NEW AND USED CRANES AND EQUIPMENT

Tel: (877) 244-4380 or (510) 638-8100

Web: www.biggecranesales.com

STINGER 3470 | Boom Truck Crane

STINGER 3470
BOOM TRUCK CRANE

FEATURES
34,000 Ib (15 422 kg) maximum lifting Electronic Load Moment Indicator and
capacity anti-two-block device standard

80 (24.38 m) maximum sheave height Externally located planetary rotation

drive for easy accessibility for mainte-
120 (36.57 m) maximum sheave nance
height with 24-40 (7.31-12.19 m) jib
2-speed planetary winch has 10,500 lb
27-70 (82.30-21.34 m) three-section (4 703 kg) maximum permissible 1 part
full power fully synchronized boom line, 37,000 Ib (16 782 kg) breaking
strength, 186 ft/min (57 m/min)
Exclusive color coded boom and load maximum line speed
charts
Dual control station with direct
Easy-to-install optional 24 (7.31 m) mechanically controlled hydraulic
one stage or 24-40 (7.31-12.19 m) system
two stage telescoping jib, man baskets
or work platform increase job capaci- 70 gal (266 L) capacity hydraulic tank
ties
 BOOM TRUCK CRANE

STINGER 3470

BT MODEL
CAUTION Do not use this specification sheet as a load rating chart. The format of data
LOAD RATINGS is not consistent with the machine chart and may be subject to change.

BOOM LENGTH Maximum Load Chart in pounds (lbs) with fully extended outrigger
AREA OF OPERATION
27 FT 34 FT 43 FT 52 FT 61 FT 70 FT DO NOT OPERATE
LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD IN SHADED AREA
OPERATING WITHOUT
RADIUS BOOM RATING BOOM RATING BOOM RATING BOOM RATING BOOM RATING BOOM RATING
OPTIONAL FRONT
(FT) ANGLE (LB) ANGLE (LB) ANGLE (LB) ANGLE (LB) ANGLE (LB) ANGLE (LB) STABILIZER
(DEG) (DEG) (DEG) (DEG) (DEG) (DEG)
5 77 34,000*
10 66 21,100* 71 17,100* 75 16,000* 78 15,700*
15 54 15,100* 62 14,000* 68 12,100* 72 11,100* 75 10,800* 77 9,600*
20 39 11,100* 51 10,100* 61 9,100* 66 8,600* 71 8,200* 73 7,300*
25 17 7,900* 40 7,700* 53 7,100* 61 6,900* 66 6,600* 69 5,900*
30 23 6,500* 44 6,100* 54 5,600* 60 5,300* 64 4,900*
35 33 4,800* 47 4,700* 54 4,600* 60 4,150*
NOTE: STRUCTURAL STRENGTH RATINGS IN
40 CHART ARE INDICATED WIH AN ASTERISK * 16 3,500* 38 4,100* 48 3,900* 55 3,550*
45 27 3,250* 41 3,200* 49 3,050* Deductions from rate
loads for load handling
50 9 2,950* 33 2,800* 44 2,650* devices BT
55 23 2,500* 37 2,350*
60 29 1,900* Overhaul Ball 125 lbs

65 19 1,700* 1 Sheave Load Block 200 lbs

2 Sheave Load Block 230 lbs

STOWED JIB DEDUCTIONS (POUNDS)

450 360 260 230 200 175 Aux Sheave 50 lbs

JIB CAPACITIES FOR ALL BOOM LENGTHS VERIFY OPERATIONAL MODE SETTING ON LMI DISPLAY BEFORE LIFTING WITH JIB
Loaded Boom Angle 35 40 45 50 55 60 65 70 75 80
Retracted 24 ft Jib 700 825 1,000 1,150 1,340 1,600 1,900 2,300 3,100 4,160
Extended 40 ft Jib 520 580 650 730 810 930 1,080 1,400 1,810 2,260

RANGE DIAGRAM (27 - 70 FT BOOM) GENERAL NOTES

1. The operator must read and understand the Owner's Manual before operating this crane.
2. Positioning or operation of crane beyond areas shown on this chart is not intended or approved except where
specified in Owner's Manual.
3. Loaded boom angles at specified boom lengths give only an approximation of the operating radius. The boom angle
before loading should be greater to account for deflections. Do not exceed the operating radius for rated loads.
4. Use rating of next longer boom for boom lengths not shown. Use rating of next greater radius for load radii not shown.
5. Boom must be fully retracted when jib is erected before lowering below minimum angle. Retracted jib has no lifting
CENTERLINE OF ROTATION

SHEAVE HEIGHT - FEET

capacity below a 50 boom angle.

6. Use rating of next lower boom angle for boom angles not shown on jib load rating chart.
7. Lifting off the main boom point while the swing around jib is erected is not intended or approved.
8. Do not lower boom into this area, as hydraulic pressure will not allow raising the boom without retracting boom first.
9. Crane load ratings on outriggers are based on freely suspended loads with the machine leveled and standing on a firm
uniform supporting surface. No attempt shall be made to move a load horizontally on the ground in any direction.
10. Practical working loads depend on supporting surface, wind and other factors affecting stability such as hazardous
surroundings, experience of personnel, and proper handling, must all be taken into account by the operator.
11. The maximum load which may be telescoped is limited by hydraulic pressure, boom angle, and boom lubrication. It is
safe to attempt to telescope any load within the limits of the load rating chart.
INFORMATION
1. Deductions must be made from rated loads for stowed jib, optional attachments, hooks and loadblocks (see deduction
chart). Weights of slings and other load handling devices shall be considered a part of the load.
2. Crane load ratings with outriggers are based on outriggers and stabilizers extended and set with all load removed
from the carrier wheels.
3. Load ratings do not exceed 85% of tipping load.
DEFINITIONS
1. Operating radius is the horizontal distance from the axis of rotation to the center of the vertical hoist line or load hook
with load suspended.
2. Loaded boom angle as shown in the Load Ratings Chart is the included angle between the horizontal and longitudinal
axes of the boom base after lifting rated load at rated radius.
 BOOM TRUCK CRANE

STINGER 3470

RM MODEL
CAUTION Do not use this specification sheet as a load rating chart. The format of data
LOAD RATINGS is not consistent with the machine chart and may be subject to change.

BOOM LENGTH Maximum Load Chart in pounds (lbs) with fully extended outrigger

27 FT 34 FT 43 FT 52 FT 61 FT 70 FT
OPERATING LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD
RADIUS BOOM RATING BOOM RATING BOOM RATING BOOM RATING BOOM RATING BOOM RATING AREA OF OPERATION
(FT) ANGLE (LB) ANGLE (LB) ANGLE (LB) ANGLE (LB) ANGLE (LB) ANGLE (LB) 360 Full Capacity
(DEG) (DEG) (DEG) (DEG) (DEG) (DEG) Area of
Operation
5 77 34,000*
10 66 21,100* 71 17,100* 75 16,000* 78 15,700*
15 54 15,100* 62 14,000* 68 12,100* 72 11,100* 75 10,800* 77 9,600*
20 39 11,100* 51 10,100* 61 9,100* 66 8,600* 71 8,200* 73 7,300*
25 17 7,900* 40 7,700* 53 7,100* 61 6,900* 66 6,600* 69 5,900*
30 23 6,500* 44 6,100* 54 5,600* 60 5,300* 64 4,900*
35 33 4,800* 47 4,700* 54 4,600* 60 4,150*
NOTE: STRUCTURAL STRENGTH RATINGS IN
40 CHART ARE INDICATED WIH AN ASTERISK * 16 3,500* 38 4,100* 48 3,900* 55 3,550*
45 27 3,250* 41 3,200* 49 3,050*
50 9 2,950* 33 2,800* 44 2,650*
Deductions from rate
55 23 2,500* 37 2,350* loads for load handling
devices RM
60 29 1,900*
65 19 1,700* Overhaul Ball 125 lbs

STOWED JIB DEDUCTIONS (POUNDS) 1 Sheave Load Block 200 lbs

450 360 260 230 200 175 2 Sheave Load Block 230 lbs

JIB CAPACITIES FOR ALL BOOM LENGTHS VERIFY OPERATIONAL MODE SETTING ON LMI DISPLAY BEFORE LIFTING WITH JIB
Loaded Boom Angle 35 40 45 50 55 60 65 70 75 80
Retracted 24 ft Jib 700 825 1,000 1,150 1,340 1,600 1,900 2,300 3,100 4,160
Extended 40 ft Jib 520 580 650 730 810 930 1,080 1,400 1,810 2,260

RANGE DIAGRAM (27 - 70 FT BOOM) GENERAL NOTES

1. The operator must read and understand the Owner's Manual before operating this crane.
2. Positioning or operation of crane beyond areas shown on this chart is not intended or approved except where
specified in Owner's Manual.
3. Loaded boom angles at specified boom lengths give only an approximation of the operating radius. The boom angle
before loading should be greater to account for deflections. Do not exceed the operating radius for rated loads.
4. Use rating of next longer boom for boom lengths not shown. Use rating of next greater radius for load radii not shown.
5. Boom must be fully retracted when jib is erected before lowering below minimum angle. Retracted jib has no lifting
CENTERLINE OF ROTATION

capacity below a 50 boom angle.

SHEAVE HEIGHT - FEET

6. Use rating of next lower boom angle for boom angles not shown on jib load rating chart.
7. Lifting off the main boom point while the swing around jib is erected is not intended or approved.
8. Do not lower boom into this area, as hydraulic pressure will not allow raising the boom without retracting boom first.
9. Crane load ratings on outriggers are based on freely suspended loads with the machine leveled and standing on a firm
uniform supporting surface. No attempt shall be made to move a load horizontally on the ground in any direction.
10. Practical working loads depend on supporting surface, wind and other factors affecting stability such as hazardous
surroundings, experience of personnel, and proper handling, must all be taken into account by the operator.
11. The maximum load which may be telescoped is limited by hydraulic pressure, boom angle, and boom lubrication. It is
safe to attempt to telescope any load within the limits of the load rating chart.
INFORMATION
1. Deductions must be made from rated loads for stowed jib, optional attachments, hooks and loadblocks (see deduction
chart). Weights of slings and other load handling devices shall be considered a part of the load.
2. Crane load ratings with outriggers are based on outriggers and stabilizers extended and set with all load removed
from the carrier wheels.
3. Load ratings do not exceed 85% of tipping load.
DEFINITIONS
1. Operating radius is the horizontal distance from the axis of rotation to the center of the vertical hoist line or load hook
with load suspended.
2. Loaded boom angle as shown in the Load Ratings Chart is the included angle between the horizontal and longitudinal
axes of the boom base after lifting rated load at rated radius.
 BOOM TRUCK CRANE

STINGER 3470

BT MODEL
WINCH DATA BLOCK TYPE
1 Part Line 2 Part Line 3 Part Line 4 Part Line Overhaul Ball 6.25 ton (5.7 mt)
1 Sheave Block 17.5 ton (15.9 mt)
AUX. AUX.

OVERHAUL
BLOCK BLOCK CAUTION
BALL ONE ONE TWO
SHEAVE
LOAD
SHEAVE
LOAD
SHEAVE
LOAD Overload and anti-two-block systems must be in good operating
BLOCK BLOCK BLOCK
condition before operating crane. Refer to Owners Manual.
Cable Lift and Lift and Lift and Lift and
Winch Supplied Max Speed Max Speed Max Speed Max Speed Keep at least 3 wraps of loadline on drum at all times.

Standard
9/16 Diam 10,500 lb 21,000 lb 31,500 lb 34,000 lb Use only 9/16 diameter cable with 37,000 lb. breaking strength on
IWRC XXIP 186 fpm 93 fmp 62 fpm 45.5 fpm this machine.
Stationary
Winch 9/16 Diam 6,720 lb 13,440 lb 20,160 lb 26,880 lb
Rotation 186 fpm 93 fpm 56.7 fpm 45.5 fpm
Resistant

2 MOUNTING CONFIGURATIONS

CARRIER PROVIDED BY TEREX INCLUDED OPTIONS

STINGER BT3470 - Behind Cab Mounting Configuration Fuel tank (45 gal)-175 L
Manufacturer Ford F-750 4 x 2 Chassis Power Steering
Standard Engine Caterpillar C-7 7.2 L I-6 Electric Horn
Standard Horsepower 210 hp @ 2,500 rpm Factory A/C
Standard Torque 605 Ib. Ft. @ 1,440 rpm Power Port (Cigar lighter)
Full Tank Capacity 45 gal (170 L) AM/FM Radio w/ Clock
Standard Transmission Spicer ES066-7B Dual West Coast Stainless Rear View Mirrors
Speed Standard Transmission Manual 7-speed Standard Factory Warranty
Max Speed Standard Transmission 74 mph (118.4 km/h)
Max Gradeability 17.7% in 1st CHASSIS RECOMMENDATIONS
Standard Transmission 15.8% in Rev STINGER BT3470 - Behind Cab Mounting Configuration
Optional Transmission Allison Combined Axle Weight Rating 33,000 Ib (14 969 kg)
Speed Optional Transmission Automatic 5-speed Front Axle Weight Rating 12,000 Ib (5 443 kg)
Max Speed Optional Transmission 74 mph (118.4 km/h) Rear Axle Weight Rating 21,000 Ib (9 525 kg)
Max Gradeability 21.1% in 1st Wheel base 242" (6.15 m)
Optional Transmission 30.5% in Rev Cab to Axle 168" (4.27 m)
Gross Vehicle Weight Rating 33,000 Ib (14 969 kg) Afterframe 96" (2.44 m)
Front Axle Weight Rating 12,000 Ib (5 443 kg) Frame Section Modulus 16.98 in 3 (278 cm3)
Rear Axle Weight Rating 21,000 Ib (9 525 kg) RBM per Frame Rail 1,400,000 in/Ib (16 130 kg/m)
Front Tires 22.5" x 8.5" 11R22.5 G Goodyear G159 Frame Height (Unloaded) 40" (7.62 m)
Rear Tires 22.5" x 7.5" 11R22.5 G Goodyear G167A Exhaust Position Horizontal Left Side
Brakes Air, Hydraulic Anti-Lock System
Exhaust Position Horizontal Left Side
 BOOM TRUCK CRANE

STINGER 3470

RM MODEL
WINCH DATA BLOCK TYPE
1 Part Line 2 Part Line 3 Part Line 4 Part Line Overhaul Ball 6.25 ton (5.7 mt)
1 Sheave Block 17.5 ton (15.9 mt)
AUX. AUX.

OVERHAUL
BLOCK BLOCK CAUTION
BALL ONE ONE TWO
SHEAVE
LOAD
SHEAVE
LOAD
SHEAVE
LOAD Overload and anti-two-block systems must be in good operating
BLOCK BLOCK BLOCK
condition before operating crane. Refer to Owners Manual.
Cable Lift and Lift and Lift and Lift and
Winch Supplied Max Speed Max Speed Max Speed Max Speed Keep at least 3 wraps of loadline on drum at all times.

Standard
9/16 Diam 10,500 lb 21,000 lb 31,500 lb 34,000 lb Use only 9/16 diameter cable with 33,600 lb. breaking strength on
IWRC XXIP 186 fpm 93 fmp 62 fpm 45.5 fpm this machine.
Stationary
Winch 9/16 Diam 6,720 lb 13,440 lb 20,160 lb 26,880 lb
Rotation 186 fpm 93 fpm 56.7 fpm 45.5 fpm
Resistant

2 MOUNTING CONFIGURATIONS

CARRIER PROVIDED BY TEREX INCLUDED OPTIONS

STINGER RM3470 Rear Mount Configuration Dual Fuel Tanks (120 gal-454 L)
Manufacturer Sterling LT7501 6 x 4 (60 000) Power Steering
Standard Engine Caterpillar C-7 7.2 L I-6 Electric Horn
Standard Horsepower 300 hp @ 1,440 rpm Factory A/C
Standard Torque 860 Ib. Ft. @ 1,500 rpm Power Port (Cigar lighter)
Full Tank Capacity 120 gal (454 L) AM/FM Radio w/ Clock
Standard Transmission Eaton Fuller RT-8908LL Dual West Coast Stainless Rear View Mirrors
Speed Standard Transmission Manual 10-speed Standard Factory Warranty
Max Speed Standard Transmission 74 mph (120 km/h)
Max Gradeability 54% CHASSIS RECOMMENDATIONS
Standard Transmission STINGER RM3470 Rear Mount Configuration
Optional Transmission Allison Combined Axle Weight Rating 60,000 Ib (27 210 kg)
Speed Optional Transmission Automatic 6 speeds Front Axle Weight Rating 20,000 Ib (9 067 kg)
Max Speed Optional Transmission 74 mph (120 km/h) Rear Axle Weight Rating 40,000 Ib (18 144 kg)
Max Gradeability 17% Wheel Base 261" (6.62 m)
Optional Transmission Cab to Axle 192" (4.87 m)
Gross Vehicle Weight (without crane) 60,000 Ib (27 210 kg) Afterframe 114" (2.89 m)
Front Axle Weight Rating (without crane) 20,000Ib (9 067kg) Frame Section Modulus 30.00 in3 (4.91 cm3)
Rear Axle Weight Rating (without crane) 40,000 Ib (18 144 kg) RBM per Frame Rail 1,800,000 in/Ib (16 130 kg/m)
Front Tires 425/65R 22.5 Michelin XZY (20 ply) Frame Height (Unloaded) 40" (7.62 m)
Rear Tires 11R 22.5 Michelin XDE M/S (14 ply) Exhaust Position Horizontal Left Side
Brakes Air, Hydraulic Anti-Lock System
Exhaust Position Horizontal Left Side
 BOOM TRUCK CRANE

STINGER 3470

BT MODEL
SPECIFICATIONS

BOOM CONTROLS
27-70 (82.30-21.34 m) three-section full power fully synchronized Fully proportional, excellent metering characteristics for precise boom
boom. Patented keel boom design utilizes a keel shaped base plate movements. Independent outrigger controls allow the crane to be
combined with a deep, four plate boom section to optimize strength / stable and level in rigorous working conditions. Load Moment
rigidity-to-height ratio. Exclusive, patented color-coded boom and load Indication System has audio alarm and functional shut down when
charts allow the operator to easily determine boom extension, boom operator encounters an overload situation.
angle and load capacity. Maximum tip height with three-section
27-70 (82.30-21.34 m) boom is 80 (24.38 m). Maximum tip height
with optional two-stage 24-40 (7.31-12.19 m) jib is 120 (36.57 m). OUTRIGGERS
Front outriggers are Link-Type. The maximum width over main
WINCH outrigger pad is 20 5" (6.23 m), main outrigger spread at maximum
ground penetration is 20 (6.10 m).
Hydraulic winch with gear motor and planetary reduction gearing
provides 2-speed operation. First layer rope pull is 11,400 Ib (5 170 Rear outriggers are A-Frame type. The maximum width over auxiliary
kg). Wire rope size is 9/16" (14 mm) with 37,000 Ib (16 782 kg) outrigger pads is 10 2" (3.09 m).
breaking strength.
SUBFRAME
OPERATING SPEEDS Single fabricated, closed-box style subframe yields greater strength
Mainframe / turret assembly planetary gear rotation provides 180 and rigidity. Wheelbase for standard truck crane mounting configura-
rotation (370 with optional front bumper outrigger). Swing rotation is tion is 242" (6.15 m).
55 seconds. Boom up/down is 25/16 seconds and boom
extend/retract is 61/29 seconds.
OPTIONS AND ACCESSORIES
Single and two-stage jibs Self-leveling work platform
HYDRAULICS
Multi-part load blocks Winch drum tensioner
Three-section pump allows the operator to perform simultaneous
Main winch with 2 speed motor Continuous rotation
crane operations (winch, boom and swing). Capacities are 32, 17 and
8 gpm (122, 64 and 30 L/m). Hydraulic tank capacity is 70 gal (265 L). Auxiliary winch Oil cooler
Rotation-resistant load line Single front bumper outrigger
Heavy duty wood flatbeds (required for 370 or continuous
rotation)
Extra heavy duty wood flatbeds Hydraulic hose reel
Extra heavy duty steel flatbeds Hydraulic auxiliary tool circuit
Radio remote controls Tool Box
One-man or two-man baskets
 BOOM TRUCK CRANE

STINGER 3470

RM MODEL
SPECIFICATIONS

BOOM CONTROLS
27-70 (82.30-21.34 m) three-section full power fully synchronized Fully proportional, excellent metering characteristics for precise boom
boom. Patented keel boom design utilizes a keel shaped base plate movements. Independent outrigger controls allow the crane to be
combined with a deep, four plate boom section to optimize strength / stable and level in rigorous working conditions. Load Moment
rigidity-to-height ratio. Exclusive, patented color-coded boom and load Indication System has audio alarm and functional shut down when
charts allow the operator to easily determine boom extension, boom operator encounters an overload situation.
angle and load capacity. Maximum tip height with three-section
27-70 (82.30-21.34 m) boom is 80 (24.38 m). Maximum tip height
with optional two-stage 24-40 (7.31-12.19 m) jib is 120 (36.57 m). OUTRIGGERS
Rear outriggers are Link-Type. The maximum width over main
WINCH outrigger pad is 20 5" (6.23 m), main outrigger spread at maximum
ground penetration is 20 (6.10 m).
Hydraulic winch with gear motor and planetary reduction gearing
provides 2-speed operation. First layer rope pull is 11,400 Ib (5 170 Front outriggers are Out and Down type. The maximum width over
kg). Wire rope size is 9/16" (14 mm) with 33,600 Ib (15 240 kg) auxiliary outrigger pads is 17 6" (5.34 m).
breaking strength.
SUBFRAME
OPERATING SPEEDS Single fabricated, closed-box style subframe yields greater strength
Mainframe / turret assembly planetary gear rotation provides 180 and rigidity. Wheelbase for standard truck crane mounting configura-
rotation (370 with optional front bumper outrigger). Swing rotation is tion is 261" (6.63 m).
55 seconds. Boom up/down is 25/16 seconds and boom
extend/retract is 61/29 seconds.
OPTIONS AND ACCESSORIES
Single and two-stage jibs Self-leveling work platform
HYDRAULICS
Multi-part load blocks Winch drum tensioner
Three-section pump allows the operator to perform simultaneous
Main winch with 2 speed motor Continuous rotation
crane operations (winch, boom and swing). Capacities are 32, 17 and
8 gpm (122, 64 and 30 L/m). Hydraulic tank capacity is 70 gal (265 L). Auxiliary winch Oil cooler
Rotation-resistant load line Single front bumper outrigger
Heavy duty wood flatbeds (required for 370 or continuous
rotation)
Extra heavy duty wood flatbeds Hydraulic hose reel
Extra heavy duty steel flatbeds Hydraulic auxiliary tool circuit
Radio remote controls Tool Box
One-man or two-man baskets