4-H-1021-W

PILOT
EXTENSION
AGRICULTURE

Wiring Around Your Home

4-H Electric Division V

 Wiring Around Your Home
Welcome to Division V of the 4-H Electric Project
Congratulations! You've successfully completed the first four units of the 4-H electric program and are now ready to learn
about even more complex aspects of the world of electricity. In the Division V manual you will build upon those things
you learned in the first four manuals and learn some very useful new skills.

Each category listed below contains background information and activities that will help you learn a major project skill
associated with electricity. The project skills learned in this manual include:

Understanding the need for and purpose of Electrical Codes.

Being able to use the correct technical terms associated with residential electrical wiring.
Understanding how electricity is distributed and controlled throughout your home.
Recognizing the different kinds of circuits that may be found in your home.
Reading and creating wiring diagrams and understanding the associated symbols.
Determining the size of a circuit (ampacity) needed for the appliance(s) you wish to use.
Determining if a circuit is energized by using testing equipment.
Understanding grounding and the reason it is important.
Understanding why/when/where circuits should be GFCI protected.
Knowing about arc-fault interrupters and when they should be used.
Recognizing the different types of wires (conductors) and cables and how they are coded.
Understanding the process of mechanically/electrically connecting two or more wires together.
Understanding how to determine t he different sizes and types of receptacles and switches (including three-way).
Being able to safely replace a receptacle and/or switch.

In Wiring around Your Home you need to:

1. Attend your county's 4-H electric meeting(s).
2. Read this manual.
3. Complete the activities presented in this manual.
4. Complete the record sheet in the back of this booklet and submit it as instructed by county 4-H youth
educator or 4-H electric leader.

Upon completion of Wiring Around Your Home you will exhibit one of the following at your local or county fair:

Display board, poster, equipment wiring board, or written report in one of the following areas:
electrical work that you did around your home or other location and how you accomplished it (preferably with
models, pictures or a small part of your total installation). Be sure to include a wiring diagram of your project with
your exhibit.
analyze the current wiring situation in your home or out buildings and develop a new system that you feel would be
better. Be sure to show diagrams of the old and new systems. Also, explain why the new proposed system is better.
any topic covered in this manual.

Note: Poster and display boards should be 22" tall by 28" wide. Equipment wiring boards differ from display boards in that
they show hands-on wiring techniques (i.e., complete wiring of a light controlled by a three-way switch system).
Equipment wiring boards should be no larger than 3' by 3'. The boards should be designed so that they can be
displayed horizontally.

ACKNOWL EDGM ENTS

Using Electric ity was written by Karen Tormoehlen, Roger T ormoehlen, Bill Vollmer, Purdue University Cooperative Extension Specialist, 4-H and
the Indiana State 4-H Joint Electric Committee composed of Fred Bauman, Rex Princell, Wayne Newhart, Roy Mohr, Dave Millis, Betty Baute,
Valerie Sharp, Brad Henderson, Dan Endris, Jim Rupp, Brandon Stevens, Rob Wilson, Rachel Cruz, Darby OConner, Fred Jakubowicz.

2
What's To Come? Introduction
Whats the first thing you do when you walk into a darkened
Introduction 3 room? Reach for the light switch? You probably do this
The National Electric Code 3 without giving it a second thought unless a bulb has burned
How Electricity Travels Throughout the Home 4 out, a fuse is blown or a circuit breaker has tripped and you are
left in the dark.
Electrical Symbols and Building Plans 4
Activity #1 Identify Electrical Plan Symbols 4
Service Entrance Panel Control starts here! 7
Circuit Breakers and Fuses 7
Activity #2 Draw Your Homes Electrical Plan 8
Activity #3 Diagram Your Service Entrance Panel 8
What are Branch Circuits? 8
Types of Branch Circuits 9
Activity #4 Is Your Permanent Wiring Adequate? 9
Activity #5 Typical Branch Circuits and Their Loads 10
Activity #6 Is the Circuit Overloaded? 11
Is the Circuit Live? 12
Have you ever given thought to what makes it possible to
Activity #7 Is the Circuit Live (and wired properly)? 12 microwave popcorn, listen to your stereo or have light to read
Grounding 13 with? Permanent indoor wiring is responsible for bringing
Ground Fault Circuit Interrupters (GFCI) 14 electricity throughout your home. This manual will explore
Activity #8 Identifying GFCIs in Your Home 14 types of permanent indoor wiring that make our lives
Arc Fault Circuit Interrupters (AFCI) 15 comfortable through the ability to use lights and appliances in
our homes. You will also be given instructions on how to
Wiring Types, Sizes, Insulation, Color Coding 15
make safe and simple repairs to your existing electrical
Connecting Wires with Solderless Connectors 16 system.
Activity #9 Using Wire Nuts/Making Good Connections 16
Types of Electrical Cable 17
Activity #10 Symbols/Markings on Wires/Cables 18 The National Electric Code
Electrical Boxes 19
Receptacles/Plug-in Outlets 19
The National Electrical Code (NEC) was developed by
Activity #11 Identifying Different Receptacles Available 20
the National Fire Prevention Association (NFPA) as a set of
Switches 21 rules to encourage safe practices while working with
Important Safety Guidelines 23 electricity. It states The purpose of this Code is the practical
Putting it Together 24 safeguarding of persons and property from hazards arising
Activity #12 Redesigning Your Bedroom 24 from the use of electricity. The NEC is updated every few
4-H Club Record 25 years. In addition to the NEC, cities, counties, and states may
Poster and Display Board Check Sheet 27 adopt regulations that need to be followed by consumers,
electricians and builders. A permit may be required to be
obtained from a local inspector whenever you make major
Appendices:
changes to, or install something new in, your home-wiring
#1. Replacing an Outlet/Receptacle 28 system.
Replacing an End of the Run Receptacle 28
Replacing a Middle of the Run Receptacle 29 Before attempting any electrical work, contact a local inspector
#2. Replacing Switches 30 to learn more about the electrical code(s) in your area and the
Replacing Single Pole Switches with Terminal Screws 30 rules that you need to follow when making changes to your
Replacing Three-Way Switches 31 electrical system. Your local electrical utility may also have
Installing a Dimmer 33 certain wiring and inspection requirements. Remember to
#3. Electrical Terminology Glossary 34 always turn off the power to any circuit that you may be
working on.

3
This manual does not attempt cover each and every aspect
of the residential wiring rules as set forth in the National
Electric Code (NEC). The NEC is, if fact, a very detailed
and complete set of rules governing the safety and use of
electricity in business, industry and the home. This manual
serves as more of overview of how to make some basic
repairs or improvements to an existing home electrical
system which would be consistent with the rules set forth
in the NEC. The language of the NEC specifies what the
MINIMUM safety standards to be used are.

How Electricity Travels

Throughout the Home
Electricity is supplied to your home through your electric
utilitys overhead or buried power lines.* Before entering
your home, electricity passes through a watt-hour meter
which measures the amount of electricity used. It then
continues into your house through the Service Entrance
Panel (also called a load center), where circuit protection
devices such as circuit-breakers or fuses are located
(Figure 1). Electricity is then distributed throughout your
home using branch circuits to provide power to appliances FIGURE 1 Residential Electrical System
and lights through receptacles, switches, and fixtures.
An outlet is any point in an electrical system where current is
Electricity arrives at your home on two energized taken out of the system in order to supply power to the attached
(hot) conductors and one non-energized (neutral) electrical equipment. An outlet can be one of two basic types: A
conductor. Between the two hot conductors a typical Receptacle outlet or a Lighting outlet. A receptacle outlet is
voltage of 240 Volts AC will be present and between one in which one or more receptacles are installed for the purpose
either of the hot conductors and the neutral or of attaching plug and cord-connected type devices, and a
grounded conductor approximately 120 Volts will be lighting outlet is one intended for a direct-wired connection to a
present (Figure 1). Under the right circumstances, 120 lamp holder, luminaire (lighting fixture) or ceiling fan. Special-
volts can injure or kill you; 240 volts could present an purpose outlets also exist. These may be dedicated to a specific
even greater risk for injury or electrocution. Therefore, type of equipment such as a furnace, wall oven, garbage disposal
it is very important that power be removed from a or another similar piece of equipment.
circuit before any repairs or changes are made to it.
There are a number of testing devices that can check for ACTIVITY #1
the presence of voltage in the circuit and one of these
should be used to make sure that the power is off. These Identify Electrical Plan Symbols
testing devices will be discussed later in this manual. 1. Things needed
pencil
this manual
Electrical Symbols and 2. What you will do:
a. Study the symbols in the table named Electrical
Building Plans Symbols and Outlets. (Figure 2)
b. Examine the Sample Home Electrical Plan and
Electrical symbols are used on home building plans in notice how the symbols are used (Figure 3).
order to show the location, control point(s), and type of c. Answer the questions that are found below the
electrical device(s) required at those locations. These
symbols, which are drawn on top of the floor plan, show electrical plan (Figure 3).
lighting outlets, receptacle outlets, special purpose d. Check your answers on the last page of the Glossary
outlets, fan outlets and switches. Dashed lines are drawn (Appendix 3) in this manual.
between the symbols to denote which switch(es) control
specific light(s) or receptacle(s). There are quite a few * To refresh yourself on how electricity gets from the power
symbols used to represent the devices used in home generating facility to your home refer to the Division III
wiring but some of them are very similar, so care should Electric manual.
be used when working with them.

4
FIGURE 2 Symbols and Outlets

5
6
1. Why do two switches connect to the paddle fan? 5. Which five areas use GFCI-protected receptacles?
ACTIVITY 1 (FIGURE 3) Sample Home Electrical Plan

Slow/Fast Speeds One for Light/One for Fan

2. How many lights are connected to 3-way switches? 6. Which room makes use of Split-Circuit receptacles?
1 4 5

3. Where are multiple lights controlled by one switch? 7. Where is the Service Entrance Panel located?

Garage Exterior Bath Bedroom 2

4. What two appliances are shown using 240 Volts? 8. What does WP stand for on an outdoor receptacle?

NOTE: Answers on last page of Glossary.

 Service Entrance Panel (S.E.P.) When choosing circuit protection devices for a service
entrance panel, it is important to match the rating of the
The electrical panel, breaker box, fuse box, load center, or circuit breaker or fuse to the circuit that it will be protecting.
service entrance panel (it is known by many names) (Figure In other words, you would want to use a 15-amp rated
4) has the job of distributing power throughout your home. It breaker on a 15-amp lighting branch circuit; you would not
provides the primary means for a homeowner to disconnect want to use a 20-amp rated breaker. Neither would you want
the power that comes from the feed provided by your electric to use a 15-amp rated circuit breaker on a 20-amp small-
utility company. It also provides circuit protection for the appliance branch circuit. The same principle would apply if
various branch circuits that make up a residential electrical fuses were being used for circuit overload protection. Also,
wiring system. when selecting breakers, it is important to match the service
entrance panel you have with compatible-style breakers.
Power comes from the feeder lines into the Main Breaker
(usually the topmost breaker in the panel) which is usually To be able to properly diagnose an inoperative branch
rated at 100 or 200 amps. From there, individual breakers circuit, it is important that you learn how to recognize when
then distribute power and provide overload protection for a circuit breaker has tripped or when a fuse has blown. The
each of the individual circuits (branch circuits) that run first clue that this has happened would be that none of the
throughout your home. lights or devices plugged into receptacles that are a part of
the circuit would be functioning.

When a fuse has blown, it is usually quite apparent by

viewing the fusible metal link inside the fuse housing
through the transparent window in the front. If the metal link
has a gap in it, the fuse has blown (Figure 5 - the link has
melted due to the excessive current flow). Another possible
indicator is blackening of the transparent window as a result
of the melting and vaporizing of the metal link. In this case,
it could be difficult to actually inspect the metal link. If it is
not visually possible to tell if a fuse is blown, you can
always remove it from the panel and test it using a testing
device such as an Ohm-meter or continuity tester.
Its a good idea to identify
each circuit on the inside
of the SEPs front cover.

FIGURE 4 Service Entrance Panel

Gap
These branch breakers have ratings ranging from 15 to 100
amps. Lighting circuits are typically 15 amps, receptacle
circuits 20 amps, and a sub-panel circuit supplying power to a Fuse with Link Intact Fuse with Link Blown
garage or tool shed would usually be 60 or 100 amps.
Dedicated high-power branch circuits such as those for an air
conditioner, furnace, electric range, or electric water heater
may use breakers running from 30-60 amps. The main breaker WLV to take photo
is in series with the branch circuit breakers. Therefore, turning
off power to the main breaker prevents power from being
supplied to all of the branch-circuit breakers.

Older homes, whose electrical wiring has not been upgraded,

may still be using fuses for circuit protection, however, these Tripped Circuit Breaker
are becoming less common. It is still useful to know about
fuses because even items like your automobile make use of FIGURE 5 Blown Fuses/Tripped Breakers
them to protect its electrical system.
When a toggle-type breaker has tripped, the ON/OFF
toggle lever either reverts back to its OFF position or it sits
Circuit Breakers and Fuses somewhere (floats) between the ON and OFF positions.
To reset the breaker, move it fully to the OFF position and
Circuit breakers and fuses are designed to stop the flow of
then back to the ON position.
current in a circuit if it becomes overloaded. The amount of
time required for a breaker to trip (open the circuit) or fuse
to blow depends on the amount of overload current. A circuit Older Push Button type circuit breakers usually have a
breaker trips immediately when a short circuit occurs, but small window on the front with the words ON and OFF.
delays an appropriate amount of time before tripping in the For a normally-functioning circuit, the breaker will display
event of an overload. ON in the window.
7
If an overload occurs and the breaker is tripped, it will 3. Check
display OFF. Pushing the button will reset the breaker and, a. Ask your mom, dad, or 4-H electric leader to
if the electrical fault that caused it to trip is no longer present, review your wiring diagram with you. Did they
ON should then appear in the window. suggest any corrections or additions? If yes,
what were the suggested changes?
Blown fuses will need to be replaced and tripped circuit
breakers reset, but dont do this before investigating the ____________________________________
possible causes for the overload or short-circuit. There simply ____________________________________
may have been too many items plugged into the branch- ____________________________________
circuit receptacles and turned on at the same time, causing an ____________________________________
overload or, there may be a short in the plug or cord of a ____________________________________
cord-connected device.
____________________________________
Your service entrance panel may also be
equipped with one or more Ground-Fault
Circuit Interrupters (GFCIs). GFCIs
function as a normal breaker but have the ACTIVITY #3
added capability of opening the circuit if Diagram Your Service Entrance Panel
even a small amount of current leaves the
circuit and begins to flow on another path,
such as through your body. This helps to This activity will help you become better acquainted with
protect you from injury or electrocution your Service Entrance Panel.
due to electrical shock.
1. Things needed:
You can recognize a GFCI by the test Pencil, ruler, paper, this manual.
button on the front which, when pressed, 2. What you will do:
trips the breaker and causes the circuit a. Create a diagram of your service entrance panel
to open. When the breaker is tripped, by making a pictorial drawing of the panel that
either by using the test button or due to an shows the location and ratings (amperes) of the
actual ground fault, a colored flag
installed circuit breakers and/or fuses.
appears behind a clear window letting you
the breaker has tripped.* Resetting the
b. If there is a number embossed on the panel next
breaker is done by switching the toggle handle FIGURE 6 to the breaker or any existing labeling that tells
to the off position and then back to the on GFCI Breaker which branch circuit it controls, record this
position. GFCI receptacles and their use will with Tripped information on your diagram as well.
be discussed later in this manual. Indicator c. Record the unused spaces that can be used for
future system expansion. Unused spaces will
*Note: Not all GFCIs have visual "tripped" indicat or window s. either be stamped rectangles still attached to the
panel, or there will be filler plugs that have
ACTIVITY #2 been inserted into the panel where a breaker
would normally reside.
Draw Your Homes Electrical Plan d. If your S.E.P. uses breakers, note on your
drawing how many breakers are used on 120-
1. Things needed:
Volt circuits and how many are on 240-Volt
pencil, ruler, paper, this manual
2. What you will do: circuits? (F.Y.I. 240-Volt breakers are usually
a. Diagram the floor plan for the main floor of your thicker than 120-Volt ones) Did you find any
home. (Refer to Activity 1.) GFCI breakers? Note this information on your
b. With the help of an adult, locate the service entrance pictorial drawing as well.
panel (Figure 4). If it is located on the main floor,
draw its location on your floor plan and label it
"S.E.P." If it is not on the main floor, add some text
on your floor plan that informs the reader of its
What Are Branch Circuits?
Branch circuits are made up of the wires that deliver
location.
c. Next, locate every switch, receptacle (accessible ones electricity throughout your home. The NEC defines a
only), lighting fixture, and fan fixture on the main branch circuit as: the circuit conductors between the final
floor of your home. overcurrent device protecting the circuit and the outlet(s).
d. Refer to the Table of Electrical Symbols and A branch circuit enables appliances and lights to be
Outlets (Figure 3) and place those symbols that operated as needed. A branch circuit should be able to
correspond to the items mentioned in step c. on your handle the combined power demand for all of the attached
floor plan in the approximate location they are found devices without overloading the wires. Therefore, the size
in the rooms. Draw dashed lines from switches to the of the wires used as well as the location and the number of
lighting fixtures, split-circuit receptacles (those receptacles and switches is crucial for safety as well as
controlled by a switch) or the fans they control. convenience.
8
Types of Branch Circuits ACTIVITY #4
Is Your Permanent Wiring Adequate
The kind of circuit installed will depend on how it will
be used by the consumer and the amount of electricity that
for Your Needs?
will be required to be provided by the circuit. In general,
there are three types of branch circuits: 1. Things needed
pencil
1. General purpose branch circuit. Circuits that this manual
provide electricity to the lighting and receptacle
outlets throughout your home. In general, these 2. What you will do:
circuits are 20 amp, 120 volts and use 12 AWG* size a. With the help of an adult, use the following
wires or they are 15 amp, 120 volts and use 12-14 checklist to identify symptoms of wiring
AWG wires. problems in your home. C heck all that apply.

NOTE: Any of the following is a potentially dangerous

2. Small appliance branch circuit. Circuits that
situation and should be corrected by a qualified
provide electricity to receptacles in the kitchen,
professional as soon as possible.
dining, and laundry or similar areas where portable
appliances are often used. In general, these circuits
are 20 amps, 120 volts, and use 12 AWG or larger _____ burning odors
wire. (The NEC requires that a minimum of two
small-appliance branch circuits be provided for the _____ flickering lights, dimming lights, or lights getting
receptacle outlets that serve countertop areas in brighter when appliances are turned on
kitchens.) _____ appliances operating slowly or not as well as they should

3. Individual (Dedicated) branch circuit. Circuits that _____ fuses blowing or circuit breakers tripping frequently
provide electricity to a single receptacle or are hard-
wired directly to a heavy duty appliance such as a _____ too few outlets and switches installed where you need
stove, dryer, water heater, central air conditioner, them (i.e. multiple outlet strips in use)
heat pump or motor above 1/3 horsepower. In _____ multiple octopus connections used for several appliances
general, these circuits are 15 to 100 amps depending at once
on the electrical load of the equipment. The voltage _____ extension cords strung around room in order to connect
used for most dedicated heavy-duty appliance lamps or appliances
circuits is typically 240 volts. _____ overheating of motors

It is critical that the electrical demand placed on a branch _____ getting shocked
circuit not be in excess of what that circuit has been
designed to handle. Not only can repeatedly drawing excess b. If you have checked any of the symptoms of wiring
current damage the wiring and the circuit devices through problems above, identify possible solutions to this
overheating, it can also damage appliances if the supplied situation in your home (i.e., don't use microwave
voltage becomes lower due to the higher current draw. and toaster at same time).

3. Check
a. As k your mom, dad or 4-H electric leader to
review your checklist and adaptations with you.
Did they suggest any changes?

If yes, what were the suggested changes?

FIGURE 7 Inadequate Wiring

* See page 15 for an explanation of conductor sizes: "AWG
stands for American Wire Gage. The lower the number, the
greater the current the wire can handle.

9
ACTIVITY #5
Typical Branch Circuits and Their Loads

This activity will help you become better acquainted with the branch circuits that serve your home and the types of appliances
that might get connected to those branch circuits.

1. Things needed:
Pencil
This manual

2. What you will do:

a. Complete the Example Residential Branch Circuits and Loads diagram by choosing the proper
item from the list of items that appear in the brown curve-shaped area below.
b. Write the item you chose in the correct yellow box.
c. You can check six of the seven items (those that have their wattages listed) for correct placement
by making sure the total of wattage for the three items on a given circuit is equal to the total
wattage shown in the rightmost column.
d. Write the three remaining items in the last three yellow boxes.

FIGURE 8 Example Branch Circuits and Loads

10
ACTIVITY#6
Is the Circuit Overloaded? Maximum Continuous Duty Load Formula
(This formula does not apply to motor circuits)
1. Things needed Amps x Volts = Watts
pencil Watts x 0.8 = Maximum continuous duty load capacity
paper of the circuit.
diagrams from activities #1 and #3 in this manual
The NEC defines "Continuous Load" as" a load where the maximum
current is expected to continue for 3 hours or more."
2. What you will do:
a. Choose a circuit in your home (preferably one
that would be contained within the electrical plan Example: 20 amp (circuit rating) x 120 volts = 2400 watts
you drew earlier in Activity #1). Ask a parent to 2400 watts x 0.8 = 1920 watts
help you determine which receptacles and lights Maximum continuous duty load = 1920 Watts
are a part of that circuit. In the space provided
below, prepare a chart of the electrical loads that Breaker/ Area Voltage Items Used Watts
are typically placed on that particular circuit. See Fuse Size Served
the Example Electrical Loads chart (Figure 9) (Amps)
for assistance in preparing your chart. Living
20A 120 Television 350
Room

Note: If watts are not listed on the appliance, multiply the voltage and amps
listed on the appliance to determine the number of watts used. EXAMPLE 3 Lamps
Space
260

(i.e., 120 volts x 0.4 amps = 48watts).

(T his formula does not apply to motor circuits). CHART
In this example, the maximum
Heater
1400

Breaker/ Area(s) Voltage Items Used Watts continuous load is being exceeded by Boom Box 10
450 watts. Therefore, some of the load
Fuse Size Served* should be distributed to another nearby Computer
(Amps) circuit. 350
& Monitor
Another circuit could be run to the
living room if there is space for an Total 2370
additional breaker to be installed in the
Service Entrance Panel. Maximum
Load (80% )
1920

FIGURE 9 Example Load Calculation

*Dont forget, it is possible that
adjacent rooms could share the
same circuit for some of each 3 . Check
rooms receptacles and/or lights! a. Did the load used on the circuit exceed the
maximum load capacity for the circuit? If yes, how
Total might you redistribute the load to other circuits?

Maximum
Load

b. List the appliances and lights generally used on the

circuit. Locate the number of watts used by each
lighting device or appliance.
c. Add up the total number of watts for the circuit. b. Ask your mom, dad or 4-H leader to review your
d. Use the following Maximum Load formula to chart with you. Did they suggest any changes? If yes,
determine the maximum Continuous load that what were the suggested changes?
the circuit can handle:

NOTE: If a circuit is subject to exceeding the Maximum

Continuous Duty Load, consider shifting one or two of
the receptacles on that circuit to another nearby circuit
that has additional load carrying capacity available.
This will serve to redistribute the load.

11
Is the Circuit Live?
One of the best devices you can use to determine if a circuit
is energized (also called "hot" or "live") is what is known as
an "outlet tester" or "circuit-polarity checker."

By inserting an outlet tester into a 120V receptacle, not only

can you determine if power is available at the receptacle, but
you can also determine if the wiring which runs between the
receptacle and the Service Entrance Panel is connected
correctly. Any incorrectly wired receptacles can cause injury
from electrical shock and, under the right circumstances,
could cause an electrical fire.

As you may recall from the Division III electric project,

power is delivered to receptacles on the "Hot" and "Neutral" FIGURE 10 Example Legend for Outlet Tester
conductors. A third conductor, the Equipment Grounding
Conductor or "Safety Ground", is also included as a part of
the circuit but does not carry any current unless there is an ACTIVITY#7
electrical fault of some kind.
Is the Circuit Live (and wired properly)?
When the circuit conductors are properly connected to a
receptacle, the hot wire will be connected to the electrical 1. Things needed
contact behind the shorter rectangular slot in the receptacle pencil
body. The neutral wire will be connected to the electrical paper
contact behind the longer rectangular slot, and the grounding polarity checker/outlet tester
wire to the electrical contact behind the half-round opening.
2. What you will do:
a. Using a polarity checker, check all of the 120-volt
MEMORY AID: "Hot" is the shorter word, hence
receptacles (easily accessible ones only!) in your
goes to the shorter slot. "Neutral" is the longer word,
home for power and proper wiring. Make sure to
hence goes to the longer slot. "Ground" sounds like
use the legend specific to your checker. Do not use
"round", and hence, goes to the half-round opening. the one shown in the figure above!

b. In the table that follows, record any receptacles that

Figure 9 shows a typical outlet tester. Every tester of this are not working or are wired incorrectly. Note the
style will have a series of lights that illuminate in a specific room's name, the location of the receptacle within
pattern based how the hot, neutral, and ground conductors the room and what was indicated by the polarity
are connected to the terminals of the receptacle. On the unit checker. The first row of the table gives an example
depicted here, the lights are on the end while the top and of what to do. If you find more than five problem
bottom are marked with a legend indicating the meaning of receptacles, you can continue the table on a separate
the light combinations. piece of paper.

c. You may have a few receptacles in your home

controlled by switches (split-circuit receptacles).
These are mostly likely to be found in bedrooms or
living rooms but could be in any room. These will
test as "not working" if the switch that controls
them is turned off.
FIGURE 9 Outlet Tester
To identify if a receptacle is connected to a split
There is only one correct combination of lights for a circuit, test both halves of the receptacle with all
the wall switches in the room turned off. One-half
correctly wired receptacle. Figure 10 shows the legend that
of the receptacle should have power while the
appears on the top of the tester. Be aware that there are two other half should not. If turning the wall switch(es)
ways receptacles may have been installed into your walls... back on provides power to the unpowered half, it is
with the grounding connector facing up or with it facing on a split-circuit. Remember, more than one
down. The legends printed on the top and bottom of the receptacle on a split-circuit may be controlled by
device will be different, but when plugged in and viewed the same switch.
from above the receptacle being tested, it will read correctly.

12
 Circuit Condition
Room Name Outlet Location Action Taken or Proposed
(tester results)

Living Room Left side of N.W. wall - Hot/Neutral Turn off breaker, remove receptacle from wall, inspect
(example) floor lamp is using Reversed and swap wires if needed, power on breaker and re-test.

d. Re-examine your main-floor electrical plan that

you created in activity #2. If you were not able
Grounding
to determine earlier which receptacles, if any,
were wired into split-circuits, go ahead and mark "Grounding" (verb) refers to connecting, to the earth, the metal
them as such on your diagram now. If you need parts of the electrical equipment and devices (distribution panel,
an example, look at Bedroom 1 on the electrical electric box, receptacle, switch, etc.) that make up the electrical
plan used in Activity #1. Notice, it shows five system. The bare copper or green-insulated wires that connect the
split-circuit receptacles controlled by one switch. electrical system to the earth are called grounding (adj.) wires.
These wires do not normally carry circuit current. However, they
4. Check do carry current when they are directing abnormal electrical flow,
a. Ask your mom, dad or 4-H electric leader to such as that caused by a short circuit or lightning strike, into the
review your findings with you. Discuss with them earth to help prevent personal injury or property damage.
the possible process you would use to troubleshoot
why the receptacles are not working as they should The "grounding wire" (sometimes called bonding wire) should be
be. Will you, or someone in your family be able to connected to all metallic boxes of receptacles and light switches
make repairs, or will an electrician be needed? as well as to the green screw of receptacles. Grounding wires
must connect to metallic boxes by using a bonding clip or green-
colored machine screw.
Other devices that could be used to test to determine if power is
being supplied to a receptacle would be: 1) A Digital
The white-insulated electric wires that carry normal circuit
Multimeter that measures and displays the actual AC voltage
current are called "grounded wires" (also known as the neutral
present at the receptacle, 2) a Non-Contact Voltage Tester, or 3)
wires). Grounded wires are connected to the earth by the
a Neon Light Type Voltage Tester. These will not be discussed
grounding wires. This normally occurs at only one point in a
any further in this manual but you may wish to investigate these
residential electrical system - inside the service entrance panel.
devices on your own to learn about their capabilities. For your
reference, examples of these items are shown in Figure 11.
For any electrical system to function safely and properly, a high-
quality earth ground is needed (Figure 12). Metal rods embedded
in a buildings concrete foundation would be the first choice for
an effective electrical ground. This would be followed by well
casings or buried metallic water pipes. If such items are not
available, a ground rod needs to be used. Often, a ground rod is
used to supplement other methods of grounding. A typical
ground rod is a copper-plated steel rod about 5/8" in diameter and
8-10 feet in length. It is driven almost fully into the ground near
the service entrance panel. A grounding wire is run from the
FIGURE 11 Electrical Testing Equipment S.E.P. ground terminal and connected securely to the ground rod.

13
 Groundi ng Wi re
from Tra nsformer
Concrete-Enca s ed
Bui lding Steel El ectrode

Ground Rod Meta l l i c

Wa ter Pi pe

Figure 12 Electrical System Grounding Methods

NOTE: An improperly grounded receptacle may present a
safety issue to you and your family members. If any of the
receptacles you tested in the last activity indicated any type Figure 13 Typical GFCI Wall Receptacle
of fault (including open ground or hot/ground reversed),
let your parents know as this may present a safety issue to
you and your family members. ACTIVITY#8
TIP: A good safety practice when doing electrical wiring is to Identifying GFCIs in Your Home
connect the grounded (neutral) and grounding wires first when
assembling the wiring and to disconnect these wires last when 1. Things needed
disassembling the wiring. pencil
this manual
Ground Fault Circuit outlet tester
Interrupters (GFCI) 2. What you will do
a. Locate and identify* the GFCIs in your home
A Ground Fault Circuit Interrupter (GFCI) (Figure 13) is an
and record their location in the space provided
electronic device used to protect persons against faulty
appliances. GFCI circuitry detects the abnormal flow of below. (HINT: Pay particular attention to the
electricity (current leaving the circuit and flowing on an receptacles in your bathroom, kitchen, garage,
unintended path). It opens the circuit to prevent electricity from receptacles on the outside of your home, and the
reaching the user where it could cause serious injury or death. plugs of hand held electrical devices such as hair
GFCIs are a designed to trip within 15-30 milliseconds (0.015 - dryers.)
0.030 second), whenever a 4-6 milliamp difference in current
flow exists between the hot and neutral wires.

These devices are available as portable units and also are built
into receptacles and circuit breakers. GFCI breakers were
discussed briefly earlier in this manual. GFCIs are required by
Code in certain locations in a home (usually wet/damp spaces)
such as bathrooms, garages, kitchens, basements, around
swimming pools and for all outdoor receptacles. In addition, b. *Use the "TEST" button on any GFCIs receptacles
some hand-held appliances, especially hair dryers, are being you find to see if they are working correctly and
equipped with GFCI protection built right into the plug. help determine if they are protecting any other
receptacles on the circuit. After pressing the test
GFCI circuit breakers have the advantage of providing button, take the outlet tester and check the GFCI
protection for every receptacle on that circuit, but keep in mind receptacle for power. If the power is off, plug the
that when a GFCI breaker trips, power is removed from every tester into other nearby wall receptacles to see if
receptacle and lighting fixture on that circuit. they are being protected by this GFCI. If you find
others off, "RESET" the GFCI receptacle and
GFCI-protected wall receptacles can function in one of two check those other receptacles again. If power was
ways: 1) They can offer protection for just the one receptacle restored, congratulations... you have found those
into which the GFCI is built, or 2) Other receptacles can be other receptacles that also offer you GFCI
supplied with power through the protected one and these protection.
receptacles would then offer GFCI protection as well.
14
 3. Check Copper wire is most often used to wire homes since it is a good
a. Ask your mom, dad, or another adult to verify conductor of electricity. Some older homes have been wired with
your results with you. Did they know of any aluminum wire. (Note: Aluminum wire is no longer approved for
GFCIs that you didnt find? If yes, where were general purpose circuits. Aluminum tends to oxidize over time
they located? and can create poor electrical connections with those items to
which it connects. Also, Aluminum connections tend to become
loose over time which can cause the possibility of arcing to
occur.) Service Entrance Conductors, however, are usually
Aluminum because Copper conductors that size are very
expensive.

When choosing devices, receptacles, switches, or wire

b. Were there any locations in your home that connectors, make sure you choose ones that are made to be
you didn't find a GFCI protected receptacle used with the type of wire you are working with.
where there should have been one?
Copper wire should be used for devices with no
markings or those marked CU-AL or CO-ALR.
Copper-clad aluminum wire (CO-ALR) can be used
with devices marked CO-ALR.
Aluminum wire can only be used with devices marked
CO-ALR.

Arc Fault Circuit Types of Wire Insulation

There are four basic types of wire covering (insulation):
Interrupters (AFCI) 1. Type T - Thermoplastic coated wire. Most commonly
used in homes in dry locations.
An Arc Fault Circuit Interrupter serves a much different
2. Type TW - Thermoplastic coated, moisture resistant
purpose than that of a GFCI. It is designed to sense and
respond to an electrical arcing fault within a wiring system. wire. Used in basements and for outdoor wiring.
Arcing can cause intense heat of up to 10,000F and the 3. Type THW - Thermoplastic coated, heat resistant, and
molten metal coming from the arc can ignite surrounding moisture resistant wire. May be used in both wet and
flammable materials. A major cause of house fires is from dry locations.
arcing caused by wires with loose connections. 4. Type THHN - Thermoplastic coated, heat resistant.
Used in dry locations.
Unless your home was built fairly recently, it may not make
use of AFCI's. Some Electrical Codes may now require them Wire Covering Color Codes
for new construction. Just like GFCIs, AFCIs are available for
use in breaker panels, come built into wall receptacles, and are Wires are covered with plastic insulation to provide both
available as a portable device that can be plugged into by a protection and a method of identification. The insulation color
cord and plug-connected appliance or power tool. normally used for hot wires is either black, red, or blue.
Grounded wire insulation is white or natural gray. Grounding
wire insulation is green, green/yellow, or bare copper (not
Wiring insulated). These colors help to prevent errors when doing
electrical installations or making repairs.
There are a wide variety of wires available for installation in a
home's permanent wiring system. The wire needed for wiring
projects have been specifically identified by the NEC. Wire Sizes and Use
Choosing the correct wire for the job is essential, since using Wires come in a variety of sizes designed for specific jobs and
the wrong wire could result in overheating which could amp loads (Figure 14). It is available in either solid or stranded
damage the wire's insulation or cause a fire. (for increased flexibility) conductor types. Conductor sizes are
numbered using the American Wire Gauge (AWG) rating
Types of Wire system. Smaller numbered wires are larger in size and are more
Wires (conductors) are the means by which electricity travels capable of carrying larger loads of electricity (amps). 14 AWG
from the source of power to the place of use. A residential wire is used for general purpose/lighting branch circuits. 12
wiring system is usually made up of copper, aluminum or a AWG wire is used for small-appliance branch circuits. 6-10
combination of both. The amount of current wires can carry AWG wire is used for higher power appliances such as clothes
is measured in amperes (amps). The larger the wire diameter, dryers, ranges, furnaces and central air-conditioners. Conductors
the more amperes it can carry without it overheating. 2 AWG and larger are normally reserved for use by the main
service entrance conductors or to feed a sub-panel.
15
 Twist-on connectors come in a variety
of sizes and are color-coded based on
the number and sizes of wires that
they are able to handle. While there
are several sizes available, there are
just three sizes that are usually
encountered when working with
residential electrical wiring. The sizes
used most often with home wiring are
orange, red and yellow. Figure 16 Wire
Nuts
As you can see in Figure 16, the red connector can handle the
Wire Size
AWG
14 12 10 8 6 4 2 AWG or larger largest size and/or number of wires while orange can handle the
smallest size and/or number of wires. Most often, you will be
Breaker 15 20 30 40 50 70 100 connecting wires of the same AWG together, but this may not
Rating-Amps
always be the case. The technical specifications provided by the
Figure 14 Wire Sizes and Protection Device Ratings manufacturer will tell you about all the various combinations of
wire sizes and quantities that can be used for any given size nut.

Connecting Wires With Solderless Connectors ACTIVITY#9

Solder should not be used to make home wiring connections! Using Wire Nuts/Making Good Connections
When you need to connect two or more wires together, a
solderless connector should be used. In most lighting and 1. Things needed
general-purpose circuits, U.L. (Underwriter's Laboratory) pencil
approved twist-on "wire-nut"* connectors are used. This this manual
plastic insulator contains a tapered threaded metallic interior several pieces of 14 AWG Solid Insulated Wire
that simply screws tightly over the bare ends of the wires, several pieces of 10 AWG Solid Insulated Wire
connecting them safely and securely (Figure 15). red, yellow and orange wire nuts
linesman pliers
*"Wire-Nut" is actually a registered trademark for this type of
twist-on connector made by Ideal Industries. 2. What you will do
a. Connect different combinations of wires together
To connect the wires together, a short length of insulation must (both sizes and quantities) using the different sized
be removed from the end of each of the wires to be connected. wire nuts. Try connecting both same size wires and
Remove just enough insulation so that no bare wire is exposed different size wires. Try connecting both two
when the nut is screwed on all the way. Begin by twisting the conductors and three conductors together.
wires together, slide the nut over them, and then screw it on
tightly (Figure 15). This makes a solid connection and prevents b. In the table below, record the wiring configuration
any voltage drop from occurring or a potential fire being you used (see example in first row) and list your
caused due to a loose connection. When the nut is properly observations (i.e., loose connection, wires too big,
installed, no bare wire should be visible. If there is bare wire bare wire showing, nut pulls off of wires easily,
showing, remove the nut, and clip off the ends of the wire to etc.) for each of the combinations you try:
shorten them and then replace the nut as before.

Wiring Configuration Your Observations

Example: Yellow Nut
Fits OK/wires are secure
1-10AWG + 2-14AWG
a.

b.

c.

d.
Figure 15 Connecting Wires
e.
Note: Twisting solid conductor wires together is best done
using Linesman Pliers. These have wide, flat jaws that can f.
grip several wires at the same time while twisting.
16
 3. Check Types of Electrical Cable
a. Based on your observations, what size wire nut
should be used when connecting two 14 AWG For most home wiring systems, a cable consisting of two or
conductors? (If not in your table, try it now.) more insulated conductors, surrounded by an outer moisture-
resistant, flame-retardant, nonmetallic insulating jacket, are
used to supply electricity to the various branch circuits. Cable
comes in a variety of standard sizes designed for specific uses.
The conductor size, outer covering, and the type and number of
wires determine how and where a cable can be used.

This type of cable is referred to as Nonmetallic-Sheathed Cable

Does your observation agree with the wire-capacity
(NM). A term still commonly used to refer to this type of cable
chart on the back of the package of wire nuts?
is "Romex." This name served as the trademark for this type of
cable originally manufactured by the Rome Wire and Cable
Company. This name is still commonly used today to refer to
NM-type cable.

There are three basic types of cable for residential use:

If no, what size wire nut does the chart suggested 1) Nonmetallic Sheathed Cable. (NM, NM-B, NMC-B)
for use with two 14 AWG sized conductors? 2) Underground (Feeder) Cable (UF-B) - specifically designed
for direct burial in the ground without any additional
protection required.

3) Service Entrance Cable (SE, USE) - generally used as a

service entrance conductor.

Cable is available with either two or three current-carrying

conductors. Figures 17 and 18 show two and three-wire cable.
b. Based on your observations, what size wire nut
In cables, conductors range in size from 14 AWG through 2
should be used when connecting two 10 AWG
AWG for copper conductors. Two-wire cable contains one
conductors? (If not in your table, try it now.)
conductor with black insulation, another with white insulation,
and a bare equipment grounding conductor (also called the
"ground wire"). Three-wire cable contains one conductor with
black insulation, one with white insulation, a third with red
insulation, and also a bare equipment grounding conductor.
Equipment grounding conductors are permitted to have green
insulation, but bare is the most common.
Does your observation agree with the wire-capacity
chart on the back of the package of wire nuts? All cable must be marked with the following information:

Manufacturer
Type of wire
Wire size
Maximum Working Voltage
Number of Current Carrying Conductors
If no, what size nut is suggested for use with two To make installations easier and to help inspectors make sure
10 AWG sized conductors? that your wiring installation meets code requirements, the outer
sheath of nonmetallic-sheathed cables are color-coded in order
to indicated the wire size (AWG) being used. One part of the
next activity will help you learn which color sheathing is
associated with a specific wire size.

NOTE: If you do not have the package the wires nuts came in,
visit the manufacturers website to try to locate the information
needed to answer the above questions.

17
Cables that have two current-carrying conductors (hot and ACTIVITY#10
neutral) plus equipment grounding conductor are used for 120-
volt branch circuits while cables having three current-carrying Symbols and Markings on Wires and Cables
conductors (two hot and neutral) plus grounding conductor are
1. Things needed
used for 240-volt branch circuits. Three-wire cable is not only
pencil
used for 240-branch circuits, it is often used in the wiring of
this manual
120-volt lighting circuits where three-way switches are being
used to control lights from two locations. Three-way switches
2. What you will do
will be discussed a little later in this manual.
a. With a parent or 4-H electric leader, visit a local
electrical supply or hardware store to see what
The ma rkings on some NM ca bles are embossed i n the jacket types of wires and cables are available to the
(not pri nted) and are a bit difficult to read. This one reads: consumer.
AWG 12 CU 2 CDR WITH AWG 12 GROUND TYPE NM-B 600 VOLTS
b. Choose several different cables and/or wires
and list them in the following table.
c. For each cable and/or wire you listed, identify
in the space provided, what the symbols (coding)
mean for each cable or wire. If necessary, ask for
assistance from store personnel or research the
Figure 17 NM-B Cable Two-wire plus ground
answers in the library or on the internet.

3. Check
a. Ask your parents or 4-H leader to review your
work. Did the leader suggest any changes? If
yes, what were the suggested changes?

Figure 18 NM-B Cable Three-wire plus ground

Note the markings on the outer insulating jacket. These indicate

the type of wire, the number of current carrying conductors, the
AWG, the maximum working voltage, and a few other items.

Wire - AWG Wire Insulation Color Wire or

Type of Wire
or or Sheathing M eaning of the Code Purpose for which the wire/cable
(Copper,
Cable - might be used
Aluminum) Sheathing Color Coding
AWG/#Conductors

18
 grounding conductors to be tied to the box with either a Grounding
Electrical Boxes Clip or a Grounding Screw. Code requires that individual wires
to extend into the box past the clamping device by at least six
Electrical boxes are recessed into walls to hold switches, inches and the sheath to extend at least inch past the clamping
receptacles, or fixtures (Figure 19). Boxes serve to protect device.
the connections made to these devices and to isolate them
from any flammable material in case arcing would ever occur
due to a connection becoming loose. Electrical boxes (made
of plastic, metal, or fiberglass) must be covered yet remain
Receptacles
accessible. A cover plate (or the baseplate for a lighting
fixture) is placed over the front of the box to keep the Receptacles or plug-in outlets supply electricity to lamps, radios
current-carrying parts out of contact with any individuals. or other small appliances through the cord and plug to which they
are connected. General purpose and small-appliance receptacles
Wires should never be crowded into an electrical box. In come in both two-slot (non-grounding) and three-slot (grounding)
fact, the Electrical Code specifically limits the number of varieties. Receptacles are rated for specific amperage, voltage, and
wires that a box can contain in order to prevent them from type of wire to be used. They should be marked with the U.L.
becoming damaged. Every electrical box has a parameter marking to show they have passed the requirements of the
associated with it called "box fill." Box fill is the maximum Underwriters Laboratory's safety standards.
number of conductors of a given wire size that is permitted
to be contained in a specific-sized box. The most common receptacle is the standard grounding duplex
receptacle. Duplex means that there a two sets of connections
Boxes come in various device capacities. Where more than available from which power can be taken. Figure 20 shows a pair
one wiring device is to be installed at a single location,
of polarized grounding-type duplex receptacles on the left along
"multiple-gang" boxes are used. A box chosen to contain a
single device such as a duplex receptacle would be called a with a pair of polarized non-grounding type receptacles on the
"single-gang" box. A box selected to hold two wall right. Note that the rectangular slots on polarized-type receptacles
switches, for example, a "two-gang" box. Nonmetallic are of different sizes. The longer slot is for the neutral connection;
boxes are available in one-gang through four-gang. the shorter slot is for the hot (energized) connection; and where
there is a partially-round hole, it is for the grounding connection.
Metal boxes come only as one-gang or two-gang (called a The receptacles with the T-shaped neutral slot are used with
"square box") but they do have the ability to be ganged 120-volt, 20-amp branch circuits. This allows for 20-amp plug and
together to form larger boxes by removing the sides of cord-connected devices to be used. The neutral prong (of the plug)
adjacent boxes. Although metal boxes are readily available, of a 20-amp device would be turned 90 degrees, not allowing it to
today, most residential wiring is done using nonmetallic be accidentally plugged in to a 15 amp circuit.
boxes.

Romex
Connector

Grounding
Screw

Grounding
Clip

Figure 19 Metal and Plastic Electrical Boxes Figure 20 Duplex Receptacles

Some 120-volt appliances and devices (a toaster or table lamp, for

Electrical boxes must have a clamping device to secure the example) use a two-pronged plug to connect to the receptacle. A
cable to the box. For plastic boxes, the clamp is typically two-pronged polarized plug when connected to a polarized
molded into the back corners of the box. Metal boxes use a receptacle will not allow it to be inserted into the receptacle
Romex Connector which is placed into a hole (called a backwards. If it were possible to insert the plug of a table lamp
knock-out) in one of the sides or in the top or bottom of
backwards, then the screw shell that holds the bulb would end up
the box and is secured to the box with a nut. A clamp,
being connected to the energized conductor and would create
tightened down onto the cable with screws, holds the cable
securely to the box. Metal boxes require that the potential safety issues when replacing a bulb. Remember, not all
two-pronged plugs are polarized, especially on older appliances
and devices.
19
Most often, duplex receptacles are side-wired (Figure 21). The National Equipment Manufacturers Association (NEMA) has
They are equipped with several terminal screws that are used produced a set of standards to which todays receptacles and
to attach the wires. Hot wires are attached to the brass (gold- matching plugs mechanically and electrically conform. You can
colored) screws, neutral wires to the silver screws and the do an internet search for NEMA Connector Identification to
grounding wire is attached to a separate green screw. learn more about the various receptacles and plugs available and
their ratings.
A Connecting tab causes the two brass screws to be tied
together electrically. The same is true for the two silver
screws. This means you can place your wires under either of ACTIVITY#11
the silver screws and under either of the brass screw to make
your connections. Identifying Different Receptacles Available

Ground 1. Things needed

Terminal pencil
Grounding Screw
this manual
reference materials or a visit to your local hardware
Brass Screws - or electrical supply store
Hot Wire
Silver Screws - 2. What you will do
Neutral Wire a. For each of the receptacle configurations (the
combination of amps/volts/wires) listed below,
draw the receptacles slot configuration.

Connecting Tab
2 Pole 2 Pole 3 Pole
(Non-grounding) (with ground) (with ground)
Neutral Terminal
Hot Terminal 120 Volts 120 Volts 240 Volts

Figure 21 Anatomy of a Duplex Receptacle

15
ampere
For split-circuit receptacle installations (one-half controlled
by a switch), the tab connecting the brass screws is removed.
Using long-nose pliers, as shown in Figure 22, the tab can be
bent back and forth several times until it has broken off. The 20
hot wire connects to one of the brass screws The other brass ampere
screw receives power from the switch using what is called a
switch loop.

30
ampere

3. Check
a. What was your source of information
(i.e., electrical supply store, library book)?

Figure 22 Making a Split-Circuit Receptacle

For split-circuits installations used with switches, only the
connecting tab that is attached to the brass screws will be
removed; the connecting tab between the silvers screws is
normally not removed.
20
 b. Did you have any difficulty locating information Take a look at Figures 24 and 25. These two illustrations
on any of the receptacles? If yes, which ones? show the most common ways that single-pole switches are
used to control the power supplied to a light. Figure 24
shows a circuit where the supply power is being fed into
the electrical box that contains the switch. Figure 25 shows
a circuit where the supply power is being fed into the
electrical box to which the lighting fixture will be attached.
The ground wires are omitted from the illustrations for
visual clarity.

Sometimes it can be confusing when working with

Switches switches. Often the wires used to connect to the switch are
those contained in a single NM-type cable (Figure 25). This
means that one of the wires connected to the switch would
Switches are used to control the flow of electricity in many of have white insulation. While the white wire is normally
the circuits in your home. They can be basic switches that reserved for the non-energized neutral conductor, a white
simply turn lights or receptacles on and off, or they can be wire is also allowed to be used as an energized conductor as
more complex and perform additional functions. Some long as is marked with a black band to indicate that it is an
switches have additional circuitry built in to them that allows energized conductor.
the lights in a room to be dimmed in order to set the rooms
mood or to save energy. Others contain a timer that allows Figure 24 shows a wiring schematic plus an illustration
power to be supplied to a light or another device for a certain showing two sections of NM cable running into the
amount of time. Some switches can even be operated by touch switchs electrical box. One comes from the power source
and there is no button to push or handle (toggle) to flip.
and the other comes from the lighting fixture. The black
Switches come rated for specific amperages, voltages, and
wire from each cable is connected to a brass screw on the
types of wires that can be used. switch. The two white neutral conductors are connected
together using a wire nut inside the switchs electrical box.
In general, there are four basic types of switches available for
use with home wiring: Single Pole, Two Pole, Three-Way, and
Four-Way. Lets take a look at these now.

1. The Single Pole Switch: (Figure 23) This type of

switch controls a light or receptacle from a single
location. Its toggle is marked with the labels ON and
OFF and it has two brass-colored screw terminals
used to attach the wires. The energized supply (hot)
wire connects to either one of the brass screw terminals
and the other wire (the switched wire) connects to the
other terminal and goes from there to the light or
receptacle. The grounding wire connects to the metal
part of the switch body using a green screw. Switch Switch

Power Feed Power Feed

Figure 24 Switching a light Power fed at the switch

Figure 25 shows a wiring schematic plus an illustration

showing two sections of NM cable entering the lighting
fixtures electrical box, one coming from the power source
and the other going to the switch. In this case, the white wire
in the cable going to the switch, serves to extend the
energized hot conductor to the switch. Notice that the hot
wire from the source is tied to the white wire in the second
Figure 23 Single Pole Toggle and Rocker Switches NM cable with a wire nut.

21
 Power
Feed
Power
Feed

WLV to redraw

Figure 25 Switching a light Power fed at the light

You will notice that white wire in the cable going to the switch
has been clearly marked with a black band at each end. This
indicates that it has become a part of the always energized
part of the circuit. This marking is usually done with black
Power Feed Power Feed
electrical tape, but might be made with a black permanent
marker or other approved marking method. Notice that both Figure 27 Three-way Circuit Power fed at first switch
ends have been marked.

NOTE: With any type of switch, only the energized Three-wire (with grounding wire)
conductor(s) should be switched. Never place a switch NM cable is typically used when
within a neutral conductors path. wiring three-way switches. Power Feed

2. Three-Way Switch: (Figure 26) The next most common Figure 27 shows a three-way
type of switch used in home wiring is the three-way circuit with power being brought
switch. This type of switch allows you to control a light in at the first switch. The red and
from two separate locations, usually opposite ends of the black wires in the three-wire NM
same room or at the top and bottom of a stairway. There cable are the traveler wires. The
are no ON or OFF markings on a three-way switch. black wire from the source is
Just like the single-pole switch, a three-way switch has connected to the common
two brass-colored screws but also has one additional terminal of the first switch. The
screw terminal that is either black or copper in color. This black wire coming from the
additional screw is called the Common Terminal. The lights electrical box is connected
wires that get connected to the brass screws are called the to the common terminal of the
Traveler Wires. second switch. The neutral wire is
carried through from the source
all the way to the lamp fixture.

Figure 28 show a three-way

circuit with power being brought
in at the lamp. Notice how the
white wire that is attached to the
Common Terminal
sources energized wire is marked
Black or Copper-
colored screw with black tape to show it is also
energized. The two traveler
wires are the red wire and the
Figure 28
white wire in the three-wire NM
Three-way Circuit
cable that has been marked with Power fed at the light
red tape to identified as one of the
traveler wires. The neutral wire
goes from the source directly to
Figure 26 Three-way Switch the lamp fixture.

22
 3. Four-Way Switch: (Figure 29) A four-way switch IMPORTANT SAFETY GUIDELINES
allows you to control lights or receptacles from three of
more locations such as a large living room or workshop. It 1. Dont attempt any electrical project unless you fully
has four brass-colored screws for connecting the wires. understand how to complete it. If required by Code,
Just like the three-way switch, it has no ON or OFF have it checked by the local inspector. Complicated
markings. Only one four-way switch is needed for control electrical work may require the help of a competent
from three locations. The other two switches needed in the electrician. In some locations, only licensed electricians
circuit are both three-way. This manual will not go into are allowed to perform major electrical work.
the wiring of four-way switch circuits since it is fairly
complex; you can research it on your own if you are 2. Dont attempt to work on a live circuit. Before doing
interested. any electrical work or repairs, shut off the electricity to
the circuit on which you will be working. This may
require removing a fuse or shutting off the circuit
breaker at the service entrance panel. Keep the power
off until the job is completed. (It is a good practice to
make a note at the breaker box indicating that work is
being done on a circuit.)

3. Before touching any wires, use a voltage testing device

(voltmeter, neon tester, non-contact voltage tester) to
make sure the power is off to the circuit.

4. Do stand on dry boards or rubber mat before touching

the service entrance panel or working with electricity if
there is even a slight chance that the floor may be damp
or wet.
Figure 29 Four-way Switch 5. Metallic plumbing pipes should be grounded to the
electrical system; use caution around them.
4. Double-Pole Switch: A double-pole switch is used with
240 volt appliances and motors. It looks like a four-way 6. When the project or repair is completed, test the circuit
switch with its four brass screws, except that it has ON with an electrical tester to make sure that everything is
and OFF markings on its toggle. It switches both of the in good working order.
hot wires at the same time. You can think of it as two
single-pole switches operated at the same time by the 7. Do install ground fault circuit interrupters (GFCI) to
same toggle. protect against electric shocks in bathrooms, kitchens,
garages, outdoor circuits and other places as required by
Code.
When to Replace a Switch or Receptacle
Switches and receptacles must be replaced if they are 8. Do use only wire and electrical accessories stamped
malfunctioning, cracked, or broken. Examples of problems with U.L., indicating that the product has been tested
and approved by Underwriters Laboratory.
requiring further investigation:
hot faceplate
9. Do not attach two or more wires under the same screw;
loose outlet connection - appliance plug slips out of
instead, use a short piece of wire (a pigtail) and
or is easily pulled from outlet
connect it along with the other wires using a wire nut
switch that arcs or sparks or causes light controlled by it
or other approved splices.
to flicker
switches or receptacles that don't work

In general, when replacing a switch or receptacle, replace it

with the same type - check ratings. For example, if your house
is fitted with two prong (ungrounded) receptacles, you cannot
replace them with three prong (grounded) receptacles since
there may be no grounding wire in the circuit. If updating
circuits, it is necessary to follow Code. This would most likely
require updating circuits to accept three prong receptacles or
make use of Ground Fault Circuit Interrupters (GFCI).

23
Putting it Together 3. Check
a. Ask your mom, dad, or 4-H electric leader
By now you should have learned about the circuits in your to review your diagrams and explanations.
home, how many appliances of various wattages can be tied What comments and suggestions did they
into a circuit, what size and kind of conductors should be share with you?
used in a circuit, how receptacles and switches are wired,
and how to make sure that a circuit is dead (not energized)
before working on it. In this next activity, you will use these
skills to redesign your bedroom.

ACTIVITY#12
Redesigning Your Bedroom b. Did you find any receptacles or switches that
you feel needed to be replaced? If yes, why
should they be replaced?
1. Things needed
pencil
paper
this manual

2. What you will do

a. How would you change the electrical circuit(s)
in your bedroom (or another room) if you
could? Changes may include the addition,
deletion or movement of switches, receptacles, Things to remember
lights or appliances. The National Electric Code makes specific
suggestions on the distance between receptacles,
numbers allowed per circuit size, etc. For more
specific information on these suggestions, refer
to the NEC or your local code.

b. On a piece of paper, draw your bedroom

showing all the existing circuits with the
receptacles, switches, and fixtures (using the
symbols from activity 1). (HINT: See activity 2)
c. Check each receptacle and switch using the
procedures identified previously in this manual.
(HINT: See activity 7)
d. On another piece of paper, diagram your
bedroom showing any changes you would like to
make to the existing circuit(s).
e. Explain why you would make these changes. Do
you think the changes would make your room
more convenient or desirable, etc.?

24
 4-H CLUB RECORD

Electric Project
Division V

NAME _________________________________________________ AGE_______________ YEAR _________

NAME OF CLUB ________________________________________ YEARS IN CLUB ____________________

TOWNSHIP _______________________________________ COUNTY ________________________________

I have reviewed the progress of this record and believe it to be correct:

Signature of Leader _________________________________________________________ Date _____________
Signature of Leader _________________________________________________________ Date _____________
Signature of Leader _________________________________________________________ Date _____________

Demonstration you gave on something you learned in the electric project this ye ar.
Title or subject _______________________________________________________________________________
Given before: Local 4-H Club ________________________ County electric meeting ______________________
County demonstration contest ________________________ Other organization __________________________
How many times given? ______________________

FIELD TRIPS
To where ______________________________________________________________________________

What new things did you learn about electricity on the field trip? ________________________________________
_____________________________________________________________________________________________

25
What did you learn?
1. A light fixture can be controlled from three separate locations by installing what types of switches?

2. When replacing a receptacle you encountered two brass, two silver and one green screw on the receptacle.
The wires are black, white and bare copper. Which wire(s) should be connected to the brass screws?

Which wire(s) should be connected to the silver screws?

Which wire(s) should be connected to the green screw?

3. Determine the number of circuits, the type of circuits, and the size of breaker (or fuse) needed for each
circuit for a kitchen with the following appliances: microwave, popcorn popper, coffee maker, dishwasher,
refrigerator, toaster, food processor, and electric fry pan. (Note: if the wattage is not listed on the
appliances nameplate you will need to calculate the watts using the formula: volts x amps = watts.)

ITEM VOLTS AMPS WATTS

microwave 120 7.7
popcorn popper 120 12.0
coffee maker 120 7.0
dishwasher 120 12.5
refrigerator 120 6.5
toaster 120 7.5
food processor 120 2.5
electric fry pan 120 10.0

Draw a diagram, in the space provided, of each circuit with the breaker (or fuse) size and appliances connected to
each. (NOTE: Indicate which appliances on each circuit cannot be used at the same time.)

26
27
Appendix 1.

Replacing an Outlet/Receptacle
Materials and Tools Needed:
screwdriver Replacing an existing receptacle (outlet) is a relatively simple
needle nose pliers procedure. Always replace any receptacle with the same type
outlet tester (same ratings, not necessarily the same brand) as the one you
new receptacle are removing. Most outlets in the home will be duplex (accepts
sandpaper two plugs). Make sure that the new receptacle is U.L. approved.

Replacing an End of the Run Receptacle

An end of the run receptacle is an outlet at the end of a circuit. There may be three conductors coming into the
box: one black-insulated current carrying conductor(wire), a white-ins ulated grounded conductor, and a bare or
green-insulated grounding conductor.

Removing receptacle from the wall:

1. Turn off power to the circuit containing the receptacle which you are about to replace. This can be done by
flipping the correct breaker or removing the correct fuse. If in doubt, turn off all the power in the house.
2. Using an outlet tester (or other voltage testing device), double check to make sure that the receptacle is dead.
3. Remove the screws holding the cover plate.
4. Remove the cover plate.
5. Remove the mounting screws attaching the receptacle to the box.
6. Pull the receptacle away from the box as far as the wires will easily allow.
7. Loosen the hot, neutral and grounding terminal screws and unhook the wires from the old receptacle.

Note: The black wire should be attached to the brass terminal; the white wire should be attached to the
silver terminal; the grounding wire (bare copper or green) should be connected to the grounding terminal
located at one corner of the receptacle. If you are looking at the receptacle because a polarity checker test
indicated a wiring problem, examine the connections to see if the wires were incorrectly attached. If they
were, simply reconnect the wires to the proper terminals following the procedure outlined below.

Installing a new receptacle:

1. Scrape the bare ends of the wires to remove dirt and corrosion. Sometimes a better way is to use a fine-grit
sandpaper to remove dirt and corrosion from the wires.
2. Loosen the screw terminals on the new receptacle as much as possible but do not remove them.
3. Hook the white wire around the shank of the silver-colored terminal screw. Be sure the end of the hook faces
in the same direction that the terminal screw tightens (clockwise). Tighten the screw on the wire securely.
4. If the receptacle is a grounding type, connect the grounding wire (copper or green) to the green grounding
terminal screw. Be sure the end of the hook faces in the same direction that the terminal screw tightens
(clockwise). Tighten the screw on the wire securely.
5. Hook the black wire to the brass terminal on the opposite side of the receptacle. Be sure the end of the hook
faces in the same direction that the terminal screw tightens (clockwise). Tighten the screw on the wire securely.
6. Recheck your connections. An error in connecting the wires could cause a short circuit.
7. Fold the wires as needed to get any excess length of wire back into the box, then push the receptacle into the outlet
box. (NOTE: Make sure any grounding conductor(s) stay well clear of the hot terminals on the receptacle.)
8. Replace the mounting screws and secure the receptacle to the box.
9. Replace the cover plate and screws.
10. Turn on power to the receptacle.
11. Use an outlet tester (or other voltage testing device), to check for correct polarity and grounding.
28
Replacing a Middle of the Run Receptacle
Replacing a middle of the run receptacle is similar to replacing an end of the run receptacle except there are more
wires involved. These extra wires (black and white) supply electricity to another receptacle(s) further down-stream in
the circuit. In addition to the extra hot and neutral wires, there are incoming and outgoing grounding wires.

Removing receptacle from wall:

Follow the same steps as with the end of the run receptacle. You will have two black and two white wires in the
box (one coming from the previous receptacle and one going to the next). You may notice the two black wires are
pigtailed together with a third short black wire (using a wire nut) which goes to one of the brass screws. If there
is no pigtail, the two wires would simply be attached individually to the two brass screw terminals on the
receptacle. Like the black wires, the white wires may be pigtailed together with a third wire or attached
individually to silver screw terminals.

If non-metallic (plastic, fiberglass) boxes are being used, the two grounding wires (bare or green insulated) in the
NM cable must be tied together with a third short wire (bare or green insulated) in a pigtail using a wire nut. The
third wire connects to the grounding screw on the receptacle.

If metal boxes are being used, the grounding conductors in the NM cable would be pigtailed together with two
short bare or green-insulated grounding conductors. One of the short wires is connected to the green-colored
machine screw on the receptacle. The other is secured to the box with a grounding clip or a green machine screw
using the threaded hole in the back of the box.

Installing a new receptacle:

NM cable to
Follow the same steps as in the end of the run next receptacle
receptacle. in the circuit

Remember that the two black wires and the two

white wires may be connected with a pig-tail so
that only one black and one white wire will
need to be connected to the proper screws on
the receptacle or, all each of the four of the
wires may go to individual screws. The pigtail
method is the preferred method and is used
most often today.

Remember, for non-metallic boxes, the

grounding conductor is simply attached to the
grounding terminal on the receptacle. For metal
boxes, a short grounding wire must be attached
to the grounding terminal on the receptacle and
another short grounding wire must be attached
to the electrical box.

Note: When using a metal box, the grounding

conductors in the NM cables must connect to
the grounding screws on both the box and the
receptacle. Notice how the next size larger (red) NM cable from previous
wire nut is being used to connect four wires. receptacle in the circuit

29
Appendix 2. Replacing Switches

Materials and Tools Needed Switches that are too loud or malfunctioning in some way need to be
screwdriver replaced. Replacing a switch is a relatively simple procedure. Switches
needle nose pliers are standardized so they will fit all boxes and faceplates. It is critical
new switch that switches are replaced with the same type (not same brand). Check
sandpaper amperage ratings and wire type on the switch that is being replaced and
wire stripper make sure the new switch has U.L. approval.

Replacing Single Pole Switches with Terminal Screws

To remove the old switch from the wall:

1. Turn off power to the circuit containing the switch which you are about to replace. This can be done by flipping
the correct breaker or removing the correct fuse. If in doubt, turn off all the power in the house.
2. After turning off power to the circuit, double-check that power is off by turning the light switch to the on
position. If the light comes on, you have turned off the wrong circuit. You need to locate and turn off the correct
breaker or remove the correct fuse and then re-test for the power being off.
3. Remove the screws holding the cover plate.
4. Remove the cover plate.
5. Remove the mounting screws attaching the switch to the box.
6. Pull the switch away from the box as far as the wires will easily allow.
7. Loosen the two brass-colored terminal screws and the grounding terminal screw and unhook the wires from the
old receptacle.

Note: There are two black wires attached to the terminals; the grounding wire (green or bare copper) will be
attached to the green screw on the new switch.

To install a new switch:

1. If needed, removed enough insulation from the wires so that they can wrap three-quarters of the way around
the screw terminals. Clean the bare ends of the wires with fine sandpaper to remove dirt and corrosion.
Bend the wires into little loops with the pliers so they can be hooked around the screws.
2. Fully loosen (but dont remove) the screw terminals from the new switch.
3. Hold the switch so that the "OFF marking on the toggle will be at the top.
4. Connect the wires to the screw terminals. The black wires can be placed under either screw. Be sure the
end of the hook faces in the same direction that the terminal screw tightens (clockwise). Tighten the screws
on the wires securely.
5. If the switch is grounded, connect the grounding wire to the green screw on the new switch. Be sure the end
of the hook faces in the same direction that the terminal screw tightens (clockwise). Tighten the screws on
the wires securely.
6. Recheck your connections. An error in your connection could cause the circuit breaker to trip or the fuse to
blow.
7. With the switch in its off position, align the switch so that OFF is pointed toward the ceiling. Fold the wires
as needed to get any excess length of wire back into the box, then push the switch into the electrical box.
(NOTE: Make sure any grounding conductor(s) stay well clear of the hot terminals on the switch.)
8. Replace the mounting screws and secure the switch to the box.
9. Replace the cover plate and screws.
10. Turn on power to the circuit.
11. Test the switch by moving it on and off several times and observing the light.

30
Replacing Three-way Switches

To remove the old switch from the wall:

1. Turn off power to the circuit containing the switch which you are about to replace. This can be done by flipping
the correct breaker or removing the correct fuse. If in doubt, turn off all the power in the house.
2. After turning off power to the circuit, double-check that power is off by turning the light switch to the on
position. If the light comes on, you have turned off the wrong circuit. You need to locate and turn off the correct
breaker or remove the correct fuse and then re-test for the power being off.
3. Remove the screws holding the cover plate.
4. Remove the cover plate.
5. Remove the mounting screws attaching the switch to the box.
6. Pull the switch away from the box as far as the wires will easily allow.
7. Loosen the two brass-colored terminal screws, the black or copper-colored common terminal screw, and the
grounding terminal screw and unhook the wires from the old receptacle.

Note: there should be four wires connected to the old switch. Two of these wires will be connected to brass
terminal screws while the third will be fastened to a black or copper colored terminal screw, and the last to the
grounding terminal screw. Mark the wire connected to the black or copper-colored screw with a piece of tan
masking tape so that you wont lose track of where it goes. (Other wires may have colored tape on them.)

To install a new switch:

1. If needed, removed enough insulation from the wires so that they can wrap three-quarters of the way around
the screw terminals. Clean the bare ends of the wires with fine sandpaper to remove dirt and corrosion. Bend
the wires into little loops with the pliers so they can be hooked around the screws.
2. Fully loosen (but dont remove) the terminal screws from the new switch.
3. Connect the wires to the screw terminals. Make sure that the wire you marked with the tape goes back on the
terminal with the black or copper-colored screw. The other two wires go to either of the brass screws and
the grounding wire goes to the green screw. Hook wires securely around the screws. Be sure the end of the
hook faces in the same direction that the terminal screws tighten (clockwise). Tighten the screws on the
wires securely.

3-Way Switch Middle of the Run

(See Figure 28 for complete circuit) Common terminal

Traveler wires
(Can connect to either
brass screw terminal) NM cable to box
with light and
power feed
NM cable to other 3-way
switch in the circuit

31
 Note: Three-wire plus ground type NM cable is often used for wiring three-way switches with the white and
red wires in these cables being used in very specific ways. The wires going to the brass-colored screws may
not both have black insulation; one could be black and another black but marked with a red stripe or else
one could be red and another white but marked with a red stripe. It is OK to reverse either of the two wires
going to the brass screw terminals without affecting the switchs function.

4. If the switch is grounded, connect the grounding wire to the green screw on the new switch. Be sure the end
of the hook faces in the same direction that the terminal screw tightens (clockwise). Tighten the screws on
the wires securely.
5. Recheck your connections. An error in your connection could cause the circuit breaker to trip or the fuse to
blow.
6. Fold the wires as needed to get any excess length of wire back into the box, then push the switch into the
box. For a three-way switch, there is no need to orient the switch a certain direction when installing it in the
box. If you look at the toggle, you will notice it does not even have On and "Off markings.
(NOTE: Make sure any grounding conductor(s) stay well clear of the hot terminals on the switch.)
7. Replace the mounting screws and secure the switch to the box.
8. Replace the cover plate and screws.
9. Turn on the power to the circuit.
10. Test the switch by moving it on and off several times and observing the light. Go to the other three-way switch
that controls the light and test the light from that switch as well.

32
Replacing Light-Dimmer Switches

Materials and Tools Needed

screwdriver
Dimmer switches allow the intensity of the
needle nose pliers
new dimmer switch light to be controlled. This is desirable to
sandpaper save energy and to create moods.
wire stripper

To remove the old dimmer switch from the wall:

1. Turn off power to the circuit containing the switch which you are about to replace. This can be done by flipping
the correct breaker or removing the correct fuse. If in doubt, turn off all the power in the house.
2. After turning off power to the circuit, double-check that power is off by turning the light switch to the on
position. If the light comes on, you have turned off the wrong circuit. You need to locate and turn off the correct
breaker or remove the correct fuse and then re-test for the power being off.
3. Remove the screws holding the cover plate.
4. Remove the cover plate.
5. Remove the mounting screws attaching the switch to the box.
6. Pull the switch away from the box as far as the wires will easily allow.
7. Loosen the two brass-colored terminal screws and the grounding terminal screw and unhook the wires from
the old receptacle. If the dimmer switch does not have screw terminals but has leads instead, remove the wire
nuts and disconnect the wires.

Note: there are two black wires attached to the terminals; the grounding wire (green or bare copper) should
be connected to the green screw on the new switch. Some dimmer switches come with short black wires
extending out from the body of the switch. In this case, the switch is connected into the circuit using wire
nuts.

Note: Some dimmer switches may not use screw terminals but instead have two

To install a new dimmer switch:

1. If needed, removed enough insulation from the wires so that they can wrap three-quarters of the way around
the screw terminals. Clean the bare ends of the wires with fine sandpaper to remove dirt and corrosion. Bend
the wires into little loops with the pliers so they can be hooked around the screws.
2. If the dimmer switch has screw terminals, loosen (but dont remove) the screws on the new switch.
3. Hook the wires securely around the screws. Be sure the end of the hook faces in the same direction that the
terminal screws tighten (clockwise). Tighten the screws on the wires securely.
4. Most dimmer switches have two wires corning from them. These wires are connected to the permanent wires
with wire nuts. Either wire coming from the switch can be connected to either of the permanent wires.
5. Recheck your connections. An error in your connection could cause the circuit breaker to trip or the fuse to
blow.
6. Fold the wires as needed to get any excess length of wire back into the box, then push the switch into the box.
7. Replace the mounting screws and secure the switch to the box.
8. Replace the cover plate and screws.
9. Install the control knob.
10. Turn the power on to the circuit.
11. Test the dimmer knob by turning it on and off several times.

33
Appendix 3. Wiring Around Your Home
Glossary of Electrical Terms related to Residential Wiring

Ampacity: The current in Amperes that a conductor can carry continuously under the conditions of use without
exceeding the conductors temperature rating.
Ampere: The measurement of the rate of flow of current in an electrical circuit. One Ampere is the
measurement of the rate at which current that will flow through a resistance of 1 Ohm when an electrical
potential of 1 Volt is applied across that resistance. Sometimes this term is shortened to the word Amp.
Arc-Fault Circuit Interrupter (AFCI): A device that is able to sense when an electrical arc occurs somewhere in a
circuit and acts to de-energize the circuit connected to it.
AWG (American Wire Gauge): This is the industry standard used to specify the size of electrical conductors.
There are 40 different electrical conductor sizes ranging from 36 AGW (smallest) to 0000 AWG (largest). Each
consecutive AGW size is 1.26 times smaller or bigger in diameter than the next. The larger the diameter, the
greater the conductors current carrying capacity (ampacity).
Ballast: A device that is an integral part of a fluorescent light. It is used to regulate the amount of current which
is allowed to flow though the light.
Bonding: Connecting the metal parts of electrical components together to assure electrical conductivity
between them. It is the practice of intentionally electrically connecting all exposed metallic items not designed
to carry electricity in a room or building as protection from electric shock.
Bonding Jumper, Main: This is a connection made between the grounded circuit conductor (Neutral) and the
equipment grounding conductor inside the service entrance panel.
Branch Circuit: Consists of the circuit conductors that are between the final overcurrent device (fuse/circuit
breaker) protecting the circuit and the outlet(s) which are part of that circuit. There are three types of branch
circuits General Purpose, Small Appliance, and Individual.
Circuit Breaker: A circuit protection device that is designed to either be 1) manually operated to open or close a
circuit; or 2) automatically open a circuit when a predetermined overcurrent flows through the circuit. These
are most often used inside the service entrance panel.
Continuous Load: An electrical load where the maximum current in a circuit is expected to continue for a
period of 3 hours or longer. A continuous load shall not exceed 80% of the rating of the branch circuit.
CU: a marking on wire connectors, lugs and device terminals that indicates they are suitable for use with
Copper conductors only.
Current: The flow of electricity (electrons) through an electrical circuit. Current is measured in Amperes.
Dedicated Circuit: See Individual Branch Circuit.
Duplex Receptacle: An electrical outlet that allows two plug-and-cord-connected devices to be connected to
the house wiring system and receive power at the same time.
Floor Plan: A scale diagram of a room or building drawn as if seen from above. Floor plans show construction
details such as placement of plumbing, the electrical system, and doors and windows.
Fuse: An overcurrent protection device with a fusible link which melts during an overcurrent condition in a
circuit in order to stop the flow of electricity. Fuses can often be found in older service entrances panels and
come in various ratings and form-factors.
Ground: The earth. It is used as the common reference point for measuring electrical potential (voltages)
within an electrical system.

34
Grounded (Grounding): Connected to the ground or connected to an electrically conductive item that
physically extends the connection to the ground.
Grounded Conductor: (Not to be confused with Grounding conductor.) For residential wiring, this is the
Neutral wire which is the one with the white insulation.
Ground Fault: An unintentional, connection between a current carrying conductor and non-current carrying
(grounded) parts of an electrical system (other conductors, metal enclosures, conduit, earth, etc.) causing
current to flow on an unintended path (Ground-Fault Current Path).
Ground Fault Circuit-Interrupter (GFCI): A device used to protect persons from the risk of bodily injury by de -
energizing a circuit within a very short period of time when the current flowing to ground exceeds .006
amperes.
Ground-Fault Current Path: The path on which fault current flows beginning at the point of the ground fault
and flowing through normally non-current carrying parts of the electrical system back to the electrical supply
source.
Grounding Conductor: A conductor that is used to connect equipment or the grounded circuit of a wiring
system to the grounding electrode or electrodes. In residential wiring, this is typically a 4 AWG 8 AWG bare
copper wire.
Grounding Electrode: A conducting material making a direct connection to the earth. This could be a metal
water pipe, concrete-encased bare copper conductor, or a ground rod. Ground rods must be at least 0.5 in
diameter and at least 8 long.
Individual Branch Circuit: A branch circuit that supplies only one piece of utilization equipment (such as an
electric range). Typically, a single receptacle (not a Duplex receptacle).
Insulated/Insulation: A non-conductive covering applied to wires or placed between conductive materials to
prevent current from leaving a conductor and flowing on an unintended path.
Lighting Outlet: An outlet intended for the direct connection of a lamp holder or luminaire.
Load: The electrical power consumed by the devices attached to an electrical system. Loads can be of several
types, the main ones being Continuous, Non-Continuous, and Intermittent.
Load Balancing: The arrangement or sequence of attaching conductors to the panelboard (service entrance
panel) in order to balance the anticipated loads on the phase conductors. With a balanced load, the connected
equipment would draw an equal current through each 120-volt leg of a 120V/240V electrical system. Generally
speaking, the simplest way to balance the load on a panelboard is to connect an equal number of branch
circuits to each phase conductor.
Load Center: Also known as a Service Entrance Panel or Residential Panel Board. Circuit breakers typically
plug-in to load centers whereas they bolt-in to panel boards.
Location Damp: An exterior or interior location that is normally or periodically subject to condensation of
moisture in, on, or adjacent to, electrical equipment, and includes partially protected locations.
Location Dry: A location not normally subject to dampness, but may include a location subject to temporary
dampness, as in the case of a building under construction, provided ventilation is adequate to prevent an
accumulation of moisture.
Location Wet: A location in which water or other liquid can drip, splash, or flow on or against electrical
equipment.
Luminaire: A complete lighting unit consisting of a light source such as a lamp or lamps, together with the parts
designed to position the light source and connect in to a power supply. Prior to the National Electrical Code
adopting this term, lighting fixture was the commonly used term. This term is still used more often than
luminaire.

35
Maximum Continuous Load: Defined to be 80% of the circuit rating (protection device). Any electrical load that
operates for a period of 3 hours or more on a branch circuit shall not exceed 80% of the circuit rating
(protection device).
National Electrical Code (NEC): The electrical code published by the National Fire Protection Association. This
code provides for practical safeguarding of persons and property from hazards arising from the use of
electricity. It does not become law until adopted by federal, state, and local laws and regulations.
Neutral Conductor: The conductor connected to the neutral point of an electrical system that is intended to
carry current under normal conditions.
Ohm: A unit of measure for electrical resistance. One Ohm is the amount of resistance that will permit one
Ampere of current to flow when one Volt is applied across the resistance.
Open Circuit: A circuit that does not have a continuous path over which current can flow. Turning off a switch
creates an open circuit (good), while a loose connection also can create an open circuit (bad).
Outlet: A point on the wiring system at which current is taken to supply utilization equipment.
Overcurrent: Any current is excess of the rated current of the equipment or the ampacity of a conductor.
Overcurrent Device: Also referred to as an Overcurrent Protection Device and is a form of protection that
operates when current exceeds a pre-determined value. These devices are primarily consist of circuit breakers
and fuses.
Overload: Operation of equipment in excess of the normal full-load rating, or of a conductor in excess of its
rated ampacity, that over time, would cause damage or dangerous overheating.
Receptacle: A receptacle is a contact device at the outlet for the connection of an attachment plug.
Receptacle Outlet: An outlet where one or more receptacles are attached.
Romex: A trade name for Nonmetallic Sheathed Cable (NM).
Service: The conductors and equipment for delivering energy from the servicing utility to the wiring system of the
premises served.
Service Conductors: The conductors running from the service point to the service disconnecting device.
Service Drop: The overhead service conductors from the last pole or other aerial support that connect to the
service-entrance conductors at the building.
Service Entrance Panel (SEP): A metal enclosure that houses circuit protection devices (circuit breakers or fuses)
and provides the means by which power is divided up to be distributed to the individual circuits. It contains a
Main breaker that allows the power from the utility company to be disconnected from the entire building.
Service Equipment: The equipment intended to be the main control and means of cutting off of the supply of
electricity to a building. This usually consists of a circuit breaker or switch and fuse and their accessories.
Short Circuit: A connection between any two or more conductors of an electrical system in such a way as to
significantly reduce the resistance of the circuit. This situation causes the currently to flow outside of the intended
path, hence the term Short Circuit. A short circuit is referred to as a Fault.
Split-Circuit Receptacle: A standard duplex receptacle whose break-away tabs have been removed and is
connected such that one half of the receptacle supplies power all the time while power to the other half is
controlled by a switch.
Surface-Mounted Luminaire: A luminaire mount directly on (surface of) the ceiling or a wall.
Switch: A device use to control (enable or disable) the flow of electricity in a circuit or portion of a circuit.
Terminal: A screw or quick-connect device where a conductor is intended to be connected.

36
 Three-way Switch: A type of switch that is used in pairs to allow you to control the power supplied to a light or
receptacle from two different locations.
UL: Underwriters Laboratories (UL) is an independent not-for-profit organization that develops standards and tests
electrical equipment to those standards.
UL-Listed: Indicates that an item has been tested and approved to the standards established by the UL for that
particular item.
Ungrounded: Not connected to ground or a conductive body that extends to the ground connection.
Volt: A measurement of electrical potential energy. It is the difference in electrical potential between two points
of a conductor carrying one Ampere when the power being dissipated between those two points is one Watt.
Voltage (nominal): A value assigned to a circuit or system for the purpose of specifying its (nominal) operating
voltage. In residential systems the nominal voltage would be specified as 120/240 Volts. In practice, the actual
voltages can vary slightly around the specified nominal voltages.
Voltage Drop: A reduction in voltage (difference in electrical potential energy) at a given point in a circuit due to
current flowing through a resistance (typically the conductors in a circuit). The voltage drop across any given
length of conductor can be calculated by Ohms Law: E (voltage) = I (current) x R (resistance).
Watt: A unit of power. It is equal to: W (wattage) = E (voltage) x I (current).

Answers to Questions in Activity #1 (correct answer highlighted)

1. Why do two switches connect to the paddle fan?

Slow/Fast Speeds One for Light/One for Fan

2. How many lights are connected to 3-way switches?

1 4 5

3. Where are multiple lights controlled by one switch?

Garage Exterior Bath Bedroom 2

4. What two appliances are shown using 240 Volts?

Clothes Dryer, Range

5. Which five areas use GFCI-protected receptacles?

Bath, Bath, Kitchen, Garage, Front Porch

6. Which room makes use of Split-Circuit receptacles?

Bedroom 1

7. Where is the Service Entrance Panel located?

In the Garage

8. What does WP stand for on an outdoor receptacle?

Weatherproof

37
 PILOTMarch 2014

It is the policy of the Purdue University Cooperative Extension Service that all persons have equal opportunity and access to its educational programs, services, activities, and
facilities without regard to race, religion, color, sex, age, national origin or ancestry, marital status, parental status, sexual orientation, disability or status as a veteran.
Purdue University is an Affirmative Action institution. This material may be available in alternative formats.

LOCAL FACES Order or download materials from

Purdue Extension The Education Store
E XTENSION
AGRICULTURE COUNTLESS CONNECTIONS
www.the-education-store.com