Setup Status window

d) When the window for completion appears, click Finish. (Refer to Figure 32)

Figure 32: Completing installing

You complete installing the Service Manual data.

16
(6) Case 2 - selecting All, DB data and HTML documents will be installed on the Local.
The image of the Service Manual data is as follows. (Refer to Figure 33)

Appointed location e.g. : C:\Program files

MUT3

DATA Figure 33

004 Destination code

5850202020202020 Model code (GRANDIS in this case)

2004 DB

HTML Storage location of the DB data

CSS

SCRIPT

IMG

VER

a) Select All, DB data and HTML documents will be installed on the Local., and click Next.
(Refer to Figure 34)

Figure 34: Selecting location for installation

17
b) Confirm that the directory for installation is displayed properly, and click Next.
(Refer to Figure 35)

Figure 35: Indicating the directory for installation

c) After copying files (Refer to Figure 36), Setup Status window appears. (Refer to Figure 37)
It takes a few minutes.

Figure 37: Copying files

Figure 37: Setup Status window


Caution: Just after Setup Status window (Figure 37) is closed, InstallShield Wizard is still
displayed on the task bar. (Refer to Figure 38)
It does not mean PC freezing, so wait for a while.

Figure 38: InstallShield Wizard (task bar indication)

18
d) When the window for completion appears. click Finish .

Figure 39: Completing installation

You complete installing the Service Manual data.

19
Chapter 3 Procedure for uninstalling

3.1 Flow of uninstallation

Start

Complete to install
Service Manual No
(S/M)data

Yes

Have an installation No
CD of S/M data

Yes

3.2. Uninstalling
Service Manual data
* In case of deletion of
Service Manual Viewer,
delete all models.

Windows2000 Yes
and
WindowsXP
Login by a user who has
authority of the
No Administrator

3.3. Uninstalling
Service Manual Viewer

Restarting PC

Complete

20
3.2 Procedure for uninstalling Service Manual data

Caution: Delete Service Manual (S/M) data before deleting S/M Viewer or at re-installing S/M data.
When you do not install the S/M data into a disk drive, this process is not required.

(1) Click Maintenance button in Service Manual MAIN MENUE. (Refer to Figure 40)

Figure 40: Service Manual main menu


(2) Click Data update tab, and then click Service manual button. (Refer to Figure 41)

Figure 41: Maintenance menu (S/M data management)

21
(3) Click Service manual to be deleted button. (Refer to Figure 42)

Figure 42: Service Manual data management menu

(4) Password input screen appears. (Refer to Figure 43)


Enter password SMV, and click OK.

OK button

Figure 43: Password input screen

22
(5) The list of installed models appears. (Refer to Figure 44)
Click a model to uninstall. (In this case, 04GRANDIS for EUR.)

Figure 44: The model List

(6) The location of the selected model is displayed. (Refer to Figure 45)
Click the check boxes of the Service manual reference table and the Service manual ((a)).
Then click Delete button.

(a)

In case that only the DB data is installed, it displays


as There is no Service Manual.

Delete button

Figure 45: Screen of the location

23
(7) The dialog box for confirmation of deletion appears. (Refer to Figure 46)
Click OK. When you cancel, click Cancel button.

OK button Cancel button

Figure 46: Confirmating for deletion

(8) Returns to the screen of the list of installed models. (Refer to Figure 47)
Complete to delete the selected model.
Click and returns to the Maintenance menu screen.

Returns to Maintenance button

Figure 47: The model list

24
3.3 Procedure for uninstalling Service Manual Viewer

Caution: (1) Confirm that Service Manual Viewer does not run before uninstalling.
(2) In case of Windows2000, installation must be started after login by a user who has authority of the
Administrator.
(3) Before uninstalling the Service Manual Viewer, uninstall all of the Service Manual (S/M) data
according to 3.2. Procedure of Uninstalling Service Manual data.

Uninstallation screen is for Windows2000.


(1) Click Start, Settings and Control Panel on the desktop. (Refer to Figure 48)

Figure 48: Control Panel

(2) Double-click Add/Remove Programs icon in the Control Panel. (Refer to Figure 49)

Figure 49: Add/Remove Programs

25
(3) Add/Remove Programs window appears. (Figure 50)
Select Service manual viewer system, and click Change/Remove button.
After clicking, InstallShield Wizard is started. (Refer to Figure 51)

Figure 50: Property of Add/Remove Programs


(4) InstallShield Wizard dialog box appears (Figure 51), and then Confirm File Deletion
dialog box appears. (Refer to Figure 52)

Figure 51: Starting InstallShield Wizard


When you complete deleting the system, click OK.
When you cancel, click Cancel.

Figure 52: Confirm File Deletion

26
(5) When you click OK, Setup Status window (Figure 53) appears and the process of deletion is started.

Figure 53: Setup Status window (for uninstallation)


(6) When the process of deletion is completed, InstallShield Wizard Complete window appears.
(Refer to Figure 54)
Click Finish to restart PC.

Figure 54: Completing deletion of the system.

27
Chapter 4
Instruction of use only for Windows2000 and WindowsXP

4.1 Valid account in using SMV

Valid account in using SMV is an account of user with authority of the Administrator .

Basically, please log on with the user ID with authority of the Administrator to use SMV.
In case you can't log on with user ID with authority of the Administrator, you can log on and use SMV by
the following procedure.

If you are using Windows 2000


On logon dialogue box, input as follows and click " OK".
User name: mmcsmv
Password: mmcsmv

If you are using Windows XP


On logon dialogue box, input as follows and click " OK".
User name: mmcsmv
Password: mmcsmv

In case the welcome screen appears on the desktop, press "Ctrl" "Alt" and "Del" for twice, then log on
screen (logon dialogue box) will appear.
On Windows XP, user icons are not displayed on the welcome screen.

28

You might also like