Protective Coatings

Dr. Zuhair M. Gasem

ME Dept, KFUPM
Dhahran, Saudi Arabia

References:
1. Corrosion and Corrosion protection
handbook by A. Schweitzer
2. Corrosion Prevention by Protective
Coatings by C.G. Munger (NACE)
3. Corrosion Control by S.A. Bradford
KFUPM-ME 2
472 (062)
Coatings and Lining
The most widely used method for corrosion control
6.7 Billion dollar in 1997 for corrosion protection by
coatings
A coat is a thin protective layer, typically 50-100 m.
A lining is thick, typically 0.5-3 mm in thickness.
Linings are usually applied in the interiors of
tanks, pipes, vessels, where immersion is
continuous and corrosion is severe.
Coatings are usually applied on surfaces where
immersion is not continuous such as the external
surfaces of tanks and pipes.
KFUPM-ME 3
472 (062)
Coatings and Lining
Corrosion protection by coatings can be achieved by one of the following
mechanisms:
1. A barrier coating that prevents the corrosive environment from
reaching the base metal (thick lining).
2. A sacrificial metal coating that corrodes while giving cathodic
protection to the base metal (galvanizing).
3. A noble metal coating that ensures that the base metal is in the passive
state.
4. An inhibitor coating that slows electrode reactions.
5. An electrically resistive coating that slows down electrochemical
corrosion reactions (organic coating).

Coating
or lining

Base metal
KFUPM-ME 4
472 (062)
Coating Materials
Coatings
Materials
Organic Metallic
(Paints)
Inorganic

Conversion Porcelain Cement Inorganic

Thermoplastics How is it applied?
coatings enamels Linings Zinc/Silicates

Hot Dipping
Chromate
Elastomers (Rubber) Zn (galvanizing) Portland Cement
Al, and Pb

Electroplating
Thermosettings (Ni, Cr, Zn, Sn, Cd) Phosphate Potassium Silicate

Thermally Sprayed
Anodizing Modified Potassium
Zn-rich coatings (any metal in
Silicate
powder form)

Cladding
Calcium Aluminates
Stainless steel

Weld Overlaying
KFUPM-ME 5
472 (062)
Organic Paints

An organic paint consists of

a liquid part known as a
vehicle and a solid part.
The vehicle part consists of:
A binder or a resin (non-
volatiles, it does not
evaporate after drying)
A Solvent (volatiles)
Liquid additives
The solid part consists of
Powdery particles or
pigments
Solid additives
KFUPM-ME 6
472 (062)
Binders
A binder is an organic liquid (oil or resins) that forms a dense
and tight protective skin or film in different ways:
Oxygen reactive binders: resins forming solid film by reacting with O2.
Thermosetting resins such epoxy-esters, urethane-alkyds.
Evaporation of the solvent which leaves behind a film of the polymer
that was dissolved or suspended in water or oil based solvents.
Thermoplastic resins such as PVC and acrylics
Polymerization reaction
Mixing a resin and a hardener (thermosets)
The binder provides the basic coating properties in terms of chemical
resistance, permeability, abrasion resistance, and hardness.
KFUPM-ME
472 (062) Binders: thermoplastics 7

Thermoplastic binders:
The solid film consists of entangled linear
chains as shown in the figure.
The most common thermoplastic binders
are:
Vinyls (polyvinyl chloride and
polyvinyl acetate copolymer)
high impermeability
widely used for steel immersed
in water Poly-vinyl-
highly resistant to oil and chloride
grease
applied by spraying
Acrylics (dissolved in water or
solvents)
Highly resistant to UV
High stability of color acrylic
Excellent for protection against
atmospheric exposure
Used in cars external body
KFUPM-ME 8
472 (062)
Binders: Thermosets
Thermosetting binders:
The solid film consists of rigid 3-
dimensional network of molecules.
The most common thermoplastic
binders are:
Epoxy
excellent resistance to acid and
alkaline environments
Excellent adhesion and used as
primers
Phenolic
Poly-urethanes epoxy
UV resistant
Excellent abrasion resistant
Used in aircraft, cars,
Polyester Urethanes
Thick films (1 mm)
Excellent abrasion resistant

phenolics
KFUPM-ME 9
472 (062)
Binders: Thermosets
An example hardener Resin
showing
polymerization of
a thermosetting
Polymer
(phenolic)
KFUPM-ME 10
472 (062)
Binders: organic oils
Organic oil binders:
The solid film form after drying vegetable oils by
oxidation to form 3-dimensional network of the
oil molecules.
Takes long time to dry up (few days).
The most common oil based binders are:
Alkyd (Good resistant to atmospheric condition)
linseed oil + ALCOHOL+ ORGANIC ACID
KFUPM-ME 11
472 (062)
Binders

Zinc rich organic binders:

combination of fine powder of zinc and an organic
binder where Zn corrodes and provides galvanic
protection to steel
The binder can be any thermoplastic or
thermosetting resins such as vinyls, acrylics, or
epoxies.
Commonly used as primers
KFUPM-ME 12
472 (062)
Binders
The binder provides the following functions:
Binding the pigments together
Adherence to substrate (metal surface)
Cohesion (strength of the coat)
Flexibility to the coating film
Abrasion resistance
Anti-corrosive properties
Chemical resistance
KFUPM-ME 13
472 (062)
Solvents
Solvents are added to keep the binder in solution
during storage and to provide fluidity during
application.
Examples: aromatic hydrocarbons (toluene, xylene) ,
alcohol, ethers, esters, water in latex paints.
Solvents determine:
Application properties
Evaporation rate or drying time
Flash point
KFUPM-ME 14
472 (062)
Pigments
Pigments are solid particles in powder form that are
added to the coat to:
Produce desired color
Determine opacity
Protect the binder from UV radiation
Inhibit corrosion
Increase abrasion resistance
Increase strength and toughness
Improve coating adhesion
Examples: (Na2CrO4 , ZnPO3 , phosphates)
KFUPM-ME 15
472 (062)
Additives
Additives are small amounts of solids or
liquids that control a number of important
features such as:
speed of drying and curing
Wetting agents
Anti-skinning
Settling and sagging agents
Storage agents
KFUPM-ME 16
472 (062)
Definitions
A coat: a liquid applied as a thin layer which is
converted to a solid-protective adherent film after
DRYING.
Enamel: a coat that can form very smooth film.
Varnish: a liquid that converts to a transparent solid
film after application as a thin layer.
Lacquer: a coating composition based on
thermoplastic binders dissolved in organic solvent
that dries by solvent evaporation.
KFUPM-ME 17
472 (062)
Requirements for Good Coats
Chemical resistance
Low moisture permeability
Good adhesion
Flexibility (expand and contract with the metal substrate)
Good impact and abrasion resistance
Ease of applications
Durability
Low cost
Hence, no single coat can provide all needed properties
For example:
Coats for underground structures: resistance to abrasion
Coats for atmospheric corrosion: resistance to UV
Coats for marine environments: resistance to high humidity and Cl-
Coats to industrial environments: resistance to high temp, high acidity
We must use multiple coats to satisfy these requirements.
KFUPM-ME
472 (062) Coating System 18

Resistant to Ion penetration

Top Coat Alkali Resistant 50 m
Insulator
p Low moisture and
Intermediate 100 m
Coat vapor transfer rate
Adheres to substrate 20-50 m
Primer Resists corrosion

Metal Surface

A coating system consists of multiple layers coats.

KFUPM-ME 19
472 (062)
Coating System

Primer Coat: the coat next to the substrate.

Strong adhesion to substrate
Good adhesion to intermediate coat
Resist chemical attack
Resist water permeability
Carries corrosion inhibitor
KFUPM-ME 20
472 (062)
Coating System
Intermediate Coat: the main function is to increase
the thickness of the coat.
To reduce rate of moisture permeability
To increase chemical resistance
To Increase resistance to electricity and impact, and
abrasion
Top Coat: in contact with the electrolyte.
To provide durability
To provide color, gloss, and texture
Usually more dense but less thick than the intermediate.
KFUPM-ME 21
472 (062)
Coating Procedure
1. Surface Preparation
2. Selection of a coat system
3. Application method
4. Coating Inspection and Testing
5. Coating maintenance
6. Coating Failure
KFUPM-ME 22
472 (062)
1. Surface Preparation
Good surface preparation is essential for good coating performance.
Objectives:
To remove any foreign substance from the surface such as such as dirt, dust,
oils, chemicals, and corrosion products by one of the following methods:
solvent or chemical washing
steam cleaning
hand tool cleaning
To create a profile to provide anchor to the binder for good mechanical
adhesion. The surface roughness can be increased by:
High pressure water-blasting
Wet abrasive-blasting
Air abrasive-blasting
At least 25-50 m (1-2 mils) anchor pattern must be made to provide adhesion
to the primer.

Anchor pattern
KFUPM-ME 23
472 (062)
1. Surface Preparation

SP1 (solvent cleaning) using solvents to remove grease

and oil
SP2 (hand tool cleaning) using hand scrapers to
remove dirt, dust, coat
SP3 (power tool cleaning) using power wire brushes,
grinders, sanders to remove llose corrosion products
SP4 (Flame cleaning) removing contaminants by a
flame or high velocity oxyfuel burner
KFUPM-ME 24
472 (062)
1. Surface Preparation
SP5 (white metal blast)
using abrasive blasting
to remove oil, mill scale
and paint. Uses high
pressure air (690 kPa)
with abrasives (Al2O3)
Abrasive blasting can
provide 50-115 m
anchor pattern.
KFUPM-ME 25
472 (062)
KFUPM-ME 26
472 (062)
2. Selection of a Coat System

Factors considered in coating selection:

Service environment
Operating condition (i.e., a coat selected for acid environment
should be resistant to acids)
Temperature, humidity, contaminants (the coat selected should
withstand the range of operating conditions)
Ultra violet (UV) exposure
Metal to be protected (the substrate)
Chemical compatibility
Thermal compatibility
Adhesion
KFUPM-ME 27
472 (062)
2. Selection of a Coat system
Factors considered in coating selection (cont.)
Environmental regulations
Standards
Appearance and Color
Cost
Temperature and humidity at time of application
Application during shutdowns or during operation ?
Availability of maintenance
A paint system includes specification for type,
method of application, and number of layers of
various paints required for a particular job.
KFUPM-ME 28
472 (062)
2. Selection of a Coat system
The coat selection process depends on the performance properties of the
binder. The table below compares the major binders in terms of humidity,
corrosion, UV resistance, and chemical resistance.

See www.sherwin-williams.com for information of over 1000 paint systems for industrial and marine coatings.
KFUPM-ME 29
472 (062)
2. Selection of a Coat system
Example: an ARAMCO
approved paint system by
HEMPEL.
Note:
For atmospheric service
Surface preparation
specification
Primer coat
Intermediate coat
topcoat
KFUPM-ME 30
472 (062)
2. Selection of a Coat system
To decide upon a suitable system for the work
you want to do, follow this sequence:
identify the material to be painted
note which primer is most suitable
note which undercoats and topcoats are suitable for
each primer
decide on your topcoat preference.
select the primer and undercoat which allow that
topcoat.
KFUPM-ME 31
472 (062)
3. Applications
Manual (brushing and rolling)
Easy but difficult to control coating thickness
Spraying
Air spray (air is used to atomized and propel the
coating)
Airless spray (the coating container is pressurized
to atomize the coating in the gun)
 32
Air-Spray Gun

1 5
3
Air Supply 6

4
2

5
1
Spray Gun Air Regulators
2 6

Fluid Hose Air Compressor

3
Air Hose
4
Pressure Pot
KFUPM-ME 33
472 (062)
3. Applications
Wet film thickness (WFT): assuming
that the substrate is flat and no paint
is lost.
1 liter (1000 cm3 or 1x10-3 m3) = area
x WFT
Example: Suppose you want to
cover 1 m2 by 1L:
WFT = 1x10-3 m3/ 1 m2 =
1x10-3 m = 1mm.
Dry film thickness (DFT): volatiles
evaporate and only pigments and
binder will be left in the coat and the
dry film becomes thinner
Example: Suppose that the above
paint consists of 50% volatile and
50% of solids by volume.
DFT = WFT * %solids = 1mm
* 0.5 = 0.5 mm
KFUPM-ME 34
472 (062)
3. Applications
Theoretical Coverage on flat surfaces.
Coverage (m2 ) = liters of coating X %solids X 1000/DFT
(m)
Example: What is the coverage area of one
liter of paint (50% solids) with a DFT of 250
m?
Coverage = 1 X 0.5 X 1000/250 = 2 m2
KFUPM-ME 35
472 (062)
4. Coating Inspection and Testing

Holiday: bare area in the

coated surface where
there is a direct contact
between the
environment and the
coated metal
It is important to locate
small holidays and
recoat
KFUPM-ME 36
472 (062)
Holiday Detection System

Low voltage wet-sponge holiday detector Can detect holidays in non-

conductive coatings less than 20 mil thick (500 m)
The holiday detector is connected to the metal substrate of the test piece using a
wetted sponge that conducts electricity. A low voltage is applied b/w the
detector and the metal.
At holidays, a current will flow between the holiday and the detector. A beep
is sounds.
KFUPM-ME 37
472 (062)
5. Coating Failure
Coating failure can be the result of many factors:
Poor surface preparation
Poor selection
Poor application technique
Unexpected changes in service environment
Aging (weathering effects)

Types of discontinuities in coating failure

Holidays
Pinholes: a hole in the coating penetrating all the way to the substrate
Coating discontinuities usually appear at:
Fabrication defects
joints (welds, nuts, bolts, rivets)
Hard to reach area during applications (corners)
Sharp edges of the structure to be protected
KFUPM-ME 38
472 (062)
5. Coating Failure
Common types of coating failure
Blistering:
appear as surface bubbles which are
filled by water vapor, air, or solvent
vapor.
blisters may be
at coating-substrate interface
between adjacent coating layers
Caused by the penetration of moisture
through the coating into areas of poor
adhesion.
Incorrect selection of primer
KFUPM-ME 39
472 (062)
5. Coating Failure
Cracking:
appear as cracks
caused by different degree in thermal
expansion and contraction between
the coat and the metal.
reduce corrosion protection
Wrinkling:
appear as ridges at the surface of the
coat
usually appear in thick coatings
result from swelling of the surface
Caused by difference in drying
between the surface and the body of
the coat
little effect on corrosion protection
KFUPM-ME 40
472 (062)
5. Coating Failure
Flaking and Peeling
Loss of paint due to loss
of adhesion
Caused by incorrect
surface preparation or
incorrect primer
primer/topcoat
KFUPM-ME 41
472 (062)
Cement Linings
Cement lining (3-10 mm)
provides excellent internal layer
of protection against corrosion in
pipes and tanks.
The cement layer is permeable but
form alkaline solution in contact
with steel which protects steels.
Cement lining is widely used in
cast iron piping systems for
potable water and sewage.
Cement is applied in a pipe
internally as shown in the
figure.
There are different cement
materials for different
applications.
 Inhibitors

Dr. Zuhair M. Gasem

ME Dept, KFUPM
Dhahran, Saudi Arabia

References:
1. Handbook of Corrosion Engineering by
P. R. Roberge
2. Corrosion Control by S.A. Bradford
KFUPM-ME 43
472 (062)
Inhibitors
Inhibitors are chemicals added in small amounts to the electrolyte to reduce
corrosion in closed systems such as in recirculation-cooling systems,
cooling towers, condenser tubes, and boilers.
The decision of using inhibitor involves an economical balance between
the cost of the inhibitor against the cost of corrosion.
Inhibitors are used widely in the oil extraction and production industries
and in cooling systems.
The composition of industrial inhibitors are secrets of their manufacturers.
Inhibitors react and adsorb to the metal surface and form one of the
following films:
A stable metal passive film
A barrier film of adsorbed inhibitor
A thick barrier layer of corrosion products or the inhibitor
KFUPM-ME 44
472 (062)
Inhibitors
Depending on the effect of the
adsorbed films on corrosion reactions,
inhibitors are classified as either:
anodic inhibitor (slow anodic
reactions)
cathodic inhibitor (the presence of
the adsorbed film slow down
cathodic reactions)
general inhibitor (slow both anodic
and cathodic)
Organic inhibitors
KFUPM-ME 45
472 (062)
Cathodic Inhibitors
Cathodic inhibitors can provide inhibition by two
different mechanisms:
cathodic poisoning
slow the kinetics of cathodic reactions
Example: arsenic compounds make the recombination of hydrogen
more difficult
H+ + H+ + 2e- H + H -- H2
slow
cathodic precipitates
Active elements of the inhibitor react with the electrolyte and form
oxides which precipitate on the cathodic areas to increase the
surface impedance and limit the diffusion of reducible cations
Example: Ca, Zn, and Mg salts.
KFUPM-ME
472 (062) Passivating Inhibitors 46

Passivating inhibitor: shift the

corrosion potentials into the
passive region.
The added inhibitor must exceed
a critical concentration to reach
the passive region as shown in
figure 1.
It is essential to monitor the
inhibitor concentration to avoid
acceleration of corrosion.
The example shown in figure 2 is
for a stainless steel in:
15%H2SO4
15%H2SO4 + CuSO4
Note the change in Ecorr
KFUPM-ME 47
472 (062)
Passivating Inhibitors
Examples of passivating inhibitors:
Inhibitor based on oxidizing anions such as chromate (CrO4-), nitrite
(NO2-), and nitrate (NO3-) which can passivate steel even in the absence
of oxygen.
Inhibitors based on non-oxidizing anions such as phosphate (PO43- )
and molybdates (MoO42-) which require oxygen to passivate steel.
Passivating inhibitors are very effective and consequently the
most widely used especially in cooling water systems.
The use of passivating inhibitors are usually limited by
environmental regulations applied to reduce pollution and
carcinogenic effect.
KFUPM-ME 48
472 (062)
Organic Inhibitors
Organic inhibitors form thin protective organic
films on the entire metal surface. The film consists
of molecules that adsorb to the metal surface and
reduce the available surface for corrosive ions
(such as Cl-) to react with the surface.
Example: amines (-NH2) and their salts.
The effectiveness of these inhibitors depends on
the chemical composition, their molecular
structure, their affinities for the metal surface, and
the temperature and pressure in the system. methylamine
KFUPM-ME 49
472 (062)
Scavengers
Scavengers: a chemical added to eliminate
dissolved oxygen from closed system at neutral or
alkaline pH.
Sulfite is used widely in water at ambient
temperature:
Na2SO3 + 1/2O2Na2SO4
Hydrazine (N2H4) is a scavenger used in boilers:
N2H4 + O2 N2 + 2H2O
KFUPM-ME 50
472 (062)
Examples of Inhibitors
Service
environment

Common
inhibitors used
KFUPM-ME 51
472 (062)
Examples of Inhibitors