OWNERS MANUAL Be sure to write your model number and serial number here for

future reference. You can find these numbers printed on the bot-
tom of the table.
Table Tennis Table
Patent Pending MODEL # T8179

SERIAL #

READ ASSEMBLY, OPERATING AND SAFETY INSTRUCTIONS

CAUTION: CAREFULLY! AT LEAST TWO ADULTS ARE NEEDED TO PUT
THIS TABLE TOGETHER!

Thank you for buying our product. We try hard to ensure that our products are of high quality and free of problems, such as manufacturing
defects or missing parts. However, if you have any problems with your new product, please DO NOT RETURN IT TO THE STORE!.

DO NOT RETURN THIS PRODUCT TO THE STORE!

Call us at:

TOLL FREE 1-866-873-3528

(THIS IS A CONSUMER ONLY NUMBER)
Please have this Owners Manual with you when you call.

Or write us at: CUSTOMER SERVICE DEPT., P.O. Box 889, Evansville, IN 47706
Fax Number: (812) 467-1399.

Or E-mail us at: [email protected]

Please provide model number and/or part number (not just the key number) of the product and/or part when you call or write. These numbers can be found
on the product, packaging, and/or in this Owners Manual.

TOOLS NEEDED:
Phillips Screwdriver, Two 7/16 Wrenches, One 3/8 Wrench (an adjustable wrench may be substituted for the wrenches),
Flat Blade Screw Driver

2L-4105-00
 INSTALL SAFETY LATCHES #8 AS SHOWN ABOVE FOR PROPER USE OF
CAUTION: TABLE! DO NOT SKIP THIS STEP! DO NOT OPERATE TABLE UNTIL
SAFETY LATCHES ARE INSTALLED AND ASSEMBLY IS COMPLETE!

Figure 1

1. Gently tap four caster sockets #12 into Name Panel Assemblies until flange on sockets touches the edge of the tube. DO NOT
HIT CASTER SOCKET TOO HARD WITH A HAMMER! Sockets may break if hit too hard. See Figure 1.

2. Insert casters #11 into caster sockets #12.

3. Connect the two Name Plate Assemblies to the Cross Support #28, as shown in Figure 1, using four bolts #31 and four nuts #15.

4. Install a safety latch #8 into the right-hand hole on each name panel as shown in Figure 1. Use one screw #10 one washer #17
and one hex nut #16. NOTE: Flange on safety latch must extend over top of name panel as shown in Figure 1. Safety latch
must pivot freely.

5. Rotate U-support #7 until you see the screw holes in the

slots of U-clips #3. Slide U-support #7 side to side if
necessary. See Figure 2.

6. Rotate U-leg #2 until you see the screw hole in the slot of
center U-clip #3. Slide U-leg #2 side to side if necessary. Figure 2
See Figure 2.

7. Insert a screw #19 through slot in U-clips #3 and into each

hole in U-support #7 and center hole in U-leg #2. Thread it
all the way in until it touches the back of the tube. There
should be about 3/8 inch of screw #19 left sticking out.

2
8. Lay table top #1 painted side down, on a smooth, flat surface.
Use the shipping container to protect the painted surface of Figure 3
the table top.

9. Attach end of linkages #4 with two holes to INSIDE of U-leg #2

as shown in Figure 3. Secure with screws #14, locknuts #16
and plastic spacers #35. Tighten hardware snug enough to
keep table stable but do not overtighten. Tubes must pivot
freely. NOTE: Plastic spacers go between linkages #4 and U-
leg #2.

10. Attach other end of linkages #4 to OUTSIDE of U-support #7

with screws #18, locknuts #16 and plastic washers #24. Tighten
hardware until snug but do not overtighten. Tubes must pivot
freely.
11. Attach corner protectors (#22) to rails using tree plugs (#23).
Simply push the plugs through the protector and into the rail
until snug.

12. On one side of the table attach slotted end of safety strap #33
to INSIDE of U-Leg #2 using one bolt #36, one spacer #34,
one washer #24, and one hex nut #15. Tighten hardware until
snug but do not overtighten. Tubes must pivot freely. See Fig-
ure 4.

13. Attach other end of safety strap #33 to OUTSIDE of linkage #4

Figure 4
using one bolt #9, one washer #24, one spacer #34, and one
hex nut #15.

14. Prepare an area for the assembly of the second table top half.
If necessary, move the first table top half aside with the aid of
a helper. Be sure to place it in a location where it won't be
disturbed or damaged. If setting on its side, be sure to place
the bottom edge no less than 12 inches away form the wall.
Also be sure to place carpet or pieces of the shipping carton
down to protect table top edges. If floor is not carpeted, brace
table top half with a heavy object to keep it from sliding.

15. Repeat steps 5 thru 13 on second table half.

Figure 5

AT LEAST TWO (2) ADULTS ARE NEEDED TO

COMPLETE THE REST OF THIS ASSEMBLY!
WHEN ASSEMBLING TOPS TO BASE, HANDLE
TOP ASSEMBLIES BY GRASPING ONLY THE
TOPS THEMSELVES. DO NOT GRASP METAL
LEGS, U-SUPPORT, LINKAGE, OR HINGES.
THESE PARTS CAN MOVE AND COULD PINCH
FINGERS OR HANDS CAUSING SERIOUS
INJURY! ASSEMBLE AS SHOWN WITH LEGS
FULLY CLOSED AND TOPS IN A VERTICAL
POSITION. DO NOT OPEN LEGS AND TRY TO
ASSEMBLE. TABLE TOPS ARE HEAVY - DO NOT
ATTEMPT TO ASSEMBLE ALONE!

16. With two adults, attach table top (#1) to table base, as shown
in Figure 5. With at least one adult on each side of table top, lift
top and align ends of "U"-support tube with top of upright tubes.
Slide tubes together.
DO NOT OPEN THE TABLE TO PLAYING POSITION
17. With two adults, put other table top onto other pivot tubes fol- UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
lowing instructions in previous step. TABLE STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.
3
 NET ASSEMBLY
Net System Description 1. Net Post Assembly

Attach plastic net post as shown with washer and knob. Note:
there is a left and right net post assembly (See Net System
Description). Post assembly should rest flat against nut plate.
Slide the net sleeve over the vertical post while the net post
assembly is folded in toward the side of the table top. Fold the
net post assembly out against the net post stop into the post
and secure bead chain in catch.

2. Adjustments 3. Storage

A - Adjust overall net tension by slightly loosening the knob WARNING! Net posts must be pivoted toward
and moving net post assembly. Moderately tighten knob. Net side of table before lifting tops to storage or
post assembly should be kept square with the table by the net
post stop (See Net System Description). playback positions.

B - Adjust tension of cord with bead chain on each side. As- Loosen knob and pivot net post toward table side as far as it
sure that chain is fully seated in catch. will go. Retighten Knob.

C - Position top of net to a regulation height of 6

from the table surface by firmly gripping the vertical net post
within height adjustment slot.

4
 OPENING AND CLOSING INSTRUCTIONS
READ OPERATING INSTRUCTIONS CAREFULLY BEFORE OPERATING TABLE!
DO NOT ALLOW CHILDREN TO OPEN TABLE! DO NOT CLIMB, STAND OR
JUMP ON TABLE! SERIOUS OR FATAL INJURY MAY RESULT! THIS IS NOT A
CAUTION: TOY! TABLE IS TO BE OPENED OR CLOSED BY ADULTS ONLY! FAILURE TO
COMPLY WITH OPENING AND CLOSING INSTRUCTIONS COULD RESULT IN
PERSONAL INJURY OR PROPERTY DAMAGE.

TO OPEN: TO CLOSE:
1. Stand behind the table near the safety latch. WARNING! Net posts must be pivoted toward side of table
2. Hold table half with one hand and pivot safety latch enough before lifting tops to storage or playback positions.
to allow the edge of the table half to pass over it. 1. Pivot net post toward side of table.
3. While keeping an eye on the safety latch, pivot table half 2. Lift table half upward and inward to vertical position.
until it moves past the safety latch. Once edge of table has 3. Check to be sure that table half is locked in the safety latch.
passed over safety latch, stop pivoting table half. 4. Repeat for the other table half.
4. With both hands on the table half, center yourself along the
table half and lower the table half to the floor.
5. Repeat for the other table half.

5
 CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps, you will add
to the life of your new table.

CARE AND MAINTENANCE

You have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps you will add
to the life of your new table. The top (playing surface) of your table is of aluminum construction. It can be affected by atmospheric
conditions, meaning both temperature and humidity. This may cause a slight sag or distortion as top expands or contracts. This is
normal and should not cause concern as it does not detract from the play or utility value of the table.

STORAGE OF YOUR TABLE

Wind gusts can blow over or unexpectedly open the table; Store in protected area. When your table is not in use, it should be folded up
in a dry area.

CLEANING YOUR TABLE

To clean your table use a soft damp NOT WET cloth only. To prevent damage to your table's playing surface DO NOT use any
chemicals, abrasive, or cleaning products on your table's playing surface.
IMPORTANT: Periodically, lubricate all moving parts, including pivot points, to assure smooth opening and closing. A light lubricant
such as WD-40 is recommended.

LIMITED WARRANTY
Manufacturer warrants to the original retail purchaser, this product to be free from defects in material and workmanship for a period of ninety (90)
days from the date of purchase.

Should this product become defective due to material or workmanship within the warranty period, contact our Customer Service Department for
repair or replacement at our option.

This warranty is not transferable and does not cover normal wear and tear, bowing of the table or damage caused by improper handling, installation
or use of this product. This warranty is also void if product is in any way abused, damaged, or modified from its original state, or if used for other than
residential use.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

6
 PRODUCT PARTS LIST T8179
Key # Part # Description Qty. Key # Part # Description Qty.

1 4A-5319-10 Half Top 2 21 8S-6603-12 Upright Tube 4

2 8S-5550-01 U-leg 2 22 3M-6389-00 Corner Cap 4
3 2S-6319-02 1- U-Clip 12 23 3M-4118-00 Tree Plug 8
4 8S-6635-03 Linkage 4 24 2B-6087-00 Plastic Washer 8
5 2S-6419-03 Name Panel 2 25 8S-4111-00 Side Rail R.H. 2
7 8S-6639-02 U-support 2 8S-4112-00 Side Rail L.H. 2
8 2S-6264-03 Safety Latch 2 26 8S-4078-00 End Rail 2
9 701-47 -20 x 1 Hex Head Bolt 10 27 5A-6781-00 Net and Post Kit 1
10 801-120B #10-24 x 3/4 Phil Rnd Hd Scr 2 28 1A-6326-02 Cross Brace 1
11 2Q-6105-01 Caster 4 29 1A-6285-00 Nut Plate 2
12 3M-6115-00 Caster Socket 4 30 8S-4113-00 Inner Rail 2
13 3M-6447-00 Leg Cap 4 31 1B-4078-00 -20 x 1/2 Hex Head Bolt 4
14 701-166 -20 x 3 Hex Head Bolt 4 32 1B-4084-00 #8 x 13/32 Sheet Metal Screw 6
15 701-26 -20 Locknut 16 33 2S-6428-03 Safety Strap 2
16 601-80B #10-24 Locknut 10 34 7B-6257-00 5/16 Spacer 4
17 701-1B 3/16 Flatwasher 2 35 7B-6256-00 3/4 Spacer 4
18 701-142 -20 x 2 1/4 Hex Head Bolt 4 36 701-82 -20 x 2 Hex Head Bolt 2
19 1B-6452-00 #8-32 x 1 Self Tapping Screw 8 37 2L-4105-00 Owners Manual 1
20 1B-4090-00 #8 x 5/16 Sheet Metal Screw 118

7 2L-4105-00