Enrollment & Management Software User Manual V2.4.3.1037

Enrollment & Management Software
User Manual
Version: 2.4.3.1037
Date: November 2010
About This Manual

This document introduces the interface and menu operations of the
Enrollment & Management Software.
Table of Contents
Table of Contents
1. Function Overview .................................................................1
2. Installation Environment........................................................2
3. Install and Uninstall Software................................................3
3.1 Install Software................................................................................. 3
3.2 Uninstall Software ............................................................................ 7
4. User Management ..................................................................8
4.1 Add User .......................................................................................... 8
4.2 Modify Users Information ................................................................ 9
4.3 Department Management ...............................................................11
4.3.1 Add Department ....................................................................11
4.3.2 Modify Department............................................................... 12
4.3.3 Modify Department Relationship .......................................... 13
4.3.4 Delete Department ............................................................... 14
4.3.5 Add User to Department....................................................... 15
5. Device Management .............................................................19
5.1 Add Device ..................................................................................... 19
5.2 Enroll User Fingerprint ................................................................... 22
5.2.1 Fingerprint Sensor Enrollment ............................................. 22
5.2.2 Fingerprint Device Enrollment.............................................. 26
5.3 From Device to PC......................................................................... 26
5.4 From PC to Device......................................................................... 28
5.5 Device Information ......................................................................... 30
5.5.1 Device Information ............................................................... 30
5.5.2 Communication .................................................................... 31
5.5.3 Wiegand............................................................................... 32
5.5.4 Verification ........................................................................... 34
II
Enrollment & Management Software User Manual
5.5.5 Power Management ............................................................. 35

5.5.6 Access Control ..................................................................... 36
5.5.7 Mifare ................................................................................... 37
5.5.8 Other Setup.......................................................................... 37
5.5.9 U disk Settings ..................................................................... 39
6. System Management............................................................41
6.1 Operator Management ................................................................... 41
6.2 System Operation Log ................................................................... 45
6.3 Backup Database........................................................................... 46
6.4 Compact the Database .................................................................. 47
6.5 Clear Obsolete Data....................................................................... 47
6.6 Initialize System ............................................................................. 48
6.7 Set Database ................................................................................. 48
6.8 Set Password of Database............................................................. 51
7. Other Functions....................................................................52
7.1 Update Firmware............................................................................ 52
7.2 Restart Device................................................................................ 52
7.3 Property ......................................................................................... 53
8. Appendix ...............................................................................54
8.1 Connect with Device ...................................................................... 54
8.1.1 RS232 Mode ........................................................................ 54
8.1.2 RS485 Mode ........................................................................ 56
8.1.3 TCP/IP Mode........................................................................ 57
8.1.4 USB Mode............................................................................ 59
8.2 Fingerprint Algorithm License......................................................... 59
8.3 The toolbar for datasheet operation ............................................... 62
8.4 Date ............................................................................................... 63
8.5 Sort Order ...................................................................................... 64
8.6 Filtrate Data.................................................................................... 64
III
Table of Contents
8.7 Record Group and Statistics .......................................................... 66

9. End User Software License Agreement..............................68
IV
1. Function Overview
1. Function Overview
Enrollment & Management Software is mini independent management
software, and its easy for user to manipulate. It is mainly used to manage the
user data (user fingerprints and etc.) and the records.
Refer to the following for detailed functions:
Manage users basic information and records.
Set the operator password to ensure the system security.
Set the management function, read the device settings and set the
parameters.
Upload and download users information from the device.
Provide various database interfaces.
1
2. Installation Environment
2. Installation Environment
Computer
Above Pentium l 66, more than 64M memory, at least 100M hard disk
space is needed.
Operation system
Microsoft Windows 98 (Second Edition)
Microsoft Windows NT 4.0 (SP4 or Later Edition)
Microsoft Windows 2000
Microsoft Windows XP
Windows 2000 operation system and Pentium III 500, 128M memory is
recommended.
2
3. Install and Uninstall Software

3.1 Install Software
Before installing your software, it is better to shutdown all the other
application programs, in order to keep away conflict.
Note: The following picture may differ from what you see upon CD
installation. Please refer to the actual installation.
1. Please put the software CD into CD-ROM, it will run automatically and
popup the language selection dialog.
2. The system supports three languages, Simplified Chinese, Traditional
Chinese and English. Select the language, click [OK], and enter the following
interface.
Note: Press [Cancel] in this interface to stop the installation process.

3. Click [Next] in the system installation interface, start to install the
software.
3
4. Please read the License Agreement carefully. If you want to install it

please select [I accept the agreement], click [Next], and enter the following
interface.
5. Select the folder where to install the software. Click [Next] to enter the
following interface.
4
6. Select the component to install. Its recommended to select all

components, and then click [Next].
7. This interface is to confirm the shortcut which is created in [Start] ->

[Program] menu. Click [Next] button, display the following interface.
5
8. Click [Install], the installing program will copy and write corresponding
information into hard disk. When the installation completed, click [Finish] to
complete the process.
6
3.2 Uninstall Software

If you do not need to use this software any more, and want to uninstall it
from your computer, then you may follow the steps below.
1. Close all the application software complete.
2. Enter Start -> Setting -> Control panel.
3. Enter [Add or Remove Program] window, choose [Enrollment &
Management Software], and click [Remove] button to uninstall.
4. Like doing this, you still cannot delete all files. You need enter the
installation directory of the software to delete the folder where the software is
installed.
7
4. User Management
4. User Management
4.1 Add User
Operation Steps:
1. Enter the user management interface: Click [Basic Settings] -> [User
Management], or click [User Management] shortcut in the main interface.
2. Click + button to add new user, as the figure above. Select user
department (The new user belong to the department of [company] by default).
Input users number, name, card number (read through the card reader if its
available), select the user gender, privilege and so on.
3. Click button to select the users photo. Then the added users
information will be shown on the user management interface.
8
4. User Management
4. Click [Set Password] and input the same password twice.
5. Enroll the user fingerprint, for details please refer to 5.2 Enroll User
Fingerprint.
6. After editing, click to save, or click to cancel.
The new added user will display on the user management interface.
4.2 Modify Users Information

The user information can be input manually, or import from other
software. After importing, you can modify the information by this function.
9
Operation Steps:
1. In user management interface, select the user you want to modify,
click button to enter the edit state.
2. Modify the desired information. For example, change the user

privilege from [User] to [Enroller], as the following interface.
3. After editing, click to save, or click to cancel.
10
4. User Management
4.3 Department Management
4.3.1 Add Department

1. Enter [Department Management] interface: Click [Basic Settings] ->
[Department], as shown below:
2. Click [Add] button and enter the [Add New Department] interface, as
shown below:
3. Input the departments name, click [OK] to save, and the added new
department is displayed under the [company] name.
11
4. Add other departments as step 2-3, thus the department is added to

the list, as shown below:
4.3.2 Modify Department

1. Select the department which needs to modify and click it another time,
the department enter the edit state.
12
4. User Management
2. After modification, click other place to quit the edit state, as shown
below: [R&D] has been changed into [R&D Dept.].
4.3.3 Modify Department Relationship
1. Select the department which needs to modify.
13
2. Drag the department to the target position. Such as drag the

department [Test] to under the department of [R&D Dept.], as shown below.
Thus the department [Test] is a sub department of [R&D Dept.].
4.3.4 Delete Department

1. Select the department which needs to delete.
14
4. User Management
2. Click [Delete] button to popup the confirm message, as shown below.
3. Click [OK] to delete, otherwise click [Cancel] to cancel.
4.3.5 Add User to Department
All users are belonging to the department of [company] by default.
1. Firstly select the department of [company], then click [User] button,
popup the following interface.
15
2. Choose the user of company to shift, and then click the < button to
move the user to the left side, or click << button to move all users to the left
side.
3. Click [Close] to return to the department management interface. Click

the name of corresponding department, click [User] button, the following
interface appears.
16
4. User Management
4. Select the user and click > to move the user to the right side, or click
>> button to move all users to the right side to complete shifting the user.
5. Follow the steps 3-4, you can assign all users to corresponding
departments, after that, the user management interface is shown as below.
17
18
5. Device Management
5.1 Add Device
Function Introduction:
To achieve data upload & download and other functions, the software
needs to communicate with the device. You need only to add and save the
device communication parameters to the system during the first use.
1. Open [Device Management] in the [Basic Settings] menu, or click
[Device Management] shortcut on the main interface, and display the
interface as below.
2. Click [Add] button, display the following interface.

The system supports RS232/485, Ethernet and USB communication
modes. For details please refer to 8.1 Connect with Device.
19
3. After setting the parameters, click [Connect] to check the connection.
4. If it prompts [Failed in connecting with device], return to the step 2

to check the settings and connect again. If it prompts [Succeed in
connecting with device], the connection is done.
5. After connecting with the device, you can catch sight of the devices
icon shown on the main interface, as in the following picture.
20
6. The devices connecting parameters will be preserved in the system. If

you want to operate the device, you can just click this icon.
7. If you need to add other devices, follow the step 2-6.
21
5.2 Enroll User Fingerprint
5.2.1 Fingerprint Sensor Enrollment

1. Click [User Management] in [Basic Settings] menu, or click [User
Management] shortcut in the main interface, to enter the user management
interface. You can add a new user or select an enrolled user in user list to
modify his/her information. The add user operations please refer to 4.1 Add
User.
2. Select [Enroll with sensor], select 9.0 or 10.0 algorithm. For 10.0
algorithm version, you need to know if you have a fingerprint algorithm
license, for details please refer to 8.2 Fingerprint Algorithm License. Then
click [Enroll], and enter the fingerprint enrollment interface, as shown below.
22
3. Click the finger to be enrolled, and the system enters the enrollment
state, as shown below.
4. After the finger finishes its press on the fingerprint sensor, the system
enters the following state.
23
5. Press three times with the same finger according to the tips, if the
enrollment is succeed, the interface is as below.
6. Click [OK] after successful enrollment, save the fingerprint and return
to the previous interface.
7. Click [Verify], the following interface will appear to check if the
fingerprint enrollment is success or not.
24
8. Press the finger on the device. The enrollment succeeds if the

following dialogue appears.
9. Press the finger on the device, if the following dialogue appears, then
the enrollment failed, please return to step 3-6 for re-enrollment.
25
5.2.2 Fingerprint Device Enrollment
1. Click [User Management] in [Basic Settings] menu, or click [User

Management] shortcut in the main interface, to enter the user management
interface. You can add a new user or select an enrolled user in user list to
modify his/her information. The add user operations please refer to 4.1 Add
User.
2. Select the device and click [Connect Device] button to connect the
device.
3. After the connection is completed, the button turns to [Disconnect].
Click [Enroll] to enter fingerprint enrollment interface, the following process is
similar to fingerprint sensor enrollment, exclude the [Verify] operation.
5.3 From Device to PC

To facilitate the unity management of users, you can download the users
information and fingerprint data from the device to computer.
Operations are as follows:
1. In the user management interface, select [From device to PC]. Or
26
click [Device to PC] shortcut on the main interface, and display the following
interface.
2. Select the target device, and click [Browse Users in device], the
users in the device will list on the interface, as shown in the following picture.
New User: Displays the users in the device but not in the system.
3. Select a user in the user list or click the [Select all] button to select all
users.
27
4. Click [Download] to download user and fingerprint data. The system

will automatically preserve users information and fingerprint data to the
database. After downloading, the tick before user will be cleared
automatically, the downloaded user move to the left list.
5.4 From PC to Device

Function Introduction:
28
Upload users information and fingerprint data from the computer to

device. You can modify or delete the user information in the device by this
function.
Operation Steps:
1. In the user management interface, select [From PC to Device]. Or
click [PC to Device] shortcut on the main interface, and display the following
interface.
2. Select a user in the user list or click the [Select all] button to select all
users, and then click [Upload] to upload user and fingerprint data. You can
select Fingerprint, User Face or Cache mode before uploading, if no option
is selected only the user information will be uploaded.
3. Select the device in the device list or click the [Select all] button to
select all devices.
4. Right click to select the operation options.
Upload: Upload the selected user information to the selected device.
Before uploading, you need to confirm the uploading data, that include user
information and user fingerprint. User information includes user name, user
ID, password and etc. except the user fingerprint. User fingerprint indicate
29
fingerprint template of a specified user ID. If there are much data to upload,
you can select [Cache] mode to speed up.
Delete: If you want to delete a user from the device, firstly choose the
user and the corresponding device, and then click [Delete] button.
Operation Log: That is the error logs during the operating process.
5. After uploading succeeds, the operation information will display on the

lower side of the main interface.
5.5 Device Information
5.5.1 Device Information

Click [Device info] in the [Device Management], and click [Read
Options], the device information will be listed, as the following figure.
30
5.5.2 Communication
1. Click [Communication] in the [Device Management], and click
[Read Options], the communication information of the current connected
device will display, as the following figure.
2. If you want to change some communication parameters, modify it as

needed and click [Set Options] button, then restart the device to complete
31
the operation.
5.5.3 Wiegand
1. Click [Wiegand] in the [Device Management], and click [Read
Options] can obtain all the Wiegand parameters which store in the device.
Wiegand Setting includes Wiegand output and input settings.

Defined Format: These formats have been defined and built in the
system. You neednt to define the length of Bit and the location of information.
There are four default defined formats: Wiegand26 with device ID,
Wiegand34 with device ID, Wiegand26 without device ID, Wiegand34
without device ID.
The Wiegand 26 with device ID means that the Wiegand26 output
format along with device ID number.
The Wiegand26 without device ID means that the Wiegand26 output
format doesnt own the device ID.
Device ID is defined by following: If there is no site code, then it will
output device ID. And if the site code has been set, it will output the defined
site code (which is similar to the device ID, they are different that this code is
32
defined by user and can be used repeatedly, range is 0-255).

Fail ID: Export Fail ID after verification failure, nothing exports when it
has not being selected. Its output range is 0-65534.
Site Code: Similar to the device ID, the difference is that this code is
defined by user and can be used repeatedly in different unit, range is 0-255.
Input format: Assigns Wiegand inputs format, as the following detailed
introductions.
OEM code: Neednt to be defined for 26 bit-Wiegand generally, find it
from 37, 34 bit Wiegand.
Facility code: Refers to the device ID or site code.
ID Number: User ID number.
Use its first letter for respectively indicate (no matter it is in capital letter
or small letter) in the format. ofiOFI, the small letter refers to Odd, the capital
letter refers to Even, Oo refers to OEM code, Ff refers to Facility code, Ii is ID
number, P refers to the parity bit. The following is a demonstration with a
standard 26bit-Wiegand input: PFFFFFFFFIIIIiiiiiiiiiiiiP, Facility code and ID
Number are both 1:
E Facility code ID Number O
P F F F F F F F F I I I I i i i i i i i i i i i i P
1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
Total Bit: The length of output format.
Pulse Width Time: The default to send pulse width time is 100s; you
can adjust the value from 20 to 800.
Pulse Interval Time: The default value is 900 s. You can adjust it from
200 to 20000.
Input/Output contents: ID or Card No.
33
5.5.4 Verification
1. Click [Biometric] in the [Device Management], and click [Read
Options], the following interface displays.
2. You can modify the parameters as needed, to obtain the best

performance. After modification, click [Set Options] and restart the device,
and then the modification take effect.
Fingerprint 1: N Threshold: The default value is Middle, you can
modify it.
Fingerprint 1:1 Threshold: It indicates the fingerprint match threshold
in 1:1 verification. The default value is Middle.
Face 1: N threshold: The default value is Middle, you can modify it.
Face 1:1 threshold: It indicates the face match threshold in 1:1
verification, the default value is Middle.
Only 1:1 Match: This feature is only available when a user own
fingerprint, ID card or Mifare card for verification. If you choose [Yes] for this
parameter, must first present a card, and then press fingerprint. If doesnt
swipe a card, there is no reflect to the finger press on the device.
34
Only Verify ID card: It is mainly designed for ID card, when you choose
[Yes], a user directly use ID card to verify, neednt to press fingerprint. When
you choose [NO], you must verify fingerprint after present the card, until
passing the verification.
Must Register Mifare Card: There are two statuses to register a Mifare
card, if the card was configure to [Must Register], it is only to verify the user
whose ID has stored in the FP device. The user without ID number cannot
verify. When you choose the item as [NO], whether there is users ID
information in the device or not, it will export after the user and fingerprint
template verified successfully.
5.5.5 Power Management

1. Click [Power] in the [Device Management], and click [Read Options]
to get the parameters of power.
Idle Option: Set the state when there is no operation on the device.
Idle minutes: When the idle minutes is 0, then the idle setup function is
off. When the value more than 0, the device will enter into idle state after
arrives at defined time.
35
5.5.6 Access Control
Click [Access Control] in the [Device Management], and then click

[Read Options], display the following interface
Lock Control Delay: Apply to determine unlock hour, the minimum

measured unit is 20ms. In the normal condition is 100-200ms.
Anti-Pass Mode: Can be set to "None", "Out ", In, In/Out.
Masters record state: Can be set to None, Out, In.
Sensor Mode: Set Door Sensor Mode. It can be set to None, N Open,
N Close state.
Normally Open: Set door state to open in normal situation.
Normally Close: Set door state to close in normal situation.
None: Do not use door sensor.
Sensor Delay: Set the sensor delay time when the door is opened. After
this defined time the sensor detect the door state. If the door state is not
consistent with the system, the alarm will be triggered.
Sensor Alarm: Set the alarm time delay after the alarm is triggered.
Range is 0-999 seconds.
36
Error times to alarm: Define the maximum error times to trigger the
alarm. When the verify is not through, and exceed this defined times, the
alarm signal will be triggered automatically.
5.5.7 Mifare
Select [Mifare] in [Device Management] interface, and then click [Read
Options], display the following interface.
FP Count: How many fingerprints stored in the Mifare card.

Start sector for FP: The first sector of Mifare card to store the
fingerprint.
Sector count for FP: The total sector that fingerprint occupied.
Card key: Set the password of read and write card, you can only setup,
cant read it.
5.5.8 Other Setup

Click [Other Setup] in [Device Management], and then click [Read
Options], the following interface appears.
37
Restart Device: Click the button to restart the device.

Power off Device: Shut down the device through the software.
Update firmware: Please do not upgrade the firmware at your discretion
because it may bring problems and affect the normal use of the device.
Contact our distributors for technical support or upgrade notification.
Clear admin privilege: This function can clear all administrator privilege
which has registered in the device.
Initial Device: This function is mainly used to clear all data in the device.
Sync Time: Synchronic the device time with the PC.
Capture Fingerprint: This function can be used to view fingerprint
image. If you want to check the fingerprint image, please place finger on the
sensor window, and then click this button, and will see the fingerprint image.
Date format: Select the date format in the down drop menu, and this
date format will display on the device starting interface.
Voice function: Including voice, voice verifies, keypad voice, you can
choose to open or close. You can set the voice volume too. This function is
available in the device which supports voice prompt function.
Operate Overtime: Set the device operation overtime, 30s by default.
38
5.5.9 U disk Settings

You can use the software to set the configuration file and store it in a U
disk. When the U disk is plug into a device, it can execute operations such as
Record download, User download, Upload users and Update firmware.
1. Click [U Disk] in [Device Management], enter the following interface.
2. Select the U disk from the down drop menu, click [Read Options].
39
3. Select the needed operation, click [Set Options], the system will
prompt [Operation finished], as shown below.
Thus the configuration file named operatemode.cfg store in the U disk.

The operation of execute the U disk configuration file please refer to the
related device user manual.
40
6. System Management
System management includes Operator Management, System
Operation Log, Backup Database, Clear Obsolete Data, Initial System, and
so on.
6.1 Operator Management

There are three options of operator management, Add Department
Administrator, Add Administrator and Delete Administrator. The following is
the add administrator operations for an example. The operation of [Add
Department Administrator] is similar to [Add Administrator].
The department administrator can not modify administrator password
and operation privilege after an administrator is added.
1. Click [Operator Management] in the [System Management] menu,
popup the administrator settings interface, like as the following figure.
2. Click [Administrator], and select [Add Administrator] in the down

drop menu, as the following figure.
41
3. In the popup user list box, select a user to be added as an

administrator.
Note: The administrator should be an enrolled user.
4. Click [OK], popup the following dialog, which means you have set this
user as an administrator, the user name and password is both the user ID.
42
Click [OK] to popup a privilege distributing list, put remarks in the

administrator privilege options, and then click [OK].
6. The adding operation is finished, as the following figure.
43
7. You can click [Edit Password] button to modify the administrators

password, as figure below.
8. You can click [Operation Right] button to modify the administrators

privilege.
Note: The original user name and password is both the user ID before
any modification.
If you want to cancel an administrator, select the administrator firstly, and

then click [Administrator], select [Delete Administrator] to complete the
44
operation process.
6.2 System Operation Log

The system operation log is a track record which records the software
operation history, and displays them in a list.
1. Click [System Operate Log] in the [System Management] menu,
popup the following interface.
45
2. Click [Delete], this operation is able to delete operation log to the

defined date, appear the following figure.
3. Select [Yes] on the popup interface to confirm the deletion, otherwise

select [No] to cancel the operation.
6.3 Backup Database

Backup the database and save it under a safe directory.
Recommendation: Backup the database regularly to ensure the data
security.
Click [Backup Database] in the [System Management] menu, popup a
dialog-box to backup database, you can name it as your favor, and save it in
the defined location.
46
6.4 Compact the Database

Compact the database to save the system space.
Note: This function is only capable to Access database.

Click [Compact the Database] in the [Data Maintenance] menu, to
compact the database, it is only capable to Access Database.
6.5 Clear Obsolete Data

You can use this function to clear the old data which are useless.
Click [Clear Obsolete Data] in the [Data Maintenance]. Click the down
drop menu to choose the date, and select the old record backup directory,
then click [OK] button to clear the old data.
Note: The deleted content doesnt include the end date being selected.
47
6.6 Initialize System

After this operation all the system will be initialized, and all data will be
cleared.
Click [System Initialization] in the [System Management] menu, popup
a warning dialogs, like as the following figure.
Note: All user data will be cleared after this operation, please use it with
caution.
Click [Yes] the system will clear all the data and restore to the initial state.
Otherwise click [No] to cancel the operation and back to the main interface.
6.7 Set Database

The system uses Microsoft ADO database interface, the default
database is Access2000, the database file named att2000.mdb. You can set
the database connection by the actual situation.
1. Connecting Microsoft Access Database setup
(1) Provide program to select Microsoft Jet 4.0 OLE DB Provider
48
(2) Click [Next] or [Connection] to enter the following interface.
Click button to select the database file.

Stand-alone use: Select the attendance database in the popup File
49
Manager menu. The default file path is:

C:\ Program Files\Enrollment\ATT2000.mdb.
Internet use: Suppose there are three networking registration systems,
where three sets of computers were named as PC1, PC2, PC3, and PC1 is
the host. Firstly, set the installation directory of PC1 database to share, and
let the other two computers have the access to read and write. The PC1
database points to the local database; and the other two computers database
are point to PC1s database. Then the data sharing can be achieved.
2. SQL Server Database Connecting Setup
First you should establish the empty database on the database server.
You can find a script file with the name of sqlserver.sql in the directory of
installing CD. The empty database is established in the front of the searcher
of SQL Server, and then opens the sqlserver.sql script files, to run database
which is to create this software.
In the Provider Select Microsoft OLE DB Provider for SQL Server, click
[Next] or [Connection] to enter this following.
50
Confirm the server name for storing this database, information for
logging on this server, and the database name. After run test connection
successfully, click [OK] button to complete settings.
6.8 Set Password of Database

We suggest user to set the password of database, in order to encrypt the
database and ensure the system security. Anytime when you open the
database, you should input the database password firstly, to avoid the
intended destruction of the database.
Note: This function is only available for Access database.

Click [Database Password] in the [System Management] menu, input
the new password in the popup dialogs box. Please distinctly keep in mind
the password after set it.
51
7. Other Functions
7. Other Functions
7.1 Update Firmware
If the device has the older firmware, you can update the firmware by right
click the device icon, and select [Update Firmware] in the menu. You must
keep the power and connection between PC and device when updating. After
updating, you need to restart the device.
Note: Please do not upgrade the firmware at your discretion because it

may bring problems and affect the normal use of the device. Contact our
distributors for technical support or upgrade notification.
7.2 Restart Device

If you want to restart the device using the software, please right click the
device icon, and click [Restart Device] to restart it. The operation result will
display on the lower side of the main interface.
52
7. Other Functions
7.3 Property
Please right click the device, and select [Property] in the down drop
menu. Enter the [Device Management] interface, the specific operation
please refer to 5.5 Device Information.
53
8. Appendix
8. Appendix
8.1 Connect with Device
The system provides four connection modes: RS232, RS485, TCP/IP
and USB.
8.1.1 RS232 Mode

Operation Steps:
1. Use RS232 to connect the device and computer. Refer to the
installation guide for detailed connection.
2. Click [Menu] -> [Setting] -> [Communication Setting] to set RS232
communication mode for the device. Please pay attention to the Baud Rate,
Device ID, Ethernet, RS232 and the setting of Connection Key.
3. After setting, press [ESC] to enter the saving interface, select [OK] to
save the settings and select [ESC] to cancel.
Note: After saving the settings, the device needs to be restarted.

4. Open the software, enter device management menu to add device:
Click menu: [Basic Settings] -> [Device Management]; or click [Device
Management] shortcut directly.
54
8. Appendix
5. Click [Add] in [Device Management] window to start connection of

system and the device.
6. The following is the communication interface. The information input
here must agree with the communication setting of step 2 in the device.
Device ID: Same to the device num set in the device. If the devices
setting is 1, input 1 here.
Port: Select the communication port number to connect PC and device,
and default COM1. It can be other ports, please select it carefully.
55
Baud Rate: 115200 is suggested when It is connected through RS232.

Communication Key can be ignored under the condition of default. If
communication password is set, input the corresponding password (5 digits
at most)
Name: Input name which is easy to remember according to devices
purpose.
7. After setting, click [Connect]. If dialogue box of [Test connection
succeeds] appears, then the connection between the device and system has
been done. If the dialogue box of [Test connection fail] appears, please
check the settings in step 2-6, and click [Connect] again.
For others device connection, repeat the operation above.
If you want delete a device, click the device and click [Delete].
8.1.2 RS485 Mode

Operation Steps:
The operation is similar to RS232 mode, the interface is as follows.
The parameters are set as following descriptions.

Device ID, Port, Communication Key, and Name please refer to the
56
8. Appendix
description for the RS232 method.

Baud rate: The baud rate of 38400/9600 are suggested when it is
connected through RS485.
Note: RS232/RS485 converter is not contained in the standard
configuration.
8.1.3 TCP/IP Mode

Operation Steps:
57

IP Address: the default value is 192.168.1.201. IP address can be
modified according to your LAN network segment. But it cannot bring conflict
with any terminal address.
Port: default value is 4370, which need not modify.
Communication Key and Device Name: Please refer to the description
for the RS232 method.
58
8. Appendix
8.1.4 USB Mode

Operation Steps:

Device ID Same to the device num set in the device. If the devices
setting is 1, input 1 here.
Communication Key and Name: please refer to the description for the
RS232 method.
Note: Only the device supports USB communication can use this mode.
8.2 Fingerprint Algorithm License
1. Right click [My Computer] by the mouse, and select [Properties], as
shown below:
59
2. Enter the dialogue box of system properties, select [Hardware], and

click [Device Manager], as shown below:
3. Device named [Biometric] can be found in [Device Manager], as

shown below:
60
8. Appendix
4. Right click the device, and select [Properties] in the menu, as shown
below:
5. The devices properties, type, manufacturer and position as shown
61
below. It is indicates the device possesses a SDK license.
8.3 The toolbar for datasheet operation
The line where the blue bar is located is named as current line. All
operation for datasheet is performed on the current line. Only black button is
operational, it can not operate when it is gray.
Click the button, put it to corresponded operate.
: First, move from the current line to the first line.
: Previous, move from the current line to the previous line.
: Next, move from the current line to the next line.
62
8. Appendix
: Last, move from the current line to the end line.
: Insert, add new record.
: Delete, cancel current record.
: Edit, enter edit status to modify record.
: Save, save the record to be edited.
: Cancel edition, cancel modification for the record.
8.4 Date
The data format of this manual is displayed as below.
Click the down-drop menu, the date interface pops up, as shown below.
Click < or > to select an earlier or a later month in the down drop
menu. Click the wanted day and it will display in the date box.
63
8.5 Sort Order

You can arrange the records according to the ascending or descending
order in the record list, directly click the head of rank to achieve.
As figure below, sort the users as the name order.
Choose a triangle symbol which is beside the field, according to

ascending order to arrange when the triangle symbol point upwards,
otherwise that means the sort order follow the descending order. You can
click the triangle symbol to change the rise or down rank.
8.6 Filtrate Data

Filtrate data is that select the records which meet defined condition from
the original table sheet. The current display window is as following, the
operation flow of the filtration datas command.
(1) Click down drop menu of the data rank, appear the following figure.
64
8. Appendix
(2) You can also use [Custom Filter] to fulfill the advanced data filter.
Click [Custom Filter], appear the following figure.
(3) Input condition, such as show all user whose surname contains L,
appear the following figure.
65
Note: % must be English symbol. Chinese symbol is invalid.

(4) Click [OK], to show the result of filtration.
: Whether do use the filtrate condition.

: Cancel filtrate operation.
If you want to cancel current filtration result, and display all records, click
or .
8.7 Record Group and Statistics

You can group the records according to one field or multi-field. You want
66
8. Appendix
can just drag the rank head to upper empty part, as the following figure.
The software can automatically count the total records and count the
grouping records. Such as the figure above, the department R&D, Count=2
means there is two person in this department. 9 at the left lower corner of
the interface, means there are 9 records totally.
67
9. End User Software License Agreement

End User Software License Agreement
LICENSE
Our company will grant you the use right of this software program, but
you must ensure: dont use, copy, edit, rent or attorn this software or any
parts of this software beyond the terms in this agreement.
YOU MUST ENSURE:
1. Only use this software in one computer.
2. In order to be used in this computer, the systems copy must be made
in readable format to prepare backup or manage files.
3. The system and the license agreement can be attorney to the third
party under the condition that the third party accepts the terms of this
agreement. When attornment happens, the original files and their copies
must be attorned together, or destroy all the copies which are not attorned.
4. Only use this software in multi-user environment or network system in
one of the conditions below:
There is proclamation which allows using this software in multi-users
environment or network system;
Or every node/end has purchased the using license of this software.
OTHER RESTRICTIONS:
1. Dont attorney the systems license again,
2. Dont decompile, disassemble, or reverse-engineer this software,
3. Dont copy or attorney this system or any parts of the system beyond
the terms of this agreement. Your license will end automatically when this
system or all or parts of this system are attorned to the third party.
COPYRIGHT AND PROPERTY:
The name of this software and its duplications must be together with the
company indicated in CD or in software.
68
The software and its documents are protected by copyright laws and
international treaty provisions.
You cannot delete the copyright announcement from the software, and
guarantee to replicate the copyright announcement for the duplications of the
software. You agree to stop any illegal duplicating actions for this
SOFTWARE and its documents.
LIMITED WARRANTY:
Our company warrants that if use the software in normal condition, there
will be no materials or craft defects in software in 90 days since the sell date.
If there is defect indeed after validation, our responsibility is to change good
software for you as the only compensation.
If the defects are caused by accidents, or misuse or incorrect use, this
warranty will be of no effect.
The warranty days for the exchanged software are the rest of the
warranty days of the original software, or 30 days if the rest of days are less
than 30 days.
NO OTHER WARRANTIES:
There are no any other warranties besides the above ones.
LIMITED LIABILITY:
The above warranty refers to all, both pointed content and implied
content, including, commodity and adaptability of special application purpose.
Whether both parties abide by this agreement or not, Our company and our
agent & seller have no responsibility for the profit loss, lost availability,
business interruption, or any indirect, special, inevitable damage, or any
compensation claim brought by this system, even if our company is
informed in advance that such things can happen.
TERMINATION
Without prejudice to any other rights, our company may terminate this
agreement if you fail to comply with the terms and conditions of this
69
agreement. In such event, you must destroy all copies of the software and all
of its component parts, or give them back to our company.
GOVERNING LAWS:
Such as Intellectual Property Rights Protection, Copyright Law and
Patent Law and so on.
70

Enrollment & Management Software User Manual V2.4.3.1037

Uploaded by

Document Informationclick to expand document informationManual del soft tk

Document Informationclick to expand document information

Copyright:

Available Formats

Enrollment & Management Software User Manual V2.4.3.1037

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Enrollment & Management Software User Manual V2.4.3.1037

Uploaded by

Copyright:

Available Formats

Enrollment & Management Software

About This Manual

5.5.5 Power Management ............................................................. 35

8.7 Record Group and Statistics .......................................................... 66

3. Install and Uninstall Software

Note: Press [Cancel] in this interface to stop the installation process.

4. Please read the License Agreement carefully. If you want to install it

6. Select the component to install. Its recommended to select all

7. This interface is to confirm the shortcut which is created in [Start] ->

3.2 Uninstall Software

4. Click [Set Password] and input the same password twice.

4.2 Modify Users Information

2. Modify the desired information. For example, change the user

3. After editing, click to save, or click to cancel.

4.3 Department Management

4.3.1 Add Department

4. Add other departments as step 2-3, thus the department is added to

4.3.2 Modify Department

4.3.3 Modify Department Relationship

1. Select the department which needs to modify.

2. Drag the department to the target position. Such as drag the

Thus the department [Test] is a sub department of [R&D Dept.].

4.3.4 Delete Department

2. Click [Delete] button to popup the confirm message, as shown below.

3. Click [OK] to delete, otherwise click [Cancel] to cancel.

4.3.5 Add User to Department

All users are belonging to the department of [company] by default.

1. Firstly select the department of [company], then click [User] button,

popup the following interface.

3. Click [Close] to return to the department management interface. Click

2. Click [Add] button, display the following interface.

3. After setting the parameters, click [Connect] to check the connection.

4. If it prompts [Failed in connecting with device], return to the step 2

6. The devices connecting parameters will be preserved in the system. If

5.2 Enroll User Fingerprint

5.2.1 Fingerprint Sensor Enrollment

8. Press the finger on the device. The enrollment succeeds if the

5.2.2 Fingerprint Device Enrollment

1. Click [User Management] in [Basic Settings] menu, or click [User

5.3 From Device to PC

4. Click [Download] to download user and fingerprint data. The system

5.4 From PC to Device

Upload users information and fingerprint data from the computer to

5. After uploading succeeds, the operation information will display on the

5.5 Device Information

5.5.1 Device Information

2. If you want to change some communication parameters, modify it as

Wiegand Setting includes Wiegand output and input settings.

defined by user and can be used repeatedly, range is 0-255).

E Facility code ID Number O

2. You can modify the parameters as needed, to obtain the best

5.5.5 Power Management

5.5.6 Access Control

Click [Access Control] in the [Device Management], and then click

Lock Control Delay: Apply to determine unlock hour, the minimum

FP Count: How many fingerprints stored in the Mifare card.

5.5.8 Other Setup

Restart Device: Click the button to restart the device.