Scribd
Upload
169 views

PWM C

This document describes a Pulse Width Modulation (PWM) program for a PIC microcontroller. It initializes the microcontroller's clock and ports, then sets up PWM output on pin RC3 using Timer 2. The PWM duty cycle is varied from 0 to 255 and back in a loop, and the output pin is also switched between RC3 alone and RC3+RC2 to steer the pulse.

Uploaded by

More Fun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
169 views

PWM C

This document describes a Pulse Width Modulation (PWM) program for a PIC microcontroller. It initializes the microcontroller's clock and ports, then sets up PWM output on pin RC3 using Timer 2. The PWM duty cycle is varied from 0 to 255 and back in a loop, and the output pin is also switched between RC3 alone and RC3+RC2 to steer the pulse.

Uploaded by

More Fun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

// ***************************************************************************

// File Name : pwm.c


// Version : 1.0
// Description : Pulse Width Modulation (PWM)
// Single Output, Steering Mode
// Author(s) : RWB
// Target(s) : PICJazz 16F690 Board
// Compiler : HITECT PICC-Lite Version 9.60PL1
// IDE : Microchip MPLAB IDE v8.00
// Programmer : PICKit2
// Last Updated : 03 Jan 2009
// ***************************************************************************
#include <pic.h>
/* PIC Configuration Bit:
** INTIO - Using Internal RC No Clock
** WDTDIS - Wacthdog Timer Disable
** PWRTEN - Power Up Timer Enable
** MCLREN - Master Clear Enable
** UNPROTECT - Code Un-Protect
** UNPROTECT - Data EEPROM Read Un-Protect
** BORDIS - Borwn Out Detect Disable
** IESODIS - Internal External Switch Over Mode Disable
** FCMDIS - Monitor Clock Fail Safe Disable
*/
__CONFIG(INTIO & WDTDIS & PWRTEN & MCLREN & UNPROTECT \
& UNPROTECT & BORDIS & IESODIS & FCMDIS);
// Using Internal Clock of 8 MHz
#define FOSC 8000000L
// Delay Function
#define _delay_us(x) { unsigned char us; \
us = (x)/(12000000/FOSC)|1; \
while(--us != 0) continue; }
void _delay_ms(unsigned int ms)
{
unsigned char i;
if (ms == 0) return;
do {
i = 4;
do {
_delay_us(164);
} while(--i);
} while(--ms);
}
void main(void)
{
unsigned int ipwm;
unsigned char state;
OSCCON=0x70; // Select 8 MHz internal clock
TRISC = 0x00; // Set All on PORTC as Output
ANSEL = 0x00; // Set PORT AN0 to AN7 digital I/O
ANSELH = 0x00; // Set PORT AN8 to AN11 as Digital I/O
PORTC = 0x00; // Turn Off all PORTC
/* Init PWM for Single Output */
CCP1CON=0b00001100; // Single PWM mode; P1A, P1C active-high; P1B, P1D active-
high
CCPR1L=0; // Start with zero Duty Cycle
T2CON=0b00000101; // Postscale: 1:1, Timer2=On, Prescale = 1:4
PR2=0x65; // Frequency: 4.90 kHz
TMR2=0; // Start with zero Counter
PSTRCON=0b00000100; // Enable Pulse Steering on P1C (RC3)
state=0; // Start with state 1
for(;;) {
ipwm=0;
while (ipwm < 255) {
CCPR1L=++ipwm;
_delay_ms(5); // Delay 5 millisecond
}

ipwm=0xff;
while (ipwm > 0) {
CCPR1L=--ipwm;
_delay_ms(5); // Delay 5 millisecond
}

_delay_ms(100); // Delay 100 millisecond


if (state == 0) {
state=1;
PSTRCON=0b00001000; // Enable Pulse Steering on P1D (RC2)
} else if (state == 1) {
state=2;
PSTRCON=0b00001100; // Enable Pulse Steering on P1C and P1D (RC3 and RC2)
} else {
state=0;
PSTRCON=0b00000100; // Enable Pulse Steering on P1C (RC3)
}
}
}

You might also like