CalibrationListing REL 32d International 370a430HP

Download as txt, pdf, or txt
Download as txt, pdf, or txt
You are on page 1of 161
At a glance
Powered by AI
The document describes calibration parameters for various engine sensors and systems. It includes parameters like initial values, limits, filters, and equations used for calibration.

The document describes calibration parameters for the fuel temperature sensor (FTS), air temperature sensor (ATS), oil temperature sensor (OTS), and boost pressure sensor. It includes parameters like PID pins, initial values, limits, filters, and more.

The sensors calibrated include the fuel temperature sensor (FTS), air temperature sensor (ATS), and oil temperature sensor (OTS).

CalibrationListing

File created: 12:39:10 Feb 16 2008

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
checksum 0 24647.0 HEX 6047 E C
# CHECKSUM of DDC Calibration values in EEPROM
cal_major_version 2 32.0 DEC 20 E C
calmjr major CAL & SW version must match-ie both PHASE6.X
cal_edit_version 3 6.0 DEC 06 E C
caledt CALMEM.H CAL STRUCTURE version for given SW PHASE
cal_min_minor_version 4 0.0 DEC 00 E C
calmmn minor CAL version to add new CAL vals-ie PHASEX.2
fuel_type 5 95.0 DEC 5f E C
fueltp FUELTP=95 for diesel and FUELTP=160 for gas cals
calibration_size 6 10393.0 "" 2899 E C
calsiz calibration_size
rating_edit_version 8 29.0 DEC 1d E C
rrlver Rating Section Version Number
fts_pid_pin_R3 A 174.0 PID 00ae E V
aipid Pin R3/Ct#472 Def: J1587 PID 174=FTS / 0=No Input
fts_initial_value C 1010.0 A/D 03f2 E V
aiinit FTS A/D counts used on system initialization
fts_timer E 2.0 SEC 0014 E*10 V
aitval ramp/rst SECS of FTS fault to log code if enabled
fts_rawhilimit 10 1010.0 A/D 03f2 E V
aishi FTS A/D counts > rawhilim to log FTS failed high
fts_rawlolimit 12 48.0 A/D 0030 E V
aislo FTS A/D counts < rawlolim to log FTS failed low
fts_default 14 567.0 A/D 0237 E V
aidfl FTS A/D counts used if FTS failed high OR low
fts_offset 16 0.0 N/A 0000 E V
aioff FTS nonlinear - not used
fts_gain 18 0.000 N/A 0000 U*128 V
aigain FTS nonlinear - must set to 0 for Look-Up Table
fts_scaledhilimit 1A 75.0 dgC 0679 U V
aivhi FTS degC > sclhilim to log Fuel Temp High
fts_scaledlolimit 1C -40.0 dgC 0000 U V
aivlo FTS degC < scllolim to log Fuel Temp Low
fts_filterconst 1E 0.102 % @ 0d E*128 V
aiifc FTS A/D filter: new=old+filt*(new-old) @ 25msec
fts_pad_bits 1F 0.0 "" 0 E V
padbit fts_pad_bits
fts_alt_scaledlo 1F.4 0.0 Flg 0 E V
aitvlo FuelTempLo Timer: 0=intgrtg dflt/1=local ramp/rst
fts_alt_scaledhi 1F.5 0.0 Flg 0 E V
aitvhi FuelTempHi Timer: 0=intgrtg dflt/1=local ramp/rst
fts_alt_sensorlo 1F.6 0.0 Flg 0 E V
aitslo FTS FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
fts_alt_sensorhi 1F.7 0.0 Flg 0 E V
aitshi FTS FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
fts_percent_weight_en 20 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
fts_flt_percent_weight 20.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
aux_temp_1_pid_pin_N2 22 172.0 PID 00ac E V
aipid Pin N2/Ct#132 Def:J1587 PID 172=AirTemp/0=No Input
aux_temp_1_initial_value 24 1010.0 A/D 03f2 E V
aiinit Air Temp A/D counts used on system initialization
aux_temp_1_timer 26 2.0 SEC 0014 E*10 V
aitval ramp/rst SECS of ATS fault to log code if enabled
aux_temp_1_rawhilimit 28 1010.0 A/D 03f2 E V
aishi ATS A/D counts > rawhilim to log ATS failed high
aux_temp_1_rawlolimit 2A 48.0 A/D 0030 E V
aislo ATS A/D counts < rawlolim to log ATS failed low
aux_temp_1_default 2C 144.0 A/D 0090 E V
aidfl ATS A/D counts used if ATS failed high OR low
aux_temp_1_offset 2E 0.0 N/A 0000 E V
aioff ATS nonlinear - not used
aux_temp_1_gain 30 0.000 N/A 0000 U*128 V
aigain ATS nonlinear - must set to 0 for Look-Up Table
aux_temp_1_scaledhilimit 32 250.0 dgC 1053 U E
aivhi Air Temp degC > sclhilim to log Air Temp High
aux_temp_1_scaledlolimit 34 -40.0 dgC 0000 U V
aivlo Air Temp degC < scllolim to log Air Temp Low
aux_temp_1_filterconst 36 0.102 % @ 0d E*128 V
aiifc ATS A/D filter: new=old+filt*(new-old) @ 25msec
aux_temp_1_pad_bits 37 0.0 "" 0 E V
padbit aux_temp_1_pad_bits
aux_temp_1_alt_scaledlo 37.4 0.0 Flg 0 E V
aitvlo AirTemp Lo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_temp_1_alt_scaledhi 37.5 0.0 Flg 0 E V
aitvhi AirTemp Hi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_temp_1_alt_sensorlo 37.6 0.0 Flg 0 E V
aitslo ATS FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_temp_1_alt_sensorhi 37.7 0.0 Flg 0 E V
aitshi ATS FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_temp_1_percent_weight_en 38 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
aux_temp_1_flt_percent_weight 38.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
ots_pid_pin_R2 3A 175.0 PID 00af E V
aipid Pin R2/Ct#120 Def: J1587 PID 175=OTS / 0=No Input
ots_initial_value 3C 1010.0 A/D 03f2 E V
aiinit OTS A/D counts used on system initialization
ots_timer 3E 2.0 SEC 0014 E*10 V
aitval ramp/rst SECS of OTS fault to log code if enabled
ots_rawhilimit 40 1010.0 A/D 03f2 E V
aishi OTS A/D counts > rawhilim to log OTS failed high
ots_rawlolimit 42 24.0 A/D 0018 E V
aislo OTS A/D counts < rawlolim to log OTS failed low
ots_default 44 184.0 A/D 00b8 E V
aidfl OTS A/D counts used if OTS failed high OR low
ots_offset 46 0.0 N/A 0000 E V
aioff OTS nonlinear - not used
ots_gain 48 0.000 N/A 0000 U*128 V
aigain OTS nonlinear - must set to 0 for Look-Up Table
ots_scaledhilimit 4A 115.0 dgC 08b9 U E
aivhi Oil Temp degC > sclhilim to log Oil Temp high
ots_scaledlolimit 4C -40.0 dgC 0000 U V
aivlo Oil Temp degC < scllolim to log Oil Temp low
ots_filterconst 4E 0.102 % @ 0d E*128 V
aiifc OTS A/D filter: new=old+filt*(new-old) @ 25msec
ots_pad_bits 4F 0.0 "" 0 E V
padbit ots_pad_bits
ots_alt_scaledlo 4F.4 0.0 Flg 0 E V
aitvlo OilTemp Lo Timer: 0=intgrtg dflt/1=local ramp/rst
ots_alt_scaledhi 4F.5 0.0 Flg 0 E V
aitvhi OilTemp Hi Timer: 0=intgrtg dflt/1=local ramp/rst
ots_alt_sensorlo 4F.6 0.0 Flg 0 E V
aitslo OTS FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
ots_alt_sensorhi 4F.7 0.0 Flg 0 E V
aitshi OTS FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
ots_percent_weight_en 50 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
ots_flt_percent_weight 50.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
aux_temp_2_pid_pin_P3 52 110.0 PID 006e E V
aipid Pin P3/Ct#133 Def:J1587 PID 110=ClntTmp/0=No Input
aux_temp_2_initial_value 54 1010.0 A/D 03f2 E V
aiinit Coolant Temp A/D counts on system initialization
aux_temp_2_timer 56 2.0 SEC 0014 E*10 V
aitval ramp/rst SECS of CTS fault to log code if enabled
aux_temp_2_rawhilimit 58 1010.0 A/D 03f2 E V
aishi CTS A/D counts > rawhilim to log CTS failed high
aux_temp_2_rawlolimit 5A 24.0 A/D 0018 E V
aislo CTS A/D counts < rawlolim to log CTS failed low
aux_temp_2_default 5C 184.0 A/D 00b8 E V
aidfl CTS A/D counts used if CTS failed high OR low
aux_temp_2_offset 5E 0.0 N/A 0000 E V
aioff CTS nonlinear - not used
aux_temp_2_gain 60 0.000 N/A 0000 U*128 V
aigain CTS nonlinear - must set to 0 for Look-Up Table
aux_temp_2_scaledhilimit 62 105.0 dgC 0829 U E
aivhi Coolant Temp degC > sclhilim to log Clnt Temp high
aux_temp_2_scaledlolimit 64 -40.0 dgC 0000 U V
aivlo Coolant Temp degC < scllolim to log Clnt Temp low
aux_temp_2_filterconst 66 0.102 % @ 0d E*128 V
aiifc CTS A/D filter: new=old+filt*(new-old) @ 25msec
aux_temp_2_pad_bits 67 0.0 "" 0 E V
padbit aux_temp_2_pad_bits
aux_temp_2_alt_scaledlo 67.4 0.0 Flg 0 E V
aitvlo ClntTempLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_temp_2_alt_scaledhi 67.5 0.0 Flg 0 E V
aitvhi ClntTempHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_temp_2_alt_sensorlo 67.6 0.0 Flg 0 E V
aitslo CTS FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_temp_2_alt_sensorhi 67.7 0.0 Flg 0 E V
aitshi CTS FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_temp_2_percent_weight_en 68 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
aux_temp_2_flt_percent_weight 68.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
ops_pid_pin_P2 6A 100.0 PID 0064 E V
aipid Pin P2/Ct#530 Def: J1587 PID 100=OPS / 0=No Input
ops_initial_value 6C 102.0 A/D 0066 E V
aiinit OPS A/D counts used on system initialization
ops_timer 6E 5.0 SEC 0032 E*10 V
aitval ramp/rst SECS of OPS fault to log code if enabled
ops_rawhilimit 70 990.0 A/D 03de E V
aishi OPS A/D counts > rawhilim to log OPS failed high
ops_rawlolimit 72 48.0 A/D 0030 E V
aislo OPS A/D counts < rawlolim to log OPS failed low
ops_default 74 950.0 A/D 03b6 E V
aidfl OPS A/D counts used if OPS failed high OR low
ops_offset 76 -102.0 A/D ffffff9a E V
aioff OPS A/D counts OFFSET: kpa=(A/Dfilt+OFFSET)*gain
ops_gain 78 0.488 K/C 0091 U*128 V
aigain OPS kpa/A/Dcount GAIN: kpa=(A/Dfilt+offset)*GAIN
ops_scaledhilimit 7A 127.1 KPA 0127 U V
aivhi Oil Press kpa > sclhilim to log Oil Press High
ops_scaledlolimit 7C 0.0 N/A 0000 U V
aivlo Not Used - see Oil Press low vs. RPM Look-Up Tble
ops_filterconst 7E 0.203 % @ 1a E*128 V
aiifc OPS A/D filter: new=old+filt*(new-old) @ 25msec
ops_pad_bits 7F 0.0 "" 0 E V
padbit ops_pad_bits
ops_alt_scaledlo 7F.4 1.0 N/A 1 E V
aitvlo Not Used - OilPressLo Timer=ramp/reset dflt SECS
ops_alt_scaledhi 7F.5 0.0 Flg 0 E V
aitvhi OilPressHi Timer: 0=intgrtg dflt/1=local ramp/rst
ops_alt_sensorlo 7F.6 0.0 Flg 0 E V
aitslo OPS FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
ops_alt_sensorhi 7F.7 0.0 Flg 0 E V
aitshi OPS FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
ops_percent_weight_en 80 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
ops_flt_percent_weight 80.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
tbs_pid_pin_P1 82 102.0 PID 0066 E V
aipid Pin P1/Ct#432 Def: J1587 PID 102=TBS / 0=No Input
tbs_initial_value 84 172.0 A/D 00ac E V
aiinit TBS A/D counts used on system initialization
tbs_timer 86 5.0 SEC 0032 E*10 V
aitval ramp/rst SECS of TBS fault to log code if enabled
tbs_rawhilimit 88 973.0 A/D 03cd E V
aishi TBS A/D counts > rawhilim to log TBS failed high
tbs_rawlolimit 8A 48.0 A/D 0030 E V
aislo TBS A/D counts < rawlolim to log TBS failed low
tbs_default 8C 172.0 A/D 00ac E V
aidfl TBS A/D counts used if TBS failed high OR low
tbs_offset 8E 70.0 A/D 0046 E V
aioff TBS A/D counts OFFSET: kpa=(A/Dfilt+OFFSET)*gain
tbs_gain 90 0.411 K/C 007a U*128 V
aigain TBS kpa/A/Dcount GAIN: kpa=(A/Dfilt+offset)*GAIN
tbs_scaledhilimit 92 1763.7 KPA 0ffc U V
aivhi Boost Press kpa > sclhilim to log Boost Press high
tbs_scaledlolimit 94 0.0 KPA 0000 U V
aivlo Boost Press kpa < scllolim to log Boost Press low
tbs_filterconst 96 0.500 % @ 40 E*128 V
aiifc TBS A/D filter: new=old+filt*(new-old) @ 25msec
tbs_pad_bits 97 0.0 "" 0 E V
padbit tbs_pad_bits
tbs_alt_scaledlo 97.4 0.0 Flg 0 E V
aitvlo BstPressLo Timer: 0=intgrtg dflt/1=local ramp/rst
tbs_alt_scaledhi 97.5 0.0 Flg 0 E V
aitvhi BstPressHi Timer: 0=intgrtg dflt/1=local ramp/rst
tbs_alt_sensorlo 97.6 0.0 Flg 0 E V
aitslo TBS FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
tbs_alt_sensorhi 97.7 1.0 Flg 1 E V
aitshi TBS FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
tbs_percent_weight_en 98 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
tbs_flt_percent_weight 98.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
aux_1_pid_pin_L1 9A 0.0 PID 0000 E V
aipid Pin L1/Ct#904 Def: J1587 PID 108=BARO / 0=No Input
aux_1_initial_value 9C 0.0 A/D 0000 E V
aiinit BARO A/D counts used on system initialization
aux_1_timer 9E 0.0 SEC 0000 E*10 V
aitval ramp/rst SECS of BARO fault to log code if enabled
aux_1_rawhilimit A0 982.0 A/D 03d6 E V
aishi BARO A/D counts > rawhilim to log AX1 failed high
aux_1_rawlolimit A2 0.0 A/D 0000 E V
aislo BARO A/D counts < rawhilim to log AX1 failed low
aux_1_default A4 0.0 A/D 0000 E V
aidfl BARO A/D counts used if AX1 failed high OR low
aux_1_offset A6 0.0 A/D 0000 E V
aioff BARO A/D count OFFSET: kpa=(A/Dflt+OFFSET)*gain
aux_1_gain A8 0.000 K/C 0000 U*128 V
aigain BARO kpa/ADcnt GAIN: kpa=(A/Dflt+offset)*GAIN
aux_1_scaledhilimit AA 0.0 KPA 0000 U V
aivhi BARO kpa > sclhilim to log BARO Pressure high
aux_1_scaledlolimit AC 0.0 KPA 0000 U V
aivlo BARO kpa < scllolim to log BARO Pressure low
aux_1_filterconst AE 0.000 % @ 00 E*128 V
aiifc BARO A/D filter: new=old+filt*(new-old) @ 25msec
aux_1_pad_bits AF 0.0 "" 0 E V
padbit aux_1_pad_bits
aux_1_alt_scaledlo AF.4 0.0 Flg 0 E V
aitvlo BAROPressLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_1_alt_scaledhi AF.5 0.0 Flg 0 E V
aitvhi BAROPressHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_1_alt_sensorlo AF.6 0.0 Flg 0 E V
aitslo BARO FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_1_alt_sensorhi AF.7 0.0 Flg 0 E V
aitshi BARO FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_1_percent_weight_en B0 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
aux_1_flt_percent_weight B0.1 0.0 Perc 00 E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
aux_2_pid_pin_M1 B2 0.0 PID 0000 E V
aipid Pin M1/Ct#905 Def: J1587 PID 94=FPS / 0=No Input
aux_2_initial_value B4 0.0 A/D 0000 E V
aiinit FUEL PRESSURE A/D counts on system initialization
aux_2_timer B6 0.0 SEC 0000 E*10 V
aitval ramp/rst SECS of FPS fault to log code if enabled
aux_2_rawhilimit B8 982.0 A/D 03d6 E V
aishi FPS A/D counts > rawhilim to log FPS failed high
aux_2_rawlolimit BA 0.0 A/D 0000 E V
aislo FPS A/D counts < rawlolim to log FPS failed low
aux_2_default BC 0.0 A/D 0000 E V
aidfl FPS A/D counts used if FPS failed high OR low
aux_2_offset BE 0.0 A/D 0000 E V
aioff FPS A/D count OFFSET: kpa=(A/Dflt+OFFSET)*gain
aux_2_gain C0 0.000 K/C 0000 U*128 V
aigain FPS kpa/ADflt GAIN: kpa=(A/Dflt+offset)*GAIN
aux_2_scaledhilimit C2 0.0 KPA 0000 U V
aivhi FPS kpa > sclhilim to log Fuel Pressure high
aux_2_scaledlolimit C4 0.0 KPA 0000 U V
aivlo FPS kpa < scllolim to log Fuel Pressure low
aux_2_filterconst C6 0.000 % @ 00 E*128 V
aiifc FPS A/D filter: new=old+filt*(new-old) @ 25msec
aux_2_pad_bits C7 0.0 "" 0 E V
padbit aux_2_pad_bits
aux_2_alt_scaledlo C7.4 0.0 Flg 0 E V
aitvlo FuelPressLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_2_alt_scaledhi C7.5 0.0 Flg 0 E V
aitvhi FuelPressHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_2_alt_sensorlo C7.6 0.0 Flg 0 E V
aitslo FPS FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_2_alt_sensorhi C7.7 0.0 Flg 0 E V
aitshi FPS FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_2_percent_weight_en C8 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
aux_2_flt_percent_weight C8.1 0.0 Perc 00 E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
aux_3_pid_pin_N1 CA 0.0 PID 0000 E V
aipid Pin N1/Ct#906 Def: J1587 PID 101=CCPS / 0=No Input
aux_3_initial_value CC 0.0 A/D 0000 E V
aiinit Crk Case Press A/D counts on system initialization
aux_3_timer CE 0.0 SEC 0000 E*10 V
aitval ramp/rst SECS of CCPS fault to log code if enabled
aux_3_rawhilimit D0 982.0 A/D 03d6 E V
aishi CCPS A/D counts > rawhilim to log CCPS failed high
aux_3_rawlolimit D2 0.0 A/D 0000 E V
aislo CCPS A/D counts < rawlolim to log CCPS failed low
aux_3_default D4 0.0 A/D 0000 E V
aidfl CCPS A/D counts used if CCPS failed high OR low
aux_3_offset D6 0.0 A/D 0000 E V
aioff CCPS A/D counts OFFSET: kpa=(A/Dflt+OFFSET)*gain
aux_3_gain D8 0.000 %/C 0000 U*128 V
aigain CCPS %/ADflt GAIN: A/DCnt=(A/Dflt+offset)*GAIN
aux_3_scaledhilimit DA 0.0 %CP 0000 U V
aivhi CCPS % > sclhilim to log Crk Case Press high
aux_3_scaledlolimit DC 0.0 %CP 0000 U V
aivlo CCPS % < scllolim to log Crk Case Press low
aux_3_filterconst DE 0.000 % @ 00 E*128 V
aiifc CCPS A/D filter: new=old+filt*(new-old) @ 25msec
aux_3_pad_bits DF 0.0 "" 0 E V
padbit aux_3_pad_bits
aux_3_alt_scaledlo DF.4 0.0 Flg 0 E V
aitvlo CrkCasePrLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_3_alt_scaledhi DF.5 0.0 Flg 0 E V
aitvhi CrkCasePrHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_3_alt_sensorlo DF.6 0.0 Flg 0 E V
aitslo CCPS FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_3_alt_sensorhi DF.7 0.0 Flg 0 E V
aitshi CCPS FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_3_percent_weight_en E0 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
aux_3_flt_percent_weight E0.1 0.0 Perc 00 E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
aux_4_pid_pin_L2 E2 0.0 PID 0000 E V
aipid Pin L2/Ct#976 Def: J1587 PID 109=CPS / 0=No Input
aux_4_initial_value E4 0.0 A/D 0000 E V
aiinit Coolant Press A/D counts on system initialization
aux_4_timer E6 0.0 SEC 0000 E*10 V
aitval ramp/rst SECS of CPS fault to log code if enabled
aux_4_rawhilimit E8 982.0 A/D 03d6 E V
aishi CPS A/D counts > rawhilim to log CPS failed high
aux_4_rawlolimit EA 0.0 A/D 0000 E V
aislo CPS A/D counts < rawlolim to log CPS failed low
aux_4_default EC 0.0 A/D 0000 E V
aidfl CPS A/D counts uses if CPS failed high OR low
aux_4_offset EE 0.0 A/D 0000 E V
aioff CPS A/D counts OFFSET: kpa=(A/Dflt+OFFSET)*gain
aux_4_gain F0 0.000 K/C 0000 U*128 V
aigain CPS kpa/ADflt GAIN: kpa=(A/Dflt+offset)*GAIN
aux_4_scaledhilimit F2 0.0 KPA 0000 U V
aivhi CPS kpa > sclhilim to log Coolant Pressure high
aux_4_scaledlolimit F4 0.0 KPA 0000 U V
aivlo CPS kpa < scllolim to log Coolant Pressure low
aux_4_filterconst F6 0.000 % @ 00 E*128 V
aiifc CPS A/D filter: new=old+filt*(new-old) @ 25msec
aux_4_pad_bits F7 0.0 "" 0 E V
padbit aux_4_pad_bits
aux_4_alt_scaledlo F7.4 0.0 Flg 0 E V
aitvlo CoolPressLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_4_alt_scaledhi F7.5 0.0 Flg 0 E V
aitvhi CoolPressHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_4_alt_sensorlo F7.6 0.0 Flg 0 E V
aitslo CPS FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_4_alt_sensorhi F7.7 0.0 Flg 0 E V
aitshi CPS FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_4_percent_weight_en F8 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
aux_4_flt_percent_weight F8.1 0.0 Perc 00 E*1.27 V
fltprc Prcnt of deflt time out that procssd valu may frez
aux_5_pid_pin_M2 FA 13.0 PID 000d E V
aipid Pin M2/Ct#958 Def: PID 13=OI Stat / 0=No Input
aux_5_initial_value FC 0.0 A/D 0000 E V
aiinit OI Thermostat A/D counts used on system initlztion
aux_5_timer FE 5.0 SEC 0032 E*10 V
aitval ramp/rst SECS of OI Stat fault for code if enabled
aux_5_rawhilimit 100 1023.0 A/D 03ff E V
aishi OI Stat A/D counts > rawhilim for OLS failed high
aux_5_rawlolimit 102 0.0 A/D 0000 E V
aislo OI Stat A/D counts < rawlolim for OLS failed low
aux_5_default 104 0.0 A/D 0000 E V
aidfl OI Stat A/D counts used if Stat failed high OR low
aux_5_offset 106 512.0 A/D 0200 E V
aioff if OI Stat counts > OFFSET then Stat unsatisfied
aux_5_gain 108 0.000 %/C 0000 U*128 V
aigain OI Stat GAIN not used: EngUnt=(A/Dflt+offset)*GAIN
aux_5_scaledhilimit 10A 1600.0 %LVL 0640 U V
aivhi OI Stat not used: EngUnit>sclhilim for EngUnt high
aux_5_scaledlolimit 10C 0.0 %LVL 0000 U V
aivlo OI Stat not used: EngUnit<scllolim for EngUnit low
aux_5_filterconst 10E 0.102 % @ 0d E*128 V
aiifc OI Stat A/D filter: new=old+filt*(new-old) @25msec
aux_5_pad_bits 10F 0.0 "" 0 E V
padbit aux_5_pad_bits
aux_5_alt_scaledlo 10F.4 0.0 Flg 0 E V
aitvlo ScaledLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_5_alt_scaledhi 10F.5 0.0 Flg 0 E V
aitvhi ScaledHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_5_alt_sensorlo 10F.6 0.0 Flg 0 E V
aitslo FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_5_alt_sensorhi 10F.7 0.0 Flg 0 E V
aitshi FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_5_percent_weight_en 110 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
aux_5_flt_percent_weight 110.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
aux_6_pid_pin_R1 112 171.0 PID 00ab E V
aipid Pin R1/Ct#907 Def: J1587 PID 171=AAT / 0=No Input
aux_6_initial_value 114 430.0 A/D 01ae E V
aiinit Ambient Air Temp A/D cnts on system initialization
aux_6_timer 116 5.0 SEC 0032 E*10 V
aitval ramp/rst SECS of AAT fault to log code if enabled
aux_6_rawhilimit 118 928.0 A/D 03a0 E V
aishi AAT A/D counts>rawhilim to log AAT failed high
aux_6_rawlolimit 11A 48.0 A/D 0030 E V
aislo AAT NOT USED: A/D counts<rawlolim for failed low
aux_6_default 11C 430.0 A/D 01ae E V
aidfl AAT A/D counts used if AAT failed high OR low
aux_6_offset 11E -1009.0 A/D fffffc0f E V
aioff AAT A/D counts OFFSET: degC=(A/D+OFFSET)*GAIN-40
aux_6_gain 120 -0.106 %/C ffffff3c U*128 V
aigain AAT degC/ADflt GAIN: degC=(A/D+OFFSET)*GAIN-40
aux_6_scaledhilimit 122 244.4 %PS 1002 U V
aivhi AAT degC > sclhilim to log AmbAirTemp high
aux_6_scaledlolimit 124 -40.0 %PS 0000 U V
aivlo AAT degC < scllolim to log AmbAirTemp low
aux_6_filterconst 126 0.102 % @ 0d E*128 V
aiifc AAT A/D filter: new=old+filt*(new-old) @ 25msec
aux_6_pad_bits 127 0.0 "" 0 E V
padbit aux_6_pad_bits
aux_6_alt_scaledlo 127.4 0.0 Flg 0 E V
aitvlo AmbAirT low Timer: 0=intgrtg dflt/1=local ramp/rst
aux_6_alt_scaledhi 127.5 0.0 Flg 0 E V
aitvhi AmbAirThigh Timer: 0=intgrtg dflt/1=local ramp/rst
aux_6_alt_sensorlo 127.6 0.0 Flg 0 E V
aitslo AAT FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_6_alt_sensorhi 127.7 0.0 Flg 0 E V
aitshi AAT FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_6_percent_weight_en 128 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
aux_6_flt_percent_weight 128.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
aux_7_pid_pin_D3 12A 0.0 PID 0000 E V
aipid Pin D3/Ct#749 Def: J1587 PID 73=FTWP / 0=No Input
aux_7_initial_value 12C 0.0 A/D 0000 E V
aiinit FireTrkWaterPres A/D cnts on system initialization
aux_7_timer 12E 0.0 SEC 0000 E*10 V
aitval ramp/rst SECS of FTWP fault to log code if enabled
aux_7_rawhilimit 130 982.0 A/D 03d6 E V
aishi FTWP A/D counts > rawhilim to log FTWP failed high
aux_7_rawlolimit 132 0.0 A/D 0000 E V
aislo FTWP A/D counts < rawlolim to log FTWP failed low
aux_7_default 134 0.0 A/D 0000 E V
aidfl FTWP A/D counts used if FTWP failed high OR low
aux_7_offset 136 0.0 A/D 0000 E V
aioff FTWP A/D counts OFFSET: psi=(A/Dflt+OFFSET)*gain
aux_7_gain 138 0.000 P/C 0000 U*128 V
aigain FTWP psi/ADflt GAIN: psi=(A/Dflt+offset)*GAIN
aux_7_scaledhilimit 13A 0.0 PSI 0000 U V
aivhi FTWaterPress psi > sclhilim to log FTWtrPress high
aux_7_scaledlolimit 13C 0.0 PSI 0000 U V
aivlo FTWaterPress psi < scllolim to log FTWtrPress low
aux_7_filterconst 13E 0.000 % @ 00 E*128 V
aiifc FTWP A/D filter: new=old+filt*(new-old) @ 25msec
aux_7_pad_bits 13F 0.0 "" 0 E V
padbit aux_7_pad_bits
aux_7_alt_scaledlo 13F.4 0.0 Flg 0 E V
aitvlo FTWtrPresLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_7_alt_scaledhi 13F.5 0.0 Flg 0 E V
aitvhi FTWtrPresHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_7_alt_sensorlo 13F.6 0.0 Flg 0 E V
aitslo FTWP FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
aux_7_alt_sensorhi 13F.7 0.0 Flg 0 E V
aitshi FTWP FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
aux_7_percent_weight_en 140 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
aux_7_flt_percent_weight 140.1 0.0 Perc 00 E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
tps_pid_pin_D2 142 91.0 PID 005b E V
aipid Pin D2/Ct#417 Def: J1587 PID 91=%TPS / 0=No Input
tps_initial_value 144 968.0 A/D 03c8 E V
aiinit TPS A/D counts used on system initialization
tps_timer 146 0.2 SEC 0002 E*10 V
aitval ramp/rst SECS of TPS fault to log code if enabled
tps_rawhilimit 148 968.0 A/D 03c8 E V
aishi TPS A/D counts > rawhilim to log TPS failed high
tps_rawlolimit 14A 48.0 A/D 0030 E E
aislo TPS A/D counts < rawlolim to log TPS failed low
tps_default 14C 0.0 A/D 0000 E V
aidfl TPS A/D counts used if TPS failed high OR low
tps_offset 14E 968.0 N/A 03c8 E V
aioff Not Used: calcd OFFSET = min(A/Dfilt) + tpohis
tps_gain 150 0.202 %TPS 0042 U*128 V
aigain %TPS/ADflt GAIN: %TPS=(A/Dflt-calcd OFFSET)*GAIN
tps_scaledhilimit 152 99.7 %TPS 00ff U V
aivhi %TPS > sclhilim to log %TPS high
tps_scaledlolimit 154 0.0 %TPS 0000 U V
aivlo %TPS < scllolim to log %TPS low
tps_filterconst 156 0.500 % @ 40 E*128 V
aiifc TPS A/Dflt: new=old+filt*(new-old) @ 25msec
tps_pad_bits 157 0.0 "" 0 E V
padbit tps_pad_bits
tps_alt_scaledlo 157.4 0.0 Flg 0 E V
aitvlo %TPS Low Timer: 0=intgrtg dflt/1=local ramp/reset
tps_alt_scaledhi 157.5 0.0 Flg 0 E V
aitvhi %TPS High Timer: 0=intgrtg dflt/1=local ramp/rst
tps_alt_sensorlo 157.6 1.0 Flg 1 E V
aitslo TPS FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
tps_alt_sensorhi 157.7 1.0 Flg 1 E V
aitshi TPS FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
tps_percent_weight_en 158 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
tps_flt_percent_weight 158.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
pto_pid_pin_D1 15A 187.0 PID 00bb E E
aipid Pin D1/Ct#510 Def:J1587 PID 187=PTO RPM/0=No Input
pto_initial_value 15C 206.0 A/D 00ce E V
aiinit PTO A/D counts used on system initialization
pto_timer 15E 2.0 SEC 0014 E*10 V
aitval ramp/rst SECS of PTO fault to log code if enabled
pto_rawhilimit 160 968.0 A/D 03c8 E V
aishi PTO A/D counts > rawhilim to log PTO failed high
pto_rawlolimit 162 0.0 A/D 0000 E E
aislo PTO A/D counts < rawlolim to log PTO failed low
pto_default 164 0.0 A/D 0000 E V
aidfl PTO A/D counts used if PTO failed high OR low
pto_offset 166 -140.0 A/D ffffff74 E E
aioff PTO A/Dfilt=max(0, hystsis(impls(A/Draw))+OFFSET)
pto_gain 168 0.000 RPM 0000 U*128 V
aigain Not Used-SW calc: PTO GAIN=(ptmaxv-ptminv)/ptodiv
pto_scaledhilimit 16A 4095.8 RPM 3fff U V
aivhi PTO RPM > sclhilim to log PTO RPM high
pto_scaledlolimit 16C 0.0 RPM 0000 U V
aivlo PTO RPM < scllolim to log PTO RPM low
pto_filterconst 16E 0.250 % @ 20 E*128 V
aiifc PTO A/D filter: new=old+filt*(new-old) @ 25msec
pto_pad_bits 16F 0.0 "" 0 E V
padbit pto_pad_bits
pto_alt_scaledlo 16F.4 0.0 Flg 0 E V
aitvlo PTO RPM Lo Timer: 0=intgrtg dflt/1=local ramp/rst
pto_alt_scaledhi 16F.5 0.0 Flg 0 E V
aitvhi PTO RPM Hi Timer: 0=intgrtg dflt/1=local ramp/rst
pto_alt_sensorlo 16F.6 0.0 Flg 0 E V
aitslo PTO FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
pto_alt_sensorhi 16F.7 0.0 Flg 0 E V
aitshi PTO FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
pto_percent_weight_en 170 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
pto_flt_percent_weight 170.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
cls_pid_pin_H3 172 111.0 PID 006f E V
aipid Pin H3/Ct#115 Def: J1587 PID 111=%CLS/0=No Input
cls_initial_value 174 102.0 A/D 0066 E V
aiinit CLS A/D counts used on system initialization
cls_timer 176 15.0 SEC 0096 E*10 V
aitval ramp/rst SECS of CLS fault to log code if enabled
cls_rawhilimit 178 948.0 A/D 03b4 E V
aishi CLS A/D counts > rawhilim to log CLS failed high
cls_rawlolimit 17A 0.0 A/D 0000 E V
aislo CLS A/D counts < rawlolim to log CLS failed low
cls_default 17C 102.0 A/D 0066 E V
aidfl CLS A/D counts used if CLS failed high OR low
cls_offset 17E -1024.0 A/D fffffc00 E V
aioff CLS A/D counts OFFSET: %CLS=(A/Dfilt+OFFSET)*gain
cls_gain 180 -0.098 %/C ffffffe7 U*128 V
aigain %CLS/ADfilt GAIN: %CLS=(A/Dfilt+offset)*GAIN
cls_scaledhilimit 182 100.0 %CLS 00c8 U V
aivhi %CLS > sclhilim to log Coolant Level high
cls_scaledlolimit 184 30.0 %CLS 003c U V
aivlo CLS %lolvl OFFSET: %lolvl=scldlolim+cllmgn*radtemp
cls_filterconst 186 0.102 % @ 0d E*128 V
aiifc CLS A/D filter: new=old+filt*(new-old) @ 25msec
cls_pad_bits 187 0.0 "" 0 E V
padbit cls_pad_bits
cls_alt_scaledlo 187.4 1.0 Flg 1 E V
aitvlo %CLS Low Timer: 0=intgrtg dflt/1=local ramp/rst
cls_alt_scaledhi 187.5 0.0 Flg 0 E V
aitvhi %CLS High Timer: 0=intgrtg dflt/1=local ramp/rst
cls_alt_sensorlo 187.6 0.0 Flg 0 E V
aitslo CLS FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
cls_alt_sensorhi 187.7 0.0 Flg 0 E V
aitshi CLS FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
cls_percent_weight_en 188 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
cls_flt_percent_weight 188.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
mbv_pid 18A 168.0 PID 00a8 E V
aipid J1587 PID 168=Batt Volts Xmitted / 0=Not Xmitted
mbv_initial_value 18C 242.0 A/D 00f2 E V
aiinit Main Battery Volts A/D counts used on system init
mbv_timer 18E 30.0 SEC 012c E*10 V
aitval ramp/rst SECS of MBV fault to log code if enabled
mbv_rawhilimit 190 1023.0 A/D 03ff E V
aishi MBV A/D counts > rawhilim to log MBV failed high
mbv_rawlolimit 192 0.0 A/D 0000 E V
aislo MBV A/D counts < rawlolim to log MBV failed low
mbv_default 194 261.0 A/D 0105 E V
aidfl MBV A/D counts used if MBV failed high OR low
mbv_offset 196 0.0 A/D 0000 E V
aioff MBV A/D counts OFFSET: volts=(A/Dflt+OFFSET)*gain
mbv_gain 198 0.054 V/C 044c U*128 V
aigain MBV volts/ADflt GAIN: volts=(A/Dflt+offset)*GAIN
mbv_scaledhilimit 19A 48.0 VLT 1e00 U V
aivhi MBV volts > sclhilim to log MBV volts high
mbv_scaledlolimit 19C 10.0 VLT 0640 U V
aivlo MBV volts < scllolim to log MBV volts low
mbv_filterconst 19E 0.008 % @ 01 E*128 V
aiifc MBV A/D filter: new=old+filt*(new-old) @ 25msec
mbv_pad_bits 19F 0.0 "" 0 E V
padbit mbv_pad_bits
mbv_alt_scaledlo 19F.4 1.0 Flg 1 E V
aitvlo MBVVoltsLo Timer: 0=intgrtg dflt/1=local ramp/rst
mbv_alt_scaledhi 19F.5 0.0 Flg 0 E V
aitvhi MBVVoltsHi Timer: 0=intgrtg dflt/1=local ramp/rst
mbv_alt_sensorlo 19F.6 0.0 Flg 0 E V
aitslo MBV FailLo Timer: 0=intgrtg dflt/1=local ramp/rst
mbv_alt_sensorhi 19F.7 0.0 Flg 0 E V
aitshi MBV FailHi Timer: 0=intgrtg dflt/1=local ramp/rst
mbv_percent_weight_en 1A0 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
mbv_flt_percent_weight 1A0.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
rbb_pid 1A2 17.0 PID 0011 E V
aipid PID
rbb_initial_value 1A4 737.0 Coun 02e1 E V
aiinit RTC battery volts A/D counts used on sys init.
rbb_timer 1A6 5.0 Sec. 0032 E*10 V
aitval ramp/rst SECS of RTC fault to log code if enabled
rbb_rawhilimit 1A8 1023.0 Coun 03ff E V
aishi RTC A/D counts > rawhilim to log RTC failed high
rbb_rawlolimit 1AA 0.0 Coun 0000 E V
aislo RTC A/D counts < rawlolim to log RTC failed low
rbb_default 1AC 737.0 Coun 02e1 E V
aidfl RTC A/D counts used if RTC failed high or low
rbb_offset 1AE 0.0 Coun 0000 E V
aioff RTC A/D counts OFFSET: volts*(A/Dflt+OFFSET)*gain
rbb_gain 1B0 0.005 V/C 0064 U*128 V
aigain RTC volts/ADflt GAIN: volts=(A/Dflt+offset)*GAIN
rbb_scaledhilimit 1B2 12.8 Volt 07ff U V
aivhi RTC volts > sclhilim to log RTC volts high
rbb_scaledlolimit 1B4 0.0 Volt 0000 U V
aivlo RTC volts < scllolim to log RTC volts low
rbb_filterconst 1B6 0.102 % @ 0d E*128 V
aiifc RTC A/D filter: new=old+filt*(new-old) @ 25mSec
rbb_pad_bits 1B7 0.0 "" 0 E V
padbit rbb_pad_bits
rbb_alt_scaledlo 1B7.4 1.0 Flg 1 E V
aitvlo RTCvolts lo timer: 0=intfrtg dflt/1=local ramp/rst
rbb_alt_scaledhi 1B7.5 1.0 Flg 1 E V
aitvhi RTCvoltshi timer: 0=intgrtg dflt/1=local ramp/rst
rbb_alt_sensorlo 1B7.6 0.0 Flg 0 E V
aitslo RTC fail lo timer: 0=intgrtg dflt/1=local ramp/rst
rbb_alt_sensorhi 1B7.7 0.0 Flg 0 E V
aitshi RTC fail hi timer: 0=intgrtg dflt/1=local ramp/rst
rbb_percent_weight_en 1B8 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
rbb_flt_percent_weight 1B8.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez
ssv_pid 1BA 1.0 PID 0001 E V
aipid J1587 PID
ssv_initial_value 1BC 512.0 Coun 0200 E V
aiinit SSV battery volts A/D counts used on sys init.
ssv_timer 1BE 1.0 Seco 000a E*10 V
aitval ramp/rst SECS of SSV fault to log code if enabled
ssv_rawhilimit 1C0 1023.0 Coun 03ff E V
aishi SSV A/D counts > rawhilim to log SSV failed high
ssv_rawlolimit 1C2 0.0 Coun 0000 E V
aislo SSV A/D counts < rawlolim to log SSV failed low
ssv_default 1C4 512.0 Coun 0200 E V
aidfl SSV A/D counts used if SSV failed high or low
ssv_offset 1C6 0.0 Coun 0000 E V
aioff SSV A/D counts OFFSET: volts*(A/Dflt+OFFSET)*gain
ssv_gain 1C8 0.007 V/C 0091 U*128 V
aigain SSV volts/ADflt GAIN: volts=(A/Dflt+offset)*GAIN
ssv_scaledhilimit 1CA 5.7 Volt 0390 U V
aivhi SSV volts > sclhilim to log SSV volts high
ssv_scaledlolimit 1CC 4.3 Volt 02b0 U V
aivlo SSV volts < scllolim to log SSV volts low
ssv_filterconst 1CE 0.500 % @ 40 E*128 V
aiifc SSV A/D filter: new=old+filt*(new-old) @ 25mSec
ssv_pad_bits 1CF 0.0 "" 0 E V
padbit ssv_pad_bits
ssv_alt_scaledlo 1CF.4 1.0 Flg 1 E V
aitvlo SSVvolts lo timer: 0=intfrtg dflt/1=local ramp/rst
ssv_alt_scaledhi 1CF.5 1.0 Flg 1 E V
aitvhi SSVvoltshi timer: 0=intgrtg dflt/1=local ramp/rst
ssv_alt_sensorlo 1CF.6 0.0 Flg 0 E V
aitslo SSV fail lo timer: 0=intgrtg dflt/1=local ramp/rst
ssv_alt_sensorhi 1CF.7 0.0 Flg 0 E V
aitshi SSV fail hi timer: 0=intgrtg dflt/1=local ramp/rst
ssv_percent_weight_en 1D0 0.0 Flg 0 E V
fprcfg If set, anlg intrmttnt flt filtering is activated
ssv_flt_percent_weight 1D0.1 100.0 Perc 7f E*1.27 B
fltprc Prcnt of deflt time out that procssd valu may frez

NAME: inj_cal_chng_1_tool_id ADDR: 1D2 UNT: ID OWN: S CODE: toolid


EQN: E
ID of Tool which made last INJCAL change - 8 Bytes
Elements| HEX| ID
--------------------------------
1| 00| 0.0
2| 00| 0.0
3| 00| 0.0
4| 00| 0.0
5| 00| 0.0
6| 00| 0.0
7| 00| 0.0
8| 00| 0.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
inj_cal_chng_1_engine_hours 1DA 0.00000 Hr 00000000 E*3600 S
enghrs Engine Hours () of last INJCAL change -1sec/bit
inj_cal_chng_1_seconds 1DE 0.00 Sec 00 E*4 S
second Seconds (0-59.75) of last INJCAL change-.25sec/bit
inj_cal_chng_1_minutes 1DF 0.0 Min 00 E S
minute Minutes (0-59) of last INJCAL change - 1min/bit
inj_cal_chng_1_hours 1E0 0.0 Hr 00 E S
hour Hours (0-23) of last INJCAL change - 1hour/bit
inj_cal_chng_1_day 1E1 1.0 Day 00 E-1.000000 S
day Date (1-31) of last INJCAL change - 1day/bit
inj_cal_chng_1_month 1E2 1.0 Mont 00 E-1.000000 S
month Month (1-12) of last INJCAL change - 1month/bit
inj_cal_chng_1_year 1E3 1985.0 Yr 00 E-1985.000000 S
year Year (1985-2084) of last INJCAL change - 1year/bit

NAME: inj_cal_chng_2_tool_id ADDR: 1E4 UNT: ID OWN: S CODE: toolid


EQN: E
ID of Tool which made 2nd lst INJCAL change-8 Byte
Elements| HEX| ID
--------------------------------
1| 00| 0.0
2| 00| 0.0
3| 00| 0.0
4| 00| 0.0
5| 00| 0.0
6| 00| 0.0
7| 00| 0.0
8| 00| 0.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
inj_cal_chng_2_engine_hours 1EC 0.00000 Hr 00000000 E*3600 S
enghrs Engine Hours () of 2nd lst INJCAL chng-1sec/bit
inj_cal_chng_2_seconds 1F0 0.00 Sec 00 E*4 S
second Seconds (0-59.75) of 2nd lst INJCAL chng-.25sec/bt
inj_cal_chng_2_minutes 1F1 0.0 Min 00 E S
minute Minutes (0-59) of 2nd lst INJCAL change - 1min/bit
inj_cal_chng_2_hours 1F2 0.0 Hr 00 E S
hour Hours (0-23) of 2nd last INJCAL change - 1hour/bit
inj_cal_chng_2_day 1F3 1.0 Day 00 E-1.000000 S
day Date (1-31) of 2nd last INJCAL change - 1day/bit
inj_cal_chng_2_month 1F4 1.0 Mont 00 E-1.000000 S
month Month (1-12) of 2nd last INJCAL change -1month/bit
inj_cal_chng_2_year 1F5 1985.0 Yr 00 E-1985.000000 S
year Year (1985-2084) of 2nd last INJCAL change-1yr/bit
NAME: inj_cal_chng_3_tool_id ADDR: 1F6 UNT: ID OWN: S CODE: toolid
EQN: E
ID of Tool which made 3rd lst INJCAL change-8 Byte
Elements| HEX| ID
--------------------------------
1| 00| 0.0
2| 00| 0.0
3| 00| 0.0
4| 00| 0.0
5| 00| 0.0
6| 00| 0.0
7| 00| 0.0
8| 00| 0.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
inj_cal_chng_3_engine_hours 1FE 0.00000 Hr 00000000 E*3600 S
enghrs Engine Hours () of 3rd lst INJCAL chng-1sec/bit
inj_cal_chng_3_seconds 202 0.00 Sec 00 E*4 S
second Seconds (0-59.75) of 3rd lst INJCAL chng-.25sec/bt
inj_cal_chng_3_minutes 203 0.0 Min 00 E S
minute Minutes (0-59) of 3rd last INJCAL change- 1min/bit
inj_cal_chng_3_hours 204 0.0 Hr 00 E S
hour Hours (0-23) of 3rd last INJCAL change - 1hour/bit
inj_cal_chng_3_day 205 1.0 Day 00 E-1.000000 S
day Date (1-31) of 3rd last INJCAL change - 1day/bit
inj_cal_chng_3_month 206 1.0 Mont 00 E-1.000000 S
month Month (1-12) of 3rd last INJCAL change- 1month/bit
inj_cal_chng_3_year 207 1985.0 Yr 00 E-1985.000000 S
year Year (1985-2084) of 3rd last INJCAL change-1yr/bit
pw_frequency_1 208 50.0 Hz 0032 E E
pwfrq PWM1 frequency in Hz
pw_controlvalue_1 20A 0 = channel unassigned, output always high0 =
channel unassigned, output always high O pwsrc PWM1: output function
0=None,1=BlwrByp,2=GloPlg,
pw_lolimit_1 20B 0.0 %DC 00 E O
pwllo PWM:min duty cycle / DSCRT:cntrlval>pwllo then ON
pw_hilimit_1 20C 0.0 %DC 00 E O
pwlup PWM:max duty cycle / DSCRT:cntrlval<lo-up then OFF
pw_dotruncate_1 20D.3 0.0 Flg 0 E O
pwscl PWM1: 0=control val scaled lo to up / 1=truncate
pw_dothreshold_1 20D.4 0.0 Flg 0 E O
pwthr PWM1: 0=PWM mode / 1=DiSCReTe (on/off) mode
pw_reverse_1 20D.5 0.0 Flg 0 E O
pwrev PWM1: 0=enabled low / 1=enabled high
pw_passive_diagnostic_enable_1 20D.6 0.0 Flg 0 E O
pwpde PWM1: set for stuck low diagnostics - load req'd
pw_active_diagnostic_enable_1 20D.7 0.0 Flg 0 E E
pwade PWM1: set for stuck high diagnostics
pw_frequency_2 20E 50.0 Hz 0032 E E
pwfrq PWM2 frequency in Hz
pw_controlvalue_2 210 0 = channel unassigned, output always high0 =
channel unassigned, output always high E pwsrc PWM2: 3=
%TPS,4=FTQ,5=PwrTrDmd,6=Fan,7=DVB,8=NGfuel
pw_lolimit_2 211 0.0 %DC 00 E E
pwllo PWM:min duty cycle / DSCRT:cntrlval>pwllo then ON
pw_hilimit_2 212 0.0 %DC 00 E E
pwlup PWM:max duty cycle / DSCRT:cntrlval<lo-up then OFF
pw_dotruncate_2 213.3 0.0 Flg 0 E E
pwscl PWM2: 0=control val scaled lo to up / 1=truncate
pw_dothreshold_2 213.4 0.0 Flg 0 E E
pwthr PWM2: 0=PWM mode / 1=DisCReTe (on/off) mode
pw_reverse_2 213.5 0.0 Flg 0 E E
pwrev PWM2: 0=enabled low / 1=enabled high
pw_passive_diagnostic_enable_2 213.6 0.0 Flg 0 E E
pwpde PWM2: set for stuck low diagnostics - load req'd
pw_active_diagnostic_enable_2 213.7 0.0 Flg 0 E E
pwade PWM2: set for stuck high diagnostics
pw_frequency_3 214 50.0 Hz 0032 E E
pwfrq PWM3 frequency in Hz
pw_controlvalue_3 216 0 = channel unassigned, output always high0 =
channel unassigned, output always high E pwsrc PWM3:
9=NGthrottle,10=OIstrRly,11=OIalarm,12=HPP
pw_lolimit_3 217 0.0 %DC 00 E E
pwllo PWM:min duty cycle / DSCRT:cntrlval>pwllo then ON
pw_hilimit_3 218 0.0 %DC 00 E E
pwlup PWM:max duty cycle / DSCRT:cntrlval<lo-up then OFF
pw_dotruncate_3 219.3 0.0 Flg 0 E E
pwscl PWM3: 0=control val scaled lo to up / 1=truncate
pw_dothreshold_3 219.4 0.0 Flg 0 E E
pwthr PWM3: 0=PWM mode / 1=DisCReTe (on/off) mode
pw_reverse_3 219.5 0.0 Flg 0 E E
pwrev PWM3: 0=enabled low / 1=enabled high
pw_passive_diagnostic_enable_3 219.6 0.0 Flg 0 E E
pwpde PWM3: set for stuck low diagnostics - load req'd
pw_active_diagnostic_enable_3 219.7 0.0 Flg 0 E E
pwade PWM3: set for stuck high diagnostics
pw_frequency_4 21A 10.0 Hz 000a E E
pwfrq PWM4 frequency in Hz
pw_controlvalue_4 21C 6 = fan clutch control function6 = fan clutch
control function E pwsrc PWM4: output function >12=None
pw_lolimit_4 21D 5.0 %DC 05 E E
pwllo PWM:min duty cycle / DSCRT:cntrlval>pwllo then ON
pw_hilimit_4 21E 80.0 %DC 50 E E
pwlup PWM:max duty cycle / DSCRT:cntrlval<lo-up then OFF
pw_dotruncate_4 21F.3 1.0 Flg 1 E E
pwscl PWM4: 0=control val scaled lo to up / 1=truncate
pw_dothreshold_4 21F.4 0.0 Flg 0 E E
pwthr PWM4: 0=PWM mode / 1=DiSCReTe (on/off) mode
pw_reverse_4 21F.5 1.0 Flg 1 E E
pwrev PWM4: 0=enabled low / 1=enabled high
pw_passive_diagnostic_enable_4 21F.6 0.0 Flg 0 E E
pwpde PWM4: set for stuck low diagnostics - load req'd
pw_active_diagnostic_enable_4 21F.7 1.0 Flg 1 E E
pwade PWM4: set for stuck high diagnostics
c_fireangle_1 220.2 0.0 DEG 000 E*2 V
tdcang #1: crank degs between #1CYL firing TDC & #1TRS
c_injector_number_1 221.5 0.0 Flg 0 E V
pinnum #1: assigns each CYL to an INJ pin by firing order
c_fireangle_2 222.2 120.0 DEG 0f0 E*2 V
tdcang #2: crank degs between #2CYL firing TDC & #1TRS
c_injector_number_2 223.5 1.0 Flg 1 E V
pinnum #2: INJ pin definition: 0=#611=pin L 1=#612=pin A
c_fireangle_3 224.2 240.0 DEG 1e0 E*2 V
tdcang #3: crank degs between #3CYL firing TDC & #1TRS
c_injector_number_3 225.5 2.0 Flg 2 E V
pinnum #3: INJ pin definition: 2=#613=pin K 3=#614=pin B
c_fireangle_4 226.2 360.0 DEG 2d0 E*2 V
tdcang #4: crank degs between #4CYL firing TDC & #1TRS
c_injector_number_4 227.5 3.0 Flg 3 E V
pinnum #4: INJ pin definition: 4=#615=pin H 5=#616=pin D
c_fireangle_5 228.2 480.0 DEG 3c0 E*2 V
tdcang #5: crank degs between #5CYL firing TDC & #1TRS
c_injector_number_5 229.5 4.0 Flg 4 E V
pinnum #5: INJ pin definition: 6=#617=pin J 7=#618=pin C
c_fireangle_6 22A.2 600.0 DEG 4b0 E*2 V
tdcang #6: crank degs between #6CYL firing TDC & #1TRS
c_injector_number_6 22B.5 5.0 Flg 5 E V
pinnum #6: assigns each CYL to an INJ pin by firing order
c_fireangle_7 22C.2 0.0 DEG 000 E*2 V
tdcang #7: crank degs between #7CYL firing TDC & #1TRS
c_injector_number_7 22D.5 0.0 Flg 0 E V
pinnum #7: assigns each CYL to an INJ pin by firing order
c_fireangle_8 22E.2 0.0 DEG 000 E*2 V
tdcang #8: crank degs between #8CYL firing TDC & #1TRS
c_injector_number_8 22F.5 0.0 Flg 0 E V
pinnum #8: assigns each CYL to an INJ pin by firing order

NAME: cust_cal_chng_1_tool_id ADDR: 230 UNT: ID OWN: S CODE: toolid


EQN: E
ID of Tool which made last CAL Prog change-8 Bytes
Elements| HEX| ID
--------------------------------
1| 44| 68.0
2| 4d| 77.0
3| 4a| 74.0
4| 4d| 77.0
5| 31| 49.0
6| 37| 55.0
7| 4b| 75.0
8| 4c| 76.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
cust_cal_chng_1_engine_hours 238 1501.15028 Hr 005275ed E*3600 S
enghrs Engine Hours () of last CAL Prog change
cust_cal_chng_1_seconds 23C 50.00 Sec c8 E*4 S
second Seconds (0-59) of last CAL Prog change- .25sec/bit
cust_cal_chng_1_minutes 23D 39.0 Min 27 E S
minute Minutes (0-59) of last CAL Prog change - 1 min/bit
cust_cal_chng_1_hours 23E 19.0 Hr 13 E S
hour Hours (0-23) of last CAL Prog change - 1 hour/bit
cust_cal_chng_1_day 23F 1.0 Day 00 E-1.000000 S
day Date (1-31) of last CAL Prog change - 1 day/bit
cust_cal_chng_1_month 240 10.0 Mont 09 E-1.000000 S
month Month (1-12) of last CAL Prog change - 1 month/bit
cust_cal_chng_1_year 241 2001.0 Yr 10 E-1985.000000 S
year Year (1985-2084) of last CAL Prog change - 1Yr/bit

NAME: cust_cal_chng_2_tool_id ADDR: 242 UNT: ID OWN: S CODE: toolid


EQN: E
ID of Tool which made 2nd to last CAL Prog change
Elements| HEX| ID
--------------------------------
1| 44| 68.0
2| 4d| 77.0
3| 52| 82.0
4| 37| 55.0
5| 46| 70.0
6| 5a| 90.0
7| 35| 53.0
8| 30| 48.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
cust_cal_chng_2_engine_hours 24A 1176.07111 Hr 00409a80 E*3600 S
enghrs Engine Hours () of 2nd to last CAL Prog change
cust_cal_chng_2_seconds 24E 43.50 Sec ae E*4 S
second Seconds (0-59) of 2lst CAL Prog change- .25sec/bit
cust_cal_chng_2_minutes 24F 42.0 Min 2a E S
minute Minutes (0-59) of 2lst CAL Prog change - 1 min/bit
cust_cal_chng_2_hours 250 0.0 Hr 00 E S
hour Hours (0-23) of 2lst CAL Prog change - 1 hour/bit
cust_cal_chng_2_day 251 13.0 Day 0c E-1.000000 S
day Date (1-31) of 2lst CAL Prog change - 1 day/bit
cust_cal_chng_2_month 252 7.0 Mont 06 E-1.000000 S
month Month (1-12) of 2lst CAL Prog change - 1 month/bit
cust_cal_chng_2_year 253 2001.0 Yr 10 E-1985.000000 S
year Year (1985-2084) of 2lst CAL Prog change - 1Yr/bit

NAME: cust_cal_chng_3_tool_id ADDR: 254 UNT: ID OWN: S CODE: toolid


EQN: E
ID of Tool which made 3lst CAL Prog change-8 Bytes
Elements| HEX| ID
--------------------------------
1| 44| 68.0
2| 52| 82.0
3| 53| 83.0
4| 45| 69.0
5| 30| 48.0
6| 38| 56.0
7| 38| 56.0
8| 38| 56.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
cust_cal_chng_3_engine_hours 25C 0.00000 Hr 00000000 E*3600 S
enghrs Engine Hours () of 3lst CAL Prog change
cust_cal_chng_3_seconds 260 44.00 Sec b0 E*4 S
second Seconds (0-59) of 3lst CAL Prog change- .25sec/bit
cust_cal_chng_3_minutes 261 45.0 Min 2d E S
minute Minutes (0-59) of 3lst CAL Prog change - 1 min/bit
cust_cal_chng_3_hours 262 0.0 Hr 00 E S
hour Hours (0-23) of 3lst CAL Prog change - 1 hour/bit
cust_cal_chng_3_day 263 256.0 Day ff E-1.000000 S
day Date (1-31) of 3lst CAL Prog change - 1 day/bit
cust_cal_chng_3_month 264 256.0 Mont ff E-1.000000 S
month Month (1-12) of 3lst CAL Prog change - 1 month/bit
cust_cal_chng_3_year 265 2000.0 Yr 0f E-1985.000000 S
year Year (1985-2084) of 3lst CAL Prog change - 1Yr/bit
rsl_chng_1_seconds 266 44.50 Sec b2 E*4 S
second Seconds (0-59) of most recent RSL chng-.25sec/bit
rsl_chng_1_minutes 267 45.0 Min 2d E S
minute Minutes (0-59) of most recent RSL chng-1 min/bit
rsl_chng_1_hours 268 0.0 Hour 00 E S
hour Hours (0-23) of most recent RSL chng-1 hour/bit
rsl_chng_1_day 269 256.0 Day ff E-1.000000 S
day Date (1-31) of most recent RSL chg-1 day/bit
rsl_chng_1_month 26A 256.0 Mont ff E-1.000000 S
month Month (1-12) of most recent RSL chg- 1 month/bit
rsl_chng_1_year 26B 2000.0 Year 0f E-1985.000000 S
year Year (1985-2084) of most recent RSL chg-1Yr/bit
rsl_chng_1_engine_hours 26C 0.00000 Hour 00000000 E*3600 S
enghrs Engine Hours () most recent RSL change
rsl_chng_1_rsl_change_status 270 194.0 "" 00c2 E S
rslchg Status word for RSL paramters
rsl_chng_1_tool_id 272 "DRSE0888" S
toolid ID of Tool whch md most recent Prog change-8 Bytes
rsl_chng_2_seconds 27A 0.00 Sec 00 E*4 S
second Seconds (0-59) of 2nd RSL Prog change- .25sec/bit
rsl_chng_2_minutes 27B 0.0 Min 00 E S
minute Minutes (0-59) of 2nd RSL Prog change - 1 min/bit
rsl_chng_2_hours 27C 0.0 Hour 00 E S
hour Hours (0-23) of 2nd RSL Prog change - 1 hour/bit
rsl_chng_2_day 27D 1.0 Days 00 E-1.000000 S
day Date (1-31) of 2nd RSL Prog change - 1 day/bit
rsl_chng_2_month 27E 1.0 Mont 00 E-1.000000 S
month Month (1-12) of 2nd RSL Prog change - 1 month/bit
rsl_chng_2_year 27F 1985.0 Year 00 E-1985.000000 S
year Year (1985-2084) of 2nd RSL Prog change - 1Yr/bit
rsl_chng_2_engine_hours 280 0.00000 Hour 00000000 E*3600 S
enghrs Engine Hours () of 2nd RSL Prog change
rsl_chng_2_rsl_change_status 284 0.0 "" 0000 E S
rslchg rsl_chng_2_rsl_change_status
rsl_chng_2_tool_id 286 " " S
toolid ID of Tool whch md most recent Prog change-8 Bytes
rsl_chng_3_seconds 28E 0.00 Sec 00 E*4 S
second Seconds (0-59) of 3rd RSL Prog change- .25sec/bit
rsl_chng_3_minutes 28F 0.0 Minu 00 E S
minute Minutes (0-59) of 3rd RSL Prog change - 1 min/bit
rsl_chng_3_hours 290 0.0 Hour 00 E S
hour Hours (0-23) of 3rd RSL Prog change - 1 hour/bit
rsl_chng_3_day 291 1.0 Days 00 E-1.000000 S
day Date (1-31) of 3rd RSL Prog change - 1 day/bit
rsl_chng_3_month 292 1.0 Mont 00 E-1.000000 S
month Month (1-12) of 3rd RSL Prog change - 1 month/bit
rsl_chng_3_year 293 1985.0 Year 00 E-1985.000000 S
year Year (1985-2084) of 3rd RSL Prog change - 1Yr/bit
rsl_chng_3_engine_hours 294 0.00000 Hour 00000000 E*3600 S
enghrs Engine Hours () of 3rd RSL Prog change
rsl_chng_3_rsl_change_status 298 0.0 "" 0000 E S
rslchg rsl_chng_3_rsl_change_status
rsl_chng_3_tool_id 29A " " S
toolid ID of Tool whch md most recent Prog change-8 Bytes
spare_1_1 2A2 0.0 "" 0000 E V
spare1 Spare calibration
spare_1_2 2A4 0.0 "" 0000 E V
spare1 Spare calibration
spare_2_1 2A6 0.0 "" 0000 E V
spare2 Spare calibration
spare_2_2 2A8 0.0 "" 0000 E V
spare2 Spare calibration
spare_3_1 2AA 0.0 "" 0000 E*2 V
spare3 Spare calibration
spare_3_2 2AC 5.0 "" 000a E*2 V
spare3 Spare calibration
spare_4_1 2AE 0.0 "" 0000 E*2 V
spare4 Spare calibration
spare_4_2 2B0 0.0 "" 0000 E*2 V
spare4 Spare calibration
spare_5_1 2B2 0.00 "" 0000 E*4 V
spare5 Spare calibration
spare_5_2 2B4 0.00 "" 0000 E*4 V
spare5 Spare calibration
spare_6_1 2B6 0.00 "" 0000 E*4 V
spare6 Spare calibration
spare_6_2 2B8 0.00 "" 0000 E*4 V
spare6 Spare calibration
spare_7_1 2BA 0.00 "" 0000 E*8 V
spare7 Spare calibration
spare_7_2 2BC 0.00 "" 0000 E*8 V
spare7 Spare calibration
spare_8_1 2BE 0.00 "" 0000 E*8 V
spare8 Spare calibration
spare_8_2 2C0 0.00 "" 0000 E*8 V
spare8 Spare calibration
air_comp_max_set_points_rat0 2C2 931.09 KPA 0870 E*2.31985 D
pgsmxs Rating 0 max allowable air comp pressure set point
air_comp_max_set_points_rat1 2C4 1034.98 KPA 0961 E*2.31985 D
pgsmxs Rating 1 max allowable air comp pressure set point
air_comp_max_set_points_rat2 2C6 413.82 KPA 03c0 E*2.31985 D
pgsmxs Rating 2 max allowable air comp pressure set point
air_comp_min_set_points_rat0 2C8 413.82 KPA 03c0 E*2.31985 D
pgsmns Rating 0 min allowable air comp pressure set point
air_comp_min_set_points_rat1 2CA 413.82 KPA 03c0 E*2.31985 D
pgsmns Rating 1 min allowable air comp pressure set point
air_comp_min_set_points_rat2 2CC 206.91 KPA 01e0 E*2.31985 D
pgsmns Rating 2 min allowable air comp pressure set point

NAME: ambient_air_temperature ADDR: 2CE UNT: "" OWN: V CODE: amairt


EQN: (E+40)*14.4
ambient air temp as a function of a raw sensor val
Sensor_val| HEX| ""
--------------------------------
0.0| 0d80| 200.00
32.0| 0aa0| 148.89
64.0| 08fe| 119.86
96.0| 081e| 104.31
128.0| 0784| 93.61
160.0| 070c| 85.28
192.0| 06ac| 78.61
224.0| 0659| 72.85
256.0| 0610| 67.78
288.0| 05ce| 63.19
320.0| 0592| 59.03
352.0| 055a| 55.14
384.0| 0526| 51.53
416.0| 04f5| 48.13
448.0| 04c6| 44.86
480.0| 0498| 41.67
512.0| 046c| 38.61
544.0| 043f| 35.49
576.0| 0414| 32.50
608.0| 03e7| 29.38
640.0| 03bb| 26.32
672.0| 038d| 23.13
704.0| 035e| 19.86
736.0| 032c| 16.39
768.0| 02f7| 12.71
800.0| 02be| 8.75
832.0| 027f| 4.38
864.0| 0237| -0.63
896.0| 01e1| -6.60
928.0| 0172| -14.31
960.0| 00c6| -26.25
992.0| 0000| -40.00
1024.0| 0000| -40.00

NAME: analog_config_id ADDR: 310 UNT: "" OWN: E CODE: ancfg


EQN: E
Indx of Cal Blks usd by VEPS to conf. anlg chnls
pid_pin| HEX| ""
--------------------------------
0.0| 0001| 1.0
1.0| 0001| 1.0
2.0| 0001| 1.0
3.0| 0001| 1.0
4.0| 0001| 1.0
5.0| 0001| 1.0
6.0| 0000| 0.0
7.0| 0000| 0.0
8.0| 0000| 0.0
9.0| 0000| 0.0
10.0| 0001| 1.0
11.0| 0001| 1.0
12.0| 0000| 0.0
13.0| 0001| 1.0
14.0| 0001| 1.0
15.0| 0001| 1.0

NAME: certification_number ADDR: 330 UNT: DEC OWN: B CODE: zcertn


EQN: E
Certification Number for each 6N4M rating group
Elements| HEX| DEC
--------------------------------
1| 0497| 1175.0
2| 0498| 1176.0
3| 0499| 1177.0
4| 04a3| 1187.0

NAME: dp_offset_default ADDR: 338 UNT: "" OWN: B CODE: dpofdf


EQN: E
avg press sensor, f(engine coolant temp)
dgC| HEX| ""
--------------------------------
15.0| 0000| 0.0
20.0| 0000| 0.0
25.0| 0000| 0.0
30.0| 0000| 0.0
35.0| 0000| 0.0
40.0| 0000| 0.0
45.0| 0000| 0.0
50.0| 0000| 0.0
55.0| 0000| 0.0
60.0| 0000| 0.0
65.0| 0000| 0.0
70.0| 0000| 0.0
75.0| 0000| 0.0
80.0| 0000| 0.0
85.0| 0000| 0.0
90.0| 0000| 0.0
95.0| 0000| 0.0

NAME: egr_flow_rate ADDR: 35A UNT: "" OWN: B CODE: egrate


EQN: E*256
EGR flow rate in (kg^.5)*(m^1.5)/min, f(differ P)
Boost-kPa| HEX| ""
--------------------------------
0.0| 0000| 0.0000
1.0| 0000| 0.0000
2.0| 0000| 0.0000
3.0| 0000| 0.0000
4.0| 0000| 0.0000
5.0| 0000| 0.0000
6.0| 0000| 0.0000
7.0| 0000| 0.0000
8.0| 0000| 0.0000
9.0| 0000| 0.0000
10.0| 0000| 0.0000
11.0| 0000| 0.0000
12.0| 0000| 0.0000
13.0| 0000| 0.0000
14.0| 0000| 0.0000
15.0| 0000| 0.0000
16.0| 0000| 0.0000

NAME: egr_rate_deriv_gain ADDR: 37C UNT: "" OWN: B CODE: egrder


EQN: E*10000
derivative gain for EGR rate control
unitless| HEX| ""
--------------------------------
-2.0| 0000| 0.00000
-1.5| 0000| 0.00000
-1.0| 0000| 0.00000
-0.5| 0000| 0.00000
0.0| 0000| 0.00000
0.5| 0000| 0.00000
1.0| 0000| 0.00000
1.5| 0000| 0.00000
2.0| 0000| 0.00000

NAME: egr_rate_integ_gain ADDR: 38E UNT: "" OWN: B CODE: egrint


EQN: E*40000
integral gain for EGR rate control
unitless| HEX| ""
--------------------------------
-2.0| 0000| 0.000000
-1.5| 0000| 0.000000
-1.0| 0000| 0.000000
-0.5| 0000| 0.000000
0.0| 0000| 0.000000
0.5| 0000| 0.000000
1.0| 0000| 0.000000
1.5| 0000| 0.000000
2.0| 0000| 0.000000

NAME: egr_rate_prop_gain ADDR: 3A0 UNT: "" OWN: B CODE: egrprp


EQN: E*10000
proportional gain for EGR rate control
unitless| HEX| ""
--------------------------------
-2.0| 0000| 0.00000
-1.5| 0000| 0.00000
-1.0| 0000| 0.00000
-0.5| 0000| 0.00000
0.0| 0000| 0.00000
0.5| 0000| 0.00000
1.0| 0000| 0.00000
1.5| 0000| 0.00000
2.0| 0000| 0.00000

NAME: egr_temperature ADDR: 3B2 UNT: "" OWN: B CODE: egrtmp


EQN: (E+40)*14.4
EGR temp as a function of raw sensor values
Sensor_val| HEX| ""
--------------------------------
0.0| 0000| -40.00
64.0| 0000| -40.00
128.0| 0000| -40.00
192.0| 0000| -40.00
256.0| 0000| -40.00
320.0| 0000| -40.00
384.0| 0000| -40.00
448.0| 0000| -40.00
512.0| 0000| -40.00
576.0| 0000| -40.00
640.0| 0000| -40.00
704.0| 0000| -40.00
768.0| 0000| -40.00
832.0| 0000| -40.00
896.0| 0000| -40.00
960.0| 0000| -40.00
1024.0| 0000| -40.00

NAME: ess_analog_switch_high_ends ADDR: 3D4 UNT: "" OWN: V CODE:


essshe EQN: E
if cnts>ESSSHE then decoded as ESS high digital in
Sensor_val| HEX| ""
--------------------------------
0.0| 0133| 307.0
1.0| 0000| 0.0
2.0| 0176| 374.0
3.0| 0000| 0.0
4.0| 01eb| 491.0
5.0| 023d| 573.0
6.0| 02c2| 706.0
7.0| 0366| 870.0

NAME: ess_analog_switch_low_ends ADDR: 3E4 UNT: "" OWN: V CODE: esssle


EQN: E
ess_analog_switch_low_ends
Sensor_val| HEX| ""
--------------------------------
0.0| 0110| 272.0
1.0| 0000| 0.0
2.0| 0153| 339.0
3.0| 0000| 0.0
4.0| 01c6| 454.0
5.0| 0212| 530.0
6.0| 0299| 665.0
7.0| 0347| 839.0

NAME: ether_block_injection ADDR: 3F4 UNT: "" OWN: V CODE: eiblt


EQN: E*10
ether injection block time in secs after crank
dgC| HEX| ""
--------------------------------
-40.0| 012c| 30.0
-37.2| 012c| 30.0
-34.4| 012c| 30.0
-31.7| 012c| 30.0
-28.9| 012c| 30.0
-26.1| 012c| 30.0
-23.3| 0110| 27.2
-20.6| 00f4| 24.4
-17.8| 00d8| 21.6
-15.0| 00bc| 18.8
-12.2| 00a1| 16.1
-9.4| 0085| 13.3
-6.7| 0069| 10.5
-3.9| 004d| 7.7
-1.1| 0032| 5.0
1.7| 0000| 0.0
4.4| 0000| 0.0
7.2| 0000| 0.0
10.0| 0000| 0.0

NAME: ether_pre_load ADDR: 41A UNT: "" OWN: V CODE: eiplt


EQN: E*10
ether injection pre-load time in secs before crank
dgC| HEX| ""
--------------------------------
-40.0| 001e| 3.0
-37.2| 001b| 2.7
-34.4| 0019| 2.5
-31.7| 0017| 2.3
-28.9| 0015| 2.1
-26.1| 0012| 1.8
-23.3| 0010| 1.6
-20.6| 000e| 1.4
-17.8| 000c| 1.2
-15.0| 000a| 1.0
-12.2| 0009| 0.9
-9.4| 0008| 0.8
-6.7| 0007| 0.7
-3.9| 0006| 0.6
-1.1| 0005| 0.5
1.7| 0000| 0.0
4.4| 0000| 0.0
7.2| 0000| 0.0
10.0| 0000| 0.0

NAME: exhaust_temperature ADDR: 440 UNT: "" OWN: V CODE: exconv


EQN: (E+40)*14.4
ExhaustTemp LookUp Tbl to convert A/D cnts to degC
Sensor_val| HEX| ""
--------------------------------
0.0| 0000| -40.00
64.0| 0000| -40.00
128.0| 0000| -40.00
192.0| 0000| -40.00
256.0| 0000| -40.00
320.0| 0000| -40.00
384.0| 0220| -2.22
448.0| 0689| 76.18
512.0| 0c38| 177.22
576.0| 13d8| 312.78
640.0| 1ea5| 504.79
704.0| 2f49| 800.63
768.0| 3fff| 1097.71
832.0| 3fff| 1097.71
896.0| 3fff| 1097.71
960.0| 3fff| 1097.71
1024.0| 3fff| 1097.71

NAME: gear_ratio_lookup_table ADDR: 462 UNT: "" OWN: O CODE: essrlt


EQN: E*2048
ESS transmission gear ratios from low to high gear
Sensor_val| HEX| ""
--------------------------------
0.0| 66a4| 12.83008
1.0| 3d85| 7.68994
2.0| 2bd7| 5.47998
3.0| 1f1f| 3.89014
4.0| 167b| 2.81006
5.0| 0fd7| 1.97998
6.0| 0b48| 1.41016
7.0| 0800| 1.00000
8.0| 05c3| 0.72021
9.0| 0000| 0.00000
10.0| 0000| 0.00000
11.0| 0000| 0.00000
12.0| 0000| 0.00000
13.0| 0000| 0.00000
14.0| 0000| 0.00000
15.0| 0000| 0.00000

NAME: idle_rpm ADDR: 482 UNT: "" OWN: B CODE: idlrpm


EQN: E*4
idle RPM look-up: idle RPM based on oil temp
dgC| HEX| ""
--------------------------------
-40.0| 0e10| 900.00
-27.8| 0e10| 900.00
-15.6| 0e10| 900.00
-3.3| 0e10| 900.00
8.9| 0de8| 890.00
21.1| 0dc0| 880.00
33.3| 0be0| 760.00
45.6| 0960| 600.00
57.8| 0960| 600.00
70.0| 0960| 600.00
82.2| 0960| 600.00
94.4| 0960| 600.00
106.7| 0960| 600.00
118.9| 0960| 600.00
131.1| 0960| 600.00
143.3| 0960| 600.00
155.6| 0960| 600.00

NAME: shutdn_max_crankcase_pressure ADDR: 4A4 UNT: "" OWN: V CODE:


smxccp EQN: E*74.2352
if CCP > SMXCCP log a scaledhilimit fault
Tq*RPM| HEX| ""
--------------------------------
0.0| 02e6| 9.995
150.0| 02e6| 9.995
300.0| 02e6| 9.995
450.0| 02e6| 9.995
600.0| 02e6| 9.995
750.0| 02e6| 9.995
900.0| 02e6| 9.995
1050.0| 02e6| 9.995
1200.0| 02e6| 9.995
1350.0| 02e6| 9.995
1500.0| 02e6| 9.995
1650.0| 02e6| 9.995
1800.0| 02e6| 9.995
1950.0| 02e6| 9.995
2100.0| 02e6| 9.995
2250.0| 02e6| 9.995
2400.0| 02e6| 9.995

NAME: smoke_control_axis ADDR: 4C6 UNT: "" OWN: V CODE: scbst


EQN: E*256
assigns boost KPAA vals to press axis of ATQ Tbls
Boost-kPa| HEX| ""
--------------------------------
0.0| 0000| 0.0000
14.0| 0000| 0.0000
28.0| 0000| 0.0000
41.0| 0000| 0.0000
55.0| 0000| 0.0000
69.0| 0026| 0.1484
83.0| 00e1| 0.8789
97.0| 023a| 2.2266
110.0| 0349| 3.2852
124.0| 042d| 4.1758
138.0| 04ed| 4.9258
152.0| 05a4| 5.6406
166.0| 0656| 6.3359
179.0| 06f4| 6.9531
193.0| 07ab| 7.6680
207.0| 07ff| 7.9961
221.0| 0800| 8.0000
234.0| 0800| 8.0000
248.0| 0800| 8.0000
262.0| 0800| 8.0000
276.0| 0800| 8.0000
290.0| 0800| 8.0000
303.0| 0800| 8.0000
317.0| 0800| 8.0000
331.0| 0800| 8.0000
345.0| 0800| 8.0000
359.0| 0800| 8.0000
372.0| 0800| 8.0000
386.0| 0800| 8.0000
400.0| 0800| 8.0000
414.0| 0800| 8.0000
428.0| 0800| 8.0000
441.0| 0800| 8.0000

NAME: t2_auto_dn_lo_base ADDR: 508 UNT: RPM OWN: V CODE: astdlb


EQN: E*4
Mininimum downshift point at 0% throttle
Elements| HEX| RPM
--------------------------------
1| 11f8| 1150.00
2| 11f8| 1150.00
3| 11f8| 1150.00
4| 11f8| 1150.00

NAME: t2_auto_dwn_rpm ADDR: 510 UNT: RPM OWN: V CODE: astadr


EQN: E*4
100% Throttle downshift point
Elements| HEX| RPM
--------------------------------
1| 1388| 1250.00
2| 1388| 1250.00
3| 1450| 1300.00
4| 1450| 1300.00

NAME: t2_auto_up_lo_base ADDR: 518 UNT: RPM OWN: V CODE: astulb


EQN: E*4
Minimum upshift point at 20% throttle
Elements| HEX| RPM
--------------------------------
1| 19c8| 1650.00
2| 19c8| 1650.00
3| 1770| 1500.00
4| 1770| 1500.00

NAME: t2_auto_up_rpm ADDR: 520 UNT: RPM OWN: V CODE: astaur


EQN: E*4
100% throttle upshift point
Elements| HEX| RPM
--------------------------------
1| 1c20| 1800.00
2| 1c20| 1800.00
3| 1b58| 1750.00
4| 1b58| 1750.00

NAME: t2_cc_up_rpm ADDR: 528 UNT: RPM OWN: V CODE: astcur


EQN: E*4
lower upshift RPM if CC+9th+%RTQ<ASTCDM for ASTCRT
Elements| HEX| RPM
--------------------------------
1| 1a64| 1689.00
2| 1a64| 1689.00
3| 1838| 1550.00
4| 1838| 1550.00

NAME: t2_delta_rpm ADDR: 530 UNT: RPM OWN: V CODE: astder


EQN: E*4
Dither RPM from sync used for splitter engagements
Elements| HEX| RPM
--------------------------------
1| 00a0| 40.00
2| 00a0| 40.00
3| 00a0| 40.00
4| 00a0| 40.00

NAME: t2_failed_engage_rpm ADDR: 538 UNT: rpm OWN: V CODE: astfer


EQN: E*4
Max expctd dwnsft pt frm drct gr (10 spds on 13/18
Elements| HEX| rpm
--------------------------------
1| 15e0| 1400.00
2| 15e0| 1400.00
3| 15e0| 1400.00
4| 15e0| 1400.00

NAME: t2_jake_downshift_offset ADDR: 540 UNT: RPM OWN: V CODE: astjdo


EQN: E*4
downshift point raised ASTJDO RPM if jakes ON
Elements| HEX| RPM
--------------------------------
1| 0258| 150.00
2| 0258| 150.00
3| 0320| 200.00
4| 0320| 200.00

NAME: t2_jake_upshift_offset ADDR: 548 UNT: RPM OWN: V CODE: astjuo


EQN: E*4
upshift point raised ASTJUO RPM if jakes ON
Elements| HEX| RPM
--------------------------------
1| 0320| 200.00
2| 0320| 200.00
3| 0320| 200.00
4| 0320| 200.00

NAME: t2_man_dwnshift_rpm ADDR: 550 UNT: rpm OWN: V CODE: astmdr


EQN: E*4
Max expected manual level dwnsft pt frm drct gr.
Elements| HEX| rpm
--------------------------------
1| 15e0| 1400.00
2| 15e0| 1400.00
3| 1900| 1600.00
4| 1900| 1600.00

NAME: t2_man_upshift_rpm ADDR: 558 UNT: RPM OWN: V CODE: astmur


EQN: E*4
Min expected manual lever dwnshft into top gear
Elements| HEX| RPM
--------------------------------
1| 15e0| 1400.00
2| 15e0| 1400.00
3| 12c0| 1200.00
4| 12c0| 1200.00

NAME: t2_ratio_lookup_table ADDR: 560 UNT: RTO OWN: V CODE: astrlt


EQN: E*1024
Eaton Top2 8th,9th,10th transmission gear ratios
Elements| HEX| RTO
--------------------------------
1| 0569| 1.3525
2| 0400| 1.0000
3| 02f7| 0.7412

NAME: t2_rtd_down_offset ADDR: 566 UNT: rpm OWN: V CODE: astrdo


EQN: E*4
RPM offset used to inc dwnsft pnt at high throttle
Elements| HEX| rpm
--------------------------------
1| 0000| 0.00
2| 0000| 0.00
3| 00c8| 50.00
4| 00c8| 50.00

NAME: t2_split_diseng_time ADDR: 56E UNT: SEC OWN: V CODE: astspt


EQN: E*40
Maximum time allowed to disengage the splitter
Elements| HEX| SEC
--------------------------------
1| 0078| 3.000
2| 0078| 3.000
3| 0078| 3.000
4| 0078| 3.000

NAME: tco_temperature ADDR: 576 UNT: "" OWN: B CODE: tcotmp


EQN: (E+40)*14.4
tco temp as a function of a raw sensor value(cnts)
Sensor_val| HEX| ""
--------------------------------
0.0| 0000| -40.00
64.0| 0000| -40.00
128.0| 0000| -40.00
192.0| 0000| -40.00
256.0| 0000| -40.00
320.0| 0000| -40.00
384.0| 0000| -40.00
448.0| 0000| -40.00
512.0| 0000| -40.00
576.0| 0000| -40.00
640.0| 0000| -40.00
704.0| 0000| -40.00
768.0| 0000| -40.00
832.0| 0000| -40.00
896.0| 0000| -40.00
960.0| 0000| -40.00
1024.0| 0000| -40.00
NAME: temperature_conv ADDR: 598 UNT: "" OWN: B CODE: tconv
EQN: (E+40)*14.4
Temperature look-up table to conv counts to degC
Sensor_val| HEX| ""
--------------------------------
0.0| 0d80| 200.00
32.0| 0a68| 145.00
64.0| 08f4| 119.17
96.0| 0818| 103.89
128.0| 0780| 93.33
160.0| 070c| 85.28
192.0| 06ab| 78.54
224.0| 0658| 72.78
256.0| 0612| 67.92
288.0| 05d0| 63.33
320.0| 0596| 59.31
352.0| 055f| 55.49
384.0| 052b| 51.88
416.0| 04fa| 48.47
448.0| 04cd| 45.35
480.0| 04a1| 42.29
512.0| 0475| 39.24
544.0| 044a| 36.25
576.0| 041f| 33.26
608.0| 03f5| 30.35
640.0| 03ca| 27.36
672.0| 039e| 24.31
704.0| 0373| 21.32
736.0| 0343| 17.99
768.0| 0312| 14.58
800.0| 02df| 11.04
832.0| 02a6| 7.08
864.0| 0269| 2.85
896.0| 0221| -2.15
928.0| 01cb| -8.13
960.0| 015e| -15.69
992.0| 00a8| -28.33
1024.0| 0000| -40.00

NAME: turbo_overboost_fault_press ADDR: 5DA UNT: "" OWN: B CODE:


tbobfp EQN: E*2.31985
Max boost prs before ovrbst fault becomes present
RPM| HEX| ""
--------------------------------
150.0| 03a1| 400.46
300.0| 03a1| 400.46
450.0| 03a1| 400.46
600.0| 03a1| 400.46
750.0| 03a1| 400.46
900.0| 03a1| 400.46
1050.0| 03a1| 400.46
1200.0| 03a1| 400.46
1350.0| 03a1| 400.46
1500.0| 03a1| 400.46
1650.0| 03a1| 400.46
1800.0| 03a1| 400.46
1950.0| 03a1| 400.46
2100.0| 03a1| 400.46
2250.0| 03a1| 400.46
2400.0| 03a1| 400.46
2550.0| 03a1| 400.46

NAME: turbo_overspeed_fault_tcrpm ADDR: 5FC UNT: "" OWN: B CODE:


tbosfs EQN: E/128
max turbo speed RPM before overspd fault present
RPM| HEX| ""
--------------------------------
150.0| 03e4| 127488.0
300.0| 03e4| 127488.0
450.0| 03e4| 127488.0
600.0| 03e4| 127488.0
750.0| 03e4| 127488.0
900.0| 03e4| 127488.0
1050.0| 03e4| 127488.0
1200.0| 03e4| 127488.0
1350.0| 03e4| 127488.0
1500.0| 03e4| 127488.0
1650.0| 03e4| 127488.0
1800.0| 03e4| 127488.0
1950.0| 03e4| 127488.0
2100.0| 03e4| 127488.0
2250.0| 03e4| 127488.0
2400.0| 03e4| 127488.0
2550.0| 03e4| 127488.0

NAME: upc_6n4m ADDR: 61E UNT: DEC OWN: B CODE: pc6n4m


EQN: E
6N4M UPC codes for 4 Horsepower Ratings
Elements| HEX| DEC
--------------------------------
1| 1c3e| 7230.0
2| 1c3f| 7231.0
3| 1c40| 7232.0
4| 1c41| 7233.0

NAME: vnt_deriv_gain ADDR: 626 UNT: "" OWN: B CODE: vntdgn


EQN: E*10000
derivative gain for intake boost pressure ctrl
unitless| HEX| ""
--------------------------------
-160.0| 0000| 0.00000
-120.0| 0000| 0.00000
-80.0| 0000| 0.00000
-40.0| 0000| 0.00000
0.0| 0000| 0.00000
40.0| 0000| 0.00000
80.0| 0000| 0.00000
120.0| 0000| 0.00000
160.0| 0000| 0.00000

NAME: vnt_integ_gain ADDR: 638 UNT: "" OWN: B CODE: vntign


EQN: E*40000
integral gain for intake boost pressure ctrl
unitless| HEX| ""
--------------------------------
-160.0| 0000| 0.000000
-120.0| 0000| 0.000000
-80.0| 0000| 0.000000
-40.0| 0000| 0.000000
0.0| 0000| 0.000000
40.0| 0000| 0.000000
80.0| 0000| 0.000000
120.0| 0000| 0.000000
160.0| 0000| 0.000000

NAME: vnt_prop_gain ADDR: 64A UNT: "" OWN: B CODE: vntpgn


EQN: E*10000
proportional gain for intake boost pressure ctrl
unitless| HEX| ""
--------------------------------
-160.0| 0000| 0.00000
-120.0| 0000| 0.00000
-80.0| 0000| 0.00000
-40.0| 0000| 0.00000
0.0| 0000| 0.00000
40.0| 0000| 0.00000
80.0| 0000| 0.00000
120.0| 0000| 0.00000
160.0| 0000| 0.00000

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
acs_torque_limit_rpm 65C 2500.0 RPM 09c4 E E
actlrp ratedRPM=MIN(dtlrpm,actlrp) if DinX=14 & Gnd
actual_torque_scaling 65E 2436.4 N*m 0705 E/1.3558 B
ztqscl max TRQ of engine family-ref for all internal TRQs
air_boi_adv_max 660 39.03 dgC 0472 (E+40)*14.4 B
airmax max AIRBOI temp w/ 16 steps from AIRMIN to AIRMAX
air_boi_adv_min 662 -9.03 dgC 01be (E+40)*14.4 B
airmin min AIRBOI temp w/ 16 steps from AIRMIN to AIRMAX
air_comp_int_gain 664 1.56 RPM 0005 E*3.2 O
pgsig Air Comp press gov integral gain in RPM/(PSI*SEC)
air_comp_prop_gain 666 32.000 RPM 1000 E*128 O
pgspg Air Comp pressure gov proportional gain in RPM/PSI
air_high_temp_ss 668 244.38 dgC 0fff (E+40)*14.4 B
arhtss air temp > arhtss + boisst : use BOISSR
air_low_temp_ss 66A -40.00 dgC 0000 (E+40)*14.4 B
arltss air temp < arltss - boisst : use BOISSR
air_temp_fan_off 66C 55.00 dgC 0558 (E+40)*14.4 E
atoff air temp < atoff to turn FanCntrl#1 off
air_temp_fan1_on 66E 65.97 dgC 05f6 (E+40)*14.4 E
atf1on AirTmp>ATF1ON for single/.5 dual/high speed FANs
air_temp_fan2_on 670 62.99 dgC 05cb (E+40)*14.4 E
atf2on AirTmp>ATF2ON to enable low speed of dual spd FAN
air_temp_high_to_low 672 52.01 dgC 052d (E+40)*14.4 V
athilo Air Temp for switch from hi to lo fan speed
air_to_charge_delta 674 30.00 dgC 01b0 E*14.4 V
atsdel AmbTemp=Inlet-(Oil-Inlet)*ATSDEL/100dgF w/o sensor
air_tq_reduction_max_airt 676 250.00 dgC 1050 (E+40)*14.4 E
atxtmp Air Temp > ATXTMP for max AIR TEMP TQ LIMITING
air_tq_reduction_max_rpm 678 2250.00 RPM 2328 E*4 B
atxrpm RPM > ATXRPM for max AIR TEMP TQ LIMITING
air_tq_reduction_min_airt 67A 250.00 dgC 1050 (E+40)*14.4 E
atntmp Air Temp > ATNTMP for min AIR TEMP TQ LIMITING
air_tq_reduction_min_rpm 67C 300.00 RPM 04b0 E*4 B
atnrpm RPM > ATNRPM for min AIR TEMP TQ LIMITING
avtq_filterconst 67E 0.1992 % @ 0033 E*256 V
avtqfc newAVTQ=oldAVTQ+avtqfc*(LstCylFrFTQ/MAXTQ-oldAVTQ)
air_temp_leadlag_k1 680 0.819000 %@1S d1aa E*65536 V
atllk1 lead/lag filter constants @1sec to compnsate for..
air_temp_leadlag_k2 682 6.00000 %@1S 6000 E*4096 V
atllk2 ..plastic AirTemp Sensor slow response time...
air_temp_leadlag_k3 684 5.81909 %@1S 5d1b E*4096 V
atllk3 ..AirTmp=K1*LastAirTmp+K2*A/DAirTmp-K3*LastA/DAirT
atp_rpm_factor 686 1960.00 "" 1ea0 E*4 B
atpdiv Scaling factor used in rescaling ATP
aux_temp_tq_correction_pid 688 0.0 PID 0000 E B
axttcp Temp. used for AXTTQC lookup axis
axle_ratio 68A 2.790 RTO 0117 E*100 D
axlrat VSS: Axle ratio
bar_boi_adv_max 68C 94.40 KPA 00db E*2.31985 V
barmax max BARBOI kpa w/ 16 steps from BARMIN to BARMAX
bar_boi_adv_min 68E 62.50 KPA 0091 E*2.31985 V
barmin min BARBOI kpa w/ 16 steps from BARMIN to BARMAX
baro_low_press_ss 690 0.00 KPa 0000 E*2.31985 B
brlpss baro < brlpss : use BOISSR
baro_max_rpm 692 750.00 RPM 0bb8 E*4 E
bpmxrp RPM<bpmxrp update calcd baro/AmbTmp if no sensors
baro_nox_1min_adv_max 694 80.00 dgC 06c0 (E+40)*14.4 V
bx1amx max value of BX1MLC temperature axis
baro_nox_1min_adv_min 696 0.00 dgC 0240 (E+40)*14.4 V
bx1amn min value of BX1MLC temperature axis
baro_nox_adj_high_thresh 698 220.70 kPa 0200 E*2.31985 V
bnshtr value < which BARBOI may be adjusted by bnaadj
baro_nox_adj_low_thresh 69A 79.75 kPa 00b9 E*2.31985 V
bnsltr value > which BARBOI may be adjusted by bnaadj
baro_nox_temp_weighting_pid0 69C 110.0 "" 006e E V
bxtwp0 eng temp PID used for baro advanced strategy
baro_nox_temp_weighting_pid1 69E 172.0 "" 00ac E V
bxtwp1 eng temp PID used for baro advanced strategy
boi_cold_adv_min 6A0 -9.03 dgC 01be (E+40)*14.4 V
boimin min CBOIAD temp w/ 16 steps from boimin to boimax
boi_cold_adv_max 6A2 39.03 dgC 0472 (E+40)*14.4 V
boimax max CBOIAD temp w/ 16 steps from boimin to boimax
boi_fudge_factor 6A4 1.0000 Mlt 0100 E*256 V
bimult Final BOI = bimult * Provisional BOI
boi_temp_weighting_pid0 6A6 175.0 PID 00af E V
boipd0 1st temperature PID used for CBOIAD temp weighting
boi_temp_weighting_pid1 6A8 172.0 PID 00ac E V
boipd1 2nd temperature PID used for CBOIAD temp weighting
boic_high_temp_ss 6AA 244.38 dgC 0fff (E+40)*14.4 B
boicht cold temp > boicht + boisst : use BOISSR
boic_low_temp_ss 6AC -40.00 dgC 0000 (E+40)*14.4 B
boiclt cold temp < boiclt - boisst : use BOISSR
boost_max_rpm 6AE 800.00 RPM 0c80 E*4 V
tbwrpm RPM < tbwrpm to log turbo boost sensor failed high
cc_ftmode_prop_gain 6B0 0.750 R/P 0060 E*128 O
ftppg fire truck pressure governor proportional gain
cc_mph_ramprate 6B2 2.0000 M/S 0200 E*256 V
ccrmph cruise control resum/accel ramp rate in MPH / sec
cc_pto_init_rpm 6B4 1000.00 RPM 0fa0 E*4 D
ccptrp PTO: Initial Cruise Switch PTO RPM set point
cc_rpm_minimum 6B6 1000.00 RPM 0fa0 E*4 E
ccminr RPM > ccminr to enable cruise control
clock_max_jump 6B8 31.0 Day 001f E V
clktoo min clock forward jump in days to log error
comp_bleed_max_cbv_dp 6BA -1.7 kPa ffffffff E/1.72425 B
cbvmdp max diff press across Turbo cbv to let valve open
comp_bleed_max_rpm 6BC 4095.75 RPM 3fff E*4 B
cbvrpm RPM above which CBV will be forced off
comp_bleed_rpm_hyst 6BE 0.00 RPM 0000 E*4 B
cbvhst RPM < cbvrpm=cbvhys to allow CBV logic to operate
cool_boi_adv_max 6C0 60.00 dgC 05a0 (E+40)*14.4 B
colmax max COLBOI temp w/ 16 steps from COLMIN to COLMAX
cool_boi_adv_min 6C2 -9.03 dgC 01be (E+40)*14.4 B
colmin min COLBOI temp w/ 16 steps from COLMIN to COLMAX
cool_high_temp_ss 6C4 244.38 dgC 0fff (E+40)*14.4 B
clhtss cool temp > clhtss + boisst : use BOISSR
cool_low_temp_ss 6C6 -40.00 dgC 0000 (E+40)*14.4 B
clltss cool temp < clltss - boisst : use BOISSR
cool_temp_fan1_on 6C8 97.99 dgC 07c3 (E+40)*14.4 E
ctf1on CoolTmp>CTF1ON for single/.5 dual/hi speed FANs
cool_temp_fan2_on 6CA 95.97 dgC 07a6 (E+40)*14.4 E
ctf2on CoolTmp>CTF2ON to enable low speed of 2 speed FAN
cool_temp_fan_off 6CC 92.01 dgC 076d (E+40)*14.4 E
ctoff coolant temp < ctoff to turn FanOut#1 and #2 off
cool_temp_high_to_low 6CE 87.99 dgC 0733 (E+40)*14.4 V
cthilo Cool Temp for switch from hi to lo fan speed
cool_temp_leadlag_k1 6D0 0.779007 %@1 c76d E*65536 V
ctllk1 lead/lag filter constants @1sec to compnsate for..
cool_temp_leadlag_k2 6D2 2.50000 %@1 2800 E*4096 V
ctllk2 ...Coolant Temp sensor slow response time ...
cool_temp_leadlag_k3 6D4 2.27905 %@1 2477 E*4096 V
ctllk3 ..CltTmp=K1*LastCltTmp+K2*A/DCltTmp-K3*LastA/DCltT
db_temp_disable 6D6 -12.01 dgC 0193 (E+40)*14.4 E
dbtdis DYNAMIC BRAKING not allowed until AirTmp>DBTEN, ..
db_temp_enable 6D8 -9.03 dgC 01be (E+40)*14.4 E
dbten ..then allowed until AirTemp<DBTDIS
default_fuel_temp 6DA 30.00 dgC 03f0 (E+40)*14.4 V
dffute default fuel temp if no sensor
default_oil_temp 6DC 80.00 dgC 06c0 (E+40)*14.4 V
dfolte default oil temp if no sensor
digital_torque_limit_rpm 6DE 2500.0 RPM 09c4 E B
dtlrpm ratedRPM=MIN(dtlrpm,actlrp) if DinX=14 & Gndd
active_diagnostic_enable_F3 6E0 1.0 Flg 1 E V
# OUT F3: set for stuck high diagnostics
active_diagnostic_enable_A2 6E0.1 1.0 Flg 1 E V
# OUT A2: set for stuck high diagnostics
active_diagnostic_enable_W3 6E0.2 1.0 Flg 1 E V
# OUT W3: set for stuck high diagnostics
active_diagnostic_enable_X3 6E0.3 1.0 Flg 1 E V
# OUT X3: set for stuck high diagnostics
active_diagnostic_enable_Y3 6E0.4 1.0 Flg 1 E V
# OUT Y3: set for stuck high diagnostics
active_diagnostic_enable_A1 6E0.5 1.0 Flg 1 E V
# OUT A1: set for stuck high diagnostics
active_diagnostic_enable_S3 6E1.2 1.0 Flg 1 E V
# OUT S3: set for stuck LOW diagnostics
active_diagnostic_enable_T3 6E1.3 1.0 Flg 1 E V
# OUT T3: set for stuck LOW diagnostics
active_diagnostic_enable_B2 6E1.4 1.0 Flg 1 E V
# OUT B2: set for stuck high diagnostics
active_diagnostic_enable_B1 6E1.5 1.0 Flg 1 E V
# OUT B1: set for stuck high diagnostics
driver_diagnostic_disable_F3 6E2 0.0 Flg 0 E V
# Disables internal driver diagnostics - High Side
driver_diagnostic_disable_A2 6E2.1 0.0 Flg 0 E V
# Disables internal driver diagnostics - High Side
driver_diagnostic_disable_W3 6E2.2 0.0 Flg 0 E V
# Disables internal driver diagnostics - High Side
driver_diagnostic_disable_X3 6E2.3 0.0 Flg 0 E V
# Disables internal driver diagnostics - High Side
driver_diagnostic_disable_Y3 6E2.4 0.0 Flg 0 E V
# Disables internal driver diagnostics - High Side
driver_diagnostic_disable_A1 6E2.5 0.0 Flg 0 E V
# Disables internal driver diagnostics - High Side
driver_diagnostic_disable_S3 6E3.2 0.0 Flg 0 E V
# Disables internal driver diagnostics - High Side
driver_diagnostic_disable_T3 6E3.3 0.0 Flg 0 E V
# Disables internal driver diagnostics - High Side
driver_diagnostic_disable_B2 6E3.4 0.0 Flg 0 E V
# Disables internal driver diagnostics - High Side
driver_diagnostic_disable_B1 6E3.5 0.0 Flg 0 E V
# Disables internal driver diagnostics - High Side
passive_diagnostic_enable_F3 6E4 0.0 Flg 0 E E
# OUT F3: set for stuck low diagnostics-load req'd
passive_diagnostic_enable_A2 6E4.1 0.0 Flg 0 E E
# OUT A2: set for stuck low diagnostics-load req'd
passive_diagnostic_enable_W3 6E4.2 0.0 Flg 0 E E
# OUT W3: set for stuck low diagnostics-load req'd
passive_diagnostic_enable_X3 6E4.3 0.0 Flg 0 E E
# OUT X3: set for stuck low diagnostics-load req'd
passive_diagnostic_enable_Y3 6E4.4 0.0 Flg 0 E E
# OUT Y3: set for stuck low diagnostics-load req'd
passive_diagnostic_enable_A1 6E4.5 0.0 Flg 0 E E
# OUT A1: set for stuck low diagnostics-load req'd
passive_diagnostic_enable_S3 6E5.2 1.0 Flg 1 E E
# OUT S3: set for stuck HIGH diagnostics-load req'd
passive_diagnostic_enable_T3 6E5.3 1.0 Flg 1 E E
# OUT T3: set for stuck HIGH diagnostics-load req'd
passive_diagnostic_enable_B2 6E5.4 0.0 Flg 0 E V
# OUT B2: set for stuck low diagnostics-load req'd
passive_diagnostic_enable_B1 6E5.5 0.0 Flg 0 E V
# OUT B1: set for stuck low diagnostics-load req'd
polarity_invert_F3 6E6 0.0 Flg 0 E O
# OUT F3: set to sink current when OFF else when ON
polarity_invert_A2 6E6.1 1.0 Flg 1 E O
# OUT A2: set to sink current when OFF else when ON
polarity_invert_W3 6E6.2 0.0 Flg 0 E O
# OUT W3: set to sink current when OFF else when ON
polarity_invert_X3 6E6.3 0.0 Flg 0 E O
# OUT X3: set to sink current when OFF else when ON
polarity_invert_Y3 6E6.4 0.0 Flg 0 E O
# OUT Y3: set to sink current when OFF else when ON
polarity_invert_A1 6E6.5 0.0 Flg 0 E O
# OUT A1: set to sink current when OFF else when ON
polarity_invert_S3 6E7.2 0.0 Flg 0 E O
# OUT S3: set to SOURCE current when OFF else whn ON
polarity_invert_T3 6E7.3 0.0 Flg 0 E O
# OUT T3: set to SOURCE current when OFF else whn ON
polarity_invert_B2 6E7.4 0.0 Flg 0 E O
# OUT B2: set to sink current when OFF else when ON
polarity_invert_B1 6E7.5 0.0 Flg 0 E O
# OUT B1: set to sink current when OFF else when ON
door_offset_initial 6E8 80.0 A/D 0050 E V
tbofst initial blower bypass door position offset
double_rpm 6EA 0.00 RPM 0000 E*4 V
dblrpm RPM>DBLRPM+DBLENB to calc PW every other cyl/0=off
egr_temp_leadlag_k1 6EC 0.000000 "" 0000 E*65536 B
egrlk1 EGR temp lead/lag filter parameter 1
egr_temp_leadlag_k2 6EE 0.00000 "" 0000 E*4096 B
egrlk2 EGR temp lead/lag filter parameter 2
egr_temp_leadlag_k3 6F0 0.00000 "" 0000 E*4096 B
egrlk3 EGR temp lead/lag filter parameter 3
engine_over_speed_disable 6F2 2500.00 RPM 2710 E*4 E
rpmdfl rpm at which rpm high war lamp is turned off if on
engine_over_speed_enable 6F4 2500.00 RPM 2710 E*4 E
rpmefl rpm at which rpm high warning lamp is turned on
ess_break_tq_base_temp 6F6 90.00 dgC 0750 (E+40)*14.4 V
essbbt Base tmp used to inc. or dec. zero tq. estimate
ess_high_range_clutch_btw_rpm 6F8 1400.00 RPM 15e0 E*4 V
esshrc If abov whn cltchng to neut swtch tran to hgh rng
ess_high_range_neutral_bnd_rpm 6FA 1800.00 RPM 1c20 E*4 V
esshrn If abov whn coasting in neut swtch tran to hgh rng
ess_ideal_engine_rpm 6FC 1400.00 RPM 15e0 E*4 V
essier Ideal RPM used for second chance gear selection
ess_low_range_clutched_btw_rpm 6FE 1200.00 RPM 12c0 E*4 V
esslrc If belw whn cltchng to neut swtch tran to low rng
ess_low_range_neutral_bnd_rpm 700 1200.00 RPM 12c0 E*4 V
esslrn If belw whn coasting in neut swtch tran to low rng
ess_min_trans_rpm 702 63.00 "" 01f8 E*8 V
essmtr The minimum trans RPM needed for ESS functionality
ess_rpm_transition_rate 704 3000.0 RPM/ 012c E/10 V
essrtr Linear trans rate whn movng frm crrnt to reqst RPM
ess_sync_offset 706 -15.00 RPM ffffff88 E*8 V
essso Offset applied to synch. RPM to avoid tooth butt
ess_sync_protection_offset 708 20.00 RPM 00a0 E*8 V
essspo Aids synchrnzr cmpl a rng shft whn put in gr early
ether_pre_load_rpm 70A 1500.00 RPM 1770 E*4 V
eiplmx RPM>eiplmx to allow pre-load at next IGN on
ether_max_hysteresis 70C 200.00 RPM 0320 E*4 V
eimxhy ether injection reenabled when RPM < eimax-eimxhy
ether_min_hysteresis 70E 20.00 RPM 0050 E*4 V
eimnhy ether block inj disabled when RPM < eimin-eimnhy
ex_temp_leadlag_k1 710 0.000000 %@1S 0000 E*65536 V
exllk1 lead/lag filter constants @1sec to compnsate for..
ex_temp_leadlag_k2 712 1.00000 %@1S 1000 E*4096 V
exllk2 ... Exhaust Temp Sensor response time ...
ex_temp_leadlag_k3 714 0.00000 %@1S 0000 E*4096 V
exllk3 ..ExhTmp=K1*LastExhTmp+K2*A/DExhTmp-K3*LastA/DExhT
fan_air_threshold 716 60.97 dgC 05ae (E+40)*14.4 E
atfpwm (AirTemp-atfpwm) sets min FANPWM duty cycle
fan_coolant_threshold 718 84.03 dgC 06fa (E+40)*14.4 E
ctfpwm (CoolantTemp-ctfpwm) sets min FANPWM duty cycle
fan_cooler_threshold 71A 90.00 dgC 0750 (E+40)*14.4 E
itfpwm (InterClrTmp-itfpwm) sets min FANPWM duty cycle
fan_max_speed 71C 2500.00 RPM 2710 E*4 E
fanmax if RPM>fanmax then 2spd fan runs in 1:1 spd mode
fan_min_speed 71E 2400.00 RPM 2580 E*4 E
fanmin RPM<fanmin for 2spd fan to run in 1.4:1 spd mode
fan_oil_threshold 720 110.00 dgC 0870 (E+40)*14.4 E
otfpwm (OilTemp-otfpwm) sets min FANPWM duty cycle
fault_rpm_limit 722 2500.00 RPM 2710 E*4 V
dimxes RPM > dimxes to log an engine overspeed condition
base_air_boi_adv_max 724 155.56 dgC 0b00 (E+40)*14.4 B
boiamx max BASBOI temp w/ 16 steps from AIRMIN to AIRMAX
base_air_boi_adv_min 726 -40.00 dgC 0000 (E+40)*14.4 B
boiamn min BASBOI temp w/ 16 steps from AIRMIN to AIRMAX
filtq_neg_filt_const 728 0.0068 "" 0007 E*1024 V
fltnfc filt const if final tq is less than currnt filt tq
filtq_pos_filt_const 72A 0.0068 "" 0007 E*1024 V
fltpfc filt const if final tq is > than curnt filt tq
fire_mode_rpm_delta 72C 400.00 RPM 0640 E*4 V
ftprpd Press Mode max allowable RPM increase from set RPM
fire_pump_press_analog_gain 72E 0.48877 "" 03e9 E*2048 V
fwppag if set, gain used to bcast aux water pump pressure
fire_pump_press_analog_offset 730 -102.0 A/D ffffff9a E V
fwppao if fwppag set, offset used to bcast aux water p p
firpm_filterconst 732 500.00 RPM 07d0 E*4 V
fimgc RPM ratio filter constant: K=fimgc/RPM
fphi_max_rpm 734 610.00 RPM 0988 E*4 V
fpwrpm RPM < fpwrpm to log fuel press sensor failed high
fphi_min_oil_temp 736 30.00 dgC 03f0 (E+40)*14.4 V
fpwmot oiltemp > fpwmot to log fuel press sensor fail hi
fuel_boi_adv_max 738 70.97 dgC 063e (E+40)*14.4 V
fulmax max FULBOI temp w/ 16 steps from FULMIN to FULMAX
fuel_boi_adv_min 73A 7.01 dgC 02a5 (E+40)*14.4 V
fulmin min FULBOI temp w/ 16 steps from FULMIN to FULMAX
fuel_temp_leadlag_k1 73E 0.000000 %@1S 0000 E*65536 V
ftllk1 lead/lag filter constants @1sec to compnsate for..
fuel_temp_leadlag_k2 740 1.00000 %@1S 1000 E*4096 V
ftllk2 .. Fuel Temp Sensor response time ...
fuel_temp_leadlag_k3 742 0.00000 %@1S 0000 E*4096 V
ftllk3 ..FulTmp=K1*LastFulTmp+K2*A/DFulTmp-K3*LastA/DFulT
fueling_rpm_limit 744 2500.00 RPM 2710 E*4 V
maxrpm RPM > maxrpm then no fuel
gear_ratio_tolerance 746 2.000 RPM/ 0100 E*128 B
dpgrt Allowed variation in gear ratio for a given gear
glowplugs_comp_voltage 748 14.000 VLT 08c0 E*160 E
gpbat glowplug Vbat comp:%DC=min(1,(gpbat/Vbatt)^2)*100%
glowplugs_max_temp 74A 70.97 dgC 063e (E+40)*14.4 V
gptemp OilTemp>gptemp & FTQ & Timer for glow plugs OFF
gov_gainnorm_filterconst 74C 0.1016 % @ 001a E*256 V
gvgnfc GOV gain normalization filter constant @ 25msec
gov_gainnorm_nom_rpm 74E 2000.00 RPM 1f40 E*4 V
gvnmrp GOV gain normalization nominal RPM: =RPM/gvnmrp
gov_lag_filterconst 750 2.0000 % @ 0200 E*256 V
gvlgfc governor lag filter constant @ 1 sec interval
halfeng_max_temp_opt1 752 12.50 dgC 02f4 (E+40)*14.4 V
hemxt1 temp > which to exit half eng mode if heenb set
high_alt_minimum_rpm 754 4095.75 RPM 3fff E*4 V
hamnrp min RPM at which HIGH ALTITUDE TQ limiting allowed
high_alt_rpm_limit 756 2100.00 RPM 20d0 E*4 V
harpmx RPM at which max HIGH ALTITUDE TQ limiting occurs
high_cool_prs_max_rpm 758 1800.00 RPM 1c20 E*4 V
cpmrpm RPM<cpmrpm for coolant press sensor failed high
high_oilp_max_rpm 75A 800.00 RPM 0c80 E*4 V
opwrpm RPM < opwrpm to log oil press sensor failed high
high_oilp_min_oilt 75C 80.00 dgC 06c0 (E+40)*14.4 V
opwmot oiltemp > opwmot to log oil press sensor fail hi
idle_gov_disable_delta 75E 200.00 RPM 0320 E*4 V
idldsb RPM above idle at which idle governor disabled
idle_gov_enable_delta 760 50.00 RPM 00c8 E*4 V
idlenb RPM above idle at which idle governor re-enabled
idle_shut_max_ambt 762 75.00 dgC 0678 (E+40)*14.4 D
isathi for IDLE SHUTDOWN Override: AmbientTemp>ISATHI ...
idle_shut_min_ambt 764 75.00 dgC 0678 (E+40)*14.4 D
isatlo ... .AND. AmbientTemp<ISATLO ...
idle_shut_top_ambt 766 80.00 dgC 06c0 (E+40)*14.4 V
isomxt ... .AND. AmbientTemp<ISOMXT (ATS tamper protectn)
idle_shut_min_oilt 768 40.00 dgC 0480 (E+40)*14.4 V
istmp oiltemp > estmp to allow idle shutdown
idle_speed_lower 76A 600.00 RPM 0960 E*4 E
idlmin Lower limit on idle speed
idle_speed_offset 76C 0.00 RPM 0000 E*4 D
idlofs Customer settable adjustment to idle speed
idle_speed_upper 76E 2500.00 RPM 2710 E*4 O
idlmax Upper limit on idle speed
idle_timeout 770 600.0 SEC 0258 E D
istim IDLE SHUTDOWN time in seconds
idle_warn_time 772 90.0 SEC 005a E V
iswntm IDLE SHUTDOWN Override Warning time-secs CEL flash
inj_cal_nominal_rpm 774 2000.00 RPM 1f40 E*4 V
inmrpm InjCal RPM compensation: InjCal=InjCal*RPM/inmrpm
injector_detect_delay 776 60.0 uSC 0078 E*2 V
irtdly constant delay from actual closure to detection
injector_min_oiltemp 778 30.00 dgC 03f0 (E+40)*14.4 V
rtotmp oiltemp > rtotmp to log rise time too long
injector_min_voltage 77A 11.00 VLT 00b0 E*16 V
rtbat battery volts > rtbat to log RT too short or long
injector_turnoff_delay 77C 0.0000 MSC 0000 E*1000 V
itohlt delay from elect. turn-off to actual end of injctn
injector_upper_limit 77E 1600.0 uSC 0c80 E*2 V
irtcap max actual and max default risetime in MSECs
irt_min_pulse_time 780 200.0 uSC 0190 E*2 V
irtmpt FPW>IRTMPT for RespTime faults & updates
jake_disable_delta 782 200.00 RPM 0320 E*4 V
jbdoff delta RPM above idle at which jake brakes disabled
jake_enable_delta 784 250.00 RPM 03e8 E*4 V
jbdon delta RPM above idle at which jakes reenabled
jake_error_rpm 786 2500.00 RPM 2710 E*4 V
jberpm RPM > jberpm to log jake brake overspeed code
low_gear_hysteresis 788 0.047 R/M 0006 E*128 V
trlhys Act gr rat< trlrat-trlhys to disble lw gr TQ limtg
low_gear_threshold 78A 300.000 R/M 9600 E*128 V
trlrat Act gr rat > trlrat for low gr TQ limitg to trllim
low_gear_torque_limit_ft_lb 78C 65535.0 Ft-l ffff E O
lgtqlm Max torque when low gear torque limiting enabled
low_range_ratio 78E 3.89014 RTO 1f1f E*2048 O
esslrr Low range ratio for ESS transmission type
max_ether_rpm 790 1500.00 RPM 1770 E*4 V
eimax RPM<eimax for ether block OR pre-load injection
max_pulse_width 792 40.0000 DEG 2800 E*256 V
maxpw max allowable pulse width before multiplier
max_rpm_droop 794 150.00 RPM 0258 E*4 V
maxdrp max allowable limiting speed droop
minimum_running_rpm 796 60.00 RPM 00f0 E*4 V
minrpm RPM < minrpm then engine not running
min_ether_rpm 798 60.00 RPM 00f0 E*4 V
eimin RPM > eimin for ether block injection
min_turbo_speed_sensed 79A 0.0 RPM 0000 E/128 V
mintss Minimum turbo speed needed to indicate valid TSS
mf_accel_rate_filterconst 79C 0.0098 "" 000a E*1024 B
mfacfc misfire rpm acceleration rate filter constant
mf_boi_filterconst 79E 0.0254 "" 001a E*1024 V
mfboif misfire BOI offset filter constant
mf_disable_temp 7A0 30.00 dgF 03f0 (E+40)*14.4 V
mfdist exit maj misfr whn weighted eng temp > mfdist
mf_major_accel_threshold 7A2 750.00 rpm/ 0bb8 E*4 B
mfmjat major misfire if accel rate > mfmjat
mf_minor_accel_exit 7A4 200.00 rpm/ 0320 E*4 V
mfmnae exit mnr misf whn mfmnde<accl rt<mfmnae for mfmnet
mf_minor_accel_threshold 7A6 300.00 rpm/ 04b0 E*4 B
mfmnat minor misfire if accel rate > mfmnat
mm_afrs_max_rpm 7A8 1500.00 RPM 1770 E*4 V
mmafmr RPM below which air filt. is dirty is AFRS>scldhi
mm_ofrs_min_engine_temp 7AA 71.11 dgC 0640 (E+40)*14.4 V
mmomnt Eng temp above which a drty oil filt can be detctd
noise_boi_cool_temp 7AC 65.00 dgC 05e8 (E+40)*14.4 B
nboict Minimum coolant temp to replace BOI with cal
noise_max_gear_ratio 7AE 140.000 Rto 4600 E*128 V
nmaxvr RPM/MPH < nmaxvr to enable noise control
noise_min_gear_ratio 7B0 40.000 Rto 1400 E*128 V
nminvr RPM/MPH > nminvr to enable noise control
noise_rpm_delta 7B2 100.00 RPM 0190 E*4 V
nrpdel noise cortrol RPM range = .67*ratedRPM +/- NRPDEL
noise_transition_gear_ratio 7B4 93.000 RPM/ 2e80 E*128 B
nctgr Noise cont trans gr rat to high gr distance
nox_adapt_coolant_temp 7B6 -40.00 dgC 0000 (E+40)*14.4 V
nxapct if ClntTmp<nxapct AND PkBrk then full NXDBOI adv
nox_adapt_virtual_gear 7B8 0.000 R/M 0000 E*128 B
nxvgav RPM/MPH < nxvgav then full NXDBOI advance
nox_filterconst 7BA 0.0088 % @ 0009 E*1024 V
nxapfc newAT=oldAT+nxapfc*(max(0,(deltaRPM/nxsmp))-oldAT)
nox_steady_lower_limit 7BC 8.50 R/S 0022 E*4 B
nxsll if NXASDY set AND ATP<nxsll then full NXDBOI adv
nox_steady_upper_limit 7BE 8.75 R/S 0023 E*4 B
nxsul if NXASDY set AND ATP>nxsul then no NXDBOI adv
nox_trans_lower_limit 7C0 4095.50 R/S 3ffe E*4 B
nxtll if NXATRN set AND ATP<nxtll then no NXDBOI adv
nox_trans_upper_limit 7C2 4095.75 R/S 3fff E*4 B
nxtul if NXATRN set AND ATP>nxtul then full NXDBOI adv
oi_ftq_filt_const 7C4 0.1992 % @ 0033 E*256 V
oiftfc OI TASSTQ filter: new=old+filt*(new-old) @ 25msec
oil_temp_fan1_on 7C6 112.99 dgC 089b (E+40)*14.4 E
otf1on OilTemp>OTF1ON for single/.5 dual/high spd FANs
oil_temp_fan2_on 7C8 110.00 dgC 0870 (E+40)*14.4 E
otf2on OilTemp>OTF2ON to enable low speed of 2 speed FAN
oil_temp_fan_off 7CA 104.03 dgC 081a (E+40)*14.4 E
otoff oil temp < otoff to turn FanOut#1+#2 off
otp_tlf_recovery_fconst 7CC 1.0000 unit 0400 E*1024 V
ottrfc dampens tco and exh temp tq limit recovery rampup
override_idle_rpm 7CE 450.00 RPM 0708 E*4 V
minorp min ESS idle override RPM for break torque
override_max_rpm 7D0 2500.00 RPM 2710 E*4 V
maxorp maximum requestable RPM from ABS or transmission
park_brake_adv_max 7D2 80.00 degC 06c0 (E+40)*14.4 V
pbadmx the max of park_brake_offset_boi table
park_brake_adv_min 7D4 0.00 degC 0240 (E+40)*14.4 V
pbadmn the min of park_brake_offset_boi table
park_brake_temp_weighting_pid0 7D6 110.0 unit 006e E V
pbtwp0 eng temp PID used for determ temp BOI advance
park_brake_temp_weighting_pid1 7D8 172.0 unit 00ac E V
pbtwp1 eng temp PID used for determ temp BOI advance
pss_range1_limit_rpm 7DA 1800.00 RPM 1c20 E*4 D
psrpm1 PROG SHIFT: RPM>psrpm1 to limit rate RPM rise rng1
pss_range1_max_rpm 7DC 1800.00 RPM 1c20 E*4 D
psmxr1 PROG SHIFT: max RPM allowed in range 1
pss_range1_rise_rate 7DE 33.0 R/S 0021 E V
psris1 PROG SHIFT: max rate of RPM rise in range 1
pss_range2_limit_rpm 7E0 1800.00 RPM 1c20 E*4 D
psrpm2 PROG SHIFT: RPM>psrpm2 to limit rate RPM rise rng2
pss_range2_max_rpm 7E2 1800.00 RPM 1c20 E*4 D
psmxr2 PROG SHIFT: max RPM allowed in range 2
pss_range2_rise_rate 7E4 25.0 R/S 0019 E V
psris2 PROG SHIFT: max rate of RPM rise in range 2
pss_range3_max_rpm 7E6 1800.00 RPM 1c20 E*4 D
psrpm3 PROG SHIFT: max RPM allowed in range 3
pto_alt_minimum_rpm 7E8 600.00 RPM 0960 E*4 D
ptmin2 alt min PTO setRPM selected by grounding DigIN #16
pto_gain_divisor 7EA 775.0 A/D 0307 E E
ptodiv PTO A/D counts from min to max PTO RPM
pto_droop 7EC 0.00 RPM 0000 E*4 D
ptodrp PTO: max no load RPM above rated speed in PTO mode
pto_maximum_rpm 7EE 1600.00 RPM 1900 E*4 D
ptmaxv maximum PTO set RPM
pto_minimum_rpm 7F0 600.00 RPM 0960 E*4 D
ptminv minimum PTO set RPM
pw_fudge_factor 7F2 1.0000 MLT 0100 E*256 F
pwmult Final PW = pwmult * Provisional PW (HP correction)
pw_routine_eoe_calc_latency 7F4 0.0 usec 0000 E V
pwelat calc latency from pw irq to eoe write to ASIC
rpm_droop 7F6 125.00 RPM 01f4 E*4 D
rpmdrp DROOP: max no load RPM above rated speed on TPS
rpm_gov_disable_delta 7F8 300.00 RPM 04b0 E*4 V
ergdsb (rated RPM-actual RPM)>ergdsb then RPM gov disabld
rpm_gov_enable_delta 7FA 250.00 RPM 03e8 E*4 V
ergenb (rated RPM-actual RPM)<ergenb then RPM gov enabled
rpm_table_min 7FC 150.0 RPM 0096 E V
rtblmn Minimum RPM column value for all RPM tables
runsignal_disable_rpm 7FE 60.00 RPM 00f0 E*4 E
rnsdsb STARTER INHIBIT: DOutX OFF until RPM>rnsenb, . . .
runsignal_enable_rpm 800 500.00 RPM 07d0 E*4 E
rnsenb STARTER INHIBIT: . .then DOutX ON until RPM<rnsdsb
sa_filter_constant 802 0.000549 %@1s 0012 E*32768 V
mpgfc FuelEcon MPG filter: new=old+fc*(inst-old) @ 1 sec
shutdn_coolant_temp 804 107.01 dgC 0845 (E+40)*14.4 E
discot coolant temp > discot then stop engine condition
shutdn_cylhead_temp 806 244.38 dgC 0fff (E+40)*14.4 V
discht cylinder head temp > discht then stop eng conditn
shutdn_ex_temp 808 565.00 dgC 2208 (E+40)*14.4 V
disext exhaust temp > disext then stop engine condition
shutdn_inner_temp 80A 99.03 dgC 07d2 (E+40)*14.4 E
disict InnerCooler Temp > DISICT then stop eng condition
shutdn_min_rpm 80C 2500.00 RPM 2710 E*4 E
sermin min PTO RPM during stop or slow engine condition
shutdn_oil_temp 80E 120.97 dgC 090e (E+40)*14.4 E
disolt oil temp > disolt then stop engine condition
shutdn_tco_temp 810 1097.71 dgC 3fff (E+40)*14.4 V
tcotth tco temp > tcotth then stop engine condition
shutdn_trans_temp 812 244.38 dgC 0fff (E+40)*14.4 V
distrt trans temp > distrt then stop engine condition
single_turbo_delay_min_boost 814 0.00 KPA 0000 E*2.31985 B
stdmb boost>stdmb then dtstd used to sw from dual to sgl
single_turbo_engrpm_hyst 816 50.00 RPM 00c8 E*4 V
sterhy hysteresis for switching from dual to single turbo
single_turbo_max_engrpm 818 4095.75 RPM 3fff E*4 B
stmxer max eng RPM before switching from single to dual
single_turbo_max_tcrpm 81A 0.0 RPM 0000 E/128 B
stmxtr Max turbo RPM before switching from single to dual
single_turbo_maxltq_min 81C 150.0 rpm 0096 E V
stmlmn Min rpm val usd to define range for stmxtq
single_turbo_smoke_cntl_tq_add 81E 0.000 %tq 0000 E*20.47 V
stscta if in single turbo mode add to episct
single_turbo_tcrpm_hyst 820 24960.0 RPM 00c3 E/128 V
strphy Turbo RPM hyst when switching from dual to single
snl_cel_fault_expiration_hours 822 0.0 hrs 0000 E V
snlfxh fault duration after which CEL/SNL turns on; 0=dis
snl_air_filter_diff_press 824 32767.0 bitm 7fff E V
snlafp FMI CEL/SNL lamp activation bitmapping for PID107
snl_ambient_air_temp 826 32767.0 bitm 7fff E V
snlaat FMI CEL/SNL lamp activation bitmapping for PID171
snl_fire_pump_pressure 828 32767.0 bitm 7fff E V
snlfpp FMI CEL/SNL lamp activation bitmapping for PID173
snl_fmi_all_other_faults 82A 32767.0 bitm 7fff E V
snlaof FMI CEL/SNL act bitmapping for all other faults
snl_fmi_backup_battery 82C 32767.0 bitm 7fff E V
snlbpb FMI CEL/SNL lamp activation bitmapping for SID214
snl_fmi_barometric_pressure 82E 32767.0 bitm 7fff E V
snlbrp FMI CEL/SNL lamp act. bitmapping for PID48 or 108
snl_fmi_battery_voltage 830 32767.0 bitm 7fff E V
snlbtv FMI CEL/SNL lamp activation bitmapping for PID168
snl_fmi_boost_pressure 832 32767.0 bitm 7fff E V
snlbsp FMI CEL/SNL lamp activation bitmapping for PID102
snl_fmi_calibration_memory 834 32767.0 bitm 7fff E V
snlclm FMI CEL/SNL lamp activation bitmapping for SID253
snl_fmi_coolant_level 836 32767.0 bitm 7fff E V
snlcol FMI CEL/SNL lamp act. bitmapping for PID111 and 16
snl_fmi_coolant_pressure 838 32767.0 bitm 7fff E V
snlcop FMI CEL/SNL lamp act. bitmapping for PID109 or 20
snl_fmi_coolant_temperature 83A 32767.0 bitm 7fff E V
snlcot FMI CEL/SNL lamp activation bitmapping for PID110
snl_fmi_crankcase_pressure 83C 32767.0 bitm 7fff E V
snlckp FMI CEL/SNL lamp act. bitmapping for PID101 or 153
snl_fmi_engine_speed 83E 32767.0 bitm 7fff E V
snlens FMI CEL/SNL lamp activation bitmapping for PID190
snl_fmi_exhaust_backpressure 840 32767.0 bitm 7fff E V
snlebp FMI CEL/SNL lamp activation bitmapping for PID81
snl_fmi_exhaust_temperature 842 32767.0 bitm 7fff E V
snlext FMI CEL/SNL lamp activation bitmapping for PID173
snl_fmi_fuel_pressure 844 32767.0 bitm 7fff E V
snlflp FMI CEL/SNL lamp activation bitmapping for PID94
snl_fmi_fuel_temperature 846 32767.0 bitm 7fff E V
snlflt FMI CEL/SNL lamp activation bitmapping for PID174
snl_fmi_injection_pressure 848 32767.0 bitm 7fff E V
snlijp FMI CEL/SNL lamp act. bitmapping for PID164
snl_fmi_injector_response_time 84A 32767.0 bitm 7fff E V
snlirt FMI CEL/SNL lamp act. bitmapping for irt SIDs
snl_fmi_intercooler_clnt_temp 84C 32767.0 bitm 7fff E V
snlict FMI CEL/SNL lamp activation bitmapping for PID52
snl_fmi_j1708_data_link 84E 32767.0 bitm 7fff E V
snljdl FMI CEL/SNL lamp activation bitmapping for SID250
snl_fmi_manifold_air_temp 850 32767.0 bitm 7fff E V
snlmat FMI CEL/SNL lamp activation bitmapping for PID172
snl_fmi_manifold_pressure 852 32767.0 bitm 7fff E V
snlmfp FMI CEL/SNL lamp activation bitmapping for PID106
snl_fmi_oil_filter_diff_press 854 32767.0 bitm 7fff E V
snlofp FMI CEL/SNL lamp activation bitmapping for PID99
snl_fmi_oil_pressure 856 32767.0 bitm 7fff E V
snlolp FMI CEL/SNL lamp act. bitmapping for PID100 or 19
snl_fmi_oil_temperature 858 32767.0 bitm 7fff E V
snlolt FMI CEL/SNL lamp activation bitmapping for PID175
snl_fmi_percent_tps 85A 32767.0 bitm 7fff E V
snlptp FMI CEL/SNL lamp activation bitmapping for PID91
snl_fmi_proprietary_data_link 85C 32767.0 bitm 7fff E V
snlpdl FMI CEL/SNL lamp activation bitmapping for SID248
snl_fmi_pto_set_speed 85E 32767.0 bitm 7fff E V
snlpss FMI CEL/SNL lamp activation bitmapping for PID187
snl_fmi_pwm_1 860 32767.0 bitm 7fff E V
snlpw1 FMI CEL/SNL lamp activation bitmapping for SID57
snl_fmi_pwm_2 862 32767.0 bitm 7fff E V
snlpw2 FMI CEL/SNL lamp activation bitmapping for SID58
snl_fmi_pwm_3 864 32767.0 bitm 7fff E V
snlpw3 FMI CEL/SNL lamp activation bitmapping for SID59
snl_fmi_srs_trs 866 32767.0 bitm 7fff E V
snlsts FMI CEL/SNL lamp activation bitmapping for SID21
snl_fmi_turbo_speed 868 32767.0 bitm 7fff E V
snltrs FMI CEL/SNL lamp activation bitmapping for PID103
snl_fuel_filter_diff_press 86A 32767.0 bitm 7fff E V
snlffp FMI CEL/SNL lamp activation bitmapping for PID95
start_disable_delta 86C 0.00 RPM 0000 E*4 V
smiddl delta RPM above idle to switch start to run mode
start_enable_rpm 86E 300.00 RPM 04b0 E*4 V
smback RPM<smback then switch from run back to start mode
steady_egr_max_rpm 870 4095.75 rpm 3fff E*4 B
segrxr max engine speed for EGR win when in steady BOI
steady_egr_min_rpm 872 0.00 rpm 0000 E*4 B
segrnr min engine speed for EGR win when in steady BOI
steady_egr_rpm_hyst 874 0.00 rpm 0000 E*4 B
segrrh engine speed hyst for EGR win when in steady BOI
t2_dwn_timer_offset_rpm 876 200.00 RPM 0320 E*4 V
astdto Timer based RPM offset for anti-hunt after upshift
t2_hyst_dwn_rpm 878 50.00 RPM 00c8 E*4 V
asthdr RPM offset to reset downshift pts after an upshif
t2_hyst_up_rpm 87A 50.00 RPM 00c8 E*4 V
asthur RPM offset to reset upshift pts after a downshift
t2_min_output_spd 87C 10.00 RPM 0028 E*4 V
astmos Min output shaft speed to disable T2 when IGN OFF
t2_skid_limit 87E 1000.0 RPM/ 0064 E/10 V
astskl Deceleration limit to recognize a skid condition
t2_sync_time 880 3.000 SEC 0078 E*40 V
astsct Time allowed for confirming gear engagement
t2_up_timer_offset_rpm 882 100.00 RPM 0190 E*4 V
astuto RPM offset for anti-hunt after downshift
tas_crank_end_rpm 884 450.00 RPM 0708 E*4 V
tascer starter engaged until RPM>TASCER during auto-start
tas_crank_min_rpm 886 150.00 RPM 0258 E*4 V
tascmr RPM>TASCMR in secs<TASCRT to continue auto-start
tas_crank_voltage 888 12.2 VLT 007a E*10 V
tascvt Vbat<TASCVT for auto-start if ISD+interlocks+alarm
tas_idle_gallons_per_hour 88A 0.580 GPH 003a E*100 V
tasgph estimated fast idle fuel consumption in gal/hr
tas_min_brake_rpm 88C 10.00 RPM 0028 E*4 V
tasmbr Min RPM allowed with jakes on for OI eng shutdn
tas_min_shutdown_voltage 88E 12.5 VLT 007d E*10 V
tasmsv Vbat>TASMSV for IdleShutDown if cab+oil temp OK
tas_rpm_summer 890 1100.00 RPM 1130 E*4 V
tassum setRPM=TASSUM if ambtemp>TASTMP after auto-start
tas_rpm_winter 892 1100.00 RPM 1130 E*4 V
taswin setRPM=TASWIN if ambtemp<TASTMP after auto-start
tco_temp_leadlag_k1 894 0.000000 %@1S 0000 E*65536 V
tcolk1 lead/lag filter constants @1sec to compnsate for..
tco_temp_leadlag_k2 896 1.00000 %@1S 1000 E*4096 V
tcolk2 .. TCO Temp Sensor response time ...
tco_temp_leadlag_k3 898 0.00000 %@1S 0000 E*4096 V
tcolk3 ..TCOTmp=K1*LastTCOTmp+K2*A/DTCOTmp-K3*LastA/DTCOT
tooth_to_boe_min_time 89A 0.0 usec 0000 E B
iboemt calc latency time from tooth iterrupt to ASIC writ
top_gear_1_min_detect_time 89C 20.0 SEC 0014 E B
dptg1t Top gear minus 1 debounce time
trans_ret_cool_temp 89E 85.00 dgC 0708 (E+40)*14.4 E
trctmp CoolTmp>TRCTMP to enable FAN(s) w/ TRANs RTRDR ON
transmission_ratio 8A0 1.000 RTO 0064 E*100 D
trnrat VSS: Final drive ratio
turbo_fault_min_rpm 8A2 0.00 RPM 0000 E*4 V
tfmrpm min RPM to allow turbo overspeed/overboost fault
turbo_min_oilt 8A4 -40.00 dgC 0000 (E+40)*14.4 V
tboilt oil temp<tboilt fixed position for turbo/blwr byps
turbo_overboost_fault_hyst 8A6 3.88 KPA 0009 E*2.31985 V
tbobhy Boost pressure hyst to clear overboost fault
turbo_overboost_int_gain 8A8 0.598 %TQ/ 0042 E*110.343 V
tbobig turbo overboost integral gain
turbo_overboost_prop_gain 8AA 0.598 %TQ/ 0042 E*110.343 V
tbobpg turbo overboost proportional gain
turbo_overbst_max_press_delta 8AC 6.03 KPA 000e E*2.31985 V
tbobpd control turbo bst if turbo bst >= tbobpd + tbobfp
turbo_overspeed_fault_hyst 8AE 2944.0 RPM 0017 E/128 V
tboshy Turbo speed RPM hysteresis to clear overspd fault
turbo_overspeed_max_delta 8B0 2944.0 RPM 0017 E/128 V
tbosmd Turbo spd controlled if spd >= tbosmd + tbosfs
turbo_speed_boost_threshold 8B2 400.03 KPA 03a0 E*2.31985 V
tbspbt boost must be > tbspbt to determine if a TSS fault
twin_sync_max_diff 8B4 100.00 RPM 0190 E*4 V
twrpmd max RPM delta to allow exit from twin eng RPM sync
twin_sync_min_rpm 8B6 300.00 RPM 04b0 E*4 V
twminr RPM>twminr to allow twin engine RPM sync mode
upc_6n4c 8B8 125.0 DEC 007d E E
pc6n4c Calibration's 6N4C Application Code
upc_6n4d 8BA 7013.0 DEC 1b65 E B
pc6n4d 6N4D Engine Horsepower Family
upc_6n4r_r0 8BC 7230.0 DEC 1c3e E B
p6n4r0 6N4R Engine Horsepower Rating
upc_6n4r_r1 8BE 7231.0 DEC 1c3f E B
p6n4r1 6N4R Engine Horsepower Rating
upc_6n4r_r2 8C0 7232.0 DEC 1c40 E B
p6n4r2 6N4R Engine Horsepower Rating
upc_6n4s 8C2 6063.0 DEC 17af E B
pc6n4s 6N4S Shared calibrations
variable_speed_gov_off 8C4 100.0 CNTs 0064 E V
vsgoff VSG A/D counts to turn VSG active output off
variable_speed_gov_on 8C6 140.0 CNTs 008c E V
vsgdon VSG A/D counts to turn VSG active output on
vgr_filterconst 8C8 0.0195 % @ 0005 E*256 V
vrppfc virtual gear ratio filter constant
vnt_overall_gain 8CA 1.000 "" 0064 E*100 B
vntogn overall gain for boost and EGR PID ctrl algorithm
vnt_overspeed_deriv_gain 8CC 0.0000000 "" 0000 E*1000000 B
vnttdg derivative gain for turbo speed ctrl
vnt_overspeed_integ_gain 8CE 0.00000000 "" 0000 E*10000000 B
vnttig integral gain for turbo speed ctrl
vnt_overspeed_prop_gain 8D0 0.0000000 "" 0000 E*1000000 B
vnttpg proportional gain for turbo speed ctrl
vss_fail_detect_rpm 8D2 1500.00 RPM 1770 E*4 V
vsfes RPM>vsfes to log VSS failed code
vss_tamp_drpm 8D4 400.0 R/S 0190 E V
vsstdr RPM>vsstdr to reset VSS tampering logic
vss_tamp_drpm_filt 8D6 0.0508 Tau 000d E*256 V
vsstdf change in RPM filter constant for VSS tampering
vss_tamp_rpm_filt 8D8 0.1016 Tau 001a E*256 V
vsstrf RPM filter constant for VSS tampering
vss_tamp_spd_filt 8DA 0.1016 Tau 001a E*256 V
vsstsf VSS filter constant for VSS tampering
vss_tamp_vgr_capt_time 8DC 4.000 SEC 00a0 E*40 V
vsstct SECs after reset before capturing VGR,RPM,VSS data
vss_tamp_vgr_filt 8DE 0.1016 Tau 001a E*256 V
vsstvf VGR filter constant for VSS tampering
wheel_revs_per_mile 8E0 508.0 Revs 13d8 E*10 D
trrpmi VSS: Tire revs per mile

NAME: acs_digital_limit_torque ADDR: 8E2 UNT: "" OWN: E CODE: actqlt


EQN: E/60
TRQlim=MIN(TRQ,dtqlmt,actqlt) if DinX=14 & Gnd'd
RPM| HEX| ""
--------------------------------
150.0| ff| 15300.0
300.0| ff| 15300.0
450.0| ff| 15300.0
600.0| ff| 15300.0
750.0| ff| 15300.0
900.0| ff| 15300.0
1050.0| ff| 15300.0
1200.0| ff| 15300.0
1350.0| ff| 15300.0
1500.0| ff| 15300.0
1650.0| ff| 15300.0
1800.0| ff| 15300.0
1950.0| ff| 15300.0
2100.0| ff| 15300.0
2250.0| ff| 15300.0
2400.0| ff| 15300.0
2550.0| ff| 15300.0

NAME: air_temp_offset_boi ADDR: 8F3 UNT: "" OWN: B CODE: airboi


EQN: E*4
delta BOI as a f(air temperature)
dgC| HEX| ""
--------------------------------
-9.0| 22| 8.50
-6.0| 22| 8.50
-3.0| 20| 8.00
-0.0| 1e| 7.50
3.0| 1d| 7.25
6.0| 1c| 7.00
9.0| 1a| 6.50
12.0| 19| 6.25
15.0| 18| 6.00
18.0| 12| 4.50
21.0| 0d| 3.25
24.0| 08| 2.00
27.0| 00| 0.00
30.0| 00| 0.00
33.0| 00| 0.00
36.0| 00| 0.00
39.0| 00| 0.00

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
alternate_password 904 "0BDCPD" V
altpw Factory Password - used to recover lost password
anti_theft_password 90A " " V
atpass Anti-theft protection password

NAME: aux_temp_tq_correction ADDR: 911 UNT: "" OWN: B CODE: axttqc


EQN: E*128
TQ correction based on temp. chosen by axttcp
dgC| HEX| ""
--------------------------------
-40.0| 80| 1.000
-27.8| 80| 1.000
-15.6| 80| 1.000
-3.3| 80| 1.000
8.9| 80| 1.000
21.1| 80| 1.000
33.3| 80| 1.000
45.6| 80| 1.000
57.8| 80| 1.000
70.0| 80| 1.000
82.2| 80| 1.000
94.4| 80| 1.000
106.7| 80| 1.000
118.9| 80| 1.000
131.1| 80| 1.000
143.3| 80| 1.000
155.6| 80| 1.000

NAME: baro_nox_1min_limit_col ADDR: 922 UNT: "" OWN: V CODE: bx1mlc


EQN: E*255
1min load avg > which BARBOI may be adj by bnaadj
dgC| HEX| ""
--------------------------------
0.0| ff| 1.0000
5.0| e5| 0.8980
10.0| d9| 0.8510
15.0| cc| 0.8000
20.0| bf| 0.7490
25.0| b2| 0.6980
30.0| 99| 0.6000
35.0| 8c| 0.5490
40.0| 80| 0.5020
45.0| 73| 0.4510
50.0| 66| 0.4000
55.0| 66| 0.4000
60.0| 66| 0.4000
65.0| 00| 0.0000
70.0| 00| 0.0000
75.0| 00| 0.0000
80.0| 00| 0.0000

NAME: baro_offset_boi ADDR: 933 UNT: "" OWN: B CODE: barboi


EQN: E*4
delta BOI as a f(barometric pressure)
Baro-kPa| HEX| ""
--------------------------------
62.5| 28| 10.00
64.5| 28| 10.00
66.5| 28| 10.00
68.5| 28| 10.00
70.5| 28| 10.00
72.5| 28| 10.00
74.5| 28| 10.00
76.5| 20| 8.00
78.5| 18| 6.00
80.4| 10| 4.00
82.4| 10| 4.00
84.4| 10| 4.00
86.4| 10| 4.00
88.4| 08| 2.00
90.4| 00| 0.00
92.4| 00| 0.00
94.4| 00| 0.00

NAME: base_vnt_boost ADDR: 944 UNT: "" OWN: B CODE: bvntbs


EQN: E/1.72425
desired turbo boost pressure for base BOI op

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
X 300.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
I 450.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
S 600.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 750.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
R 900.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
P 1050.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
M 1200.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 1350.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1 1500.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
7 1650.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1800.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1950.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2100.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2250.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2400.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2550.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 00 00 00 00 00
00 00 00
X 300.0 | 00 00 00 00 00 00
00 00 00
I 450.0 | 00 00 00 00 00 00
00 00 00
S 600.0 | 00 00 00 00 00 00
00 00 00
_ 750.0 | 00 00 00 00 00 00
00 00 00
R 900.0 | 00 00 00 00 00 00
00 00 00
P 1050.0 | 00 00 00 00 00 00
00 00 00
M 1200.0 | 00 00 00 00 00 00
00 00 00
_ 1350.0 | 00 00 00 00 00 00
00 00 00
1 1500.0 | 00 00 00 00 00 00
00 00 00
7 1650.0 | 00 00 00 00 00 00
00 00 00
1800.0 | 00 00 00 00 00 00
00 00 00
1950.0 | 00 00 00 00 00 00
00 00 00
2100.0 | 00 00 00 00 00 00
00 00 00
2250.0 | 00 00 00 00 00 00
00 00 00
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: boi_cold_advance ADDR: 9DD UNT: "" OWN: B CODE: cboiad


EQN: E*4
BOI advance - function weighted air and oil temp
dgC| HEX| ""
--------------------------------
-9.0| 22| 8.50
-6.0| 22| 8.50
-3.0| 20| 8.00
-0.0| 1e| 7.50
3.0| 1d| 7.25
6.0| 1c| 7.00
9.0| 1a| 6.50
12.0| 19| 6.25
15.0| 18| 6.00
18.0| 12| 4.50
21.0| 0d| 3.25
24.0| 08| 2.00
27.0| 00| 0.00
30.0| 00| 0.00
33.0| 00| 0.00
36.0| 00| 0.00
39.0| 00| 0.00

NAME: boost_sstate_output ADDR: 9EE UNT: "" OWN: B CODE: vntsso


EQN: E*2
ff ss %dc for VNT vanes during boost pressure ctrl

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
X 300.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
I 450.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
S 600.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 750.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
R 900.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
P 1050.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
M 1200.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 1350.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1 1500.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
7 1650.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1800.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1950.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2100.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2250.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2400.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2550.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 00 00 00 00 00
00 00 00
X 300.0 | 00 00 00 00 00 00
00 00 00
I 450.0 | 00 00 00 00 00 00
00 00 00
S 600.0 | 00 00 00 00 00 00
00 00 00
_ 750.0 | 00 00 00 00 00 00
00 00 00
R 900.0 | 00 00 00 00 00 00
00 00 00
P 1050.0 | 00 00 00 00 00 00
00 00 00
M 1200.0 | 00 00 00 00 00 00
00 00 00
_ 1350.0 | 00 00 00 00 00 00
00 00 00
1 1500.0 | 00 00 00 00 00 00
00 00 00
7 1650.0 | 00 00 00 00 00 00
00 00 00
1800.0 | 00 00 00 00 00 00
00 00 00
1950.0 | 00 00 00 00 00 00
00 00 00
2100.0 | 00 00 00 00 00 00
00 00 00
2250.0 | 00 00 00 00 00 00
00 00 00
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: grp_lockout_perms ADDR: A87 UNT: Flg OWN: O CODE: comgrp


EQN: E
bit mapped DDR feature reprogam lockout per 62T35
Elements| HEX| Flg
--------------------------------
1| 00| 0.0
2| 00| 0.0
3| 00| 0.0
4| 00| 0.0

NAME: cool_temp_offset_boi ADDR: A8B UNT: "" OWN: B CODE: colboi


EQN: E*4
delta BOI as a f(coolant temperature)
dgC| HEX| ""
--------------------------------
-9.0| 22| 8.50
-4.7| 22| 8.50
-0.4| 20| 8.00
3.9| 1e| 7.50
8.2| 1d| 7.25
12.5| 1c| 7.00
16.9| 1a| 6.50
21.2| 19| 6.25
25.5| 18| 6.00
29.8| 17| 5.75
34.1| 14| 5.00
38.4| 14| 5.00
42.7| 10| 4.00
47.1| 10| 4.00
51.4| 0c| 3.00
55.7| 08| 2.00
60.0| 00| 0.00

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
customer_password A9C "0000" V
cuspw 4 byte PASSWORD req'd to change Customer Option(s)

NAME: data_hub_mids ADDR: AA0 UNT: MIDs OWN: V CODE: hubmap


EQN: E
MIDs (values < 128) supported by Data Hub
Elements| HEX| MIDs
--------------------------------
1| 00| 0.0
2| 00| 0.0
3| 00| 0.0
4| 00| 0.0
5| 00| 0.0
6| 00| 0.0
7| 00| 0.0
8| 00| 0.0
9| 00| 0.0
10| 00| 0.0
11| 00| 0.0
12| 00| 0.0
13| 00| 0.0
14| 00| 0.0
15| 00| 0.0
16| 00| 0.0
17| 00| 0.0
18| 00| 0.0
19| 00| 0.0
20| 00| 0.0
21| 00| 0.0
22| 00| 0.0
23| 00| 0.0
24| 00| 0.0
25| 00| 0.0
26| 00| 0.0
27| 00| 0.0
28| 00| 0.0
29| 00| 0.0
30| 00| 0.0
31| 00| 0.0
32| 00| 0.0

NAME: desired_boost ADDR: AC0 UNT: "" OWN: V CODE: deskpf


EQN: (E-86.21)*1.15992
blwr bypass desired boost press. table f(RPM,load)

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 305.2 305.2 305.2 305.2 305.2 305.2
305.2 305.2 305.2
X 300.0 | 305.2 305.2 305.2 305.2 305.2 305.2
305.2 305.2 305.2
I 450.0 | 201.7 207.8 212.1 222.4 227.6 232.8
237.1 242.3 305.2
S 600.0 | 100.0 110.3 119.8 139.7 150.0 160.4
169.8 180.2 305.2
_ 750.0 | 100.0 110.3 119.8 139.7 150.0 160.4
172.4 185.4 305.2
R 900.0 | 100.0 110.3 119.8 139.7 150.0 160.4
175.0 189.7 305.2
P 1050.0 | 100.0 105.2 119.8 135.4 148.3 160.4
175.9 193.1 305.2
M 1200.0 | 100.0 100.0 119.8 130.2 145.7 160.4
176.7 195.7 305.2
_ 1350.0 | 100.0 100.0 114.7 122.4 135.4 149.1
166.4 183.6 305.2
1 1500.0 | 100.0 100.0 110.3 114.7 123.3 138.8
155.2 170.7 305.2
7 1650.0 | 100.0 100.0 107.8 114.7 127.6 142.2
160.4 175.9 305.2
1800.0 | 100.0 100.0 105.2 114.7 132.8 144.8
162.9 180.2 305.2
1950.0 | 100.0 100.0 105.2 119.8 131.9 152.6
172.4 214.7 305.2
2100.0 | 100.0 100.0 105.2 125.0 130.2 160.4
180.2 250.0 305.2
2250.0 | 201.7 201.7 205.2 214.7 217.3 231.9
242.3 277.6 305.2
2400.0 | 305.2 305.2 305.2 305.2 305.2 305.2
305.2 305.2 305.2
2550.0 | 305.2 305.2 305.2 305.2 305.2 305.2
305.2 305.2 305.2

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | fe fe fe fe fe fe
fe fe fe
X 300.0 | fe fe fe fe fe fe
fe fe fe
I 450.0 | 86 8d 92 9e a4 aa
af b5 fe
S 600.0 | 10 1c 27 3e 4a 56
61 6d fe
_ 750.0 | 10 1c 27 3e 4a 56
64 73 fe
R 900.0 | 10 1c 27 3e 4a 56
67 78 fe
P 1050.0 | 10 16 27 39 48 56
68 7c fe
M 1200.0 | 10 10 27 33 45 56
69 7f fe
_ 1350.0 | 10 10 21 2a 39 49
5d 71 fe
1 1500.0 | 10 10 1c 21 2b 3d
50 62 fe
7 1650.0 | 10 10 19 21 30 41
56 68 fe
1800.0 | 10 10 16 21 36 44
59 6d fe
1950.0 | 10 10 16 27 35 4d
64 95 fe
2100.0 | 10 10 16 2d 33 56
6d be fe
2250.0 | 86 86 8a 95 98 a9
b5 de fe
2400.0 | fe fe fe fe fe fe
fe fe fe
2550.0 | fe fe fe fe fe fe
fe fe fe

NAME: digital_limit_torque ADDR: B59 UNT: "" OWN: B CODE: dtqlmt


EQN: E*2.55
TRQlim=MIN(TRQ,dtqlmt,actqlt) if DinX=14 & Gnd'd
RPM| HEX| ""
--------------------------------
150.0| ff| 100.00
300.0| ff| 100.00
450.0| ff| 100.00
600.0| ff| 100.00
750.0| ff| 100.00
900.0| ff| 100.00
1050.0| ff| 100.00
1200.0| ff| 100.00
1350.0| ff| 100.00
1500.0| ff| 100.00
1650.0| ff| 100.00
1800.0| ff| 100.00
1950.0| ff| 100.00
2100.0| ff| 100.00
2250.0| ff| 100.00
2400.0| ff| 100.00
2550.0| ff| 100.00

NAME: disable_ddec_pages ADDR: B6A UNT: N/A OWN: V CODE: dispag


EQN: E
2bit flgs to en/dis dtpgs 0=dis 1=en 2=ntusd 3=N/A
Elements| HEX| N/A
--------------------------------
1| 75| 117.0
2| d5| 213.0
3| 57| 87.0
4| 57| 87.0
5| 5f| 95.0
6| ff| 255.0
7| 3f| 63.0
8| ff| 255.0
9| ff| 255.0
10| ff| 255.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
dp_offset_threshold B74 0.0 "" 00 E B
dpofth allowable range of DPOFDF

NAME: dvb_high_amp ADDR: B75 UNT: "" OWN: V CODE: dvbhig


EQN: E*100
DVB current required for high braking as f(RPM)
RPM| HEX| ""
--------------------------------
150.0| 46| 0.700
300.0| 46| 0.700
450.0| 46| 0.700
600.0| 46| 0.700
750.0| 46| 0.700
900.0| 46| 0.700
1050.0| 46| 0.700
1200.0| 50| 0.800
1350.0| 50| 0.800
1500.0| 5a| 0.900
1650.0| 64| 1.000
1800.0| 6e| 1.100
1950.0| 78| 1.200
2100.0| 82| 1.300
2250.0| 69| 1.050
2400.0| 58| 0.880
2550.0| 50| 0.800
NAME: dvb_low_amp ADDR: B86 UNT: "" OWN: V CODE: dvblow
EQN: E*100
DVB current required for low braking as f(RPM)
RPM| HEX| ""
--------------------------------
150.0| 46| 0.700
300.0| 46| 0.700
450.0| 46| 0.700
600.0| 46| 0.700
750.0| 46| 0.700
900.0| 46| 0.700
1050.0| 46| 0.700
1200.0| 46| 0.700
1350.0| 46| 0.700
1500.0| 46| 0.700
1650.0| 46| 0.700
1800.0| 46| 0.700
1950.0| 46| 0.700
2100.0| 50| 0.800
2250.0| 50| 0.800
2400.0| 50| 0.800
2550.0| 50| 0.800

NAME: dvb_med_amp ADDR: B97 UNT: "" OWN: V CODE: dvbmed


EQN: E*100
DVB current required for med braking as f(RPM)
RPM| HEX| ""
--------------------------------
150.0| 46| 0.700
300.0| 46| 0.700
450.0| 46| 0.700
600.0| 46| 0.700
750.0| 46| 0.700
900.0| 46| 0.700
1050.0| 46| 0.700
1200.0| 41| 0.650
1350.0| 41| 0.650
1500.0| 41| 0.650
1650.0| 41| 0.650
1800.0| 41| 0.650
1950.0| 41| 0.650
2100.0| 46| 0.700
2250.0| 46| 0.700
2400.0| 46| 0.700
2550.0| 46| 0.700

NAME: exhaust_bp_limit ADDR: BA8 UNT: "" OWN: V CODE: ebplim


EQN: E*2.31985
press over which ebp scaledhilimit fault is logged
Tq*RPM| HEX| ""
--------------------------------
0.0| 27| 16.81
150.0| 27| 16.81
300.0| 27| 16.81
450.0| 27| 16.81
600.0| 27| 16.81
750.0| 27| 16.81
900.0| 27| 16.81
1050.0| 27| 16.81
1200.0| 27| 16.81
1350.0| 27| 16.81
1500.0| 27| 16.81
1650.0| 27| 16.81
1800.0| 27| 16.81
1950.0| 27| 16.81
2100.0| 27| 16.81
2250.0| 27| 16.81
2400.0| 27| 16.81

NAME: egr_air_temp_threshold ADDR: BB9 UNT: "" OWN: B CODE: egratt


EQN: (E+40)*0.9
base cal for intake air temp to disable EGR conden
Boost-kPa| HEX| ""
--------------------------------
0.0| 00| -40.0
15.0| 00| -40.0
30.0| 00| -40.0
45.0| 00| -40.0
60.0| 00| -40.0
75.0| 00| -40.0
90.0| 00| -40.0
105.0| 00| -40.0
120.0| 00| -40.0
135.0| 00| -40.0
150.0| 00| -40.0
165.0| 00| -40.0
180.0| 00| -40.0
195.0| 00| -40.0
210.0| 00| -40.0
225.0| 00| -40.0
240.0| 00| -40.0

NAME: egr_clt_temp_threshold ADDR: BCA UNT: "" OWN: B CODE: egrctt


EQN: (E+40)*0.9
base cal for eng cool temp to disable EGR condens
Boost-kPa| HEX| ""
--------------------------------
0.0| 00| -40.0
15.0| 00| -40.0
30.0| 00| -40.0
45.0| 00| -40.0
60.0| 00| -40.0
75.0| 00| -40.0
90.0| 00| -40.0
105.0| 00| -40.0
120.0| 00| -40.0
135.0| 00| -40.0
150.0| 00| -40.0
165.0| 00| -40.0
180.0| 00| -40.0
195.0| 00| -40.0
210.0| 00| -40.0
225.0| 00| -40.0
240.0| 00| -40.0

NAME: egr_desired_rate ADDR: BDB UNT: "" OWN: B CODE: egrdes


EQN: E*16
desired EGR flow rate for PID, f(eng speed, load)

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
X 300.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
I 450.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
S 600.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
_ 750.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
R 900.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
P 1050.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
M 1200.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
_ 1350.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
1 1500.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
7 1650.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
1800.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
1950.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
2100.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
2250.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
2400.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
2550.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 00 00 00 00 00
00 00 00
X 300.0 | 00 00 00 00 00 00
00 00 00
I 450.0 | 00 00 00 00 00 00
00 00 00
S 600.0 | 00 00 00 00 00 00
00 00 00
_ 750.0 | 00 00 00 00 00 00
00 00 00
R 900.0 | 00 00 00 00 00 00
00 00 00
P 1050.0 | 00 00 00 00 00 00
00 00 00
M 1200.0 | 00 00 00 00 00 00
00 00 00
_ 1350.0 | 00 00 00 00 00 00
00 00 00
1 1500.0 | 00 00 00 00 00 00
00 00 00
7 1650.0 | 00 00 00 00 00 00
00 00 00
1800.0 | 00 00 00 00 00 00
00 00 00
1950.0 | 00 00 00 00 00 00
00 00 00
2100.0 | 00 00 00 00 00 00
00 00 00
2250.0 | 00 00 00 00 00 00
00 00 00
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: egr_min_boost ADDR: C74 UNT: "" OWN: B CODE: egrmnb


EQN: E*1.15992
min allowable boost press when running EGR

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
X 300.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
I 450.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
S 600.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 750.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
R 900.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
P 1050.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
M 1200.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 1350.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1 1500.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
7 1650.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1800.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1950.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2100.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2250.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2400.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2550.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 00 00 00 00 00
00 00 00
X 300.0 | 00 00 00 00 00 00
00 00 00
I 450.0 | 00 00 00 00 00 00
00 00 00
S 600.0 | 00 00 00 00 00 00
00 00 00
_ 750.0 | 00 00 00 00 00 00
00 00 00
R 900.0 | 00 00 00 00 00 00
00 00 00
P 1050.0 | 00 00 00 00 00 00
00 00 00
M 1200.0 | 00 00 00 00 00 00
00 00 00
_ 1350.0 | 00 00 00 00 00 00
00 00 00
1 1500.0 | 00 00 00 00 00 00
00 00 00
7 1650.0 | 00 00 00 00 00 00
00 00 00
1800.0 | 00 00 00 00 00 00
00 00 00
1950.0 | 00 00 00 00 00 00
00 00 00
2100.0 | 00 00 00 00 00 00
00 00 00
2250.0 | 00 00 00 00 00 00
00 00 00
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00
NAME: egr_rate_to_vane_pos ADDR: D0D UNT: "" OWN: B CODE: egrper
EQN: E*128
flow rate vs VNT vanes pos, f(eng speed, load)

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
X 300.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
I 450.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
S 600.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
_ 750.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
R 900.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
P 1050.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
M 1200.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
_ 1350.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
1 1500.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
7 1650.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
1800.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
1950.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
2100.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
2250.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
2400.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
2550.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 00 00 00 00 00
00 00 00
X 300.0 | 00 00 00 00 00 00
00 00 00
I 450.0 | 00 00 00 00 00 00
00 00 00
S 600.0 | 00 00 00 00 00 00
00 00 00
_ 750.0 | 00 00 00 00 00 00
00 00 00
R 900.0 | 00 00 00 00 00 00
00 00 00
P 1050.0 | 00 00 00 00 00 00
00 00 00
M 1200.0 | 00 00 00 00 00 00
00 00 00
_ 1350.0 | 00 00 00 00 00 00
00 00 00
1 1500.0 | 00 00 00 00 00 00
00 00 00
7 1650.0 | 00 00 00 00 00 00
00 00 00
1800.0 | 00 00 00 00 00 00
00 00 00
1950.0 | 00 00 00 00 00 00
00 00 00
2100.0 | 00 00 00 00 00 00
00 00 00
2250.0 | 00 00 00 00 00 00
00 00 00
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: egr_sstate_output ADDR: DA6 UNT: "" OWN: B CODE: egrsso


EQN: E*2
ff ss %dc for VNT vanes pos during EGR ctrl

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
X 300.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
I 450.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
S 600.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 750.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
R 900.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
P 1050.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
M 1200.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 1350.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1 1500.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
7 1650.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1800.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1950.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2100.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2250.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2400.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2550.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 00 00 00 00 00
00 00 00
X 300.0 | 00 00 00 00 00 00
00 00 00
I 450.0 | 00 00 00 00 00 00
00 00 00
S 600.0 | 00 00 00 00 00 00
00 00 00
_ 750.0 | 00 00 00 00 00 00
00 00 00
R 900.0 | 00 00 00 00 00 00
00 00 00
P 1050.0 | 00 00 00 00 00 00
00 00 00
M 1200.0 | 00 00 00 00 00 00
00 00 00
_ 1350.0 | 00 00 00 00 00 00
00 00 00
1 1500.0 | 00 00 00 00 00 00
00 00 00
7 1650.0 | 00 00 00 00 00 00
00 00 00
1800.0 | 00 00 00 00 00 00
00 00 00
1950.0 | 00 00 00 00 00 00
00 00 00
2100.0 | 00 00 00 00 00 00
00 00 00
2250.0 | 00 00 00 00 00 00
00 00 00
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: ess_break_tq_dither_amp_factor ADDR: E3F UNT: "" OWN: V CODE:


essbta EQN: E*16
Ampltd of RPM dthr func as a func of ovrall gr rat
Ratio| HEX| ""
--------------------------------
0.0| 12| 1.13
5.0| 14| 1.25
10.0| 14| 1.25
15.0| 14| 1.25
20.0| 15| 1.31
25.0| 15| 1.31
30.0| 17| 1.44
35.0| 1a| 1.63
40.0| 1a| 1.63
45.0| 1a| 1.63
50.0| 1a| 1.63
55.0| 1a| 1.63
60.0| 1a| 1.63
65.0| 1a| 1.63
70.0| 1a| 1.63
75.0| 1a| 1.63
80.0| 1a| 1.63

NAME: ess_break_tq_dither_function ADDR: E50 UNT: "" OWN: V CODE:


essbtd EQN: E*64
Normalized func for one period to perf tq dither
Ratio| HEX| ""
--------------------------------
0.0| 40| 1.000
6.3| 3b| 0.922
12.5| 2d| 0.703
18.8| 18| 0.375
25.0| 00| 0.000
31.3| ffffffe8| -0.375
37.5| ffffffd3| -0.703
43.8| ffffffc5| -0.922
50.0| ffffffc0| -1.000
56.3| ffffffc5| -0.922
62.5| ffffffd3| -0.703
68.8| ffffffe8| -0.375
75.0| 00| 0.000
81.3| 18| 0.375
87.5| 2d| 0.703
93.8| 3b| 0.922
100.0| 40| 1.000

NAME: ess_break_tq_filter_tau ADDR: E61 UNT: "" OWN: V CODE: essbtt


EQN: E*256
Tau for filt tq trnstn as a func of overall gr rat
Ratio| HEX| ""
--------------------------------
0.0| 03| 0.0117
5.0| 0a| 0.0391
10.0| 12| 0.0703
15.0| 1a| 0.1016
20.0| 1f| 0.1211
25.0| 21| 0.1289
30.0| 24| 0.1406
35.0| 26| 0.1484
40.0| 26| 0.1484
45.0| 29| 0.1602
50.0| 29| 0.1602
55.0| 29| 0.1602
60.0| 2c| 0.1719
65.0| 2c| 0.1719
70.0| 2e| 0.1797
75.0| 2e| 0.1797
80.0| 2e| 0.1797

NAME: ess_break_tq_period ADDR: E72 UNT: "" OWN: V CODE: essbtp


EQN: E*40
Period of tq dthr as a func of overall gr ratio
Ratio| HEX| ""
--------------------------------
0.0| 09| 0.225
5.0| 0c| 0.300
10.0| 10| 0.400
15.0| 14| 0.500
20.0| 18| 0.600
25.0| 18| 0.600
30.0| 18| 0.600
35.0| 1e| 0.750
40.0| 1e| 0.750
45.0| 1e| 0.750
50.0| 1e| 0.750
55.0| 1e| 0.750
60.0| 1e| 0.750
65.0| 1e| 0.750
70.0| 1e| 0.750
75.0| 1e| 0.750
80.0| 1e| 0.750

NAME: ess_rpm_tq_dither_amp_factor ADDR: E83 UNT: "" OWN: V CODE:


essrta EQN: E*16
Amplitude of RPM/TQ dither-function of gear ratio
Ratio| HEX| ""
--------------------------------
0.0| 10| 1.00
5.0| 10| 1.00
10.0| 11| 1.06
15.0| 12| 1.13
20.0| 13| 1.19
25.0| 15| 1.31
30.0| 17| 1.44
35.0| 1a| 1.63
40.0| 1a| 1.63
45.0| 1a| 1.63
50.0| 1a| 1.63
55.0| 1a| 1.63
60.0| 1a| 1.63
65.0| 1a| 1.63
70.0| 1a| 1.63
75.0| 1a| 1.63
80.0| 1a| 1.63
NAME: ess_rpm_tq_dither_function ADDR: E94 UNT: "" OWN: V CODE: essrtd
EQN: E*64
Periodic function of time for one oscillation
Ratio| HEX| ""
--------------------------------
0.0| 00| 0.000
6.3| 20| 0.500
12.5| 2d| 0.703
18.8| 3a| 0.906
25.0| 40| 1.000
31.3| 3a| 0.906
37.5| 2d| 0.703
43.8| 20| 0.500
50.0| 00| 0.000
56.3| ffffffe0| -0.500
62.5| ffffffd3| -0.703
68.8| ffffffc6| -0.906
75.0| ffffffc0| -1.000
81.3| ffffffc6| -0.906
87.5| ffffffd3| -0.703
93.8| ffffffe0| -0.500
100.0| 00| 0.000

NAME: ess_rpm_tq_dither_period ADDR: EA5 UNT: "" OWN: V CODE: essrtp


EQN: E*40
Period of the tq dither as function of gear ratio
Ratio| HEX| ""
--------------------------------
0.0| 09| 0.225
5.0| 0c| 0.300
10.0| 10| 0.400
15.0| 14| 0.500
20.0| 18| 0.600
25.0| 18| 0.600
30.0| 18| 0.600
35.0| 1e| 0.750
40.0| 1e| 0.750
45.0| 1e| 0.750
50.0| 1e| 0.750
55.0| 1e| 0.750
60.0| 1e| 0.750
65.0| 1e| 0.750
70.0| 1e| 0.750
75.0| 1e| 0.750
80.0| 1e| 0.750

NAME: ess_torque_transition_rate ADDR: EB6 UNT: %tq/ OWN: V CODE: essttr


EQN: E/15.6863
Linear trnstion rate of mving currnt tq to tqlimit
Elements| HEX| %tq/Sec
--------------------------------
1| 05| 78.4
2| 0a| 156.9

NAME: fan_pwm_output ADDR: EB8 UNT: "" OWN: E CODE: fanpwm


EQN: E*2
fanPWM%DC: degC=MAX(Air,Clt,IC,Oil Temp - ?TFPWM)
dgC| HEX| ""
--------------------------------
0.0| 00| 0.0
1.1| 00| 0.0
2.2| 14| 10.0
3.3| 50| 40.0
4.4| a0| 80.0
5.6| c8| 100.0
6.7| c8| 100.0
7.8| c8| 100.0
8.9| c8| 100.0

NAME: friction_tq_loss_temp_factor ADDR: EC1 UNT: "" OWN: B CODE:


ftqltf EQN: E*50
friction_torque_loss temp based table multiplier
dgC| HEX| ""
--------------------------------
-40.0| 87| 2.700
-27.8| 87| 2.700
-15.6| 87| 2.700
-3.3| 87| 2.700
8.9| 83| 2.620
21.1| 5e| 1.880
33.3| 4f| 1.580
45.6| 45| 1.380
57.8| 3f| 1.260
70.0| 3b| 1.180
82.2| 37| 1.100
94.4| 34| 1.040
106.7| 32| 1.000
118.9| 32| 1.000
131.1| 32| 1.000
143.3| 32| 1.000
155.6| 32| 1.000

NAME: fuel_temp_offset_boi ADDR: ED2 UNT: "" OWN: B CODE: fulboi


EQN: E*4
delta BOI as a f(fuel temperature)
dgC| HEX| ""
--------------------------------
7.0| 00| 0.00
11.0| 00| 0.00
15.0| 00| 0.00
19.0| 00| 0.00
23.0| 00| 0.00
27.0| 00| 0.00
31.0| 00| 0.00
35.0| 00| 0.00
39.0| 00| 0.00
43.0| 00| 0.00
47.0| 00| 0.00
51.0| 00| 0.00
55.0| 00| 0.00
59.0| 00| 0.00
63.0| 00| 0.00
67.0| 00| 0.00
71.0| 00| 0.00

NAME: friction_torque_loss ADDR: EE3 UNT: "" OWN: B CODE: tqlost


EQN: E*2.55
engine's friction torque loss f(RPM)
RPM| HEX| ""
--------------------------------
150.0| 08| 3.14
300.0| 08| 3.14
450.0| 09| 3.53
600.0| 0a| 3.92
750.0| 0b| 4.31
900.0| 0c| 4.71
1050.0| 0d| 5.10
1200.0| 0f| 5.88
1350.0| 10| 6.27
1500.0| 12| 7.06
1650.0| 13| 7.45
1800.0| 15| 8.24
1950.0| 17| 9.02
2100.0| 18| 9.41
2250.0| 1a| 10.20
2400.0| 1b| 10.59
2550.0| 1c| 10.98

NAME: fuel_pressure_max ADDR: EF4 UNT: "" OWN: V CODE: fphigh


EQN: E/6.897
fuel press>fphigh as f(RPM) to log code
RPM| HEX| ""
--------------------------------
150.0| ff| 1758.7
300.0| ff| 1758.7
450.0| ff| 1758.7
600.0| ff| 1758.7
750.0| ff| 1758.7
900.0| ff| 1758.7
1050.0| ff| 1758.7
1200.0| ff| 1758.7
1350.0| ff| 1758.7
1500.0| ff| 1758.7
1650.0| ff| 1758.7
1800.0| ff| 1758.7
1950.0| ff| 1758.7
2100.0| ff| 1758.7
2250.0| ff| 1758.7
2400.0| ff| 1758.7
2550.0| ff| 1758.7

NAME: fuel_pressure_min ADDR: F05 UNT: "" OWN: B CODE: fplow


EQN: E/6.897
fuel press<fplow as f(RPM) to log code
RPM| HEX| ""
--------------------------------
150.0| 00| 0.0
300.0| 00| 0.0
450.0| 00| 0.0
600.0| 06| 41.4
750.0| 0b| 75.9
900.0| 11| 117.2
1050.0| 16| 151.7
1200.0| 1a| 179.3
1350.0| 1f| 213.8
1500.0| 24| 248.3
1650.0| 28| 275.9
1800.0| 2d| 310.4
1950.0| 2d| 310.4
2100.0| 2d| 310.4
2250.0| 2d| 310.4
2400.0| 2d| 310.4
2550.0| 2d| 310.4

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
grp_lockout_passwd F16 "0000" V
lockpw factory password for COMGRP DDR reprogramg lockout

NAME: injector_calibrations ADDR: F1A UNT: CODE OWN: D CODE: injcal


EQN: E
encoded fuel output compensation for each INJECTOR
Elements| HEX| CODE
--------------------------------
1| 34| 52.0
2| 3b| 59.0
3| 3c| 60.0
4| 2d| 45.0
5| 27| 39.0
6| 06| 6.0
7| 01| 1.0
8| 01| 1.0

NAME: injector_fudge_factors ADDR: F22 UNT: MLT OWN: V CODE: injfdg


EQN: E*128
a PW multiplier for each CYLINDER -NOT UNTIL R2.01
Elements| HEX| MLT
--------------------------------
1| 80| 1.000
2| 80| 1.000
3| 80| 1.000
4| 80| 1.000
5| 80| 1.000
6| 80| 1.000
7| 80| 1.000
8| 80| 1.000

NAME: injector_max_allowed ADDR: F2A UNT: "" OWN: V CODE: irtmax


EQN: E/32
risetime>IRTMAX(Vbat)+irtdly to log risetime long
Volts| HEX| ""
--------------------------------
0.0| ff| 8160.0
3.2| b9| 5920.0
6.4| 5e| 3008.0
9.6| 3b| 1888.0
12.8| 31| 1568.0
16.0| 2c| 1408.0
19.2| 2a| 1344.0
22.4| 28| 1280.0
25.6| 27| 1248.0
28.8| 26| 1216.0
32.0| 26| 1216.0
35.2| 25| 1184.0
38.4| 25| 1184.0
41.6| 24| 1152.0
44.8| 24| 1152.0
48.0| 24| 1152.0
51.2| 24| 1152.0

NAME: injector_min_allowed ADDR: F3B UNT: "" OWN: V CODE: irtmin


EQN: E/32
risetime<IRTMIN(Vbat)+irtdly to log risetime short
Volts| HEX| ""
--------------------------------
0.0| 80| 4096.0
3.2| 5f| 3040.0
6.4| 3b| 1888.0
9.6| 1f| 992.0
12.8| 18| 768.0
16.0| 15| 672.0
19.2| 14| 640.0
22.4| 12| 576.0
25.6| 11| 544.0
28.8| 10| 512.0
32.0| 0f| 480.0
35.2| 0f| 480.0
38.4| 0e| 448.0
41.6| 0e| 448.0
44.8| 0d| 416.0
48.0| 0d| 416.0
51.2| 0d| 416.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
injector_password F4C "0000" V
injpw Injector Password req'd to change Inj Cal Codes

NAME: j1939_engine_torque_modes ADDR: F50 UNT: MID OWN: V CODE: jhietm


EQN: E
J1939: device IDs allowed to command engine
Elements| HEX| MID
--------------------------------
1| 06| 6.0
2| 00| 0.0

NAME: j1939_retarder_torque_modes ADDR: F52 UNT: MID OWN: V CODE:


jhirtm EQN: E
J1939: device IDs allowed to command retarder
Elements| HEX| MID
--------------------------------
1| 06| 6.0
2| 00| 0.0

NAME: j1939_tsc1_sources ADDR: F54 UNT: ADR OWN: V CODE: jhitss


EQN: E
J1939: source addr for TSC1 eng/rtrdr msg devices
Elements| HEX| ADR
--------------------------------
1| 03| 3.0
2| ff| 255.0

NAME: jake_brake_cylinders ADDR: F56 UNT: MSK OWN: V CODE: jbcyls


EQN: E
Jake Brk: identifies cyls cntld in lo,md,hi modes
Elements| HEX| MSK
--------------------------------
1| 01| 1.0
2| 04| 4.0
3| 08| 8.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
manufacturer_id_code F59 "DTDSC" V
zmfrid Manufacturer Identification - 5 Bytes
model_number F5E "6067MK60" E
zmodn Engine Model Number - 8 Bytes

NAME: mm_oil_drain_time ADDR: F66 UNT: "" OWN: V CODE: mmodnt


EQN: E*4
Max. time after eng. has stopped to check OLS
dgC| HEX| ""
--------------------------------
-40.0| 3c| 15.00
-27.8| 3c| 15.00
-15.6| 3c| 15.00
-3.3| 28| 10.00
8.9| 14| 5.00
21.1| 10| 4.00
33.3| 10| 4.00
45.6| 10| 4.00
57.8| 10| 4.00
70.0| 10| 4.00
82.2| 10| 4.00
94.4| 10| 4.00
106.7| 10| 4.00
118.9| 10| 4.00
131.1| 10| 4.00
143.3| 10| 4.00
155.6| 10| 4.00

NAME: optimum_load_torque_curve ADDR: F77 UNT: "" OWN: V CODE: olcftq


EQN: E*2.55
Torque at which PWM=olcnom
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00
300.0| 00| 0.00
450.0| 00| 0.00
600.0| 13| 7.45
750.0| 1c| 10.98
900.0| 25| 14.51
1050.0| 30| 18.82
1200.0| 3d| 23.92
1350.0| 54| 32.94
1500.0| 83| 51.37
1650.0| a8| 65.88
1800.0| c2| 76.08
1950.0| d5| 83.53
2100.0| e3| 89.02
2250.0| e3| 89.02
2400.0| e3| 89.02
2550.0| e3| 89.02
NAME: optimum_load_norm_tq_delta ADDR: F88 UNT: "" OWN: V CODE: olcntd
EQN: E*2.55
normalizing torqe offset from olcftq
RPM| HEX| ""
--------------------------------
150.0| 2f| 18.43
300.0| 2f| 18.43
450.0| 2f| 18.43
600.0| 2f| 18.43
750.0| 31| 19.22
900.0| 33| 20.00
1050.0| 36| 21.18
1200.0| 70| 43.92
1350.0| ab| 67.06
1500.0| 7c| 48.63
1650.0| 57| 34.12
1800.0| 36| 21.18
1950.0| 19| 9.80
2100.0| 17| 9.02
2250.0| 16| 8.63
2400.0| 16| 8.63
2550.0| 16| 8.63

NAME: optimum_rpm ADDR: F99 UNT: "" OWN: V CODE: optrpm


EQN: E/16
RPM for optimal BSFC f(powertrain demand)
%_Load| HEX| ""
--------------------------------
0.0| 4b| 1200.0
12.5| 4b| 1200.0
25.0| 4b| 1200.0
37.5| 4b| 1200.0
50.0| 4e| 1248.0
62.5| 54| 1344.0
75.0| 5b| 1456.0
87.5| 5e| 1504.0
100.0| 84| 2112.0

NAME: optimum_rpm_asymadj ADDR: FA2 UNT: "" OWN: V CODE: drpmaa


EQN: E*255
RPM Asymmetry Adjustment for optimal BSFC f(PTDM)
%_Load| HEX| ""
--------------------------------
0.0| ff| 1.0000
12.5| ff| 1.0000
25.0| ff| 1.0000
37.5| ff| 1.0000
50.0| e0| 0.8784
62.5| a1| 0.6314
75.0| 80| 0.5020
87.5| 61| 0.3804
100.0| 00| 0.0000

NAME: park_brake_offset_boi ADDR: FAB UNT: "" OWN: V CODE: pboboi


EQN: E*4
BOI comp add whn pb is set as func of wghted temp
dgC| HEX| ""
--------------------------------
-40.0| 20| 8.00
-27.8| 1c| 7.00
-15.6| 1a| 6.50
-3.3| 18| 6.00
8.9| 18| 6.00
21.1| 18| 6.00
33.3| 18| 6.00
45.6| 18| 6.00
57.8| 18| 6.00
70.0| 18| 6.00
82.2| 18| 6.00
94.4| 18| 6.00
106.7| 18| 6.00
118.9| 00| 0.00
131.1| 00| 0.00
143.3| 00| 0.00
155.6| 00| 0.00

NAME: pid_enable_map ADDR: FBC UNT: Flg OWN: S CODE: pidmap


EQN: E
J1587 Periodic Output Map-1 bit for PIDs 0 to 255
Elements| HEX| Flg
--------------------------------
1| 01| 1.0
2| 20| 32.0
3| 00| 0.0
4| 00| 0.0
5| 00| 0.0
6| 10| 16.0
7| 01| 1.0
8| 00| 0.0
9| d2| 210.0
10| 04| 4.0
11| f8| 248.0
12| 3b| 59.0
13| 50| 80.0
14| d4| 212.0
15| 02| 2.0
16| 06| 6.0
17| 00| 0.0
18| 00| 0.0
19| 00| 0.0
20| 0c| 12.0
21| 40| 64.0
22| d9| 217.0
23| c0| 192.0
24| 7b| 123.0
25| 15| 21.0
26| 00| 0.0
27| 00| 0.0
28| 00| 0.0
29| 10| 16.0
30| 3e| 62.0
31| b9| 185.0
32| 1f| 31.0
33| 00| 0.0
34| 00| 0.0
35| 00| 0.0
36| 00| 0.0
37| 00| 0.0
38| 00| 0.0
39| 00| 0.0
40| 00| 0.0
41| 00| 0.0
42| 00| 0.0
43| 00| 0.0
44| 00| 0.0
45| 00| 0.0
46| 00| 0.0
47| 00| 0.0
48| 00| 0.0
49| 00| 0.0
50| 00| 0.0
51| 00| 0.0
52| 00| 0.0
53| 00| 0.0
54| 00| 0.0
55| 00| 0.0
56| 00| 0.0
57| 00| 0.0
58| 00| 0.0
59| 00| 0.0
60| 00| 0.0
61| 00| 0.0
62| 00| 0.0
63| 00| 0.0
64| 00| 0.0

NAME: pin_to_sid ADDR: FFC UNT: "" OWN: E CODE: pinsid


EQN: E
maps 16 external analog phys channels to SID value
pid_pin| HEX| ""
--------------------------------
0.0| 00| 0.0
1.0| 00| 0.0
2.0| 00| 0.0
3.0| 00| 0.0
4.0| 00| 0.0
5.0| 00| 0.0
6.0| 00| 0.0
7.0| 00| 0.0
8.0| 00| 0.0
9.0| 00| 0.0
10.0| 00| 0.0
11.0| 00| 0.0
12.0| 00| 0.0
13.0| 00| 0.0
14.0| 00| 0.0
15.0| 00| 0.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
rating_password 100C "0000" V
ratpw Rating Password req'd to change rating selection
serial_number 1010 "06R0616721" E
zmfrsn Engine Serial Number - 10 Bytes

NAME: shutdn_cool_pressure ADDR: 101A UNT: "" OWN: B CODE: discop


EQN: E/1.72425
coolant press < discop f(RPM) to log low clnt pres
RPM| HEX| ""
--------------------------------
150.0| 00| 0.0
300.0| 00| 0.0
450.0| 00| 0.0
600.0| 00| 0.0
750.0| 00| 0.0
900.0| 00| 0.0
1050.0| 00| 0.0
1200.0| 00| 0.0
1350.0| 00| 0.0
1500.0| 00| 0.0
1650.0| 00| 0.0
1800.0| 00| 0.0
1950.0| 00| 0.0
2100.0| 00| 0.0
2250.0| 00| 0.0
2400.0| 00| 0.0
2550.0| 00| 0.0

NAME: shutdn_oil_pressure ADDR: 102B UNT: "" OWN: V CODE: disolp


EQN: E/6.897
oil press<disolp as f(RPM) to log low oil pressure
RPM| HEX| ""
--------------------------------
150.0| 00| 0.0
300.0| 00| 0.0
450.0| 04| 27.6
600.0| 06| 41.4
750.0| 09| 62.1
900.0| 0d| 89.7
1050.0| 11| 117.2
1200.0| 14| 137.9
1350.0| 17| 158.6
1500.0| 1a| 179.3
1650.0| 1b| 186.2
1800.0| 1c| 193.1
1950.0| 1d| 200.0
2100.0| 1e| 206.9
2250.0| 1e| 206.9
2400.0| 1e| 206.9
2550.0| 1e| 206.9

NAME: shutdn_rpm_ratio ADDR: 103C UNT: "" OWN: E CODE: stpsst


EQN: E*256
stop engine RPM derate Table f(time) for PTO
Secs| HEX| ""
--------------------------------
0.0| ff| 0.9961
4.0| f0| 0.9375
8.0| e0| 0.8750
12.0| d1| 0.8164
16.0| c2| 0.7578
20.0| b2| 0.6953
24.0| a3| 0.6367
28.0| 93| 0.5742
32.0| 84| 0.5156
36.0| 75| 0.4570
40.0| 65| 0.3945
44.0| 56| 0.3359
48.0| 47| 0.2773
52.0| 37| 0.2148
56.0| 28| 0.1563
60.0| 19| 0.0977
64.0| 09| 0.0352

NAME: shutdn_torque_ratio ADDR: 104D UNT: "" OWN: E CODE: stptst


EQN: E*256
stop engine TORQUE derate Table f(time)
Secs| HEX| ""
--------------------------------
0.0| ff| 0.9961
4.0| f7| 0.9648
8.0| f0| 0.9375
12.0| e8| 0.9063
16.0| e0| 0.8750
20.0| d9| 0.8477
24.0| d1| 0.8164
28.0| c9| 0.7852
32.0| c2| 0.7578
36.0| ba| 0.7266
40.0| b2| 0.6953
44.0| aa| 0.6641
48.0| a3| 0.6367
52.0| 9b| 0.6055
56.0| 93| 0.5742
60.0| 8c| 0.5469
64.0| 84| 0.5156

NAME: single_turbo_max_ltq ADDR: 105E UNT: "" OWN: B CODE: stmxtq


EQN: E*2.55
max tq before switching from single to dual turbo
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00
300.0| 00| 0.00
450.0| 00| 0.00
600.0| 00| 0.00
750.0| 00| 0.00
900.0| 00| 0.00
1050.0| 00| 0.00
1200.0| 00| 0.00
1350.0| 00| 0.00
1500.0| 00| 0.00
1650.0| 00| 0.00
1800.0| 00| 0.00
1950.0| 00| 0.00
2100.0| 00| 0.00
2250.0| 00| 0.00
2400.0| 00| 0.00
2550.0| 00| 0.00

NAME: single_turbo_min_ltq ADDR: 106F UNT: "" OWN: B CODE: stmntq


EQN: E*2.55
Min tq before switching from single to dual turbo
RPM| HEX| ""
--------------------------------
150.0| 4d| 30.20
300.0| 4d| 30.20
450.0| 4d| 30.20
600.0| 4d| 30.20
750.0| 4d| 30.20
900.0| 4d| 30.20
1050.0| 4d| 30.20
1200.0| 4d| 30.20
1350.0| 4d| 30.20
1500.0| 4d| 30.20
1650.0| 4d| 30.20
1800.0| 4d| 30.20
1950.0| 4d| 30.20
2100.0| 4d| 30.20
2250.0| 4d| 30.20
2400.0| 4d| 30.20
2550.0| 4d| 30.20

NAME: single_turbo_offset_boi ADDR: 1080 UNT: "" OWN: V CODE: sttboi


EQN: E*4
boi offset used for seq turbo when in single mode
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00
300.0| 00| 0.00
450.0| 00| 0.00
600.0| 00| 0.00
750.0| 00| 0.00
900.0| 00| 0.00
1050.0| 00| 0.00
1200.0| 00| 0.00
1350.0| 00| 0.00
1500.0| 00| 0.00
1650.0| 00| 0.00
1800.0| 00| 0.00
1950.0| 00| 0.00
2100.0| 00| 0.00
2250.0| 00| 0.00
2400.0| 00| 0.00
2550.0| 00| 0.00

NAME: single_turbo_torque_mult ADDR: 1091 UNT: "" OWN: V CODE: sttrqm


EQN: (E-0.5)*256
multiply with comp fin tq when seq turbo in single
RPM| HEX| ""
--------------------------------
150.0| 80| 1.0000
300.0| 80| 1.0000
450.0| 80| 1.0000
600.0| 80| 1.0000
750.0| 80| 1.0000
900.0| 80| 1.0000
1050.0| 80| 1.0000
1200.0| 80| 1.0000
1350.0| 80| 1.0000
1500.0| 80| 1.0000
1650.0| 80| 1.0000
1800.0| 80| 1.0000
1950.0| 80| 1.0000
2100.0| 80| 1.0000
2250.0| 80| 1.0000
2400.0| 80| 1.0000
2550.0| 80| 1.0000

NAME: slowdn_rpm_ratio ADDR: 10A2 UNT: "" OWN: E CODE: diwsst


EQN: E*256
eng overtemp protect RPM derate Table f(temp) PTO
dgC| HEX| ""
--------------------------------
0.0| ff| 0.9961
1.1| f1| 0.9414
2.2| e1| 0.8789
3.3| d2| 0.8203
4.4| c3| 0.7617
5.6| b3| 0.6992
6.7| a4| 0.6406
7.8| 94| 0.5781
8.9| 85| 0.5195
10.0| 85| 0.5195
11.1| 85| 0.5195
12.2| 85| 0.5195
13.3| 85| 0.5195
14.4| 85| 0.5195
15.6| 85| 0.5195
16.7| 85| 0.5195
17.8| 85| 0.5195

NAME: slowdn_torque_ratio ADDR: 10B3 UNT: "" OWN: E CODE: diwtst


EQN: E*256
eng overtemp protect TRQ derate Table f(temp)
dgC| HEX| ""
--------------------------------
0.0| ff| 0.9961
1.1| f1| 0.9414
2.2| e1| 0.8789
3.3| d2| 0.8203
4.4| c3| 0.7617
5.6| b3| 0.6992
6.7| a4| 0.6406
7.8| 94| 0.5781
8.9| 85| 0.5195
10.0| 85| 0.5195
11.1| 85| 0.5195
12.2| 85| 0.5195
13.3| 85| 0.5195
14.4| 85| 0.5195
15.6| 85| 0.5195
16.7| 85| 0.5195
17.8| 85| 0.5195

NAME: start_extra_torque ADDR: 10C4 UNT: "" OWN: B CODE: smdtq


EQN: E*2.55
cold start delta TORQUE Table f(RPM,oiltemp)

Table of AXIS_dgC_17_1
dgC ->
-40.0 -27.8 -15.6 -3.3 8.9 21.1
33.3 45.6 57.8 70.0 82.2 94.4 106.7 118.9
131.1 143.3 155.6
-----------------------------------------------------------------------------------
-----------------------------------------------------------------------------------
---------------------------------------
A 150.0 | 66.67 63.53 60.00 55.29 49.41 41.57
36.86 32.94 32.94 32.94 32.94 32.94 32.94 32.94
32.94 32.94 32.94
X 300.0 | 67.06 63.92 60.39 55.69 49.80 42.35
37.65 33.73 33.73 33.73 33.73 33.73 33.73 33.73
33.73 33.73 33.73
I 450.0 | 67.45 64.31 60.78 55.69 50.20 42.75
38.04 34.12 34.12 34.12 34.12 34.12 34.12 34.12
34.12 34.12 34.12
S 600.0 | 67.84 64.71 61.18 56.08 50.59 43.14
38.43 34.51 34.51 34.51 34.51 34.51 34.51 34.51
34.51 34.51 34.51
_ 750.0 | 68.24 65.10 61.57 56.47 50.98 43.53
38.82 34.90 34.90 34.90 34.90 34.90 34.90 34.90
34.90 34.90 34.90
R 900.0 | 68.63 65.49 61.96 56.86 51.37 43.92
39.22 35.29 35.29 35.29 35.29 35.29 35.29 35.29
35.29 35.29 35.29
P 1050.0 | 68.63 65.88 61.96 57.25 51.37 43.92
39.22 35.29 35.29 35.29 35.29 35.29 35.29 35.29
35.29 35.29 35.29
M 1200.0 | 72.55 69.80 65.49 60.78 54.51 46.67
39.61 35.69 35.69 35.69 35.69 35.69 35.69 35.69
35.69 35.69 35.69
_ 1350.0 | 72.94 70.20 65.88 61.18 54.90 47.06
40.00 36.08 36.08 36.08 36.08 36.08 36.08 36.08
36.08 36.08 36.08
1 1500.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
7 1650.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
1800.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
1950.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
2100.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
2250.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
2400.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
2550.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
Table of Hex Values
dgC ->
-40.0 -27.8 -15.6 -3.3 8.9 21.1
33.3 45.6 57.8 70.0 82.2 94.4 106.7 118.9
131.1 143.3 155.6
-----------------------------------------------------------------------------------
-----------------------------------------------------------------------------------
---------------------------------------
A 150.0 | aa a2 99 8d 7e 6a
5e 54 54 54 54 54 54 54
54 54 54
X 300.0 | ab a3 9a 8e 7f 6c
60 56 56 56 56 56 56 56
56 56 56
I 450.0 | ac a4 9b 8e 80 6d
61 57 57 57 57 57 57 57
57 57 57
S 600.0 | ad a5 9c 8f 81 6e
62 58 58 58 58 58 58 58
58 58 58
_ 750.0 | ae a6 9d 90 82 6f
63 59 59 59 59 59 59 59
59 59 59
R 900.0 | af a7 9e 91 83 70
64 5a 5a 5a 5a 5a 5a 5a
5a 5a 5a
P 1050.0 | af a8 9e 92 83 70
64 5a 5a 5a 5a 5a 5a 5a
5a 5a 5a
M 1200.0 | b9 b2 a7 9b 8b 77
65 5b 5b 5b 5b 5b 5b 5b
5b 5b 5b
_ 1350.0 | ba b3 a8 9c 8c 78
66 5c 5c 5c 5c 5c 5c 5c
5c 5c 5c
1 1500.0 | 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00
7 1650.0 | 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00
1800.0 | 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00
1950.0 | 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00
2100.0 | 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00
2250.0 | 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00
2400.0 | 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00
NAME: start_mode_boi ADDR: 11E5 UNT: "" OWN: B CODE: stboi
EQN: E*8
start mode BOI Table f(RPM)
RPM| HEX| ""
--------------------------------
150.0| 58| 11.00
300.0| 61| 12.13
450.0| 6b| 13.38
600.0| 7a| 15.25
750.0| 8c| 17.50
900.0| a0| 20.00
1050.0| a0| 20.00
1200.0| a0| 20.00
1350.0| a0| 20.00
1500.0| a0| 20.00
1650.0| a0| 20.00
1800.0| a0| 20.00
1950.0| a0| 20.00
2100.0| a0| 20.00
2250.0| a0| 20.00
2400.0| a0| 20.00
2550.0| a0| 20.00

NAME: steady_vnt_boost ADDR: 11F6 UNT: "" OWN: B CODE: svntbs


EQN: E/1.72425
desired turbo boost press for ss BOI operation

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
X 300.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
I 450.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
S 600.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 750.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
R 900.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
P 1050.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
M 1200.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 1350.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1 1500.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
7 1650.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1800.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1950.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2100.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2250.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2400.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2550.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 00 00 00 00 00
00 00 00
X 300.0 | 00 00 00 00 00 00
00 00 00
I 450.0 | 00 00 00 00 00 00
00 00 00
S 600.0 | 00 00 00 00 00 00
00 00 00
_ 750.0 | 00 00 00 00 00 00
00 00 00
R 900.0 | 00 00 00 00 00 00
00 00 00
P 1050.0 | 00 00 00 00 00 00
00 00 00
M 1200.0 | 00 00 00 00 00 00
00 00 00
_ 1350.0 | 00 00 00 00 00 00
00 00 00
1 1500.0 | 00 00 00 00 00 00
00 00 00
7 1650.0 | 00 00 00 00 00 00
00 00 00
1800.0 | 00 00 00 00 00 00
00 00 00
1950.0 | 00 00 00 00 00 00
00 00 00
2100.0 | 00 00 00 00 00 00
00 00 00
2250.0 | 00 00 00 00 00 00
00 00 00
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: t2_engage_time ADDR: 128F UNT: SEC OWN: V CODE: astent


EQN: E*40
Time required to confirm splitter engagement
Elements| HEX| SEC
--------------------------------
1| 06| 0.150
2| 06| 0.150
3| 06| 0.150
4| 06| 0.150

NAME: t2_gr_error ADDR: 1293 UNT: % OWN: V CODE: astgre


EQN: E*10.24
% tolerance of valide gear ratio error for in-gear
Elements| HEX| %
--------------------------------
1| 0a| 0.98
2| 0a| 0.98
3| 0a| 0.98
4| 0a| 0.98

NAME: t2_max_engage_time ADDR: 1297 UNT: SEC OWN: V CODE: astmet


EQN: E*40
Time to confirm after intial engagemnt is detected
Elements| HEX| SEC
--------------------------------
1| 14| 0.500
2| 14| 0.500
3| 14| 0.500
4| 14| 0.500

NAME: t2_neg_disengage_gr_error ADDR: 129B UNT: %GR OWN: V CODE: astnge


EQN: E*10.24
(-)%GearRatio error for out of gear confirmation
Elements| HEX| %GR
--------------------------------
1| 0a| 0.98
2| 0a| 0.98
3| 0a| 0.98
4| 0a| 0.98

NAME: t2_pos_disengage_gr_error ADDR: 129F UNT: %GR OWN: V CODE: astpge


EQN: E*10.24
(+)%GearRatio error for out of gear confirmation
Elements| HEX| %GR
--------------------------------
1| 0f| 1.46
2| 0f| 1.46
3| 0f| 1.46
4| 0f| 1.46

NAME: t2_ramp_timings ADDR: 12A3 UNT: --- OWN: V CODE: astrtm


EQN: E
inexplicable - will go away in future
Elements| HEX| ---
--------------------------------
1| 14| 20.0
2| 1a| 26.0
3| 2c| 44.0
4| 36| 54.0
5| 44| 68.0
6| 50| 80.0
7| 5c| 92.0
8| 68| 104.0

NAME: t2_retry_time ADDR: 12AB UNT: SEC OWN: V CODE: astryt


EQN: E*40
Splitter recycle time for commanding opp split st
Elements| HEX| SEC
--------------------------------
1| 0c| 0.300
2| 0c| 0.300
3| 0c| 0.300
4| 0c| 0.300

NAME: t2_rtd_kickdown ADDR: 12AF UNT: % Th OWN: V CODE: astrkd


EQN: E*2.55
percent throttle for kick downshifts
Elements| HEX|% Throttle
--------------------------------
1| e5| 89.80
2| e5| 89.80
3| e5| 89.80
4| e5| 89.80

NAME: t2_split_attempts ADDR: 12B3 UNT: # OWN: V CODE: astspa


EQN: E
Number of failed splitter shft attempts b4 fault
Elements| HEX| #
--------------------------------
1| 03| 3.0
2| 03| 3.0
3| 03| 3.0
4| 03| 3.0

NAME: t2_sync_diseng_time ADDR: 12B7 UNT: SEC OWN: V CODE: astsdt


EQN: E*40
Time required to confirm splitter dis-engagement
Elements| HEX| SEC
--------------------------------
1| 06| 0.150
2| 06| 0.150
3| 06| 0.150
4| 06| 0.150

NAME: t2_sync_dither_time ADDR: 12BB UNT: SEC OWN: V CODE: astsyt


EQN: E*40
Dither period for cycling around sync engage RPM
Elements| HEX| SEC
--------------------------------
1| 14| 0.500
2| 14| 0.500
3| 14| 0.500
4| 14| 0.500

NAME: torque_temp_correction ADDR: 12BF UNT: "" OWN: V CODE: fttqc


EQN: E*128
fuel temp TORQUE Compensation Table f(fuel temp)
dgC| HEX| ""
--------------------------------
-40.0| 7e| 0.984
-27.8| 7e| 0.984
-15.6| 7e| 0.984
-3.3| 7e| 0.984
8.9| 7e| 0.984
21.1| 7f| 0.992
33.3| 80| 1.000
45.6| 82| 1.016
57.8| 83| 1.023
70.0| 80| 1.000
82.2| 80| 1.000
94.4| 80| 1.000
106.7| 80| 1.000
118.9| 80| 1.000
131.1| 80| 1.000
143.3| 80| 1.000
155.6| 80| 1.000

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
vehicle_identification_number 12D0 "2HSCEAMR22C023330" D
vviinn VEHICLE IDENTIFICATION NUMBER: 17 ASCII characters

NAME: vnt_press_to_vane_pos ADDR: 12E1 UNT: "" OWN: B CODE: vntktv


EQN: E*24.6484
press vs VNT vanes pos, f(eng speed, load)

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
X 300.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
I 450.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
S 600.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
_ 750.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
R 900.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
P 1050.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
M 1200.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
_ 1350.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
1 1500.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
7 1650.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
1800.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
1950.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
2100.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
2250.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
2400.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000
2550.0 | 0.000 0.000 0.000 0.000 0.000 0.000
0.000 0.000 0.000

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 00 00 00 00 00
00 00 00
X 300.0 | 00 00 00 00 00 00
00 00 00
I 450.0 | 00 00 00 00 00 00
00 00 00
S 600.0 | 00 00 00 00 00 00
00 00 00
_ 750.0 | 00 00 00 00 00 00
00 00 00
R 900.0 | 00 00 00 00 00 00
00 00 00
P 1050.0 | 00 00 00 00 00 00
00 00 00
M 1200.0 | 00 00 00 00 00 00
00 00 00
_ 1350.0 | 00 00 00 00 00 00
00 00 00
1 1500.0 | 00 00 00 00 00 00
00 00 00
7 1650.0 | 00 00 00 00 00 00
00 00 00
1800.0 | 00 00 00 00 00 00
00 00 00
1950.0 | 00 00 00 00 00 00
00 00 00
2100.0 | 00 00 00 00 00 00
00 00 00
2250.0 | 00 00 00 00 00 00
00 00 00
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: vnt_turbo_spd_lmt_offset ADDR: 137A UNT: "" OWN: B CODE: vntslo


EQN: E/512
engine rpm based additive offset to the VNTTSL
RPM| HEX| ""
--------------------------------
150.0| 00| 0.0
300.0| 00| 0.0
450.0| 00| 0.0
600.0| 00| 0.0
750.0| 00| 0.0
900.0| 00| 0.0
1050.0| 00| 0.0
1200.0| 00| 0.0
1350.0| 00| 0.0
1500.0| 00| 0.0
1650.0| 00| 0.0
1800.0| 00| 0.0
1950.0| 00| 0.0
2100.0| 00| 0.0
2250.0| 00| 0.0
2400.0| 00| 0.0
2550.0| 00| 0.0

NAME: vnt_turbo_speed_limit ADDR: 138B UNT: "" OWN: B CODE: vnttsl


EQN: E/512
turbo speed lims based on baro press in PID alg
Boost-kPa| HEX| ""
--------------------------------
69.0| f9| 127488.0
73.3| f9| 127488.0
77.6| f9| 127488.0
81.9| f9| 127488.0
86.2| f9| 127488.0
90.5| f9| 127488.0
94.8| f9| 127488.0
99.1| f9| 127488.0
103.5| f9| 127488.0
107.8| f9| 127488.0
112.1| f9| 127488.0
116.4| f9| 127488.0
120.7| f9| 127488.0
125.0| f9| 127488.0
129.3| f9| 127488.0
133.6| f9| 127488.0
137.9| f9| 127488.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
absolute_max_boi 139C 32.00 DEG 80 E*4 V
absboi Max BOI after applying all compensations
ac_timer 139D 180.0 SEC b4 E O
actim Seconds FanCntrl#1 on after Air Cond turns off
acc_hrtbeat_timer 139E 15.0 Seco 0f E V
acctim Time to wait before 1st hearbeat msg from ACC devc
acceleration_filterconst 139F 0.500 % @ 40 E*128 V
veacfc MPH/sec fltrconst: new=old+veacfc*(new-old) @25msc
air_comp_load_delta 13A0 137.9 KPA a0 E*1.15992 D
pgsld AirComp kpa over set point to disable d_out f(#21)
air_comp_pressure_increment 13A1 5.08 %FS 0d E*2.56 O
pgspi Air Comp press incr in % of fuel scale press range
air_comp_unload_delta 13A2 172.4 KPA c8 E*1.15992 D
pgsud AirComp kpa over set point to enable d_out f(#21)
air_tq_reduction_max_tq 13A3 81.18 %TQ cf E*2.55 B
atqmax max/min allowed TQ w/ AIR TMP TQ LIMITING active..
air_tq_reduction_min_tq 13A4 60.00 %TQ 99 E*2.55 B
atqmin ..allowTQ decr as AirTmp/RPM incr to ATXTMP/ATXRPM
analog_conversion_fail_limit 13A5 8.0 DEC 08 E V
ancvfc # A/D conversion fails to log diagnostic
anti_theft_awake_time 13A6 10.0 min 0a E V
atftat time after ign off ECM stay awake for AntiThft msg
ati_filterconst 13A7 0.102 % @ 0d E*128 V
atifc Aux Timed Input filter constant
ati_function 13A8 0 = input unassigned, ignore it0 = input
unassigned, ignore it E atidst ATI function: 0=None 1=TurboSpd 2=Knock 3=VSG
ati_pulses_per_rev 13A9 12.0 PPR 0c E V
atippr Aux Timed Input pulses per revolution
ati_timeout 13AA 0.5 SEC 05 E*10 V
atitmo seconds to log missing Aux Timed Input pulses
auto_resume_timeout 13AB 3.000 SEC 78 E*40 V
ccatim max SECs Cruise Cnt suspended while shifting gears
baro_filterconst 13AC 0.063 %@1S 08 E*128 V
bpofc BARO & AmbientTmp filter cons @ 1sec if no sensors
baro_max_torque 13AD 20.00 % 33 E*2.55 V
bpmxtq FTRQ<bpmxtq*ztqscl to update BARO from TBS & AmbTp
baro_nox_1min_limit 13AE 0.4000 unit 66 E*255 V
bn1mnl 1min rol avg load above which BARBOI may + bnaadj
baro_nox_adapt_adjust 13AF -4.00 degr fffffff0 E*4 V
bnaadj the amount BARBOI is adj when load and baro thresh
baro_nox_temp_weighting 13B0 0.0000 "" 00 E*255 V
bxtwgf temp weighting factor for baro advanced strategy
baro_wait_time 13B1 1.0 SEC 0a E*10 V
bpuptm secs RPM<bpmxrp & FTRQ<bpmxtq to updte BARO &AmbTp
boi_temp_weighting 13B2 0.000 WGT 00 E*128 V
twfact CBOIAD temp weighting: temp=F*BOIPD1+(1-F)*BOIPD0
boost_max_torque 13B3 30.20 % 4d E*2.55 V
tbwtq FTRQ<tbwtq*ztqscl to log TBS failed high
boost_max_vane_pwm 13B4 100.0 % c8 E*2 B
bstmxv max dc for VNT vanes actuator when ctrl intake bst
boost_min_vane_pwm 13B5 0.0 % 00 E*2 B
bstmnv min dc for VNT vanes actuator when ctrl intake bst
broadcast_exh_temp_to_mid 13B6 0.0 unit 00 E B
bcexmd if !0 transmit exh temps continuously; else as req
bulb_check_time 13B7 5.0 SEC 05 E V
bcktim Ignition ON Bulb Check Time in seconds
cavitation_pressure 13B8 40.0 PSI 14 E/2 V
ftprps firetrk press gov: press<ftprps for cavitatation
cavitation_reset_pressure 13B9 0.0 PSI 00 E/2 V
ftpset firetrk press gov: press set point when cavitating
cavitation_timeout 13BA 5.0 SEC 05 E O
ftprt secs of cavitation before resetting press set pt
cc_ftmode_int_gain 13BB 10.00 R/(P 40 E*6.4 O
ftpig firetruck Press Gov integral gain: RPM/(PSI*SEC)
cc_ftmode_pressure_increment 13BC 4.0 P/S 04 E O
ftppi firetrk press gov: cc switch PSI incr/decrement
cc_ftmode_rpm_increment 13BD 25.0 R/S 19 E O
ftprpi firetrk RPM mode: cc switch RPM incr/decrement
cc_max_set_mph 13BE 60.0 MPH 78 E*2 D
ccmaxs CC: maximum allowable Cruise Control speed in MPH
cc_mph_increment 13BF 1.00 MPH 10 E*16 V
ccincm VSS CC: accel/cst MPH inc/dec & MPH/sec accel ramp
cc_mph_minimum 13C0 20.0 MPH 28 E*2 D
ccmins CC: minimum allowable Cruise Control speed in MPH
cc_rpm_increment 13C1 25.0 RPM 19 E D
ccincr CC: res/acl increment and set/cst decrement in RPM
cc_rpm_ramprate 13C2 200.0 R/S c8 E V
ccrrpm RPM cruise cntrl: resume ramp rate in RPM/secs
cc_set_point_timer 13C3 10.0 SEC 0a E V
ccsptr secs that VSS CC set pt retained w/ master sw off
clock_ratio_delta 13C4 0.9961 RATI ff E*256 V
clkdlt Clk/Cal spd error if ratio to TPU out 1 +/- clkdlt
cls2_out_of_cool_slosh 13C5 25.0 Minu 19 E V
c2ocst CLS2 sensor out of coolant slosh timer
cls2_in_cool_slosh 13C6 30.0 Seco 1e E V
c2icst CLS2 sensor in coolant slosh timer
comms_engine_type 13C7 2.0 Flg 02 E V
zengtp comms Engine Type ID: see 62T35, Tbl8, ID 214
comms_rpm_filter_constant 13C8 1.000 pure 80 E*128 V
cmrpmf Filter const. appld to J1587 PID190 (eng. spd)
certification_type 13C9 13.0 DEC 0d E V
certtp Not used-for future validatn engine type expansion
cold_engine_coolant_temp 13CA 70.0 dgC c6 (E+40)*1.8 V
cecoot Min eng coolant temp for cold eng signl activation
cold_engine_intercooler_temp 13CB 25.0 dgC 75 (E+40)*1.8 V
ceicot Min intercooler temp for cold eng signl activation
cold_engine_air_temp 13CC -1.1 dgC 46 (E+40)*1.8 V
ceairt Min eng air temp for cold eng signl activation
cold_engine_oil_temp 13CD -40.0 dgC 00 (E+40)*1.8 V
ceoilt Min eng oil temp for cold eng signl activation
cold_engine_temp_hyst 13CE 2.2 dgC 04 E*1.8 V
cehyst Hyst for all cold eng signl temperature thresholds
comp_bleed_max_cbv_dp_hyst 13CF 0.0 kPa 00 E/1.72425 B
cbvdph hyst used in transition from hi to low diff press
comp_bleed_rpm_reopen_delay 13D0 0.500 sec 14 E*40 B
cbvrod delay time to open turbo cbv if eng speed fluctats
coolant_level_limit_gain 13D1 0.1191 %/F 3d E*512 V
cllmgn CLS %lolvl GAIN: %lolvl=scldlolim+CLLMGN*radtemp
cylinders_in_engine 13D2 6.0 DEC 06 E V
zncylw Number of Cylinders in Engine
cylinders_this_box 13D3 6.0 DEC 06 E V
zncylh Number of Cylinders controlled by this ECM
d_in_e1_function 13D4 6 = throttle idle switch6 = throttle idle
switch O de1dst 08/#451,D2=Diag Req | 0=none,1=EB low,2=EB med,
d_in_f1_function 13D5 29 = A/C disengaged29 = A/C disengaged O
df1dst 02/#542,D2=SC off | 3=SD#1,4=SD#2,5=park brk,
d_in_f2_function 13D6 23 = cruise master23 = cruise master O
df2dst 04/#544,D2=RA off | 6=IVS,7=n/a,8=FT mode sw,
d_in_g1_function 13D7 25 = stop engine override25 = stop engine
override O dg1dst 07/#528,D2=STEO | 9=Th Inhib,10=RPM sync,
d_in_g2_function 13D8 17 = service brake released17 = service brake
released O dg2dst 06/#543,D2=BC off | 11=RPM frz,12=Rat1,13=Rat2,
d_in_g3_function 13D9 22 = resume/accel22 = resume/accel O
dg3dst 03/#545,D2=RA on | 14=2ndTrqCrv,15=DiagReq,
d_in_h1_function 13DA 3 = external stop engine input 13 = external
stop engine input 1 O dh1dst 09/#523,D2=2SpdGov | 16=altVSGoff,17=brk off,
d_in_h2_function 13DB 5 = parking brake5 = parking brake O
dh2dst 10/#524,D2=ParkBrk | 18=Clutch off,19=SC off,
d_in_j1_function 13DC 20 = set/coast20 = set/coast O dj1dst
01/#541,D2=SC on | 20=SC on,21=RA off,22=RA on,
d_in_j2_function 13DD 18 = clutch released18 = clutch released O
dj2dst 05/#531,D2=BC on | 23=CrzEnb,24=PGSenb,25=STEO,
d_in_k2_function 13DE 2 = jake brake 42 = jake brake 4 O dk2dst
11/#583,D2=CrkPos | 26=EBenb,27=n/a,28=TPSadj,
d_in_k3_function 13DF 1 = jake brake 21 = jake brake 2 O dk3dst
12/#979,D2=Tach#2 | 29=A/COff,30=EatonRes ...42
d_out_a1_function 13E0 10 = coolant low10 = coolant low O da1src
08/#988,D2=EBenb | 0=none,1=EB low,2=EB med,
d_out_a2_function 13E1 13 = fan clutch control 113 = fan clutch
control 1 O da2src 02/#555,D2=CCact | 3=LowBatt,4=Sync,5=PGS,
d_out_f3_function 13E2 6 = ignition relay6 = ignition relay O
df3src 01/#499,D2=VspdOC | 6=PwrShut,7=Starter,8=EBenb,
d_out_fet_timer 13E3 40.0 uSC 28 E V
dptupl low side unprotected driver settling time
d_out_highside_timer 13E4 4.99 mSC 27 E*7.8125 V
dptprh high side protected driver settling time
d_out_lowside_timer 13E5 99.8 mSC c3 E*1.95313 V
dptprl low side protected driver settling time (CEL)
d_out_s3_function 13E6 2 = jake brake 42 = jake brake 4 E ds3src
03/#561,D2=n/a (Hi) | 9=TranRtdr,10=CLlow,11=Crz,
d_out_t3_function 13E7 1 = jake brake 21 = jake brake 2 E dt3src
04/#562,D2=n/a (Hi) | 12=n/a,13=Fan#1,14=Fan#2,
d_out_w3_function 13E8 0 = no function0 = no function O dw3src
05/#563,D2=n/a | 15=Decel,16=EBact,17=VSGact,
d_out_x3_function 13E9 0 = no function0 = no function O dx3src
06/#564,D2=n/a | 18=OPlow,19=OThi,20=CThi,
d_out_y3_function 13EA 0 = no function0 = no function O dy3src
07/#565,D2=n/a | 21=AirCmp,22=CCPhi,23=CPlo..
db_brake_fan_delay 13EB 5.0 SEC 05 E V
dbdly EngBrks ON > DBDLY secs to allow DYNAMIC BRAKING
debounce_timeout 13EC 0.050 SEC 02 E*40 V
didbnc Digital Input switch debounce time in seconds
default_timeout 13ED 2.0 SEC 14 E*10 V
didftm global default secs fault must exist to log code
dmy_j1939_engine_address 13EE 255.0 N/A ff E B
dhieng VEPS backward compat. for J1939 engine address
dmy_j1939_retarder_address 13EF 255.0 N/A ff E B
dhiret VEPS backward compat. for J1939 retarder address
door_offset_filterconst 13F0 0.000 % @ 00 E*128 V
tboffc Blower Door Position filter constant
double_rpm_enable_delta 13F1 25.0 RPM 19 E V
dblenb DBLRPM hysteresis:RPM>DBLRPM+DBLENB to enable
dp_idle_recal_timer 13F2 1.5 sec 03 E*2 B
dpidrt in this period perform sensor cnt readings & check
dual_to_single_turbo_delay 13F3 3.0 SEC 06 E*2 V
dtstd Time delay before trans from Dual to Single turbo
dvb_battery_offset 13F4 0.0180 D/V= 12 E*1000 V
dvbbat DVB %PWM DtyCycl Offset=DVBOFF*(1+DVBBAT*(Vbat-13)
dvb_dc_filterconst 13F5 0.047 % @ 06 E*128 V
dvbfic %DC Lag/Lead fltr for trans solenoid self-heat cmp
dvb_gain 13F6 0.00270 O/C 36 E*20000 V
dvbgan SS %PWM duty cycle=I(desired)*R(total)/Vbat+Offset
dvb_lag 13F7 0.1490 MLT 26 E*255 V
dvblag Actual %PWM duty cycle = DVBPAS * SS%dc + ...
dvb_passthru 13F8 0.8510 MLT d9 E*255 V
dvbpas ... DVBFIC(@10sec) * DVBLAG * Last%dc
dvb_pwm_offset 13F9 2.8 %DC 1c E*10 V
dvboff Base DVB %PWM duty cycle offset @ Vbat=13 volts
dvb_resistance 13FA 2.70 OHM 36 E*20 V
dvbohm R(total)=DVBOHM*(1+DVBGAN*(OilTmp-20degC)
egr_air_temp_hyst 13FB 0.0 dgC 00 E*0.9 B
egrott hyst for min/max intake air temp, offset EGRATT
egr_boost_mode_max_egr_flow 13FC 0.00 kg/m 00 E*16 B
egrbmf max allowable EGR flow during intake boost press
egr_clt_temp_hyst 13FD 0.0 dgC 00 E*0.9 B
egroct hyst for min/max eng cool temp, offset of EGRCTT
egr_density_correction 13FE 0.000 "" 00 E*64 B
egrden density correction factor applied to EGR flow calc
egr_flow_diag_critical_time 13FF 127.5 sec ff E*2 B
egrfrs max time turbo is flag nonrespon while EGR ctrl
egr_in_boost_mode_time 1400 127.5 sec ff E*2 B
egrbmt max time cal amt of EGR flow is sensed while boost
egr_max_flow_response_time 1401 127.5 sec ff E*2 B
egrfrt max time EGR err is outside bounds while EGR ctrl
egr_max_vane_pwm 1402 100.0 % c8 E*2 B
egrmxv max dc for VNT vanes actuator when ctrl EGR flow
egr_min_boost_hyst 1403 0.0 kPa 00 E*1.15992 B
egrmnh hyst used with EGRMNB
egr_min_flow 1404 0.00 kg/m 00 E*16 B
egrmnf min allowable EGR flow during EGR flow ctrl mode
egr_min_flow_response 1406 0.00 kg/m 0000 E*16 B
egrmfr min EGR flow delta for desired and actual dur EGR
egr_min_flow_time 1408 127.5 sec ff E*2 B
egrfmt max time EGR flow is below cal level while in EGR
egr_min_vane_pwm 1409 0.0 % 00 E*2 B
egrmnv min dc for VNT vanes actuator when ctrl EGR flow
engine_m_inertia 140A 0.00049 T/R/ 01 E*2047 V
eminrt engine's inertia used for DAD governor compensatn
ess_accel_filter_constant 140B 0.016 frac 02 E*128 V
essafc Output shaft RPM d/dt filter constant
ess_autorange_prediction_time 140C 1.000 Sec 28 E*40 V
essapt Auto range increment for derivative comparison
ess_base_engine_zero_tq_loss 140D 0.39 %tq 01 E*2.55 V
essezl Average parasitic loss contribution due to engine
ess_base_vehicle_zero_tq_load 140E -0.24 %tq fffffffd E*12.75 V
essvzl Average torque load due to vehicle
ess_boost_torque_factor 140F 0.000 %tq/ 00 E*163.2 V
essbtf Contribution of turbo boost to estimated zero tq.
ess_break_tq_cold_factor 1410 0.0000101 %tq/ 0f E*1485483 V
essbcf Contribution factor of eng. temp. to est. zero tq.
ess_break_tq_duration 1411 2.000 Sec 50 E*40 V
essbtd Max. time break tq. operation is allowed
ess_break_tq_eng_uncertainty 1412 3.92 %tq 0a E*2.55 V
essbeu Uncertnty gain fact. for tq dither frm eng inertia
ess_break_tq_veh_uncertainty 1413 0.31 %tq 04 E*12.75 V
essbvu Uncertainty gain fact for tq dither from veh inert
ess_debounce_timeout_in_gear 1414 5.0 "" 01 E/5 V
essdtg The debounce time for the in gear switch
ess_debounce_timeout_neutral 1415 5.0 "" 01 E/5 V
essdtn The debounce time for the neutral switch
ess_idle_rpm_percent_below 1416 14.84 % 26 E*2.56 V
essirp Percentage that idle RPM is lowered
ess_in_gear_duration 1417 0.200 Sec 08 E*40 V
essigd Time before in-gear is given by a valid gear ratio
ess_in_gear_fault_decrement 1418 3.0 "" 03 E V
essgfd ***** NOT USED *****
ess_in_gear_fault_threshold 1419 30.0 "" 1e E V
essgft ***** NOT USED *****
ess_intermediate_timeout 141A 3.000 "" 78 E*40 V
essit ***** NOT USED *****
ess_max_late_changes 141B 7.0 Coun 07 E V
essmlc Max. number of late changes allowed on a shift
ess_neutral_duration 141C 0.100 Sec 04 E*40 V
essnd Time before neut is indicatd aftr an invlid gr rat
ess_neutral_fault_decrement 141D 3.0 "" 03 E V
essnfd ***** NOT USED *****
ess_neutral_fault_threshold 141E 30.0 "" 1e E V
essnft ***** NOT USED *****
ess_range_down_duration 141F 0.750 Sec 1e E*40 V
essrdd Time a synchrnzr req to compl. a range down shift
ess_range_protection_duration 1420 0.100 Sec 04 E*40 V
essrpd Synch. time req'd on range shift to protct synchro
ess_range_up_duration 1421 0.250 Sec 0a E*40 V
essrud Time synchronizer needs to compl. a range up shift
ess_rated_rpm_percent_above 1422 10.16 % 1a E*2.56 V
essrrp The percentage the rated RPM is increased
ess_ratio_check_timeout 1423 0.350 SEC 0e E*40 V
essrct SECs ratio allowed to match gear during downshift
ess_ratio_filter_constant 1424 0.203 frac 1a E*128 V
essrfc Filter constant for the current gear ratio calc.
ess_ratio_match_tolerance 1425 4.980 % 66 E*20.48 V
essrmt Tolernce for gr. mtch betwn act. and calc. gr. rat
ess_rpm_filter_constant 1426 0.203 frac 1a E*128 V
essrf Filter constant for filtering requested RPM
ess_rpm_tq_dither_eng_uncert 1427 3.92 %Tq 0a E*2.55 V
essufg The uncertainty gain for tq dither for eng inertia
ess_rpm_tq_dither_engine_loss 1428 5.88 %Tq 0f E*2.55 V
esserl Average parasitic loss contribution due to engine
ess_rpm_tq_dither_veh_uncert 1429 0.31 %Tq/ 04 E*12.75 V
essdvu Uncertainty gain for the tq dither for veh inertia
ess_rpm_tq_dither_vehicle_load 142A -0.39 %Tq/ fffffffb E*12.75 V
essdvl Average tq load due to vehicle
ess_sec_chance_prediction_time 142B 1.000 Sec 28 E*40 V
essscp Time appld to d/dt(RPM) to determine sec chnc gr
ess_shift_delay_time 142C 0.275 Sec 0b E*40 V
esssdt Time sync cont aftr in gr to lmt partial engagmt
ess_shift_knob_timeout 142D 1.000 Sec 28 E*40 V
essskt Max time allwd for shft knob swtch inpt to stablze
ess_skip_shift_disable_timeout 142E 0.100 Sec 04 E*40 V
esssst Time skp shft is disabld due to chng of intent sw
ess_stuck_in_gear_increment 142F 3.0 Coun 03 E V
esssgi Weighting for ech stck in gr occurnce for faulting
ess_stuck_in_gear_threshold 1430 30.0 Coun 1e E V
esssgt ESS lckout thrshld fr too many stck in gr occurnce
ess_stuck_in_gear_torque 1431 20.00 %Tq 33 E*2.55 V
essstq Tq load above which a stuck in gear is detected
ess_sync_timeout 1432 3.000 Sec 78 E*40 V
essst Amount of time engine synching is allowed
ess_torque_filter_constant 1433 0.203 frac 1a E*128 V
esstfc Fltr const for govrnor tq frm whch to begn transtn
ess_torque_transition_duration 1434 0.350 Sec 0e E*40 V
essttd Time to switch from first to next torque_transitio
ether_air_temp_weight 1435 0.4314 MLT 6e E*255 V
eiatw EtherTemp = (AirTemp*eiatw + CoolTemp*eictw + . .
ether_block_delay 1436 1.0 SEC 0a E*10 V
eibdly RPM>eimin for eibdly secs before block ether inj
ether_cool_temp_weight 1437 0.1333 MLT 22 E*255 V
eictw . . . OilTemp*eiotw) / (eiatw + eictw + eiotw)
ether_oil_temp_weight 1438 0.4314 MLT 6e E*255 V
eiotw . . . see above comment
exh_overtemp_divisor 1439 1.00 unit 10 E*16 B
exotdv divides result of exh temp-scaled hi for otp
exhaust_bp_limit_rampdn_delta 143A 3.45 kPa 08 E*2.31985 V
ebprpm additive offset to EBPLIM as a rampdown threshold
exhaust_bp_scaledlo_exclusion 143B 0.0 tq*r 00 E/10 V
ebpftq threshold above which a scaledlolimit is logged
fan_ac_mph_exclusion 143C 20.0 MPH 28 E*2 V
fnacex MPH>fnacex to clip ACTIM and disable fan
fan_air_div 143D 1.00 DIV 04 E*4 E
fnardv PWM FAN temp error = (AirTemp-ATFPWM)/FNARDV
fan_air_temp_minimum_torque 143E 30.20 %TQ 4d E*2.55 V
fatntq %FTQ>fatntq for AirTemp to enable digital+PWM fan
fan_cooler_div 143F 1.00 DIV 04 E*4 E
fncodv PWM FAN temp error = (CoolTemp-CTFPWM)/FNCODV
fan_delay 1440 0.5 SEC 05 E*10 V
fandly FanCtrl#1+#2 off for fandly SEC for 1:1 spd switch
fan_transition_low_spd_time 1441 15.0 "" 1e E*2 B
fantlt fan_transition_low_spd_time
fan_min_on_time 1442 30.0 SEC 1e E V
fanont minimum seconds that fan(s) are ON for all reasons
fan_oil_div 1443 1.00 DIV 04 E*4 E
fnoldv PWM FAN temp error = (OilTemp-OTFPWM)/FNOLDV
fan_ramp_rate 1444 10.0 %/S 14 E*2 E
fpwrmp maximum PWM FanControl %DC increase in %DC per SEC
fan_type 1445 1 = single fan1 = single fan E fantyp
FanCtrl: 1=1fan1spd 2=2fan1spd 3=1fan2spd
filtq_en_threshold 1446 0.50 degr 04 E*8 V
flteth If BOI cmpnstions < flteth filt tq will offset BOI
filtq_min_boi 1447 -3.00 degr fffffff4 E*4 B
fltmnb minimum BOI allowable when filt torque is active
fire_pump_press_threshold 1448 41.4 kPa 03 E/13.794 V
fwppbt if fire pump press below fwppbt, bcast zero ppress
first_cylinder_in_block 1449 1.0 DEC 00 E-1 V
fstcyl MultiBlock: Risetime code cyl ID = cyl# + fstcyl
friction_tq_loss_fan_adder 144A 5.10 %tq 0d E*2.55 V
ftqlfa TQLOST adder to J1939 msg when fan in ON
gain_ramp_time 144B 10.0 SEC 0a E V
gvgntm secs into run mode to ramp GAIN gvomin to gvogva
glowplugs_cycle_timeout 144C 112.0 SEC 70 E V
gptim IGN ON time>gptim & OilTp & FTQ for glow plugs OFF
glowplugs_max_torque 144D 20.00 % 33 E*2.55 V
gppct FTQP>gppct*ztqscl & OilT & Timr for glow plugs OFF
glowplugs_noTRS_timeout 144E 240.0 SEC f0 E V
gpztm time since last TRS>gpztm then glow plugs disabled
gov_diff_gain 144F 0.0000124 (T*S 0d E*1048576 V
gvdfgn governor gain: DIFFERENTIAL in %TQ*SEC/RPM
gov_integr_gain 1450 0.0049 T/(R 05 E*1024 V
gvingn governor gain: INTEGRAL in %TQ/(RPM*SEC)
gov_lag_gain 1451 3.00 MLT 30 E*16 V
gvlggn governor gain: LAG
gov_lead_gain 1452 4.00 MLT 40 E*16 V
gvldgn governor gain: LEAD
gov_overall_gain 1453 2.00 MLT 20 E*16 V
gvovga governor gain: OVERALL ADJUSTMENT
gov_overall_gain_max 1454 2.00 MLT 20 E*16 B
gvoamx gvovga <= gvoamx for customer cal changes
gov_overall_gain_min 1455 2.00 MLT 20 E*16 B
gvoamn gvovga >= gvoamn for customer cal changes
gov_overall_start_gain 1456 0.50 MLT 08 E*16 V
gvomin initial overall gov gain when run mode entered
gov_prop_gain 1457 0.00098 T/R 10 E*16384 V
gvprgn governor gain: PROPORTIONAL in %TQ/RPM
halfeng_enable 1458 0.0 "" 00 E D
heenb 0-never, 1-at any temperature, 2-using max_oilt
halfeng_offset_boi 1459 0.00 Deg. 00 E*4 B
heoffb BOI offset added to base table when in halfeng
halfeng_max_mph 145A 5.0 MPH 0a E*2 V
hemxvs vehicle MPH > HEMXVS then HALF ENGINE disabled
high_alt_minimum_pressure 145B 50.0 KPA 3a E*1.15992 V
hamnbp BARO below which HIGH ALTITUDE TQ limiting occurs
high_alt_minimum_torque 145C 100.00 %TQ ff E*2.55 V
hamntq min TQ allowed by HIGH ALTITUDE TQ limiting
high_alt_pressure_gain 145D 0.0079 %/K 07 E*882.816 V
haprtq HIGH ALT TQ limiting gain applied to HAMNBP-BARO
high_temp_min_run_time 145E 30.0 SEC 1e E V
htpmrt RPM>minrpm for htpmrt SECs for high temp code
idle_gov_init_int 145F 3.92 % 0a E*2.55 V
idlii idle governor: Initial INTEGRATOR value (*ztqscl)
idle_off_min_throttle 1460 120.0 A/D 3c E/2 V
tmxeni TPS A/D<tmxeni then idle val switch should be ON
idle_on_max_throttle 1461 282.0 A/D 8d E/2 V
tmneis TPS A/D>tmneis then idle val switch should be OFF
idle_override_exit_time 1462 10.0 SEC 0a E V
isotm TPS>0% after isotm then IDLE SHTDWN OVERRIDE reset
idle_speed_max_offset 1463 100.0 RPM 64 E V
iofmax maximum idle offset speed
idle_speed_min_offset 1464 -25.0 RPM ffffffe7 E V
iofmin minimum idle offset speed
ignition_off_time 1465 2.0 SEC 14 E*10 V
igofft IGN off>igofft AND no TRS then ign cycle has ended
inactive_max_pw 1466 5.0 DEG 05 E V
ishpw Final PW<ishpw for Brick on Throttle IDLE SHTDWN
inactive_min_pw 1467 0.0 DEG 00 E V
islpw Final PW>islpw for Brick on Throttle IDLE SHTDWN
inactive_timeout 1468 1200.0 SEC 78 E/10 V
isbtm Brick on Throttle IDLE SHUTDOWN Timer
initialize_ram_value 1469 0.0 "" 00 E V
iramv Value to set uninitialized RAM to on reset
injector_adjust_max 146A 0.0700 % 46 E*1000 V
ijcmax max %PW increase that may be applied to a cylinder
injector_adjust_min 146B 0.0700 % 46 E*1000 V
ijcmin max %PW decrease that may be applied to a cylinder
injector_filterconst 146C 0.125 % @ 10 E*128 V
irtfc injector response time filter constant
injector_timeout 146D 5.0 SEC 32 E*10 V
irttmo ramp/reset timer SECS to log rise time long/short
j1587_default_output_count 146E 25.0 DEC 19 E V
jlornm J1587:Number of DDEC unique response transmissions
j1587_default_output_interval 146F 0.200 SEC 08 E*40 V
jlortm J1587:Interval between DDEC unique response trnsms
j1587_engine_mid 1470 128.0 MID 80 E V
jlomid J1587: Engine Message IDentifier
j1708_retry_count 1471 5.000 SEC c8 E*40 V
jretry J1708: Seconds of retries before reporting fault
j1922_engine_output_interval 1472 0.050 SEC 02 E*40 V
jlootm J1922: Time between engine to powertrain messages
j1922_override_timeout 1473 1.000 SEC 28 E*40 V
jlotmx J1922: Timeout for J1922 override commands
j1922_retarder_output_interval 1474 0.100 SEC 04 E*40 V
jreotm J1922: Time between retarder to pwrtrain messages
j1939_engine_address 1475 0.0 Adr 00 E V
jhieng J1939: engine souce/dstntion address: 0=on/255=off
j1939_engine_timeout 1476 0.050 SEC 02 E*40 V
jhieto J1939: Timeout for engine control commands in SECs
j1939_ftq_input_source_address 1477 255.0 J193 ff E V
jhtqsa Source addr of device that will slew final tq
j1939_override_timeout 1478 2.000 SEC 50 E*40 V
jhitmx J1939: Timeout for J1939 override commands in SECs
j1939_retarder_address 1479 15.0 Adr 0f E V
jhiret J1939: retarder src/dstntn addr: 15=EngBrk/255=off
j1939_retarder_timeout 147A 0.125 SEC 05 E*40 V
jhirto J1939: Timeout for retarder cntrl commands in SECs
j1939_transmission_address 147B 255.0 Adr ff E O
jhitrn J1939: transmission src/dstntion address / 255=off
j1939_transmission_timeout 147C 0.050 SEC 02 E*40 V
jhitto J1939: TimeOut for transmission's control commands
jake_brake_hysteresis 147D 1.00 MPH 10 E*16 V
jbhyst (veh MPH-cc set MPH)<jbXmph-jbhyst then lower jake
jake_brake_min_mph 147E 0.0 MPH 00 E*2 D
jbmph vehMPH > jbmph to enable jake brakes - R5(Own)=DDR
jake_hi_delta_mph 147F 7.00 MPH 70 E*16 D
jbhmph (veh MPH-cc set MPH)>jbhmph then high jake brake
jake_lo_delta_mph 1480 3.00 MPH 30 E*16 D
jblmph (veh MPH-cc set MPH)>jblmph then low jake brake
jake_med_delta_mph 1481 5.00 MPH 50 E*16 D
jbmmph (veh MPH-cc set MPH)>jbmmph then medium jake brake
jake_peak_retardation 1482 1288.0 N*m 5f E/13.558 V
jbpktq J1922: rtrdr to pwrtr msg jakebrk pk retarding trq
jake_turnoff_delay 1483 0.100 SEC 04 E*40 V
jbtodl time to suppress fueling after jake brake disabled
kickd_min_tps 1484 94.90 %TPS f2 E*2.55 V
tmnakd Not Used
kickd_off_max_throttle 1485 0.0 A/D 00 E/2 V
tmnenk Not Used
kickd_on_min_throttle 1486 0.0 A/D 00 E/2 V
tmxekd Not Used
konst_peak_retardation 1487 854.2 N*m 3f E/13.558 V
knpktq J1922: rtrdr to pwrtr msg S55 KD peak retarding TQ
limit_toofew_srs 1488 50.0 % 32 E V
limtfs % of nomsrs cam revs with no SRS to log TooFewSRS
limit_toomany_srs 1489 50.0 % 32 E V
limtms % of nomsrs cam revs with 2FewTRS to log 2ManySRS
lock_by_errors 148A 3.0 DEC 03 E V
lckerr # SRS/TRS errors before locking tooth_error_times
lookup_interval 148B 150.0 RPM 96 E V
lkint step between cal table RPM points:S30G=250,else150
low_coolant_slosh_timer 148C 30.0 SEC 1e E V
lcstim Low Clnt Lvl DigIn low for lcstim to enable DigOut
low_cool_press_min_boost 148D 0.00 KPA 00 E*2.31985 V
cptbmn Boost kpa > CPTBMN to log low coolant pressure
low_cool_press_min_timer 148E 10.0 SEC 0a E V
cptbtm SECs that boost kpa > CPTBMN for low coolant press
low_cool_pressure_time_delay 148F 10.0 SEC 0a E V
coptd RPM>MINRPM for >COPTD secs to log low coolnt press
low_gear_tq_limiting_speed 1490 20.0 mph 28 E*2 B
lgtqls vehicle speed below which low gear tq limit isused
low_oil_pressure_time_delay 1491 10.0 SEC 0a E V
olptd RPM>MINRPM for >OLPTD secs to log low oil pressure
marine_torque_limit_end_time 1492 190.0 SEC be E V
tqtret %TQ>DTQLMT(RPM) for tqtret SECs for max %TQ lmtg
marine_torque_limit_count_rate 1493 2.0 S/S 14 E*10 V
tqtcdr %TQ lmtg timer decrement in SECs/SEC if %TQ<DTQLMT
marine_torque_limit_start_time 1494 180.0 SEC b4 E V
tqtrst %TQ>DTQLMT(RPM) for tqtrst SECs to start %TQ lmtg
marine_torque_limit_warn_time 1495 60.0 SEC 3c E V
tqtwtm %TQ>DTQLMT(RPM) for tqtwtm SECs for ChkEngLt warng
max_pwrdown_time_after_eeprom 1496 20.0 sec 14 E V
mpdtae max time ECM is on before low pwr mode when EEPROM
maximum_coasting_percentage 1497 39.84 % 66 E*2.56 B
dpmcp % max RPM below which engine is coasting
min_boi 1498 0.00 DEG 00 E*8 V
minboi minimum BOI (before multiplier)
min_bulb_on_time 1499 2.0 SEC 14 E*10 V
dimont minimum check and stop engine light ON time in sec
minimum_coast_speed 149A 40.0 MPH 50 E*2 B
dpmcs Minimum vehicle speed allowed for coasting
mf_major_delta_boi 149B 10.00 dg 50 E*8 V
mfmjdb BOI offset added to minimum boi when in major misf
mf_minor_delta_boi 149C 5.00 dg 28 E*8 V
mfmndb BOI offset added to minimum BOI when in minor misf
mf_minor_exit_time 149D 5.0 sec 32 E*10 V
mfmnet exit minr msf whn mfmnde<accl rt<mfmnae for mfmnet
mf_minor_to_major_count 149E 12.0 coun 0c E V
mfmtmc major misfr if minor misfire occurs mfmtmc times
mm_afrs_max_engine_hours 149F 72.0 Hour 48 E V
mmamxh Max eng hrs aftr drty fltr to recheck AFRS
mm_afrs_max_pressure 14A0 18.00 inH2 5a E*5 V
mmafmp Max pressure above which the air filt. is dirty
mm_afrs_min_engine_hours 14A1 24.0 Hour 18 E V
mmamnh Min eng hrs aftr drty fltr to recheck AFRS
mm_afrs_quantised_high 14A2 25.00 inH2 7d E*5 V
mmafqh AFRS upper trip point for quantized comms
mm_afrs_quantised_low 14A3 18.00 inH2 5a E*5 V
mmafql AFRS lower trip point for quantized comms
mm_ecm_awake_time 14A4 120.0 Minu 78 E V
mmeawk Time after ignition off for ecm to stay awake
mm_flash_time 14A5 15.0 Seco 0f E D
mmflsh Time aftr bulb chk for CEL/SEL to flash at ign on
mm_oil_drip_time 14A6 3.75 Minu 0f E*4 V
mmodpt Min. time after eng. has stopped to check OLS
mph_gov_disable_delta 14A7 10.0 MPH 0a E V
rsgdsb (rd spd lmt-veh MPH)>rsgdsb thn disable rd spd gov
mph_gov_enable_delta 14A8 8.0 MPH 08 E V
rsgenb (rd spd lmt-veh MPH)<rsgenb then enable rd spd gov
ms_comms_error_time 14A9 1.000 SEC 28 E*40 V
cerrtm J1939 timeout: BOI&PW for slave, 1/2eng for master
no_of_customer_cal_changes 14AA 4.0 DEC 04 E S
nccchg # of Customer Programming changes made to the CAL
no_of_injector_cal_changes 14AB 0.0 DEC 00 E S
nicchg # of Injector Calibration changes made
no_of_slaves 14AC 0.0 DEC 00 E V
msnslv Total number of slave ECMs
noise_b 14AD 0.0 RPM/ 00 E/2 B
noiseb Offset for noise acceleration limit calculation
noise_boi 14AE 14.00 degr 70 E*8 B
nsboi BOI when noise ctrl active and cool temp > cal
noise_control_distance 14AF 85.0 FT 55 E V
ncdist feet to reach rated RPM once noise control active
noise_disable_throttle 14B0 40.00 %TH 66 E*2.55 V
ntpdis %Throttle<ntpdnb disables Noise Control
noise_enable_throttle 14B1 98.04 %TH fa E*2.55 V
ntpenb %Throttle>ntpenb to enable Noise Control
noise_high_gear_dist 14B2 110.0 feet 6e E V
nchgdt noise control high gear distance
noise_m 14B3 0.000 "" 00 E*127 B
noisem Slope for noise acceleration limit calculation
noise_range_time 14B4 3.0 SEC 06 E*2 V
nrngtm RPM within noise range for >NRNGTM for noise cntrl
noise_rpm_fraction 14B5 0.6667 "" aa E*255 B
nrpmfr Fraction of rated speed for noise control
noise_vehicle_speed 14B6 8.5 MPH 11 E*2 B
nsvss Minimum vehicle speed to enable noise control
nox_adapt_1min_enter_time 14B7 10.0 sec 0a E V
na1ent time 1min rol avg load > nxlmt1 before adv to ss
nox_adapt_1min_exit_time 14B8 0.0 sec 00 E V
na1ext time 1min rol avg load < nxlmt1 before ret to base
nox_adapt_1min_limit 14B9 0.8510 Load d9 E*255 B
nxlmt1 % load for ATP reset if 1 min. rolling ave. is en
nox_adapt_2min_limit 14BA 0.7490 Load bf E*255 B
nxlmt2 % load for ATP reset if 2 min. rolling ave. is en
nox_sampling_interval 14BB 1.0 SEC 0a E*10 V
nxsmp Adptv Tmng: NOx cntrl RPM sampling interval in sec
oi_loop_debounce_time 14BC 150.0 Mill 96 E V
oildbt additional debounce time for OI safety loop
oil_press_zero_rpm_wait_time 14BD 3.0 sec 1e E*10 V
olpwtm time when engine rpm 0 before check for ops fail
optimum_load_curve_max_tq_dc 14BE 5.10 % du 0d E*2.55 V
olcxdc pwm percent duty cycle for fully overloaded signl.
optimum_load_curve_min_tq_dc 14BF 94.90 % du f2 E*2.55 V
olcndc PWM DC% at minimum underloaded torque
optimum_load_curve_nom_tq_dc 14C0 49.80 % du 7f E*2.55 V
olcnom PWM DC% at optimum load
optimum_load_dc_at_idle 14C1 49.80 % du 7f E*2.55 V
olcidc PWM DC% on idle governor
optimum_load_dc_in_start 14C2 49.80 % du 7f E*2.55 V
olcsdc PWM DC% in start mode
otp_cel_delta_coolant_temp 14C3 0.00 dgC 00 E*14.4 E
otdtco Dlta tmp>scldhi to brdcst msg & ilum CEL for OTP
otp_cel_delta_cylhead_temp 14C4 0.00 dgC 00 E*14.4 V
otdtcy Dlta tmp>scldhi to brdcst msg & ilum CEL for OTP
otp_cel_delta_ex_temp 14C5 0.00 dgC 00 E*14.4 V
otdtex Dlta tmp>scldhi to brdcst msg & ilum CEL for OTP
otp_cel_delta_inner_temp 14C6 0.00 dgC 00 E*14.4 V
otdtin Dlta tmp>scldhi to brdcst msg & ilum CEL for OTP
otp_cel_delta_oil_temp 14C7 0.00 dgC 00 E*14.4 V
otdtoi Dlta tmp>scldhi to brdcst msg & ilum CEL for OTP
otp_cel_delta_tco_temp 14C8 0.00 dgC 00 E*14.4 E
otdtct Dlta tmp>scldhi to brdcst msg & ilum CEL for OTP
otp_cel_delta_trans_temp 14C9 0.00 dgC 00 E*14.4 V
otdttr Dlta tmp>scldhi to brdcst msg & ilum CEL for OTP
otp_coolant_filter_constant 14CA 0.148 % @ 13 E*128 V
otpcfc filter const. appld to coolnt tmp for OTP
park_brake_temp_weighting 14CB 0.000 unit 00 E*128 V
pbtwfc temperature weighting factor for BOI calculation
ps_activate_lower_tps 14CC 5.0 %TPS 05 E V
psltps lower tps used in passing speed activation seq
ps_activate_upper_tps 14CD 95.0 %TPS 5f E V
psutps upper tps used in passing speed activation seq
ps_activation_cancel_timer 14CE 3.0 SEC 03 E V
psactc time w/in ps activation seq must complete
ps_activation_speed_timer 14CF 20.0 SEC 14 E V
psacts time w/in vehicle speed must > road speed limit
ps_cel_flash_time 14D0 60.0 SEC 3c E V
pscelt time before ps deactivation that CEL will flash
ps_increment 14D1 0.0 MPH 00 E D
psincr increment above road speed limit when ps active
ps_passing_duration 14D2 0.0 Minu 00 E D
pspdur min per interval that ps feature is allowed
ps_ramp_down_time 14D3 5.0 SEC 05 E V
psrdtm time for ramp down to road speed limit wh ps deact
ps_reset_interval 14D4 8.0 Hour 08 E D
psrint number of hours before passing duration is reset
pss_mph_hysteresis 14D5 2.00 MPH 20 E*16 V
pshyst PROG SHIFT: vehicle speed hysteresis in MPH
pss_range1_mph 14D6 26.0 MPH 34 E*2 D
psmph1 PROG SHIFT: max vehicle speed (MPH) in range 1
pss_range2_mph 14D7 44.0 MPH 58 E*2 D
psmph2 PROG SHIFT: max vehicle speed (MPH) in range 2
pss_range3_mph 14D8 45.0 MPH 5a E*2 D
psmph3 PROG SHIFT: max vehicle speed (MPH) in range 3
pto_hysteresis 14D9 8.0 A/D 08 E V
pthysc PTO: hysteresis A/D counts added to impulse output
pto_maximum_mph 14DA 3.0 MPH 06 E*2 E
ptmxvs PTO: vehicle MPH < ptmxvs to allow PTO operation
pto_maximum_tps 14DB 3.92 %TPS 0a E*2.55 E
ptztps PTO: TPS>ptztps then PTO disabled
radiator_temp_threshold 14DC 90.0 dgC c2 (E+17.78)*1.8 V
radthr CLS: temp thermostats open-for radiator temp calc
rail_p_low_protect_timeout 14DD 0.500 sec 14 E*40 V
rplprt timeout threshold for rplprd timer
range_breakpoint_gear_index 14DE 4.0 "" 04 E O
essrbi Highest gr in the low rnge for the given transmssn
rating_override 14DF 0.0 Flg 00 E D
ratovr >3 use RTG SWs else TPS & GOV rating var = ratovr
rating_version_number_shared 14E0 99.0 DEC 63 E B
rtvrsh Shared Ratings Version Number ID Only
ratings_allowed 14E1 63.0 DEC 3f E B
rallow bit 0-3=thr+gov rtgs,b4=rtg sw,b5=DDR set RATOVR
resume_hold_delay 14E2 1.000 SEC 28 E*40 V
resdly CC setpt inc'd ccincr&m/Xsec if r/a sw on>resdly
retarder_throttle_hysteresis 14E3 1.18 %TPS 03 E*2.55 V
trhyst %Throttle > trhyst to disable trans retarder
retarder_type 14E4 1 = jacob/PAC brake1 = jacob/PAC brake E
rettyp engine retarder type: 0=none 1=jakes 2=KD 3=DVB
road_speed_limit 14E5 75.0 MPH 96 E*2 D
rslmph RSG: maximum vehicle speed allowed by Road Spd Gov
sa_max_mph_delta 14E6 0.0 MPH 00 E*2 D
mphmxd max Fuel Economy Road Speed Limit increase in MPH
sa_mpg_cap 14E7 20.0 MPG 14 E V
mpgcap Max value for filtered MPG used in Driver Reward
sa_mpg_delta 14E8 3.0 MPG 1e E*10 V
mpgdlt MPGTHR+/-MPGDLT are max/min limits on filtered MPG
sa_mpg_threshold 14E9 7.0 MPG 46 E*10 D
mpgthr filtered MPG > MPGTHR to increase Road Speed Limit
sa_mph_to_mpg 14EA 5.0 M/M 32 E*10 D
mphmpg RSL MPH increase = (filtered MPG-MPHTHR)*MPHMPG
sensor_supply_err_timer_thresh 14EB 50.0 "" 32 E V
ssethr timer thresh at which ssv fault will be detected
sensor_supply_err_timer_weight 14EC 5.0 "" 05 E V
ssewgt counter inc when ssv is below calibrated setting
ss_temp_hyst 14ED 1.53 dgC 16 E*14.4 V
boisst Hysteresis used with temp cals to force BOISSR
tach_out_function 14EE 0 = tach drive output based on RPM0 = tach
drive output based on RPM V tacout Source for tach drive output. 0=RPM 1=PTO
set spd
tach_pulses_per_rev 14EF 12.0 puls 0c E V
tpprev number of pulses per rev that tach will output
turbo_min_tq_limit 14F0 40.00 "" 66 E*2.55 B
stmtql Min tq the PI controllers are allowed to req.
set_hold_delay 14F1 0.200 SEC 08 E*40 V
setdly CC inactive w/ setpt track if s/c sw on>setdly SEC
shift_detect_timeout 14F2 2.0 SEC 14 E*10 V
vrrwtm VGR: secs after gear shift that new=unfiltered VGR
shutdn_coolant_level 14F3 70.0 %CLS 8c E*2 V
discol CLS: CLS<discol for engine shutdown
shutdn_filterconst 14F4 0.063 Tau 08 E*128 V
setffc engine shutdown saved torque filter constant
shutdn_min_torque 14F5 40.00 %TQ 66 E*2.55 E
setmin eng shtdwn AND overtemp protect min allowed TORQUE
shutdn_oil_level 14F6 0.0 %OLS 00 E*2 V
disoll OLS: OLS<disoll for engine shutdown
shutdn_override_count 14F7 255.0 DEC ff E E
seocnt SEO: maximum number of shutdown overrides
shutdn_override_time 14F8 5.0 SEC 05 E V
seotmr SEO: time override OFF before recognized again
shutdn_ramp_time 14F9 30.0 SEC 1e E V
setimr ramp down time in secs before engine shutdown
single_turbo_delay_min_ltq 14FA 10.0 SEC 0a E V
stdmtq TQ < stmntq for stdmtq before switching to dual
single_turbo_max_ltq_hyst 14FB 5.10 %TQ 0d E*2.55 V
stmtqh Hyst when switching from dual to single turbo mode
single_turbo_maxltq_increment 14FC 150.0 RPM 96 E V
stmlin incremental RPM val usd to dfn rng of stmlmn
single_turbo_min_ltq_hyst 14FD 5.10 %TQ 0d E*2.55 V
stmnth Hyst tq used when switching from dual to single
srs_no_trs_limit 14FE 3.0 DEC 03 E V
srsnot SRS: #SRS>srsnot with No TRS to log Too Many SRS
steady_egr_load_hyst 14FF 0.00 % lo 00 E*2.55 B
segrlh engine load hyst for EGR win when in steady BOI
steady_egr_max_load 1500 0.00 % lo 00 E*2.55 B
segrxl max eng load hyst for EGR win when in steady BOI
steady_egr_min_load 1501 0.00 % lo 00 E*2.55 B
segrnl min eng load hyst for EGR win when in steady BOI
system_delay 1502 0.0 DEC 00 E V
sysdly #engine tq gen delay in cylinder firings
t2_cc_demand_max 1503 80.00 %TQ cc E*2.55 V
astcdm If %RTQ<ASTCDM upshift pt ramped down if in CC+9th
t2_cc_rampdown_time 1504 10.0 SEC 0a E V
astcrt normal to lower shiftpt rampdown SECs if in CC+9th
t2_dis_split_attempts 1505 3.0 DEC 03 E V
astdsa # of failed splitter attempts to log fault
t2_eng_time_increment 1506 0.050 SEC 02 E*40 V
asteti SECs added to engage timer if within diseng window
t2_kick_upshift_reset 1507 20.00 %TQ 33 E*2.55 V
astkur Minimum %torque to reset upshift point
t2_knee_ramp_rate 1508 1.96 %TQ 05 E*2.55 V
astkrr % knee tq ramp rate per 25ms after shift completed
t2_knee_torque 1509 20.00 %TQ 33 E*2.55 V
astktq Throttle ramp back torque transition point
t2_min_percent_torque 150A 20.00 %TQ 33 E*2.54998 V
astmpt Min % torque required to initiate an upshift
t2_offset_time 150B 4.000 SEC a0 E*40 V
astoft Time allowed to suppress shft pt after shft complt
t2_ramp_back_rate 150C 4.31 %TQ/ 0b E*2.55 V
astrbr % tq ramp rate per 25ms after shift has completed
t2_skid_confirmed_time 150D 0.100 SEC 04 E*40 V
astskt SKID conditions met for ASTSKT to confirm SKID
t2_skid_settling_time 150E 1.00 SEC 04 E*4 V
astost Disable T2 for ASTOST secs after skid for osciltn
t2_skid_timer_const 1510 400.0 %@25 0320 E*2 V
aststc Timer constant to cancel skid condition
t2_tq_ramp_dwn_rate 1512 10.0 %TQ/ 0a E V
asttrd Torque ramp down rate for approaching 0% torque
tas_alarm_time 1513 5.00 SEC 19 E*5 V
tasatm alarm secs=TASATM prior to any auto-start
tas_battery_switch_voltage 1514 18.0 VLT 12 E V
tasbsv Assume +24V charging system if Vbat>TASBSV
tas_battery_time 1515 120.0 Minu 3c E/2 V
tasbat OI battery run time for low battery eng. starts
tas_continuous_cycle_time 1516 15.0 MIN 0f E V
tascct auto-start after TASCCT mins if ISD w/ cabtemp bad
tas_crank_end_time 1517 8.00 SEC 28 E*5 V
tascet auto-start total crank secs<TASCET
tas_crank_max_vss 1518 2.0 PLS 02 E V
tasvss VSSpulses<TASVSS to continue auto-start cranking
tas_crank_oil_temp 1519 15.6 dgC 3c (E+17.78)*1.8 V
tascot OilTmp<TASCOT for auto-strt if ISD+intrlocks+alarm
tas_crank_rpm_time 151A 1.80 SEC 09 E*5 V
tascrt RPM>TASCMR in secs<TASCRT to continue auto-start
tas_initial_run_time 151B 45.0 MIN 2d E V
tasirt if start for CabTmp+CabTmp bad for TASIRT then ISD
tas_max_mph_safety 151C 3.0 MPH 03 E V
tasmph log code+disable TAS if VehSpd>TASMPH+safety loop
tas_restart_time 151D 45.0 SEC 2d E V
tasrst attempt 2nd auto-start TASRST secs after 1st ends
tas_rpm_ramp_rate 151E 50.0 R/S 32 E V
tasrrt RPM ramp rate to setRPM once run mode achieved
tas_rpm_switch_temp 151F 18.3 dgC 41 (E+17.78)*1.8 V
tastmp AmbTmp>TASTMP for TASSUM else TASWIN auto-setRPM
tas_shutdown_torque 1520 25.10 %TQ 40 E*2.55 V
tasstq engine shutdown if %TQ>TASSTQ with OI in control
tas_vehicle_power_delay 1521 30.0 SEC 3c E*2 V
tasdly VehPwrShtDwn ON TASDLY after CabTemp ato-strt only
tco_overtemp_divisor 1522 1.00 unit 10 E*16 V
tcootd div hightest tco temp to scale to overtemp protect
teeth_on_wheel 1523 36.0 DEC 24 E V
nteeth #TRS teeth: DDEC3(all eng)=36 / DDEC2(S60 only)=6
tooxxx_srs_count 1524 7.0 DEC 07 E V
nomsrs SRS: # camshaft revs used for SRS/TRS error tests
top_gear_1_min_road_speed 1525 25.0 MPH 32 E*2 B
dptg1s Speed to be exceeded before top gear - 1 recalced
tps_dec_filterconst 1526 0.203 % @ 1a E*128 V
tpdefc %TH offset decr filter const: new=old+tpdefc*(n-o)
tps_inc_filterconst 1527 0.008 % @ 01 E*128 V
tpinfc %TH offset incr filter const: new=old+tpinfc*(n-o)
tps_min_offset 1528 100.0 A/D 64 E V
tpomin TPS: minimum TPS offset in A/D counts
tps_offset_hyst 1529 52.0 A/D 34 E V
tpohis TPS OFFSET: new=min(old,max(new+tpohis,tpomin))
tqrpm_filterconst 152A 1.000 unit 80 E*128 V
tqrpfc filter constant used by filtered_tq exh bp calcs
transmission_type 152B 0.0 DEC 00 E O
txtyp Transmission ID, used for setting PWM1 at OEMs
trs_stop_time 152C 0.1 SEC 01 E*10 V
tnotrs TRS: secs w/ no TRS before RPM assumed to be 0
turbo_fix_pos 152D 0.0 %BBP 00 E*2 V
tbfix BLWR BYPS: position=tbfix if oil temp<tboilt
turbo_integr_gain 152E 1.00 DEC 10 E*16 V
tbdig BLWR BYPS: integral gain
turbo_overall_gain 152F 1.00 DEC 10 E*16 V
tbdlg BLWR BYPS: loop gain
turbo_overspeed_int_gain 1530 0.00782 %TQ/ 10 E*2047 V
tbosig Turbo overspeed integral gain
turbo_overspeed_prop_gain 1531 0.00782 %TQ/ 10 E*2047 V
tbospg Turbo overspeed proportional gain
turbo_position_gain 1532 2.03 %/K 1c E*13.794 V
tbposg BLWR BYPS: position gain in % position per kpa
turbo_pressure_offset 1533 0.0 KPA 00 E*1.15992 V
tbdelp TURBO: desired boost offset sbtrct from DESKPF Tbl
turbo_prop_gain 1534 0.63 DEC 0a E*16 V
tbdpg BLWR BYPS: proportional gain
twins_pulses_per_rev 1535 0.0 PPR 00 E E
tsppr SYNC: RPM synchronization mode pulses per rev
vgr_delta 1536 0.0703 RTO 12 E*256 V
vrdlta VGR: unfltrd/fltrd>1+/-vrdlta thn gear shift occrd
vnt_boost_diag_critical_time 1537 127.5 sec ff E*2 B
vntdct max time turbo is flag nonrespon while boost ctrl
vnt_default_pwm 1538 50.0 % 64 E*2 B
vntpwm default dc for VNT vanes actuator when ctrl notenb
vnt_max_boost_response_time 1539 127.5 sec ff E*2 B
vnmbrt max time boost press err is outside bnds while bst
vnt_min_boost_response 153A 0.0 kPa 00 E/1.72425 B
vntmbr min boost press delta for des & actual in bst ctrl
vnt_pid_min_load 153B 0.00 % lo 00 E*2.55 B
vntpml min engine load at which exhaust flow alg is enabl
vnt_pid_min_rpm 153C 0.0 rpm 00 E/10 B
vntpms min engine speed at which exhst flow alg is enabl
vnt_saturation_boost_time 153D 127.5 sec ff E*2 B
vntsbt max time VNT vanes are actuated at extreme pos bst
vnt_saturation_egr_time 153E 127.5 sec ff E*2 B
vntset max time VNT vanes are actuates at extreme pos bst
vnt_turbo_speed_thresh 153F 0.0 rpm 00 E/512 B
vnttst min turbo shaft speed err before turbo speed limit
vnt_vane_pos_change_limit 1540 400.0 "" c8 E/2 B
vntvpc max VNT vanes actuator %dc chg in 1sec T EGR/boost
vsg_qualification_timeout 1541 30.0 SEC 1e E V
vsgqto max SECs allowed to qualify a Dual VSG station
vsg_ramp_to_idle 1542 200.0 R/S 14 E/10 V
vsgrid RPM/SEC ramp down rate from VSG set speed to idle
vss_absolute_diagnostic_limit 1543 0.0 MPH 00 E*2 D
dimxv2 MPH>dimxv2 to log vehicle overspeed / 0 to disable
vss_driving_diagnostic_limit 1544 0.0 MPH 00 E*2 D
dimxv1 MPH>dimxv1 AND LTQ>0 to log fueld veh ovrspd/0=off
vss_fail_detect_mph 1545 3.0 MPH 06 E*2 V
vsfrs VSS: veh MPH<vsfrs to log veh spd sensor failed
vss_fail_detect_pw 1546 15.00 DEG 3c E*4 V
vsfpw VSS: PW>vsfpw to log veh spd sensor failed
vss_fail_timeout 1547 10.0 SEC 64 E*10 V
vsfto VSS: time (integrating) to log VSS failed
vss_filterconst 1548 0.500 Tau 40 E*128 V
vssfc VSS: vehicle speed filter constant
vss_idle_speed 1549 1.50 MPH 18 E*16 V
vssisp MPH when vehicle is considered at idle (no motion)
vss_idle_speed_hysteresis 154A 1.00 MPH 10 E*16 V
vssish MPH when veh is cnsdrd mvng = vssisd + vssish
vss_nox_adapt_exit_time 154B 10.0 SEC 0a E V
vnxext time in which vehicle < vnxmph before ret to base
vss_nox_adapt_mph 154C 50.0 MPH 64 E*2 V
vnxmph vehicle speed at which BOI is advanced to SS tbl
vss_nox_adapt_reenter_time 154D 10.0 SEC 0a E V
vnxret time in which vehicle > vnxmph before advan to ss
vss_pulses_per_rev 154E 16.0 Teet 10 E D
vssppr VSS: number of teeth used by VSS sensor
vss_tamp_power_down_time 154F 25.0 SEC fa E*10 V
vsspdt SEC w/ VSS fault AND no TRS before ECM power-down
vss_tamp_rpm_reset 1550 15.0 %RPM 0f E V
vsstrp %change in RPM>vsstrp to reset VSS tampering
vss_tamp_rslrpm_reset 1551 85.0 %RPM 55 E V
vsstrr %RPM<vsstrr of rslrpm to reset VSS tampering
vss_tamp_timeout 1552 2.0 SEC 14 E*10 V
vsstto VSS tampering fault timeout value
vss_tamp_vgr_delta 1553 5.0 %VGR 05 E V
vsstvd fltrd %VGRdelta>vsstvd to log VSS tampering fault
vss_tamp_vgr_reset 1554 15.0 %VGR 0f E V
vsstvr fltrd %VGRdelta>vsstvr to reset VSS tampering
vss_tamp_vss_delta 1555 15.0 %VSS 0f E V
vsstdl fltrd %VSSdelta>vsstdl to log VSS tampering fault
vss_timeout 1556 0.5020 SEC 80 E*255 V
vssout max SECs between VSS pulses before zeroed
vss_turbo_speed_filterconst 1557 0.203 Tau 1a E*128 V
vsstfc Turbo speed filter constant when using vss port
vss_turbo_pulses_per_rev 1558 1.0 Teet 01 E V
vtbppr Number of pulses per one turbo charger revolution
warmup_time 1559 240.0 SEC 3c E/4 V
warmtm TEMPs: eng run time to log temp sensor(s) fail hi
j1939_function_instance 155A 0.0 N/A 00 E V
cnfins Fn inst. of engine for mult engns (not mstr/rcvr)
j1939_ecu_instance 155A.5 0.0 N/A 0 E E
cneins ECM inst for currnt fn. (mstr=0, rcvr1=1,etc...)
j1939_time_segment2 155B 4.0 DEC 4 E V
jhits2 J1939: CAN interface timing register#2 initializtn
j1939_time_segment1 155B.4 9.0 DEC 9 E V
jhits1 J1939: CAN interface timing register#1 initializtn
governor_rating_11 155C 0.0 Flg 0 E B
ragv11 selects GOV RATING if sw1=on + sw2=on OR ratovr=3
governor_rating_10 155C.2 2.0 Flg 2 E B
ragv10 selects GOV RATING if sw1=on +sw2=off OR ratovr=2
governor_rating_01 155C.4 1.0 Flg 1 E B
ragv01 selects GOV RATING if sw1=off+ sw2=on OR ratovr=1
governor_rating_00 155C.6 0.0 Flg 0 E B
ragv00 selects GOV RATING if sw1=off+sw2=off OR ratovr=0
throttle_rating_00 155D 0.0 Flg 0 E B
ratp00 selects TPS RATING if sw1=off+sw2=off OR ratovr=0
mm_level_lamps_mode 155D.2 1.0 Flg 1 E V
mmlvlm mm SEL/CEL 0-none 1 ign on 2 CEL whl flt act 3-bth
mm_filter_lamps_mode 155D.4 2.0 Flg 2 E V
mmfllm mm SEL/CEL 0-none 1-ign on 2-CEL whl flt act 3-bth
j1939_sampling_jump_width 155D.6 1.0 Flg 1 E V
jhisjw J1939: sets the CAN timing registers
afrs_quantised 155E 1.0 Flg 1 E V
mmafqn if set, AFRS data reported on J1587 is quantized
adaptive_cc_equipped 155E.1 0.0 Flg 0 E D
acceq if set, vehicle has an adaptive cruise system
throttle_rating_11 155E.2 2.0 Flg 2 E B
ratp11 selects TPS RATING if sw1=on + sw2=on OR ratovr=3
throttle_rating_10 155E.4 2.0 Flg 2 E B
ratp10 selects TPS RATING if sw1=on +sw2=off OR ratovr=2
throttle_rating_01 155E.6 1.0 Flg 1 E B
ratp01 selects TPS RATING if sw1=off+ sw2=on OR ratovr=1
allow_pto_idle_shutdown 155F 0.0 Flg 0 E D
ptshut set to enable IDLE SHUTDOWN on PTO
allow_pto_cruise 155F.1 1.0 Flg 1 E D
ccpto set to enable CRUISE SWITCH PTO
allow_override_idle_shutdown 155F.2 0.0 Flg 0 E D
isovr set to enable IDLE SHUTDOWN OVERRIDE
allow_oilp_fault_override 155F.3 1.0 Flg 1 E E
aolpo set to allow low Oil Pressure Stop Eng Override
allow_idle_shutdown 155F.4 1.0 Flg 1 E D
isenb set to enable IDLE SHUTDOWN
allow_govgain_adjust 155F.5 0.0 Flg 0 E B
gvoadj if set, allow gvovga customer cal changes
allow_ccp_fault_override 155F.6 1.0 Flg 1 E E
accpo set to allow high CrkCasePress Stop Eng Override
air_comp_enable 155F.7 0.0 Flg 0 E E
pgsenb set to enable Air Compressor Pressure Gov Control
aux2_veps_config 1560 0.0 Flg 0 E V
ax2vcf set to enable VEPS config. of the aux_2 anlg chnl.
aux3_veps_config 1560.1 1.0 Flg 1 E V
ax3vcf set to enable VEPS config. of the aux_3 anlg chnl.
aux4_veps_config 1560.2 0.0 Flg 0 E V
ax4vcf set to enable VEPS config. of the aux_4 anlg chnl.
aux5_veps_config 1560.3 0.0 Flg 0 E V
ax5vcf set to enable VEPS config. of the aux_5 anlg chnl.
aux6_veps_config 1560.4 0.0 Flg 0 E V
ax6vcf set to enable VEPS config. of the aux_6 anlg chnl.
aux7_veps_config 1560.5 1.0 Flg 1 E V
ax7vcf set to enable VEPS config. of the aux_7 anlg chnl.
ati_error_enable 1560.6 0.0 Flg 0 E V
diauxi ATI: Set to enable Aux Timed In diagnostic
anti_theft_protection 1560.7 0.0 Flg 0 E V
atenab If set, anti-theft en. for no start, idle, opt idl
ce_off_fts_scaled_high 1561 1.0 Flg 1 E V
ftshce Set to disable CheckEngLt for fuel temp high fault
cc_auto_resume 1561.1 0.0 Flg 0 E D
ccauto CC: Enable auto resume feature
cc_atp_reset 1561.2 0.0 Flg 0 E B
ccatpr set for cc atp reset
boi_output_enable 1561.3 0.0 Flg 0 E E
boienb set to enable serial transmission of BOI data
baro_nox_1min_column_enable 1561.4 1.0 Flg 1 E V
bx1mce set, use the BX1MLC instead of bn1mnl
aux_temp_1_veps_config 1561.5 0.0 Flg 0 E V
at1vcf set to enbl VEPS cnfg of aux_temp_1 anlg chnl.
aux_temp_2_veps_config 1561.6 0.0 Flg 0 E V
at2vcf set to enbl VEPS cnfg of aux_temp_2 anlg chnl.
aux1_veps_config 1561.7 1.0 Flg 1 E V
ax1vcf set to enable VEPS config. of the aux_1 anlg chnl.
customer_cal_security_lockout 1562 0.0 Flg 0 E V
culock set to disable VEPS and DDR cal reprogramming
cruise_functions_enable 1562.1 1.0 Flg 1 E D
ccenb set to enable RPM, MPH, & PSI CRUISE CONTROL modes
coolant_level_quantised 1562.2 1.0 Flg 1 E V
jqucol CLS: Set to send 0/100% on J1587, else scaled val
clock_error_enable 1562.3 0.0 Flg 0 E V
diclck RTC: Set to enable Real Time Clock Diagnostics
coolant_level_disable 1562.4 0.0 Flg 0 E E
cldis CLS: set to disable coolant level diagnostics
common_rail_sc_protect 1562.5 0.0 Flg 0 E V
crscpt set to disable entire bank if inj on bank shorted
cls_veps_config 1562.6 0.0 Flg 0 E V
clsvcf set to enable VEPS config. of a CLS analog chnl.
cel_faults_excluded_per_snl 1562.7 0.0 Flg 0 E E
snlcfx if set, faults will turn CEL on as SNL logic/cals
disable_pto_shutdown 1563 0.0 Flg 0 E E
norduc Set to disable slow/shut/rampdown protectn on PTO
disable_overtemp_warning 1563.1 0.0 Flg 0 E V
nocel Set for no overtemp warn CEL:scldhi<oiltemp<disolt
disable_injectors_this_ecu 1563.2 0.0 Flg 0 E B
disinj if set, disables injectors; box used as an I/O box
disable_est_air_temp 1563.3 0.0 Flg 0 E V
deairt if set, use sensor value, if not, estimate air tem
disable_cold_signal_on_pwm_fan 1563.4 0.0 Flg 0 E B
dcsopf set, cold eng dout is disabled if PWM fan > thresh
disable_cold_signal_on_dig_fan 1563.5 0.0 Flg 0 E B
dcsodf set, cold eng dout is disabled if dig fan requestd
disable_cold_signal_above_idle 1563.6 1.0 Flg 1 E V
ceidle Set:en ce-sgnl only fr strt mde & norm mde+idle gv
data_hub_periodic_enable 1563.7 0.0 Flg 0 E V
dhenp Not used by software but still required by EDS
engine_over_speed_fault_enable 1564 0.0 Flg 0 E E
rpmfen if set, fault occurs if rpm high warning lamp on
engine_is_4stroke 1564.1 1.0 Flg 1 E V
eng4s Set for 4-Stroke Engines
enable_overtemp_protection 1564.2 1.0 Flg 1 E E
srmany Set for overtemp protect:TQ+PTO reduced f(dgC>lim)
dynamic_brake_enabled 1564.3 0.0 Flg 0 E D
dbenb Set to enable FanOut#1 when jakes hi for more brkg
dual_to_single_tq_and_tcrpm 1564.4 0.0 Flg 0 E V
dtstqr dual to single turbo trans req speed and tq cond
dtype_for_trs 1564.5 1.0 Flg 1 E V
dtptrs Set to enable Flip Flop for TRS (0 = test mode)
dtype_for_srs 1564.6 1.0 Flg 1 E V
dtpsrs Set to enable Flip Flop for SRS (0 = test mode)
dp_recal_enable 1564.7 0.0 Flg 0 E B
dprenb set, enable EGR Press Diff Sensor Compensation lgc
fire_truck_enable 1565 0.0 Flg 0 E E
ftpenb FireTrk Press Gov: Set to enable pressure gov mode
fei_enable 1565.1 1.0 Flg 1 E V
feienb if set, enables the fuel econ incentive feature
fan_off_link_enable 1565.2 0.0 Flg 0 E B
folen if set, fan deactvtd if airtmp AND cltmp < calbrtn
fan_off_adv_reentry 1565.3 0.0 Flg 0 E B
foadre if set, allow fan BOI advance re-entry
european_rating 1565.4 0.0 "" 0 E B
eurort european_rating
ess_eng_brake_shift_enable 1565.5 0.0 Flg 0 E D
essjse Set to allow engine brakes with ESS shift
epa_boi_output_enable 1565.6 1.0 Flg 1 E V
epaboi if set, respond to request for BOI from EPA DDR
engineering_enable 1565.7 0.0 Flg 0 E V
engbit Set to enable SLEWING and CAL-ON-THE-FLY
ignore_ss_tq_reduction 1566 0.0 Flg 0 E B
isstqr if set, steady state tq reduction is not used
idle_shutdn_auto_override 1566.1 0.0 Flg 0 E V
isdnao if set and ext temp cond, use auto shutdn override
idle_shut_ignore_eng_t 1566.2 0.0 Flg 0 E E
isiget If set, eng tmp for idle-shtdn is ignored
high_trs_int_thresh 1566.3 0.0 Flg 0 E V
htrsth Set for high TRS integral thresh for 6 tooth S60
halfeng_allow_ddr 1566.4 1.0 "" 1 E V
headdr if set, DDR can change heenb
fts_veps_config 1566.5 0.0 Flg 0 E V
ftsvcf set to enable VEPS config. of a FTS analog chnl.
force_dual_turbo_in_start 1566.6 0.0 Flg 0 E V
fdtis If set, force dual seq turbo when in start mode
force_dual_turbo_at_idle 1566.7 0.0 Flg 0 E V
fdtai If set, force dual turbo for Seq Turbo when idling
j1939_diag_enable 1567 0.0 Flg 0 E V
di1939 Set to enable J1939 diagnostics
j1922_transmission_enable 1567.1 1.0 Flg 1 E V
jlotrx J1922: Set to act on J1922 transmission messages
j1922_abs_enable 1567.2 1.0 Flg 1 E V
jloabx J1922: Set to act on J1922 brake system messages
j1587_periodic_enable 1567.3 1.0 Flg 1 E V
jloenp J1587: Set to enable broadcast of J1587 messages
irt_auto_recovery 1567.4 0.0 Flg 0 E V
irtarc set to filter IRTMAX into rise time during fault
injector_cal_security_lockout 1567.5 0.0 Flg 0 E V
ijlock Set to prohibit injector cal code changes
inj_cal_codes_rpm_adj_enable 1567.6 0.0 Flg 0 E V
irpmae Set to enable RPM compensation of inj cal codes
init_vsg_int_after_smoke 1567.7 0.0 Flg 0 E V
ivsgin if set, I=TQ-P-D-LeadLag exiting smoke tq limiting
marine_torque_limit_enable 1568 0.0 Flg 0 E B
tqtenb Set to allow Marine TORQUE limiting
marine_pto_startup_disable 1568.1 0.0 Flg 0 E E
mptosd qualification of pto required on ignition cycle
low_oil_pressure_error_enable 1568.2 1.0 Flg 1 E V
dilolp OPS: Set to enable low Oil Pressure Diagnostics
low_gear_limit_enable 1568.3 1.0 Flg 1 E V
trlenb Set to allow low gear TORQUE limiting
lock_by_comms 1568.4 0.0 Flg 0 E V
lckcom Set to allow J1922 msage lock of tooth_error_times
late_change_enable 1568.5 0.0 Flg 0 E D
esslce Enables/disables late change feature
jake_service_brake_enable 1568.6 0.0 Flg 0 E D
jbsben Set for JakeBrk(s) only if service brakes engaged
jake_cruise_enable 1568.7 0.0 Flg 0 E D
jbcenb Jake Brk: Set for JakeBrk(s) if MPH>Cruise Set Spd
nox_adapt_when_1min_ld 1569 1.0 Flg 1 E B
nxadp1 if set, 1 min. rolling ave. for ATP reset enabled
nox_adapt_when_steady 1569.1 0.0 Flg 0 E B
nxasdy Set for NXDBOI adv in steady-state operation (US)
noise_control_enable 1569.2 1.0 Flg 1 E B
nclenb Set to allow Noise Control RPM limiting
multi_slave 1569.3 0.0 Flg 0 E V
cslave 12/16V: Set if Slave ECM on a multi-block engine
multi_master 1569.4 0.0 Flg 0 E V
cmstr 12/16V: Set if Master ECM on a multi-block engine
multi_error_enable 1569.5 1.0 Flg 1 E V
dislv 12/16V: Set to enable Master/Slave Comm Diagnostic
mm_ign_off_ddec_comms 1569.6 0.0 Flg 0 E V
nocoms if set, DDEC uniq allwd wth all dvcs aftr ign off
maxboi_limits_boi_in_split 1569.7 0.0 Flg 0 E B
mxbois if set use min(SMXBOI,MAXBOI) to lim BOI, else nrm
ops_veps_config 156A 0.0 Flg 0 E V
opsvcf set to enable VEPS config. of a OPS analog chnl.
oil_press_zero_rpm_check 156A.1 1.0 Flg 1 E V
olpchk if set, ops in-range failure check at zero rpm
oil_level_quantised 156A.2 1.0 Flg 1 E V
mmolqn if set, oil lvl reported on J1587 is quantized
ofrs_quantised 156A.3 1.0 Flg 1 E V
mmofqn if set, oil lvl reported on J1587 is quantized
nvram_error_enable 156A.4 1.0 Flg 1 E V
dinvme NonVOL: Set for NonVolatile Memory Error Diagnostc
nox_decels_are_trans 156A.5 0.0 Flg 0 E B
nxdtrn Set to increase ATP during decels (Europe)
nox_adapt_when_trans 156A.6 0.0 Flg 0 E B
nxatrn Set for NXDBOI adv in transient operation (Europe)
nox_adapt_when_2min_ld 156A.7 1.0 Flg 1 E B
nxadp2 if set, 2 min. rolling ave. for ATP reset enabled
pid_109_mirror_20 156B 0.0 Flg 0 E V
pdm109 if set pid 20 is brdcst when pid 109 is brdcst
pid_100_mirror_19 156B.1 0.0 Flg 0 E V
pdm100 if set pid 19 is brdcst when pid 100 is brdcst
pid_94_mirror_18 156B.2 0.0 Flg 0 E V
pdm94 if set pid 18 is brdcst when pid 94 is brdcst
park_brake_weight_enable 156B.3 1.0 Flg 1 E V
pbwenb if set, wghted temp is used w lookup tbl BOI offse
overboost_tq_limit_enable 156B.4 0.0 Flg 0 E V
obtqle If set, overboost torque limit is enabled
ots_veps_config 156B.5 0.0 Flg 0 E V
otsvcf set to enable VEPS config. of a OTS analog chnl.
optimum_max_overload_at_wot 156B.6 0.0 Flg 0 E V
olcoaw if set, RTQ is usd to det opt load ovrld value
optimum_min_underload_at_zero 156B.7 0.0 Flg 0 E V
olcuaz if set, opt load underload tq cannot be < 0
rail_p_low_protect_disable 156C 0.0 Flg 0 E V
rplprd if set allows alt rail press sensor failure mode
pto_is_primary 156C.1 0.0 Flg 0 E E
ptmain Set for primary PTO operatn: rampdown+PTO @ pwr-on
pto_if_counts_zero 156C.2 1.0 Flg 1 E E
ptoffz Set for PTOS=idl & Clr for PTOS=PTMINV w/ counts=0
boi_ss_on_pto_enable 156C.3 1.0 Flg 1 E V
ssptoe if set, adv BOI to ss if anPTO|exengsync|cc press
progressive_shift_enable 156C.4 0.0 Flg 0 E D
pssenb set to enable PROGRESSIVE SHIFT
pto_veps_config 156C.5 0.0 Flg 0 E V
ptovcf set to enable VEPS config. of PTO analog chanl.
ps_enable 156C.6 1.0 Flg 1 E V
psenab if set, enable passing speed feature
pid_101_mirror_153 156C.7 1.0 Flg 1 E V
pdm101 if set pid 153 is brdcst when pid 101 is brdcst
shift_detect_enable 156D 1.0 Flg 1 E V
vrpshd VGR: Set for Virtual Gear Ratio shift detect logic
seo_toggle_enable 156D.1 0.0 Flg 0 E B
seotgl set to latch StpEngOvrd on hi-lo-hi switch transtn
schedule_from_earlier_tooth 156D.2 0.0 Flg 0 E V
sfetth if set, inj sched tooth interrupt 70 dg before TDC
road_speed_limit_enable 156D.3 1.0 Flg 1 E D
rslenb set to enable ROAD SPEED LIMITING
second_chance_enable 156D.4 0.0 Flg 0 E D
esssce Enables/disables the second chance feature
sa_use_trip_mileage 156D.5 0.0 Flg 0 E D
mpgust Set for TRIP Fuel Economy MPG/else use filterd MPG
risetime_error_enable 156D.6 1.0 Flg 1 E V
diirt IRT: Set for Inj Rise Time short & long Diagnostic
relative_boost_active 156D.7 1.0 Flg 1 E B
scgage if set SCTORQ pressure axis=abs boost-baro+100 kpa
slow_on_cylhead_temp 156E 0.0 Flg 0 E V
srmcht set to enable RAMP DOWN if CylHd Tmp Hi AND>discht
slow_on_crankcase_pressure 156E.1 0.0 Flg 0 E D
srmckp set to enable RAMP DOWN if Crankcase Pressure High
slow_on_coolant_temp 156E.2 1.0 Flg 1 E D
srmcot set to enable RAMP DOWN if Cool Tmp Hi AND >discot
slow_on_coolant_pressure 156E.3 0.0 Flg 0 E D
srmcop set to enable RAMP DOWN if Cool Prs Low
slow_on_coolant_level 156E.4 0.0 Flg 0 E D
srmcol set to enable RAMP DOWN if CLS Low AND < discol
skip_shift_enable 156E.5 0.0 Flg 0 E D
esssse Enables/disables the skip shift feature
boi_adv_max_offset_enable 156E.6 1.0 Flg 1 E V
boiofe if set pick largest BOI offset among allowed ones
shutdn_override_fullpower 156E.7 0.0 Flg 0 E E
seofp SEO: Set for full power on a Stop Engine Override
slow_on_stop2 156F 0.0 Flg 0 E D
srmin2 set to enable RAMP DOWN if Ext Stop Eng swtch2 low
slow_on_stop1 156F.1 1.0 Flg 1 E D
srmin1 set to enable RAMP DOWN if Ext Stop Eng swtch1 low
slow_on_rail_pressure 156F.2 0.0 Flg 0 E V
srmrlp set to enable RAMP DOWN if Rail Prs Hi
slow_on_oil_temp 156F.3 1.0 Flg 1 E D
srmolt set to enable RAMP DOWN if Oil Temp Hi AND >disolt
slow_on_oil_pressure 156F.4 1.0 Flg 1 E D
srmolp set to enable RAMP DOWN if Oil Pressure Low
slow_on_oil_level 156F.5 0.0 Flg 0 E D
srmoll set to enable RAMP DOWN if Oil Lvl Low AND <disoll
slow_on_inner_temp 156F.6 0.0 Flg 0 E D
srmict set to enable RAMP DOWN if InrClrTmp Hi AND>DISICT
slow_on_ex_temp 156F.7 1.0 Flg 1 E V
srmext set to enable RAMP DOWN if Exhst Tmp HI AND>disext
stop_on_cylhead_temp 1570 0.0 Flg 0 E V
stpcht set for SHUTDOWN if CylHdTmpHi AND>discht for seti
stop_on_crankcase_pressure 1570.1 0.0 Flg 0 E D
stpckp set for SHUTDOWN if Crankcase Press Hi for setimr
stop_on_coolant_temp 1570.2 1.0 Flg 1 E D
stpcot set for SHUTDOWN if CoolTmpHi AND>discot for setim
stop_on_coolant_pressure 1570.3 0.0 Flg 0 E D
stpcop set for SHUTDOWN if Cool Prs low
stop_on_coolant_level 1570.4 0.0 Flg 0 E D
stpcol set for SHUTDOWN if CLS Low AND<discol for setimr
srs_error_allowed 1570.5 1.0 Flg 1 E V
difsrs SRS: Set to enable SRS/TRS Diagnostics
slow_on_transmission_temp 1570.6 0.0 Flg 0 E V
srmtrt set to enable RAMP DOWN if Trans Tmp Hi AND>distrt
slow_on_tco_temp 1570.7 0.0 Flg 0 E V
srmtct set to enable ramp down if tco temp is over limit
stop_on_stop2 1571 0.0 Flg 0 E D
stpin2 set for SHUTDOWN if Ext Stp Eng SW2 low for setimr
stop_on_stop1 1571.1 1.0 Flg 1 E D
stpin1 set for SHUTDOWN if Ext Stp Eng SW1 low for setimr
stop_on_rail_pressure 1571.2 0.0 Flg 0 E V
stprlp set for SHUTDOWN if Rail Prs High for setimr
stop_on_oil_temp 1571.3 1.0 Flg 1 E D
stpolt set for SHUTDOWN if OilTempHi AND>disolt for setim
stop_on_oil_pressure 1571.4 1.0 Flg 1 E D
stpolp set for SHUTDOWN if Oil Pressure Low for setimr
stop_on_oil_level 1571.5 0.0 Flg 0 E D
stpoll set for SHUTDOWN if OilLvl Lo AND<disoll for setim
stop_on_inner_temp 1571.6 0.0 Flg 0 E D
stpict set for SHUTDOWN if InrClrTmpHi AND>DISICT for tmr
stop_on_ex_temp 1571.7 1.0 Flg 1 E V
stpext set for SHUTDOWN if ExhstTmpHi AND>disext for seti
turbo_speed_on_receiver 1572 0.0 Flg 0 E V
tsor Receiver ECM turbo speed sensor diagnostic enable
turbo_overspd_tq_limit_enable 1572.1 0.0 Flg 0 E B
tboste set to enable turbo overspeed torque limiting
tps_veps_config 1572.2 0.0 Flg 0 E V
tpsvcf set to enable VEPS config. of a TPS analog chnl.
tbs_veps_config 1572.3 0.0 Flg 0 E V
tbsvcf set to enable VEPS config. of a TPS analog chnl.
tas_enable 1572.4 0.0 Flg 0 E E
tasenb set to enable Optimized Idle auto-start/stop
t2_cruise_sw_config 1572.5 0.0 Flg 0 E V
astcsc if set, enables top2 using cruise master switch
stop_on_transmission_temp 1572.6 0.0 Flg 0 E V
stptrt set for SHUTDOWN if TransTmpHi AND>distrt for seti
stop_on_tco_temp 1572.7 0.0 Flg 0 E V
stptct set for SHUTDOWN if tco temp is over the limit
vss_is_turbo_speed 1573 0.0 Flg 0 E B
vssits set to measure turbo speed on vss port
vss_is_etc1_msg 1573.1 0.0 Flg 0 E D
vssmsg Set to obtain VehSpd from J1939 trans & ignore VSS
use_mean_rpm 1573.2 0.0 Flg 0 E V
useave Set to use D2 TRS periods for inj pulse scheduling
twins_median_filter 1573.3 1.0 Flg 1 E V
tsmdfi set to enable impulse filter on ext sync spd input
twins_exit_disable_pto 1573.4 0.0 Flg 0 E E
tsdpto set to force PTO requal on sync to PTO transition
twin_sync_enable 1573.5 0.0 Flg 0 E E
twins SYNC: Set for twin engine RPM synchronization
twin_marine_entry_exit 1573.6 0.0 Flg 0 E E
tmaree set if marine ERIM used for loss of sync speed
turbo_torque_source 1573.7 0.0 Flg 0 E V
tbtsrc Turbo/Blower Bypass Torque source: 0=FTQ else=RTQI
patch_1 1574 0.0 Flg 0 E V
pitst1 Set to enable Test Software
use_hall_effect 1574.1 0.0 Flg 0 E V
usehal set for S30G Hall Effect SRS/TRS sensor
warn_only_overrides_otp 1574.2 0.0 Flg 0 E V
woootp set to disable ovr temp protection-make warn only
vss_tamp_enable 1574.3 0.0 Flg 0 E B
vstmpe Set to enable VSS anti-tampering logic
vss_sensor_enable 1574.4 1.0 Flg 1 E D
vssenb VSS: Set to enable VEHICLE SPEED SENSOR
vss_nox_adapt_enable 1574.5 1.0 Flg 1 E V
vnxenb enb ability to advance timing based on VSS
vss_magnetic_sensor 1574.6 1.0 Flg 1 E D
vssmag VSS: VSS sensor type is magnetic (vs. open coll)
vss_is_wheel_sensor 1574.7 0.0 Flg 0 E D
vsswhl VSS: VSS sensor type is wheel (vs. trans output)
patch_9 1575 0.0 Flg 0 E V
ptch9 patch_9
patch_8 1575.1 0.0 Flg 0 E V
pitst8 Set to enable Test Software
patch_7 1575.2 0.0 Flg 0 E V
pitst7 Set to enable Test Software
patch_6 1575.3 0.0 Flg 0 E V
pitst6 Set to enable Test Software
patch_5 1575.4 0.0 Flg 0 E V
pitst5 Set to enable Test Software
patch_4 1575.5 0.0 Flg 0 E V
pitst4 Set to enable Test Software
patch_3 1575.6 0.0 Flg 0 E V
pitst3 Set to enable Test Software
patch_2 1575.7 0.0 Flg 0 E V
pitst2 Set to enable Test Software
patch_16 1576.1 0.0 Flg 0 E V
ptch16 patch_16
patch_15 1576.2 0.0 Flg 0 E V
ptch15 patch_15
patch_14 1576.3 0.0 Flg 0 E V
ptch14 patch_14
patch_13 1576.4 0.0 Flg 0 E V
ptch13 patch_13
patch_12 1576.5 0.0 Flg 0 E V
ptch12 patch_12
patch_11 1576.6 0.0 Flg 0 E V
ptch11 patch_11
patch_10 1576.7 0.0 Flg 0 E V
ptch10 patch_10

NAME: fuel_t_inj_correction ADDR: 1578 UNT: "" OWN: V CODE: ftincr


EQN: E
injector turnoff delay as a f(fuel temp)
dgC| HEX| ""
--------------------------------
-40.0| 0000| 0.0
-27.8| 0000| 0.0
-15.6| 0000| 0.0
-3.3| 0000| 0.0
8.9| 0000| 0.0
21.1| 0000| 0.0
33.3| 0000| 0.0
45.6| 0000| 0.0
57.8| 0000| 0.0
70.0| 0000| 0.0
82.2| 0000| 0.0
94.4| 0000| 0.0
106.7| 0000| 0.0
118.9| 0000| 0.0
131.1| 0000| 0.0
143.3| 0000| 0.0
155.6| 0000| 0.0

NAME: pulse_width_table ADDR: 159A UNT: "" OWN: B CODE: provpw


EQN: E*256
PulseWidth Tbl-f(RPM,TQ):-64 to +64deg w/ .004 res

Table of AXIS_%_Torque_9
%_Torque ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 5.5430 8.2109 10.4805 14.8164 18.9883 23.0781
26.4297 29.6484 33.1367
X 300.0 | 4.3828 7.2500 9.9844 13.9570 17.9141 21.7461
25.1797 28.5508 32.1055
I 450.0 | 3.4102 6.4531 9.5664 13.2695 17.0938 20.7422
24.2539 27.7500 31.3711
S 600.0 | 2.6250 5.8398 9.2305 12.7734 16.4922 20.0469
23.6133 27.2422 30.9258
_ 750.0 | 2.0195 5.2734 8.9180 12.3633 16.2461 19.7695
23.4063 27.1016 30.8555
R 900.0 | 1.6172 5.1094 8.9141 12.2539 16.1211 19.7695
23.4531 27.1328 30.9414
P 1050.0 | 1.3633 4.8672 8.5586 12.2539 16.2383 19.9414
23.6328 27.5898 31.4727
M 1200.0 | 1.3320 4.9102 8.6953 12.3867 16.7461 20.7383
24.4805 28.2930 32.2305
_ 1350.0 | 0.0547 3.8398 8.2969 12.5039 16.6367 20.7266
24.6758 28.8438 33.5039
1 1500.0 | -0.6797 3.6563 8.5117 12.6016 17.0469 21.2031
25.5430 30.0078 34.8633
7 1650.0 | -1.0000 3.0000 8.0156 12.1680 16.9375 21.7500
26.6289 31.7148 37.1641
1800.0 | -1.0000 2.5156 7.2031 12.1094 17.1211 22.1680
27.7188 32.9375 38.9805
1950.0 | -1.0000 2.2266 6.7773 12.0430 17.3047 23.0156
29.1016 34.6680 40.0000
2100.0 | -1.0000 2.3281 6.6680 11.8984 17.6797 23.9063
30.8555 37.1211 40.0000
2250.0 | -0.8086 2.5703 6.5391 11.9883 18.1953 24.9688
32.7070 39.4453 39.4336
2400.0 | -0.5508 3.0820 6.6250 12.1211 18.8477 26.1953
34.8320 40.0000 38.0469
2550.0 | -0.2031 3.8359 6.8789 12.3320 19.6406 27.5781
37.1836 40.0000 35.8867

Table of Hex Values


%_Torque ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 058b 0836 0a7b 0ed1 12fd 1714
1a6e 1da6 2123
X 300.0 | 0462 0740 09fc 0df5 11ea 15bf
192e 1c8d 201b
I 450.0 | 0369 0674 0991 0d45 1118 14be
1841 1bc0 1f5f
S 600.0 | 02a0 05d7 093b 0cc6 107e 140c
179d 1b3e 1eed
_ 750.0 | 0205 0546 08eb 0c5d 103f 13c5
1768 1b1a 1edb
R 900.0 | 019e 051c 08ea 0c41 101f 13c5
1774 1b22 1ef1
P 1050.0 | 015d 04de 088f 0c41 103d 13f1
17a2 1b97 1f79
M 1200.0 | 0155 04e9 08b2 0c63 10bf 14bd
187b 1c4b 203b
_ 1350.0 | 000e 03d7 084c 0c81 10a3 14ba
18ad 1cd8 2181
1 1500.0 | ffffff52 03a8 0883 0c9a 110c 1534
198b 1e02 22dd
7 1650.0 | ffffff00 0300 0804 0c2b 10f0 15c0
1aa1 1fb7 252a
1800.0 | ffffff00 0284 0734 0c1c 111f 162b
1bb8 20f0 26fb
1950.0 | ffffff00 023a 06c7 0c0b 114e 1704
1d1a 22ab 2800
2100.0 | ffffff00 0254 06ab 0be6 11ae 17e8
1edb 251f 2800
2250.0 | ffffff31 0292 068a 0bfd 1232 18f8
20b5 2772 276f
2400.0 | ffffff73 0315 06a0 0c1f 12d9 1a32
22d5 2800 260c
2550.0 | ffffffcc 03d6 06e1 0c55 13a4 1b94
252f 2800 23e3

NAME: pulse_width_split_main_table ADDR: 16CC UNT: "" OWN: B CODE:


prvmpw EQN: E*256
Split PPW TBL -f(RPM,TQ): -1 to +64 deg w/.004 res

Table of AXIS_%_Torque_9
%_Torque ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 4.7266 7.8750 10.1563 12.9961 22.0430 26.7578
32.1797 35.0000 35.0000
X 300.0 | 3.9219 7.1914 9.8516 13.0117 20.4141 25.0664
29.8125 34.6563 35.0000
I 450.0 | 3.1719 6.5586 9.5898 13.0391 19.1289 23.7109
27.9531 32.4609 35.0000
S 600.0 | 2.4258 6.0117 9.3359 13.0586 18.1953 22.6328
26.6641 30.8867 35.0000
_ 750.0 | 1.9141 5.4180 9.3008 13.1953 17.5898 22.1680
25.5391 29.6055 33.7422
R 900.0 | 1.1875 5.0234 9.0156 13.1953 17.3164 21.6250
25.6328 29.5859 33.7148
P 1050.0 | 0.6016 4.6484 8.9609 13.2734 17.4727 21.6094
25.4609 29.2305 33.9805
M 1200.0 | 0.1953 4.2383 8.9648 13.4180 17.8594 22.0664
26.2344 30.1211 34.4336
_ 1350.0 | 1.0938 3.9023 8.5508 13.6406 18.0117 22.5391
27.0469 31.6055 35.0000
1 1500.0 | -0.2109 3.3281 7.9844 13.2695 17.6602 22.4297
27.4609 33.3984 35.0000
7 1650.0 | -1.0000 2.6914 7.3672 13.3320 18.8555 24.1328
30.2617 33.2539 35.0000
1800.0 | -1.0000 1.8672 7.2305 13.3555 19.1172 24.8711
30.2070 35.0000 35.0000
1950.0 | -1.0000 3.0234 7.0078 13.5664 19.3789 25.0430
29.7305 35.0000 35.0000
2100.0 | 0.6797 2.8555 6.5977 13.6094 19.4688 24.5352
28.6055 34.5508 35.0000
2250.0 | 2.4961 4.0273 6.4609 13.7773 19.0313 23.2422
25.6406 34.2773 35.0000
2400.0 | 5.1445 5.4219 6.3125 13.9414 18.3359 21.2617
21.6797 33.5000 35.0000
2550.0 | 8.4961 7.2383 6.2109 14.1328 17.3281 18.5664
16.5352 32.3906 35.0000

Table of Hex Values


%_Torque ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 04ba 07e0 0a28 0cff 160b 1ac2
202e 2300 2300
X 300.0 | 03ec 0731 09da 0d03 146a 1911
1dd0 22a8 2300
I 450.0 | 032c 068f 0997 0d0a 1321 17b6
1bf4 2076 2300
S 600.0 | 026d 0603 0956 0d0f 1232 16a2
1aaa 1ee3 2300
_ 750.0 | 01ea 056b 094d 0d32 1197 162b
198a 1d9b 21be
R 900.0 | 0130 0506 0904 0d32 1151 15a0
19a2 1d96 21b7
P 1050.0 | 009a 04a6 08f6 0d46 1179 159c
1976 1d3b 21fb
M 1200.0 | 0032 043d 08f7 0d6b 11dc 1611
1a3c 1e1f 226f
_ 1350.0 | 0118 03e7 088d 0da4 1203 168a
1b0c 1f9b 2300
1 1500.0 | ffffffca 0354 07fc 0d45 11a9 166e
1b76 2166 2300
7 1650.0 | ffffff00 02b1 075e 0d55 12db 1822
1e43 2141 2300
1800.0 | ffffff00 01de 073b 0d5b 131e 18df
1e35 2300 2300
1950.0 | ffffff00 0306 0702 0d91 1361 190b
1dbb 2300 2300
2100.0 | 00ae 02db 0699 0d9c 1378 1889
1c9b 228d 2300
2250.0 | 027f 0407 0676 0dc7 1308 173e
19a4 2247 2300
2400.0 | 0525 056c 0650 0df1 1256 1543
15ae 2180 2300
2550.0 | 087f 073d 0636 0e22 1154 1291
1089 2064 2300

NAME: rail_p_inj_irt_to_boi_delay ADDR: 17FE UNT: "" OWN: V CODE:


rpirad EQN: E
if rpinen is set, BOE = BOI+rpirad
Volts| HEX| ""
--------------------------------
0.0| 0000| 0.0
3.2| 0000| 0.0
6.4| 0000| 0.0
9.6| 0000| 0.0
12.8| 0000| 0.0
16.0| 0000| 0.0
19.2| 0000| 0.0
22.4| 0000| 0.0
25.6| 0000| 0.0
28.8| 0000| 0.0
32.0| 0000| 0.0
35.2| 0000| 0.0
38.4| 0000| 0.0
41.6| 0000| 0.0
44.8| 0000| 0.0
48.0| 0000| 0.0
51.2| 0000| 0.0

NAME: split_pilot_torque ADDR: 1820 UNT: "" OWN: B CODE: plttq


EQN: E*20.47
SPLIT INJ Pilot Pulse TQ as a f(RPM)
RPM| HEX| ""
--------------------------------
150.0| 0085| 6.497
300.0| 0088| 6.644
450.0| 008e| 6.937
600.0| 0095| 7.279
750.0| 009c| 7.621
900.0| 00a4| 8.012
1050.0| 00a4| 8.012
1200.0| 00a4| 8.012
1350.0| 00a4| 8.012
1500.0| 00a4| 8.012
1650.0| 00a4| 8.012
1800.0| 00a4| 8.012
1950.0| 00a4| 8.012
2100.0| 00a4| 8.012
2250.0| 00a4| 8.012
2400.0| 00a4| 8.012
2550.0| 00a4| 8.012
NAME: split_max_torque ADDR: 1842 UNT: "" OWN: V CODE: epmxtq
EQN: E*20.47
For SPLIT INJ %FTQ < EPMXTQ
RPM| HEX| ""
--------------------------------
150.0| 07ff| 100.000
300.0| 07ff| 100.000
450.0| 07ff| 100.000
600.0| 07ff| 100.000
750.0| 07ff| 100.000
900.0| 07ff| 100.000
1050.0| 07ff| 100.000
1200.0| 07ff| 100.000
1350.0| 07ff| 100.000
1500.0| 07ff| 100.000
1650.0| 07ff| 100.000
1800.0| 07ff| 100.000
1950.0| 07ff| 100.000
2100.0| 07ff| 100.000
2250.0| 07ff| 100.000
2400.0| 07ff| 100.000
2550.0| 07ff| 100.000

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
acb_adjust_maxpw 1864 8.0000 DEG 0800 E*256 V
acbapw Final PW < acbapw for Adaptive Cylinder Balance
acb_adjust_maxrpm 1866 1000.00 RPM 0fa0 E*4 V
acbarp ACB disabld @ RPM>acbarp+50 & reenabld RPM<acbarp
acb_adjust_maxtemp 1868 -7.01 dgC 01db (E+40)*14.4 V
acblot oil temp > acblot for ACB to recalc PW adjustment
acb_end_angle 186A 140.00 DEG 0230 E*4 V
acbend ACB: Crk degs after TDC for start of RPM sample
acb_learn_gain 186C 0.003098 P/R 00cb E*65536 V
acbgn ACB gain in PW per cylinder delta RPM
acb_learn_maxrpm 186E 900.00 RPM 0e10 E*4 V
acblrp RPM < acblrp for ACB to recalculate PW adjustment
acb_maxadjust 1870 1.0000 DEG 0100 E*256 V
acblim Adaptive Cylinder Balance +/- PW adjustment limit
acb_start_angle 1872 120.00 DEG 01e0 E*4 V
acbst ACB: Crk degs after TDC for end of RPM sample
air_temp_fan_off_adv 1874 57.78 dgC 0580 (E+40)*14.4 B
atadvf Airtmp<ctadvf which boi advance will be set to 0
air_temp_fan_on_adv 1876 68.82 dgC 061f (E+40)*14.4 B
atadvn Airtmp>atadvn where boi may be adv to max boi
cool_temp_fan_off_adv 1878 95.00 dgC 0798 (E+40)*14.4 B
ctadvf Cooltmp<ctadvf which boi advance will be set to 0
cool_temp_fan_on_adv 187A 100.63 dgC 07e9 (E+40)*14.4 B
ctadvn Cooltmp>ctadvn where boi may be adv to max boi
default_rcvr_rail_press 187C 1200.0 BAR 04b0 E V
drcrp Default rail pressure on receiver if J1939 fails
fuel_usage_constant 187E 0.000047565 GPH/ 063c E*33554432
V fconst fuel cons calc: converts mm^3/injection to GPH/RPM
halfeng_fuel_factor 1880 0.5000 MLT 0080 E*256 V
hefufc 1/2 engine mode fuel consumption multiplier
halfeng_max_delta_temp 1882 -40.00 dgC 0000 (E+40)*14.4 V
hemxdt 1/2EngTemp ever>HEMXDT then HEMTQD always disabled
halfeng_max_oilt 1884 12.50 dgC 02f4 (E+40)*14.4 V
hemaxt 1/2EngTemp>HEMAXT then half engine mode disabled
halfeng_temp_weighting_pid0 1886 175.0 PID 00af E V
hepd0 temp PID multiplied by (1-HEFAC) for HalfEng Temp
halfeng_temp_weighting_pid1 1888 172.0 PID 00ac E V
hepd1 temp PID multiplied by HEFAC for HalfEng Temp
hp_pump_ff_gain 188A 0.250 U/T= 0032 E*200 V
hppffg %pump utilization = prop + integral + feedforward
hp_pump_i_gain 188C 0.00107 U/P/ 0007 E*6554 V
hppig integral=intergral+HPPIG*PressError
hp_pump_max_dc_constant 188E 650.0 D*V= 028a E V
hpmxdc high press pump PWM %DC = (utilization * . . .
hp_pump_min_dc_constant 1890 100.0 D*V= 0064 E V
hpmndc . . . (HPMXDC - HPMNDC) + HPMNDC) / Vbattery
hp_pump_p_gain 1892 0.0050011 U/P= 051f E*262144 V
hpppg prop=HPPPG*PressError feedfrwd=HPPFFG*FTQ
min_firing_rail_p 1894 150.03 BAR 0880 E*14.504 V
rlprmn rail press > RLPRMN before firing inj during crank
rail_p_lo_min_rpm 1896 450.00 RPM 0708 E*4 V
rlmnsp RPM>RLMNSP for rail press low fault
size_fudge_factor 1898 1.5000 MLT 0600 E*1024 V
fpcmul Fuel rate scaler (1=max fuel/firing is 255 mm3)
split_gap_time 189A 1200.0 uSC 04b0 E V
epigmn time end pilot pulse to start main pulse > epigmn
split_max_rpm 189C 1350.00 RPM 1518 E*4 V
epirpm RPM < epirpm for Split Injection
split_max_weighted_temp 189E 244.38 dgC 0fff (E+40)*14.4 V
epimxt max temp for split injection to be enabled
split_min_torque 18A0 2.980 %TQ 003d E*20.47 V
epimtq %TQ>epimtq*ztqscl for SPLIT INJECTION
split_rpm_hyst 18A2 50.00 RPM 00c8 E*4 V
epirhy SPLIT INJECTION RPM hysteresis
split_smoke_cntl_tq_adder 18A4 14.949 %TQ 0132 E*20.47 V
episct ATQ=ATQ+EPISCT if SPLIT INJ AND out of START mode
split_temp_weighting_pid0 18A6 175.0 PID 00af E V
epipd0 PID for 1st tmp snsr for split inj enbl temp limit
split_temp_weighting_pid1 18A8 172.0 PID 00ac E V
epipd1 PID for 2nd tmp snsr for split inj enbl temp limit
split_torque_hyst 18AA 0.977 %TQ 0014 E*20.47 V
epimth Tq must exceed epmxtq+epimth to exit EPI

NAME: desired_rail_p ADDR: 18AC UNT: "" OWN: B CODE: rlpres


EQN: E/9.375
S4000 desired rail pressure as f(RPM,TQ)

Table of AXIS_%_Torque_9
%_Torque ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
X 300.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
I 450.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
S 600.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 750.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
R 900.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
P 1050.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
M 1200.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 1350.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1 1500.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
7 1650.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1800.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1950.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2100.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2250.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2400.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2550.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0

Table of Hex Values


%_Torque ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 00 00 00 00 00
00 00 00
X 300.0 | 00 00 00 00 00 00
00 00 00
I 450.0 | 00 00 00 00 00 00
00 00 00
S 600.0 | 00 00 00 00 00 00
00 00 00
_ 750.0 | 00 00 00 00 00 00
00 00 00
R 900.0 | 00 00 00 00 00 00
00 00 00
P 1050.0 | 00 00 00 00 00 00
00 00 00
M 1200.0 | 00 00 00 00 00 00
00 00 00
_ 1350.0 | 00 00 00 00 00 00
00 00 00
1 1500.0 | 00 00 00 00 00 00
00 00 00
7 1650.0 | 00 00 00 00 00 00
00 00 00
1800.0 | 00 00 00 00 00 00
00 00 00
1950.0 | 00 00 00 00 00 00
00 00 00
2100.0 | 00 00 00 00 00 00
00 00 00
2250.0 | 00 00 00 00 00 00
00 00 00
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: desired_rail_pressure_max ADDR: 1945 UNT: "" OWN: B CODE: rlprsx


EQN: E/9.375
S4000 max desired rail pressure as f(RPM,TQ)

Table of AXIS_%_Torque_9
%_Torque ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
X 300.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
I 450.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
S 600.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 750.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
R 900.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
P 1050.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
M 1200.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 1350.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1 1500.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
7 1650.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1800.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1950.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2100.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2250.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2400.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
2550.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0

Table of Hex Values


%_Torque ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 00 00 00 00 00
00 00 00
X 300.0 | 00 00 00 00 00 00
00 00 00
I 450.0 | 00 00 00 00 00 00
00 00 00
S 600.0 | 00 00 00 00 00 00
00 00 00
_ 750.0 | 00 00 00 00 00 00
00 00 00
R 900.0 | 00 00 00 00 00 00
00 00 00
P 1050.0 | 00 00 00 00 00 00
00 00 00
M 1200.0 | 00 00 00 00 00 00
00 00 00
_ 1350.0 | 00 00 00 00 00 00
00 00 00
1 1500.0 | 00 00 00 00 00 00
00 00 00
7 1650.0 | 00 00 00 00 00 00
00 00 00
1800.0 | 00 00 00 00 00 00
00 00 00
1950.0 | 00 00 00 00 00 00
00 00 00
2100.0 | 00 00 00 00 00 00
00 00 00
2250.0 | 00 00 00 00 00 00
00 00 00
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: fuel_boi_correction ADDR: 19DE UNT: "" OWN: B CODE: fuboi


EQN: E*128
Fuel Cnsmptn Comp. Table for Cam Effects f(PW,BOI)

Table of AXIS_Pulse_width_17
Pulse_width ->
-1.0 1.5 4.0 6.5 9.0 11.5
14.0 16.5 19.0 21.5 24.0 26.5 29.0 31.5
34.0 36.5 39.0
-----------------------------------------------------------------------------------
-----------------------------------------------------------------------------------
---------------------------------------
A 0.0 | 0.938 1.109 1.078 1.078 1.078 1.063
1.063 1.063 1.047 1.047 1.055 1.047 1.039 1.031
1.031 1.031 1.031
X 2.0 | 0.938 1.094 1.070 1.070 1.070 1.047
1.055 1.055 1.039 1.039 1.039 1.039 1.031 1.031
1.031 1.031 1.031
I 4.0 | 0.938 1.047 1.063 1.063 1.063 1.047
1.047 1.047 1.031 1.031 1.031 1.031 1.023 1.023
1.023 1.023 1.023
S 6.0 | 0.953 1.031 1.039 1.055 1.039 1.016
1.023 1.031 1.016 1.031 1.016 1.016 1.016 1.016
1.008 1.008 1.008
_ 8.0 | 0.984 1.008 1.016 1.023 1.023 1.023
1.016 1.016 1.008 1.016 1.008 1.008 1.008 1.008
1.008 1.008 1.008
B 10.0 | 1.000 1.000 1.000 1.000 1.000 1.000
1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000
1.000 1.000 1.000
O 12.0 | 0.961 0.984 0.977 0.977 0.984 0.992
0.984 0.984 0.992 0.992 0.992 0.992 0.992 0.992
0.992 0.992 0.992
I 14.0 | 0.938 0.969 0.969 0.969 0.969 0.984
0.969 0.969 0.977 0.977 0.977 0.984 0.977 0.984
0.984 0.977 0.977
_ 16.0 | 0.883 0.953 0.953 0.953 0.953 0.969
0.961 0.961 0.953 0.961 0.969 0.969 0.969 0.969
0.969 0.969 0.969
1 18.0 | 0.797 0.836 0.875 0.930 0.930 0.938
0.930 0.930 0.930 0.945 0.938 0.945 0.945 0.953
0.953 0.953 0.953
7 20.0 | 0.672 0.758 0.813 0.859 0.883 0.930
0.930 0.930 0.930 0.930 0.930 0.930 0.930 0.930
0.930 0.930 0.930
22.0 | 0.672 0.719 0.766 0.813 0.867 0.906
0.906 0.898 0.898 0.898 0.898 0.898 0.898 0.898
0.898 0.898 0.898
24.0 | 0.672 0.695 0.727 0.813 0.891 0.906
0.898 0.898 0.898 0.898 0.898 0.898 0.898 0.898
0.898 0.898 0.898
26.0 | 0.672 0.688 0.758 0.852 0.898 0.906
0.898 0.898 0.891 0.898 0.898 0.898 0.898 0.898
0.898 0.898 0.898
28.0 | 0.672 0.727 0.813 0.875 0.898 0.906
0.898 0.891 0.891 0.898 0.898 0.898 0.898 0.898
0.898 0.898 0.898
30.0 | 0.734 0.789 0.852 0.891 0.898 0.898
0.898 0.891 0.891 0.898 0.898 0.898 0.898 0.898
0.898 0.898 0.898
32.0 | 0.781 0.828 0.867 0.891 0.891 0.898
0.898 0.891 0.891 0.898 0.898 0.898 0.898 0.898
0.898 0.898 0.898

Table of Hex Values


Pulse_width ->
-1.0 1.5 4.0 6.5 9.0 11.5
14.0 16.5 19.0 21.5 24.0 26.5 29.0 31.5
34.0 36.5 39.0
-----------------------------------------------------------------------------------
-----------------------------------------------------------------------------------
---------------------------------------
A 0.0 | 78 8e 8a 8a 8a 88
88 88 86 86 87 86 85 84
84 84 84
X 2.0 | 78 8c 89 89 89 86
87 87 85 85 85 85 84 84
84 84 84
I 4.0 | 78 86 88 88 88 86
86 86 84 84 84 84 83 83
83 83 83
S 6.0 | 7a 84 85 87 85 82
83 84 82 84 82 82 82 82
81 81 81
_ 8.0 | 7e 81 82 83 83 83
82 82 81 82 81 81 81 81
81 81 81
B 10.0 | 80 80 80 80 80 80
80 80 80 80 80 80 80 80
80 80 80
O 12.0 | 7b 7e 7d 7d 7e 7f
7e 7e 7f 7f 7f 7f 7f 7f
7f 7f 7f
I 14.0 | 78 7c 7c 7c 7c 7e
7c 7c 7d 7d 7d 7e 7d 7e
7e 7d 7d
_ 16.0 | 71 7a 7a 7a 7a 7c
7b 7b 7a 7b 7c 7c 7c 7c
7c 7c 7c
1 18.0 | 66 6b 70 77 77 78
77 77 77 79 78 79 79 7a
7a 7a 7a
7 20.0 | 56 61 68 6e 71 77
77 77 77 77 77 77 77 77
77 77 77
22.0 | 56 5c 62 68 6f 74
74 73 73 73 73 73 73 73
73 73 73
24.0 | 56 59 5d 68 72 74
73 73 73 73 73 73 73 73
73 73 73
26.0 | 56 58 61 6d 73 74
73 73 72 73 73 73 73 73
73 73 73
28.0 | 56 5d 68 70 73 74
73 72 72 73 73 73 73 73
73 73 73
30.0 | 5e 65 6d 72 73 73
73 72 72 73 73 73 73 73
73 73 73
32.0 | 64 6a 6f 72 72 73
73 72 72 73 73 73 73 73
73 73 73

NAME: fuel_per_firing ADDR: 1AFF UNT: "" OWN: B CODE: fumain


EQN: E/DC
Fuel Cnsmptn Table in mm^3/stroke f(PW,RPM)

Table of AXIS_Pulse_width_17
Pulse_width ->
-1.0 1.5 4.0 6.5 9.0 11.5
14.0 16.5 19.0 21.5 24.0 26.5 29.0 31.5
34.0 36.5 39.0
-----------------------------------------------------------------------------------
-----------------------------------------------------------------------------------
---------------------------------------
A 150.0 | 0.0 0.0 18.0 49.5 82.5 115.5
148.5 172.5 199.5 232.5 264.0 297.0 328.5 355.5
364.5 375.0 382.5
X 300.0 | 0.0 0.0 16.5 48.0 79.5 112.5
144.0 166.5 193.5 225.0 256.5 288.0 319.5 352.5
361.5 372.0 382.5
I 450.0 | 0.0 0.0 16.5 46.5 76.5 108.0
139.5 163.5 189.0 217.5 247.5 279.0 310.5 340.5
360.0 372.0 382.5
S 600.0 | 0.0 0.0 12.0 42.0 73.5 102.0
132.0 157.5 183.0 211.5 241.5 271.5 301.5 331.5
360.0 370.5 382.5
_ 750.0 | 0.0 1.5 15.0 42.0 70.5 102.0
132.0 156.0 183.0 208.5 235.5 264.0 294.0 324.0
352.5 370.5 382.5
R 900.0 | 0.0 3.0 22.5 49.5 72.0 97.5
124.5 151.5 177.0 205.5 232.5 256.5 286.5 315.0
343.5 364.5 378.0
P 1050.0 | 0.0 1.5 28.5 52.5 75.0 96.0
120.0 147.0 175.5 199.5 223.5 253.5 279.0 306.0
334.5 360.0 378.0
M 1200.0 | 0.0 3.0 30.0 49.5 67.5 90.0
111.0 136.5 163.5 189.0 214.5 244.5 274.5 301.5
328.5 351.0 375.0
_ 1350.0 | 0.0 4.5 31.5 52.5 69.0 85.5
112.5 138.0 163.5 184.5 211.5 238.5 265.5 294.0
316.5 342.0 370.5
1 1500.0 | 0.0 4.5 33.0 51.0 67.5 91.5
114.0 139.5 163.5 184.5 207.0 234.0 258.0 283.5
310.5 337.5 363.0
7 1650.0 | 0.0 15.0 36.0 54.0 70.5 93.0
115.5 139.5 165.0 186.0 205.5 229.5 256.5 280.5
304.5 328.5 360.0
1800.0 | 0.0 19.5 42.0 57.0 72.0 94.5
117.0 141.0 165.0 186.0 205.5 228.0 249.0 271.5
297.0 321.0 355.5
1950.0 | 1.5 24.0 45.0 58.5 75.0 97.5
118.5 141.0 166.5 186.0 205.5 226.5 246.0 268.5
289.5 321.0 349.5
2100.0 | 12.0 28.5 46.5 64.5 79.5 100.5
120.0 141.0 166.5 187.5 205.5 225.0 244.5 265.5
289.5 316.5 345.0
2250.0 | 15.0 33.0 52.5 70.5 88.5 108.0
127.5 147.0 168.0 187.5 207.0 228.0 250.5 271.5
294.0 316.5 340.5
2400.0 | 25.5 43.5 61.5 81.0 100.5 120.0
139.5 159.0 180.0 201.0 222.0 243.0 265.5 288.0
310.5 333.0 340.5
2550.0 | 36.0 52.5 69.0 87.0 105.0 124.5
142.5 162.0 181.5 201.0 222.0 241.5 262.5 283.5
306.0 328.5 340.5
Table of Hex Values
Pulse_width ->
-1.0 1.5 4.0 6.5 9.0 11.5
14.0 16.5 19.0 21.5 24.0 26.5 29.0 31.5
34.0 36.5 39.0
-----------------------------------------------------------------------------------
-----------------------------------------------------------------------------------
---------------------------------------
A 150.0 | 00 00 0c 21 37 4d
63 73 85 9b b0 c6 db ed
f3 fa ff
X 300.0 | 00 00 0b 20 35 4b
60 6f 81 96 ab c0 d5 eb
f1 f8 ff
I 450.0 | 00 00 0b 1f 33 48
5d 6d 7e 91 a5 ba cf e3
f0 f8 ff
S 600.0 | 00 00 08 1c 31 44
58 69 7a 8d a1 b5 c9 dd
f0 f7 ff
_ 750.0 | 00 01 0a 1c 2f 44
58 68 7a 8b 9d b0 c4 d8
eb f7 ff
R 900.0 | 00 02 0f 21 30 41
53 65 76 89 9b ab bf d2
e5 f3 fc
P 1050.0 | 00 01 13 23 32 40
50 62 75 85 95 a9 ba cc
df f0 fc
M 1200.0 | 00 02 14 21 2d 3c
4a 5b 6d 7e 8f a3 b7 c9
db ea fa
_ 1350.0 | 00 03 15 23 2e 39
4b 5c 6d 7b 8d 9f b1 c4
d3 e4 f7
1 1500.0 | 00 03 16 22 2d 3d
4c 5d 6d 7b 8a 9c ac bd
cf e1 f2
7 1650.0 | 00 0a 18 24 2f 3e
4d 5d 6e 7c 89 99 ab bb
cb db f0
1800.0 | 00 0d 1c 26 30 3f
4e 5e 6e 7c 89 98 a6 b5
c6 d6 ed
1950.0 | 01 10 1e 27 32 41
4f 5e 6f 7c 89 97 a4 b3
c1 d6 e9
2100.0 | 08 13 1f 2b 35 43
50 5e 6f 7d 89 96 a3 b1
c1 d3 e6
2250.0 | 0a 16 23 2f 3b 48
55 62 70 7d 8a 98 a7 b5
c4 d3 e3
2400.0 | 11 1d 29 36 43 50
5d 6a 78 86 94 a2 b1 c0
cf de e3
2550.0 | 18 23 2e 3a 46 53
5f 6c 79 86 94 a1 af bd
cc db e3
NAME: fuel_per_firing_pilot_time ADDR: 1C20 UNT: "" OWN: B CODE: fpfppt
EQN: (E+300)/20
Pulse width time based on rail press and FPC

Table of AXIS_BAR_9
BAR ->
300.0 450.0 600.0 750.0 900.0 1050.0
1200.0 1350.0 1500.0
-----------------------------------------------------------------------------------
----------------------------------
A 0.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
X 50.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
I 100.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
S 150.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 200.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
m 250.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
m 300.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
3 350.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 400.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1 450.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
7 500.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
550.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
600.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
650.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
700.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
750.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
800.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0

Table of Hex Values


BAR ->
300.0 450.0 600.0 750.0 900.0 1050.0
1200.0 1350.0 1500.0
-----------------------------------------------------------------------------------
----------------------------------
A 0.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
X 50.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
I 100.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
S 150.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
_ 200.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
m 250.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
m 300.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
3 350.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
_ 400.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
1 450.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
7 500.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
550.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
600.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
650.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
700.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
750.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
800.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f

NAME: fuel_per_firing_main_time ADDR: 1CB9 UNT: "" OWN: B CODE: fpfmpt


EQN: (E+300)/20
Pulse width time based on rail press and FPC

Table of AXIS_BAR_9
BAR ->
300.0 450.0 600.0 750.0 900.0 1050.0
1200.0 1350.0 1500.0
-----------------------------------------------------------------------------------
----------------------------------
A 0.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
X 50.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
I 100.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
S 150.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 200.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
m 250.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
m 300.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
3 350.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 400.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1 450.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
7 500.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
550.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
600.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
650.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
700.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
750.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
800.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0

Table of Hex Values


BAR ->
300.0 450.0 600.0 750.0 900.0 1050.0
1200.0 1350.0 1500.0
-----------------------------------------------------------------------------------
----------------------------------
A 0.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
X 50.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
I 100.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
S 150.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
_ 200.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
m 250.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
m 300.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
3 350.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
_ 400.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
1 450.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
7 500.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
550.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
600.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
650.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
700.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
750.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f
800.0 | 0f 0f 0f 0f 0f 0f
0f 0f 0f

NAME: fuel_temp_correction ADDR: 1D52 UNT: "" OWN: V CODE: futemp


EQN: E*128
Fuel Cnsmptn Temperature Compensation Table f(FTS)
dgC| HEX| ""
--------------------------------
-40.0| 8d| 1.102
-27.8| 8a| 1.078
-15.6| 89| 1.070
-3.3| 86| 1.047
8.9| 85| 1.039
21.1| 83| 1.023
33.3| 81| 1.008
45.6| 7f| 0.992
57.8| 7e| 0.984
70.0| 7a| 0.953
82.2| 79| 0.945
94.4| 79| 0.945
106.7| 79| 0.945
118.9| 79| 0.945
131.1| 79| 0.945
143.3| 79| 0.945
155.6| 79| 0.945

NAME: halfeng_max_torque ADDR: 1D63 UNT: "" OWN: B CODE: hetqmx


EQN: E*2.55
Torque>hetqmx half engine mode disabled f(RPM)
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00
300.0| 00| 0.00
450.0| 00| 0.00
600.0| 40| 25.10
750.0| 4d| 30.20
900.0| 5c| 36.08
1050.0| 54| 32.94
1200.0| 54| 32.94
1350.0| 00| 0.00
1500.0| 00| 0.00
1650.0| 00| 0.00
1800.0| 00| 0.00
1950.0| 00| 0.00
2100.0| 00| 0.00
2250.0| 00| 0.00
2400.0| 00| 0.00
2550.0| 00| 0.00

NAME: halfeng_torque_ratio ADDR: 1D74 UNT: "" OWN: V CODE: hetqrt


EQN: E*64
Ratio used in half eng mode to determine LTQ
RPM| HEX| ""
--------------------------------
150.0| 80| 2.000
300.0| 80| 2.000
450.0| 80| 2.000
600.0| 80| 2.000
750.0| 80| 2.000
900.0| 80| 2.000
1050.0| 80| 2.000
1200.0| 80| 2.000
1350.0| 80| 2.000
1500.0| 80| 2.000
1650.0| 80| 2.000
1800.0| 80| 2.000
1950.0| 80| 2.000
2100.0| 80| 2.000
2250.0| 80| 2.000
2400.0| 80| 2.000
2550.0| 80| 2.000

NAME: inj_detect_delay_table ADDR: 1D85 UNT: "" OWN: V CODE: irdtdl


EQN: E+128.000000
InjRespTime=ClosureDetect-IRDTDL

Table of AXIS_RailP-BAR_9
RailP-BAR ->
0.0 276.0 552.0 828.0 1104.0 1379.0
1655.0 1931.0 2207.0
-----------------------------------------------------------------------------------
----------------------------------
A 0.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
X 3.2 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
I 6.4 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
S 9.6 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 12.8 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
V 16.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
o 19.2 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
l 22.4 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
t 25.6 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
s 28.8 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
_ 32.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
1 35.2 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
7 38.4 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
41.6 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
44.8 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
48.0 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0
51.2 | 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0

Table of Hex Values


RailP-BAR ->
0.0 276.0 552.0 828.0 1104.0 1379.0
1655.0 1931.0 2207.0
-----------------------------------------------------------------------------------
----------------------------------
A 0.0 | 80 80 80 80 80 80
80 80 80
X 3.2 | 80 80 80 80 80 80
80 80 80
I 6.4 | 80 80 80 80 80 80
80 80 80
S 9.6 | 80 80 80 80 80 80
80 80 80
_ 12.8 | 80 80 80 80 80 80
80 80 80
V 16.0 | 80 80 80 80 80 80
80 80 80
o 19.2 | 80 80 80 80 80 80
80 80 80
l 22.4 | 80 80 80 80 80 80
80 80 80
t 25.6 | 80 80 80 80 80 80
80 80 80
s 28.8 | 80 80 80 80 80 80
80 80 80
_ 32.0 | 80 80 80 80 80 80
80 80 80
1 35.2 | 80 80 80 80 80 80
80 80 80
7 38.4 | 80 80 80 80 80 80
80 80 80
41.6 | 80 80 80 80 80 80
80 80 80
44.8 | 80 80 80 80 80 80
80 80 80
48.0 | 80 80 80 80 80 80
80 80 80
51.2 | 80 80 80 80 80 80
80 80 80

NAME: maximum_boi ADDR: 1E1E UNT: "" OWN: B CODE: maxboi


EQN: E*8
Max BOI to limit peak cylinder press f(RPM,load)

Table of AXIS_%_Torque_9
%_Torque ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 12.00 12.00 12.00 12.00 12.00 12.00
12.00 12.00 12.00
X 300.0 | 12.00 12.00 12.00 12.00 12.00 12.00
12.00 12.00 12.00
I 450.0 | 12.00 12.00 12.00 12.00 12.00 12.00
12.00 12.00 12.00
S 600.0 | 12.00 12.00 12.00 12.00 12.00 12.00
12.00 12.00 12.00
_ 750.0 | 15.00 15.00 15.00 15.00 15.00 15.00
15.00 15.00 15.00
R 900.0 | 16.00 16.00 16.00 16.00 16.00 16.00
16.00 16.00 16.00
P 1050.0 | 16.00 16.00 16.00 16.00 16.00 16.00
16.00 16.00 16.00
M 1200.0 | 16.00 16.00 16.00 16.00 16.00 19.00
19.00 19.00 14.00
_ 1350.0 | 16.00 16.00 16.00 16.00 16.00 18.00
18.00 17.00 13.00
1 1500.0 | 16.00 16.00 16.00 16.00 16.00 16.00
20.00 15.00 13.00
7 1650.0 | 16.00 16.00 16.00 16.00 17.00 20.00
20.00 15.00 13.00
1800.0 | 16.00 16.00 16.00 16.00 18.00 20.00
20.00 16.00 10.00
1950.0 | 16.00 16.00 16.00 16.00 19.00 21.00
20.00 17.00 10.00
2100.0 | 16.00 16.00 16.00 16.00 20.00 21.00
21.00 10.00 10.00
2250.0 | 16.00 16.00 16.00 16.00 20.00 20.00
16.00 10.00 10.00
2400.0 | 16.00 16.00 16.00 16.00 16.00 16.00
16.00 16.00 16.00
2550.0 | 16.00 16.00 16.00 16.00 16.00 16.00
16.00 16.00 16.00

Table of Hex Values


%_Torque ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 60 60 60 60 60 60
60 60 60
X 300.0 | 60 60 60 60 60 60
60 60 60
I 450.0 | 60 60 60 60 60 60
60 60 60
S 600.0 | 60 60 60 60 60 60
60 60 60
_ 750.0 | 78 78 78 78 78 78
78 78 78
R 900.0 | 80 80 80 80 80 80
80 80 80
P 1050.0 | 80 80 80 80 80 80
80 80 80
M 1200.0 | 80 80 80 80 80 98
98 98 70
_ 1350.0 | 80 80 80 80 80 90
90 88 68
1 1500.0 | 80 80 80 80 80 80
a0 78 68
7 1650.0 | 80 80 80 80 88 a0
a0 78 68
1800.0 | 80 80 80 80 90 a0
a0 80 50
1950.0 | 80 80 80 80 98 a8
a0 88 50
2100.0 | 80 80 80 80 a0 a8
a8 50 50
2250.0 | 80 80 80 80 a0 a0
80 50 50
2400.0 | 80 80 80 80 80 80
80 80 80
2550.0 | 80 80 80 80 80 80
80 80 80

NAME: rail_p_pw_mult ADDR: 1EB7 UNT: "" OWN: V CODE: rppwml


EQN: E*85
FPW=PW*RPPWML as f(actual/desired rail press)
Ratio| HEX| ""
--------------------------------
0.0| 55| 1.000
0.1| 55| 1.000
0.3| 55| 1.000
0.4| 55| 1.000
0.5| 55| 1.000
0.6| 55| 1.000
0.8| 55| 1.000
0.9| 55| 1.000
1.0| 55| 1.000
1.1| 55| 1.000
1.3| 55| 1.000
1.4| 55| 1.000
1.5| 55| 1.000
1.6| 55| 1.000
1.8| 55| 1.000
1.9| 55| 1.000
2.0| 55| 1.000

NAME: split_ip_gap ADDR: 1EC8 UNT: "" OWN: B CODE: epiipg


EQN: E*8
Crank degs from pilot pulse EOI to main BOI
RPM| HEX| ""
--------------------------------
150.0| 38| 7.00
300.0| 3c| 7.50
450.0| 40| 8.00
600.0| 44| 8.50
750.0| 48| 9.00
900.0| 50| 10.00
1050.0| 58| 11.00
1200.0| 60| 12.00
1350.0| 60| 12.00
1500.0| 60| 12.00
1650.0| 60| 12.00
1800.0| 60| 12.00
1950.0| 60| 12.00
2100.0| 60| 12.00
2250.0| 60| 12.00
2400.0| 60| 12.00
2550.0| 60| 12.00

NAME: split_main_pulse_width_corr ADDR: 1ED9 UNT: "" OWN: V CODE:


spmpwc EQN: E/2
MPW=MPW + spmpwc
Volts| HEX| ""
--------------------------------
6.4| 00| 0.0
9.6| 00| 0.0
12.8| 00| 0.0
16.0| 00| 0.0
19.2| 00| 0.0
22.4| 00| 0.0
25.6| 00| 0.0
28.8| 00| 0.0
32.0| 00| 0.0

NAME: split_max_boi ADDR: 1EE2 UNT: "" OWN: V CODE: smxboi


EQN: E*8
max allowable BOI=SMXBOI if SPLIT INJ enabled
RPM| HEX| ""
--------------------------------
150.0| 90| 18.00
300.0| 90| 18.00
450.0| 90| 18.00
600.0| 90| 18.00
750.0| 98| 19.00
900.0| a0| 20.00
1050.0| a0| 20.00
1200.0| a0| 20.00
1350.0| a0| 20.00
1500.0| a0| 20.00
1650.0| a0| 20.00
1800.0| a0| 20.00
1950.0| a0| 20.00
2100.0| a0| 20.00
2250.0| a0| 20.00
2400.0| a0| 20.00
2550.0| a0| 20.00

NAME: split_main_irt_mult ADDR: 1EF3 UNT: "" OWN: V CODE: epirtm


EQN: (E-0.5)*255
if epimrt is set, IRTM=IRT*epirtm*epirmc
GAP_uSec| HEX| ""
--------------------------------
0.0| 01| 0.5039
300.0| 01| 0.5039
600.0| 01| 0.5039
900.0| 01| 0.5039
1200.0| 01| 0.5039
1500.0| 01| 0.5039
1800.0| 01| 0.5039
2100.0| 01| 0.5039
2400.0| 01| 0.5039
NAME: split_main_irt_mult_corr ADDR: 1EFC UNT: "" OWN: V CODE: epirmc
EQN: E*255
If epimrt is set, IRTM=IRT*epirtm*epirmc
Volts| HEX| ""
--------------------------------
6.4| 00| 0.0000
9.6| 00| 0.0000
12.8| 00| 0.0000
16.0| 00| 0.0000
19.2| 00| 0.0000
22.4| 00| 0.0000
25.6| 00| 0.0000
28.8| 00| 0.0000
32.0| 00| 0.0000

NAME: split_pilot_max_fpc ADDR: 1F05 UNT: "" OWN: B CODE: epxfpc


EQN: E/2
Max pilot fuel per cycle for max pilot pulse time
BAR| HEX| ""
--------------------------------
0.0| 00| 0.0
150.0| 00| 0.0
300.0| 00| 0.0
450.0| 00| 0.0
600.0| 00| 0.0
750.0| 00| 0.0
900.0| 00| 0.0
1050.0| 00| 0.0
1200.0| 00| 0.0
1350.0| 00| 0.0
1500.0| 00| 0.0
1650.0| 00| 0.0
1800.0| 00| 0.0
1950.0| 00| 0.0
2100.0| 00| 0.0
2250.0| 00| 0.0
2400.0| 00| 0.0

NAME: split_pilot_max_pulse_time ADDR: 1F16 UNT: "" OWN: B CODE: epxpwt


EQN: (E+300)/20
Max common rail pilot pulse width time
RPM| HEX| ""
--------------------------------
150.0| 3b| 880.0
300.0| 3b| 880.0
450.0| 32| 700.0
600.0| 2d| 600.0
750.0| 2d| 600.0
900.0| 2c| 580.0
1050.0| 2c| 580.0
1200.0| 2c| 580.0
1350.0| 2c| 580.0
1500.0| 2b| 560.0
1650.0| 29| 520.0
1800.0| 29| 520.0
1950.0| 29| 520.0
2100.0| 29| 520.0
2250.0| 29| 520.0
2400.0| 29| 520.0
2550.0| 29| 520.0

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
air_temp_fan_adv_delta 1F27 2.78 dgC 28 E*14.4 V
atadvd Delta abv atf1on or abv atoff for boi adv on/off
boi_load_axis 1F28 2 = torque.proportional2 =
torque.proportional B boiax BOI load axis definition: 0=TPS 1=FTQ 2=FTQP >2=?
cool_temp_fan_adv_delta 1F29 2.78 dgC 28 E*14.4 V
ctadvd Delta abv ctf1on or abv ctoff for boi adv on/off
fuel_per_firing_max 1F2A 800.0 Cubi c8 E/4 B
fpcmax Maximum amount of fuel per cylinder firing
halfeng_delta_timer 1F2B 0.0 SEC 00 E V
hedtmr max IgnON sec FTQ<HETQMX+HEMTQD-HETQHY w/HEMTQD<>0
halfeng_max_torque_delta 1F2C 0.00 %TQ 00 E*2.55 V
hemtqd added to HETQMX if HEDTMR & HEMXDT tests satisfied
halfeng_mph_hyst 1F2D 2.0 MPH 04 E*2 V
hevshy MPH < HEMXVS-HEVSHY to re-enable HalfEngine
halfeng_temp_hyst 1F2E 3.9 dgC 07 E*1.8 V
hetehy half engine mode enable: oil temp hysteresis
halfeng_torque_hyst 1F2F 7.84 % 14 E*2.55 V
hetqhy half engine mode enable: %FTQ hysteresis (*ztqscl)
halfeng_temp_weighting 1F30 1.000 WGT 80 E*128 V
hefac HALENG temp weighting: degC=F*HEPD1+(1-F)*HEPD0
hp_pump_default_max_util 1F31 0.8000 %PU cc E*255 V
hpdmxu max %PumpUtilization if utilization fault
hp_pump_default_min_util 1F32 0.4000 %PU 66 E*255 V
hpdmnu min %PumpUtilization if utilization fault
initial_pump_utilization 1F33 0.5020 %PU 80 E*255 V
utlini %PumpUtilization before pump controller enabled
inj_cal_code_method 1F34 0.0 Flg 00 E V
icmeth InjCalCodes:0=std EUI multiplier/1=S4000 2pt comp
inj_turn_del_cal_increment 1F35 20.0 uSC 28 E*2 V
itodic multiplier which maps InjCal table to PW offset
inj_turn_del_max_cal_pw_time 1F36 2805.0 uSC bb E/15 V
itodmx nominal high press and flow PW in usec
inj_turn_del_min_cal_pw_time 1F37 1305.0 uSC 57 E/15 V
itodmn nominal low press and flow PW in usec
maximum_pump_utilization 1F38 0.9765 %PU f9 E*255 V
maxutl %PumpUtilization>MAXUTL to log high utilztn fault
minimum_pump_utilization 1F39 0.0235 %PU 06 E*255 V
minutl %PumpUtilization<MINUTL to log low utiliztn fault
pump_utilization_fault_timer 1F3A 10.0 SEC 0a E V
utltim %PumpUtil fault present for >UTLTIM to log fault
pwm_fan_adv_hyst 1F3B 1.11 dgC 10 E*14.4 V
pfahy Delta abv atf1on or abv atoff for boi adv on/off
pulse_width_time_max 1F3C 4800.0 Micr ff (E+300)/20 B
pwtmax Maximum pulse width time allowed
split_adv_disable 1F3D 31.88 DEG ff E*8 V
epadis if BOI>EPADIS then SPLIT INJ disabled
split_temp_hyst 1F3E 2.2 dgC 04 E*1.8 V
epithy temp below epimxt to allow split to remain enabled
split_temp_weighting 1F3F 0.000 unit 00 E*128 V
epitwf Weight factor for epipd1 | epipd0 wt=(1-epitwf)
split_min_voltage 1F40 0.00 VLT 00 E*5 V
epimnv EPI disabled below epimnv
split_volt_hyst 1F41 1.00 VLT 05 E*5 V
epibhy EPI re-allowed above epimnv+epibhy
halfeng_on_parkbrake 1F42 1.0 Flg 1 E V
heonpb Set to allow HALFENG only if park brake enabled
halfeng_on_governor 1F42.1 0.0 Flg 0 E V
heongv Set to allow HALFENG only if idle governor active
halfeng_no_re_enter 1F42.2 0.0 Flg 0 E V
henore Half ENG: Set to not re-enter 1/2 eng on cool down
half_engine_odd_even 1F42.3 0.0 Flg 0 E V
heodd 16V4000 HALFENG: 0=all mstr / 1=odd mstr+odd rcvr
common_rail_fpc_pw_mapping 1F42.4 0.0 Flg 0 E B
fpcpw if set, calculate pulse width using fuel per cycle
broadcast_pw_as_fpc 1F42.5 0.0 Flg 0 E B
txpwus if set, ID150 and ID162 broadcast @ mm3/100
boi_special_in_cc 1F42.6 0.0 Flg 0 E V
boicc BOI: Use only top row of BOI Table in cruise cntrl
acb_enabled 1F42.7 1.0 Flg 1 E V
acbenb set to enable Adaptive Cylinder Balancing on S60
split_in_smoke_mode 1F43 0.0 Flg 0 E V
epismk set to enable SPLIT INJ in smoke control mode
split_in_normal_mode 1F43.1 0.0 Flg 0 E V
epinmd set to enable SPLIT INJ in NORMAL run/idle mode
split_in_half_engine_mode 1F43.2 1.0 Flg 1 E V
epihmd set to enable SPLIT INJECTION in HALF ENGINE mode
split_at_idle 1F43.3 0.0 Flg 0 E V
epidle if epienb set-set to enable SPLIT INJ at IDLE only
split_estimate_main_irt 1F43.4 0.0 Flg 0 E V
epimrt If epimrt is set, IRTm=IRT*epirtm*epirmc
split_after_start_mode 1F43.5 1.0 Flg 1 E V
episme set for split after start for 30 sec max f(OilTmp)
rail_p_inj_compensation 1F43.6 0.0 Flg 0 E V
rpinen Set for S4000 fuel rail pressure injection cmpnstn
pwm_clock_divide 1F43.7 0.0 Flg 0 E V
pwckdv Set for TPUclock/4 for 8Hz min PWMfreq w/ less res
split_mpw_table_axis_is_ltq 1F44.5 0.0 Flg 0 E V
smtail If set, LTQ->prvmpw, else MTQ->prvmpw
split_irt_is_pilot 1F44.6 0.0 Flg 0 E V
epiirt set IRTraw=IRTpilot, else IRTraw=IRTmain when splt
split_in_start_mode 1F44.7 1.0 Flg 1 E B
epismd set to enable SPLIT INJECTION in START mode
checksum_rat0 1F46 33997.0 HEX 84cd E C
# Filled by Cal Tools
fuel_type_rat0 1F48 95.0 DEC 5f E C
fuelrt Fueltp = 95 for diesel and Fueltp = 160 for Gas
rating_edit_version_rat0 1F49 29.0 "" 1d E C
rrlvrr rating_edit_version_rat0

NAME: filtq_smoke_torque_rat0 ADDR: 1F4A UNT: "" OWN: B CODE: fltsmt


EQN: E*20.47
smoke limit tq offset due to filt final tq
%_Torque| HEX| ""
--------------------------------
0.0| ffffff71| -6.986
6.3| ffffff85| -6.009
12.5| ffffff9a| -4.983
18.8| ffffffc3| -2.980
25.0| ffffffd7| -2.003
31.3| ffffffec| -0.977
37.5| 0000| 0.000
43.8| 0000| 0.000
50.0| 0000| 0.000
56.3| 0000| 0.000
62.5| 0000| 0.000
68.8| 0000| 0.000
75.0| 0000| 0.000
81.3| 0000| 0.000
87.5| 0000| 0.000
93.8| 0000| 0.000
100.0| 0000| 0.000

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
actual_peak_torque_value_rat0 1F6C 1550.0 FT# 060e E B
peaktq Rating 0 Peak Torque in foot*lbs
peak_torque_rpm_rat0 1F6E 1200.00 RPM 12c0 E*4 B
ptqrpm RPM at which engine delivers peak torque for rtg0
rated_horse_power_rat0 1F70 430.0 BHP 01ae E B
ratbhp rated brake horsepower for rating 0
rated_max_rpm_rat0 1F72 2110.00 RPM 20f8 E*4 B
ratrpm rated engine RPM for rating 0

NAME: boi_torque_reduction_rat0 ADDR: 1F74 UNT: "" OWN: B CODE: rpmtqc


EQN: E*2048
%TQ redux/deg BOI advance from adaptv or temp-rat0
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00000
300.0| 00| 0.00000
450.0| 00| 0.00000
600.0| 0a| 0.00488
750.0| 06| 0.00293
900.0| 04| 0.00195
1050.0| 00| 0.00000
1200.0| fffffffc| -0.00195
1350.0| fffffff7| -0.00439
1500.0| fffffff4| -0.00586
1650.0| fffffff3| -0.00635
1800.0| fffffff6| -0.00488
1950.0| fffffff8| -0.00391
2100.0| fffffffd| -0.00146
2250.0| 00| 0.00000
2400.0| 00| 0.00000
2550.0| 00| 0.00000

NAME: base_air_temp_offset_boi_rat0 ADDR: 1F85 UNT: "" OWN: B CODE:


basboi EQN: E*4
delta BOI as a f(air temperature)
dgC| HEX| ""
--------------------------------
-40.0| 00| 0.00
-27.8| 00| 0.00
-15.6| 00| 0.00
-3.3| 00| 0.00
8.9| 00| 0.00
21.1| 00| 0.00
33.3| 00| 0.00
45.6| 00| 0.00
57.8| 00| 0.00
70.0| 00| 0.00
82.2| 00| 0.00
94.4| 00| 0.00
106.7| 00| 0.00
118.9| 00| 0.00
131.1| 00| 0.00
143.3| 00| 0.00
155.6| 00| 0.00

NAME: filtq_offset_boi_rat0 ADDR: 1F96 UNT: "" OWN: B CODE: fltboi


EQN: E*4
BOI offset due to filt final tq
%_Torque| HEX| ""
--------------------------------
0.0| 02| 0.50
6.3| 02| 0.50
12.5| 00| 0.00
18.8| fffffff8| -2.00
25.0| fffffff4| -3.00
31.3| fffffff0| -4.00
37.5| fffffff0| -4.00
43.8| ffffffe8| -6.00
50.0| ffffffe8| -6.00
56.3| ffffffe8| -6.00
62.5| fffffff0| -4.00
68.8| fffffff0| -4.00
75.0| 00| 0.00
81.3| 00| 0.00
87.5| 00| 0.00
93.8| 00| 0.00
100.0| 00| 0.00

NAME: filtq_smoke_boi_rat0 ADDR: 1FA7 UNT: "" OWN: B CODE: fltscb


EQN: E*4
BOI offset due to filt final tq when in smoke mode
%_Torque| HEX| ""
--------------------------------
0.0| 1c| 7.00
6.3| 18| 6.00
12.5| 14| 5.00
18.8| 10| 4.00
25.0| 0c| 3.00
31.3| 00| 0.00
37.5| 00| 0.00
43.8| 00| 0.00
50.0| 00| 0.00
56.3| 00| 0.00
62.5| 00| 0.00
68.8| 00| 0.00
75.0| 00| 0.00
81.3| 00| 0.00
87.5| 00| 0.00
93.8| 00| 0.00
100.0| 00| 0.00

NAME: requested_torque_rat0 ADDR: 1FB8 UNT: "" OWN: B CODE: rtqif


EQN: E*2.55
Rating 0 Requested Torque Table f(RPM,%throttle)

Table of AXIS_%_Throttle_9
%_Throttle ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.00 39.22 39.22 39.22 39.22 39.22
39.22 39.22 39.22
X 300.0 | 0.00 30.98 39.22 39.22 39.22 39.22
39.22 39.22 39.22
I 450.0 | 0.00 20.78 39.61 39.61 39.61 39.61
39.61 39.61 39.61
S 600.0 | 0.00 15.69 30.98 40.00 40.00 40.00
40.00 40.00 40.00
_ 750.0 | 0.00 12.55 24.71 37.25 52.94 52.94
52.94 52.94 52.94
R 900.0 | 0.00 10.20 20.78 30.98 56.08 65.88
65.88 65.88 65.88
P 1050.0 | 0.00 9.02 17.65 26.67 47.84 69.41
78.82 78.82 78.82
M 1200.0 | 0.00 7.84 15.69 23.14 41.96 60.78
79.22 92.16 92.16
_ 1350.0 | 0.00 7.06 13.73 20.78 37.25 53.73
70.59 87.06 92.55
1 1500.0 | 0.00 6.27 12.55 18.82 33.73 51.76
69.41 87.45 93.33
7 1650.0 | 0.00 5.49 11.37 16.86 30.59 47.45
64.71 81.57 87.45
1800.0 | 0.00 5.10 10.20 15.69 27.84 43.92
60.00 76.08 81.18
1950.0 | 0.00 4.71 9.41 14.51 25.88 40.78
55.69 70.20 75.29
2100.0 | 0.00 4.31 9.02 13.33 23.92 37.65
50.98 64.71 69.41
2250.0 | 0.00 4.31 8.24 12.55 22.35 34.51
47.06 59.22 63.14
2400.0 | 0.00 3.92 7.84 11.76 20.00 20.00
20.00 20.00 20.00
2550.0 | 0.00 3.53 7.45 10.98 19.61 19.61
20.00 20.00 20.00

Table of Hex Values


%_Throttle ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 64 64 64 64 64
64 64 64
X 300.0 | 00 4f 64 64 64 64
64 64 64
I 450.0 | 00 35 65 65 65 65
65 65 65
S 600.0 | 00 28 4f 66 66 66
66 66 66
_ 750.0 | 00 20 3f 5f 87 87
87 87 87
R 900.0 | 00 1a 35 4f 8f a8
a8 a8 a8
P 1050.0 | 00 17 2d 44 7a b1
c9 c9 c9
M 1200.0 | 00 14 28 3b 6b 9b
ca eb eb
_ 1350.0 | 00 12 23 35 5f 89
b4 de ec
1 1500.0 | 00 10 20 30 56 84
b1 df ee
7 1650.0 | 00 0e 1d 2b 4e 79
a5 d0 df
1800.0 | 00 0d 1a 28 47 70
99 c2 cf
1950.0 | 00 0c 18 25 42 68
8e b3 c0
2100.0 | 00 0b 17 22 3d 60
82 a5 b1
2250.0 | 00 0b 15 20 39 58
78 97 a1
2400.0 | 00 0a 14 1e 33 33
33 33 33
2550.0 | 00 09 13 1c 32 32
33 33 33

NAME: smoke_control_boi_rat0 ADDR: 2051 UNT: "" OWN: B CODE: scboi


EQN: E*8
smoke_control_boi_rat0
RPM| HEX| ""
--------------------------------
150.0| 38| 7.00
300.0| 38| 7.00
450.0| 38| 7.00
600.0| 38| 7.00
750.0| 38| 7.00
900.0| 38| 7.00
1050.0| 38| 7.00
1200.0| 38| 7.00
1350.0| 38| 7.00
1500.0| 30| 6.00
1650.0| 30| 6.00
1800.0| 30| 6.00
1950.0| 30| 6.00
2100.0| 30| 6.00
2250.0| 30| 6.00
2400.0| 30| 6.00
2550.0| 30| 6.00

NAME: smoke_limiting_torque_rat0 ADDR: 2062 UNT: "" OWN: B CODE: sctorq


EQN: E*2.55
smoke control TORQUE Table rating0 f(RPM,boost)

Table of AXIS_derived_smoke_control_9
derived_smoke_control ->
14.0 84.3 94.6 106.5 121.2 139.5
159.2 179.9 221.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 71.76 71.76 71.76 71.76 71.76 71.76
71.76 71.76 71.76
X 300.0 | 71.76 71.76 71.76 71.76 71.76 71.76
71.76 71.76 71.76
I 450.0 | 33.33 33.33 35.69 38.82 43.92 43.92
43.92 43.92 43.92
S 600.0 | 39.61 39.61 39.61 41.57 43.14 50.20
50.20 50.20 50.20
_ 750.0 | 40.00 40.00 40.00 46.67 52.94 56.86
60.00 61.96 65.10
R 900.0 | 41.96 41.96 43.92 52.94 56.86 61.96
74.90 87.06 100.00
P 1050.0 | 43.53 43.53 45.10 54.12 56.86 65.88
74.90 94.51 100.00
M 1200.0 | 45.10 45.10 45.10 54.12 56.86 66.27
73.73 90.98 100.00
_ 1350.0 | 45.10 45.10 45.10 52.55 58.43 65.49
80.78 90.98 100.00
1 1500.0 | 45.88 45.88 45.88 53.73 59.22 65.88
77.25 90.98 100.00
7 1650.0 | 47.06 47.06 47.06 52.94 58.04 67.06
78.82 92.16 100.00
1800.0 | 47.84 47.84 47.84 54.12 58.04 67.84
78.82 90.98 100.00
1950.0 | 47.84 47.84 47.84 54.12 56.08 63.14
80.00 89.80 100.00
2100.0 | 48.63 47.84 47.84 54.90 56.08 63.92
80.00 89.80 100.00
2250.0 | 49.02 49.02 43.14 56.47 60.00 67.84
79.61 89.80 100.00
2400.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
2550.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00

Table of Hex Values


derived_smoke_control ->
14.0 84.3 94.6 106.5 121.2 139.5
159.2 179.9 221.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | b7 b7 b7 b7 b7 b7
b7 b7 b7
X 300.0 | b7 b7 b7 b7 b7 b7
b7 b7 b7
I 450.0 | 55 55 5b 63 70 70
70 70 70
S 600.0 | 65 65 65 6a 6e 80
80 80 80
_ 750.0 | 66 66 66 77 87 91
99 9e a6
R 900.0 | 6b 6b 70 87 91 9e
bf de ff
P 1050.0 | 6f 6f 73 8a 91 a8
bf f1 ff
M 1200.0 | 73 73 73 8a 91 a9
bc e8 ff
_ 1350.0 | 73 73 73 86 95 a7
ce e8 ff
1 1500.0 | 75 75 75 89 97 a8
c5 e8 ff
7 1650.0 | 78 78 78 87 94 ab
c9 eb ff
1800.0 | 7a 7a 7a 8a 94 ad
c9 e8 ff
1950.0 | 7a 7a 7a 8a 8f a1
cc e5 ff
2100.0 | 7c 7a 7a 8c 8f a3
cc e5 ff
2250.0 | 7d 7d 6e 90 99 ad
cb e5 ff
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: torque_adjustment_rat0 ADDR: 20FB UNT: "" OWN: B CODE: tqadj


EQN: E*1024
Set to 0 / PW Tbl TRQ developed for BOI rtg0
RPM| HEX| ""
--------------------------------
150.0| 00| 0.0000
300.0| 00| 0.0000
450.0| 00| 0.0000
600.0| 29| 0.0400
750.0| 29| 0.0400
900.0| 1d| 0.0283
1050.0| 12| 0.0176
1200.0| 1f| 0.0303
1350.0| 0e| 0.0137
1500.0| 17| 0.0225
1650.0| 17| 0.0225
1800.0| 24| 0.0352
1950.0| 17| 0.0225
2100.0| 07| 0.0068
2250.0| 00| 0.0000
2400.0| 00| 0.0000
2550.0| 00| 0.0000

NAME: torque_ss_rat0 ADDR: 210C UNT: "" OWN: B CODE: sstqrd


EQN: E*2048
steady state TQ reduction due to BOI
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00000
300.0| 00| 0.00000
450.0| 00| 0.00000
600.0| 0e| 0.00684
750.0| 06| 0.00293
900.0| 03| 0.00146
1050.0| fffffffe| -0.00098
1200.0| fffffff8| -0.00391
1350.0| fffffff3| -0.00635
1500.0| fffffff2| -0.00684
1650.0| fffffff2| -0.00684
1800.0| ffffffee| -0.00879
1950.0| ffffffed| -0.00928
2100.0| fffffff1| -0.00732
2250.0| 00| 0.00000
2400.0| 00| 0.00000
2550.0| 00| 0.00000

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
rating_version_number_rat0 211D 102.0 DEC 66 E B
ratver Rating 0 Base Calibration Version No. for ID only

NAME: boi_table_rat0 ADDR: 211E UNT: "" OWN: B CODE: boifnc


EQN: E*8
BOI table rating 0 - function RPM and %load

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 6.00 6.00 6.00 6.00 6.00 6.00
6.00 6.00 6.00
X 300.0 | 6.00 6.00 6.00 6.00 6.00 6.00
6.00 6.00 6.00
I 450.0 | 3.00 3.00 3.00 4.00 4.00 4.00
4.00 4.00 4.00
S 600.0 | 3.00 3.00 3.00 4.00 4.00 4.00
4.00 4.00 4.00
_ 750.0 | 3.00 3.00 3.00 4.00 4.00 4.00
4.00 4.00 4.00
R 900.0 | 6.00 6.00 6.00 6.00 6.00 6.00
6.00 6.00 5.00
P 1050.0 | 8.00 8.00 7.00 6.00 6.00 6.00
6.00 6.00 6.00
M 1200.0 | 8.00 8.00 6.00 6.00 6.00 6.00
6.25 7.00 7.00
_ 1350.0 | 8.00 7.00 6.00 6.00 6.00 6.00
8.00 8.00 7.00
1 1500.0 | 8.00 7.00 6.00 2.50 2.00 2.00
2.00 2.00 6.00
7 1650.0 | 8.00 7.00 6.00 2.50 1.00 1.00
1.00 1.00 6.00
1800.0 | 8.00 7.00 6.00 2.50 0.00 0.00
0.00 0.00 7.00
1950.0 | 8.00 7.00 6.00 2.50 0.00 0.00
0.00 0.00 7.00
2100.0 | 8.00 7.00 6.00 2.50 0.00 0.00
0.00 0.00 7.00
2250.0 | 8.00 7.00 6.00 2.50 0.00 0.00
0.00 0.00 7.00
2400.0 | 9.00 9.00 6.00 4.00 4.00 4.00
4.00 4.00 4.00
2550.0 | 9.00 9.00 6.00 8.00 8.00 8.00
8.00 8.00 4.00

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 30 30 30 30 30 30
30 30 30
X 300.0 | 30 30 30 30 30 30
30 30 30
I 450.0 | 18 18 18 20 20 20
20 20 20
S 600.0 | 18 18 18 20 20 20
20 20 20
_ 750.0 | 18 18 18 20 20 20
20 20 20
R 900.0 | 30 30 30 30 30 30
30 30 28
P 1050.0 | 40 40 38 30 30 30
30 30 30
M 1200.0 | 40 40 30 30 30 30
32 38 38
_ 1350.0 | 40 38 30 30 30 30
40 40 38
1 1500.0 | 40 38 30 14 10 10
10 10 30
7 1650.0 | 40 38 30 14 08 08
08 08 30
1800.0 | 40 38 30 14 00 00
00 00 38
1950.0 | 40 38 30 14 00 00
00 00 38
2100.0 | 40 38 30 14 00 00
00 00 38
2250.0 | 40 38 30 14 00 00
00 00 38
2400.0 | 48 48 30 20 20 20
20 20 20
2550.0 | 48 48 30 40 40 40
40 40 20

NAME: boi_ss_rat0 ADDR: 21B7 UNT: "" OWN: B CODE: boissr


EQN: E*8
BOI table rating 0 for steady state

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 12.00 12.00 12.00 12.00 12.00 12.00
12.00 12.00 12.00
X 300.0 | 12.00 12.00 12.00 12.00 12.00 12.00
12.00 12.00 12.00
I 450.0 | 10.00 10.00 10.00 12.00 12.00 12.00
12.00 12.00 12.00
S 600.0 | 10.00 10.00 10.00 12.00 12.00 12.00
12.00 12.00 12.00
_ 750.0 | 10.00 10.00 10.00 15.00 15.00 15.00
15.00 15.00 15.00
R 900.0 | 15.00 15.00 14.00 14.00 16.00 16.00
16.00 16.00 16.00
P 1050.0 | 15.00 15.00 8.00 8.00 8.00 8.00
8.00 8.00 9.00
M 1200.0 | 15.00 15.00 7.00 7.00 7.00 8.00
8.00 8.00 10.50
_ 1350.0 | 15.00 15.00 8.00 9.50 10.00 10.00
10.00 10.50 11.13
1 1500.0 | 15.00 15.00 9.25 10.00 11.00 11.00
11.00 11.00 12.00
7 1650.0 | 15.00 15.00 9.25 10.00 11.00 11.00
11.00 11.00 12.00
1800.0 | 15.00 15.00 8.00 7.50 8.00 8.00
8.00 8.00 12.00
1950.0 | 15.00 15.00 10.00 7.00 7.00 8.00
8.00 8.00 11.00
2100.0 | 15.00 15.00 12.00 10.00 10.00 10.00
10.00 10.00 12.00
2250.0 | 15.00 15.00 12.00 11.00 11.00 11.00
11.00 11.00 12.00
2400.0 | 15.00 15.00 15.00 15.00 15.00 15.00
15.00 15.00 15.00
2550.0 | 31.88 31.88 31.88 31.88 31.88 31.88
31.88 31.88 31.88

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 60 60 60 60 60 60
60 60 60
X 300.0 | 60 60 60 60 60 60
60 60 60
I 450.0 | 50 50 50 60 60 60
60 60 60
S 600.0 | 50 50 50 60 60 60
60 60 60
_ 750.0 | 50 50 50 78 78 78
78 78 78
R 900.0 | 78 78 70 70 80 80
80 80 80
P 1050.0 | 78 78 40 40 40 40
40 40 48
M 1200.0 | 78 78 38 38 38 40
40 40 54
_ 1350.0 | 78 78 40 4c 50 50
50 54 59
1 1500.0 | 78 78 4a 50 58 58
58 58 60
7 1650.0 | 78 78 4a 50 58 58
58 58 60
1800.0 | 78 78 40 3c 40 40
40 40 60
1950.0 | 78 78 50 38 38 40
40 40 58
2100.0 | 78 78 60 50 50 50
50 50 60
2250.0 | 78 78 60 58 58 58
58 58 60
2400.0 | 78 78 78 78 78 78
78 78 78
2550.0 | ff ff ff ff ff ff
ff ff ff

NAME: split_pilot_boi_offset_rat0 ADDR: 2250 UNT: "" OWN: B CODE:


eppboi EQN: E*8
BOIpilot = min(absboi, BOI+eppboi)
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00
300.0| 00| 0.00
450.0| 00| 0.00
600.0| 00| 0.00
750.0| 00| 0.00
900.0| 00| 0.00
1050.0| 00| 0.00
1200.0| 00| 0.00
1350.0| 00| 0.00
1500.0| 00| 0.00
1650.0| 00| 0.00
1800.0| 00| 0.00
1950.0| 00| 0.00
2100.0| 00| 0.00
2250.0| 00| 0.00
2400.0| 00| 0.00
2550.0| 00| 0.00

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
checksum_rat1 2262 35847.0 HEX 8c07 E C
# Filled by Cal Tools
fuel_type_rat1 2264 95.0 DEC 5f E C
fuelrt Fueltp = 95 for diesel and Fueltp = 160 for Gas
rating_edit_version_rat1 2265 29.0 "" 1d E C
rrlvrr rating_edit_version_rat1

NAME: filtq_smoke_torque_rat1 ADDR: 2266 UNT: "" OWN: B CODE: fltsmt


EQN: E*20.47
smoke limit tq offset due to filt final tq
%_Torque| HEX| ""
--------------------------------
0.0| ffffff5c| -8.012
6.3| ffffff85| -6.009
12.5| ffffff9a| -4.983
18.8| ffffffae| -4.006
25.0| ffffffc3| -2.980
31.3| ffffffd7| -2.003
37.5| 0000| 0.000
43.8| 0000| 0.000
50.0| 0000| 0.000
56.3| 0000| 0.000
62.5| 0000| 0.000
68.8| 0000| 0.000
75.0| 0000| 0.000
81.3| 0000| 0.000
87.5| 0000| 0.000
93.8| 0000| 0.000
100.0| 0000| 0.000

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
actual_peak_torque_value_rat1 2288 1550.0 FT# 060e E B
peaktq Rating 1 Peak Torque in foot*lbs
peak_torque_rpm_rat1 228A 1200.00 RPM 12c0 E*4 B
ptqrpm RPM at which engine delivers peak torque for rtg1
rated_horse_power_rat1 228C 400.0 BHP 0190 E B
ratbhp rated brake horsepower for rating 1
rated_max_rpm_rat1 228E 2110.00 RPM 20f8 E*4 B
ratrpm rated engine RPM for rating 1

NAME: boi_torque_reduction_rat1 ADDR: 2290 UNT: "" OWN: B CODE: rpmtqc


EQN: E*2048
%TQ redux/deg BOI advance from adaptv or temp-rat1
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00000
300.0| 00| 0.00000
450.0| 00| 0.00000
600.0| 0a| 0.00488
750.0| 06| 0.00293
900.0| 04| 0.00195
1050.0| 00| 0.00000
1200.0| fffffffc| -0.00195
1350.0| fffffff7| -0.00439
1500.0| fffffff4| -0.00586
1650.0| fffffff3| -0.00635
1800.0| fffffff6| -0.00488
1950.0| fffffff8| -0.00391
2100.0| fffffffe| -0.00098
2250.0| 00| 0.00000
2400.0| 00| 0.00000
2550.0| 00| 0.00000

NAME: base_air_temp_offset_boi_rat1 ADDR: 22A1 UNT: "" OWN: B CODE:


basboi EQN: E*4
delta BOI as a f(air temperature)
dgC| HEX| ""
--------------------------------
-40.0| 00| 0.00
-27.8| 00| 0.00
-15.6| 00| 0.00
-3.3| 00| 0.00
8.9| 00| 0.00
21.1| 00| 0.00
33.3| 00| 0.00
45.6| 00| 0.00
57.8| 00| 0.00
70.0| 00| 0.00
82.2| 00| 0.00
94.4| 00| 0.00
106.7| 00| 0.00
118.9| 00| 0.00
131.1| 00| 0.00
143.3| 00| 0.00
155.6| 00| 0.00

NAME: filtq_offset_boi_rat1 ADDR: 22B2 UNT: "" OWN: B CODE: fltboi


EQN: E*4
BOI offset due to filt final tq
%_Torque| HEX| ""
--------------------------------
0.0| 00| 0.00
6.3| 00| 0.00
12.5| fffffffc| -1.00
18.8| fffffff8| -2.00
25.0| fffffff4| -3.00
31.3| fffffff0| -4.00
37.5| ffffffe8| -6.00
43.8| ffffffe8| -6.00
50.0| ffffffe8| -6.00
56.3| ffffffe8| -6.00
62.5| fffffff0| -4.00
68.8| fffffff0| -4.00
75.0| 00| 0.00
81.3| 00| 0.00
87.5| 00| 0.00
93.8| 00| 0.00
100.0| 00| 0.00

NAME: filtq_smoke_boi_rat1 ADDR: 22C3 UNT: "" OWN: B CODE: fltscb


EQN: E*4
BOI offset due to filt final tq when in smoke mode
%_Torque| HEX| ""
--------------------------------
0.0| 1c| 7.00
6.3| 08| 2.00
12.5| 08| 2.00
18.8| 04| 1.00
25.0| 00| 0.00
31.3| 00| 0.00
37.5| 00| 0.00
43.8| 00| 0.00
50.0| 00| 0.00
56.3| 00| 0.00
62.5| 00| 0.00
68.8| 00| 0.00
75.0| 00| 0.00
81.3| 00| 0.00
87.5| 00| 0.00
93.8| 00| 0.00
100.0| 00| 0.00

NAME: requested_torque_rat1 ADDR: 22D4 UNT: "" OWN: B CODE: rtqif


EQN: E*2.55
Rating 1 Requested Torque Table f(RPM,%throttle)
Table of AXIS_%_Throttle_9
%_Throttle ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.00 39.22 39.22 39.22 39.22 39.22
39.22 39.22 39.22
X 300.0 | 0.00 30.98 39.22 39.22 39.22 39.22
39.22 39.22 39.22
I 450.0 | 0.00 20.78 39.61 39.61 39.61 39.61
39.61 39.61 39.61
S 600.0 | 0.00 15.69 30.98 40.00 40.00 40.00
40.00 40.00 40.00
_ 750.0 | 0.00 12.55 24.71 37.25 52.94 52.94
52.94 52.94 52.94
R 900.0 | 0.00 10.20 20.78 30.98 56.08 65.88
65.88 65.88 65.88
P 1050.0 | 0.00 9.02 17.65 26.67 47.84 69.41
78.82 78.82 78.82
M 1200.0 | 0.00 7.84 15.69 23.14 41.96 60.78
79.22 92.16 92.16
_ 1350.0 | 0.00 7.06 13.73 20.78 37.25 53.73
70.59 87.06 92.55
1 1500.0 | 0.00 6.27 12.55 18.82 33.73 51.76
69.41 87.45 93.33
7 1650.0 | 0.00 5.49 11.37 16.86 30.59 47.45
64.71 81.57 87.06
1800.0 | 0.00 5.10 10.20 15.69 27.84 43.92
60.00 75.69 81.18
1950.0 | 0.00 4.71 9.41 14.51 25.88 40.78
55.29 70.20 75.29
2100.0 | 0.00 4.31 9.02 13.33 23.92 36.47
48.63 61.18 65.10
2250.0 | 0.00 4.31 8.24 12.55 22.35 32.16
41.96 51.76 54.90
2400.0 | 0.00 3.92 7.84 11.76 20.00 20.00
20.00 20.00 20.00
2550.0 | 0.00 3.53 7.45 10.98 19.61 19.61
20.00 20.00 20.00

Table of Hex Values


%_Throttle ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 64 64 64 64 64
64 64 64
X 300.0 | 00 4f 64 64 64 64
64 64 64
I 450.0 | 00 35 65 65 65 65
65 65 65
S 600.0 | 00 28 4f 66 66 66
66 66 66
_ 750.0 | 00 20 3f 5f 87 87
87 87 87
R 900.0 | 00 1a 35 4f 8f a8
a8 a8 a8
P 1050.0 | 00 17 2d 44 7a b1
c9 c9 c9
M 1200.0 | 00 14 28 3b 6b 9b
ca eb eb
_ 1350.0 | 00 12 23 35 5f 89
b4 de ec
1 1500.0 | 00 10 20 30 56 84
b1 df ee
7 1650.0 | 00 0e 1d 2b 4e 79
a5 d0 de
1800.0 | 00 0d 1a 28 47 70
99 c1 cf
1950.0 | 00 0c 18 25 42 68
8d b3 c0
2100.0 | 00 0b 17 22 3d 5d
7c 9c a6
2250.0 | 00 0b 15 20 39 52
6b 84 8c
2400.0 | 00 0a 14 1e 33 33
33 33 33
2550.0 | 00 09 13 1c 32 32
33 33 33

NAME: smoke_control_boi_rat1 ADDR: 236D UNT: "" OWN: B CODE: scboi


EQN: E*8
smoke_control_boi_rat1
RPM| HEX| ""
--------------------------------
150.0| 38| 7.00
300.0| 38| 7.00
450.0| 38| 7.00
600.0| 38| 7.00
750.0| 38| 7.00
900.0| 38| 7.00
1050.0| 38| 7.00
1200.0| 38| 7.00
1350.0| 38| 7.00
1500.0| 30| 6.00
1650.0| 30| 6.00
1800.0| 30| 6.00
1950.0| 30| 6.00
2100.0| 30| 6.00
2250.0| 30| 6.00
2400.0| 30| 6.00
2550.0| 30| 6.00

NAME: smoke_limiting_torque_rat1 ADDR: 237E UNT: "" OWN: B CODE: sctorq


EQN: E*2.55
smoke control TORQUE Table rating1 f(RPM,boost)

Table of AXIS_derived_smoke_control_9
derived_smoke_control ->
14.0 84.3 94.6 106.5 121.2 139.5
159.2 179.9 221.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 71.76 71.76 71.76 71.76 71.76 71.76
71.76 71.76 71.76
X 300.0 | 71.76 71.76 71.76 71.76 71.76 71.76
71.76 71.76 71.76
I 450.0 | 33.33 33.33 35.69 38.82 43.92 43.92
43.92 43.92 43.92
S 600.0 | 39.61 39.61 39.61 43.14 45.10 50.20
50.20 50.20 50.20
_ 750.0 | 40.00 40.00 40.00 49.02 54.12 58.04
60.00 61.96 65.10
R 900.0 | 41.96 41.96 43.92 52.94 56.86 61.96
76.08 87.06 100.00
P 1050.0 | 43.53 43.53 45.10 54.12 56.86 65.88
72.94 89.80 100.00
M 1200.0 | 45.10 45.10 45.10 54.12 56.86 66.27
73.73 90.98 100.00
_ 1350.0 | 45.10 45.10 45.10 52.55 58.43 65.49
80.78 90.98 100.00
1 1500.0 | 45.88 45.88 45.88 53.73 59.22 65.88
77.25 90.98 100.00
7 1650.0 | 47.06 47.06 47.06 52.94 58.04 67.06
78.82 92.16 100.00
1800.0 | 47.84 47.84 47.84 54.12 58.04 67.84
78.82 90.98 100.00
1950.0 | 47.84 47.84 47.84 54.12 56.08 63.14
80.00 89.80 100.00
2100.0 | 48.63 47.84 47.84 54.90 56.08 63.92
80.00 89.80 100.00
2250.0 | 49.02 49.02 43.14 56.47 60.00 67.84
79.61 89.80 100.00
2400.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
2550.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00

Table of Hex Values


derived_smoke_control ->
14.0 84.3 94.6 106.5 121.2 139.5
159.2 179.9 221.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | b7 b7 b7 b7 b7 b7
b7 b7 b7
X 300.0 | b7 b7 b7 b7 b7 b7
b7 b7 b7
I 450.0 | 55 55 5b 63 70 70
70 70 70
S 600.0 | 65 65 65 6e 73 80
80 80 80
_ 750.0 | 66 66 66 7d 8a 94
99 9e a6
R 900.0 | 6b 6b 70 87 91 9e
c2 de ff
P 1050.0 | 6f 6f 73 8a 91 a8
ba e5 ff
M 1200.0 | 73 73 73 8a 91 a9
bc e8 ff
_ 1350.0 | 73 73 73 86 95 a7
ce e8 ff
1 1500.0 | 75 75 75 89 97 a8
c5 e8 ff
7 1650.0 | 78 78 78 87 94 ab
c9 eb ff
1800.0 | 7a 7a 7a 8a 94 ad
c9 e8 ff
1950.0 | 7a 7a 7a 8a 8f a1
cc e5 ff
2100.0 | 7c 7a 7a 8c 8f a3
cc e5 ff
2250.0 | 7d 7d 6e 90 99 ad
cb e5 ff
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: torque_adjustment_rat1 ADDR: 2417 UNT: "" OWN: B CODE: tqadj


EQN: E*1024
Correct PW Tbl TRQ for BOI rtg1: TRQ=TRQ*(1+tqadj)
RPM| HEX| ""
--------------------------------
150.0| 00| 0.0000
300.0| 00| 0.0000
450.0| 00| 0.0000
600.0| 29| 0.0400
750.0| 29| 0.0400
900.0| 1d| 0.0283
1050.0| 12| 0.0176
1200.0| 1f| 0.0303
1350.0| 0e| 0.0137
1500.0| 17| 0.0225
1650.0| 17| 0.0225
1800.0| 24| 0.0352
1950.0| 17| 0.0225
2100.0| 14| 0.0195
2250.0| 00| 0.0000
2400.0| 00| 0.0000
2550.0| 00| 0.0000

NAME: torque_ss_rat1 ADDR: 2428 UNT: "" OWN: B CODE: sstqrd


EQN: E*2048
steady state TQ reduction due to BOI
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00000
300.0| 00| 0.00000
450.0| 00| 0.00000
600.0| 0e| 0.00684
750.0| 06| 0.00293
900.0| 03| 0.00146
1050.0| fffffffe| -0.00098
1200.0| fffffff8| -0.00391
1350.0| fffffff3| -0.00635
1500.0| fffffff2| -0.00684
1650.0| fffffff2| -0.00684
1800.0| ffffffee| -0.00879
1950.0| ffffffed| -0.00928
2100.0| fffffffe| -0.00098
2250.0| 00| 0.00000
2400.0| 00| 0.00000
2550.0| 00| 0.00000

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
rating_version_number_rat1 2439 102.0 DEC 66 E B
ratver Rating 1 Base Calibration Version No. for ID only

NAME: boi_table_rat1 ADDR: 243A UNT: "" OWN: B CODE: boifnc


EQN: E*8
BOI table rating 1 - function RPM and %load

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 6.00 6.00 6.00 6.00 6.00 6.00
6.00 6.00 6.00
X 300.0 | 6.00 6.00 6.00 6.00 6.00 6.00
6.00 6.00 6.00
I 450.0 | 3.00 3.00 3.00 4.00 4.00 4.00
4.00 4.00 6.00
S 600.0 | 3.00 3.00 3.00 4.00 4.00 4.00
4.00 4.00 6.00
_ 750.0 | 3.00 3.00 3.00 4.00 4.00 4.00
4.00 4.00 6.00
R 900.0 | 8.00 8.00 8.00 6.00 6.00 6.00
6.00 6.00 6.00
P 1050.0 | 8.00 8.00 6.00 4.00 4.00 4.00
6.00 6.00 7.00
M 1200.0 | 8.00 8.00 6.00 4.00 4.00 4.00
7.00 7.00 8.00
_ 1350.0 | 8.00 8.00 6.00 6.00 6.00 6.00
8.00 8.00 7.50
1 1500.0 | 8.00 8.00 6.00 2.50 1.00 1.00
1.00 1.00 6.00
7 1650.0 | 8.00 6.00 4.00 2.50 1.00 1.00
1.00 1.00 6.00
1800.0 | 8.00 6.00 4.00 2.50 0.00 0.00
0.00 0.00 7.00
1950.0 | 8.00 6.00 4.00 2.50 0.00 0.00
0.00 0.00 7.00
2100.0 | 8.00 6.00 4.00 2.50 0.00 0.00
0.00 0.00 6.00
2250.0 | 8.00 6.00 4.00 2.50 0.00 0.00
0.00 0.00 6.00
2400.0 | 9.00 9.00 6.00 4.00 4.00 4.00
4.00 4.00 6.00
2550.0 | 9.00 9.00 6.00 8.00 8.00 8.00
8.00 8.00 4.00
Table of Hex Values
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 30 30 30 30 30 30
30 30 30
X 300.0 | 30 30 30 30 30 30
30 30 30
I 450.0 | 18 18 18 20 20 20
20 20 30
S 600.0 | 18 18 18 20 20 20
20 20 30
_ 750.0 | 18 18 18 20 20 20
20 20 30
R 900.0 | 40 40 40 30 30 30
30 30 30
P 1050.0 | 40 40 30 20 20 20
30 30 38
M 1200.0 | 40 40 30 20 20 20
38 38 40
_ 1350.0 | 40 40 30 30 30 30
40 40 3c
1 1500.0 | 40 40 30 14 08 08
08 08 30
7 1650.0 | 40 30 20 14 08 08
08 08 30
1800.0 | 40 30 20 14 00 00
00 00 38
1950.0 | 40 30 20 14 00 00
00 00 38
2100.0 | 40 30 20 14 00 00
00 00 30
2250.0 | 40 30 20 14 00 00
00 00 30
2400.0 | 48 48 30 20 20 20
20 20 30
2550.0 | 48 48 30 40 40 40
40 40 20

NAME: boi_ss_rat1 ADDR: 24D3 UNT: "" OWN: B CODE: boissr


EQN: E*8
BOI table rating 1 for steady state

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 12.00 12.00 12.00 12.00 12.00 12.00
12.00 12.00 12.00
X 300.0 | 12.00 12.00 12.00 12.00 12.00 12.00
12.00 12.00 12.00
I 450.0 | 10.00 10.00 10.00 12.00 12.00 12.00
12.00 12.00 12.00
S 600.0 | 10.00 10.00 10.00 12.00 12.00 12.00
12.00 12.00 12.00
_ 750.0 | 10.00 10.00 10.00 15.00 15.00 15.00
15.00 15.00 15.00
R 900.0 | 15.00 15.00 14.00 14.00 16.00 16.00
16.00 16.00 16.00
P 1050.0 | 15.00 15.00 8.00 8.00 8.00 8.00
8.00 8.00 9.00
M 1200.0 | 15.00 15.00 7.00 7.00 7.00 8.00
8.00 8.00 11.00
_ 1350.0 | 15.00 15.00 8.00 9.50 10.00 10.00
10.00 10.50 11.25
1 1500.0 | 15.00 15.00 9.25 10.00 11.00 11.00
11.00 11.00 12.00
7 1650.0 | 15.00 15.00 9.25 10.00 11.00 11.00
11.00 11.00 12.00
1800.0 | 15.00 15.00 8.00 7.00 8.00 8.00
8.00 8.00 12.00
1950.0 | 15.00 15.00 10.00 7.00 7.00 8.00
8.00 8.00 12.00
2100.0 | 15.00 15.00 12.00 10.00 10.00 10.00
10.00 10.00 12.00
2250.0 | 15.00 15.00 12.00 10.00 10.00 10.00
10.00 10.00 12.00
2400.0 | 31.88 31.88 31.88 31.88 31.88 31.88
31.88 31.88 31.88
2550.0 | 31.88 31.88 31.88 31.88 31.88 31.88
31.88 31.88 31.88

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 60 60 60 60 60 60
60 60 60
X 300.0 | 60 60 60 60 60 60
60 60 60
I 450.0 | 50 50 50 60 60 60
60 60 60
S 600.0 | 50 50 50 60 60 60
60 60 60
_ 750.0 | 50 50 50 78 78 78
78 78 78
R 900.0 | 78 78 70 70 80 80
80 80 80
P 1050.0 | 78 78 40 40 40 40
40 40 48
M 1200.0 | 78 78 38 38 38 40
40 40 58
_ 1350.0 | 78 78 40 4c 50 50
50 54 5a
1 1500.0 | 78 78 4a 50 58 58
58 58 60
7 1650.0 | 78 78 4a 50 58 58
58 58 60
1800.0 | 78 78 40 38 40 40
40 40 60
1950.0 | 78 78 50 38 38 40
40 40 60
2100.0 | 78 78 60 50 50 50
50 50 60
2250.0 | 78 78 60 50 50 50
50 50 60
2400.0 | ff ff ff ff ff ff
ff ff ff
2550.0 | ff ff ff ff ff ff
ff ff ff

NAME: split_pilot_boi_offset_rat1 ADDR: 256C UNT: "" OWN: B CODE:


eppboi EQN: E*8
BOIpilot = min(absboi, BOI+eppboi)
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00
300.0| 00| 0.00
450.0| 00| 0.00
600.0| 00| 0.00
750.0| 00| 0.00
900.0| 00| 0.00
1050.0| 00| 0.00
1200.0| 00| 0.00
1350.0| 00| 0.00
1500.0| 00| 0.00
1650.0| 00| 0.00
1800.0| 00| 0.00
1950.0| 00| 0.00
2100.0| 00| 0.00
2250.0| 00| 0.00
2400.0| 00| 0.00
2550.0| 00| 0.00

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
checksum_rat2 257E 10141.0 HEX 279d E C
# Filled by Cal Tools
fuel_type_rat2 2580 95.0 DEC 5f E C
fuelrt Fueltp = 95 for diesel and Fueltp = 160 for gas
rating_edit_version_rat2 2581 29.0 "" 1d E C
rrlvrr rating_edit_version_rat2

NAME: filtq_smoke_torque_rat2 ADDR: 2582 UNT: "" OWN: B CODE: fltsmt


EQN: E*20.47
smoke torqe limit offset due to filt final tq
%_Torque| HEX| ""
--------------------------------
0.0| ffffff5c| -8.012
6.3| ffffff85| -6.009
12.5| ffffff9a| -4.983
18.8| ffffffae| -4.006
25.0| ffffffc3| -2.980
31.3| ffffffd7| -2.003
37.5| 0000| 0.000
43.8| 0000| 0.000
50.0| 0000| 0.000
56.3| 0000| 0.000
62.5| 0000| 0.000
68.8| 0000| 0.000
75.0| 0000| 0.000
81.3| 0000| 0.000
87.5| 0000| 0.000
93.8| 0000| 0.000
100.0| 0000| 0.000

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
actual_peak_torque_value_rat2 25A4 1550.0 FT# 060e E B
peaktq Rating 2 Peak Torque in foot*lbs
peak_torque_rpm_rat2 25A6 1200.00 RPM 12c0 E*4 B
ptqrpm RPM at which engine delivers peak torque for rtg2
rated_horse_power_rat2 25A8 370.0 BHP 0172 E B
ratbhp rated brake horsepower for rating 2
rated_max_rpm_rat2 25AA 2110.00 RPM 20f8 E*4 B
ratrpm rated engine RPM for rating 2

NAME: boi_torque_reduction_rat2 ADDR: 25AC UNT: "" OWN: B CODE: rpmtqc


EQN: E*2048
%TQ redux/deg BOI advance from adaptv or temp-rat2
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00000
300.0| 00| 0.00000
450.0| 00| 0.00000
600.0| 0a| 0.00488
750.0| 06| 0.00293
900.0| 04| 0.00195
1050.0| 00| 0.00000
1200.0| fffffffc| -0.00195
1350.0| fffffff7| -0.00439
1500.0| fffffff4| -0.00586
1650.0| fffffff3| -0.00635
1800.0| fffffff6| -0.00488
1950.0| fffffff8| -0.00391
2100.0| ffffffff| -0.00049
2250.0| 00| 0.00000
2400.0| 00| 0.00000
2550.0| 00| 0.00000

NAME: base_air_temp_offset_boi_rat2 ADDR: 25BD UNT: "" OWN: B CODE:


basboi EQN: E*4
delta BOI as a f(air temperature)
dgC| HEX| ""
--------------------------------
-40.0| 00| 0.00
-27.8| 00| 0.00
-15.6| 00| 0.00
-3.3| 00| 0.00
8.9| 00| 0.00
21.1| 00| 0.00
33.3| 00| 0.00
45.6| 00| 0.00
57.8| 00| 0.00
70.0| 00| 0.00
82.2| 00| 0.00
94.4| 00| 0.00
106.7| 00| 0.00
118.9| 00| 0.00
131.1| 00| 0.00
143.3| 00| 0.00
155.6| 00| 0.00

NAME: filtq_offset_boi_rat2 ADDR: 25CE UNT: "" OWN: B CODE: fltboi


EQN: E*4
BOI offset due to filt final tq
%_Torque| HEX| ""
--------------------------------
0.0| 00| 0.00
6.3| 00| 0.00
12.5| fffffffc| -1.00
18.8| fffffff8| -2.00
25.0| fffffff4| -3.00
31.3| fffffff0| -4.00
37.5| ffffffe8| -6.00
43.8| ffffffe8| -6.00
50.0| ffffffe8| -6.00
56.3| ffffffe8| -6.00
62.5| fffffff0| -4.00
68.8| fffffff0| -4.00
75.0| 00| 0.00
81.3| 00| 0.00
87.5| 00| 0.00
93.8| 00| 0.00
100.0| 00| 0.00

NAME: filtq_smoke_boi_rat2 ADDR: 25DF UNT: "" OWN: B CODE: fltscb


EQN: E*4
BOI offset due to filt final tq when in smoke mode
%_Torque| HEX| ""
--------------------------------
0.0| 1c| 7.00
6.3| 08| 2.00
12.5| 08| 2.00
18.8| 04| 1.00
25.0| 00| 0.00
31.3| 00| 0.00
37.5| 00| 0.00
43.8| 00| 0.00
50.0| 00| 0.00
56.3| 00| 0.00
62.5| 00| 0.00
68.8| 00| 0.00
75.0| 00| 0.00
81.3| 00| 0.00
87.5| 00| 0.00
93.8| 00| 0.00
100.0| 00| 0.00

NAME: requested_torque_rat2 ADDR: 25F0 UNT: "" OWN: B CODE: rtqif


EQN: E*2.55
Rating 2 Requested Torque Table f(RPM,%throttle)

Table of AXIS_%_Throttle_9
%_Throttle ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 0.00 39.22 39.22 39.22 39.22 39.22
39.22 39.22 39.22
X 300.0 | 0.00 30.98 39.22 39.22 39.22 39.22
39.22 39.22 39.22
I 450.0 | 0.00 20.78 39.61 39.61 39.61 39.61
39.61 39.61 39.61
S 600.0 | 0.00 15.69 30.98 40.00 40.00 40.00
40.00 40.00 40.00
_ 750.0 | 0.00 12.55 24.71 37.25 52.94 52.94
52.94 52.94 52.94
R 900.0 | 0.00 10.20 20.78 30.98 56.08 65.88
65.88 65.88 65.88
P 1050.0 | 0.00 9.02 17.65 26.67 47.84 69.41
78.82 78.82 78.82
M 1200.0 | 0.00 7.84 15.69 23.14 41.96 60.78
79.22 92.16 92.16
_ 1350.0 | 0.00 7.06 13.73 20.78 37.25 53.73
70.59 87.06 92.55
1 1500.0 | 0.00 6.27 12.55 18.82 33.73 51.76
69.41 87.45 93.33
7 1650.0 | 0.00 5.49 11.37 16.86 30.59 47.45
64.71 81.57 87.45
1800.0 | 0.00 5.10 10.20 15.69 27.84 43.92
60.00 76.08 81.18
1950.0 | 0.00 4.71 9.41 14.51 25.88 40.78
55.69 70.20 75.29
2100.0 | 0.00 4.31 9.02 13.33 23.92 34.90
46.27 57.25 61.18
2250.0 | 0.00 4.31 8.24 12.55 22.35 29.41
36.47 43.53 45.88
2400.0 | 0.00 3.92 7.84 11.76 20.00 20.00
20.00 20.00 20.00
2550.0 | 0.00 3.53 7.45 10.98 19.61 19.61
20.00 20.00 20.00

Table of Hex Values


%_Throttle ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 00 64 64 64 64 64
64 64 64
X 300.0 | 00 4f 64 64 64 64
64 64 64
I 450.0 | 00 35 65 65 65 65
65 65 65
S 600.0 | 00 28 4f 66 66 66
66 66 66
_ 750.0 | 00 20 3f 5f 87 87
87 87 87
R 900.0 | 00 1a 35 4f 8f a8
a8 a8 a8
P 1050.0 | 00 17 2d 44 7a b1
c9 c9 c9
M 1200.0 | 00 14 28 3b 6b 9b
ca eb eb
_ 1350.0 | 00 12 23 35 5f 89
b4 de ec
1 1500.0 | 00 10 20 30 56 84
b1 df ee
7 1650.0 | 00 0e 1d 2b 4e 79
a5 d0 df
1800.0 | 00 0d 1a 28 47 70
99 c2 cf
1950.0 | 00 0c 18 25 42 68
8e b3 c0
2100.0 | 00 0b 17 22 3d 59
76 92 9c
2250.0 | 00 0b 15 20 39 4b
5d 6f 75
2400.0 | 00 0a 14 1e 33 33
33 33 33
2550.0 | 00 09 13 1c 32 32
33 33 33

NAME: smoke_control_boi_rat2 ADDR: 2689 UNT: "" OWN: B CODE: scboi


EQN: E*8
smoke_control_boi_rat2
RPM| HEX| ""
--------------------------------
150.0| 38| 7.00
300.0| 38| 7.00
450.0| 38| 7.00
600.0| 38| 7.00
750.0| 38| 7.00
900.0| 38| 7.00
1050.0| 38| 7.00
1200.0| 38| 7.00
1350.0| 38| 7.00
1500.0| 30| 6.00
1650.0| 30| 6.00
1800.0| 30| 6.00
1950.0| 30| 6.00
2100.0| 30| 6.00
2250.0| 30| 6.00
2400.0| 30| 6.00
2550.0| 30| 6.00

NAME: smoke_limiting_torque_rat2 ADDR: 269A UNT: "" OWN: B CODE: sctorq


EQN: E*2.55
smoke control TORQUE Table rating2 f(RPM,boost)

Table of AXIS_derived_smoke_control_9
derived_smoke_control ->
14.0 84.3 94.6 106.5 121.2 139.5
159.2 179.9 221.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 71.76 71.76 71.76 71.76 71.76 71.76
71.76 71.76 71.76
X 300.0 | 71.76 71.76 71.76 71.76 71.76 71.76
71.76 71.76 71.76
I 450.0 | 33.33 33.33 35.69 38.82 43.92 43.92
43.92 43.92 43.92
S 600.0 | 39.61 39.61 39.61 43.14 45.10 50.20
50.20 50.20 50.20
_ 750.0 | 40.00 40.00 40.00 49.02 54.12 58.04
60.00 61.96 65.10
R 900.0 | 41.96 41.96 43.92 52.94 56.86 61.96
76.08 87.06 100.00
P 1050.0 | 43.53 43.53 45.10 54.12 56.86 65.88
72.94 89.80 100.00
M 1200.0 | 45.10 45.10 45.10 54.12 56.86 66.27
73.73 90.98 100.00
_ 1350.0 | 45.10 45.10 45.10 52.55 58.43 65.49
80.78 90.98 100.00
1 1500.0 | 45.88 45.88 45.88 53.73 59.22 65.88
77.25 90.98 100.00
7 1650.0 | 47.06 47.06 47.06 52.94 58.04 67.06
78.82 92.16 100.00
1800.0 | 47.84 47.84 47.84 54.12 58.04 67.84
78.82 90.98 100.00
1950.0 | 47.84 47.84 47.84 54.12 56.08 63.14
80.00 89.80 100.00
2100.0 | 48.63 47.84 47.84 54.90 56.08 63.92
80.00 89.80 100.00
2250.0 | 49.02 49.02 43.14 56.47 60.00 67.84
79.61 89.80 100.00
2400.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00
2550.0 | 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00

Table of Hex Values


derived_smoke_control ->
14.0 84.3 94.6 106.5 121.2 139.5
159.2 179.9 221.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | b7 b7 b7 b7 b7 b7
b7 b7 b7
X 300.0 | b7 b7 b7 b7 b7 b7
b7 b7 b7
I 450.0 | 55 55 5b 63 70 70
70 70 70
S 600.0 | 65 65 65 6e 73 80
80 80 80
_ 750.0 | 66 66 66 7d 8a 94
99 9e a6
R 900.0 | 6b 6b 70 87 91 9e
c2 de ff
P 1050.0 | 6f 6f 73 8a 91 a8
ba e5 ff
M 1200.0 | 73 73 73 8a 91 a9
bc e8 ff
_ 1350.0 | 73 73 73 86 95 a7
ce e8 ff
1 1500.0 | 75 75 75 89 97 a8
c5 e8 ff
7 1650.0 | 78 78 78 87 94 ab
c9 eb ff
1800.0 | 7a 7a 7a 8a 94 ad
c9 e8 ff
1950.0 | 7a 7a 7a 8a 8f a1
cc e5 ff
2100.0 | 7c 7a 7a 8c 8f a3
cc e5 ff
2250.0 | 7d 7d 6e 90 99 ad
cb e5 ff
2400.0 | 00 00 00 00 00 00
00 00 00
2550.0 | 00 00 00 00 00 00
00 00 00

NAME: torque_adjustment_rat2 ADDR: 2733 UNT: "" OWN: B CODE: tqadj


EQN: E*1024
Correct PW Tbl TRQ for BOI rtg2: TRQ=TRQ*(1+tqadj)
RPM| HEX| ""
--------------------------------
150.0| 00| 0.0000
300.0| 00| 0.0000
450.0| 00| 0.0000
600.0| 29| 0.0400
750.0| 29| 0.0400
900.0| 1d| 0.0283
1050.0| 12| 0.0176
1200.0| 1f| 0.0303
1350.0| 0e| 0.0137
1500.0| 17| 0.0225
1650.0| 17| 0.0225
1800.0| 24| 0.0352
1950.0| 17| 0.0225
2100.0| 0f| 0.0146
2250.0| 00| 0.0000
2400.0| 00| 0.0000
2550.0| 00| 0.0000

NAME: torque_ss_rat2 ADDR: 2744 UNT: "" OWN: B CODE: sstqrd


EQN: E*2048
steady state TQ reduction due to BOI
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00000
300.0| 00| 0.00000
450.0| 00| 0.00000
600.0| 0e| 0.00684
750.0| 06| 0.00293
900.0| 03| 0.00146
1050.0| fffffffe| -0.00098
1200.0| fffffff8| -0.00391
1350.0| fffffff3| -0.00635
1500.0| fffffff2| -0.00684
1650.0| fffffff2| -0.00684
1800.0| ffffffee| -0.00879
1950.0| ffffffed| -0.00928
2100.0| ffffffe4| -0.01367
2250.0| 00| 0.00000
2400.0| 00| 0.00000
2550.0| 00| 0.00000

NAME ADDR ENG. VAL UNT HEX EQUATION


OWN CODE COMMENT
rating_version_number_rat2 2755 101.0 DEC 65 E B
ratver Rating 2 Base Calibration Version No. for ID only

NAME: boi_table_rat2 ADDR: 2756 UNT: "" OWN: B CODE: boifnc


EQN: E*8
BOI table rating 2 - function RPM and %load

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 6.00 6.00 6.00 6.00 6.00 6.00
6.00 6.00 6.00
X 300.0 | 6.00 6.00 6.00 6.00 6.00 6.00
6.00 6.00 6.00
I 450.0 | 3.00 3.00 3.00 4.00 4.00 4.00
4.00 4.00 6.00
S 600.0 | 3.00 3.00 3.00 4.00 4.00 4.00
4.00 4.00 6.00
_ 750.0 | 3.00 3.00 3.00 4.00 4.00 4.00
4.00 4.00 4.00
R 900.0 | 8.00 8.00 8.00 6.00 6.00 6.00
6.00 6.00 5.00
P 1050.0 | 8.00 8.00 6.00 4.00 4.00 4.00
6.00 6.00 6.00
M 1200.0 | 8.00 8.00 6.00 4.00 4.00 4.00
7.00 7.00 7.00
_ 1350.0 | 8.00 8.00 6.00 6.00 6.00 6.00
8.00 8.00 7.00
1 1500.0 | 8.00 8.00 6.00 2.50 1.00 1.00
1.00 1.00 6.00
7 1650.0 | 8.00 6.00 4.00 2.50 1.00 1.00
1.00 1.00 6.00
1800.0 | 8.00 6.00 4.00 2.50 0.00 0.00
0.00 0.00 7.00
1950.0 | 8.00 6.00 4.00 2.50 0.00 0.00
0.00 0.00 7.00
2100.0 | 8.00 6.00 4.00 2.50 0.00 0.00
0.00 0.00 7.00
2250.0 | 8.00 6.00 4.00 2.50 0.00 0.00
0.00 0.00 7.00
2400.0 | 9.00 9.00 6.00 4.00 4.00 4.00
4.00 4.00 7.00
2550.0 | 9.00 9.00 6.00 8.00 8.00 8.00
8.00 8.00 4.00

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 30 30 30 30 30 30
30 30 30
X 300.0 | 30 30 30 30 30 30
30 30 30
I 450.0 | 18 18 18 20 20 20
20 20 30
S 600.0 | 18 18 18 20 20 20
20 20 30
_ 750.0 | 18 18 18 20 20 20
20 20 20
R 900.0 | 40 40 40 30 30 30
30 30 28
P 1050.0 | 40 40 30 20 20 20
30 30 30
M 1200.0 | 40 40 30 20 20 20
38 38 38
_ 1350.0 | 40 40 30 30 30 30
40 40 38
1 1500.0 | 40 40 30 14 08 08
08 08 30
7 1650.0 | 40 30 20 14 08 08
08 08 30
1800.0 | 40 30 20 14 00 00
00 00 38
1950.0 | 40 30 20 14 00 00
00 00 38
2100.0 | 40 30 20 14 00 00
00 00 38
2250.0 | 40 30 20 14 00 00
00 00 38
2400.0 | 48 48 30 20 20 20
20 20 38
2550.0 | 48 48 30 40 40 40
40 40 20

NAME: boi_ss_rat2 ADDR: 27EF UNT: "" OWN: B CODE: boissr


EQN: E*8
BOI table rating 2 for steady state

Table of AXIS_%_Load_9
%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 12.00 12.00 12.00 12.00 12.00 12.00
12.00 12.00 12.00
X 300.0 | 12.00 12.00 12.00 12.00 12.00 12.00
12.00 12.00 12.00
I 450.0 | 10.00 10.00 10.00 12.00 12.00 12.00
12.00 12.00 12.00
S 600.0 | 10.00 10.00 10.00 12.00 12.00 12.00
12.00 12.00 12.00
_ 750.0 | 10.00 10.00 10.00 15.00 15.00 15.00
15.00 15.00 15.00
R 900.0 | 15.00 15.00 12.00 12.00 16.00 16.00
16.00 16.00 16.00
P 1050.0 | 15.00 15.00 8.00 8.00 8.00 8.00
8.00 8.00 9.00
M 1200.0 | 15.00 15.00 7.00 7.00 7.00 8.00
8.00 8.00 11.00
_ 1350.0 | 15.00 15.00 8.00 9.50 10.00 10.00
10.00 10.50 11.50
1 1500.0 | 15.00 15.00 9.25 10.00 11.00 11.00
11.00 11.00 12.00
7 1650.0 | 15.00 15.00 9.25 10.00 11.00 11.00
11.00 11.00 12.00
1800.0 | 15.00 15.00 8.00 7.00 8.00 8.00
8.00 8.00 12.00
1950.0 | 15.00 15.00 10.00 7.00 7.00 8.00
8.00 8.00 11.00
2100.0 | 15.00 15.00 12.00 10.00 10.00 10.00
10.00 10.00 12.00
2250.0 | 15.00 15.00 12.00 10.00 10.00 10.00
10.00 10.00 12.00
2400.0 | 31.88 31.88 31.88 31.88 31.88 31.88
31.88 31.88 31.88
2550.0 | 31.88 31.88 31.88 31.88 31.88 31.88
31.88 31.88 31.88

Table of Hex Values


%_Load ->
0.0 12.5 25.0 37.5 50.0 62.5
75.0 87.5 100.0
-----------------------------------------------------------------------------------
----------------------------------
A 150.0 | 60 60 60 60 60 60
60 60 60
X 300.0 | 60 60 60 60 60 60
60 60 60
I 450.0 | 50 50 50 60 60 60
60 60 60
S 600.0 | 50 50 50 60 60 60
60 60 60
_ 750.0 | 50 50 50 78 78 78
78 78 78
R 900.0 | 78 78 60 60 80 80
80 80 80
P 1050.0 | 78 78 40 40 40 40
40 40 48
M 1200.0 | 78 78 38 38 38 40
40 40 58
_ 1350.0 | 78 78 40 4c 50 50
50 54 5c
1 1500.0 | 78 78 4a 50 58 58
58 58 60
7 1650.0 | 78 78 4a 50 58 58
58 58 60
1800.0 | 78 78 40 38 40 40
40 40 60
1950.0 | 78 78 50 38 38 40
40 40 58
2100.0 | 78 78 60 50 50 50
50 50 60
2250.0 | 78 78 60 50 50 50
50 50 60
2400.0 | ff ff ff ff ff ff
ff ff ff
2550.0 | ff ff ff ff ff ff
ff ff ff

NAME: split_pilot_boi_offset_rat2 ADDR: 2888 UNT: "" OWN: B CODE:


eppboi EQN: E*8
BOIpilot = min(absboi, BOI+eppboi)
RPM| HEX| ""
--------------------------------
150.0| 00| 0.00
300.0| 00| 0.00
450.0| 00| 0.00
600.0| 00| 0.00
750.0| 00| 0.00
900.0| 00| 0.00
1050.0| 00| 0.00
1200.0| 00| 0.00
1350.0| 00| 0.00
1500.0| 00| 0.00
1650.0| 00| 0.00
1800.0| 00| 0.00
1950.0| 00| 0.00
2100.0| 00| 0.00
2250.0| 00| 0.00
2400.0| 00| 0.00
2550.0| 00| 0.00

You might also like