WIRELESS SYSTEM

QLX-D
USER GUIDE

2014 Shure Incorporated

27A22351 (Rev. 1)
IMPORTANT SAFETY INSTRUCTIONS 14. REFER all servicing to qualified service personnel. Servicing is required when the ap-
paratus has been damaged in any way, such as power supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
1. READ these instructions.
exposed to rain or moisture, does not operate normally, or has been dropped.
2. KEEP these instructions.
15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with
3. HEED all warnings.
liquids, such as vases, on the apparatus.
4. FOLLOW all instructions.
16. The MAINS plug or an appliance coupler shall remain readily operable.
5. DO NOT use this apparatus near water.
17. The airborne noise of the Apparatus does not exceed 70dB (A).
6. CLEAN ONLY with dry cloth.
18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a
7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventila-
protective earthing connection.
tion and install in accordance with the manufacturers instructions.
19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
8. DO NOT install near any heat sources such as open flames, radiators, heat registers,
moisture.
stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open
20. Do not attempt to modify this product. Doing so could result in personal injury and/or
flame sources on the product.
product failure.
9. DO NOT defeat the safety purpose of the polarized or groundingtype plug. A polarized
21. Operate this product within its specified operating temperature range.
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wider blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replace- This symbol indicates that dangerous voltage constituting a risk of
ment of the obsolete outlet. electric shock is present within this unit.
10. PROTECT the power cord from being walked on or pinched, particularly at plugs, conve-
nience receptacles, and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer. This symbol indicates that there are important operating and mainte-
12. USE only with a cart, stand, tripod, bracket, or table specified by the manu- nance instructions in the literature accompanying this unit.
facturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
WARNING: This product contains a chemical known to the State of California to cause cancer and birth
13. UNPLUG this apparatus during lightning storms or when unused for long defects or other reproductive harm.
periods of time.
 WARNING
Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140F (60C), or
incinerate.
Follow instructions from manufacturer
Only use Shure charger to recharge Shure rechargeable batteries
WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type.
Never put batteries in mouth. If swallowed, contact your physician or local poison control center
Do not short circuit; may cause burns or catch fire
Do not charge or use battery packs other than Shure rechargeable batteries
Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs.
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like

WARNING: Danger of explosion if battery incorrectly replaced. Operate only with Shure compatible batteries.

Note: Use only with the included power supply or a Shure-approved equivalent.

LICENSING INFORMATION
Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or
modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is
the users responsibility, and licensability depends on the users classification and application, and on the selected frequency. Shure strongly urges the user to contact the
appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada.

Caution: Avoid operating mobile phones and mobile broadband devices near your wireless system to prevent the possibility of interference.

Information to the user

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Australia Warning for Wireless

This device operates under an ACMA class licence and must comply with all the conditions of that licence including operating frequencies. Before 31 December 2014, this
device will comply if it is operated in the 520-820 MHz frequency band. WARNING: After 31 December 2014, in order to comply, this device must not be operated in the
694-820 MHz band.

3
Contents
System Overview....................................................................................................................................................................................................................................5

Features..................................................................................................................................................................................................................................................5

Quick Start..............................................................................................................................................................................................................................................6

Receiver Front and Back Panels...........................................................................................................................................................................................................7

Transmitters............................................................................................................................................................................................................................................8

Battery Installation.................................................................................................................................................................................................................................8

Transmitter Display................................................................................................................................................................................................................................9

Transmitter Menu Options and Navigation..........................................................................................................................................................................................9

Receiver Display...................................................................................................................................................................................................................................10

Navigating the Receiver Menus..........................................................................................................................................................................................................10

AA Batteries and Transmitter Runtime..............................................................................................................................................................................................11

Shure SB900 Rechargeable Battery...................................................................................................................................................................................................11

Creating Audio Channels....................................................................................................................................................................................................................12

Manual Group and Channel Assignment...........................................................................................................................................................................................12

Manual Frequency Selection...............................................................................................................................................................................................................12

Receiver Gain Adjustment..................................................................................................................................................................................................................13

Setting the Transmitter RF Power......................................................................................................................................................................................................13

Wearing the Bodypack Transmitter....................................................................................................................................................................................................13

Setting Regional TV Channel Spacing...............................................................................................................................................................................................13

Control Lock Options for the Receiver and Transmitter..................................................................................................................................................................14

Audio Signal Encryption......................................................................................................................................................................................................................14

Linking Two Transmitters to a Receiver............................................................................................................................................................................................15

Frequency Bands and Transmitter RF Power...................................................................................................................................................................................15

Custom Groups....................................................................................................................................................................................................................................16

Networking............................................................................................................................................................................................................................................17

Setting the IP Address and Subnet Mask Manually..........................................................................................................................................................................17

Network Scan........................................................................................................................................................................................................................................18

Connecting to an External Control System.......................................................................................................................................................................................18

Shure AXT600 Spectrum Manager Compatibility..............................................................................................................................................................................18

Using QLX-D with a Shure ULX-D System.........................................................................................................................................................................................18

Managing QLX-D with Wireless Workbench 6...................................................................................................................................................................................19

Firmware Updates................................................................................................................................................................................................................................20

Error Codes and Solutions..................................................................................................................................................................................................................20

Troubleshooting...................................................................................................................................................................................................................................21

Hardware and Connectors...................................................................................................................................................................................................................22

Optional Accessories...........................................................................................................................................................................................................................23

FREQUENCIES FOR EUROPEAN COUNTRIES.................................................................................................................................................................................26

Certifications........................................................................................................................................................................................................................................27

4
System Overview
QLX-D Digital Wireless delivers defined, streamlined performance with transparent 24-bit digital audio. Combining professional features with simplified setup and
operation, QLX-D offers outstanding wireless functionality for demanding live sound events and installations.

Shure digital wireless technology enables QLX-D to transmit clearly detailed audio with extended, virtually flat frequency response. Designed to be highly RF spectrum
efficient, QLX-D can operate more than 60 compatible channels simultaneously in a single frequency band. Automatic channel scan and IR sync make finding and
assigning an open frequency quick and easy. Ethernet connection provides networked channel scanning across multiple receivers and Shure Wireless Workbench
control software compatibility for advanced frequency coordination. AES-256 encryption comes standard and can be easily enabled for secure wireless transmission.

QLX-D also adds Shure rechargeable power options to provide dramatic long-term cost savings and extended transmitter battery life over alkaline batteries, and
battery metering that reports remaining runtime in hours and minutes. With clearly defined performance and innovation, QLX-D delivers the very latest in digital wireless
technology from Shure.

Features
Transparent 24-bit digital audio Ethernet networking for multiple receiver systems
Extended 20 Hz to 20 kHz frequency range (microphone dependent) Network channel scanning configures open frequencies for networked receivers
120 dB dynamic range Compatible with Shure Wireless Workbench 6 control software
Digital predictive switching diversity Remote control from a mobile device or tablet via ShurePlus Channels app
64 MHz tuning bandwidth (region dependent) AES-256 encryption for secure wireless transmission
More than 60 available channels per frequency band (region dependent) Elegant and easy-to-use interface with high-contrast LCD menu
Up to 17 compatible systems per 6MHz TV band; 22 systems per 8 MHz Compatible with external control systems such as AMX or Crestron
band Professional-grade all-metal construction
Easy pairing of transmitters and receivers over IR scan and sync Transmitters use 2 AA batteries or Shure SB900 rechargeable battery
Automatic channel scan

System Components
menu

enter sync

on

QLXD4 Receiver 1/2 Wave Antennas (2) AA Alkaline Batteries

PS23 Power Supply 2 ft. BNC Cables with Bulkhead Adapters (2) (not included in Argentina)
Choice of QLXD1 Bodypack Transmitter or QLXD2 Handheld Transmitter Rackmount Hardware

Model Variations
Model variations with additional components are available to meet specific performance situations.

QLXD2 Handheld Transmitter QLXD1 Bodypack Guitar System QLXD1 Bodypack Headworn or Bodypack and Handheld Combo
Lavalier System
Includes QLXD2 Handheld, available Includes QLXD1 bodypack Includes QLXD1 bodypack, available QLXD1 bodypack transmitter with
with any of the following microphone transmitter with any of the following microphone WL185 Microflex cardioid lavalier
cartridges: WA305 Premium instrument cable cartridges: microphone
SM58 Zipper Bag Beta 98H/C QLXD2 handheld transmitter
Beta 58A WL93 with Shure SM58 microphone
SM86 WL183 cartridge
Beta 87A WL184 Battery Contact Cover
SM87A WL185 Zipper Bag (2)
Beta 87C MX150 (omni)
KSM9 MX150 (cardioid)
KSM9HS (black) MX153 (black or tan)
Microphone Clip SM35
Battery Contact Cover Zipper Bag
Zipper Bag

5
Quick Start
Step 1: Power and Antenna Connection Step 2: Scanning for the Best Available Channel
Connect an antenna to each of the antenna connectors. 1. Press the menu button on the receiver to access the scan function.
Connect the power supply to the receiver and plug into an AC power II
III
II I I I I I I III
II

source. scan

IIIIII
IIIII
II
III
I I I I I I I I II
II
I
menu

Connect the receiver audio output to a mixer or amplifier. audio rf ir

Press and hold the power button to turn on the receiver.

enter sync
group channel

2. Press the enter button to start a frequency scan. The scan icon will flash while
in scan mode. When the scan is complete, the selected group and channel
appear on the display.

TV MHz menu

audio rf ir
dB
enter sync
group channel rf audio gain
PS23

INSTRUMENT OUT

INSTRUMENT OUT

Step 3: Install Batteries into Transmitter



AA Batteries Shure SB900 Battery

on
ULXD2

on

on

AA Adapter AA Adapter

Accessing the Battery Compartment Installing Batteries

Press the side tabs on the bodypack or unscrew the -- AA Batteries: Place batteries (note polarity markings) and AA Adaptor as shown
cover on the handheld as shown to access the battery -- Shure SB900 Battery: Place battery as shown (note polarity markings), remove AA Adaptor from
compartment. bodypack transmitter, stow AA Adaptor in door for handheld transmitter
Note: If using AA batteries, select a battery type from the transmitter menu to ensure accurate battery
metering.

Step 4: IR Sync to Create an Audio Channel 4. syncgood appears on the display when IR sync is complete. The blue
rf LED will illuminate indicating that the transmitter is within range of
1. Turn on the transmitter.
the receiver.
2. Press the sync button on the receiver. The red ir LED Note: If the IR sync fails, repeat the IR sync procedure, carefully maintaining
will blink indicating that sync mode is active. alignment between the IR windows of the transmitter and receiver.
3. Align the IR sync windows of the transmitter and l l l
l ll l l l
l l
receiver at a distance of <15 cm (6 in.). When the l l menu
l l l l
l l l l

transmitter and receiver are aligned, the red ir LED lll l ll lll lll
lll

lll
lll

lll

llllll lll lll

remains on and the sync will automatically occur.

ll audio rf ir
l l
< 15 cm (6 in.)
l l l enter sync
l l l l l l

Step 5: Sound Check and Gain Adjustment

1. Test the transmitter at performance levels while monitoring the audio meter and the
audio LED. The audio meter should display at least 3 bars and the audio LED should TV MHz

be green. Reduce the gain if there is audible distortion of the audio.

hr mn

dB

2. Increase or decrease the gain if necessary by pressing the arrow buttons on the group channel rf audio gain

receiver front panel.

6
Receiver Front and Back Panels

6 7 8 9 10

1 2 3 4 5

Display Menu Button

Shows menu options, receiver and transmitter settings. -- Press to access or select menu screens
-- Press to cancel pending changes
Arrow Buttons -- Press and hold to return to the home screen
Adjust gain setting or change menu parameters.
RF LED
Enter Button Illuminates when RF link with transmitter is active.
Press to save menu or parameter changes.
IR Window
Sync Button Align with the transmitter IR window during an IR sync to automatically program
Press to activate IR sync. transmitters.

Power Switch Sync LED

Powers receiver on or off. -- Blinking: IR sync mode is enabled
-- On: Receiver and transmitter aligned for IR sync
Audio LED
-- Green = normal
-- Yellow = signal approaching limiter threshold
-- Red = limiter engaged to prevent clipping

11 12 13 14 15 16 17 18 15

Power Cord Strain Relief Receiver Reset

Secures power cord. Press to restore receiver default settings.

Power Supply Jack Antenna Connectors

Connection point for DC power supply. BNC connector for receiver antennas

Ethernet Port Mic/Line Switch

For network connection. Sets output level to microphone or line.
-- Amber LED (network speed): XLR Audio Output
off = 10 Mbps, on = 100 Mbps Balanced (1: ground, 2: audio +, 3: audio - )
-- Green LED (network status):
off = no network link, on = network link active 1/4" Instrument/Auxiliary Output
flashing = rate corresponds to traffic volume Impedance Balanced (Tip: audio, Ring: no audio, Sleeve: ground)

7
Transmitters
Power LED Battery Compartment
-- Green = unit is powered on Requires 2 AA batteries or a Shure 10
-- Red = low battery SB900 rechargeable battery.
On/Off Switch AA Battery Adapter
Powers the transmitter on or off. Secures batteries when powering 11 1 2
Display: transmitter with AA batteries
View menu screens and settings. Press any instead of Shure SB900 battery.
control button to activate the backlight. Bodypack Antenna 8
IR window For RF signal transmission.
Align with the receiver IR window during an IR 3
Handheld Integrated Antenna QLXD2

3
QLXD1

sync for automated transmitter programming. For RF signal transmission. 4

Menu Navigation Buttons Microphone Cartridge 4
on

menu = Use to navigate between menu 2

See Optional Accessories for a list
screens. of compatible cartridges. 5
5
= Use to select menu screens, edit menu
TA4M Input Jack 6
parameters, or choose a home screen display
Connects to a 4-Pin Mini
option.
Connector (TA4F) microphone or
enter = Press to confirm and save parameter 6
instrument cable. 7
changes.
Battery Contact Cover
Tip: Press the menu button to exit without
Align the cover as shown to 7
saving parameter changes.
prevent reflections from the battery
contacts during broadcasts or
performances.
12
9

Battery Installation


AA Batteries Shure SB900 Battery

on
ULXD2

on

on

AA Adapter AA Adapter

Accessing the Battery Compartment Installing Batteries

Press the side tabs on the bodypack or unscrew the cover on -- AA Batteries: Place batteries (note polarity markings) and AA Adaptor as shown
the handheld as shown to access the battery compartment. -- Shure SB900 Battery: Place battery as shown (note polarity markings), remove AA Adaptor from
bodypack transmitter, stow AA Adaptor in door for handheld transmitter
Note: If using AA batteries, set the battery type using the transmitter menu.

Setting the AA Battery Type AA Battery Installation

To ensure accurate display of transmitter runtime, set the battery type in the transmitter Fully insert the batteries as shown to ensure proper battery contact and to
menu to match the installed AA battery type. If a Shure SB900 rechargeable battery is allow the door to latch securely.
installed, selecting a battery type is not necessary and the battery type menu will not
be displayed.

1. Press the menu button to navigate to the battery icon.

2. Use the buttons to select the installed battery type:
-- AL = Alkaline
-- nH = Nickel Metal Hydride
-- Li = Lithium Primary
3. Press enter to save.
Correct Incorrect

8
Transmitter Display

Battery Indicator Encryption Status

Bars displayed indicate remaining battery life. Icon displayed when encryption is
6 5
enabled.
Home Screen Display: Group and Channel/Frequency/SB900 4
Battery Runtime Lock
1 rf power
mic offset dB

Use the arrow keys to select one of the following home screen displays: Displayed when transmitter
controls are locked. 2
group channel MHz
Group and SB900 battery Frequency
RF Power
Channel runtime
RF power setting (Lo or Hi).
3
Mic Offset
group channel MHz
Displays micoffset level in 3
dB increments.

Transmitter controls
To increase, decrease or change a parameter, use the buttons
menu enter
To save a menu change, press enter

menu

enter
To exit a menu without saving a change, press the menu button
Bodypack

Handheld

Transmitter Menu Options and Navigation

The transmitter features individual menu screens for setting up and adjusting the transmitter. To access the menu options from the home screen, press the menu button.
Each additional press of the menu button advances to the next menu screen.

Home Screen
Use the arrow keys to select one of the following home screen
displays:
-- Battery Icon/group and channel
-- Battery Icon/frequency
-- Battery Icon/Battery Runtime (SB900 installed) MHz
group 1
Use the arrow buttons to scroll through the groups. III

II
I
channel
II IIII
8 2

IIIIIII
Use the arrow buttons to scroll through the channels. group channel
II
IIII

frequency
Use the arrow buttons to adjust the frequency. Press and hold for
III
faster scrolling. mic offset dB
II
I
II IIII

7 3 IIIIIII
lock
Select a lock option: group channel
II

IIII
5
-- On = controls locked
-- OFF = controls unlocked rf power 6 4
rf power
Select an rf power setting:
MHz
-- Lo = 1 mW
-- Hi = 10 mW
mic offset dB
Use to match audio levels between two transmitters used Tips for Editing Menu Parameters
in a combo system. Range is 0 to 21 dB (3 dB increments). To access the menu options from the home screen, press the menu button. Each
Adjustments occur in realtime. additional press of the menu button advances to the next menu screen.
battery type A menu parameter will blink when editing is enabled
Use to set the battery type to match the installed AA battery type To increase, decrease or change a parameter, use the arrow buttons
to ensure accurate battery metering. Menu is not displayed when
To save a menu change, press enter
Shure SB900 batteries are installed.
To exit a menu without saving a change, press menu

9
Receiver Display
Audio Meter Scan
13 12 11 10 9 8 Number of bars displayed corresponds to Displayed when scan function is active.
audio level.
Network Scan
scan -- OL = Illuminates when receiver audio Displayed when networkscan function
TV network MHz

14 hr mn
OL TxOL menu
power
gain
7 limiter is active to prevent clipping is active in multi-receiver systems.
-- TxOL = Illuminates when transmitter
15 dB 6 input is overloaded. Reduce input from Network Connection Indicator
group channel rf audio gain microphone or instrument to prevent Illuminates when additional Shure
clipping. components are detected on the
1 2 3 4 5 Gain Level network.
Displays receiver gain setting in 1 dB
increments. TV Channel
Displays the number of the TV channel
Group
Receiver Lock Status containing the selected frequency.
Displays group setting.
Lock icon and name of locked control:
Transmitter Battery Icon
Channel -- menu Indicates remaining battery life.
Displays channel setting.
-- power
SB900 Battery Runtime
Active Antenna Indicator -- gain
When the transmitter is powered by
Illuminates to indicate which antenna is active. Frequency Setting a Shure SB900 rechargeable battery,
RF Signal Meter Selected frequency (MHz). remaining runtime is displayed in
Number of bars displayed corresponds to RF signal level - hours:minutes.
Encryption Status
OL = overload. Illuminates when encryption is enabled.

Navigating the Receiver Menus

The receiver has a main menu for setup and configuration and an advanced menu to access additional receiver functions.

Main Menu Advanced Menu

Press the menu button to access the menu. Each additional press of the Starting from the main menu home screen, press menu while holding the enter
menu button advances to the next menu screen in the following order: button to access the advanced menu. Each additional press of the menu button
advances to the next menu screen in the following order.
1 2 3
TV MH z
scan
I I I
network scan
I I I I I I
1 2
I

I
I
I I I I

I I I I
I I I I

TV MH z
I I I

I I I
I I I

c h an n el channel group enter MHz TV MHz

+
I I I
I I I I I I
I

I I I
I
I

gro u p channel rf a ud io gain

I
I I I I

I I I
menu gro u p c ha n n e l
MHz I group channel rf audio g ain I I I

I
I I I I

I I I
I

I I
I I I

I I I I
I I

I
I I I I

I I I
I I I

I I I

channel
I I I
I

net wor k

7 6 5 4

6 5 4 3
Scan Lock
Receiver automatically scans Choose a control lock option
for the best available frequency IP Settings
Custom Groups
Encryption Use to select and edit IP settings and
Use to add channels and
Network Scan Use the arrow buttons to enable subnet masks
frequencies to Custom
Scans to find frequencies for encryption (on) or disable
Groups Network Reset
networked receivers operating encryption (off)
in the same frequency band Returns network settings and IP
TV Channel Spacing
Frequency Selects the regional
address to default setting
Group Use the arrow buttons to edit the bandwidth for TV channel Factory Reset
Edit the receiver group settings frequency value display Restores factory settings
Channel
Firmware Update For application and configuration details,
Edit the receiver channel
Use to update the transmitter see the related guide topic for each
settings
firmware advanced feature.

Tips for Editing Menu Parameters

To increase, decrease or change a parameter, use the arrow buttons
A menu setting will blink when editing is enabled
To save a menu change, press enter
To exit a menu without saving a change, press menu
To access the advanced menu, press menu while holding the enter button from the home screen
To return to the home screen from any menu without saving changes, press and hold the menu button.

10
AA Batteries and Transmitter Runtime
QLX-D transmitters are compatible with the following AA battery types:

Alkaline
Nickel Metal Hydride (NiMH)
Lithium Primary

A 5-segment battery indicator representing the charge level of the transmitter battery is displayed on the screens of the transmitter and receiver. The following tables
contain the approximate remaining transmitter runtime in hours:minutes.

Alkaline Batteries: Up to 9 Hours of NiMH Batteries: Up to 10 Hours of Lithium Primary Batteries: Up

Runtime Runtime to 16 Hours of Runtime
Battery Approximate Runtime Battery Approximate Runtime Battery Approximate Runtime
Indicator Remaining (hours:minutes) Indicator Remaining (hours:minutes) Indicator Remaining (hours:minutes)
9:30 to 7:30 10:00 to 8:00 16:00 to 12:45

7:30 to 5:30 8:00 to 6:00 12:45 to 9:30

5:30 to 3:30 6:00 to 4:00 9:30 to 6:30

3:30 to 2:30 4:00 to 2:00 6:30 to 3:15

2:30 to 1:30 2:00 to 0:20 3:15 to 0:20

< 0:30 0:20 to 0:00 0:20 to 0:00

Shure SB900 Rechargeable Battery

Shure SB900 lithium-ion batteries offer a rechargeable option for powering the QLX-D transmitters. Batteries quickly charge to 50% capacity in one hour and reach full
charge within three hours.

Single chargers and multiple bay chargers are available to recharge the Shure batteries.

Caution: Only charge Shure rechargeable batteries with a Shure battery charger.

Single Bay Charger Multiple Bay Chargers

The single bay charger offers a compact Shure offers two models of multiple bay
charging solution. chargers:

1. Plug the charger into an AC power SBC-200 two bay charger

LED
source or USB port. SBC-800 eight bay charger
2. Insert a battery into the charging bay.
Multiple bay chargers can charge
3. Monitor the charging status LEDs until
individual batteries or batteries installed
charging is complete.
in transmitters.

Charging Status LED

1. Plug the charger into an AC power source.
Color Status 2. Insert batteries or transmitters into the charging bay.
Red Charging 3. Monitor the charging status LEDs until charging is complete.

Green Charging Complete

Charging Status LED
Amber Flashing Fault: check connections and battery
Off No battery in bay Color Status
Green Charging Complete
Important Tips for Care and Storage of Shure Green/Red Charge level above 90%
Rechargeable Batteries Red Charging
Proper care and storage of Shure batteries results in reliable performance
Amber Fault: check connections and battery
and ensures a long lifetime.
Flashing
Always store batteries and transmitters at room temperature Off No battery in bay
Ideally, batteries should be charged to approximately 40% of capacity for
long-term storage
During storage, check batteries every 6 months and recharge to 40% of
capacity as needed

11
Creating Audio Channels
A wireless audio channel is formed when a receiver and transmitter are tuned to the same frequency. To ease setup, frequencies available to the QLX-D system are
organized into groups and channels. Each group contains a number of channels, and each channel is assigned to a specific preset frequency.

The QLX-D system provides 3 methods for tuning the receiver and transmitter to the same frequency:

Scan and IR Sync: The receiver scans the RF spectrum for the best available frequency and an IR sync automatically tunes the transmitter to the receiver frequency
Manual Group and Channel Assignment: Manually setting the receiver and transmitter to the same group and channel number forms an audio channel
Manual Frequency Assignment: Manually setting the receiver and transmitter to the same frequency rather than using groups and channels forms an audio channel
Important: Before you begin a scan or frequency assignment:

Turn off: All transmitters for system you are setting up to prevent interference with frequency scans.
Turn on: The following potential sources of interference including other wireless systems, computers, CD players, large LED panels, and effects processors to prevent
selection of occupied frequencies.

Scan and IR Sync

The simplest way to create an audio channel is to use the scan function to find the best available receiver channel, and then use the IR sync feature to automatically tune
the transmitter to the receiver channel.

Step 1: Scanning to Find the Best Group and Channel

IIIIIII I
scan
The Scan function automatically selects the best available receiver group and channel.

IIII
I
IIIIIIIIIIIII

IIIIIIIIIIIIII
1. Navigate to the Scan menu option.
2. Press enter to start the scan.

IIII
channel
IIII IIII
3. When the scan is complete, the group and channel will appear on the display.
II

Step 2: IR Sync for Automatic Transmitter Set Up

Performing an IR Sync automatically tunes the transmitter to match the receiver frequency, forming a wireless audio channel.

1. Turn on the transmitter.

2. Press the sync button on the receiver. The red ir LED will blink indicating that sync mode is active.
3. Align the IR sync windows of the transmitter and receiver at a distance of <15 cm (6 in.). When the transmitter and receiver
are aligned, the red ir LED remains on and the sync will automatically occur.
4. syncgood appears on the display when IR sync is complete. The blue rf LED will illuminate indicating that the transmitter
is within range of the receiver.
Note: If the IR sync fails, repeat the IR sync procedure, carefully maintaining alignment between the IR windows of the transmitter
and receiver.
< 15 cm (6 in.)

Manual Group and Channel Assignment

An audio channel can be manually created by simply setting the receiver and transmitter to the same group number and channel number. For example, a receiver set to
Group 2, Channel 3 and a transmitter set to Group 2, Channel 3 would form an audio channel.

Use manual group and channel configuration to assign specific groups and channels to receivers and transmitters as an alternative method to automatically creating
channels with IR sync.

Use the following steps to set the group and channel in the receiver and transmitter:

1. Navigate to the group setting.

IIIIIIIIIII II II
IIII II I
2. Use the arrow buttons to scroll through the groups.
I

IIII
IIIII
IIIIIIIIIIIIIIIIIIII

IIIIIIIIIIIIII
IIIIIIIII IIIIIIIIIII

IIIIIIIIIIIIII

3. Press enter to select a group.

4. Next, use the arrow buttons to select a channel. group channel
IIIII

IIII

IIIIIIIIIIIII IIIIIIIII
I

5. Press enter to save.

Manual Frequency Selection

Manual frequency selection can be used instead of groups and channels to set the transmitter and receiver to a specific frequency. For example, an audio channel can be
created by setting the receiver and transmitter to same frequency.

Setting the Receiver Frequency Setting the Transmitter Frequency

1. Press menu to navigate to the frequency 1. Press menu to navigate to the frequency setting
setting option. MHz
option.
2. Use the arrow buttons to adjust the 2. Use the arrow buttons to adjust the frequency. Press
frequency. Press and hold for faster scrolling. and hold for faster scrolling. MHz

3. Press enter to save. 3. Press enter to save.

12
Receiver Gain Adjustment
The gain control sets the overall signal level for the system. The default gain level is 12 dB and the available gain
range is -18 to 42 dB, in 1 dB increments.
TV MHz

Set the gain to a level where the audio LED appears green or yellow, with only the highest audio peaks causing the hr mn

LED to occasionally turn red and engage the limiter. Reduce the gain if there is audible distortion of the audio. channel rf audio gain
dB

From the receiver home screen, use the arrow buttons to increase or decrease the gain:

A single button press adjusts the gain in 1 dB increments

Press and hold the button for larger adjustments

Test the transmitter at performance levels when adjusting the gain. Monitor the audio meter and the audio LED to
prevent overloads.

Setting the Transmitter RF Power Wearing the Bodypack Transmitter

The transmitter offers two RF power settings which determine the transmitter Clip the transmitter to a belt or slide a guitar strap through the transmitter clip as
range. shown.

Lo = 1 mW For best results, the belt should be pressed against the base of the clip.
Hi = 10 mW
Use the Lo setting when the transmitter and receiver are in close proximity.

1. Navigate to the transmitter rfpower menu.

2. Use the arrow buttons to select Hi or Lo.
3. Press enter to save.

rf power rf power

Setting Regional TV Channel Spacing

The parameter for TV channel spacing allows the receiver to match regional TV bandwidth usage and accurately display local TV channels.

The following channel bandwidth options are available:

6MHz
TV MH z
7MHz
8MHz
6JP (Japan)
off (use to turn off TV channel display)
To set the TV channel spacing:

1. Press and hold the enter button, and then press the menu button to access the advanced features
menu.
2. Press the menu button to navigate to the TVCH menu.
3. Use the arrow buttons to select the channel bandwidth that corresponds to the local region.
4. Press enter to save.

13
Control Lock Options for the Receiver and Transmitter
Control lock options are available for both the receiver and the transmitter to protect against accidental or unauthorized changes. Locks can be directly set from the
component menu, or remotely set from WWB6. To maintain protection, controls remain locked when the transmitter is turned off and turned on.

Locking and Unlocking the Receiver Controls Locking and Unlocking Transmitter Controls
The receiver has the following control lock options which can be used The transmitter controls can be locked or unlocked by selecting On (locked) or
separately or in any combination: OFF (unlocked) from the transmitter lock menu.
gain: locks the arrow buttons to prevent changes to the audio gain settings If an attempt is made to access a locked control, the lock icon will flash,
menu: prevents access to menu items and IR sync (gain controls and power indicating that the transmitter controls are locked.
switch remain active)
power: disables power switch (gain and menu controls remain active) To set a transmitter lock:
To lock a receiver control:
1. Press the menu button to navigate
to the lock settings.
1. Press the menu button to navigate to To unlock a receiver: 2. Use the arrow buttons to select on.
the lock settings.
Tip: To unlock the menu and clear 3. Press enter to save. The lock icon
2. Use the arrow buttons to add or all locks, press and hold the menu appears on the display to confirm
remove the lock options shown next to button while in the home screen that the control locks are enabled.
the lock icon. until the unlock icon appears. Press To unlock the transmitter:
3. Press enter to save the lock settings. enter to confirm and save change.
1. Press and hold the menu button until
1. To unlock gain or power OFF and the unlock icon appear on
menu
settings, navigate to the lock the display.
OFF
gain

settings by pressing the menu

enter
button. 2. Press enter to save changes.
2. Press the arrow buttons to de-
select a lock option.
3. Press enter to confirm and save
change.

Audio Signal Encryption

The QLX-D receiver features Advanced Encryption Standard (AES-256) to protect the audio signal. When encryption is enabled, the receiver generates a unique
encryption key which is shared with a the transmitter during an IR sync. Transmitters and receivers that share an encryption key form a protected audio path, preventing
unauthorized access by other receivers. To maintain security, components remain encrypted when turned off and on.

Creating an Encrypted Audio Channel

1. Press the menu button to navigate to the encryption menu, indicated by the key icon.
2. Use the arrow buttons to select an encryption option:
-- on = encryption enabled
-- OFF = encryption disabled
3. Press enter to save. The key icon will be shown on the receiver display.
4. Press the sync button and align the IR sync windows of the transmitter and receiver. The encryption key
icon will appear on the transmitter screen when the IR sync is complete and the encryption key has been
transferred from the receiver.
Additional transmitters can share the same encryption key with a single receiver. Perform an IR sync to encrypt
each additional transmitter.

Note: When OFF is selected to disable encryption, perform an IR sync to clear the encryption key from the
transmitter and prevent an encryption mismatch error or FAIL message.

< 15 cm (6 in.)

Removing Encryption
1. Press the menu button to navigate to the encryption menu.
2. Select OFF.
3. Press enter to save.
4. IR sync the transmitter and receiver to clear the encryption key from the transmitter and prevent an encryption key mismatch between components, indicated by a
FAIL message.
Note: If encryption has been set from off to on, the receiver will generate a new encryption key and must be IR synced to the transmitter to share the new key.

14
Linking Two Transmitters to a Receiver
Linking two transmitters to a receiver offers the flexibility to provide a performer with either a handheld or bodypack transmitter to meet their preference. For performances
requiring instrument changes, two bodypack transmitters can be linked to a single receiver.

Note: Only turn on and operate one transmitter at a time to prevent interference between the transmitters.

Syncing the Transmitters to the Receiver

Both transmitters must be individually linked to the receiver by performing an IR Sync.

1. Turn on the first transmitter and perform an IR Sync with the receiver.
2. Perform a sound check and adjust the transmitter gain if necessary. When finished, turn off the transmitter.
3. Turn on the second transmitter and perform an IR Sync with the receiver.
4. Test the transmitter at performance conditions and adjust the transmitter gain if necessary. When finished, turn off the
transmitter.

< 15 cm (6 in.)
Matching Audio Levels with Mic Offset
When linking two transmitters to a receiver, there may be a difference in volume levels between microphones or instruments.
If this occurs, use the MicOffset function to match the audio levels and eliminate audible volume differences between
transmitters. If using a single transmitter, set MicOffset to 0 dB.
mic offset dB
1. Turn on the first transmitter and perform a sound check to test the audio level. Turn off the transmitter when finished.
2. Turn on the second transmitter and perform a sound check to test the audio level.
3. If there is an audible difference in the sound level between the transmitters, navigate to the MicOffset menu on the
transmitter to increase or decrease the Mic Offset in realtime to match the audio levels.

Frequency Bands and Transmitter RF Power

Band Frequency Range RF Power (mW) Band Frequency Range RF Power (mW)
(MHz) (MHz)
G50 470 - 534 1 or 10 K52 606 - 670 1 or 10
G51 470 - 534 1 or 10 L50 632 - 696 1 or 10
G52 479 - 534 1 or 10 L51 632 - 696 1 or 10
H50 534 - 598 1 or 10 L52 632 - 694 1 or 10
H51 534 - 598 1 or 10 L53 632 - 714 1 or 10
H52 534 - 565 1 or 10 P51 710 - 782 1 or 10
H53 534 - 598 1 or 10 P52 710 - 782 1 or 10
J50 572 - 636 1 or 10 Q51 794 - 806 1 or 10
J51 572 - 636 1 or 10 S50 (823 - 832) (863 1 or 10
- 865)
JB 806 - 810 1 or 10
X51 925 -937.5 1 or 10
K51 606 - 670 1 or 10

15
Custom Groups
Specific channels and frequencies can be selected and placed into custom groups. Custom groups are commonly used to assign networked receivers to a specific range
of frequencies or to pre-configure receivers for rental applications. Once a custom group has been created, it can be loaded to the receiver using the group menu.
When network scan is used to assign frequencies from a receiver with a custom group selected, all of custom groups (U1, U2, U3, etc...) from that receiver will be loaded
to all other receivers on the network.

Creating Custom Groups

I I I I I I I I
I I I I I
I I
MHz

I I I
TV MHz TV MHz

I I
I I I
I I I
I I
I I I
I I I
I I I I I I I
I
I I I I

I
I I I I
I I I

I I I
group cha nnel
group cha n n e l gro up ch a nn e l
I I I
I

I I I

I
Selecting A Custom Group
The receiver has 6 custom groups available named U1, U2, U3, U4, U5, and U6.
a. Press menu while holding the enter button to access the Custom Group screen.
b. Press enter to enable editing of a group (indicated by the group flashing).
c. User the arrow buttons to select a group (U1 to U6).
d. Press enter to advance to channel selection.
Selecting a Channel
a. Use the arrow buttons to select a channel (1-60). Each group can contain up to 60 channels (frequencies).
b. Press enter to save the selected channel and advance to frequency assignment.
Assigning a Frequency to a Channel
a. Use the arrow buttons to assign a frequency to the selected channel.
b. Press enter to save.
After pressing enter, the channel will flash to allow for adding more channels and frequencies to the custom group. To add more channels and frequencies, repeat
steps 2 and 3. When finished, press the menu button several times to return to the main menu.

Transmitter IR Sync from a Custom Group

To ensure accurate display of group and channel information, IR sync the transmitter from the CustomGroup menu screen:

1. Press menu while holding the enter button to access the Custom Group screen.
2. Turn on the transmitter and press the sync button on the receiver.
3. Align the IR sync windows of the transmitter and receiver.
4. syncgood appears on the display when IR sync is complete.
Note: If the IR sync fails, repeat the IR sync procedure, carefully maintaining alignment between the IR windows of the transmitter and receiver.

Deleting a Custom Group

1. Press menu while holding the enter button to access the Custom Group screen.
2. Press enter to enable editing of a group (indicated by the group flashing).
3. User the arrow buttons to navigate to display the group number and the words DEL.
4. Press enter to delete the group.
To delete individual channels from a custom group, do the following:

1. Enter the custom groups menu and select the frequency for the channel to be deleted.
2. Press and hold an arrow button until the frequency displays ---.---MHz.
3. Press and hold the menu button to confirm change and exit.

Creating Custom Groups using Wireless Work Bench 6

Custom groups can be created in WWB6 by accessing the Frequency Coordination tab. Refer to the WWB6 help system for detailed instructions for configuring Custom
Groups.

16
Networking
The receiver uses an Ethernet connection to network with other components and includes an internal DHCP client for automatic network configuration when connected to
a DHCP enabled router.

Connecting to a Network Network Troubleshooting

1. Insert an Ethernet cable in the Ethernet port on the rear of the receiver. Use only one DHCP server per network
2. Connect the cable to a computer or router. All devices must share the same subnet mask
3. The port LEDs on the receiver will illuminate to indicate network All receivers must have the same level of firmware revision installed
connectivity and network traffic. Look for the illuminated network icon on the front panel of each device:
If the icon is not illuminated, check the cable connection and the LEDs on the
Automatic IP Addressing Ethernet port.
1. Enable a DHCP service on the server or use a DHCP enabled router. If the Ethernet port LEDs are not illuminated and the cable is plugged in, replace the
2. When the receiver is powered on, the DHCP server will automatically cable and recheck the LEDs and network icon.
assign an IP address to the receiver.
To check connectivity of WWB6 to the network:
Tip: Use the network reset option available in the advanced features menu 1. Start WWB6 software and use Inventory view to see devices connected to the
to return the receiver to the default DHCP addressing mode. network.
2. If not, find the IP address from one of the devices on the network (such as a
Configuration Tips receiver) and see if you can ping it from the computer running WWB6.
Use shielded Cat 5 or better Ethernet cables to ensure reliable network 3. From a WINDOWS/MAC command prompt, type ping IPADDRESS of the device
performance (e.g. "ping 192.168.1.100").
The LEDs on the Ethernet port illuminate indicating a network connection 4. If the ping returns success (no packet loss), then the computer can communicate
is active with the device on the network. If the ping returns failure (100% packet loss), then
The network icon illuminates when the receiver detects additional Shure verify that the IP address of the computer is on the same subnet as the receiver.
devices on the network 5. If the pings are successful and the devices still do not show up in the WWB6
All components must operate on the same subnet inventory, check to ensure all firewalls are either disabled or allow the WWB network
traffic to pass to the application. Check that firewall settings are not blocking network
Use multiple Ethernet switches to extend the network for larger
access.
installations

Setting the IP Address and Subnet Mask Manually

IP addresses and subnet masks can be manually set from the advanced menu in the receiver or from the monitor panel in Wireless Workbench 6.

Network settings entered manually must be valid and conform to IP protocols to ensure proper network communication.

Receiver Menu
IP addresses and subnet addresses contain 4 groups of numbers. Each group
can contain up to 3 digits. A decimal point separates each group.
000. 000. 000. 000
When setting an IP address or subnet address, each of the 4 groups must be
edited individually. The following diagram shows how the groups are mapped to
the receiver display:

1. Press menu while holding the enter button to access the advanced menu.
2. Press the menu button to navigate to the IP menu.
3. Use the arrow buttons to set the mode to St (static) and press enter.
4. Use the arrow buttons to edit the first group. Press enter to save and continue to the next group.
5. Use the arrow buttons and enter button to edit the remaining 3 groups.
6. When group 4 has been edited, the display will show the subnet mask menu. Use the arrow buttons to scroll and select a preset value for each of the subnet mask
groups.
7. When finished, press enter to save settings.

Note: To restore automatic DHCP IP addressing, enter the IP menu and select AU (automatic). The NetworkReset menu option can also be used to restore DHCP
addressing.

Wireless Workbench 6
1. Open the ChannelProperties tab in WWB6.
2. Click on Utilities and set the networking mode to Manual.
3. Enter valid numbers in the IP and Subnet fields.
4. When finished, select Apply.

17
Network Scan
The Network Scan feature automates frequency assignment by using a single receiver to scan and deploy frequencies to all networked receiver within the same
frequency band.

Network Scanning and Frequency Deployment

1. Connect receivers to an active Ethernet network. All receivers must be on the same subnet.
2. Prior to performing a network scan, turn on all receivers and allow 60 seconds for all receivers to join the network.
3. Choose a group or custom group for deployment on the receiver that will be used to initiate the network scan.
4. To start a network scan, press the menu button and navigate to the networkscan menu. Press enter.
5. When the scan is complete, the displays of receivers waiting for frequencies will flash.
6. Press enter to deploy the frequencies or press menu to cancel the deployment.
7. The front panel LEDs on each receiver will blink when a deployed frequency has been assigned.

Note: Full frequency deployment may not occur if the number of receivers in the network exceeds the number of available frequencies in the selected group. Try another
group or rescan after turning off unused receivers.

Connecting to an External Control System

The receiver connects to external controls systems (AMX or Crestron) via Ethernet cables.

Connection: Ethernet (TCP/IP; QLXD receiver is the client)

Port: 2202

For a comprehensive list of command strings, visit: http://shure.custhelp.com/

Shure AXT600 Spectrum Manager Compatibility

QLX-D receivers are compatible with the Axient AXT600 Spectrum Manager. Networked receivers will appear in the device inventory and frequencies from the
Compatible Frequency List can be deployed and monitored by the Spectrum Manager. For more information regarding the Spectrum Manager, see the Axient System
Guide.

Using QLX-D with a Shure ULX-D System

Transmitters and receivers from QLX-D and ULX-D component groups can be paired to form audio channels.

To ensure functionality, use the following settings on receivers and transmitters:

Encryption set to Off

High Density Mode set to Off (ULX-D receiver)
Manually tune the receiver and transmitter to the same frequency. IR sync between QLX-D and ULX-D components is not supported.

To create an audio channel, manually set the receiver frequency to match the frequency of the transmitter.

18
Managing QLX-D with Wireless Workbench 6
Shure's Wireless Workbench 6 (WWB6) software enables networked monitoring and control of the QLX-D receiver. Additional tools in WWB6 offer RF spectrum
monitoring, network configuration, and firmware updating.

Visit www.shure.com/wwb for a free download of Wireless Workbench software.

Managing and Monitoring Settings

Manage and monitor receiver settings by opening the Monitor tab in Wireless
Workbench. Click on the Settings button to show or hide the full Properties window.


RF and Audio Meters
Displays: current levels, band, TV, and TX Overload


Transmitter Settings


Displays: RF Power, Tx Type, Mic Offset, Tx Lock


Frequency Settings


Use drop-down to edit frequency value


Encryption Icon
Illuminates when Encryption is enabled

Receiver Gain Setting

Use drop-down to increase or decrease gain settings


10
Custom Groups


Click to enter to create custom groups

Utilities
Access receiver functions

Network Tab
Set network mode, view: IP address, Subnet, MAC, Firmware version, Network reset

Encryption
Enable/Disable Encryption

Receiver Locks
Lock/Unlock: Menu, Gain, Power

Viewing the Receiver in WWB6 Inventory

Click on the Inventory tab to view the receiver channels. Double-click on parameters to
enable editing.

Tip: Clicking on the receiver icon next to the channel name flashes the front panel LEDs on
the receiver for remote identification.

Hardware Identify
When Hardware Identify is triggered from a receiver, the corresponding representation of that receiver is flashed in the WWB inventory display, allowing for remote
identification.

Hardware Identify can be triggered from the receiver by pressing and holding the enter button for at least 3 seconds. Click the Dismiss button on the WWB Inventory
screen to exit the function.

19
Firmware Updates
Firmware is embedded software in each component that controls functionality. Periodically, new versions of firmware are developed to incorporate additional features and
enhancements.

Firmware Versioning
When updating receiver firmware, update transmitters to the same firmware version to ensure consistent operation.

The firmware version is numbered in the form of MAJOR.MINOR.PATCH (e.g., 1.2.14). At a minimum, all devices on the network (including transmitters), must have the
same MAJOR and MINOR firmware version numbers (e.g., 1.2.x).

Downloading and Updating Firmware

A free Shure Update Utility tool is available by visiting www.shure.com. The Shure Update Utility is also bundled with Shure Wireless Workbench software.

Refer to the help instructions to use the Shure Update Utility.

Updating the Receiver Updating the Transmitter

CAUTION! Ensure that receiver power and network connections are When firmware is downloaded to the receiver, it includes firmware updates for the
maintained during a firmware update. Do not turn off the receiver until transmitter. Updated firmware is passed from the receiver to the transmitter using the IR
the update is complete. Sync port.

1. Connect the receiver and computer to the same network.

2. Open the Shure Update Utility. 1. Press menu while holding the enter button to access the advanced menu. Use the
3. Click on the firmware tab to find available updates.
menu button to navigate to the update menu.

4. Use the Import button if manually importing firmware files.

2. Press enter to start the update.
5. Click the UpdateDevice tab and check the Versiontoinstall
box next to each device. 3. When the red IR LED flashes, align the receiver
and transmitter IR sync ports. The red LED will
6. Click SendUpdates to load the firmware to the networked devices. remain illuminated to indicate correct alignment
7. When the download is complete, the receiver will reboot with the and the download will automatically start.
updated firmware installed. 4. Maintain alignment during the update and
monitor download progress (0 to 100%) on the
receiver screen.
Tx
II
II
IIIIII IIIIIII < 15 cm (6 in.)
III
III

III
IIIIIIIIIIIII
Tx

5. When the update is complete, "TXUpdategood" is shown on the receiver display.

Error Codes and Solutions

Error codes are generated when the receiver detects a condition that can potentially affect system performance.

If an error is displayed on the receiver, use the following table to identify the problem and find the corresponding solution.

Error Code Description Solutions

Err.001 Audio Compatibility Update transmitter and receiver firmware to the latest version.
Err.002 Encryption Mismatch between Shure product lines Set encryption to off for components from different Shure products lines, such as
QLX-D and ULX-D.
Err.003 Encryption Mode Mismatch Perform an IR sync between the transmitter and receiver to clear the error.
Err.004 Band Mismatch Receiver and transmitter are operating in overlapping frequencies from different
bands.
Err.005 Frequency Mismatch Receiver and transmitter are from bands that do not share compatible
frequencies.
Err.006 No Frequencies Found Rescan, select a different group, or use WWB to find a frequency.
Err.007 Firmware Mismatch Update firmware on the transmitter and receiver.
Err.008 Shure SB900 battery runtime does not appear on Check that battery is firmly installed into the battery compartment. If condition
display persists, replace the battery.

20
Troubleshooting
Issue See Solution...
No Sound Power, Cables, or Radio Frequency
Faint sound or distortion Gain, Cables, Reducing Interference or Radio Frequency
Lack of range, unwanted noise bursts, or dropouts RF
Cannot turn transmitter off or change frequency settings, or can't program Interface Locks
receiver
Receiver display shows FAIL after encryption is disable Encryption Mismatch
Group and Channel display shows "--" Custom Group IR Sync

Power Radio Frequency (RF)

Make sure that the receiver and transmitter are receiving sufficient voltage. The blue RF LED will illuminate when a linked transmitter is within range of the
Check the battery indicators. Replace or recharge the batteries if necessary. receiver. Measure the transmitter range before a performance to avoid operating
beyond the specified transmitter range.
Gain The RF meter bars indicate amount of RF power being received. This signal
Adjust the system gain on the front of the receiver. Ensure the mic/line could be from the transmitter, or it could be from an interfering source, such
switch setting (XLR output only) on the back of the receiver corresponds to as a television broadcast. If the meter shows a signal level when the transmitter
the input of the mixing console, amplifier, or processor. is off, then that channel may have interference. Check the surrounding area for
sources of interference or change the receiver to a clear frequency.
Cables A red RF LED indicates RF overload. Avoid operating multiple systems in close
Check that all cables and connectors are fully engaged or locked into proximity.
position. Inspect cables for damage. Replace if necessary.
Frequency Compatibility
Interface Locks Perform a Scan and Sync to ensure the transmitter and receiver are set to the
The transmitter and the receiver can be locked to prevent accidental or same channel or frequency
unauthorized changes. If a locked control is accessed, the lock icon on the
Look at the label on the transmitter and receiver to make sure they are in the
display will flash. Follow the instructions to unlock the receiver or transmitter.
same band (G50, J50, L50, etc...).

Firmware Mismatch
Paired transmitters and receivers must have the same firmware version
Reducing Interference
installed to ensure consistent operation. See Firmware Updates topic for Perform a scan to find the best open frequency. Perform an IR sync to transfer
firmware update procedure. the settings to the transmitter.
For multiple systems, make sure that each receiver is assigned to a unique
Encryption Mismatch channel. Interference will occur if two transmitters are set to the same channel.
Indicates an encryption key mismatch has been detected. Perform an IR sync Maintain a line of sight between transmitter and receiver antennas.
between the receiver and transmitter to clear the error. Move receiver antennas away from metal objects or other sources of RF
interference (such as CD players, computers, digital effects, network switches,
Custom Group IR Sync network cables and Personal Stereo Monitor (PSM) wireless systems).
When using Custom Groups, always perform an IR sync from the Eliminate RF overload (see below).
CustomGroups menu in the receiver to ensure accurate display of group and
channel information. See CustomGroups topic for additional details.
Increasing Range
Increase transmitter RF power level to Hi
Use an active directional antenna, antenna distribution system, or other
antenna accessory to increase RF range

Eliminating RF Overload
If the RF OL icon appears on the RF meter, try the following:

Reduce the transmitter RF power level from Hi to Lo

Move the transmitter further away from the receiverat least 6 m (20 ft)
If you are using active antennas, reduce antenna or amplifier gain.
Use omnidirectional antennas

21
Hardware and Connectors
Single and Dual Rackmount Assembly

Securing the AC Power Cord Installing Footpads Receiver Output Connectors

47 F

instrument/ aux

50 47 F

47 F
50

a b c
-30 dB
mic/ line
47 F
50

TA4M Connections
SHIELD   5 V DC
47 F
1F
Audio Input Ground
N
Bias Voltage
440 pF

Ground Audio Input

Active Load
Ground

22
Optional Accessories

Batteries and Chargers UABIAST

Shure Lithium-Ion SB900 In-Line Power Supply UABIAST-US

Rechargeable Battery
UABIAST-UK
8-Pack Shure Lithium-Ion SB900-8
UABIAST-BR
Rechargeable Batteries
UABIAST-AR
8-Bay Shure Battery Charger SBC800-US
UABIAST-E
Dual Docking Charger With SBC200-US
PS45US Power Supply UABIAST-CHN
Dual Docking Charger, Power SBC200 UABIAST-K
Supply Not Included UABIAST-J
Single Battery Charger SBC100 UABIAST-AZ
Axient Charging Module SBC-AX UABIAST-TW
2-Bay Portable Battery SBC210
Charger With PS50US Power In-Line Amplifiers and Antennas
Supply
In-Line Antenna Amplifier, 792-810 UA830A
Bodypack Power Insert SBC-DC
MHz

Active Antenna Splitters In-Line Antenna Amplifier, UA830USTV

470-698MHz
Antenna Distribution System UA845 E In-Line Antenna Amplifier, 500-900 UA830WB
Antenna Distribution System UA845 E "B" MHz
Antenna Distribution System UA845J In-Line Antenna Amplifier UA830X
Antenna UHF-R 470-952 MHz UA845-SWB Active Directional Antenna UA874E
470-790MHZ
Antenna,Power Dist UHF-R UA845-SWB-AZ
470-952 MHz Active Directional Antenna UA874US
470-698MHZ
Antenna UHF-R 470-952 MHz UA845-SWB-BR
Active Directional Antenna UA874WB
Antenna,Power Dist UHF-R UA845-SWB-C
470-900MHZ
470-952 MHz
Active Directional Antenna UA874X
Antenna,Power Dist UHF -R UA845-SWB-E
925-952MHZ
470-952 MHz
Directional Wideband Antenna for PA805SWB
Antenna UHF-R 470-952 MHz UA845-SWB-K
PSM Systems
Antenna, Power Dist UHF-R UA845US
Directional Wideband Antenna for PA805X
470-952 MHz
PSM Systems

UHF Antenna Power Distribution Amplifiers Passive Omnidirectional Antenna UA860SWB

UHF Passive Antenna Splitter UA221
UHF Wideband Antenna UA844SWB/LC
Distributor w/o Power Cables Front Mount Antenna Kit (Includes 2 UA600
Cables And 2 Bulkhead)
UHF Antenna Power UA844SWB/LC-AR
Distribution System Remote Antenna Bracket With BNC UA505
Bulkhead Adaptor
UHF Antenna Power UA844SWB/LC-BR
Distribution System Helical Antenna, 470-900MHZ HA-8089

UHF Antenna Power UA844SWB/LC-AZ Helical Antenna, 944-952MHZ HA-8241

Distribution System
UHF Antenna Power UA844SWB/LC-C
Distribution System
UHF Antenna Power UA844SWB/LC-E
Distribution System
UHF Antenna Power UA844SWB/LC-J
Distribution Amplifier
UHF Antenna Power UA844SWB/LC-K
Distribution Amplifier
UHF Antenna Power UA844SWB/LC-UK
Distribution Amplifier

23
Cables and Connectors Hardware, Cases, and Accessories

Coaxial Cable, BNC-BNC, UA802 Hard Carrying Case For SLX System WA610
RG58C/U TYPE, 50 OHM, 2
Anti-Roll Device for Handheld Microphones A1K
FT Length (0.6 M)
Mute Switch for Shure Handheld UAMS/BK
Coaxial Cable, BNC-BNC, UA806
Transmitters
RG58C/U TYPE, 50 OHM, 6
FT Length (2 M) Cable, Instrument, 2.5 foot (.75 m), 4 WA302
Pin Mini Connector (TA4F) to 1/4-inch
Coaxial Cable, BNC-BNC, UA825
Connector.
RG8X/U TYPE, 50 OHM, 25
FT Length (7.5 M) Cable, Instrument, 2-foot (0.7m), 4-pin Mini WA304
Connector (TA4F) with Right-Angle 1/4-
Coaxial Cable, BNC-BNC, UA850
inch Connector, used with Shure Wireless
RG8X/U TYPE, 50 OHM, 50
Bodypack Transmitters
FT Length (15 M)
Premium Guitar Cable TQG Threaded WA305
Coaxial Cable, BNC-BNC, UA8100
Connector
RG213/U TYPE, 50 OHM, 100
FT Length (30 M) Premium Guitar Cable TQG Latching WA306
Connector
Ethernet Jumper Cable, 8" C8006
Cable, Microphone, 4-foot (1.3m), 4-pin Mini WA310
Ethernet Cable, 3 FT. C803
Connector (TA4F) to XLR Connector (F),
Ethernet Cable, 10 FT. C810 used with Shure Bodypack Transmitters.
Ethernet Cable, Ruggedized, C8100 In-line audio mute switch for Shure WA360
100 FT. wireless bodypack transmitters with a TA4F
connector.
Ethernet Cable, Ruggedized, C825
25 FT. In-Line Bodypack Mute Switch WA661
Ethernet Cable, Ruggedized, C850 Securely mounts the Shure wireless WA371
50 FT. handheld transmitters to standard
microphone stands.
1/2 Wave Omnidirectional Receiver Antennas Neoprene bodypack arm pouch for all Shure WA620
bodypack transmitters
470-542 MHz UA8-470-542
500-560 MHz UA8-500-560
518-598 MHz UA8-518-598
554-638 MHz UA8-554-638
596-698 MHz UA8-596-698
670-742 MHz UA8-670-742
690-746 MHz UA8-690-746
694-758 MHz UA8-694-758
710-790 MHz UA8-710-790
740-814 MHz UA8-740-814
750-822 MHz UA8-750-822
774-865 MHz UA8-774-865
00-1000 MHz UA8-900-1000

24
QLXD Specifications

RF Carrier Frequency Range Audio Dynamic Range

470937.5MHz, varies by region (See Frequency Range and Output Power table) System Gain @ +10
Working Range >120dB, A-weighted, typical
100m (328ft) Total Harmonic Distortion
Note: Actual range depends on RF signal absorption, reflection and interference. 12 dBFS input, System Gain @ +10
RF Tuning Step Size <0.1%
25kHz, varies by region System Audio Polarity
Image Rejection Positive pressure on microphone diaphragm produces positive voltage on pin 2 (with respect to pin 3 of
>70dB, typical XLR output) and the tip of the 6.35 mm (1/4-inch) output.
RF Sensitivity Operating Temperature Range
-97dBm at 10-5 BER -18C (0F) to 50C (122F)
Latency Note: Battery characteristics may limit this range.
<2.9ms Storage Temperature Range
Audio Frequency Response -29C (-20F) to 74C (165F)
Note: Battery characteristics may limit this range.
QLXD1 20 20kHz (1dB)

QLXD2 Note: Dependent on microphone type

QLXD4 QLXD1 QLXD2

Dimensions Mic Offset Range Mic Offset Range
41mm x 197mm x 151mm (1.63 in. x 7.75 in. x 5.94 in.), 0 to 21dB (in 3 dB steps) 0 to 21dB (in 3 dB steps)
HxWxD Battery Type Battery Type
Weight Shure SB900 Rechargeable Li-Ion or AA batteries 1.5V Shure SB900 Rechargeable Li-Ion or AA batteries 1.5V
777g (1.71lbs), without antennas Battery Runtime Battery Runtime
Housing @ 10mW @ 10mW
steel
Shure SB900 up to10hours Shure SB900 up to10hours
Power Requirements
12VDC @ 0.4 A, supplied by external power supply (tip alkaline up to 9hours alkaline up to 9hours
positive) See Battery Runtime Chart See Battery Runtime Chart
Dimensions Dimensions
RF Input
86mm x 65mm x 23mm (3.38in. x 2.57 in. x 0.92 in.) H x W 256mm x 37mm (10.1 in. x 1.5 in.) L x Dia.
Spurious Rejection x D,without antenna Weight
>80dB, typical Weight 347g (12.2oz.), without batteries
Connector Type 138g (4.9oz.), without batteries Housing
BNC Housing Machined aluminum
Impedance Cast aluminum
50 Audio Input
Audio Input Configuration
Audio Output
Connector Unbalanced
Gain Adjustment Range 4-Pin male mini connector (TA4M), See drawing for details Maximum Input Level
-18 to +42dB in 1 dB steps Configuration 1 kHz at 1% THD
Configuration Unbalanced 145dB SPL (SM58), typical
1/4" (6.35 mm) Impedance balanced Impedance Note: Dependent on microphone type
(Tip=audio, Ring=no audio,
1M, See drawing for details
Sleeve=ground)
Maximum Input Level RF Output
XLR balanced (1=ground, 1 kHz at 1% THD Antenna Type
2=audio +, 3=audio )
8.5 dBV (7.5 Vpp) Integrated Single Band Helical
Impedance Preamplifier Equivalent Input Noise (EIN) Occupied Bandwidth
1/4" (6.35 mm) 100 (50 Unbalanced) System Gain Setting +20 <200kHz
-120 dBV, A-weighted, typical Modulation Type
XLR 100
Shure proprietary digital
Full Scale Output RF Output Power
1/4" (6.35 mm) +12 dBV Connector 1mW or 10mW
SMA See Frequency Range and Output Power table, varies
XLR LINE setting= +18 dBV, by region
MIC setting= -12 dBV Antenna Type
1/4 wave
Mic/Line Switch
Impedance
30 dB pad
50
Phantom Power Protection
Occupied Bandwidth
1/4" (6.35 mm) Yes <200kHz
XLR Yes Modulation Type
Shure proprietary digital
Networking Power
1mW or 10mW
Network Interface
See Frequency Range and Output Power table, varies by
Single Port Ethernet 10/100 Mbps region
Network Addressing Capability
DHCP or Manual IP address
Maximum Cable Length
100m (328ft)

25
FREQUENCIES FOR EUROPEAN COUNTRIES

Country Code Frequency Range

Code de Pays Gamme de frequences
Codice di paese Gamme di frequenza
Cdigo de pas Gama de frequencias
Lnder-Krzel Frequenzbereich

QLXD-G51 A, B, BG, CH, CY, CZ, D, DK, EST, F, * *NOTE: This Radio equipment is intended for use in musical professional
FIN, GB, GR, H, HR, I, IRL, IS, L, LT, * entertainment and similar applications. This Radio apparatus may be capable
470 - 534 MHz
M, N, NL, P, PL RO, S, SK, SLO, TR, * of operating on some frequencies not authorized in your region. Please contact
1 or 10 mW All other countries * your national authority to obtain information on authorized frequencies and RF
QLXD-H51
A, B, BG, CH, CY, CZ, D, DK, EST, F, * power levels for wireless microphone products.
FIN, GB, GR, H, HR, I, IRL, IS, L, LT, *
534 - 598 MHz
M, N, NL, P, PL RO, S, SK, SLO, TR, *
1 or 10 mW *REMARQUE : Ce matriel radio est prvu pour une utilisation en spectacles
All other countries *
A, B, BG, CH, CY, CZ, D, DK, EST, F, * musicaux professionnels et applications similaires. Il est possible que cet
QLXD-K51
FIN, GB, GR, H, HR, I, IRL, IS, L, LT, *
appareil radio soit capable de fonctionner sur certaines frquences non
606 - 670 MHz autorises localement. Se mettre en rapport avec les autorits comptentes
M, N, NL, P, PL RO, S, SK, SLO, TR, *
1 or 10 mW
All other countries *
pour obtenir les informations sur les frquences et niveaux de puissance HF
A, B, BG, CH, CY, CZ, D, DK, EST, F, *
autoriss pour les systmes de microphones sans fil.
QLXD-L52
FIN, GB, GR, H, HR, I, IRL, IS, L, LT, *
632 - 694 MHz
M, N, NL, P, PL RO, S, SK, SLO, TR, * *HINWEIS: Diese Funkausrstung ist zum Gebrauch bei professionellen
1 or 10 mW
All other countries * Musikveranstaltungen und hnlichen Anwendungen vorgesehen. Dieses Gert
QLXD-P51
A, B, BG, CH, CY, CZ, D, DK, EST, F, * kann mglicherweise auf einigen Funkfrequenzen arbeiten, die in Ihrem Gebiet
710 - 782 MHz
FIN, GB, GR, H, HR, I, IRL, IS, L, LT, * nicht zugelassen sind. Wenden Sie sich bitte an die zustndige Behrde, um
M, N, NL, P, PL RO, S, SK, SLO, TR, * Informationen ber zugelassene Frequenzen und erlaubte Sendeleistungen fr
1 or 10 mW
all other countries * drahtlose Mikrofonprodukte zu erhalten.
A, B, BG, CH, CY, CZ, D, DK, EST, F, *
QLXD-Q51
FIN, GB, GR, H, HR, I, IRL, IS, L, LT, *
794 - 806 MHz *NOTA: Este equipo de radio est destinado para uso en presentaciones
M, N, NL, P, PL RO, S, SK, SLO, TR, *
1 or 10 mW musicales profesionales y usos similares. Este aparato de radio puede ser
All other countries *
capaz de funcionar en algunas frecuencias no autorizadas en su regin. Por
D license free
QLXD-S50 favor comunquese con las autoridades nacionales para informacin sobre
A, B, BG, CH, CY, CZ, D, DK, EST, F, *
las frecuencias autorizadas y los niveles de potencia de radiofrecuencia para
823 - 832 MHz FIN, GB, GR, H, HR, I, IRL, IS, L, LT, *
micrfonos inalmbricos.
863 - 865 MHz M, N, NL, P, PL RO, S, SK, SLO, TR, *
1 or 10 mW 863 - 865 MHz EU: license free
all other countries * *NOTA: questo apparecchio radio concepito per l'intrattenimento musicale
a livello professionale ed applicazioni simili. Questo apparecchio radio pu
essere in grado di funzionare a frequenze non autorizzate nel Paese in cui si
trova l'utente. Rivolgetevi alle autorit competenti per ottenere le informazioni
relative alle frequenze ed ai livelli di potenza RF autorizzati nella vostra regione
per i prodotti radiomicrofonici.

*OPMERKING: Deze radioapparatuur is bedoeld voor gebruik bij

professionele muzikale amusementsproducties en soortgelijke toepassingen.
Dit radioapparaat kan mogelijk werken op bepaalde frequenties die niet zijn
toegestaan in uw regio. Raadpleeg de autoriteiten in uw land voor informatie
over goedgekeurde frequenties en RF-vermogensniveaus voor draadloze
microfoons.

*.

. ,
,
.

.

26
Certifications
This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.

The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance

Authorized European representative:

Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: 49-7262-92 49 0
Fax: 49-7262-92 49 11 4
Email: [email protected]

Approved under the Declaration of Conformity (DoC) provision of FCC Part 15.

Certified by IC in Canada under RSS-210.

Conforms to electrical safety requirements based on IEC 60065.

Complies with and/or is certified to RSS-210, RSS-GEN.

Certified by IC in Canada under RSS-123 and RSS-102.

Certified under FCC Part 74.

QLXD1, QLXD2
IC: 616A-QLXD1G50, 616A-QLXD1H50, 616A-QLXD1J50, 616A-QLXD1L50, 616A-QLXD2G50, 616A-QLXD2H50, 616A-QLXD2J50, 616A-QLXD2L50.

FCC: DD4QLXD1G50, DD4QLXD1H50, DD4QLXD1J50, DD4QLXD1L50, DD4QLXD2G50, DD4QLXD2H50, DD4QLXD2J50, DD4QLXD2L50.

27