Specification

Download as pdf or txt
Download as pdf or txt
You are on page 1of 3

Fuel Specification http://www.marinediesels.co.uk/members/Fuel_Oil/residual_fuel_spec.

htm

Members Section
Fuel Oil
Fuel Specification
Other Pages The Basics The 2 Stroke Engine The 4 Stroke Engine Operation Members

INTRODUCTION

Fuel burnt in diesel engines is a hydrocarbon; that is to say it is made up mainly of hydrogen and carbon. These are the
two elements which supply most of the energy when the fuel is burnt. Also present will be a small amount of sulphur (as
allowed by current legislation) plus a small amount of ash forming impurities and traces of metallic elements.

Most of the marine fuel oil used in marine diesel engines is residual fuel. Residual fuels are those products which remain
after all distillates and lighter fractions have been removed from crude oil during the refining and cracking processes.
These residues are complex mixtures which contain sediments and catalytic fines (small particles of alumino-silicates
used during the cracking process which are very abrasive).

STANDARDS

MARINE RESIDUAL FUELS

RMA a RMB RMD RME RMG RMK


Parameter Unit Limit
10 30 80 180 180 380 500 700 380 500 700
Viscosity at 50C mm/s Max 10.00 30.00 80.00 180.0 180.0 380.0 500.0 700.0 380.0 500.0 700.0

Density at 15C kg/m3 Max 920.0 960.0 975.0 991.0 991.0 1010.0

Micro Carbon
% m/m Max 2.50 10.00 14.00 15.00 18.00 20.00
Residue
Aluminium +
mg/kg Max 25 40 50 60
Silicon
Sodium mg/kg Max 50 100 50 100
Ash % m/m Max 0.040 0.070 0.100 0.150
Vanadium mg/kg Max 50 150 350 450
CCAI - Max 850 860 870
Water % V/V Max 0.30 0.50
Pour point
(upper) b, C Max 6 30
Summer
Pour point
(upper) b, C Max 0 30
Winter
Flash point C Min 60.0

Sulphur c % m/m Max Statutory requirements

Total Sediment,
% m/m Max 0.10
aged

Acid Number e mgKOH/g Max 2.5

Used lubricating
The fuel shall be free from ULO, and shall be considered to contain ULO when either one of the
oils (ULO):
following conditions is met:

Calcium and mg/kg -


Calcium > 30 and zinc >15; or
Zinc; or Calcium
Calcium > 30 and phosphorus > 15.
and Phosphorus

Hydrogen
mg/kg Max 2.00
sulphide d
a This residual marine fuel grade is formerly DMC distillate under ISO 8217:2005.

b Purchasers shall ensure that this pour point is suitable for the equipment on board, especially in cold climates.

c The purchaser shall define the maximum sulphur content according to the relevant statutory requirements.

1 of 3 06-02-2017 22:21
Fuel Specification http://www.marinediesels.co.uk/members/Fuel_Oil/residual_fuel_spec.htm

d Effective only from 1 July 2012.

Strong acids are not acceptable, even at levels not detectable by the standard test methods for SAN.
As acid numbers below the values stated in the table do not guarantee that the fuels are free from problems associated
e
with the presence of acidic compounds, it is the responsibility of the supplier and the purchaser to agree upon an
acceptable acid number.

Source: ISO 8217 Fourth Edition 2010-06-15


Petroleum products - Fuels (class F) - Specifications of marine fuels

MARINE DISTILLATE FUELS

Parameter Unit Limit DMX DMA DMZ DMB

Viscosity at 40C mm/s Max 5.500 6.000 6.000 11.00

Viscosity at 40C mm/s Min 1.400 2.000 3.000 2.000


Micro Carbon Residue
% m/m Max 0.30 0.30 0.30 -
at 10% Residue

Density at 15C kg/m3 Max - 890.0 890.0 900.0

Micro Carbon Residue % m/m Max - - - 0.30

Sulphur a % m/m Max 1.00 1.50 1.50 2.00

0.30
Water % V/V Max - - -
b

0.10
Total sediment by hot filtration % m/m Max - - -
b

Ash % m/m Max 0.010 0.010 0.010 0.010


Flash point 0C Min 43.0 60.0 60.0 60.0
Pour point, Summer 0C Max - 0 0 6
Pour point, Winter C Max - -6 -6 0
Cloud point C Max -16 - - -
Calculated Cetane Index Min 45 40 40 35
Acid Number mgKOH/g Max 0.5 0.5 0.5 0.5

Oxidation stability g/m3 Max 25 25 25 25 c


Lubricity, corrected wear scar diameter
um Max 520 520 520 520 c
(wsd 1.4 at 60C d

Hydrogen sulphide e mg/kg Max 2.00 2.00 2.00 2.00

Appearance Clear & Bright f b, c

A sulphur limit of 0.1% m/m applies in the Emission Control Areas designated by the
International Maritime Organization. As there may be local variations, the purchaser shall define
a
the maximum sulphur content according to the relevant statutory requirements,
notwithstanding the limits given in this table.

If the sample is not clear and bright, total sediment by hot filtration and water test shall be
b
required.

c Oxidation stability and lubricity tests are not applicable if the sample is not clear and bright.
d Applicable if sulphur is less than 0.050% m/m.
e Effective only from 1 July 2012.
If the sample is dyed and not transparent, water test shall be required. The water content shall
f
not exceed 200 mg/kg (0.02% m/m).

NOTES
(1) A sulphur limit of 0.1% m/m will apply in SOx Emission Control Areas designated by the International Maritime Organization.

(2) The Fuel shall be free of Used Lubrication Oil (ULO). A Fuel is considered to be free of ULO if one or more of the elements are
below the limits. All three elements shall exceed the limits before deemed to contain ULO.

Previously, bunkers were ordered with an IF number e.g. IF380. The letters IF were used by some oil companies to denote
Intermediate bunker Fuel or InterFuel. The number after referred to the density in cSt at 50C. Generally speaking an RME180
corresponds to an IF180 and an RMG380 or an RMH380 correspond to an IF380.

As can be seen from the table the specification gives max and min limits for different characteristics. It is up to the person
responsible for taking the bunkers to sample the fuel using continuous drip sampling and to test for certain characteristics.
The oil can be sent away to an organisation like FOBAS (Fuel Oil Bunker Analysis and Advisory Service) for more
comprehensive testing which includes calculation of the higher and lower calorific value of the fuel.

Below is are the results of actual tests on a sample of RMG 380

2 of 3 06-02-2017 22:21
Fuel Specification http://www.marinediesels.co.uk/members/Fuel_Oil/residual_fuel_spec.htm

Property Value Limit


Viscosity 100C 31.11 mm/s2 (CSt) ( Max 35)
Viscosity 50C 300 mm/s2 (CSt) ( Max 420)
Density Kg/L 0.9899 (Max 0.9910)
Water % v/v 0.05 (Max 0.5)
Ash % m/m 0.03 (Max 0.2)
Micro Carbon Residue 13.88 (Max 18)
Sulphur % m/m 1.96 (Max 3.5)
Total Sediment % m/m 0.01 (Max 0.1)
Pour Point C <- 3 (Max 30)
Flash point C >70 (Min 60)
Gross CV MJ/kg 42.86
Net CV MJ/kg 40.56
Si (cat fines) mg/kg 13 (Max 80)
Al (cat fines) mg/kg 5 (Max 80)
Vanadium mg/kg 68 (Max 300)
Sodium mg/kg 5
Iron mg/kg 21
Phosphorus mg/kg 1
Lead mg/kg <1
Calcium mg/kg 5
Zinc mg/kg <1
CCAI 853

Note: v/v = volume for volume by proportion; m/m = mass for mass by proportion

If testing on board, then two important characteristics to test for are the density at 15 and the viscosity at 50C in cSt or
mm2/s. From these two figures the Calculated Carbon Aromacity Index or CCAI can be calculated. This figure, which
should lie between the limits of 800 and 870 give a guide to the burnability of the fuel and its ignition characteristics. The
higher the number, the longer the ignition delay, and the hotter it will burn. This number is used as a guide to setting the
fuel quality lever on the fuel pumps.

Density can be measured by a hydrometer. Usually the sample is heated to 50C and the density measured. The figure is
then corrected back to 15C.

Viscosity is measured by timing how long it takes a ball to roll down an inclined tube filled with the oil at a fixed
temperature.

For more information on fuel oil, its characteristics, and testing, click the Kittiwake Logo

DHTML Menu / JavaScript Menu Powered By OpenCube

3 of 3 06-02-2017 22:21

You might also like